| // SPDX-License-Identifier: GPL-2.0 | |
| /* NXP TJA1100 BroadRReach PHY driver | |
| * | |
| * Copyright (C) 2018 Marek Vasut <marex@denx.de> | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/ethtool.h> | |
| #include <linux/ethtool_netlink.h> | |
| #include <linux/kernel.h> | |
| #include <linux/mdio.h> | |
| #include <linux/mii.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/phy.h> | |
| #include <linux/hwmon.h> | |
| #include <linux/bitfield.h> | |
| #include <linux/of_mdio.h> | |
| #include <linux/of_irq.h> | |
| #define PHY_ID_MASK 0xfffffff0 | |
| #define PHY_ID_TJA1100 0x0180dc40 | |
| #define PHY_ID_TJA1101 0x0180dd00 | |
| #define PHY_ID_TJA1102 0x0180dc80 | |
| #define PHY_ID_TJA1102S 0x0180dc90 | |
| #define MII_ECTRL 17 | |
| #define MII_ECTRL_LINK_CONTROL BIT(15) | |
| #define MII_ECTRL_POWER_MODE_MASK GENMASK(14, 11) | |
| #define MII_ECTRL_POWER_MODE_NO_CHANGE (0x0 << 11) | |
| #define MII_ECTRL_POWER_MODE_NORMAL (0x3 << 11) | |
| #define MII_ECTRL_POWER_MODE_SLEEP (0xa << 11) | |
| #define MII_ECTRL_POWER_MODE_STANDBY (0xc << 11) | |
| #define MII_ECTRL_CABLE_TEST BIT(5) | |
| #define MII_ECTRL_CONFIG_EN BIT(2) | |
| #define MII_ECTRL_WAKE_REQUEST BIT(0) | |
| #define MII_CFG1 18 | |
| #define MII_CFG1_MASTER_SLAVE BIT(15) | |
| #define MII_CFG1_AUTO_OP BIT(14) | |
| #define MII_CFG1_INTERFACE_MODE_MASK GENMASK(9, 8) | |
| #define MII_CFG1_MII_MODE (0x0 << 8) | |
| #define MII_CFG1_RMII_MODE_REFCLK_IN BIT(8) | |
| #define MII_CFG1_RMII_MODE_REFCLK_OUT BIT(9) | |
| #define MII_CFG1_REVMII_MODE GENMASK(9, 8) | |
| #define MII_CFG1_SLEEP_CONFIRM BIT(6) | |
| #define MII_CFG1_LED_MODE_MASK GENMASK(5, 4) | |
| #define MII_CFG1_LED_MODE_LINKUP 0 | |
| #define MII_CFG1_LED_ENABLE BIT(3) | |
| #define MII_CFG2 19 | |
| #define MII_CFG2_SLEEP_REQUEST_TO GENMASK(1, 0) | |
| #define MII_CFG2_SLEEP_REQUEST_TO_16MS 0x3 | |
| #define MII_INTSRC 21 | |
| #define MII_INTSRC_LINK_FAIL BIT(10) | |
| #define MII_INTSRC_LINK_UP BIT(9) | |
| #define MII_INTSRC_MASK (MII_INTSRC_LINK_FAIL | MII_INTSRC_LINK_UP) | |
| #define MII_INTSRC_UV_ERR BIT(3) | |
| #define MII_INTSRC_TEMP_ERR BIT(1) | |
| #define MII_INTEN 22 | |
| #define MII_INTEN_LINK_FAIL BIT(10) | |
| #define MII_INTEN_LINK_UP BIT(9) | |
| #define MII_INTEN_UV_ERR BIT(3) | |
| #define MII_INTEN_TEMP_ERR BIT(1) | |
| #define MII_COMMSTAT 23 | |
| #define MII_COMMSTAT_LINK_UP BIT(15) | |
| #define MII_COMMSTAT_SQI_STATE GENMASK(7, 5) | |
| #define MII_COMMSTAT_SQI_MAX 7 | |
| #define MII_GENSTAT 24 | |
| #define MII_GENSTAT_PLL_LOCKED BIT(14) | |
| #define MII_EXTSTAT 25 | |
| #define MII_EXTSTAT_SHORT_DETECT BIT(8) | |
| #define MII_EXTSTAT_OPEN_DETECT BIT(7) | |
| #define MII_EXTSTAT_POLARITY_DETECT BIT(6) | |
| #define MII_COMMCFG 27 | |
| #define MII_COMMCFG_AUTO_OP BIT(15) | |
| #define MII_CFG3 28 | |
| #define MII_CFG3_PHY_EN BIT(0) | |
| /* Configure REF_CLK as input in RMII mode */ | |
| #define TJA110X_RMII_MODE_REFCLK_IN BIT(0) | |
| struct tja11xx_priv { | |
| struct phy_device *phydev; | |
| struct work_struct phy_register_work; | |
| u32 flags; | |
| }; | |
| struct tja11xx_phy_stats { | |
| const char *string; | |
| u8 reg; | |
| u8 off; | |
| u16 mask; | |
| }; | |
| static struct tja11xx_phy_stats tja11xx_hw_stats[] = { | |
| { "phy_symbol_error_count", 20, 0, GENMASK(15, 0) }, | |
| { "phy_polarity_detect", 25, 6, BIT(6) }, | |
| { "phy_open_detect", 25, 7, BIT(7) }, | |
| { "phy_short_detect", 25, 8, BIT(8) }, | |
| { "phy_rem_rcvr_count", 26, 0, GENMASK(7, 0) }, | |
| { "phy_loc_rcvr_count", 26, 8, GENMASK(15, 8) }, | |
| }; | |
| static int tja11xx_check(struct phy_device *phydev, u8 reg, u16 mask, u16 set) | |
| { | |
| int val; | |
| return phy_read_poll_timeout(phydev, reg, val, (val & mask) == set, | |
| 150, 30000, false); | |
| } | |
| static int phy_modify_check(struct phy_device *phydev, u8 reg, | |
| u16 mask, u16 set) | |
| { | |
| int ret; | |
| ret = phy_modify(phydev, reg, mask, set); | |
| if (ret) | |
| return ret; | |
| return tja11xx_check(phydev, reg, mask, set); | |
| } | |
| static int tja11xx_enable_reg_write(struct phy_device *phydev) | |
| { | |
| return phy_set_bits(phydev, MII_ECTRL, MII_ECTRL_CONFIG_EN); | |
| } | |
| static int tja11xx_enable_link_control(struct phy_device *phydev) | |
| { | |
| return phy_set_bits(phydev, MII_ECTRL, MII_ECTRL_LINK_CONTROL); | |
| } | |
| static int tja11xx_disable_link_control(struct phy_device *phydev) | |
| { | |
| return phy_clear_bits(phydev, MII_ECTRL, MII_ECTRL_LINK_CONTROL); | |
| } | |
| static int tja11xx_wakeup(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = phy_read(phydev, MII_ECTRL); | |
| if (ret < 0) | |
| return ret; | |
| switch (ret & MII_ECTRL_POWER_MODE_MASK) { | |
| case MII_ECTRL_POWER_MODE_NO_CHANGE: | |
| break; | |
| case MII_ECTRL_POWER_MODE_NORMAL: | |
| ret = phy_set_bits(phydev, MII_ECTRL, MII_ECTRL_WAKE_REQUEST); | |
| if (ret) | |
| return ret; | |
| ret = phy_clear_bits(phydev, MII_ECTRL, MII_ECTRL_WAKE_REQUEST); | |
| if (ret) | |
| return ret; | |
| break; | |
| case MII_ECTRL_POWER_MODE_STANDBY: | |
| ret = phy_modify_check(phydev, MII_ECTRL, | |
| MII_ECTRL_POWER_MODE_MASK, | |
| MII_ECTRL_POWER_MODE_STANDBY); | |
| if (ret) | |
| return ret; | |
| ret = phy_modify(phydev, MII_ECTRL, MII_ECTRL_POWER_MODE_MASK, | |
| MII_ECTRL_POWER_MODE_NORMAL); | |
| if (ret) | |
| return ret; | |
| ret = phy_modify_check(phydev, MII_GENSTAT, | |
| MII_GENSTAT_PLL_LOCKED, | |
| MII_GENSTAT_PLL_LOCKED); | |
| if (ret) | |
| return ret; | |
| return tja11xx_enable_link_control(phydev); | |
| case MII_ECTRL_POWER_MODE_SLEEP: | |
| switch (phydev->phy_id & PHY_ID_MASK) { | |
| case PHY_ID_TJA1102S: | |
| /* Enable PHY, maybe it is disabled due to pin strapping */ | |
| return phy_set_bits(phydev, MII_CFG3, MII_CFG3_PHY_EN); | |
| default: | |
| return 0; | |
| } | |
| default: | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int tja11xx_soft_reset(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = tja11xx_enable_reg_write(phydev); | |
| if (ret) | |
| return ret; | |
| return genphy_soft_reset(phydev); | |
| } | |
| static int tja11xx_config_aneg_cable_test(struct phy_device *phydev) | |
| { | |
| bool finished = false; | |
| int ret; | |
| if (phydev->link) | |
| return 0; | |
| if (!phydev->drv->cable_test_start || | |
| !phydev->drv->cable_test_get_status) | |
| return 0; | |
| ret = ethnl_cable_test_alloc(phydev, ETHTOOL_MSG_CABLE_TEST_NTF); | |
| if (ret) | |
| return ret; | |
| ret = phydev->drv->cable_test_start(phydev); | |
| if (ret) | |
| return ret; | |
| /* According to the documentation this test takes 100 usec */ | |
| usleep_range(100, 200); | |
| ret = phydev->drv->cable_test_get_status(phydev, &finished); | |
| if (ret) | |
| return ret; | |
| if (finished) | |
| ethnl_cable_test_finished(phydev); | |
| return 0; | |
| } | |
| static int tja11xx_config_aneg(struct phy_device *phydev) | |
| { | |
| int ret, changed = 0; | |
| u16 ctl = 0; | |
| switch (phydev->master_slave_set) { | |
| case MASTER_SLAVE_CFG_MASTER_FORCE: | |
| ctl |= MII_CFG1_MASTER_SLAVE; | |
| break; | |
| case MASTER_SLAVE_CFG_SLAVE_FORCE: | |
| break; | |
| case MASTER_SLAVE_CFG_UNKNOWN: | |
| case MASTER_SLAVE_CFG_UNSUPPORTED: | |
| goto do_test; | |
| default: | |
| phydev_warn(phydev, "Unsupported Master/Slave mode\n"); | |
| return -ENOTSUPP; | |
| } | |
| changed = phy_modify_changed(phydev, MII_CFG1, MII_CFG1_MASTER_SLAVE, ctl); | |
| if (changed < 0) | |
| return changed; | |
| do_test: | |
| ret = tja11xx_config_aneg_cable_test(phydev); | |
| if (ret) | |
| return ret; | |
| return __genphy_config_aneg(phydev, changed); | |
| } | |
| static int tja11xx_get_interface_mode(struct phy_device *phydev) | |
| { | |
| struct tja11xx_priv *priv = phydev->priv; | |
| int mii_mode; | |
| switch (phydev->interface) { | |
| case PHY_INTERFACE_MODE_MII: | |
| mii_mode = MII_CFG1_MII_MODE; | |
| break; | |
| case PHY_INTERFACE_MODE_REVMII: | |
| mii_mode = MII_CFG1_REVMII_MODE; | |
| break; | |
| case PHY_INTERFACE_MODE_RMII: | |
| if (priv->flags & TJA110X_RMII_MODE_REFCLK_IN) | |
| mii_mode = MII_CFG1_RMII_MODE_REFCLK_IN; | |
| else | |
| mii_mode = MII_CFG1_RMII_MODE_REFCLK_OUT; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return mii_mode; | |
| } | |
| static int tja11xx_config_init(struct phy_device *phydev) | |
| { | |
| u16 reg_mask, reg_val; | |
| int ret; | |
| ret = tja11xx_enable_reg_write(phydev); | |
| if (ret) | |
| return ret; | |
| phydev->autoneg = AUTONEG_DISABLE; | |
| phydev->speed = SPEED_100; | |
| phydev->duplex = DUPLEX_FULL; | |
| switch (phydev->phy_id & PHY_ID_MASK) { | |
| case PHY_ID_TJA1100: | |
| reg_mask = MII_CFG1_AUTO_OP | MII_CFG1_LED_MODE_MASK | | |
| MII_CFG1_LED_ENABLE; | |
| reg_val = MII_CFG1_AUTO_OP | MII_CFG1_LED_MODE_LINKUP | | |
| MII_CFG1_LED_ENABLE; | |
| reg_mask |= MII_CFG1_INTERFACE_MODE_MASK; | |
| ret = tja11xx_get_interface_mode(phydev); | |
| if (ret < 0) | |
| return ret; | |
| reg_val |= (ret & 0xffff); | |
| ret = phy_modify(phydev, MII_CFG1, reg_mask, reg_val); | |
| if (ret) | |
| return ret; | |
| break; | |
| case PHY_ID_TJA1102S: | |
| case PHY_ID_TJA1101: | |
| reg_mask = MII_CFG1_INTERFACE_MODE_MASK; | |
| ret = tja11xx_get_interface_mode(phydev); | |
| if (ret < 0) | |
| return ret; | |
| reg_val = ret & 0xffff; | |
| ret = phy_modify(phydev, MII_CFG1, reg_mask, reg_val); | |
| if (ret) | |
| return ret; | |
| fallthrough; | |
| case PHY_ID_TJA1102: | |
| ret = phy_set_bits(phydev, MII_COMMCFG, MII_COMMCFG_AUTO_OP); | |
| if (ret) | |
| return ret; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| ret = phy_clear_bits(phydev, MII_CFG1, MII_CFG1_SLEEP_CONFIRM); | |
| if (ret) | |
| return ret; | |
| ret = phy_modify(phydev, MII_CFG2, MII_CFG2_SLEEP_REQUEST_TO, | |
| MII_CFG2_SLEEP_REQUEST_TO_16MS); | |
| if (ret) | |
| return ret; | |
| ret = tja11xx_wakeup(phydev); | |
| if (ret < 0) | |
| return ret; | |
| /* ACK interrupts by reading the status register */ | |
| ret = phy_read(phydev, MII_INTSRC); | |
| if (ret < 0) | |
| return ret; | |
| return 0; | |
| } | |
| static int tja11xx_read_status(struct phy_device *phydev) | |
| { | |
| int ret; | |
| phydev->master_slave_get = MASTER_SLAVE_CFG_UNKNOWN; | |
| phydev->master_slave_state = MASTER_SLAVE_STATE_UNSUPPORTED; | |
| ret = genphy_update_link(phydev); | |
| if (ret) | |
| return ret; | |
| ret = phy_read(phydev, MII_CFG1); | |
| if (ret < 0) | |
| return ret; | |
| if (ret & MII_CFG1_MASTER_SLAVE) | |
| phydev->master_slave_get = MASTER_SLAVE_CFG_MASTER_FORCE; | |
| else | |
| phydev->master_slave_get = MASTER_SLAVE_CFG_SLAVE_FORCE; | |
| if (phydev->link) { | |
| ret = phy_read(phydev, MII_COMMSTAT); | |
| if (ret < 0) | |
| return ret; | |
| if (!(ret & MII_COMMSTAT_LINK_UP)) | |
| phydev->link = 0; | |
| } | |
| return 0; | |
| } | |
| static int tja11xx_get_sqi(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = phy_read(phydev, MII_COMMSTAT); | |
| if (ret < 0) | |
| return ret; | |
| return FIELD_GET(MII_COMMSTAT_SQI_STATE, ret); | |
| } | |
| static int tja11xx_get_sqi_max(struct phy_device *phydev) | |
| { | |
| return MII_COMMSTAT_SQI_MAX; | |
| } | |
| static int tja11xx_get_sset_count(struct phy_device *phydev) | |
| { | |
| return ARRAY_SIZE(tja11xx_hw_stats); | |
| } | |
| static void tja11xx_get_strings(struct phy_device *phydev, u8 *data) | |
| { | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(tja11xx_hw_stats); i++) | |
| ethtool_puts(&data, tja11xx_hw_stats[i].string); | |
| } | |
| static void tja11xx_get_stats(struct phy_device *phydev, | |
| struct ethtool_stats *stats, u64 *data) | |
| { | |
| int i, ret; | |
| for (i = 0; i < ARRAY_SIZE(tja11xx_hw_stats); i++) { | |
| ret = phy_read(phydev, tja11xx_hw_stats[i].reg); | |
| if (ret < 0) | |
| data[i] = U64_MAX; | |
| else { | |
| data[i] = ret & tja11xx_hw_stats[i].mask; | |
| data[i] >>= tja11xx_hw_stats[i].off; | |
| } | |
| } | |
| } | |
| static int tja11xx_hwmon_read(struct device *dev, | |
| enum hwmon_sensor_types type, | |
| u32 attr, int channel, long *value) | |
| { | |
| struct phy_device *phydev = dev_get_drvdata(dev); | |
| int ret; | |
| if (type == hwmon_in && attr == hwmon_in_lcrit_alarm) { | |
| ret = phy_read(phydev, MII_INTSRC); | |
| if (ret < 0) | |
| return ret; | |
| *value = !!(ret & MII_INTSRC_TEMP_ERR); | |
| return 0; | |
| } | |
| if (type == hwmon_temp && attr == hwmon_temp_crit_alarm) { | |
| ret = phy_read(phydev, MII_INTSRC); | |
| if (ret < 0) | |
| return ret; | |
| *value = !!(ret & MII_INTSRC_UV_ERR); | |
| return 0; | |
| } | |
| return -EOPNOTSUPP; | |
| } | |
| static umode_t tja11xx_hwmon_is_visible(const void *data, | |
| enum hwmon_sensor_types type, | |
| u32 attr, int channel) | |
| { | |
| if (type == hwmon_in && attr == hwmon_in_lcrit_alarm) | |
| return 0444; | |
| if (type == hwmon_temp && attr == hwmon_temp_crit_alarm) | |
| return 0444; | |
| return 0; | |
| } | |
| static const struct hwmon_channel_info * const tja11xx_hwmon_info[] = { | |
| HWMON_CHANNEL_INFO(in, HWMON_I_LCRIT_ALARM), | |
| HWMON_CHANNEL_INFO(temp, HWMON_T_CRIT_ALARM), | |
| NULL | |
| }; | |
| static const struct hwmon_ops tja11xx_hwmon_hwmon_ops = { | |
| .is_visible = tja11xx_hwmon_is_visible, | |
| .read = tja11xx_hwmon_read, | |
| }; | |
| static const struct hwmon_chip_info tja11xx_hwmon_chip_info = { | |
| .ops = &tja11xx_hwmon_hwmon_ops, | |
| .info = tja11xx_hwmon_info, | |
| }; | |
| static int tja11xx_hwmon_register(struct phy_device *phydev, | |
| struct tja11xx_priv *priv) | |
| { | |
| struct device *hdev, *dev = &phydev->mdio.dev; | |
| hdev = devm_hwmon_device_register_with_info(dev, NULL, phydev, | |
| &tja11xx_hwmon_chip_info, | |
| NULL); | |
| return PTR_ERR_OR_ZERO(hdev); | |
| } | |
| static int tja11xx_parse_dt(struct phy_device *phydev) | |
| { | |
| struct device_node *node = phydev->mdio.dev.of_node; | |
| struct tja11xx_priv *priv = phydev->priv; | |
| if (!IS_ENABLED(CONFIG_OF_MDIO)) | |
| return 0; | |
| if (of_property_read_bool(node, "nxp,rmii-refclk-in")) | |
| priv->flags |= TJA110X_RMII_MODE_REFCLK_IN; | |
| return 0; | |
| } | |
| static int tja11xx_probe(struct phy_device *phydev) | |
| { | |
| struct device *dev = &phydev->mdio.dev; | |
| struct tja11xx_priv *priv; | |
| int ret; | |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); | |
| if (!priv) | |
| return -ENOMEM; | |
| priv->phydev = phydev; | |
| phydev->priv = priv; | |
| ret = tja11xx_parse_dt(phydev); | |
| if (ret) | |
| return ret; | |
| return tja11xx_hwmon_register(phydev, priv); | |
| } | |
| static void tja1102_p1_register(struct work_struct *work) | |
| { | |
| struct tja11xx_priv *priv = container_of(work, struct tja11xx_priv, | |
| phy_register_work); | |
| struct phy_device *phydev_phy0 = priv->phydev; | |
| struct mii_bus *bus = phydev_phy0->mdio.bus; | |
| struct device *dev = &phydev_phy0->mdio.dev; | |
| struct device_node *np = dev->of_node; | |
| struct device_node *child; | |
| int ret; | |
| for_each_available_child_of_node(np, child) { | |
| struct phy_device *phy; | |
| int addr; | |
| addr = of_mdio_parse_addr(dev, child); | |
| if (addr < 0) { | |
| dev_err(dev, "Can't parse addr\n"); | |
| continue; | |
| } else if (addr != phydev_phy0->mdio.addr + 1) { | |
| /* Currently we care only about double PHY chip TJA1102. | |
| * If some day NXP will decide to bring chips with more | |
| * PHYs, this logic should be reworked. | |
| */ | |
| dev_err(dev, "Unexpected address. Should be: %i\n", | |
| phydev_phy0->mdio.addr + 1); | |
| continue; | |
| } | |
| if (mdiobus_is_registered_device(bus, addr)) { | |
| dev_err(dev, "device is already registered\n"); | |
| continue; | |
| } | |
| /* Real PHY ID of Port 1 is 0 */ | |
| phy = phy_device_create(bus, addr, PHY_ID_TJA1102, false, NULL); | |
| if (IS_ERR(phy)) { | |
| dev_err(dev, "Can't create PHY device for Port 1: %i\n", | |
| addr); | |
| continue; | |
| } | |
| /* Overwrite parent device. phy_device_create() set parent to | |
| * the mii_bus->dev, which is not correct in case. | |
| */ | |
| phy->mdio.dev.parent = dev; | |
| ret = of_mdiobus_phy_device_register(bus, phy, child, addr); | |
| if (ret) { | |
| /* All resources needed for Port 1 should be already | |
| * available for Port 0. Both ports use the same | |
| * interrupt line, so -EPROBE_DEFER would make no sense | |
| * here. | |
| */ | |
| dev_err(dev, "Can't register Port 1. Unexpected error: %i\n", | |
| ret); | |
| phy_device_free(phy); | |
| } | |
| } | |
| } | |
| static int tja1102_p0_probe(struct phy_device *phydev) | |
| { | |
| struct device *dev = &phydev->mdio.dev; | |
| struct tja11xx_priv *priv; | |
| int ret; | |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); | |
| if (!priv) | |
| return -ENOMEM; | |
| priv->phydev = phydev; | |
| phydev->priv = priv; | |
| INIT_WORK(&priv->phy_register_work, tja1102_p1_register); | |
| ret = tja11xx_hwmon_register(phydev, priv); | |
| if (ret) | |
| return ret; | |
| schedule_work(&priv->phy_register_work); | |
| return 0; | |
| } | |
| static void tja1102_p0_remove(struct phy_device *phydev) | |
| { | |
| struct tja11xx_priv *priv = phydev->priv; | |
| cancel_work_sync(&priv->phy_register_work); | |
| } | |
| static int tja1102_match_phy_device(struct phy_device *phydev, bool port0) | |
| { | |
| int ret; | |
| if ((phydev->phy_id & PHY_ID_MASK) != PHY_ID_TJA1102) | |
| return 0; | |
| ret = phy_read(phydev, MII_PHYSID2); | |
| if (ret < 0) | |
| return ret; | |
| /* TJA1102 Port 1 has phyid 0 and doesn't support temperature | |
| * and undervoltage alarms. | |
| */ | |
| if (port0) | |
| return ret ? 1 : 0; | |
| return !ret; | |
| } | |
| static int tja1102_p0_match_phy_device(struct phy_device *phydev, | |
| const struct phy_driver *phydrv) | |
| { | |
| return tja1102_match_phy_device(phydev, true); | |
| } | |
| static int tja1102_p1_match_phy_device(struct phy_device *phydev, | |
| const struct phy_driver *phydrv) | |
| { | |
| return tja1102_match_phy_device(phydev, false); | |
| } | |
| static int tja11xx_ack_interrupt(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = phy_read(phydev, MII_INTSRC); | |
| return (ret < 0) ? ret : 0; | |
| } | |
| static int tja11xx_config_intr(struct phy_device *phydev) | |
| { | |
| int value = 0; | |
| int err; | |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { | |
| err = tja11xx_ack_interrupt(phydev); | |
| if (err) | |
| return err; | |
| value = MII_INTEN_LINK_FAIL | MII_INTEN_LINK_UP | | |
| MII_INTEN_UV_ERR | MII_INTEN_TEMP_ERR; | |
| err = phy_write(phydev, MII_INTEN, value); | |
| } else { | |
| err = phy_write(phydev, MII_INTEN, value); | |
| if (err) | |
| return err; | |
| err = tja11xx_ack_interrupt(phydev); | |
| } | |
| return err; | |
| } | |
| static irqreturn_t tja11xx_handle_interrupt(struct phy_device *phydev) | |
| { | |
| struct device *dev = &phydev->mdio.dev; | |
| int irq_status; | |
| irq_status = phy_read(phydev, MII_INTSRC); | |
| if (irq_status < 0) { | |
| phy_error(phydev); | |
| return IRQ_NONE; | |
| } | |
| if (irq_status & MII_INTSRC_TEMP_ERR) | |
| dev_warn(dev, "Overtemperature error detected (temp > 155C°).\n"); | |
| if (irq_status & MII_INTSRC_UV_ERR) | |
| dev_warn(dev, "Undervoltage error detected.\n"); | |
| if (!(irq_status & MII_INTSRC_MASK)) | |
| return IRQ_NONE; | |
| phy_trigger_machine(phydev); | |
| return IRQ_HANDLED; | |
| } | |
| static int tja11xx_cable_test_start(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = phy_clear_bits(phydev, MII_COMMCFG, MII_COMMCFG_AUTO_OP); | |
| if (ret) | |
| return ret; | |
| ret = tja11xx_wakeup(phydev); | |
| if (ret < 0) | |
| return ret; | |
| ret = tja11xx_disable_link_control(phydev); | |
| if (ret < 0) | |
| return ret; | |
| return phy_set_bits(phydev, MII_ECTRL, MII_ECTRL_CABLE_TEST); | |
| } | |
| /* | |
| * | BI_DA+ | BI_DA- | Result | |
| * | open | open | open | |
| * | + short to - | - short to + | short | |
| * | short to Vdd | open | open | |
| * | open | shot to Vdd | open | |
| * | short to Vdd | short to Vdd | short | |
| * | shot to GND | open | open | |
| * | open | shot to GND | open | |
| * | short to GND | shot to GND | short | |
| * | connected to active link partner (master) | shot and open | |
| */ | |
| static int tja11xx_cable_test_report_trans(u32 result) | |
| { | |
| u32 mask = MII_EXTSTAT_SHORT_DETECT | MII_EXTSTAT_OPEN_DETECT; | |
| if ((result & mask) == mask) { | |
| /* connected to active link partner (master) */ | |
| return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; | |
| } else if ((result & mask) == 0) { | |
| return ETHTOOL_A_CABLE_RESULT_CODE_OK; | |
| } else if (result & MII_EXTSTAT_SHORT_DETECT) { | |
| return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; | |
| } else if (result & MII_EXTSTAT_OPEN_DETECT) { | |
| return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; | |
| } else { | |
| return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; | |
| } | |
| } | |
| static int tja11xx_cable_test_report(struct phy_device *phydev) | |
| { | |
| int ret; | |
| ret = phy_read(phydev, MII_EXTSTAT); | |
| if (ret < 0) | |
| return ret; | |
| ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A, | |
| tja11xx_cable_test_report_trans(ret)); | |
| return 0; | |
| } | |
| static int tja11xx_cable_test_get_status(struct phy_device *phydev, | |
| bool *finished) | |
| { | |
| int ret; | |
| *finished = false; | |
| ret = phy_read(phydev, MII_ECTRL); | |
| if (ret < 0) | |
| return ret; | |
| if (!(ret & MII_ECTRL_CABLE_TEST)) { | |
| *finished = true; | |
| ret = phy_set_bits(phydev, MII_COMMCFG, MII_COMMCFG_AUTO_OP); | |
| if (ret) | |
| return ret; | |
| return tja11xx_cable_test_report(phydev); | |
| } | |
| return 0; | |
| } | |
| static struct phy_driver tja11xx_driver[] = { | |
| { | |
| PHY_ID_MATCH_MODEL(PHY_ID_TJA1100), | |
| .name = "NXP TJA1100", | |
| .features = PHY_BASIC_T1_FEATURES, | |
| .probe = tja11xx_probe, | |
| .soft_reset = tja11xx_soft_reset, | |
| .config_aneg = tja11xx_config_aneg, | |
| .config_init = tja11xx_config_init, | |
| .read_status = tja11xx_read_status, | |
| .get_sqi = tja11xx_get_sqi, | |
| .get_sqi_max = tja11xx_get_sqi_max, | |
| .suspend = genphy_suspend, | |
| .resume = genphy_resume, | |
| .set_loopback = genphy_loopback, | |
| /* Statistics */ | |
| .get_sset_count = tja11xx_get_sset_count, | |
| .get_strings = tja11xx_get_strings, | |
| .get_stats = tja11xx_get_stats, | |
| }, { | |
| PHY_ID_MATCH_MODEL(PHY_ID_TJA1101), | |
| .name = "NXP TJA1101", | |
| .features = PHY_BASIC_T1_FEATURES, | |
| .probe = tja11xx_probe, | |
| .soft_reset = tja11xx_soft_reset, | |
| .config_aneg = tja11xx_config_aneg, | |
| .config_init = tja11xx_config_init, | |
| .read_status = tja11xx_read_status, | |
| .get_sqi = tja11xx_get_sqi, | |
| .get_sqi_max = tja11xx_get_sqi_max, | |
| .suspend = genphy_suspend, | |
| .resume = genphy_resume, | |
| .set_loopback = genphy_loopback, | |
| /* Statistics */ | |
| .get_sset_count = tja11xx_get_sset_count, | |
| .get_strings = tja11xx_get_strings, | |
| .get_stats = tja11xx_get_stats, | |
| }, { | |
| .name = "NXP TJA1102 Port 0", | |
| .features = PHY_BASIC_T1_FEATURES, | |
| .flags = PHY_POLL_CABLE_TEST, | |
| .probe = tja1102_p0_probe, | |
| .remove = tja1102_p0_remove, | |
| .soft_reset = tja11xx_soft_reset, | |
| .config_aneg = tja11xx_config_aneg, | |
| .config_init = tja11xx_config_init, | |
| .read_status = tja11xx_read_status, | |
| .get_sqi = tja11xx_get_sqi, | |
| .get_sqi_max = tja11xx_get_sqi_max, | |
| .match_phy_device = tja1102_p0_match_phy_device, | |
| .suspend = genphy_suspend, | |
| .resume = genphy_resume, | |
| .set_loopback = genphy_loopback, | |
| /* Statistics */ | |
| .get_sset_count = tja11xx_get_sset_count, | |
| .get_strings = tja11xx_get_strings, | |
| .get_stats = tja11xx_get_stats, | |
| .config_intr = tja11xx_config_intr, | |
| .handle_interrupt = tja11xx_handle_interrupt, | |
| .cable_test_start = tja11xx_cable_test_start, | |
| .cable_test_get_status = tja11xx_cable_test_get_status, | |
| }, { | |
| .name = "NXP TJA1102 Port 1", | |
| .features = PHY_BASIC_T1_FEATURES, | |
| .flags = PHY_POLL_CABLE_TEST, | |
| /* currently no probe for Port 1 is need */ | |
| .soft_reset = tja11xx_soft_reset, | |
| .config_aneg = tja11xx_config_aneg, | |
| .config_init = tja11xx_config_init, | |
| .read_status = tja11xx_read_status, | |
| .get_sqi = tja11xx_get_sqi, | |
| .get_sqi_max = tja11xx_get_sqi_max, | |
| .match_phy_device = tja1102_p1_match_phy_device, | |
| .suspend = genphy_suspend, | |
| .resume = genphy_resume, | |
| .set_loopback = genphy_loopback, | |
| /* Statistics */ | |
| .get_sset_count = tja11xx_get_sset_count, | |
| .get_strings = tja11xx_get_strings, | |
| .get_stats = tja11xx_get_stats, | |
| .config_intr = tja11xx_config_intr, | |
| .handle_interrupt = tja11xx_handle_interrupt, | |
| .cable_test_start = tja11xx_cable_test_start, | |
| .cable_test_get_status = tja11xx_cable_test_get_status, | |
| }, { | |
| PHY_ID_MATCH_MODEL(PHY_ID_TJA1102S), | |
| .name = "NXP TJA1102S", | |
| .features = PHY_BASIC_T1_FEATURES, | |
| .flags = PHY_POLL_CABLE_TEST, | |
| .probe = tja11xx_probe, | |
| .soft_reset = tja11xx_soft_reset, | |
| .config_aneg = tja11xx_config_aneg, | |
| .config_init = tja11xx_config_init, | |
| .read_status = tja11xx_read_status, | |
| .get_sqi = tja11xx_get_sqi, | |
| .get_sqi_max = tja11xx_get_sqi_max, | |
| .suspend = genphy_suspend, | |
| .resume = genphy_resume, | |
| .set_loopback = genphy_loopback, | |
| /* Statistics */ | |
| .get_sset_count = tja11xx_get_sset_count, | |
| .get_strings = tja11xx_get_strings, | |
| .get_stats = tja11xx_get_stats, | |
| .config_intr = tja11xx_config_intr, | |
| .handle_interrupt = tja11xx_handle_interrupt, | |
| .cable_test_start = tja11xx_cable_test_start, | |
| .cable_test_get_status = tja11xx_cable_test_get_status, | |
| } | |
| }; | |
| module_phy_driver(tja11xx_driver); | |
| static const struct mdio_device_id __maybe_unused tja11xx_tbl[] = { | |
| { PHY_ID_MATCH_MODEL(PHY_ID_TJA1100) }, | |
| { PHY_ID_MATCH_MODEL(PHY_ID_TJA1101) }, | |
| { PHY_ID_MATCH_MODEL(PHY_ID_TJA1102) }, | |
| { PHY_ID_MATCH_MODEL(PHY_ID_TJA1102S) }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(mdio, tja11xx_tbl); | |
| MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); | |
| MODULE_DESCRIPTION("NXP TJA11xx BoardR-Reach PHY driver"); | |
| MODULE_LICENSE("GPL"); |