| // SPDX-License-Identifier: GPL-2.0-or-later | |
| /* | |
| * Hardware monitoring driver for LTC3815 | |
| * | |
| * Copyright (c) 2015 Linear Technology | |
| * Copyright (c) 2015 Guenter Roeck | |
| */ | |
| #include <linux/err.h> | |
| #include <linux/i2c.h> | |
| #include <linux/init.h> | |
| #include <linux/jiffies.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include "pmbus.h" | |
| #define LTC3815_MFR_IOUT_PEAK 0xd7 | |
| #define LTC3815_MFR_VOUT_PEAK 0xdd | |
| #define LTC3815_MFR_VIN_PEAK 0xde | |
| #define LTC3815_MFR_TEMP_PEAK 0xdf | |
| #define LTC3815_MFR_IIN_PEAK 0xe1 | |
| #define LTC3815_MFR_SPECIAL_ID 0xe7 | |
| #define LTC3815_ID 0x8000 | |
| #define LTC3815_ID_MASK 0xff00 | |
| static int ltc3815_read_byte_data(struct i2c_client *client, int page, int reg) | |
| { | |
| int ret; | |
| switch (reg) { | |
| case PMBUS_VOUT_MODE: | |
| /* | |
| * The chip returns 0x3e, suggesting VID mode with manufacturer | |
| * specific VID codes. Since the output voltage is reported | |
| * with a LSB of 0.5mV, override and report direct mode with | |
| * appropriate coefficients. | |
| */ | |
| ret = 0x40; | |
| break; | |
| default: | |
| ret = -ENODATA; | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int ltc3815_write_byte(struct i2c_client *client, int page, u8 reg) | |
| { | |
| int ret; | |
| switch (reg) { | |
| case PMBUS_CLEAR_FAULTS: | |
| /* | |
| * LTC3815 does not support the CLEAR_FAULTS command. | |
| * Emulate it by clearing the status register. | |
| */ | |
| ret = pmbus_read_word_data(client, 0, 0xff, PMBUS_STATUS_WORD); | |
| if (ret > 0) { | |
| pmbus_write_word_data(client, 0, PMBUS_STATUS_WORD, | |
| ret); | |
| ret = 0; | |
| } | |
| break; | |
| default: | |
| ret = -ENODATA; | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int ltc3815_read_word_data(struct i2c_client *client, int page, | |
| int phase, int reg) | |
| { | |
| int ret; | |
| switch (reg) { | |
| case PMBUS_VIRT_READ_VIN_MAX: | |
| ret = pmbus_read_word_data(client, page, phase, | |
| LTC3815_MFR_VIN_PEAK); | |
| break; | |
| case PMBUS_VIRT_READ_VOUT_MAX: | |
| ret = pmbus_read_word_data(client, page, phase, | |
| LTC3815_MFR_VOUT_PEAK); | |
| break; | |
| case PMBUS_VIRT_READ_TEMP_MAX: | |
| ret = pmbus_read_word_data(client, page, phase, | |
| LTC3815_MFR_TEMP_PEAK); | |
| break; | |
| case PMBUS_VIRT_READ_IOUT_MAX: | |
| ret = pmbus_read_word_data(client, page, phase, | |
| LTC3815_MFR_IOUT_PEAK); | |
| break; | |
| case PMBUS_VIRT_READ_IIN_MAX: | |
| ret = pmbus_read_word_data(client, page, phase, | |
| LTC3815_MFR_IIN_PEAK); | |
| break; | |
| case PMBUS_VIRT_RESET_VOUT_HISTORY: | |
| case PMBUS_VIRT_RESET_VIN_HISTORY: | |
| case PMBUS_VIRT_RESET_TEMP_HISTORY: | |
| case PMBUS_VIRT_RESET_IOUT_HISTORY: | |
| case PMBUS_VIRT_RESET_IIN_HISTORY: | |
| ret = 0; | |
| break; | |
| default: | |
| ret = -ENODATA; | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int ltc3815_write_word_data(struct i2c_client *client, int page, | |
| int reg, u16 word) | |
| { | |
| int ret; | |
| switch (reg) { | |
| case PMBUS_VIRT_RESET_IIN_HISTORY: | |
| ret = pmbus_write_word_data(client, page, | |
| LTC3815_MFR_IIN_PEAK, 0); | |
| break; | |
| case PMBUS_VIRT_RESET_IOUT_HISTORY: | |
| ret = pmbus_write_word_data(client, page, | |
| LTC3815_MFR_IOUT_PEAK, 0); | |
| break; | |
| case PMBUS_VIRT_RESET_VOUT_HISTORY: | |
| ret = pmbus_write_word_data(client, page, | |
| LTC3815_MFR_VOUT_PEAK, 0); | |
| break; | |
| case PMBUS_VIRT_RESET_VIN_HISTORY: | |
| ret = pmbus_write_word_data(client, page, | |
| LTC3815_MFR_VIN_PEAK, 0); | |
| break; | |
| case PMBUS_VIRT_RESET_TEMP_HISTORY: | |
| ret = pmbus_write_word_data(client, page, | |
| LTC3815_MFR_TEMP_PEAK, 0); | |
| break; | |
| default: | |
| ret = -ENODATA; | |
| break; | |
| } | |
| return ret; | |
| } | |
| static const struct i2c_device_id ltc3815_id[] = { | |
| {"ltc3815", 0}, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, ltc3815_id); | |
| static struct pmbus_driver_info ltc3815_info = { | |
| .pages = 1, | |
| .format[PSC_VOLTAGE_IN] = direct, | |
| .format[PSC_VOLTAGE_OUT] = direct, | |
| .format[PSC_CURRENT_IN] = direct, | |
| .format[PSC_CURRENT_OUT] = direct, | |
| .format[PSC_TEMPERATURE] = direct, | |
| .m[PSC_VOLTAGE_IN] = 250, | |
| .b[PSC_VOLTAGE_IN] = 0, | |
| .R[PSC_VOLTAGE_IN] = 0, | |
| .m[PSC_VOLTAGE_OUT] = 2, | |
| .b[PSC_VOLTAGE_OUT] = 0, | |
| .R[PSC_VOLTAGE_OUT] = 3, | |
| .m[PSC_CURRENT_IN] = 1, | |
| .b[PSC_CURRENT_IN] = 0, | |
| .R[PSC_CURRENT_IN] = 2, | |
| .m[PSC_CURRENT_OUT] = 1, | |
| .b[PSC_CURRENT_OUT] = 0, | |
| .R[PSC_CURRENT_OUT] = 2, | |
| .m[PSC_TEMPERATURE] = 1, | |
| .b[PSC_TEMPERATURE] = 0, | |
| .R[PSC_TEMPERATURE] = 0, | |
| .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_VOUT | | |
| PMBUS_HAVE_IOUT | PMBUS_HAVE_TEMP, | |
| .read_byte_data = ltc3815_read_byte_data, | |
| .read_word_data = ltc3815_read_word_data, | |
| .write_byte = ltc3815_write_byte, | |
| .write_word_data = ltc3815_write_word_data, | |
| }; | |
| static int ltc3815_probe(struct i2c_client *client) | |
| { | |
| int chip_id; | |
| if (!i2c_check_functionality(client->adapter, | |
| I2C_FUNC_SMBUS_READ_WORD_DATA)) | |
| return -ENODEV; | |
| chip_id = i2c_smbus_read_word_data(client, LTC3815_MFR_SPECIAL_ID); | |
| if (chip_id < 0) | |
| return chip_id; | |
| if ((chip_id & LTC3815_ID_MASK) != LTC3815_ID) | |
| return -ENODEV; | |
| return pmbus_do_probe(client, <c3815_info); | |
| } | |
| static struct i2c_driver ltc3815_driver = { | |
| .driver = { | |
| .name = "ltc3815", | |
| }, | |
| .probe_new = ltc3815_probe, | |
| .id_table = ltc3815_id, | |
| }; | |
| module_i2c_driver(ltc3815_driver); | |
| MODULE_AUTHOR("Guenter Roeck"); | |
| MODULE_DESCRIPTION("PMBus driver for LTC3815"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_IMPORT_NS(PMBUS); |