| # SPDX-License-Identifier: GPL-2.0-only | |
| # | |
| # 1-wire bus master configuration | |
| # | |
| menu "1-wire Bus Masters" | |
| config W1_MASTER_AMD_AXI | |
| tristate "AMD AXI 1-wire bus host" | |
| help | |
| Say Y here is you want to support the AMD AXI 1-wire IP core. | |
| This driver makes use of the programmable logic IP to perform | |
| correctly timed 1 wire transactions without relying on GPIO timing | |
| through the kernel. | |
| This driver can also be built as a module. If so, the module will be | |
| called amd_w1_axi. | |
| config W1_MASTER_MATROX | |
| tristate "Matrox G400 transport layer for 1-wire" | |
| depends on PCI | |
| help | |
| Say Y here if you want to communicate with your 1-wire devices | |
| using Matrox's G400 GPIO pins. | |
| This support is also available as a module. If so, the module | |
| will be called matrox_w1. | |
| config W1_MASTER_DS2490 | |
| tristate "DS2490 USB <-> W1 transport layer for 1-wire" | |
| depends on USB | |
| help | |
| Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges, | |
| for example DS9490*. | |
| This support is also available as a module. If so, the module | |
| will be called ds2490. | |
| config W1_MASTER_DS2482 | |
| tristate "Maxim DS2482 I2C to 1-Wire bridge" | |
| depends on I2C | |
| help | |
| If you say yes here you get support for the Maxim DS2482 | |
| I2C to 1-Wire bridge. | |
| This driver can also be built as a module. If so, the module | |
| will be called ds2482. | |
| config W1_MASTER_MXC | |
| tristate "Freescale MXC 1-wire busmaster" | |
| depends on ARCH_MXC || COMPILE_TEST | |
| help | |
| Say Y here to enable MXC 1-wire host | |
| config W1_MASTER_GPIO | |
| tristate "GPIO 1-wire busmaster" | |
| depends on GPIOLIB || COMPILE_TEST | |
| help | |
| Say Y here if you want to communicate with your 1-wire devices using | |
| GPIO pins. This driver uses the GPIO API to control the wire. | |
| This support is also available as a module. If so, the module | |
| will be called w1-gpio. | |
| config HDQ_MASTER_OMAP | |
| tristate "OMAP HDQ driver" | |
| depends on ARCH_OMAP || COMPILE_TEST | |
| help | |
| Say Y here if you want support for the 1-wire or HDQ Interface | |
| on an OMAP processor. | |
| config W1_MASTER_SGI | |
| tristate "SGI ASIC driver" | |
| help | |
| Say Y here if you want support for your 1-wire devices using | |
| SGI ASIC 1-Wire interface | |
| This support is also available as a module. If so, the module | |
| will be called sgi_w1. | |
| config W1_MASTER_UART | |
| tristate "UART 1-wire driver" | |
| depends on SERIAL_DEV_BUS | |
| help | |
| Say Y here if you want to communicate with your 1-wire devices using | |
| UART interface. | |
| This support is also available as a module. If so, the module | |
| will be called w1-uart. | |
| endmenu | |