| // SPDX-License-Identifier: BSD-3-Clause | |
| /* | |
| * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. | |
| */ | |
| /dts-v1/; | |
| #include <dt-bindings/gpio/gpio.h> | |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> | |
| #include "hamoa.dtsi" | |
| #include "hamoa-pmics.dtsi" | |
| / { | |
| model = "Qualcomm Technologies, Inc. X1E001DE Snapdragon Devkit for Windows"; | |
| compatible = "qcom,x1e001de-devkit", "qcom,x1e001de", "qcom,x1e80100"; | |
| aliases { | |
| serial0 = &uart21; | |
| }; | |
| wcd938x: audio-codec { | |
| compatible = "qcom,wcd9385-codec"; | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&wcd_default>; | |
| qcom,micbias1-microvolt = <1800000>; | |
| qcom,micbias2-microvolt = <1800000>; | |
| qcom,micbias3-microvolt = <1800000>; | |
| qcom,micbias4-microvolt = <1800000>; | |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; | |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; | |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; | |
| qcom,rx-device = <&wcd_rx>; | |
| qcom,tx-device = <&wcd_tx>; | |
| reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; | |
| vdd-buck-supply = <&vreg_l15b_1p8>; | |
| vdd-rxtx-supply = <&vreg_l15b_1p8>; | |
| vdd-io-supply = <&vreg_l15b_1p8>; | |
| vdd-mic-bias-supply = <&vreg_bob1>; | |
| #sound-dai-cells = <1>; | |
| }; | |
| chosen { | |
| stdout-path = "serial0:115200n8"; | |
| }; | |
| pmic-glink { | |
| compatible = "qcom,x1e80100-pmic-glink", | |
| "qcom,sm8550-pmic-glink", | |
| "qcom,pmic-glink"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, | |
| <&tlmm 123 GPIO_ACTIVE_HIGH>, | |
| <&tlmm 125 GPIO_ACTIVE_HIGH>; | |
| /* Back panel port closer to the RJ45 connector */ | |
| connector@0 { | |
| compatible = "usb-c-connector"; | |
| reg = <0>; | |
| power-role = "dual"; | |
| data-role = "dual"; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| pmic_glink_ss0_hs_in: endpoint { | |
| remote-endpoint = <&usb_1_ss0_dwc3_hs>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| pmic_glink_ss0_ss_in: endpoint { | |
| remote-endpoint = <&retimer_ss0_ss_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| pmic_glink_ss0_con_sbu_in: endpoint { | |
| remote-endpoint = <&retimer_ss0_con_sbu_out>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| /* Back panel port closer to the audio jack */ | |
| connector@1 { | |
| compatible = "usb-c-connector"; | |
| reg = <1>; | |
| power-role = "dual"; | |
| data-role = "host"; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| pmic_glink_ss1_hs_in: endpoint { | |
| remote-endpoint = <&usb_1_ss1_dwc3_hs>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| pmic_glink_ss1_ss_in: endpoint { | |
| remote-endpoint = <&retimer_ss1_ss_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| pmic_glink_ss1_con_sbu_in: endpoint { | |
| remote-endpoint = <&retimer_ss1_con_sbu_out>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| /* Front panel port */ | |
| connector@2 { | |
| compatible = "usb-c-connector"; | |
| reg = <2>; | |
| power-role = "dual"; | |
| data-role = "host"; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| pmic_glink_ss2_hs_in: endpoint { | |
| remote-endpoint = <&usb_1_ss2_dwc3_hs>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| pmic_glink_ss2_ss_in: endpoint { | |
| remote-endpoint = <&retimer_ss2_ss_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| pmic_glink_ss2_con_sbu_in: endpoint { | |
| remote-endpoint = <&retimer_ss2_con_sbu_out>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| reserved-memory { | |
| linux,cma { | |
| compatible = "shared-dma-pool"; | |
| size = <0x0 0x8000000>; | |
| reusable; | |
| linux,cma-default; | |
| }; | |
| }; | |
| sound { | |
| compatible = "qcom,x1e80100-sndcard"; | |
| model = "X1E001DE-DEVKIT"; | |
| audio-routing = "IN1_HPHL", "HPHL_OUT", | |
| "IN2_HPHR", "HPHR_OUT", | |
| "AMIC2", "MIC BIAS2", | |
| "TX SWR_INPUT1", "ADC2_OUTPUT"; | |
| wcd-playback-dai-link { | |
| link-name = "WCD Playback"; | |
| cpu { | |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; | |
| }; | |
| codec { | |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; | |
| }; | |
| platform { | |
| sound-dai = <&q6apm>; | |
| }; | |
| }; | |
| wcd-capture-dai-link { | |
| link-name = "WCD Capture"; | |
| cpu { | |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; | |
| }; | |
| codec { | |
| sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>; | |
| }; | |
| platform { | |
| sound-dai = <&q6apm>; | |
| }; | |
| }; | |
| }; | |
| vreg_nvme: regulator-nvme { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_NVME_3P3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&nvme_reg_en>; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr0_1p15: regulator-rtmr0-1p15 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR0_1P15"; | |
| regulator-min-microvolt = <1150000>; | |
| regulator-max-microvolt = <1150000>; | |
| gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&usb0_pwr_1p15_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr0_1p8: regulator-rtmr0-1p8 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR0_1P8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&usb0_1p8_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr0_3p3: regulator-rtmr0-3p3 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR0_3P3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&usb0_3p3_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr1_1p15: regulator-rtmr1-1p15 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR1_1P15"; | |
| regulator-min-microvolt = <1150000>; | |
| regulator-max-microvolt = <1150000>; | |
| gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr1_1p15_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr1_1p8: regulator-rtmr1-1p8 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR1_1P8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr1_1p8_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr1_3p3: regulator-rtmr1-3p3 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR1_3P3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr1_3p3_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr2_1p15: regulator-rtmr2-1p15 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR2_1P15"; | |
| regulator-min-microvolt = <1150000>; | |
| regulator-max-microvolt = <1150000>; | |
| gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr2_1p15_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr2_1p8: regulator-rtmr2-1p8 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR2_1P8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr2_1p8_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vreg_rtmr2_3p3: regulator-rtmr2-3p3 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VREG_RTMR2_3P3"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&rtmr2_3p3_reg_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| vph_pwr: regulator-vph-pwr { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "vph_pwr"; | |
| regulator-min-microvolt = <3700000>; | |
| regulator-max-microvolt = <3700000>; | |
| regulator-always-on; | |
| regulator-boot-on; | |
| }; | |
| vreg_wwan: regulator-wwan { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "SDX_VPH_PWR"; | |
| regulator-min-microvolt = <3300000>; | |
| regulator-max-microvolt = <3300000>; | |
| gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>; | |
| enable-active-high; | |
| pinctrl-0 = <&wwan_sw_en>; | |
| pinctrl-names = "default"; | |
| regulator-boot-on; | |
| }; | |
| }; | |
| &apps_rsc { | |
| regulators-0 { | |
| compatible = "qcom,pm8550-rpmh-regulators"; | |
| qcom,pmic-id = "b"; | |
| vdd-bob1-supply = <&vph_pwr>; | |
| vdd-bob2-supply = <&vph_pwr>; | |
| vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; | |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; | |
| vdd-l5-l16-supply = <&vreg_bob1>; | |
| vdd-l6-l7-supply = <&vreg_bob2>; | |
| vdd-l8-l9-supply = <&vreg_bob1>; | |
| vdd-l12-supply = <&vreg_s5j_1p2>; | |
| vdd-l15-supply = <&vreg_s4c_1p8>; | |
| vdd-l17-supply = <&vreg_bob2>; | |
| vreg_bob1: bob1 { | |
| regulator-name = "vreg_bob1"; | |
| regulator-min-microvolt = <3008000>; | |
| regulator-max-microvolt = <3960000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_bob2: bob2 { | |
| regulator-name = "vreg_bob2"; | |
| regulator-min-microvolt = <2504000>; | |
| regulator-max-microvolt = <3008000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l1b_1p8: ldo1 { | |
| regulator-name = "vreg_l1b_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2b_3p0: ldo2 { | |
| regulator-name = "vreg_l2b_3p0"; | |
| regulator-min-microvolt = <3072000>; | |
| regulator-max-microvolt = <3100000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l4b_1p8: ldo4 { | |
| regulator-name = "vreg_l4b_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l5b_3p0: ldo5 { | |
| regulator-name = "vreg_l5b_3p0"; | |
| regulator-min-microvolt = <3000000>; | |
| regulator-max-microvolt = <3000000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l6b_1p8: ldo6 { | |
| regulator-name = "vreg_l6b_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <2960000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l7b_2p8: ldo7 { | |
| regulator-name = "vreg_l7b_2p8"; | |
| regulator-min-microvolt = <2800000>; | |
| regulator-max-microvolt = <2800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l8b_3p0: ldo8 { | |
| regulator-name = "vreg_l8b_3p0"; | |
| regulator-min-microvolt = <3072000>; | |
| regulator-max-microvolt = <3072000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l9b_2p9: ldo9 { | |
| regulator-name = "vreg_l9b_2p9"; | |
| regulator-min-microvolt = <2960000>; | |
| regulator-max-microvolt = <2960000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l10b_1p8: ldo10 { | |
| regulator-name = "vreg_l10b_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l12b_1p2: ldo12 { | |
| regulator-name = "vreg_l12b_1p2"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1200000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| regulator-always-on; | |
| }; | |
| vreg_l13b_3p0: ldo13 { | |
| regulator-name = "vreg_l13b_3p0"; | |
| regulator-min-microvolt = <3072000>; | |
| regulator-max-microvolt = <3100000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l14b_3p0: ldo14 { | |
| regulator-name = "vreg_l14b_3p0"; | |
| regulator-min-microvolt = <3072000>; | |
| regulator-max-microvolt = <3072000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l15b_1p8: ldo15 { | |
| regulator-name = "vreg_l15b_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| regulator-always-on; | |
| }; | |
| vreg_l16b_2p9: ldo16 { | |
| regulator-name = "vreg_l16b_2p9"; | |
| regulator-min-microvolt = <2912000>; | |
| regulator-max-microvolt = <2912000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l17b_2p5: ldo17 { | |
| regulator-name = "vreg_l17b_2p5"; | |
| regulator-min-microvolt = <2504000>; | |
| regulator-max-microvolt = <2504000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-1 { | |
| compatible = "qcom,pm8550ve-rpmh-regulators"; | |
| qcom,pmic-id = "c"; | |
| vdd-l1-supply = <&vreg_s5j_1p2>; | |
| vdd-l2-supply = <&vreg_s1f_0p7>; | |
| vdd-l3-supply = <&vreg_s1f_0p7>; | |
| vdd-s4-supply = <&vph_pwr>; | |
| vreg_s4c_1p8: smps4 { | |
| regulator-name = "vreg_s4c_1p8"; | |
| regulator-min-microvolt = <1856000>; | |
| regulator-max-microvolt = <2000000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l1c_1p2: ldo1 { | |
| regulator-name = "vreg_l1c_1p2"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1200000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2c_0p8: ldo2 { | |
| regulator-name = "vreg_l2c_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3c_0p8: ldo3 { | |
| regulator-name = "vreg_l3c_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-2 { | |
| compatible = "qcom,pmc8380-rpmh-regulators"; | |
| qcom,pmic-id = "d"; | |
| vdd-l1-supply = <&vreg_s1f_0p7>; | |
| vdd-l2-supply = <&vreg_s1f_0p7>; | |
| vdd-l3-supply = <&vreg_s4c_1p8>; | |
| vdd-s1-supply = <&vph_pwr>; | |
| vreg_l1d_0p8: ldo1 { | |
| regulator-name = "vreg_l1d_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2d_0p9: ldo2 { | |
| regulator-name = "vreg_l2d_0p9"; | |
| regulator-min-microvolt = <912000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3d_1p8: ldo3 { | |
| regulator-name = "vreg_l3d_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-3 { | |
| compatible = "qcom,pmc8380-rpmh-regulators"; | |
| qcom,pmic-id = "e"; | |
| vdd-l2-supply = <&vreg_s1f_0p7>; | |
| vdd-l3-supply = <&vreg_s5j_1p2>; | |
| vreg_l2e_0p8: ldo2 { | |
| regulator-name = "vreg_l2e_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3e_1p2: ldo3 { | |
| regulator-name = "vreg_l3e_1p2"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1200000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-4 { | |
| compatible = "qcom,pmc8380-rpmh-regulators"; | |
| qcom,pmic-id = "f"; | |
| vdd-l1-supply = <&vreg_s5j_1p2>; | |
| vdd-l2-supply = <&vreg_s5j_1p2>; | |
| vdd-l3-supply = <&vreg_s5j_1p2>; | |
| vdd-s1-supply = <&vph_pwr>; | |
| vreg_s1f_0p7: smps1 { | |
| regulator-name = "vreg_s1f_0p7"; | |
| regulator-min-microvolt = <700000>; | |
| regulator-max-microvolt = <1100000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l1f_1p0: ldo1 { | |
| regulator-name = "vreg_l1f_1p0"; | |
| regulator-min-microvolt = <1024000>; | |
| regulator-max-microvolt = <1024000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2f_1p0: ldo2 { | |
| regulator-name = "vreg_l2f_1p0"; | |
| regulator-min-microvolt = <1024000>; | |
| regulator-max-microvolt = <1024000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3f_1p0: ldo3 { | |
| regulator-name = "vreg_l3f_1p0"; | |
| regulator-min-microvolt = <1024000>; | |
| regulator-max-microvolt = <1024000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-6 { | |
| compatible = "qcom,pm8550ve-rpmh-regulators"; | |
| qcom,pmic-id = "i"; | |
| vdd-l1-supply = <&vreg_s4c_1p8>; | |
| vdd-l2-supply = <&vreg_s5j_1p2>; | |
| vdd-l3-supply = <&vreg_s1f_0p7>; | |
| vdd-s1-supply = <&vph_pwr>; | |
| vdd-s2-supply = <&vph_pwr>; | |
| vreg_s1i_0p9: smps1 { | |
| regulator-name = "vreg_s1i_0p9"; | |
| regulator-min-microvolt = <900000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_s2i_1p0: smps2 { | |
| regulator-name = "vreg_s2i_1p0"; | |
| regulator-min-microvolt = <1000000>; | |
| regulator-max-microvolt = <1100000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l1i_1p8: ldo1 { | |
| regulator-name = "vreg_l1i_1p8"; | |
| regulator-min-microvolt = <1800000>; | |
| regulator-max-microvolt = <1800000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2i_1p2: ldo2 { | |
| regulator-name = "vreg_l2i_1p2"; | |
| regulator-min-microvolt = <1200000>; | |
| regulator-max-microvolt = <1200000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3i_0p8: ldo3 { | |
| regulator-name = "vreg_l3i_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| regulators-7 { | |
| compatible = "qcom,pm8550ve-rpmh-regulators"; | |
| qcom,pmic-id = "j"; | |
| vdd-l1-supply = <&vreg_s1f_0p7>; | |
| vdd-l2-supply = <&vreg_s5j_1p2>; | |
| vdd-l3-supply = <&vreg_s1f_0p7>; | |
| vdd-s5-supply = <&vph_pwr>; | |
| vreg_s5j_1p2: smps5 { | |
| regulator-name = "vreg_s5j_1p2"; | |
| regulator-min-microvolt = <1256000>; | |
| regulator-max-microvolt = <1304000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l1j_0p8: ldo1 { | |
| regulator-name = "vreg_l1j_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l2j_1p2: ldo2 { | |
| regulator-name = "vreg_l2j_1p2"; | |
| regulator-min-microvolt = <1256000>; | |
| regulator-max-microvolt = <1256000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| vreg_l3j_0p8: ldo3 { | |
| regulator-name = "vreg_l3j_0p8"; | |
| regulator-min-microvolt = <880000>; | |
| regulator-max-microvolt = <920000>; | |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; | |
| }; | |
| }; | |
| }; | |
| &gpu { | |
| status = "okay"; | |
| }; | |
| &gpu_zap_shader { | |
| firmware-name = "qcom/x1e80100/Thundercomm/DEVKIT/qcdxkmsuc8380.mbn"; | |
| }; | |
| &i2c1 { | |
| clock-frequency = <400000>; | |
| status = "okay"; | |
| typec-mux@8 { | |
| compatible = "parade,ps8830"; | |
| reg = <0x08>; | |
| clocks = <&rpmhcc RPMH_RF_CLK5>; | |
| vdd-supply = <&vreg_rtmr2_1p15>; | |
| vdd33-supply = <&vreg_rtmr2_3p3>; | |
| vdd33-cap-supply = <&vreg_rtmr2_3p3>; | |
| vddar-supply = <&vreg_rtmr2_1p15>; | |
| vddat-supply = <&vreg_rtmr2_1p15>; | |
| vddio-supply = <&vreg_rtmr2_1p8>; | |
| reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&rtmr2_default>; | |
| pinctrl-names = "default"; | |
| orientation-switch; | |
| retimer-switch; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| retimer_ss2_ss_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss2_ss_in>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| retimer_ss2_ss_in: endpoint { | |
| remote-endpoint = <&usb_1_ss2_qmpphy_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| retimer_ss2_con_sbu_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss2_con_sbu_in>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| &i2c3 { | |
| clock-frequency = <400000>; | |
| status = "okay"; | |
| typec-mux@8 { | |
| compatible = "parade,ps8830"; | |
| reg = <0x08>; | |
| clocks = <&rpmhcc RPMH_RF_CLK3>; | |
| vdd-supply = <&vreg_rtmr0_1p15>; | |
| vdd33-supply = <&vreg_rtmr0_3p3>; | |
| vdd33-cap-supply = <&vreg_rtmr0_3p3>; | |
| vddar-supply = <&vreg_rtmr0_1p15>; | |
| vddat-supply = <&vreg_rtmr0_1p15>; | |
| vddio-supply = <&vreg_rtmr0_1p8>; | |
| reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&rtmr0_default>; | |
| pinctrl-names = "default"; | |
| retimer-switch; | |
| orientation-switch; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| retimer_ss0_ss_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss0_ss_in>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| retimer_ss0_ss_in: endpoint { | |
| remote-endpoint = <&usb_1_ss0_qmpphy_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| retimer_ss0_con_sbu_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss0_con_sbu_in>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| &i2c5 { | |
| clock-frequency = <400000>; | |
| status = "okay"; | |
| eusb3_repeater: redriver@47 { | |
| compatible = "nxp,ptn3222"; | |
| reg = <0x47>; | |
| #phy-cells = <0>; | |
| vdd3v3-supply = <&vreg_l13b_3p0>; | |
| vdd1v8-supply = <&vreg_l4b_1p8>; | |
| reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&eusb3_reset_n>; | |
| pinctrl-names = "default"; | |
| }; | |
| eusb6_repeater: redriver@4f { | |
| compatible = "nxp,ptn3222"; | |
| reg = <0x4f>; | |
| #phy-cells = <0>; | |
| vdd3v3-supply = <&vreg_l13b_3p0>; | |
| vdd1v8-supply = <&vreg_l4b_1p8>; | |
| reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&eusb6_reset_n>; | |
| pinctrl-names = "default"; | |
| }; | |
| }; | |
| &i2c7 { | |
| clock-frequency = <400000>; | |
| status = "okay"; | |
| typec-mux@8 { | |
| compatible = "parade,ps8830"; | |
| reg = <0x8>; | |
| clocks = <&rpmhcc RPMH_RF_CLK4>; | |
| vdd-supply = <&vreg_rtmr1_1p15>; | |
| vdd33-supply = <&vreg_rtmr1_3p3>; | |
| vdd33-cap-supply = <&vreg_rtmr1_3p3>; | |
| vddar-supply = <&vreg_rtmr1_1p15>; | |
| vddat-supply = <&vreg_rtmr1_1p15>; | |
| vddio-supply = <&vreg_rtmr1_1p8>; | |
| reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&rtmr1_default>; | |
| pinctrl-names = "default"; | |
| retimer-switch; | |
| orientation-switch; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| retimer_ss1_ss_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss1_ss_in>; | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| retimer_ss1_ss_in: endpoint { | |
| remote-endpoint = <&usb_1_ss1_qmpphy_out>; | |
| }; | |
| }; | |
| port@2 { | |
| reg = <2>; | |
| retimer_ss1_con_sbu_out: endpoint { | |
| remote-endpoint = <&pmic_glink_ss1_con_sbu_in>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| &mdss { | |
| status = "okay"; | |
| }; | |
| &mdss_dp0 { | |
| status = "okay"; | |
| }; | |
| &mdss_dp0_out { | |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; | |
| }; | |
| &mdss_dp1 { | |
| status = "okay"; | |
| }; | |
| &mdss_dp1_out { | |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; | |
| }; | |
| &mdss_dp2 { | |
| status = "okay"; | |
| }; | |
| &mdss_dp2_out { | |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; | |
| }; | |
| &pcie4 { | |
| pinctrl-0 = <&pcie4_default>; | |
| pinctrl-names = "default"; | |
| status = "okay"; | |
| }; | |
| &pcie4_phy { | |
| vdda-phy-supply = <&vreg_l3i_0p8>; | |
| vdda-pll-supply = <&vreg_l3e_1p2>; | |
| status = "okay"; | |
| }; | |
| &pcie4_port0 { | |
| reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; | |
| wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; | |
| }; | |
| &pcie5 { | |
| vddpe-3v3-supply = <&vreg_wwan>; | |
| pinctrl-0 = <&pcie5_default>; | |
| pinctrl-names = "default"; | |
| status = "okay"; | |
| }; | |
| &pcie5_phy { | |
| vdda-phy-supply = <&vreg_l3i_0p8>; | |
| vdda-pll-supply = <&vreg_l3e_1p2>; | |
| status = "okay"; | |
| }; | |
| &pcie5_port0 { | |
| reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>; | |
| wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>; | |
| }; | |
| &pcie6a { | |
| vddpe-3v3-supply = <&vreg_nvme>; | |
| pinctrl-names = "default"; | |
| pinctrl-0 = <&pcie6a_default>; | |
| status = "okay"; | |
| }; | |
| &pcie6a_phy { | |
| vdda-phy-supply = <&vreg_l1d_0p8>; | |
| vdda-pll-supply = <&vreg_l2j_1p2>; | |
| status = "okay"; | |
| }; | |
| &pcie6a_port0 { | |
| reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; | |
| wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; | |
| }; | |
| &pm8550_gpios { | |
| rtmr0_default: rtmr0-reset-n-active-state { | |
| pins = "gpio10"; | |
| function = "normal"; | |
| power-source = <1>; /* 1.8 V */ | |
| bias-disable; | |
| input-disable; | |
| output-enable; | |
| }; | |
| usb0_3p3_reg_en: usb0-3p3-reg-en-state { | |
| pins = "gpio11"; | |
| function = "normal"; | |
| power-source = <1>; /* 1.8 V */ | |
| bias-disable; | |
| input-disable; | |
| output-enable; | |
| }; | |
| }; | |
| &pmc8380_5_gpios { | |
| usb0_pwr_1p15_en: usb0-pwr-1p15-en-state { | |
| pins = "gpio8"; | |
| function = "normal"; | |
| power-source = <1>; /* 1.8 V */ | |
| bias-disable; | |
| input-disable; | |
| output-enable; | |
| }; | |
| }; | |
| &pm8550ve_9_gpios { | |
| usb0_1p8_reg_en: usb0-1p8-reg-en-state { | |
| pins = "gpio8"; | |
| function = "normal"; | |
| power-source = <1>; /* 1.8 V */ | |
| bias-disable; | |
| input-disable; | |
| output-enable; | |
| }; | |
| }; | |
| &qupv3_0 { | |
| status = "okay"; | |
| }; | |
| &qupv3_1 { | |
| status = "okay"; | |
| }; | |
| &qupv3_2 { | |
| status = "okay"; | |
| }; | |
| &remoteproc_adsp { | |
| firmware-name = "qcom/x1e80100/Thundercomm/DEVKIT/qcadsp8380.mbn", | |
| "qcom/x1e80100/Thundercomm/DEVKIT/adsp_dtbs.elf"; | |
| status = "okay"; | |
| }; | |
| &remoteproc_cdsp { | |
| firmware-name = "qcom/x1e80100/Thundercomm/DEVKIT/qccdsp8380.mbn", | |
| "qcom/x1e80100/Thundercomm/DEVKIT/cdsp_dtbs.elf"; | |
| status = "okay"; | |
| }; | |
| &sdhc_2 { | |
| cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>; | |
| pinctrl-0 = <&sdc2_default &sdc2_card_det_n>; | |
| pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>; | |
| pinctrl-names = "default", "sleep"; | |
| vmmc-supply = <&vreg_l9b_2p9>; | |
| vqmmc-supply = <&vreg_l6b_1p8>; | |
| bus-width = <4>; | |
| no-sdio; | |
| no-mmc; | |
| status = "okay"; | |
| }; | |
| &smb2360_0 { | |
| status = "okay"; | |
| }; | |
| &smb2360_0_eusb2_repeater { | |
| vdd18-supply = <&vreg_l3d_1p8>; | |
| vdd3-supply = <&vreg_l2b_3p0>; | |
| }; | |
| &smb2360_1 { | |
| status = "okay"; | |
| }; | |
| &smb2360_1_eusb2_repeater { | |
| vdd18-supply = <&vreg_l3d_1p8>; | |
| vdd3-supply = <&vreg_l14b_3p0>; | |
| }; | |
| &smb2360_2 { | |
| status = "okay"; | |
| }; | |
| &smb2360_2_eusb2_repeater { | |
| vdd18-supply = <&vreg_l3d_1p8>; | |
| vdd3-supply = <&vreg_l8b_3p0>; | |
| }; | |
| &swr1 { | |
| status = "okay"; | |
| /* WCD9385 RX */ | |
| wcd_rx: codec@0,4 { | |
| compatible = "sdw20217010d00"; | |
| reg = <0 4>; | |
| qcom,rx-port-mapping = <1 2 3 4 5>; | |
| }; | |
| }; | |
| &swr2 { | |
| status = "okay"; | |
| /* WCD9385 TX */ | |
| wcd_tx: codec@0,3 { | |
| compatible = "sdw20217010d00"; | |
| reg = <0 3>; | |
| qcom,tx-port-mapping = <2 2 3 4>; | |
| }; | |
| }; | |
| &tcsr { | |
| vdda-qrefrpt0-0p9-supply = <&vreg_l3c_0p8>; | |
| vdda-qrefrpt1-0p9-supply = <&vreg_l3i_0p8>; | |
| vdda-qrefrpt2-0p9-supply = <&vreg_l3i_0p8>; | |
| vdda-qrefrpt3-0p9-supply = <&vreg_l3j_0p8>; | |
| vdda-qrefrpt4-0p9-supply = <&vreg_l1d_0p8>; | |
| vdda-qrefrx0-0p9-supply = <&vreg_l3c_0p8>; | |
| vdda-qrefrx1-0p9-supply = <&vreg_l3i_0p8>; | |
| vdda-qrefrx2-0p9-supply = <&vreg_l3i_0p8>; | |
| vdda-qrefrx3-0p9-supply = <&vreg_l3j_0p8>; | |
| vdda-qrefrx4-0p9-supply = <&vreg_l1d_0p8>; | |
| vdda-qreftx0-0p9-supply = <&vreg_l3j_0p8>; | |
| vdda-qreftx0-1p2-supply = <&vreg_l2j_1p2>; | |
| vdda-qreftx1-0p9-supply = <&vreg_l3j_0p8>; | |
| vdda-qreftx1-1p2-supply = <&vreg_l3e_1p2>; | |
| vdda-refgen0-0p9-supply = <&vreg_l3i_0p8>; | |
| vdda-refgen0-1p2-supply = <&vreg_l3e_1p2>; | |
| vdda-refgen2-0p9-supply = <&vreg_l3j_0p8>; | |
| vdda-refgen2-1p2-supply = <&vreg_l2j_1p2>; | |
| }; | |
| &tlmm { | |
| gpio-reserved-ranges = <44 4>, /* SPI (TPM) */ | |
| <65 1>; /* EC reset */ | |
| eusb3_reset_n: eusb3-reset-n-state { | |
| pins = "gpio6"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| output-low; | |
| }; | |
| eusb6_reset_n: eusb6-reset-n-state { | |
| pins = "gpio184"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| output-low; | |
| }; | |
| nvme_reg_en: nvme-reg-en-state { | |
| pins = "gpio18"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| pcie4_default: pcie4-default-state { | |
| clkreq-n-pins { | |
| pins = "gpio147"; | |
| function = "pcie4_clk"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| perst-n-pins { | |
| pins = "gpio146"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| wake-n-pins { | |
| pins = "gpio148"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| }; | |
| pcie5_default: pcie5-default-state { | |
| clkreq-n-pins { | |
| pins = "gpio150"; | |
| function = "pcie5_clk"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| perst-n-pins { | |
| pins = "gpio149"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| wake-n-pins { | |
| pins = "gpio151"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| }; | |
| pcie6a_default: pcie6a-default-state { | |
| clkreq-n-pins { | |
| pins = "gpio153"; | |
| function = "pcie6a_clk"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| perst-n-pins { | |
| pins = "gpio152"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| wake-n-pins { | |
| pins = "gpio154"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| }; | |
| rtmr1_default: rtmr1-reset-n-active-state { | |
| pins = "gpio176"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr2_default: rtmr2-reset-n-active-state { | |
| pins = "gpio185"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr1_1p15_reg_en: rtmr1-1p15-reg-en-state { | |
| pins = "gpio188"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr1_1p8_reg_en: rtmr1-1p8-reg-en-state { | |
| pins = "gpio175"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr1_3p3_reg_en: rtmr1-3p3-reg-en-state { | |
| pins = "gpio186"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr2_1p15_reg_en: rtmr2-1p15-reg-en-state { | |
| pins = "gpio189"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr2_1p8_reg_en: rtmr2-1p8-reg-en-state { | |
| pins = "gpio126"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| rtmr2_3p3_reg_en: rtmr2-3p3-reg-en-state { | |
| pins = "gpio187"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-disable; | |
| }; | |
| sdc2_card_det_n: sdc2-card-det-state { | |
| pins = "gpio71"; | |
| function = "gpio"; | |
| drive-strength = <2>; | |
| bias-pull-up; | |
| }; | |
| wcd_default: wcd-reset-n-active-state { | |
| pins = "gpio191"; | |
| function = "gpio"; | |
| drive-strength = <16>; | |
| bias-disable; | |
| output-low; | |
| }; | |
| wwan_sw_en: wwan-sw-en-state { | |
| pins = "gpio221"; | |
| function = "gpio"; | |
| drive-strength = <4>; | |
| bias-disable; | |
| }; | |
| }; | |
| &uart21 { | |
| compatible = "qcom,geni-debug-uart"; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss0_hsphy { | |
| vdd-supply = <&vreg_l3j_0p8>; | |
| vdda12-supply = <&vreg_l2j_1p2>; | |
| phys = <&smb2360_0_eusb2_repeater>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss0_qmpphy { | |
| vdda-phy-supply = <&vreg_l1j_0p8>; | |
| vdda-pll-supply = <&vreg_l2j_1p2>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss0 { | |
| dr_mode = "otg"; | |
| usb-role-switch; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss0_dwc3_hs { | |
| remote-endpoint = <&pmic_glink_ss0_hs_in>; | |
| }; | |
| &usb_1_ss0_qmpphy_out { | |
| remote-endpoint = <&retimer_ss0_ss_in>; | |
| }; | |
| &usb_1_ss1_hsphy { | |
| vdd-supply = <&vreg_l3j_0p8>; | |
| vdda12-supply = <&vreg_l2j_1p2>; | |
| phys = <&smb2360_1_eusb2_repeater>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss1_qmpphy { | |
| vdda-phy-supply = <&vreg_l2d_0p9>; | |
| vdda-pll-supply = <&vreg_l2j_1p2>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss1 { | |
| dr_mode = "host"; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss1_dwc3_hs { | |
| remote-endpoint = <&pmic_glink_ss1_hs_in>; | |
| }; | |
| &usb_1_ss1_qmpphy_out { | |
| remote-endpoint = <&retimer_ss1_ss_in>; | |
| }; | |
| &usb_1_ss2_hsphy { | |
| vdd-supply = <&vreg_l3j_0p8>; | |
| vdda12-supply = <&vreg_l2j_1p2>; | |
| phys = <&smb2360_2_eusb2_repeater>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss2_qmpphy { | |
| vdda-phy-supply = <&vreg_l2d_0p9>; | |
| vdda-pll-supply = <&vreg_l2j_1p2>; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss2 { | |
| dr_mode = "host"; | |
| status = "okay"; | |
| }; | |
| &usb_1_ss2_dwc3_hs { | |
| remote-endpoint = <&pmic_glink_ss2_hs_in>; | |
| }; | |
| &usb_1_ss2_qmpphy_out { | |
| remote-endpoint = <&retimer_ss2_ss_in>; | |
| }; | |
| &usb_mp { | |
| status = "okay"; | |
| }; | |
| &usb_mp_hsphy0 { | |
| vdd-supply = <&vreg_l2e_0p8>; | |
| vdda12-supply = <&vreg_l3e_1p2>; | |
| phys = <&eusb3_repeater>; | |
| status = "okay"; | |
| }; | |
| &usb_mp_hsphy1 { | |
| vdd-supply = <&vreg_l2e_0p8>; | |
| vdda12-supply = <&vreg_l3e_1p2>; | |
| phys = <&eusb6_repeater>; | |
| status = "okay"; | |
| }; | |
| &usb_mp_qmpphy0 { | |
| vdda-phy-supply = <&vreg_l3c_0p8>; | |
| vdda-pll-supply = <&vreg_l3e_1p2>; | |
| status = "okay"; | |
| }; | |
| &usb_mp_qmpphy1 { | |
| vdda-phy-supply = <&vreg_l3c_0p8>; | |
| vdda-pll-supply = <&vreg_l3e_1p2>; | |
| status = "okay"; | |
| }; |