blob: 1c476b635b690865cff0882578d72b1db2dc7c50 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/media/i2c/toshiba,tc358746.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Toshiba TC358746 Parallel to MIPI CSI2 Bridge
maintainers:
- Marco Felsch <kernel@pengutronix.de>
description: |-
The Toshiba TC358746 converts a parallel video stream into a MIPI CSI-2
stream. The direction can be either parallel-in -> csi-out or csi-in ->
parallel-out The chip is programmable through I2C and SPI but the SPI
interface is only supported in parallel-in -> csi-out mode.
Note that the current device tree bindings only support the
parallel-in -> csi-out path.
properties:
compatible:
const: toshiba,tc358746
reg:
maxItems: 1
clocks:
description:
The phandle to the reference clock source. This corresponds to the
hardware pin REFCLK.
maxItems: 1
clock-names:
const: refclk
"#clock-cells":
description: |
The bridge can act as clock provider for the sensor. To enable this
support #clock-cells must be specified. Attention if this feature is used
then the mclk rate must be at least: (2 * link-frequency) / 8
`------------------ยด ^
internal PLL rate smallest possible
mclk-div
const: 0
clock-output-names:
description:
The clock name of the MCLK output, the default name is tc358746-mclk.
maxItems: 1
vddc-supply:
description: Digital core voltage supply, 1.2 volts
vddio-supply:
description: Digital I/O voltage supply, 1.8 volts
vddmipi-supply:
description: MIPI CSI phy voltage supply, 1.2 volts
reset-gpios:
description:
The phandle and specifier for the GPIO that controls the chip reset.
This corresponds to the hardware pin RESX which is physically active low.
maxItems: 1
ports:
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
description: Input port
properties:
endpoint:
$ref: /schemas/media/video-interfaces.yaml#
unevaluatedProperties: false
properties:
hsync-active: true
vsync-active: true
bus-type:
enum: [ 5, 6 ]
required:
- hsync-active
- vsync-active
- bus-type
port@1:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
description: Output port
properties:
endpoint:
$ref: /schemas/media/video-interfaces.yaml#
unevaluatedProperties: false
properties:
data-lanes:
minItems: 1
maxItems: 4
clock-noncontinuous: true
link-frequencies: true
required:
- data-lanes
- link-frequencies
required:
- port@0
- port@1
required:
- compatible
- reg
- clocks
- clock-names
- vddc-supply
- vddio-supply
- vddmipi-supply
- ports
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
csi-bridge@e {
compatible = "toshiba,tc358746";
reg = <0xe>;
clocks = <&refclk>;
clock-names = "refclk";
reset-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
vddc-supply = <&v1_2d>;
vddio-supply = <&v1_8d>;
vddmipi-supply = <&v1_2d>;
/* sensor mclk provider */
#clock-cells = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
/* Input */
port@0 {
reg = <0>;
tc358746_in: endpoint {
remote-endpoint = <&sensor_out>;
hsync-active = <0>;
vsync-active = <0>;
bus-type = <5>;
};
};
/* Output */
port@1 {
reg = <1>;
tc358746_out: endpoint {
remote-endpoint = <&mipi_csi2_in>;
data-lanes = <1 2>;
clock-noncontinuous;
link-frequencies = /bits/ 64 <216000000>;
};
};
};
};
};