| # SPDX-License-Identifier: GPL-2.0-only | |
| # | |
| # Realtek device configuration | |
| # | |
| config NET_VENDOR_REALTEK | |
| bool "Realtek devices" | |
| default y | |
| depends on PCI | |
| help | |
| If you have a network (Ethernet) card belonging to this class, say Y. | |
| Note that the answer to this question doesn't directly affect the | |
| kernel: saying N will just cause the configurator to skip all | |
| the questions about Realtek devices. If you say Y, you will be asked for | |
| your specific card in the following questions. | |
| if NET_VENDOR_REALTEK | |
| config 8139CP | |
| tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support" | |
| depends on PCI | |
| select CRC32 | |
| select MII | |
| help | |
| This is a driver for the Fast Ethernet PCI network cards based on | |
| the RTL8139C+ chips. If you have one of those, say Y here. | |
| To compile this driver as a module, choose M here: the module | |
| will be called 8139cp. This is recommended. | |
| config 8139TOO | |
| tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" | |
| depends on PCI | |
| select CRC32 | |
| select MII | |
| help | |
| This is a driver for the Fast Ethernet PCI network cards based on | |
| the RTL 8129/8130/8139 chips. If you have one of those, say Y here. | |
| To compile this driver as a module, choose M here: the module | |
| will be called 8139too. This is recommended. | |
| config 8139TOO_PIO | |
| bool "Use PIO instead of MMIO" | |
| default y | |
| depends on 8139TOO && !NO_IOPORT_MAP | |
| help | |
| This instructs the driver to use programmed I/O ports (PIO) instead | |
| of PCI shared memory (MMIO). This can possibly solve some problems | |
| in case your mainboard has memory consistency issues. If unsure, | |
| say N. | |
| config 8139TOO_TUNE_TWISTER | |
| bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" | |
| depends on 8139TOO | |
| help | |
| This implements a function which might come in handy in case you | |
| are using low quality on long cabling. It is required for RealTek | |
| RTL-8139 revision K boards, and totally unused otherwise. It tries | |
| to match the transceiver to the cable characteristics. This is | |
| experimental since hardly documented by the manufacturer. | |
| If unsure, say Y. | |
| config 8139TOO_8129 | |
| bool "Support for older RTL-8129/8130 boards" | |
| depends on 8139TOO | |
| help | |
| This enables support for the older and uncommon RTL-8129 and | |
| RTL-8130 chips, which support MII via an external transceiver, | |
| instead of an internal one. Disabling this option will save some | |
| memory by making the code size smaller. If unsure, say Y. | |
| config 8139_OLD_RX_RESET | |
| bool "Use older RX-reset method" | |
| depends on 8139TOO | |
| help | |
| The 8139too driver was recently updated to contain a more rapid | |
| reset sequence, in the face of severe receive errors. This "new" | |
| RX-reset method should be adequate for all boards. But if you | |
| experience problems, you can enable this option to restore the | |
| old RX-reset behavior. If unsure, say N. | |
| config R8169 | |
| tristate "Realtek 8169/8168/8101/8125 ethernet support" | |
| depends on PCI | |
| select FW_LOADER | |
| select CRC32 | |
| select PHYLIB | |
| select REALTEK_PHY | |
| help | |
| Say Y here if you have a Realtek Ethernet adapter belonging to | |
| the following families: | |
| RTL8169 Gigabit Ethernet | |
| RTL8168 Gigabit Ethernet | |
| RTL8101 Fast Ethernet | |
| RTL8125 2.5GBit Ethernet | |
| To compile this driver as a module, choose M here: the module | |
| will be called r8169. This is recommended. | |
| config R8169_LEDS | |
| bool "Support for controlling the NIC LEDs" | |
| depends on R8169 && LEDS_TRIGGER_NETDEV | |
| depends on !(R8169=y && LEDS_CLASS=m) | |
| help | |
| Optional support for controlling the NIC LED's with the netdev | |
| LED trigger. | |
| config RTASE | |
| tristate "Realtek Automotive Switch 9054/9068/9072/9075/9068/9071 PCIe Interface support" | |
| depends on PCI | |
| select CRC32 | |
| select PAGE_POOL | |
| help | |
| Say Y here and it will be compiled and linked with the kernel | |
| if you have a Realtek Ethernet adapter belonging to the | |
| following families: | |
| RTL9054 5GBit Ethernet | |
| RTL9068 5GBit Ethernet | |
| RTL9072 5GBit Ethernet | |
| RTL9075 5GBit Ethernet | |
| RTL9068 5GBit Ethernet | |
| RTL9071 5GBit Ethernet | |
| To compile this driver as a module, choose M here: the module | |
| will be called rtase. This is recommended. | |
| endif # NET_VENDOR_REALTEK |