blob: 266a1bb8bb6e4f1e86bc07ded0265cfa6002239a [file] [log] [blame]
Qualcomm QMP PHY controller
===========================
QMP phy controller supports physical layer functionality for a number of
controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
Required properties:
- compatible: compatible list, contains:
"qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
"qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
"qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
"qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
"qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845.
- reg: offset and length of register set for PHY's common serdes block.
- #clock-cells: must be 1
- Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
interface (for pipe based PHYs). These clock are then gate-controlled
by gcc.
- #address-cells: must be 1
- #size-cells: must be 1
- ranges: must be present
- clocks: a list of phandles and clock-specifier pairs,
one for each entry in clock-names.
- clock-names: "cfg_ahb" for phy config clock,
"aux" for phy aux clock,
"ref" for 19.2 MHz ref clk,
"com_aux" for phy common block aux clock,
For "qcom,msm8996-qmp-pcie-phy" must contain:
"aux", "cfg_ahb", "ref".
For "qcom,msm8996-qmp-usb3-phy" must contain:
"aux", "cfg_ahb", "ref".
For "qcom,qmp-v3-usb3-phy" must contain:
"aux", "cfg_ahb", "ref", "com_aux".
- resets: a list of phandles and reset controller specifier pairs,
one for each entry in reset-names.
- reset-names: "phy" for reset of phy block,
"common" for phy common block reset,
"cfg" for phy's ahb cfg block reset (Optional).
For "qcom,msm8996-qmp-pcie-phy" must contain:
"phy", "common", "cfg".
For "qcom,msm8996-qmp-usb3-phy" must contain
"phy", "common".
For "qcom,ipq8074-qmp-pcie-phy" must contain:
"phy", "common".
- vdda-phy-supply: Phandle to a regulator supply to PHY core block.
- vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
Optional properties:
- vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
pll block.
Required nodes:
- Each device node of QMP phy is required to have as many child nodes as
the number of lanes the PHY has.
Required properties for child node:
- reg: list of offset and length pairs of register sets for PHY blocks -
tx, rx and pcs.
- #phy-cells: must be 0
- clocks: a list of phandles and clock-specifier pairs,
one for each entry in clock-names.
- clock-names: Must contain following for pcie and usb qmp phys:
"pipe<lane-number>" for pipe clock specific to each lane.
- clock-output-names: Name of the PHY clock that will be the parent for
the above pipe clock.
For "qcom,ipq8074-qmp-pcie-phy":
- "pcie20_phy0_pipe_clk" Pipe Clock parent
(or)
"pcie20_phy1_pipe_clk"
- resets: a list of phandles and reset controller specifier pairs,
one for each entry in reset-names.
- reset-names: Must contain following for pcie qmp phys:
"lane<lane-number>" for reset specific to each lane.
Example:
phy@34000 {
compatible = "qcom,msm8996-qmp-pcie-phy";
reg = <0x34000 0x488>;
#clock-cells = <1>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
<&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
<&gcc GCC_PCIE_CLKREF_CLK>;
clock-names = "aux", "cfg_ahb", "ref";
vdda-phy-supply = <&pm8994_l28>;
vdda-pll-supply = <&pm8994_l12>;
resets = <&gcc GCC_PCIE_PHY_BCR>,
<&gcc GCC_PCIE_PHY_COM_BCR>,
<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
reset-names = "phy", "common", "cfg";
pciephy_0: lane@35000 {
reg = <0x35000 0x130>,
<0x35200 0x200>,
<0x35400 0x1dc>;
#phy-cells = <0>;
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "pcie_0_pipe_clk_src";
resets = <&gcc GCC_PCIE_0_PHY_BCR>;
reset-names = "lane0";
};
pciephy_1: lane@36000 {
...
...
};