| # SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/soc/qcom/qcom,gsbi.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: Qualcomm General Serial Bus Interface (GSBI) | |
| maintainers: | |
| - Andy Gross <agross@kernel.org> | |
| - Bjorn Andersson <bjorn.andersson@linaro.org> | |
| - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> | |
| description: | |
| The GSBI controller is modeled as a node with zero or more child nodes, each | |
| representing a serial sub-node device that is mux'd as part of the GSBI | |
| configuration settings. The mode setting will govern the input/output mode | |
| of the 4 GSBI IOs. | |
| A GSBI controller node can contain 0 or more child nodes representing serial | |
| devices. These serial devices can be a QCOM UART, I2C controller, spi | |
| controller, or some combination of aforementioned devices. | |
| properties: | |
| compatible: | |
| const: qcom,gsbi-v1.0.0 | |
| '#address-cells': | |
| const: 1 | |
| cell-index: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | |
| The GSBI index. | |
| clocks: | |
| maxItems: 1 | |
| clock-names: | |
| const: iface | |
| qcom,crci: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | |
| CRCI MUX value for QUP CRCI ports. Please reference | |
| include/dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. | |
| qcom,mode: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | |
| MUX value for configuration of the serial interface. Please reference | |
| include/dt-bindings/soc/qcom,gsbi.h for valid mux values. | |
| '#size-cells': | |
| const: 1 | |
| syscon-tcsr: | |
| $ref: /schemas/types.yaml#/definitions/phandle | |
| description: | |
| Phandle of TCSR syscon node.Required if child uses dma. | |
| ranges: true | |
| reg: | |
| maxItems: 1 | |
| patternProperties: | |
| "spi@[0-9a-f]+$": | |
| type: object | |
| $ref: /schemas/spi/qcom,spi-qup.yaml# | |
| "i2c@[0-9a-f]+$": | |
| type: object | |
| $ref: /schemas/i2c/qcom,i2c-qup.yaml# | |
| "serial@[0-9a-f]+$": | |
| type: object | |
| $ref: /schemas/serial/qcom,msm-uartdm.yaml# | |
| required: | |
| - compatible | |
| - cell-index | |
| - clocks | |
| - clock-names | |
| - qcom,mode | |
| - reg | |
| additionalProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/clock/qcom,gcc-msm8960.h> | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> | |
| #include <dt-bindings/soc/qcom,gsbi.h> | |
| gsbi@12440000 { | |
| compatible = "qcom,gsbi-v1.0.0"; | |
| reg = <0x12440000 0x100>; | |
| cell-index = <1>; | |
| clocks = <&gcc GSBI1_H_CLK>; | |
| clock-names = "iface"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges; | |
| syscon-tcsr = <&tcsr>; | |
| qcom,mode = <GSBI_PROT_I2C_UART>; | |
| serial@12450000 { | |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; | |
| reg = <0x12450000 0x100>, | |
| <0x12400000 0x03>; | |
| interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; | |
| clock-names = "core", "iface"; | |
| }; | |
| i2c@12460000 { | |
| compatible = "qcom,i2c-qup-v1.1.1"; | |
| reg = <0x12460000 0x1000>; | |
| pinctrl-0 = <&i2c1_pins>; | |
| pinctrl-1 = <&i2c1_pins_sleep>; | |
| pinctrl-names = "default", "sleep"; | |
| interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; | |
| clock-names = "core", "iface"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; /* UART chosen */ | |
| }; | |
| }; |