| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Support for Macronix external hardware ECC engine for NAND devices, also | |
| * called DPE for Data Processing Engine. | |
| * | |
| * Copyright © 2019 Macronix | |
| * Author: Miquel Raynal <miquel.raynal@bootlin.com> | |
| */ | |
| #include <linux/dma-mapping.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/nand.h> | |
| #include <linux/mtd/nand-ecc-mxic.h> | |
| #include <linux/mutex.h> | |
| #include <linux/of.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/slab.h> | |
| /* DPE Configuration */ | |
| #define DP_CONFIG 0x00 | |
| #define ECC_EN BIT(0) | |
| #define ECC_TYP(idx) (((idx) << 3) & GENMASK(6, 3)) | |
| /* DPE Interrupt Status */ | |
| #define INTRPT_STS 0x04 | |
| #define TRANS_CMPLT BIT(0) | |
| #define SDMA_MAIN BIT(1) | |
| #define SDMA_SPARE BIT(2) | |
| #define ECC_ERR BIT(3) | |
| #define TO_SPARE BIT(4) | |
| #define TO_MAIN BIT(5) | |
| /* DPE Interrupt Status Enable */ | |
| #define INTRPT_STS_EN 0x08 | |
| /* DPE Interrupt Signal Enable */ | |
| #define INTRPT_SIG_EN 0x0C | |
| /* Host Controller Configuration */ | |
| #define HC_CONFIG 0x10 | |
| #define DEV2MEM 0 /* TRANS_TYP_DMA in the spec */ | |
| #define MEM2MEM BIT(4) /* TRANS_TYP_IO in the spec */ | |
| #define MAPPING BIT(5) /* TRANS_TYP_MAPPING in the spec */ | |
| #define ECC_PACKED 0 /* LAYOUT_TYP_INTEGRATED in the spec */ | |
| #define ECC_INTERLEAVED BIT(2) /* LAYOUT_TYP_DISTRIBUTED in the spec */ | |
| #define BURST_TYP_FIXED 0 | |
| #define BURST_TYP_INCREASING BIT(0) | |
| /* Host Controller Slave Address */ | |
| #define HC_SLV_ADDR 0x14 | |
| /* ECC Chunk Size */ | |
| #define CHUNK_SIZE 0x20 | |
| /* Main Data Size */ | |
| #define MAIN_SIZE 0x24 | |
| /* Spare Data Size */ | |
| #define SPARE_SIZE 0x28 | |
| #define META_SZ(reg) ((reg) & GENMASK(7, 0)) | |
| #define PARITY_SZ(reg) (((reg) & GENMASK(15, 8)) >> 8) | |
| #define RSV_SZ(reg) (((reg) & GENMASK(23, 16)) >> 16) | |
| #define SPARE_SZ(reg) ((reg) >> 24) | |
| /* ECC Chunk Count */ | |
| #define CHUNK_CNT 0x30 | |
| /* SDMA Control */ | |
| #define SDMA_CTRL 0x40 | |
| #define WRITE_NAND 0 | |
| #define READ_NAND BIT(1) | |
| #define CONT_NAND BIT(29) | |
| #define CONT_SYSM BIT(30) /* Continue System Memory? */ | |
| #define SDMA_STRT BIT(31) | |
| /* SDMA Address of Main Data */ | |
| #define SDMA_MAIN_ADDR 0x44 | |
| /* SDMA Address of Spare Data */ | |
| #define SDMA_SPARE_ADDR 0x48 | |
| /* DPE Version Number */ | |
| #define DP_VER 0xD0 | |
| #define DP_VER_OFFSET 16 | |
| /* Status bytes between each chunk of spare data */ | |
| #define STAT_BYTES 4 | |
| #define NO_ERR 0x00 | |
| #define MAX_CORR_ERR 0x28 | |
| #define UNCORR_ERR 0xFE | |
| #define ERASED_CHUNK 0xFF | |
| struct mxic_ecc_engine { | |
| struct device *dev; | |
| void __iomem *regs; | |
| int irq; | |
| struct completion complete; | |
| struct nand_ecc_engine external_engine; | |
| struct nand_ecc_engine pipelined_engine; | |
| struct mutex lock; | |
| }; | |
| struct mxic_ecc_ctx { | |
| /* ECC machinery */ | |
| unsigned int data_step_sz; | |
| unsigned int oob_step_sz; | |
| unsigned int parity_sz; | |
| unsigned int meta_sz; | |
| u8 *status; | |
| int steps; | |
| /* DMA boilerplate */ | |
| struct nand_ecc_req_tweak_ctx req_ctx; | |
| u8 *oobwithstat; | |
| struct scatterlist sg[2]; | |
| struct nand_page_io_req *req; | |
| unsigned int pageoffs; | |
| }; | |
| static struct mxic_ecc_engine *ext_ecc_eng_to_mxic(struct nand_ecc_engine *eng) | |
| { | |
| return container_of(eng, struct mxic_ecc_engine, external_engine); | |
| } | |
| static struct mxic_ecc_engine *pip_ecc_eng_to_mxic(struct nand_ecc_engine *eng) | |
| { | |
| return container_of(eng, struct mxic_ecc_engine, pipelined_engine); | |
| } | |
| static struct mxic_ecc_engine *nand_to_mxic(struct nand_device *nand) | |
| { | |
| struct nand_ecc_engine *eng = nand->ecc.engine; | |
| if (eng->integration == NAND_ECC_ENGINE_INTEGRATION_EXTERNAL) | |
| return ext_ecc_eng_to_mxic(eng); | |
| else | |
| return pip_ecc_eng_to_mxic(eng); | |
| } | |
| static int mxic_ecc_ooblayout_ecc(struct mtd_info *mtd, int section, | |
| struct mtd_oob_region *oobregion) | |
| { | |
| struct nand_device *nand = mtd_to_nanddev(mtd); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| if (section < 0 || section >= ctx->steps) | |
| return -ERANGE; | |
| oobregion->offset = (section * ctx->oob_step_sz) + ctx->meta_sz; | |
| oobregion->length = ctx->parity_sz; | |
| return 0; | |
| } | |
| static int mxic_ecc_ooblayout_free(struct mtd_info *mtd, int section, | |
| struct mtd_oob_region *oobregion) | |
| { | |
| struct nand_device *nand = mtd_to_nanddev(mtd); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| if (section < 0 || section >= ctx->steps) | |
| return -ERANGE; | |
| if (!section) { | |
| oobregion->offset = 2; | |
| oobregion->length = ctx->meta_sz - 2; | |
| } else { | |
| oobregion->offset = section * ctx->oob_step_sz; | |
| oobregion->length = ctx->meta_sz; | |
| } | |
| return 0; | |
| } | |
| static const struct mtd_ooblayout_ops mxic_ecc_ooblayout_ops = { | |
| .ecc = mxic_ecc_ooblayout_ecc, | |
| .free = mxic_ecc_ooblayout_free, | |
| }; | |
| static void mxic_ecc_disable_engine(struct mxic_ecc_engine *mxic) | |
| { | |
| u32 reg; | |
| reg = readl(mxic->regs + DP_CONFIG); | |
| reg &= ~ECC_EN; | |
| writel(reg, mxic->regs + DP_CONFIG); | |
| } | |
| static void mxic_ecc_enable_engine(struct mxic_ecc_engine *mxic) | |
| { | |
| u32 reg; | |
| reg = readl(mxic->regs + DP_CONFIG); | |
| reg |= ECC_EN; | |
| writel(reg, mxic->regs + DP_CONFIG); | |
| } | |
| static void mxic_ecc_disable_int(struct mxic_ecc_engine *mxic) | |
| { | |
| writel(0, mxic->regs + INTRPT_SIG_EN); | |
| } | |
| static void mxic_ecc_enable_int(struct mxic_ecc_engine *mxic) | |
| { | |
| writel(TRANS_CMPLT, mxic->regs + INTRPT_SIG_EN); | |
| } | |
| static irqreturn_t mxic_ecc_isr(int irq, void *dev_id) | |
| { | |
| struct mxic_ecc_engine *mxic = dev_id; | |
| u32 sts; | |
| sts = readl(mxic->regs + INTRPT_STS); | |
| if (!sts) | |
| return IRQ_NONE; | |
| if (sts & TRANS_CMPLT) | |
| complete(&mxic->complete); | |
| writel(sts, mxic->regs + INTRPT_STS); | |
| return IRQ_HANDLED; | |
| } | |
| static int mxic_ecc_init_ctx(struct nand_device *nand, struct device *dev) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct nand_ecc_props *conf = &nand->ecc.ctx.conf; | |
| struct nand_ecc_props *reqs = &nand->ecc.requirements; | |
| struct nand_ecc_props *user = &nand->ecc.user_conf; | |
| struct mtd_info *mtd = nanddev_to_mtd(nand); | |
| int step_size = 0, strength = 0, desired_correction = 0, steps, idx; | |
| static const int possible_strength[] = {4, 8, 40, 48}; | |
| static const int spare_size[] = {32, 32, 96, 96}; | |
| struct mxic_ecc_ctx *ctx; | |
| u32 spare_reg; | |
| int ret; | |
| ctx = devm_kzalloc_obj(dev, *ctx); | |
| if (!ctx) | |
| return -ENOMEM; | |
| nand->ecc.ctx.priv = ctx; | |
| /* Only large page NAND chips may use BCH */ | |
| if (mtd->oobsize < 64) { | |
| pr_err("BCH cannot be used with small page NAND chips\n"); | |
| return -EINVAL; | |
| } | |
| mtd_set_ooblayout(mtd, &mxic_ecc_ooblayout_ops); | |
| /* Enable all status bits */ | |
| writel(TRANS_CMPLT | SDMA_MAIN | SDMA_SPARE | ECC_ERR | | |
| TO_SPARE | TO_MAIN, mxic->regs + INTRPT_STS_EN); | |
| /* Configure the correction depending on the NAND device topology */ | |
| if (user->step_size && user->strength) { | |
| step_size = user->step_size; | |
| strength = user->strength; | |
| } else if (reqs->step_size && reqs->strength) { | |
| step_size = reqs->step_size; | |
| strength = reqs->strength; | |
| } | |
| if (step_size && strength) { | |
| steps = mtd->writesize / step_size; | |
| desired_correction = steps * strength; | |
| } | |
| /* Step size is fixed to 1kiB, strength may vary (4 possible values) */ | |
| conf->step_size = SZ_1K; | |
| steps = mtd->writesize / conf->step_size; | |
| ctx->status = devm_kzalloc(dev, steps * sizeof(u8), GFP_KERNEL); | |
| if (!ctx->status) | |
| return -ENOMEM; | |
| if (desired_correction) { | |
| strength = desired_correction / steps; | |
| for (idx = 0; idx < ARRAY_SIZE(possible_strength); idx++) | |
| if (possible_strength[idx] >= strength) | |
| break; | |
| idx = min_t(unsigned int, idx, | |
| ARRAY_SIZE(possible_strength) - 1); | |
| } else { | |
| /* Missing data, maximize the correction */ | |
| idx = ARRAY_SIZE(possible_strength) - 1; | |
| } | |
| /* Tune the selected strength until it fits in the OOB area */ | |
| for (; idx >= 0; idx--) { | |
| if (spare_size[idx] * steps <= mtd->oobsize) | |
| break; | |
| } | |
| /* This engine cannot be used with this NAND device */ | |
| if (idx < 0) | |
| return -EINVAL; | |
| /* Configure the engine for the desired strength */ | |
| writel(ECC_TYP(idx), mxic->regs + DP_CONFIG); | |
| conf->strength = possible_strength[idx]; | |
| spare_reg = readl(mxic->regs + SPARE_SIZE); | |
| ctx->steps = steps; | |
| ctx->data_step_sz = mtd->writesize / steps; | |
| ctx->oob_step_sz = mtd->oobsize / steps; | |
| ctx->parity_sz = PARITY_SZ(spare_reg); | |
| ctx->meta_sz = META_SZ(spare_reg); | |
| /* Ensure buffers will contain enough bytes to store the STAT_BYTES */ | |
| ctx->req_ctx.oob_buffer_size = nanddev_per_page_oobsize(nand) + | |
| (ctx->steps * STAT_BYTES); | |
| ret = nand_ecc_init_req_tweaking(&ctx->req_ctx, nand); | |
| if (ret) | |
| return ret; | |
| ctx->oobwithstat = kmalloc(mtd->oobsize + (ctx->steps * STAT_BYTES), | |
| GFP_KERNEL); | |
| if (!ctx->oobwithstat) { | |
| ret = -ENOMEM; | |
| goto cleanup_req_tweak; | |
| } | |
| sg_init_table(ctx->sg, 2); | |
| /* Configuration dump and sanity checks */ | |
| dev_dbg(dev, "DPE version number: %d\n", | |
| readl(mxic->regs + DP_VER) >> DP_VER_OFFSET); | |
| dev_dbg(dev, "Chunk size: %d\n", readl(mxic->regs + CHUNK_SIZE)); | |
| dev_dbg(dev, "Main size: %d\n", readl(mxic->regs + MAIN_SIZE)); | |
| dev_dbg(dev, "Spare size: %d\n", SPARE_SZ(spare_reg)); | |
| dev_dbg(dev, "Rsv size: %ld\n", RSV_SZ(spare_reg)); | |
| dev_dbg(dev, "Parity size: %d\n", ctx->parity_sz); | |
| dev_dbg(dev, "Meta size: %d\n", ctx->meta_sz); | |
| if ((ctx->meta_sz + ctx->parity_sz + RSV_SZ(spare_reg)) != | |
| SPARE_SZ(spare_reg)) { | |
| dev_err(dev, "Wrong OOB configuration: %d + %d + %ld != %d\n", | |
| ctx->meta_sz, ctx->parity_sz, RSV_SZ(spare_reg), | |
| SPARE_SZ(spare_reg)); | |
| ret = -EINVAL; | |
| goto free_oobwithstat; | |
| } | |
| if (ctx->oob_step_sz != SPARE_SZ(spare_reg)) { | |
| dev_err(dev, "Wrong OOB configuration: %d != %d\n", | |
| ctx->oob_step_sz, SPARE_SZ(spare_reg)); | |
| ret = -EINVAL; | |
| goto free_oobwithstat; | |
| } | |
| return 0; | |
| free_oobwithstat: | |
| kfree(ctx->oobwithstat); | |
| cleanup_req_tweak: | |
| nand_ecc_cleanup_req_tweaking(&ctx->req_ctx); | |
| return ret; | |
| } | |
| static int mxic_ecc_init_ctx_external(struct nand_device *nand) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct device *dev = nand->ecc.engine->dev; | |
| int ret; | |
| dev_info(dev, "Macronix ECC engine in external mode\n"); | |
| ret = mxic_ecc_init_ctx(nand, dev); | |
| if (ret) | |
| return ret; | |
| /* Trigger each step manually */ | |
| writel(1, mxic->regs + CHUNK_CNT); | |
| writel(BURST_TYP_INCREASING | ECC_PACKED | MEM2MEM, | |
| mxic->regs + HC_CONFIG); | |
| return 0; | |
| } | |
| static int mxic_ecc_init_ctx_pipelined(struct nand_device *nand) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct mxic_ecc_ctx *ctx; | |
| struct device *dev; | |
| int ret; | |
| dev = nand_ecc_get_engine_dev(nand->ecc.engine->dev); | |
| if (!dev) | |
| return -EINVAL; | |
| dev_info(dev, "Macronix ECC engine in pipelined/mapping mode\n"); | |
| ret = mxic_ecc_init_ctx(nand, dev); | |
| if (ret) | |
| return ret; | |
| ctx = nand_to_ecc_ctx(nand); | |
| /* All steps should be handled in one go directly by the internal DMA */ | |
| writel(ctx->steps, mxic->regs + CHUNK_CNT); | |
| /* | |
| * Interleaved ECC scheme cannot be used otherwise factory bad block | |
| * markers would be lost. A packed layout is mandatory. | |
| */ | |
| writel(BURST_TYP_INCREASING | ECC_PACKED | MAPPING, | |
| mxic->regs + HC_CONFIG); | |
| return 0; | |
| } | |
| static void mxic_ecc_cleanup_ctx(struct nand_device *nand) | |
| { | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| if (ctx) { | |
| nand_ecc_cleanup_req_tweaking(&ctx->req_ctx); | |
| kfree(ctx->oobwithstat); | |
| } | |
| } | |
| static int mxic_ecc_data_xfer_wait_for_completion(struct mxic_ecc_engine *mxic) | |
| { | |
| u32 val; | |
| int ret; | |
| if (mxic->irq) { | |
| reinit_completion(&mxic->complete); | |
| mxic_ecc_enable_int(mxic); | |
| ret = wait_for_completion_timeout(&mxic->complete, | |
| msecs_to_jiffies(1000)); | |
| ret = ret ? 0 : -ETIMEDOUT; | |
| mxic_ecc_disable_int(mxic); | |
| } else { | |
| ret = readl_poll_timeout(mxic->regs + INTRPT_STS, val, | |
| val & TRANS_CMPLT, 10, USEC_PER_SEC); | |
| writel(val, mxic->regs + INTRPT_STS); | |
| } | |
| if (ret) { | |
| dev_err(mxic->dev, "Timeout on data xfer completion\n"); | |
| return -ETIMEDOUT; | |
| } | |
| return 0; | |
| } | |
| static int mxic_ecc_process_data(struct mxic_ecc_engine *mxic, | |
| unsigned int direction) | |
| { | |
| unsigned int dir = (direction == NAND_PAGE_READ) ? | |
| READ_NAND : WRITE_NAND; | |
| int ret; | |
| mxic_ecc_enable_engine(mxic); | |
| /* Trigger processing */ | |
| writel(SDMA_STRT | dir, mxic->regs + SDMA_CTRL); | |
| /* Wait for completion */ | |
| ret = mxic_ecc_data_xfer_wait_for_completion(mxic); | |
| mxic_ecc_disable_engine(mxic); | |
| return ret; | |
| } | |
| int mxic_ecc_process_data_pipelined(struct nand_ecc_engine *eng, | |
| unsigned int direction, dma_addr_t dirmap) | |
| { | |
| struct mxic_ecc_engine *mxic = pip_ecc_eng_to_mxic(eng); | |
| if (dirmap) | |
| writel(dirmap, mxic->regs + HC_SLV_ADDR); | |
| return mxic_ecc_process_data(mxic, direction); | |
| } | |
| EXPORT_SYMBOL_GPL(mxic_ecc_process_data_pipelined); | |
| static void mxic_ecc_extract_status_bytes(struct mxic_ecc_ctx *ctx) | |
| { | |
| u8 *buf = ctx->oobwithstat; | |
| int next_stat_pos; | |
| int step; | |
| /* Extract the ECC status */ | |
| for (step = 0; step < ctx->steps; step++) { | |
| next_stat_pos = ctx->oob_step_sz + | |
| ((STAT_BYTES + ctx->oob_step_sz) * step); | |
| ctx->status[step] = buf[next_stat_pos]; | |
| } | |
| } | |
| static void mxic_ecc_reconstruct_oobbuf(struct mxic_ecc_ctx *ctx, | |
| u8 *dst, const u8 *src) | |
| { | |
| int step; | |
| /* Reconstruct the OOB buffer linearly (without the ECC status bytes) */ | |
| for (step = 0; step < ctx->steps; step++) | |
| memcpy(dst + (step * ctx->oob_step_sz), | |
| src + (step * (ctx->oob_step_sz + STAT_BYTES)), | |
| ctx->oob_step_sz); | |
| } | |
| static void mxic_ecc_add_room_in_oobbuf(struct mxic_ecc_ctx *ctx, | |
| u8 *dst, const u8 *src) | |
| { | |
| int step; | |
| /* Add some space in the OOB buffer for the status bytes */ | |
| for (step = 0; step < ctx->steps; step++) | |
| memcpy(dst + (step * (ctx->oob_step_sz + STAT_BYTES)), | |
| src + (step * ctx->oob_step_sz), | |
| ctx->oob_step_sz); | |
| } | |
| static int mxic_ecc_count_biterrs(struct mxic_ecc_engine *mxic, | |
| struct nand_device *nand) | |
| { | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| struct mtd_info *mtd = nanddev_to_mtd(nand); | |
| struct device *dev = mxic->dev; | |
| unsigned int max_bf = 0; | |
| bool failure = false; | |
| int step; | |
| for (step = 0; step < ctx->steps; step++) { | |
| u8 stat = ctx->status[step]; | |
| if (stat == NO_ERR) { | |
| dev_dbg(dev, "ECC step %d: no error\n", step); | |
| } else if (stat == ERASED_CHUNK) { | |
| dev_dbg(dev, "ECC step %d: erased\n", step); | |
| } else if (stat == UNCORR_ERR || stat > MAX_CORR_ERR) { | |
| dev_dbg(dev, "ECC step %d: uncorrectable\n", step); | |
| mtd->ecc_stats.failed++; | |
| failure = true; | |
| } else { | |
| dev_dbg(dev, "ECC step %d: %d bits corrected\n", | |
| step, stat); | |
| max_bf = max_t(unsigned int, max_bf, stat); | |
| mtd->ecc_stats.corrected += stat; | |
| } | |
| } | |
| return failure ? -EBADMSG : max_bf; | |
| } | |
| /* External ECC engine helpers */ | |
| static int mxic_ecc_prepare_io_req_external(struct nand_device *nand, | |
| struct nand_page_io_req *req) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| struct mtd_info *mtd = nanddev_to_mtd(nand); | |
| int offset, nents, step, ret; | |
| if (req->mode == MTD_OPS_RAW) | |
| return 0; | |
| nand_ecc_tweak_req(&ctx->req_ctx, req); | |
| ctx->req = req; | |
| if (req->type == NAND_PAGE_READ) | |
| return 0; | |
| mxic_ecc_add_room_in_oobbuf(ctx, ctx->oobwithstat, | |
| ctx->req->oobbuf.out); | |
| sg_set_buf(&ctx->sg[0], req->databuf.out, req->datalen); | |
| sg_set_buf(&ctx->sg[1], ctx->oobwithstat, | |
| req->ooblen + (ctx->steps * STAT_BYTES)); | |
| nents = dma_map_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (!nents) | |
| return -EINVAL; | |
| mutex_lock(&mxic->lock); | |
| for (step = 0; step < ctx->steps; step++) { | |
| writel(sg_dma_address(&ctx->sg[0]) + (step * ctx->data_step_sz), | |
| mxic->regs + SDMA_MAIN_ADDR); | |
| writel(sg_dma_address(&ctx->sg[1]) + (step * (ctx->oob_step_sz + STAT_BYTES)), | |
| mxic->regs + SDMA_SPARE_ADDR); | |
| ret = mxic_ecc_process_data(mxic, ctx->req->type); | |
| if (ret) | |
| break; | |
| } | |
| mutex_unlock(&mxic->lock); | |
| dma_unmap_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (ret) | |
| return ret; | |
| /* Retrieve the calculated ECC bytes */ | |
| for (step = 0; step < ctx->steps; step++) { | |
| offset = ctx->meta_sz + (step * ctx->oob_step_sz); | |
| mtd_ooblayout_get_eccbytes(mtd, | |
| (u8 *)ctx->req->oobbuf.out + offset, | |
| ctx->oobwithstat + (step * STAT_BYTES), | |
| step * ctx->parity_sz, | |
| ctx->parity_sz); | |
| } | |
| return 0; | |
| } | |
| static int mxic_ecc_finish_io_req_external(struct nand_device *nand, | |
| struct nand_page_io_req *req) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| int nents, step, ret = 0; | |
| if (req->mode == MTD_OPS_RAW) | |
| return 0; | |
| if (req->type == NAND_PAGE_WRITE) { | |
| nand_ecc_restore_req(&ctx->req_ctx, req); | |
| return 0; | |
| } | |
| /* Copy the OOB buffer and add room for the ECC engine status bytes */ | |
| mxic_ecc_add_room_in_oobbuf(ctx, ctx->oobwithstat, ctx->req->oobbuf.in); | |
| sg_set_buf(&ctx->sg[0], req->databuf.in, req->datalen); | |
| sg_set_buf(&ctx->sg[1], ctx->oobwithstat, | |
| req->ooblen + (ctx->steps * STAT_BYTES)); | |
| nents = dma_map_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (!nents) | |
| return -EINVAL; | |
| mutex_lock(&mxic->lock); | |
| for (step = 0; step < ctx->steps; step++) { | |
| writel(sg_dma_address(&ctx->sg[0]) + (step * ctx->data_step_sz), | |
| mxic->regs + SDMA_MAIN_ADDR); | |
| writel(sg_dma_address(&ctx->sg[1]) + (step * (ctx->oob_step_sz + STAT_BYTES)), | |
| mxic->regs + SDMA_SPARE_ADDR); | |
| ret = mxic_ecc_process_data(mxic, ctx->req->type); | |
| if (ret) | |
| break; | |
| } | |
| mutex_unlock(&mxic->lock); | |
| dma_unmap_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (ret) { | |
| nand_ecc_restore_req(&ctx->req_ctx, req); | |
| return ret; | |
| } | |
| /* Extract the status bytes and reconstruct the buffer */ | |
| mxic_ecc_extract_status_bytes(ctx); | |
| mxic_ecc_reconstruct_oobbuf(ctx, ctx->req->oobbuf.in, ctx->oobwithstat); | |
| nand_ecc_restore_req(&ctx->req_ctx, req); | |
| return mxic_ecc_count_biterrs(mxic, nand); | |
| } | |
| /* Pipelined ECC engine helpers */ | |
| static int mxic_ecc_prepare_io_req_pipelined(struct nand_device *nand, | |
| struct nand_page_io_req *req) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| int nents; | |
| if (req->mode == MTD_OPS_RAW) | |
| return 0; | |
| nand_ecc_tweak_req(&ctx->req_ctx, req); | |
| ctx->req = req; | |
| /* Copy the OOB buffer and add room for the ECC engine status bytes */ | |
| mxic_ecc_add_room_in_oobbuf(ctx, ctx->oobwithstat, ctx->req->oobbuf.in); | |
| sg_set_buf(&ctx->sg[0], req->databuf.in, req->datalen); | |
| sg_set_buf(&ctx->sg[1], ctx->oobwithstat, | |
| req->ooblen + (ctx->steps * STAT_BYTES)); | |
| nents = dma_map_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (!nents) | |
| return -EINVAL; | |
| mutex_lock(&mxic->lock); | |
| writel(sg_dma_address(&ctx->sg[0]), mxic->regs + SDMA_MAIN_ADDR); | |
| writel(sg_dma_address(&ctx->sg[1]), mxic->regs + SDMA_SPARE_ADDR); | |
| return 0; | |
| } | |
| static int mxic_ecc_finish_io_req_pipelined(struct nand_device *nand, | |
| struct nand_page_io_req *req) | |
| { | |
| struct mxic_ecc_engine *mxic = nand_to_mxic(nand); | |
| struct mxic_ecc_ctx *ctx = nand_to_ecc_ctx(nand); | |
| int ret = 0; | |
| if (req->mode == MTD_OPS_RAW) | |
| return 0; | |
| mutex_unlock(&mxic->lock); | |
| dma_unmap_sg(mxic->dev, ctx->sg, 2, DMA_BIDIRECTIONAL); | |
| if (req->type == NAND_PAGE_READ) { | |
| mxic_ecc_extract_status_bytes(ctx); | |
| mxic_ecc_reconstruct_oobbuf(ctx, ctx->req->oobbuf.in, | |
| ctx->oobwithstat); | |
| ret = mxic_ecc_count_biterrs(mxic, nand); | |
| } | |
| nand_ecc_restore_req(&ctx->req_ctx, req); | |
| return ret; | |
| } | |
| static const struct nand_ecc_engine_ops mxic_ecc_engine_external_ops = { | |
| .init_ctx = mxic_ecc_init_ctx_external, | |
| .cleanup_ctx = mxic_ecc_cleanup_ctx, | |
| .prepare_io_req = mxic_ecc_prepare_io_req_external, | |
| .finish_io_req = mxic_ecc_finish_io_req_external, | |
| }; | |
| static const struct nand_ecc_engine_ops mxic_ecc_engine_pipelined_ops = { | |
| .init_ctx = mxic_ecc_init_ctx_pipelined, | |
| .cleanup_ctx = mxic_ecc_cleanup_ctx, | |
| .prepare_io_req = mxic_ecc_prepare_io_req_pipelined, | |
| .finish_io_req = mxic_ecc_finish_io_req_pipelined, | |
| }; | |
| const struct nand_ecc_engine_ops *mxic_ecc_get_pipelined_ops(void) | |
| { | |
| return &mxic_ecc_engine_pipelined_ops; | |
| } | |
| EXPORT_SYMBOL_GPL(mxic_ecc_get_pipelined_ops); | |
| static struct platform_device * | |
| mxic_ecc_get_pdev(struct platform_device *spi_pdev) | |
| { | |
| struct platform_device *eng_pdev; | |
| struct device_node *np; | |
| /* Retrieve the nand-ecc-engine phandle */ | |
| np = of_parse_phandle(spi_pdev->dev.of_node, "nand-ecc-engine", 0); | |
| if (!np) | |
| return NULL; | |
| /* Jump to the engine's device node */ | |
| eng_pdev = of_find_device_by_node(np); | |
| of_node_put(np); | |
| return eng_pdev; | |
| } | |
| void mxic_ecc_put_pipelined_engine(struct nand_ecc_engine *eng) | |
| { | |
| struct mxic_ecc_engine *mxic = pip_ecc_eng_to_mxic(eng); | |
| platform_device_put(to_platform_device(mxic->dev)); | |
| } | |
| EXPORT_SYMBOL_GPL(mxic_ecc_put_pipelined_engine); | |
| struct nand_ecc_engine * | |
| mxic_ecc_get_pipelined_engine(struct platform_device *spi_pdev) | |
| { | |
| struct platform_device *eng_pdev; | |
| struct mxic_ecc_engine *mxic; | |
| eng_pdev = mxic_ecc_get_pdev(spi_pdev); | |
| if (!eng_pdev) | |
| return ERR_PTR(-ENODEV); | |
| mxic = platform_get_drvdata(eng_pdev); | |
| if (!mxic) { | |
| platform_device_put(eng_pdev); | |
| return ERR_PTR(-EPROBE_DEFER); | |
| } | |
| return &mxic->pipelined_engine; | |
| } | |
| EXPORT_SYMBOL_GPL(mxic_ecc_get_pipelined_engine); | |
| /* | |
| * Only the external ECC engine is exported as the pipelined is SoC specific, so | |
| * it is registered directly by the drivers that wrap it. | |
| */ | |
| static int mxic_ecc_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| struct mxic_ecc_engine *mxic; | |
| int ret; | |
| mxic = devm_kzalloc_obj(&pdev->dev, *mxic); | |
| if (!mxic) | |
| return -ENOMEM; | |
| mxic->dev = &pdev->dev; | |
| /* | |
| * Both memory regions for the ECC engine itself and the AXI slave | |
| * address are mandatory. | |
| */ | |
| mxic->regs = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(mxic->regs)) { | |
| dev_err(&pdev->dev, "Missing memory region\n"); | |
| return PTR_ERR(mxic->regs); | |
| } | |
| mxic_ecc_disable_engine(mxic); | |
| mxic_ecc_disable_int(mxic); | |
| /* IRQ is optional yet much more efficient */ | |
| mxic->irq = platform_get_irq_byname_optional(pdev, "ecc-engine"); | |
| if (mxic->irq > 0) { | |
| ret = devm_request_irq(&pdev->dev, mxic->irq, mxic_ecc_isr, 0, | |
| "mxic-ecc", mxic); | |
| if (ret) | |
| return ret; | |
| } else { | |
| dev_info(dev, "Invalid or missing IRQ, fallback to polling\n"); | |
| mxic->irq = 0; | |
| } | |
| mutex_init(&mxic->lock); | |
| /* | |
| * In external mode, the device is the ECC engine. In pipelined mode, | |
| * the device is the host controller. The device is used to match the | |
| * right ECC engine based on the DT properties. | |
| */ | |
| mxic->external_engine.dev = &pdev->dev; | |
| mxic->external_engine.integration = NAND_ECC_ENGINE_INTEGRATION_EXTERNAL; | |
| mxic->external_engine.ops = &mxic_ecc_engine_external_ops; | |
| nand_ecc_register_on_host_hw_engine(&mxic->external_engine); | |
| platform_set_drvdata(pdev, mxic); | |
| return 0; | |
| } | |
| static void mxic_ecc_remove(struct platform_device *pdev) | |
| { | |
| struct mxic_ecc_engine *mxic = platform_get_drvdata(pdev); | |
| nand_ecc_unregister_on_host_hw_engine(&mxic->external_engine); | |
| } | |
| static const struct of_device_id mxic_ecc_of_ids[] = { | |
| { | |
| .compatible = "mxicy,nand-ecc-engine-rev3", | |
| }, | |
| { /* sentinel */ }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, mxic_ecc_of_ids); | |
| static struct platform_driver mxic_ecc_driver = { | |
| .driver = { | |
| .name = "mxic-nand-ecc-engine", | |
| .of_match_table = mxic_ecc_of_ids, | |
| }, | |
| .probe = mxic_ecc_probe, | |
| .remove = mxic_ecc_remove, | |
| }; | |
| module_platform_driver(mxic_ecc_driver); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>"); | |
| MODULE_DESCRIPTION("Macronix NAND hardware ECC controller"); |