| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Initialize MMU support. | |
| * | |
| * Copyright (C) 1998-2003 Hewlett-Packard Co | |
| * David Mosberger-Tang <davidm@hpl.hp.com> | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/dma-map-ops.h> | |
| #include <linux/dmar.h> | |
| #include <linux/efi.h> | |
| #include <linux/elf.h> | |
| #include <linux/memblock.h> | |
| #include <linux/mm.h> | |
| #include <linux/sched/signal.h> | |
| #include <linux/mmzone.h> | |
| #include <linux/module.h> | |
| #include <linux/personality.h> | |
| #include <linux/reboot.h> | |
| #include <linux/slab.h> | |
| #include <linux/swap.h> | |
| #include <linux/proc_fs.h> | |
| #include <linux/bitops.h> | |
| #include <linux/kexec.h> | |
| #include <linux/swiotlb.h> | |
| #include <asm/dma.h> | |
| #include <asm/efi.h> | |
| #include <asm/io.h> | |
| #include <asm/numa.h> | |
| #include <asm/patch.h> | |
| #include <asm/pgalloc.h> | |
| #include <asm/sal.h> | |
| #include <asm/sections.h> | |
| #include <asm/tlb.h> | |
| #include <linux/uaccess.h> | |
| #include <asm/unistd.h> | |
| #include <asm/mca.h> | |
| extern void ia64_tlb_init (void); | |
| unsigned long MAX_DMA_ADDRESS = PAGE_OFFSET + 0x100000000UL; | |
| struct page *zero_page_memmap_ptr; /* map entry for zero page */ | |
| EXPORT_SYMBOL(zero_page_memmap_ptr); | |
| void | |
| __ia64_sync_icache_dcache (pte_t pte) | |
| { | |
| unsigned long addr; | |
| struct page *page; | |
| page = pte_page(pte); | |
| addr = (unsigned long) page_address(page); | |
| if (test_bit(PG_arch_1, &page->flags)) | |
| return; /* i-cache is already coherent with d-cache */ | |
| flush_icache_range(addr, addr + page_size(page)); | |
| set_bit(PG_arch_1, &page->flags); /* mark page as clean */ | |
| } | |
| /* | |
| * Since DMA is i-cache coherent, any (complete) pages that were written via | |
| * DMA can be marked as "clean" so that lazy_mmu_prot_update() doesn't have to | |
| * flush them when they get mapped into an executable vm-area. | |
| */ | |
| void arch_dma_mark_clean(phys_addr_t paddr, size_t size) | |
| { | |
| unsigned long pfn = PHYS_PFN(paddr); | |
| do { | |
| set_bit(PG_arch_1, &pfn_to_page(pfn)->flags); | |
| } while (++pfn <= PHYS_PFN(paddr + size - 1)); | |
| } | |
| inline void | |
| ia64_set_rbs_bot (void) | |
| { | |
| unsigned long stack_size = rlimit_max(RLIMIT_STACK) & -16; | |
| if (stack_size > MAX_USER_STACK_SIZE) | |
| stack_size = MAX_USER_STACK_SIZE; | |
| current->thread.rbs_bot = PAGE_ALIGN(current->mm->start_stack - stack_size); | |
| } | |
| /* | |
| * This performs some platform-dependent address space initialization. | |
| * On IA-64, we want to setup the VM area for the register backing | |
| * store (which grows upwards) and install the gateway page which is | |
| * used for signal trampolines, etc. | |
| */ | |
| void | |
| ia64_init_addr_space (void) | |
| { | |
| struct vm_area_struct *vma; | |
| ia64_set_rbs_bot(); | |
| /* | |
| * If we're out of memory and kmem_cache_alloc() returns NULL, we simply ignore | |
| * the problem. When the process attempts to write to the register backing store | |
| * for the first time, it will get a SEGFAULT in this case. | |
| */ | |
| vma = vm_area_alloc(current->mm); | |
| if (vma) { | |
| vma_set_anonymous(vma); | |
| vma->vm_start = current->thread.rbs_bot & PAGE_MASK; | |
| vma->vm_end = vma->vm_start + PAGE_SIZE; | |
| vma->vm_flags = VM_DATA_DEFAULT_FLAGS|VM_GROWSUP|VM_ACCOUNT; | |
| vma->vm_page_prot = vm_get_page_prot(vma->vm_flags); | |
| mmap_write_lock(current->mm); | |
| if (insert_vm_struct(current->mm, vma)) { | |
| mmap_write_unlock(current->mm); | |
| vm_area_free(vma); | |
| return; | |
| } | |
| mmap_write_unlock(current->mm); | |
| } | |
| /* map NaT-page at address zero to speed up speculative dereferencing of NULL: */ | |
| if (!(current->personality & MMAP_PAGE_ZERO)) { | |
| vma = vm_area_alloc(current->mm); | |
| if (vma) { | |
| vma_set_anonymous(vma); | |
| vma->vm_end = PAGE_SIZE; | |
| vma->vm_page_prot = __pgprot(pgprot_val(PAGE_READONLY) | _PAGE_MA_NAT); | |
| vma->vm_flags = VM_READ | VM_MAYREAD | VM_IO | | |
| VM_DONTEXPAND | VM_DONTDUMP; | |
| mmap_write_lock(current->mm); | |
| if (insert_vm_struct(current->mm, vma)) { | |
| mmap_write_unlock(current->mm); | |
| vm_area_free(vma); | |
| return; | |
| } | |
| mmap_write_unlock(current->mm); | |
| } | |
| } | |
| } | |
| void | |
| free_initmem (void) | |
| { | |
| free_reserved_area(ia64_imva(__init_begin), ia64_imva(__init_end), | |
| -1, "unused kernel"); | |
| } | |
| void __init | |
| free_initrd_mem (unsigned long start, unsigned long end) | |
| { | |
| /* | |
| * EFI uses 4KB pages while the kernel can use 4KB or bigger. | |
| * Thus EFI and the kernel may have different page sizes. It is | |
| * therefore possible to have the initrd share the same page as | |
| * the end of the kernel (given current setup). | |
| * | |
| * To avoid freeing/using the wrong page (kernel sized) we: | |
| * - align up the beginning of initrd | |
| * - align down the end of initrd | |
| * | |
| * | | | |
| * |=============| a000 | |
| * | | | |
| * | | | |
| * | | 9000 | |
| * |/////////////| | |
| * |/////////////| | |
| * |=============| 8000 | |
| * |///INITRD////| | |
| * |/////////////| | |
| * |/////////////| 7000 | |
| * | | | |
| * |KKKKKKKKKKKKK| | |
| * |=============| 6000 | |
| * |KKKKKKKKKKKKK| | |
| * |KKKKKKKKKKKKK| | |
| * K=kernel using 8KB pages | |
| * | |
| * In this example, we must free page 8000 ONLY. So we must align up | |
| * initrd_start and keep initrd_end as is. | |
| */ | |
| start = PAGE_ALIGN(start); | |
| end = end & PAGE_MASK; | |
| if (start < end) | |
| printk(KERN_INFO "Freeing initrd memory: %ldkB freed\n", (end - start) >> 10); | |
| for (; start < end; start += PAGE_SIZE) { | |
| if (!virt_addr_valid(start)) | |
| continue; | |
| free_reserved_page(virt_to_page(start)); | |
| } | |
| } | |
| /* | |
| * This installs a clean page in the kernel's page table. | |
| */ | |
| static struct page * __init | |
| put_kernel_page (struct page *page, unsigned long address, pgprot_t pgprot) | |
| { | |
| pgd_t *pgd; | |
| p4d_t *p4d; | |
| pud_t *pud; | |
| pmd_t *pmd; | |
| pte_t *pte; | |
| pgd = pgd_offset_k(address); /* note: this is NOT pgd_offset()! */ | |
| { | |
| p4d = p4d_alloc(&init_mm, pgd, address); | |
| if (!p4d) | |
| goto out; | |
| pud = pud_alloc(&init_mm, p4d, address); | |
| if (!pud) | |
| goto out; | |
| pmd = pmd_alloc(&init_mm, pud, address); | |
| if (!pmd) | |
| goto out; | |
| pte = pte_alloc_kernel(pmd, address); | |
| if (!pte) | |
| goto out; | |
| if (!pte_none(*pte)) | |
| goto out; | |
| set_pte(pte, mk_pte(page, pgprot)); | |
| } | |
| out: | |
| /* no need for flush_tlb */ | |
| return page; | |
| } | |
| static void __init | |
| setup_gate (void) | |
| { | |
| struct page *page; | |
| /* | |
| * Map the gate page twice: once read-only to export the ELF | |
| * headers etc. and once execute-only page to enable | |
| * privilege-promotion via "epc": | |
| */ | |
| page = virt_to_page(ia64_imva(__start_gate_section)); | |
| put_kernel_page(page, GATE_ADDR, PAGE_READONLY); | |
| #ifdef HAVE_BUGGY_SEGREL | |
| page = virt_to_page(ia64_imva(__start_gate_section + PAGE_SIZE)); | |
| put_kernel_page(page, GATE_ADDR + PAGE_SIZE, PAGE_GATE); | |
| #else | |
| put_kernel_page(page, GATE_ADDR + PERCPU_PAGE_SIZE, PAGE_GATE); | |
| /* Fill in the holes (if any) with read-only zero pages: */ | |
| { | |
| unsigned long addr; | |
| for (addr = GATE_ADDR + PAGE_SIZE; | |
| addr < GATE_ADDR + PERCPU_PAGE_SIZE; | |
| addr += PAGE_SIZE) | |
| { | |
| put_kernel_page(ZERO_PAGE(0), addr, | |
| PAGE_READONLY); | |
| put_kernel_page(ZERO_PAGE(0), addr + PERCPU_PAGE_SIZE, | |
| PAGE_READONLY); | |
| } | |
| } | |
| #endif | |
| ia64_patch_gate(); | |
| } | |
| static struct vm_area_struct gate_vma; | |
| static int __init gate_vma_init(void) | |
| { | |
| vma_init(&gate_vma, NULL); | |
| gate_vma.vm_start = FIXADDR_USER_START; | |
| gate_vma.vm_end = FIXADDR_USER_END; | |
| gate_vma.vm_flags = VM_READ | VM_MAYREAD | VM_EXEC | VM_MAYEXEC; | |
| gate_vma.vm_page_prot = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | _PAGE_AR_RX); | |
| return 0; | |
| } | |
| __initcall(gate_vma_init); | |
| struct vm_area_struct *get_gate_vma(struct mm_struct *mm) | |
| { | |
| return &gate_vma; | |
| } | |
| int in_gate_area_no_mm(unsigned long addr) | |
| { | |
| if ((addr >= FIXADDR_USER_START) && (addr < FIXADDR_USER_END)) | |
| return 1; | |
| return 0; | |
| } | |
| int in_gate_area(struct mm_struct *mm, unsigned long addr) | |
| { | |
| return in_gate_area_no_mm(addr); | |
| } | |
| void ia64_mmu_init(void *my_cpu_data) | |
| { | |
| unsigned long pta, impl_va_bits; | |
| extern void tlb_init(void); | |
| #ifdef CONFIG_DISABLE_VHPT | |
| # define VHPT_ENABLE_BIT 0 | |
| #else | |
| # define VHPT_ENABLE_BIT 1 | |
| #endif | |
| /* | |
| * Check if the virtually mapped linear page table (VMLPT) overlaps with a mapped | |
| * address space. The IA-64 architecture guarantees that at least 50 bits of | |
| * virtual address space are implemented but if we pick a large enough page size | |
| * (e.g., 64KB), the mapped address space is big enough that it will overlap with | |
| * VMLPT. I assume that once we run on machines big enough to warrant 64KB pages, | |
| * IMPL_VA_MSB will be significantly bigger, so this is unlikely to become a | |
| * problem in practice. Alternatively, we could truncate the top of the mapped | |
| * address space to not permit mappings that would overlap with the VMLPT. | |
| * --davidm 00/12/06 | |
| */ | |
| # define pte_bits 3 | |
| # define mapped_space_bits (3*(PAGE_SHIFT - pte_bits) + PAGE_SHIFT) | |
| /* | |
| * The virtual page table has to cover the entire implemented address space within | |
| * a region even though not all of this space may be mappable. The reason for | |
| * this is that the Access bit and Dirty bit fault handlers perform | |
| * non-speculative accesses to the virtual page table, so the address range of the | |
| * virtual page table itself needs to be covered by virtual page table. | |
| */ | |
| # define vmlpt_bits (impl_va_bits - PAGE_SHIFT + pte_bits) | |
| # define POW2(n) (1ULL << (n)) | |
| impl_va_bits = ffz(~(local_cpu_data->unimpl_va_mask | (7UL << 61))); | |
| if (impl_va_bits < 51 || impl_va_bits > 61) | |
| panic("CPU has bogus IMPL_VA_MSB value of %lu!\n", impl_va_bits - 1); | |
| /* | |
| * mapped_space_bits - PAGE_SHIFT is the total number of ptes we need, | |
| * which must fit into "vmlpt_bits - pte_bits" slots. Second half of | |
| * the test makes sure that our mapped space doesn't overlap the | |
| * unimplemented hole in the middle of the region. | |
| */ | |
| if ((mapped_space_bits - PAGE_SHIFT > vmlpt_bits - pte_bits) || | |
| (mapped_space_bits > impl_va_bits - 1)) | |
| panic("Cannot build a big enough virtual-linear page table" | |
| " to cover mapped address space.\n" | |
| " Try using a smaller page size.\n"); | |
| /* place the VMLPT at the end of each page-table mapped region: */ | |
| pta = POW2(61) - POW2(vmlpt_bits); | |
| /* | |
| * Set the (virtually mapped linear) page table address. Bit | |
| * 8 selects between the short and long format, bits 2-7 the | |
| * size of the table, and bit 0 whether the VHPT walker is | |
| * enabled. | |
| */ | |
| ia64_set_pta(pta | (0 << 8) | (vmlpt_bits << 2) | VHPT_ENABLE_BIT); | |
| ia64_tlb_init(); | |
| #ifdef CONFIG_HUGETLB_PAGE | |
| ia64_set_rr(HPAGE_REGION_BASE, HPAGE_SHIFT << 2); | |
| ia64_srlz_d(); | |
| #endif | |
| } | |
| int __init register_active_ranges(u64 start, u64 len, int nid) | |
| { | |
| u64 end = start + len; | |
| #ifdef CONFIG_KEXEC | |
| if (start > crashk_res.start && start < crashk_res.end) | |
| start = crashk_res.end; | |
| if (end > crashk_res.start && end < crashk_res.end) | |
| end = crashk_res.start; | |
| #endif | |
| if (start < end) | |
| memblock_add_node(__pa(start), end - start, nid, MEMBLOCK_NONE); | |
| return 0; | |
| } | |
| int | |
| find_max_min_low_pfn (u64 start, u64 end, void *arg) | |
| { | |
| unsigned long pfn_start, pfn_end; | |
| #ifdef CONFIG_FLATMEM | |
| pfn_start = (PAGE_ALIGN(__pa(start))) >> PAGE_SHIFT; | |
| pfn_end = (PAGE_ALIGN(__pa(end - 1))) >> PAGE_SHIFT; | |
| #else | |
| pfn_start = GRANULEROUNDDOWN(__pa(start)) >> PAGE_SHIFT; | |
| pfn_end = GRANULEROUNDUP(__pa(end - 1)) >> PAGE_SHIFT; | |
| #endif | |
| min_low_pfn = min(min_low_pfn, pfn_start); | |
| max_low_pfn = max(max_low_pfn, pfn_end); | |
| return 0; | |
| } | |
| /* | |
| * Boot command-line option "nolwsys" can be used to disable the use of any light-weight | |
| * system call handler. When this option is in effect, all fsyscalls will end up bubbling | |
| * down into the kernel and calling the normal (heavy-weight) syscall handler. This is | |
| * useful for performance testing, but conceivably could also come in handy for debugging | |
| * purposes. | |
| */ | |
| static int nolwsys __initdata; | |
| static int __init | |
| nolwsys_setup (char *s) | |
| { | |
| nolwsys = 1; | |
| return 1; | |
| } | |
| __setup("nolwsys", nolwsys_setup); | |
| void __init | |
| mem_init (void) | |
| { | |
| int i; | |
| BUG_ON(PTRS_PER_PGD * sizeof(pgd_t) != PAGE_SIZE); | |
| BUG_ON(PTRS_PER_PMD * sizeof(pmd_t) != PAGE_SIZE); | |
| BUG_ON(PTRS_PER_PTE * sizeof(pte_t) != PAGE_SIZE); | |
| /* | |
| * This needs to be called _after_ the command line has been parsed but | |
| * _before_ any drivers that may need the PCI DMA interface are | |
| * initialized or bootmem has been freed. | |
| */ | |
| do { | |
| #ifdef CONFIG_INTEL_IOMMU | |
| detect_intel_iommu(); | |
| if (iommu_detected) | |
| break; | |
| #endif | |
| swiotlb_init(true, SWIOTLB_VERBOSE); | |
| } while (0); | |
| #ifdef CONFIG_FLATMEM | |
| BUG_ON(!mem_map); | |
| #endif | |
| set_max_mapnr(max_low_pfn); | |
| high_memory = __va(max_low_pfn * PAGE_SIZE); | |
| memblock_free_all(); | |
| /* | |
| * For fsyscall entrypoints with no light-weight handler, use the ordinary | |
| * (heavy-weight) handler, but mark it by setting bit 0, so the fsyscall entry | |
| * code can tell them apart. | |
| */ | |
| for (i = 0; i < NR_syscalls; ++i) { | |
| extern unsigned long fsyscall_table[NR_syscalls]; | |
| extern unsigned long sys_call_table[NR_syscalls]; | |
| if (!fsyscall_table[i] || nolwsys) | |
| fsyscall_table[i] = sys_call_table[i] | 1; | |
| } | |
| setup_gate(); | |
| } | |
| #ifdef CONFIG_MEMORY_HOTPLUG | |
| int arch_add_memory(int nid, u64 start, u64 size, | |
| struct mhp_params *params) | |
| { | |
| unsigned long start_pfn = start >> PAGE_SHIFT; | |
| unsigned long nr_pages = size >> PAGE_SHIFT; | |
| int ret; | |
| if (WARN_ON_ONCE(params->pgprot.pgprot != PAGE_KERNEL.pgprot)) | |
| return -EINVAL; | |
| ret = __add_pages(nid, start_pfn, nr_pages, params); | |
| if (ret) | |
| printk("%s: Problem encountered in __add_pages() as ret=%d\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| void arch_remove_memory(u64 start, u64 size, struct vmem_altmap *altmap) | |
| { | |
| unsigned long start_pfn = start >> PAGE_SHIFT; | |
| unsigned long nr_pages = size >> PAGE_SHIFT; | |
| __remove_pages(start_pfn, nr_pages, altmap); | |
| } | |
| #endif | |
| static const pgprot_t protection_map[16] = { | |
| [VM_NONE] = PAGE_NONE, | |
| [VM_READ] = PAGE_READONLY, | |
| [VM_WRITE] = PAGE_READONLY, | |
| [VM_WRITE | VM_READ] = PAGE_READONLY, | |
| [VM_EXEC] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_X_RX), | |
| [VM_EXEC | VM_READ] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_RX), | |
| [VM_EXEC | VM_WRITE] = PAGE_COPY_EXEC, | |
| [VM_EXEC | VM_WRITE | VM_READ] = PAGE_COPY_EXEC, | |
| [VM_SHARED] = PAGE_NONE, | |
| [VM_SHARED | VM_READ] = PAGE_READONLY, | |
| [VM_SHARED | VM_WRITE] = PAGE_SHARED, | |
| [VM_SHARED | VM_WRITE | VM_READ] = PAGE_SHARED, | |
| [VM_SHARED | VM_EXEC] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_X_RX), | |
| [VM_SHARED | VM_EXEC | VM_READ] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_RX), | |
| [VM_SHARED | VM_EXEC | VM_WRITE] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_RWX), | |
| [VM_SHARED | VM_EXEC | VM_WRITE | VM_READ] = __pgprot(__ACCESS_BITS | _PAGE_PL_3 | | |
| _PAGE_AR_RWX) | |
| }; | |
| DECLARE_VM_GET_PAGE_PROT |