| /* SPDX-License-Identifier: GPL-2.0-or-later */ | |
| /* | |
| * pmbus.h - Common defines and structures for PMBus devices | |
| * | |
| * Copyright (c) 2010, 2011 Ericsson AB. | |
| * Copyright (c) 2012 Guenter Roeck | |
| */ | |
| #ifndef PMBUS_H | |
| #define PMBUS_H | |
| #include <linux/bitops.h> | |
| #include <linux/regulator/driver.h> | |
| /* | |
| * Registers | |
| */ | |
| enum pmbus_regs { | |
| PMBUS_PAGE = 0x00, | |
| PMBUS_OPERATION = 0x01, | |
| PMBUS_ON_OFF_CONFIG = 0x02, | |
| PMBUS_CLEAR_FAULTS = 0x03, | |
| PMBUS_PHASE = 0x04, | |
| PMBUS_WRITE_PROTECT = 0x10, | |
| PMBUS_CAPABILITY = 0x19, | |
| PMBUS_QUERY = 0x1A, | |
| PMBUS_VOUT_MODE = 0x20, | |
| PMBUS_VOUT_COMMAND = 0x21, | |
| PMBUS_VOUT_TRIM = 0x22, | |
| PMBUS_VOUT_CAL_OFFSET = 0x23, | |
| PMBUS_VOUT_MAX = 0x24, | |
| PMBUS_VOUT_MARGIN_HIGH = 0x25, | |
| PMBUS_VOUT_MARGIN_LOW = 0x26, | |
| PMBUS_VOUT_TRANSITION_RATE = 0x27, | |
| PMBUS_VOUT_DROOP = 0x28, | |
| PMBUS_VOUT_SCALE_LOOP = 0x29, | |
| PMBUS_VOUT_SCALE_MONITOR = 0x2A, | |
| PMBUS_COEFFICIENTS = 0x30, | |
| PMBUS_POUT_MAX = 0x31, | |
| PMBUS_FAN_CONFIG_12 = 0x3A, | |
| PMBUS_FAN_COMMAND_1 = 0x3B, | |
| PMBUS_FAN_COMMAND_2 = 0x3C, | |
| PMBUS_FAN_CONFIG_34 = 0x3D, | |
| PMBUS_FAN_COMMAND_3 = 0x3E, | |
| PMBUS_FAN_COMMAND_4 = 0x3F, | |
| PMBUS_VOUT_OV_FAULT_LIMIT = 0x40, | |
| PMBUS_VOUT_OV_FAULT_RESPONSE = 0x41, | |
| PMBUS_VOUT_OV_WARN_LIMIT = 0x42, | |
| PMBUS_VOUT_UV_WARN_LIMIT = 0x43, | |
| PMBUS_VOUT_UV_FAULT_LIMIT = 0x44, | |
| PMBUS_VOUT_UV_FAULT_RESPONSE = 0x45, | |
| PMBUS_IOUT_OC_FAULT_LIMIT = 0x46, | |
| PMBUS_IOUT_OC_FAULT_RESPONSE = 0x47, | |
| PMBUS_IOUT_OC_LV_FAULT_LIMIT = 0x48, | |
| PMBUS_IOUT_OC_LV_FAULT_RESPONSE = 0x49, | |
| PMBUS_IOUT_OC_WARN_LIMIT = 0x4A, | |
| PMBUS_IOUT_UC_FAULT_LIMIT = 0x4B, | |
| PMBUS_IOUT_UC_FAULT_RESPONSE = 0x4C, | |
| PMBUS_OT_FAULT_LIMIT = 0x4F, | |
| PMBUS_OT_FAULT_RESPONSE = 0x50, | |
| PMBUS_OT_WARN_LIMIT = 0x51, | |
| PMBUS_UT_WARN_LIMIT = 0x52, | |
| PMBUS_UT_FAULT_LIMIT = 0x53, | |
| PMBUS_UT_FAULT_RESPONSE = 0x54, | |
| PMBUS_VIN_OV_FAULT_LIMIT = 0x55, | |
| PMBUS_VIN_OV_FAULT_RESPONSE = 0x56, | |
| PMBUS_VIN_OV_WARN_LIMIT = 0x57, | |
| PMBUS_VIN_UV_WARN_LIMIT = 0x58, | |
| PMBUS_VIN_UV_FAULT_LIMIT = 0x59, | |
| PMBUS_IIN_OC_FAULT_LIMIT = 0x5B, | |
| PMBUS_IIN_OC_WARN_LIMIT = 0x5D, | |
| PMBUS_POUT_OP_FAULT_LIMIT = 0x68, | |
| PMBUS_POUT_OP_WARN_LIMIT = 0x6A, | |
| PMBUS_PIN_OP_WARN_LIMIT = 0x6B, | |
| PMBUS_STATUS_BYTE = 0x78, | |
| PMBUS_STATUS_WORD = 0x79, | |
| PMBUS_STATUS_VOUT = 0x7A, | |
| PMBUS_STATUS_IOUT = 0x7B, | |
| PMBUS_STATUS_INPUT = 0x7C, | |
| PMBUS_STATUS_TEMPERATURE = 0x7D, | |
| PMBUS_STATUS_CML = 0x7E, | |
| PMBUS_STATUS_OTHER = 0x7F, | |
| PMBUS_STATUS_MFR_SPECIFIC = 0x80, | |
| PMBUS_STATUS_FAN_12 = 0x81, | |
| PMBUS_STATUS_FAN_34 = 0x82, | |
| PMBUS_READ_VIN = 0x88, | |
| PMBUS_READ_IIN = 0x89, | |
| PMBUS_READ_VCAP = 0x8A, | |
| PMBUS_READ_VOUT = 0x8B, | |
| PMBUS_READ_IOUT = 0x8C, | |
| PMBUS_READ_TEMPERATURE_1 = 0x8D, | |
| PMBUS_READ_TEMPERATURE_2 = 0x8E, | |
| PMBUS_READ_TEMPERATURE_3 = 0x8F, | |
| PMBUS_READ_FAN_SPEED_1 = 0x90, | |
| PMBUS_READ_FAN_SPEED_2 = 0x91, | |
| PMBUS_READ_FAN_SPEED_3 = 0x92, | |
| PMBUS_READ_FAN_SPEED_4 = 0x93, | |
| PMBUS_READ_DUTY_CYCLE = 0x94, | |
| PMBUS_READ_FREQUENCY = 0x95, | |
| PMBUS_READ_POUT = 0x96, | |
| PMBUS_READ_PIN = 0x97, | |
| PMBUS_REVISION = 0x98, | |
| PMBUS_MFR_ID = 0x99, | |
| PMBUS_MFR_MODEL = 0x9A, | |
| PMBUS_MFR_REVISION = 0x9B, | |
| PMBUS_MFR_LOCATION = 0x9C, | |
| PMBUS_MFR_DATE = 0x9D, | |
| PMBUS_MFR_SERIAL = 0x9E, | |
| PMBUS_MFR_VIN_MIN = 0xA0, | |
| PMBUS_MFR_VIN_MAX = 0xA1, | |
| PMBUS_MFR_IIN_MAX = 0xA2, | |
| PMBUS_MFR_PIN_MAX = 0xA3, | |
| PMBUS_MFR_VOUT_MIN = 0xA4, | |
| PMBUS_MFR_VOUT_MAX = 0xA5, | |
| PMBUS_MFR_IOUT_MAX = 0xA6, | |
| PMBUS_MFR_POUT_MAX = 0xA7, | |
| PMBUS_IC_DEVICE_ID = 0xAD, | |
| PMBUS_IC_DEVICE_REV = 0xAE, | |
| PMBUS_MFR_MAX_TEMP_1 = 0xC0, | |
| PMBUS_MFR_MAX_TEMP_2 = 0xC1, | |
| PMBUS_MFR_MAX_TEMP_3 = 0xC2, | |
| /* | |
| * Virtual registers. | |
| * Useful to support attributes which are not supported by standard PMBus | |
| * registers but exist as manufacturer specific registers on individual chips. | |
| * Must be mapped to real registers in device specific code. | |
| * | |
| * Semantics: | |
| * Virtual registers are all word size. | |
| * READ registers are read-only; writes are either ignored or return an error. | |
| * RESET registers are read/write. Reading reset registers returns zero | |
| * (used for detection), writing any value causes the associated history to be | |
| * reset. | |
| * Virtual registers have to be handled in device specific driver code. Chip | |
| * driver code returns non-negative register values if a virtual register is | |
| * supported, or a negative error code if not. The chip driver may return | |
| * -ENODATA or any other error code in this case, though an error code other | |
| * than -ENODATA is handled more efficiently and thus preferred. Either case, | |
| * the calling PMBus core code will abort if the chip driver returns an error | |
| * code when reading or writing virtual registers. | |
| */ | |
| PMBUS_VIRT_BASE = 0x100, | |
| PMBUS_VIRT_READ_TEMP_AVG, | |
| PMBUS_VIRT_READ_TEMP_MIN, | |
| PMBUS_VIRT_READ_TEMP_MAX, | |
| PMBUS_VIRT_RESET_TEMP_HISTORY, | |
| PMBUS_VIRT_READ_VIN_AVG, | |
| PMBUS_VIRT_READ_VIN_MIN, | |
| PMBUS_VIRT_READ_VIN_MAX, | |
| PMBUS_VIRT_RESET_VIN_HISTORY, | |
| PMBUS_VIRT_READ_IIN_AVG, | |
| PMBUS_VIRT_READ_IIN_MIN, | |
| PMBUS_VIRT_READ_IIN_MAX, | |
| PMBUS_VIRT_RESET_IIN_HISTORY, | |
| PMBUS_VIRT_READ_PIN_AVG, | |
| PMBUS_VIRT_READ_PIN_MIN, | |
| PMBUS_VIRT_READ_PIN_MAX, | |
| PMBUS_VIRT_RESET_PIN_HISTORY, | |
| PMBUS_VIRT_READ_POUT_AVG, | |
| PMBUS_VIRT_READ_POUT_MIN, | |
| PMBUS_VIRT_READ_POUT_MAX, | |
| PMBUS_VIRT_RESET_POUT_HISTORY, | |
| PMBUS_VIRT_READ_VOUT_AVG, | |
| PMBUS_VIRT_READ_VOUT_MIN, | |
| PMBUS_VIRT_READ_VOUT_MAX, | |
| PMBUS_VIRT_RESET_VOUT_HISTORY, | |
| PMBUS_VIRT_READ_IOUT_AVG, | |
| PMBUS_VIRT_READ_IOUT_MIN, | |
| PMBUS_VIRT_READ_IOUT_MAX, | |
| PMBUS_VIRT_RESET_IOUT_HISTORY, | |
| PMBUS_VIRT_READ_TEMP2_AVG, | |
| PMBUS_VIRT_READ_TEMP2_MIN, | |
| PMBUS_VIRT_READ_TEMP2_MAX, | |
| PMBUS_VIRT_RESET_TEMP2_HISTORY, | |
| PMBUS_VIRT_READ_VMON, | |
| PMBUS_VIRT_VMON_UV_WARN_LIMIT, | |
| PMBUS_VIRT_VMON_OV_WARN_LIMIT, | |
| PMBUS_VIRT_VMON_UV_FAULT_LIMIT, | |
| PMBUS_VIRT_VMON_OV_FAULT_LIMIT, | |
| PMBUS_VIRT_STATUS_VMON, | |
| /* | |
| * RPM and PWM Fan control | |
| * | |
| * Drivers wanting to expose PWM control must define the behaviour of | |
| * PMBUS_VIRT_PWM_[1-4] and PMBUS_VIRT_PWM_ENABLE_[1-4] in the | |
| * {read,write}_word_data callback. | |
| * | |
| * pmbus core provides a default implementation for | |
| * PMBUS_VIRT_FAN_TARGET_[1-4]. | |
| * | |
| * TARGET, PWM and PWM_ENABLE members must be defined sequentially; | |
| * pmbus core uses the difference between the provided register and | |
| * it's _1 counterpart to calculate the FAN/PWM ID. | |
| */ | |
| PMBUS_VIRT_FAN_TARGET_1, | |
| PMBUS_VIRT_FAN_TARGET_2, | |
| PMBUS_VIRT_FAN_TARGET_3, | |
| PMBUS_VIRT_FAN_TARGET_4, | |
| PMBUS_VIRT_PWM_1, | |
| PMBUS_VIRT_PWM_2, | |
| PMBUS_VIRT_PWM_3, | |
| PMBUS_VIRT_PWM_4, | |
| PMBUS_VIRT_PWM_ENABLE_1, | |
| PMBUS_VIRT_PWM_ENABLE_2, | |
| PMBUS_VIRT_PWM_ENABLE_3, | |
| PMBUS_VIRT_PWM_ENABLE_4, | |
| /* Samples for average | |
| * | |
| * Drivers wanting to expose functionality for changing the number of | |
| * samples used for average values should implement support in | |
| * {read,write}_word_data callback for either PMBUS_VIRT_SAMPLES if it | |
| * applies to all types of measurements, or any number of specific | |
| * PMBUS_VIRT_*_SAMPLES registers to allow for individual control. | |
| */ | |
| PMBUS_VIRT_SAMPLES, | |
| PMBUS_VIRT_IN_SAMPLES, | |
| PMBUS_VIRT_CURR_SAMPLES, | |
| PMBUS_VIRT_POWER_SAMPLES, | |
| PMBUS_VIRT_TEMP_SAMPLES, | |
| }; | |
| /* | |
| * OPERATION | |
| */ | |
| #define PB_OPERATION_CONTROL_ON BIT(7) | |
| /* | |
| * WRITE_PROTECT | |
| */ | |
| #define PB_WP_ALL BIT(7) /* all but WRITE_PROTECT */ | |
| #define PB_WP_OP BIT(6) /* all but WP, OPERATION, PAGE */ | |
| #define PB_WP_VOUT BIT(5) /* all but WP, OPERATION, PAGE, VOUT, ON_OFF */ | |
| #define PB_WP_ANY (PB_WP_ALL | PB_WP_OP | PB_WP_VOUT) | |
| /* | |
| * CAPABILITY | |
| */ | |
| #define PB_CAPABILITY_SMBALERT BIT(4) | |
| #define PB_CAPABILITY_ERROR_CHECK BIT(7) | |
| /* | |
| * VOUT_MODE | |
| */ | |
| #define PB_VOUT_MODE_MODE_MASK 0xe0 | |
| #define PB_VOUT_MODE_PARAM_MASK 0x1f | |
| #define PB_VOUT_MODE_LINEAR 0x00 | |
| #define PB_VOUT_MODE_VID 0x20 | |
| #define PB_VOUT_MODE_DIRECT 0x40 | |
| /* | |
| * Fan configuration | |
| */ | |
| #define PB_FAN_2_PULSE_MASK (BIT(0) | BIT(1)) | |
| #define PB_FAN_2_RPM BIT(2) | |
| #define PB_FAN_2_INSTALLED BIT(3) | |
| #define PB_FAN_1_PULSE_MASK (BIT(4) | BIT(5)) | |
| #define PB_FAN_1_RPM BIT(6) | |
| #define PB_FAN_1_INSTALLED BIT(7) | |
| enum pmbus_fan_mode { percent = 0, rpm }; | |
| /* | |
| * STATUS_BYTE, STATUS_WORD (lower) | |
| */ | |
| #define PB_STATUS_NONE_ABOVE BIT(0) | |
| #define PB_STATUS_CML BIT(1) | |
| #define PB_STATUS_TEMPERATURE BIT(2) | |
| #define PB_STATUS_VIN_UV BIT(3) | |
| #define PB_STATUS_IOUT_OC BIT(4) | |
| #define PB_STATUS_VOUT_OV BIT(5) | |
| #define PB_STATUS_OFF BIT(6) | |
| #define PB_STATUS_BUSY BIT(7) | |
| /* | |
| * STATUS_WORD (upper) | |
| */ | |
| #define PB_STATUS_UNKNOWN BIT(8) | |
| #define PB_STATUS_OTHER BIT(9) | |
| #define PB_STATUS_FANS BIT(10) | |
| #define PB_STATUS_POWER_GOOD_N BIT(11) | |
| #define PB_STATUS_WORD_MFR BIT(12) | |
| #define PB_STATUS_INPUT BIT(13) | |
| #define PB_STATUS_IOUT_POUT BIT(14) | |
| #define PB_STATUS_VOUT BIT(15) | |
| /* | |
| * STATUS_IOUT | |
| */ | |
| #define PB_POUT_OP_WARNING BIT(0) | |
| #define PB_POUT_OP_FAULT BIT(1) | |
| #define PB_POWER_LIMITING BIT(2) | |
| #define PB_CURRENT_SHARE_FAULT BIT(3) | |
| #define PB_IOUT_UC_FAULT BIT(4) | |
| #define PB_IOUT_OC_WARNING BIT(5) | |
| #define PB_IOUT_OC_LV_FAULT BIT(6) | |
| #define PB_IOUT_OC_FAULT BIT(7) | |
| /* | |
| * STATUS_VOUT, STATUS_INPUT | |
| */ | |
| #define PB_VOLTAGE_VIN_OFF BIT(3) | |
| #define PB_VOLTAGE_UV_FAULT BIT(4) | |
| #define PB_VOLTAGE_UV_WARNING BIT(5) | |
| #define PB_VOLTAGE_OV_WARNING BIT(6) | |
| #define PB_VOLTAGE_OV_FAULT BIT(7) | |
| /* | |
| * STATUS_INPUT | |
| */ | |
| #define PB_PIN_OP_WARNING BIT(0) | |
| #define PB_IIN_OC_WARNING BIT(1) | |
| #define PB_IIN_OC_FAULT BIT(2) | |
| /* | |
| * STATUS_TEMPERATURE | |
| */ | |
| #define PB_TEMP_UT_FAULT BIT(4) | |
| #define PB_TEMP_UT_WARNING BIT(5) | |
| #define PB_TEMP_OT_WARNING BIT(6) | |
| #define PB_TEMP_OT_FAULT BIT(7) | |
| /* | |
| * STATUS_FAN | |
| */ | |
| #define PB_FAN_AIRFLOW_WARNING BIT(0) | |
| #define PB_FAN_AIRFLOW_FAULT BIT(1) | |
| #define PB_FAN_FAN2_SPEED_OVERRIDE BIT(2) | |
| #define PB_FAN_FAN1_SPEED_OVERRIDE BIT(3) | |
| #define PB_FAN_FAN2_WARNING BIT(4) | |
| #define PB_FAN_FAN1_WARNING BIT(5) | |
| #define PB_FAN_FAN2_FAULT BIT(6) | |
| #define PB_FAN_FAN1_FAULT BIT(7) | |
| /* | |
| * CML_FAULT_STATUS | |
| */ | |
| #define PB_CML_FAULT_OTHER_MEM_LOGIC BIT(0) | |
| #define PB_CML_FAULT_OTHER_COMM BIT(1) | |
| #define PB_CML_FAULT_PROCESSOR BIT(3) | |
| #define PB_CML_FAULT_MEMORY BIT(4) | |
| #define PB_CML_FAULT_PACKET_ERROR BIT(5) | |
| #define PB_CML_FAULT_INVALID_DATA BIT(6) | |
| #define PB_CML_FAULT_INVALID_COMMAND BIT(7) | |
| enum pmbus_sensor_classes { | |
| PSC_VOLTAGE_IN = 0, | |
| PSC_VOLTAGE_OUT, | |
| PSC_CURRENT_IN, | |
| PSC_CURRENT_OUT, | |
| PSC_POWER, | |
| PSC_TEMPERATURE, | |
| PSC_FAN, | |
| PSC_PWM, | |
| PSC_NUM_CLASSES /* Number of power sensor classes */ | |
| }; | |
| #define PMBUS_PAGES 32 /* Per PMBus specification */ | |
| #define PMBUS_PHASES 10 /* Maximum number of phases per page */ | |
| /* Functionality bit mask */ | |
| #define PMBUS_HAVE_VIN BIT(0) | |
| #define PMBUS_HAVE_VCAP BIT(1) | |
| #define PMBUS_HAVE_VOUT BIT(2) | |
| #define PMBUS_HAVE_IIN BIT(3) | |
| #define PMBUS_HAVE_IOUT BIT(4) | |
| #define PMBUS_HAVE_PIN BIT(5) | |
| #define PMBUS_HAVE_POUT BIT(6) | |
| #define PMBUS_HAVE_FAN12 BIT(7) | |
| #define PMBUS_HAVE_FAN34 BIT(8) | |
| #define PMBUS_HAVE_TEMP BIT(9) | |
| #define PMBUS_HAVE_TEMP2 BIT(10) | |
| #define PMBUS_HAVE_TEMP3 BIT(11) | |
| #define PMBUS_HAVE_STATUS_VOUT BIT(12) | |
| #define PMBUS_HAVE_STATUS_IOUT BIT(13) | |
| #define PMBUS_HAVE_STATUS_INPUT BIT(14) | |
| #define PMBUS_HAVE_STATUS_TEMP BIT(15) | |
| #define PMBUS_HAVE_STATUS_FAN12 BIT(16) | |
| #define PMBUS_HAVE_STATUS_FAN34 BIT(17) | |
| #define PMBUS_HAVE_VMON BIT(18) | |
| #define PMBUS_HAVE_STATUS_VMON BIT(19) | |
| #define PMBUS_HAVE_PWM12 BIT(20) | |
| #define PMBUS_HAVE_PWM34 BIT(21) | |
| #define PMBUS_HAVE_SAMPLES BIT(22) | |
| #define PMBUS_PHASE_VIRTUAL BIT(30) /* Phases on this page are virtual */ | |
| #define PMBUS_PAGE_VIRTUAL BIT(31) /* Page is virtual */ | |
| enum pmbus_data_format { linear = 0, ieee754, direct, vid }; | |
| enum vrm_version { vr11 = 0, vr12, vr13, imvp9, amd625mv }; | |
| struct pmbus_driver_info { | |
| int pages; /* Total number of pages */ | |
| u8 phases[PMBUS_PAGES]; /* Number of phases per page */ | |
| enum pmbus_data_format format[PSC_NUM_CLASSES]; | |
| enum vrm_version vrm_version[PMBUS_PAGES]; /* vrm version per page */ | |
| /* | |
| * Support one set of coefficients for each sensor type | |
| * Used for chips providing data in direct mode. | |
| */ | |
| int m[PSC_NUM_CLASSES]; /* mantissa for direct data format */ | |
| int b[PSC_NUM_CLASSES]; /* offset */ | |
| int R[PSC_NUM_CLASSES]; /* exponent */ | |
| u32 func[PMBUS_PAGES]; /* Functionality, per page */ | |
| u32 pfunc[PMBUS_PHASES];/* Functionality, per phase */ | |
| /* | |
| * The following functions map manufacturing specific register values | |
| * to PMBus standard register values. Specify only if mapping is | |
| * necessary. | |
| * Functions return the register value (read) or zero (write) if | |
| * successful. A return value of -ENODATA indicates that there is no | |
| * manufacturer specific register, but that a standard PMBus register | |
| * may exist. Any other negative return value indicates that the | |
| * register does not exist, and that no attempt should be made to read | |
| * the standard register. | |
| */ | |
| int (*read_byte_data)(struct i2c_client *client, int page, int reg); | |
| int (*read_word_data)(struct i2c_client *client, int page, int phase, | |
| int reg); | |
| int (*write_byte_data)(struct i2c_client *client, int page, int reg, | |
| u8 byte); | |
| int (*write_word_data)(struct i2c_client *client, int page, int reg, | |
| u16 word); | |
| int (*write_byte)(struct i2c_client *client, int page, u8 value); | |
| /* | |
| * The identify function determines supported PMBus functionality. | |
| * This function is only necessary if a chip driver supports multiple | |
| * chips, and the chip functionality is not pre-determined. | |
| */ | |
| int (*identify)(struct i2c_client *client, | |
| struct pmbus_driver_info *info); | |
| /* Regulator functionality, if supported by this chip driver. */ | |
| int num_regulators; | |
| const struct regulator_desc *reg_desc; | |
| /* custom attributes */ | |
| const struct attribute_group **groups; | |
| }; | |
| /* Regulator ops */ | |
| extern const struct regulator_ops pmbus_regulator_ops; | |
| /* Macros for filling in array of struct regulator_desc */ | |
| #define PMBUS_REGULATOR_STEP(_name, _id, _voltages, _step) \ | |
| [_id] = { \ | |
| .name = (_name # _id), \ | |
| .supply_name = "vin", \ | |
| .id = (_id), \ | |
| .of_match = of_match_ptr(_name # _id), \ | |
| .regulators_node = of_match_ptr("regulators"), \ | |
| .ops = &pmbus_regulator_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| .n_voltages = _voltages, \ | |
| .uV_step = _step, \ | |
| } | |
| #define PMBUS_REGULATOR(_name, _id) PMBUS_REGULATOR_STEP(_name, _id, 0, 0) | |
| /* Function declarations */ | |
| void pmbus_clear_cache(struct i2c_client *client); | |
| void pmbus_set_update(struct i2c_client *client, u8 reg, bool update); | |
| int pmbus_set_page(struct i2c_client *client, int page, int phase); | |
| int pmbus_read_word_data(struct i2c_client *client, int page, int phase, | |
| u8 reg); | |
| int pmbus_write_word_data(struct i2c_client *client, int page, u8 reg, | |
| u16 word); | |
| int pmbus_read_byte_data(struct i2c_client *client, int page, u8 reg); | |
| int pmbus_write_byte(struct i2c_client *client, int page, u8 value); | |
| int pmbus_write_byte_data(struct i2c_client *client, int page, u8 reg, | |
| u8 value); | |
| int pmbus_update_byte_data(struct i2c_client *client, int page, u8 reg, | |
| u8 mask, u8 value); | |
| void pmbus_clear_faults(struct i2c_client *client); | |
| bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg); | |
| bool pmbus_check_word_register(struct i2c_client *client, int page, int reg); | |
| int pmbus_do_probe(struct i2c_client *client, struct pmbus_driver_info *info); | |
| const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client | |
| *client); | |
| int pmbus_get_fan_rate_device(struct i2c_client *client, int page, int id, | |
| enum pmbus_fan_mode mode); | |
| int pmbus_get_fan_rate_cached(struct i2c_client *client, int page, int id, | |
| enum pmbus_fan_mode mode); | |
| int pmbus_update_fan(struct i2c_client *client, int page, int id, | |
| u8 config, u8 mask, u16 command); | |
| struct dentry *pmbus_get_debugfs_dir(struct i2c_client *client); | |
| #endif /* PMBUS_H */ |