| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/ |
| */ |
| /dts-v1/; |
| |
| #include "dra72x.dtsi" |
| #include "dra7-ipu-dsp-common.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/clock/ti-dra7-atl.h> |
| |
| / { |
| compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"; |
| |
| aliases { |
| display0 = &hdmi0; |
| }; |
| |
| chosen { |
| stdout-path = &uart1; |
| }; |
| |
| evm_12v0: fixedregulator-evm12v0 { |
| /* main supply */ |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_12v0"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| evm_5v0: fixedregulator-evm5v0 { |
| /* Output 1 of TPS43351QDAPRQ1 on dra72-evm */ |
| /* Output 1 of LM5140QRWGTQ1 on dra71-evm */ |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_5v0"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&evm_12v0>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| evm_3v6: fixedregulator-evm_3v6 { |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_3v6"; |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| vin-supply = <&evm_5v0>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vsys_3v3: fixedregulator-vsys3v3 { |
| /* Output 2 of TPS43351QDAPRQ1 on dra72-evm */ |
| /* Output 2 of LM5140QRWGTQ1 on dra71-evm */ |
| compatible = "regulator-fixed"; |
| regulator-name = "vsys_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&evm_12v0>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| evm_3v3_sw: fixedregulator-evm_3v3 { |
| /* TPS22965DSG */ |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vsys_3v3>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| aic_dvdd: fixedregulator-aic_dvdd { |
| /* TPS77018DBVT */ |
| compatible = "regulator-fixed"; |
| regulator-name = "aic_dvdd"; |
| vin-supply = <&evm_3v3_sw>; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| evm_3v3_sd: fixedregulator-sd { |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_3v3_sd"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&evm_3v3_sw>; |
| enable-active-high; |
| gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| extcon_usb1: extcon_usb1 { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| extcon_usb2: extcon_usb2 { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| hdmi0: connector { |
| compatible = "hdmi-connector"; |
| label = "hdmi"; |
| |
| type = "a"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&tpd12s015_out>; |
| }; |
| }; |
| }; |
| |
| tpd12s015: encoder { |
| compatible = "ti,tpd12s015"; |
| |
| gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ |
| <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ |
| <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| tpd12s015_in: endpoint { |
| remote-endpoint = <&hdmi_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| tpd12s015_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| sound0: sound0 { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "DRA7xx-EVM"; |
| simple-audio-card,widgets = |
| "Headphone", "Headphone Jack", |
| "Line", "Line Out", |
| "Microphone", "Mic Jack", |
| "Line", "Line In"; |
| simple-audio-card,routing = |
| "Headphone Jack", "HPLOUT", |
| "Headphone Jack", "HPROUT", |
| "Line Out", "LLOUT", |
| "Line Out", "RLOUT", |
| "MIC3L", "Mic Jack", |
| "MIC3R", "Mic Jack", |
| "Mic Jack", "Mic Bias", |
| "LINE1L", "Line In", |
| "LINE1R", "Line In"; |
| simple-audio-card,format = "dsp_b"; |
| simple-audio-card,bitclock-master = <&sound0_master>; |
| simple-audio-card,frame-master = <&sound0_master>; |
| simple-audio-card,bitclock-inversion; |
| |
| sound0_master: simple-audio-card,cpu { |
| sound-dai = <&mcasp3>; |
| system-clock-frequency = <5644800>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&tlv320aic3106>; |
| clocks = <&atl_clkin2_ck>; |
| }; |
| }; |
| |
| vmmcwl_fixed: fixedregulator-mmcwl { |
| compatible = "regulator-fixed"; |
| regulator-name = "vmmcwl_fixed"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| clk_ov5640_fixed: clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| }; |
| }; |
| |
| &dra7_pmx_core { |
| dcan1_pins_default: dcan1-default-pins { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ |
| DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ |
| >; |
| }; |
| |
| dcan1_pins_sleep: dcan1-sleep-pins { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ |
| DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| pcf_lcd: gpio@20 { |
| compatible = "nxp,pcf8575"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pcf_gpio_21: gpio@21 { |
| compatible = "nxp,pcf8575"; |
| reg = <0x21>; |
| lines-initial-states = <0x1408>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| tlv320aic3106: tlv320aic3106@19 { |
| #sound-dai-cells = <0>; |
| compatible = "ti,tlv320aic3106"; |
| reg = <0x19>; |
| adc-settle-ms = <40>; |
| ai3x-micbias-vg = <1>; /* 2.0V */ |
| status = "okay"; |
| |
| /* Regulators */ |
| AVDD-supply = <&evm_3v3_sw>; |
| IOVDD-supply = <&evm_3v3_sw>; |
| DRVDD-supply = <&evm_3v3_sw>; |
| DVDD-supply = <&aic_dvdd>; |
| }; |
| }; |
| |
| &i2c5 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| pcf_hdmi: pcf8575@26 { |
| compatible = "nxp,pcf8575"; |
| reg = <0x26>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| /* |
| * initial state is used here to keep the mdio interface |
| * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and |
| * VIN2_S0 driven high otherwise Ethernet stops working |
| * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 |
| */ |
| lines-initial-states = <0x0f2b>; |
| |
| hdmi-audio-hog { |
| /* vin6_sel_s0: high: VIN6, low: audio */ |
| gpio-hog; |
| gpios = <1 GPIO_ACTIVE_HIGH>; |
| output-low; |
| line-name = "vin6_sel_s0"; |
| }; |
| }; |
| |
| ov5640@3c { |
| compatible = "ovti,ov5640"; |
| reg = <0x3c>; |
| |
| clocks = <&clk_ov5640_fixed>; |
| clock-names = "xclk"; |
| |
| port { |
| csi2_cam0: endpoint { |
| remote-endpoint = <&csi2_phy0>; |
| clock-lanes = <0>; |
| data-lanes = <1 2>; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, |
| <&dra7_pmx_core 0x3e0>; |
| }; |
| |
| &elm { |
| status = "okay"; |
| }; |
| |
| &gpmc { |
| /* |
| * For the existing IOdelay configuration via U-Boot we don't |
| * support NAND on dra72-evm. Keep it disabled. Enabling it |
| * requires a different configuration by U-Boot. |
| */ |
| status = "disabled"; |
| ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ |
| nand@0,0 { |
| /* To use NAND, DIP switch SW5 must be set like so: |
| * SW5.1 (NAND_SELn) = ON (LOW) |
| * SW5.9 (GPMC_WPN) = OFF (HIGH) |
| */ |
| compatible = "ti,omap2-nand"; |
| reg = <0 0 4>; /* device IO registers */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ |
| ti,nand-xfer-type = "prefetch-dma"; |
| ti,nand-ecc-opt = "bch8"; |
| ti,elm-id = <&elm>; |
| nand-bus-width = <16>; |
| gpmc,device-width = <2>; |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <80>; |
| gpmc,cs-wr-off-ns = <80>; |
| gpmc,adv-on-ns = <0>; |
| gpmc,adv-rd-off-ns = <60>; |
| gpmc,adv-wr-off-ns = <60>; |
| gpmc,we-on-ns = <10>; |
| gpmc,we-off-ns = <50>; |
| gpmc,oe-on-ns = <4>; |
| gpmc,oe-off-ns = <40>; |
| gpmc,access-ns = <40>; |
| gpmc,wr-access-ns = <80>; |
| gpmc,rd-cycle-ns = <80>; |
| gpmc,wr-cycle-ns = <80>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,clk-activation-ns = <0>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| /* MTD partition table */ |
| /* All SPL-* partitions are sized to minimal length |
| * which can be independently programmable. For |
| * NAND flash this is equal to size of erase-block */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| partition@0 { |
| label = "NAND.SPL"; |
| reg = <0x00000000 0x00020000>; |
| }; |
| partition@1 { |
| label = "NAND.SPL.backup1"; |
| reg = <0x00020000 0x00020000>; |
| }; |
| partition@2 { |
| label = "NAND.SPL.backup2"; |
| reg = <0x00040000 0x00020000>; |
| }; |
| partition@3 { |
| label = "NAND.SPL.backup3"; |
| reg = <0x00060000 0x00020000>; |
| }; |
| partition@4 { |
| label = "NAND.u-boot-spl-os"; |
| reg = <0x00080000 0x00040000>; |
| }; |
| partition@5 { |
| label = "NAND.u-boot"; |
| reg = <0x000c0000 0x00100000>; |
| }; |
| partition@6 { |
| label = "NAND.u-boot-env"; |
| reg = <0x001c0000 0x00020000>; |
| }; |
| partition@7 { |
| label = "NAND.u-boot-env.backup1"; |
| reg = <0x001e0000 0x00020000>; |
| }; |
| partition@8 { |
| label = "NAND.kernel"; |
| reg = <0x00200000 0x00800000>; |
| }; |
| partition@9 { |
| label = "NAND.file-system"; |
| reg = <0x00a00000 0x0f600000>; |
| }; |
| }; |
| }; |
| |
| &omap_dwc3_1 { |
| extcon = <&extcon_usb1>; |
| }; |
| |
| &omap_dwc3_2 { |
| extcon = <&extcon_usb2>; |
| }; |
| |
| &usb1 { |
| dr_mode = "otg"; |
| extcon = <&extcon_usb1>; |
| }; |
| |
| &usb2 { |
| dr_mode = "host"; |
| extcon = <&extcon_usb2>; |
| }; |
| |
| &mmc1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins_default>; |
| vmmc-supply = <&evm_3v3_sd>; |
| bus-width = <4>; |
| /* |
| * SDCD signal is not being used here - using the fact that GPIO mode |
| * is a viable alternative |
| */ |
| cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; |
| max-frequency = <192000000>; |
| }; |
| |
| &mmc2 { |
| /* SW5-3 in ON position */ |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins_default>; |
| bus-width = <8>; |
| non-removable; |
| max-frequency = <192000000>; |
| }; |
| |
| &mmc4 { |
| status = "okay"; |
| vmmc-supply = <&evm_3v6>; |
| vqmmc-supply = <&vmmcwl_fixed>; |
| bus-width = <4>; |
| cap-power-off-card; |
| keep-power-in-suspend; |
| non-removable; |
| pinctrl-names = "default", "hs", "sdr12", "sdr25"; |
| pinctrl-0 = <&mmc4_pins_default>; |
| pinctrl-1 = <&mmc4_pins_default>; |
| pinctrl-2 = <&mmc4_pins_default>; |
| pinctrl-3 = <&mmc4_pins_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| wifi@2 { |
| compatible = "ti,wl1835"; |
| reg = <2>; |
| interrupt-parent = <&gpio5>; |
| interrupts = <7 IRQ_TYPE_EDGE_RISING>; |
| }; |
| }; |
| |
| &dcan1 { |
| status = "okay"; |
| pinctrl-names = "default", "sleep", "active"; |
| pinctrl-0 = <&dcan1_pins_sleep>; |
| pinctrl-1 = <&dcan1_pins_sleep>; |
| pinctrl-2 = <&dcan1_pins_default>; |
| }; |
| |
| &qspi { |
| status = "okay"; |
| |
| spi-max-frequency = <76800000>; |
| flash@0 { |
| compatible = "s25fl256s1"; |
| spi-max-frequency = <76800000>; |
| reg = <0>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <4>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| /* MTD partition table. |
| * The ROM checks the first four physical blocks |
| * for a valid file to boot and the flash here is |
| * 64KiB block size. |
| */ |
| partition@0 { |
| label = "QSPI.SPL"; |
| reg = <0x00000000 0x00010000>; |
| }; |
| partition@1 { |
| label = "QSPI.SPL.backup1"; |
| reg = <0x00010000 0x00010000>; |
| }; |
| partition@2 { |
| label = "QSPI.SPL.backup2"; |
| reg = <0x00020000 0x00010000>; |
| }; |
| partition@3 { |
| label = "QSPI.SPL.backup3"; |
| reg = <0x00030000 0x00010000>; |
| }; |
| partition@4 { |
| label = "QSPI.u-boot"; |
| reg = <0x00040000 0x00100000>; |
| }; |
| partition@5 { |
| label = "QSPI.u-boot-spl-os"; |
| reg = <0x00140000 0x00080000>; |
| }; |
| partition@6 { |
| label = "QSPI.u-boot-env"; |
| reg = <0x001c0000 0x00010000>; |
| }; |
| partition@7 { |
| label = "QSPI.u-boot-env.backup1"; |
| reg = <0x001d0000 0x0010000>; |
| }; |
| partition@8 { |
| label = "QSPI.kernel"; |
| reg = <0x001e0000 0x0800000>; |
| }; |
| partition@9 { |
| label = "QSPI.file-system"; |
| reg = <0x009e0000 0x01620000>; |
| }; |
| }; |
| }; |
| |
| &dss { |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| status = "okay"; |
| |
| port { |
| hdmi_out: endpoint { |
| remote-endpoint = <&tpd12s015_in>; |
| }; |
| }; |
| }; |
| |
| &atl { |
| assigned-clocks = <&abe_dpll_sys_clk_mux>, |
| <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>, |
| <&dpll_abe_ck>, |
| <&dpll_abe_m2x2_ck>, |
| <&atl_clkin2_ck>; |
| assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; |
| assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; |
| |
| status = "okay"; |
| |
| atl2 { |
| bws = <DRA7_ATL_WS_MCASP2_FSX>; |
| aws = <DRA7_ATL_WS_MCASP3_FSX>; |
| }; |
| }; |
| |
| &mcasp3 { |
| #sound-dai-cells = <0>; |
| |
| assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>; |
| assigned-clock-parents = <&atl_clkin2_ck>; |
| |
| status = "okay"; |
| |
| op-mode = <0>; /* MCASP_IIS_MODE */ |
| tdm-slots = <2>; |
| /* 4 serializer */ |
| serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ |
| 1 2 0 0 |
| >; |
| tx-num-evt = <32>; |
| rx-num-evt = <32>; |
| }; |
| |
| &pcie1_rc { |
| status = "okay"; |
| }; |
| |
| &csi2_0 { |
| csi2_phy0: endpoint { |
| remote-endpoint = <&csi2_cam0>; |
| clock-lanes = <0>; |
| data-lanes = <1 2>; |
| }; |
| }; |