blob: 4590186c4a0b822b140f470e90df5d4ffe2562b5 [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
# Copyright 2019 Analogix Semiconductor, Inc.
%YAML 1.2
---
$id: "http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
maintainers:
- Xin Ji <xji@analogixsemi.com>
description: |
The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
designed for portable devices.
properties:
compatible:
items:
- const: analogix,anx7625
reg:
maxItems: 1
interrupts:
description: used for interrupt pin B8.
maxItems: 1
enable-gpios:
description: used for power on chip control, POWER_EN pin D2.
maxItems: 1
reset-gpios:
description: used for reset chip control, RESET_N pin B7.
maxItems: 1
vdd10-supply:
description: Regulator that provides the supply 1.0V power.
vdd18-supply:
description: Regulator that provides the supply 1.8V power.
vdd33-supply:
description: Regulator that provides the supply 3.3V power.
analogix,lane0-swing:
$ref: /schemas/types.yaml#/definitions/uint8-array
minItems: 1
maxItems: 20
description:
an array of swing register setting for DP tx lane0 PHY.
Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and
[Swing control] setting.
Registers 0~9, bit 3:0 is [Boost control], these bits control
post cursor manual, increase the [Boost control] to increase
Pre-emphasis value.
Registers 0~9, bit 6:4 is [Swing control], these bits control
swing manual, increase [Swing control] setting to add Vp-p value
for each Swing, Pre.
Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
Swing1_Pre2, Swing0_Pre3, they are for [R select control] and
[R Termination control] setting.
Registers 10~19, bit 4:0 is [R select control], these bits are
compensation manual, increase it can enhance IO driven strength
and Vp-p.
Registers 10~19, bit 5:6 is [R termination control], these bits
adjust 50ohm impedance of DP tx termination. 00:55 ohm,
01:50 ohm(default), 10:45 ohm, 11:40 ohm.
analogix,lane1-swing:
$ref: /schemas/types.yaml#/definitions/uint8-array
minItems: 1
maxItems: 20
description:
an array of swing register setting for DP tx lane1 PHY.
DP TX lane1 swing register setting same with lane0
swing, please refer lane0-swing property description.
analogix,audio-enable:
type: boolean
description: let the driver enable audio HDMI codec function or not.
aux-bus:
$ref: /schemas/display/dp-aux-bus.yaml#
ports:
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
description:
MIPI DSI/DPI input.
properties:
endpoint:
$ref: /schemas/media/video-interfaces.yaml#
type: object
additionalProperties: false
properties:
remote-endpoint: true
bus-type:
enum: [7]
default: 1
data-lanes: true
port@1:
$ref: /schemas/graph.yaml#/properties/port
description:
Video port for panel or connector.
required:
- port@0
- port@1
required:
- compatible
- reg
- vdd10-supply
- vdd18-supply
- vdd33-supply
- ports
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
encoder@58 {
compatible = "analogix,anx7625";
reg = <0x58>;
enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
vdd10-supply = <&pp1000_mipibrdg>;
vdd18-supply = <&pp1800_mipibrdg>;
vdd33-supply = <&pp3300_mipibrdg>;
analogix,audio-enable;
analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;
analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;
ports {
#address-cells = <1>;
#size-cells = <0>;
mipi2dp_bridge_in: port@0 {
reg = <0>;
anx7625_in: endpoint {
remote-endpoint = <&mipi_dsi>;
bus-type = <7>;
data-lanes = <0 1 2 3>;
};
};
mipi2dp_bridge_out: port@1 {
reg = <1>;
anx7625_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
aux-bus {
panel {
compatible = "innolux,n125hce-gn1";
power-supply = <&pp3300_disp_x>;
backlight = <&backlight_lcd0>;
port {
panel_in: endpoint {
remote-endpoint = <&anx7625_out>;
};
};
};
};
};
};