| /* SPDX-License-Identifier: GPL-2.0 */ | |
| /* Copyright(c) 1999 - 2018 Intel Corporation. */ | |
| /* Linux PRO/1000 Ethernet Driver main header file */ | |
| #ifndef _E1000_H_ | |
| #define _E1000_H_ | |
| #include <linux/bitops.h> | |
| #include <linux/types.h> | |
| #include <linux/timer.h> | |
| #include <linux/workqueue.h> | |
| #include <linux/io.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/pci.h> | |
| #include <linux/crc32.h> | |
| #include <linux/if_vlan.h> | |
| #include <linux/timecounter.h> | |
| #include <linux/net_tstamp.h> | |
| #include <linux/ptp_clock_kernel.h> | |
| #include <linux/ptp_classify.h> | |
| #include <linux/mii.h> | |
| #include <linux/mdio.h> | |
| #include <linux/mutex.h> | |
| #include <linux/pm_qos.h> | |
| #include "hw.h" | |
| struct e1000_info; | |
| #define e_dbg(format, arg...) \ | |
| netdev_dbg(hw->adapter->netdev, format, ## arg) | |
| #define e_err(format, arg...) \ | |
| netdev_err(adapter->netdev, format, ## arg) | |
| #define e_info(format, arg...) \ | |
| netdev_info(adapter->netdev, format, ## arg) | |
| #define e_warn(format, arg...) \ | |
| netdev_warn(adapter->netdev, format, ## arg) | |
| #define e_notice(format, arg...) \ | |
| netdev_notice(adapter->netdev, format, ## arg) | |
| /* Interrupt modes, as used by the IntMode parameter */ | |
| #define E1000E_INT_MODE_LEGACY 0 | |
| #define E1000E_INT_MODE_MSI 1 | |
| #define E1000E_INT_MODE_MSIX 2 | |
| /* Tx/Rx descriptor defines */ | |
| #define E1000_DEFAULT_TXD 256 | |
| #define E1000_MAX_TXD 4096 | |
| #define E1000_MIN_TXD 64 | |
| #define E1000_DEFAULT_RXD 256 | |
| #define E1000_MAX_RXD 4096 | |
| #define E1000_MIN_RXD 64 | |
| #define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */ | |
| #define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */ | |
| #define E1000_FC_PAUSE_TIME 0x0680 /* 858 usec */ | |
| /* How many Tx Descriptors do we need to call netif_wake_queue ? */ | |
| /* How many Rx Buffers do we bundle into one write to the hardware ? */ | |
| #define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */ | |
| #define AUTO_ALL_MODES 0 | |
| #define E1000_EEPROM_APME 0x0400 | |
| #define E1000_MNG_VLAN_NONE 0xFFFF | |
| #define DEFAULT_JUMBO 9234 | |
| /* Time to wait before putting the device into D3 if there's no link (in ms). */ | |
| #define LINK_TIMEOUT 100 | |
| /* Count for polling __E1000_RESET condition every 10-20msec. | |
| * Experimentation has shown the reset can take approximately 210msec. | |
| */ | |
| #define E1000_CHECK_RESET_COUNT 25 | |
| #define PCICFG_DESC_RING_STATUS 0xe4 | |
| #define FLUSH_DESC_REQUIRED 0x100 | |
| /* in the case of WTHRESH, it appears at least the 82571/2 hardware | |
| * writes back 4 descriptors when WTHRESH=5, and 3 descriptors when | |
| * WTHRESH=4, so a setting of 5 gives the most efficient bus | |
| * utilization but to avoid possible Tx stalls, set it to 1 | |
| */ | |
| #define E1000_TXDCTL_DMA_BURST_ENABLE \ | |
| (E1000_TXDCTL_GRAN | /* set descriptor granularity */ \ | |
| E1000_TXDCTL_COUNT_DESC | \ | |
| (1u << 16) | /* wthresh must be +1 more than desired */\ | |
| (1u << 8) | /* hthresh */ \ | |
| 0x1f) /* pthresh */ | |
| #define E1000_RXDCTL_DMA_BURST_ENABLE \ | |
| (0x01000000 | /* set descriptor granularity */ \ | |
| (4u << 16) | /* set writeback threshold */ \ | |
| (4u << 8) | /* set prefetch threshold */ \ | |
| 0x20) /* set hthresh */ | |
| #define E1000_TIDV_FPD BIT(31) | |
| #define E1000_RDTR_FPD BIT(31) | |
| enum e1000_boards { | |
| board_82571, | |
| board_82572, | |
| board_82573, | |
| board_82574, | |
| board_82583, | |
| board_80003es2lan, | |
| board_ich8lan, | |
| board_ich9lan, | |
| board_ich10lan, | |
| board_pchlan, | |
| board_pch2lan, | |
| board_pch_lpt, | |
| board_pch_spt, | |
| board_pch_cnp, | |
| board_pch_tgp, | |
| board_pch_adp, | |
| board_pch_mtp, | |
| board_pch_ptp | |
| }; | |
| struct e1000_ps_page { | |
| struct page *page; | |
| u64 dma; /* must be u64 - written to hw */ | |
| }; | |
| /* wrappers around a pointer to a socket buffer, | |
| * so a DMA handle can be stored along with the buffer | |
| */ | |
| struct e1000_buffer { | |
| dma_addr_t dma; | |
| struct sk_buff *skb; | |
| union { | |
| /* Tx */ | |
| struct { | |
| unsigned long time_stamp; | |
| u16 length; | |
| u16 next_to_watch; | |
| unsigned int segs; | |
| unsigned int bytecount; | |
| u16 mapped_as_page; | |
| }; | |
| /* Rx */ | |
| struct { | |
| /* arrays of page information for packet split */ | |
| struct e1000_ps_page *ps_pages; | |
| struct page *page; | |
| }; | |
| }; | |
| }; | |
| struct e1000_ring { | |
| struct e1000_adapter *adapter; /* back pointer to adapter */ | |
| void *desc; /* pointer to ring memory */ | |
| dma_addr_t dma; /* phys address of ring */ | |
| unsigned int size; /* length of ring in bytes */ | |
| unsigned int count; /* number of desc. in ring */ | |
| u16 next_to_use; | |
| u16 next_to_clean; | |
| void __iomem *head; | |
| void __iomem *tail; | |
| /* array of buffer information structs */ | |
| struct e1000_buffer *buffer_info; | |
| char name[IFNAMSIZ + 5]; | |
| u32 ims_val; | |
| u32 itr_val; | |
| void __iomem *itr_register; | |
| int set_itr; | |
| struct sk_buff *rx_skb_top; | |
| }; | |
| /* PHY register snapshot values */ | |
| struct e1000_phy_regs { | |
| u16 bmcr; /* basic mode control register */ | |
| u16 bmsr; /* basic mode status register */ | |
| u16 advertise; /* auto-negotiation advertisement */ | |
| u16 lpa; /* link partner ability register */ | |
| u16 expansion; /* auto-negotiation expansion reg */ | |
| u16 ctrl1000; /* 1000BASE-T control register */ | |
| u16 stat1000; /* 1000BASE-T status register */ | |
| u16 estatus; /* extended status register */ | |
| }; | |
| /* board specific private data structure */ | |
| struct e1000_adapter { | |
| struct timer_list watchdog_timer; | |
| struct timer_list phy_info_timer; | |
| struct timer_list blink_timer; | |
| struct work_struct reset_task; | |
| struct work_struct watchdog_task; | |
| const struct e1000_info *ei; | |
| unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)]; | |
| u32 bd_number; | |
| u32 rx_buffer_len; | |
| u16 mng_vlan_id; | |
| u16 link_speed; | |
| u16 link_duplex; | |
| u16 eeprom_vers; | |
| /* track device up/down/testing state */ | |
| unsigned long state; | |
| /* Interrupt Throttle Rate */ | |
| u32 itr; | |
| u32 itr_setting; | |
| u16 tx_itr; | |
| u16 rx_itr; | |
| /* Tx - one ring per active queue */ | |
| struct e1000_ring *tx_ring ____cacheline_aligned_in_smp; | |
| u32 tx_fifo_limit; | |
| struct napi_struct napi; | |
| unsigned int uncorr_errors; /* uncorrectable ECC errors */ | |
| unsigned int corr_errors; /* correctable ECC errors */ | |
| unsigned int restart_queue; | |
| u32 txd_cmd; | |
| bool detect_tx_hung; | |
| bool tx_hang_recheck; | |
| u8 tx_timeout_factor; | |
| u32 tx_int_delay; | |
| u32 tx_abs_int_delay; | |
| unsigned int total_tx_bytes; | |
| unsigned int total_tx_packets; | |
| unsigned int total_rx_bytes; | |
| unsigned int total_rx_packets; | |
| /* Tx stats */ | |
| u64 tpt_old; | |
| u64 colc_old; | |
| u32 gotc; | |
| u64 gotc_old; | |
| u32 tx_timeout_count; | |
| u32 tx_fifo_head; | |
| u32 tx_head_addr; | |
| u32 tx_fifo_size; | |
| u32 tx_dma_failed; | |
| u32 tx_hwtstamp_timeouts; | |
| u32 tx_hwtstamp_skipped; | |
| /* Rx */ | |
| bool (*clean_rx)(struct e1000_ring *ring, int *work_done, | |
| int work_to_do) ____cacheline_aligned_in_smp; | |
| void (*alloc_rx_buf)(struct e1000_ring *ring, int cleaned_count, | |
| gfp_t gfp); | |
| struct e1000_ring *rx_ring; | |
| u32 rx_int_delay; | |
| u32 rx_abs_int_delay; | |
| /* Rx stats */ | |
| u64 hw_csum_err; | |
| u64 hw_csum_good; | |
| u64 rx_hdr_split; | |
| u32 gorc; | |
| u64 gorc_old; | |
| u32 alloc_rx_buff_failed; | |
| u32 rx_dma_failed; | |
| u32 rx_hwtstamp_cleared; | |
| unsigned int rx_ps_pages; | |
| u16 rx_ps_bsize0; | |
| u32 max_frame_size; | |
| u32 min_frame_size; | |
| /* OS defined structs */ | |
| struct net_device *netdev; | |
| struct pci_dev *pdev; | |
| /* structs defined in e1000_hw.h */ | |
| struct e1000_hw hw; | |
| spinlock_t stats64_lock; /* protects statistics counters */ | |
| struct e1000_hw_stats stats; | |
| struct e1000_phy_info phy_info; | |
| struct e1000_phy_stats phy_stats; | |
| /* Snapshot of PHY registers */ | |
| struct e1000_phy_regs phy_regs; | |
| struct e1000_ring test_tx_ring; | |
| struct e1000_ring test_rx_ring; | |
| u32 test_icr; | |
| u32 msg_enable; | |
| unsigned int num_vectors; | |
| struct msix_entry *msix_entries; | |
| int int_mode; | |
| u32 eiac_mask; | |
| u32 eeprom_wol; | |
| u32 wol; | |
| u32 pba; | |
| u32 max_hw_frame_size; | |
| bool fc_autoneg; | |
| unsigned int flags; | |
| unsigned int flags2; | |
| struct work_struct downshift_task; | |
| struct work_struct update_phy_task; | |
| struct work_struct print_hang_task; | |
| int phy_hang_count; | |
| u16 tx_ring_count; | |
| u16 rx_ring_count; | |
| struct kernel_hwtstamp_config hwtstamp_config; | |
| struct delayed_work systim_overflow_work; | |
| struct sk_buff *tx_hwtstamp_skb; | |
| unsigned long tx_hwtstamp_start; | |
| struct work_struct tx_hwtstamp_work; | |
| spinlock_t systim_lock; /* protects SYSTIML/H regsters */ | |
| struct cyclecounter cc; | |
| struct timecounter tc; | |
| struct ptp_clock *ptp_clock; | |
| struct ptp_clock_info ptp_clock_info; | |
| struct pm_qos_request pm_qos_req; | |
| long ptp_delta; | |
| u16 eee_advert; | |
| }; | |
| struct e1000_info { | |
| enum e1000_mac_type mac; | |
| unsigned int flags; | |
| unsigned int flags2; | |
| u32 pba; | |
| u32 max_hw_frame_size; | |
| s32 (*get_variants)(struct e1000_adapter *); | |
| const struct e1000_mac_operations *mac_ops; | |
| const struct e1000_phy_operations *phy_ops; | |
| const struct e1000_nvm_operations *nvm_ops; | |
| }; | |
| s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca); | |
| /* The system time is maintained by a 64-bit counter comprised of the 32-bit | |
| * SYSTIMH and SYSTIML registers. How the counter increments (and therefore | |
| * its resolution) is based on the contents of the TIMINCA register - it | |
| * increments every incperiod (bits 31:24) clock ticks by incvalue (bits 23:0). | |
| * For the best accuracy, the incperiod should be as small as possible. The | |
| * incvalue is scaled by a factor as large as possible (while still fitting | |
| * in bits 23:0) so that relatively small clock corrections can be made. | |
| * | |
| * As a result, a shift of INCVALUE_SHIFT_n is used to fit a value of | |
| * INCVALUE_n into the TIMINCA register allowing 32+8+(24-INCVALUE_SHIFT_n) | |
| * bits to count nanoseconds leaving the rest for fractional nonseconds. | |
| * | |
| * Any given INCVALUE also has an associated maximum adjustment value. This | |
| * maximum adjustment value is the largest increase (or decrease) which can be | |
| * safely applied without overflowing the INCVALUE. Since INCVALUE has | |
| * a maximum range of 24 bits, its largest value is 0xFFFFFF. | |
| * | |
| * To understand where the maximum value comes from, consider the following | |
| * equation: | |
| * | |
| * new_incval = base_incval + (base_incval * adjustment) / 1billion | |
| * | |
| * To avoid overflow that means: | |
| * max_incval = base_incval + (base_incval * max_adj) / billion | |
| * | |
| * Re-arranging: | |
| * max_adj = floor(((max_incval - base_incval) * 1billion) / 1billion) | |
| */ | |
| #define INCVALUE_96MHZ 125 | |
| #define INCVALUE_SHIFT_96MHZ 17 | |
| #define INCPERIOD_SHIFT_96MHZ 2 | |
| #define INCPERIOD_96MHZ (12 >> INCPERIOD_SHIFT_96MHZ) | |
| #define MAX_PPB_96MHZ 23999900 /* 23,999,900 ppb */ | |
| #define INCVALUE_25MHZ 40 | |
| #define INCVALUE_SHIFT_25MHZ 18 | |
| #define INCPERIOD_25MHZ 1 | |
| #define MAX_PPB_25MHZ 599999900 /* 599,999,900 ppb */ | |
| #define INCVALUE_24MHZ 125 | |
| #define INCVALUE_SHIFT_24MHZ 14 | |
| #define INCPERIOD_24MHZ 3 | |
| #define MAX_PPB_24MHZ 999999999 /* 999,999,999 ppb */ | |
| #define INCVALUE_38400KHZ 26 | |
| #define INCVALUE_SHIFT_38400KHZ 19 | |
| #define INCPERIOD_38400KHZ 1 | |
| #define MAX_PPB_38400KHZ 230769100 /* 230,769,100 ppb */ | |
| /* Another drawback of scaling the incvalue by a large factor is the | |
| * 64-bit SYSTIM register overflows more quickly. This is dealt with | |
| * by simply reading the clock before it overflows. | |
| * | |
| * Clock ns bits Overflows after | |
| * ~~~~~~ ~~~~~~~ ~~~~~~~~~~~~~~~ | |
| * 96MHz 47-bit 2^(47-INCPERIOD_SHIFT_96MHz) / 10^9 / 3600 = 9.77 hrs | |
| * 25MHz 46-bit 2^46 / 10^9 / 3600 = 19.55 hours | |
| */ | |
| #define E1000_SYSTIM_OVERFLOW_PERIOD (HZ * 60 * 60 * 4) | |
| #define E1000_MAX_82574_SYSTIM_REREADS 50 | |
| #define E1000_82574_SYSTIM_EPSILON (1ULL << 35ULL) | |
| /* hardware capability, feature, and workaround flags */ | |
| #define FLAG_HAS_AMT BIT(0) | |
| #define FLAG_HAS_FLASH BIT(1) | |
| #define FLAG_HAS_HW_VLAN_FILTER BIT(2) | |
| #define FLAG_HAS_WOL BIT(3) | |
| /* reserved BIT(4) */ | |
| #define FLAG_HAS_CTRLEXT_ON_LOAD BIT(5) | |
| #define FLAG_HAS_SWSM_ON_LOAD BIT(6) | |
| #define FLAG_HAS_JUMBO_FRAMES BIT(7) | |
| #define FLAG_READ_ONLY_NVM BIT(8) | |
| #define FLAG_IS_ICH BIT(9) | |
| #define FLAG_HAS_MSIX BIT(10) | |
| #define FLAG_HAS_SMART_POWER_DOWN BIT(11) | |
| #define FLAG_IS_QUAD_PORT_A BIT(12) | |
| #define FLAG_IS_QUAD_PORT BIT(13) | |
| #define FLAG_HAS_HW_TIMESTAMP BIT(14) | |
| #define FLAG_APME_IN_WUC BIT(15) | |
| #define FLAG_APME_IN_CTRL3 BIT(16) | |
| #define FLAG_APME_CHECK_PORT_B BIT(17) | |
| #define FLAG_DISABLE_FC_PAUSE_TIME BIT(18) | |
| #define FLAG_NO_WAKE_UCAST BIT(19) | |
| #define FLAG_MNG_PT_ENABLED BIT(20) | |
| #define FLAG_RESET_OVERWRITES_LAA BIT(21) | |
| #define FLAG_TARC_SPEED_MODE_BIT BIT(22) | |
| #define FLAG_TARC_SET_BIT_ZERO BIT(23) | |
| #define FLAG_RX_NEEDS_RESTART BIT(24) | |
| #define FLAG_LSC_GIG_SPEED_DROP BIT(25) | |
| #define FLAG_SMART_POWER_DOWN BIT(26) | |
| #define FLAG_MSI_ENABLED BIT(27) | |
| /* reserved BIT(28) */ | |
| #define FLAG_TSO_FORCE BIT(29) | |
| #define FLAG_RESTART_NOW BIT(30) | |
| #define FLAG_MSI_TEST_FAILED BIT(31) | |
| #define FLAG2_CRC_STRIPPING BIT(0) | |
| #define FLAG2_HAS_PHY_WAKEUP BIT(1) | |
| #define FLAG2_IS_DISCARDING BIT(2) | |
| #define FLAG2_DISABLE_ASPM_L1 BIT(3) | |
| #define FLAG2_HAS_PHY_STATS BIT(4) | |
| #define FLAG2_HAS_EEE BIT(5) | |
| #define FLAG2_DMA_BURST BIT(6) | |
| #define FLAG2_DISABLE_ASPM_L0S BIT(7) | |
| #define FLAG2_DISABLE_AIM BIT(8) | |
| #define FLAG2_CHECK_PHY_HANG BIT(9) | |
| #define FLAG2_NO_DISABLE_RX BIT(10) | |
| #define FLAG2_PCIM2PCI_ARBITER_WA BIT(11) | |
| #define FLAG2_DFLT_CRC_STRIPPING BIT(12) | |
| #define FLAG2_CHECK_RX_HWTSTAMP BIT(13) | |
| #define FLAG2_CHECK_SYSTIM_OVERFLOW BIT(14) | |
| #define FLAG2_ENABLE_S0IX_FLOWS BIT(15) | |
| #define FLAG2_DISABLE_K1 BIT(16) | |
| #define E1000_RX_DESC_PS(R, i) \ | |
| (&(((union e1000_rx_desc_packet_split *)((R).desc))[i])) | |
| #define E1000_RX_DESC_EXT(R, i) \ | |
| (&(((union e1000_rx_desc_extended *)((R).desc))[i])) | |
| #define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i])) | |
| #define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc) | |
| #define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc) | |
| enum e1000_state_t { | |
| __E1000_TESTING, | |
| __E1000_RESETTING, | |
| __E1000_ACCESS_SHARED_RESOURCE, | |
| __E1000_DOWN | |
| }; | |
| enum latency_range { | |
| lowest_latency = 0, | |
| low_latency = 1, | |
| bulk_latency = 2, | |
| latency_invalid = 255 | |
| }; | |
| extern char e1000e_driver_name[]; | |
| void e1000e_check_options(struct e1000_adapter *adapter); | |
| void e1000e_set_ethtool_ops(struct net_device *netdev); | |
| int e1000e_open(struct net_device *netdev); | |
| int e1000e_close(struct net_device *netdev); | |
| void e1000e_up(struct e1000_adapter *adapter); | |
| void e1000e_down(struct e1000_adapter *adapter, bool reset); | |
| void e1000e_reinit_locked(struct e1000_adapter *adapter); | |
| void e1000e_reset(struct e1000_adapter *adapter); | |
| void e1000e_power_up_phy(struct e1000_adapter *adapter); | |
| int e1000e_setup_rx_resources(struct e1000_ring *ring); | |
| int e1000e_setup_tx_resources(struct e1000_ring *ring); | |
| void e1000e_free_rx_resources(struct e1000_ring *ring); | |
| void e1000e_free_tx_resources(struct e1000_ring *ring); | |
| void e1000e_get_stats64(struct net_device *netdev, | |
| struct rtnl_link_stats64 *stats); | |
| void e1000e_set_interrupt_capability(struct e1000_adapter *adapter); | |
| void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter); | |
| void e1000e_get_hw_control(struct e1000_adapter *adapter); | |
| void e1000e_release_hw_control(struct e1000_adapter *adapter); | |
| void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr); | |
| extern unsigned int copybreak; | |
| extern const struct e1000_info e1000_82571_info; | |
| extern const struct e1000_info e1000_82572_info; | |
| extern const struct e1000_info e1000_82573_info; | |
| extern const struct e1000_info e1000_82574_info; | |
| extern const struct e1000_info e1000_82583_info; | |
| extern const struct e1000_info e1000_ich8_info; | |
| extern const struct e1000_info e1000_ich9_info; | |
| extern const struct e1000_info e1000_ich10_info; | |
| extern const struct e1000_info e1000_pch_info; | |
| extern const struct e1000_info e1000_pch2_info; | |
| extern const struct e1000_info e1000_pch_lpt_info; | |
| extern const struct e1000_info e1000_pch_spt_info; | |
| extern const struct e1000_info e1000_pch_cnp_info; | |
| extern const struct e1000_info e1000_pch_tgp_info; | |
| extern const struct e1000_info e1000_pch_adp_info; | |
| extern const struct e1000_info e1000_pch_mtp_info; | |
| extern const struct e1000_info e1000_pch_ptp_info; | |
| extern const struct e1000_info e1000_es2_info; | |
| void e1000e_ptp_init(struct e1000_adapter *adapter); | |
| void e1000e_ptp_remove(struct e1000_adapter *adapter); | |
| u64 e1000e_read_systim(struct e1000_adapter *adapter, | |
| struct ptp_system_timestamp *sts); | |
| static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw) | |
| { | |
| return hw->phy.ops.reset(hw); | |
| } | |
| static inline s32 e1e_rphy(struct e1000_hw *hw, u32 offset, u16 *data) | |
| { | |
| return hw->phy.ops.read_reg(hw, offset, data); | |
| } | |
| static inline s32 e1e_rphy_locked(struct e1000_hw *hw, u32 offset, u16 *data) | |
| { | |
| return hw->phy.ops.read_reg_locked(hw, offset, data); | |
| } | |
| static inline s32 e1e_wphy(struct e1000_hw *hw, u32 offset, u16 data) | |
| { | |
| return hw->phy.ops.write_reg(hw, offset, data); | |
| } | |
| static inline s32 e1e_wphy_locked(struct e1000_hw *hw, u32 offset, u16 data) | |
| { | |
| return hw->phy.ops.write_reg_locked(hw, offset, data); | |
| } | |
| void e1000e_reload_nvm_generic(struct e1000_hw *hw); | |
| static inline s32 e1000e_read_mac_addr(struct e1000_hw *hw) | |
| { | |
| if (hw->mac.ops.read_mac_addr) | |
| return hw->mac.ops.read_mac_addr(hw); | |
| return e1000_read_mac_addr_generic(hw); | |
| } | |
| static inline s32 e1000_validate_nvm_checksum(struct e1000_hw *hw) | |
| { | |
| return hw->nvm.ops.validate(hw); | |
| } | |
| static inline s32 e1000e_update_nvm_checksum(struct e1000_hw *hw) | |
| { | |
| return hw->nvm.ops.update(hw); | |
| } | |
| static inline s32 e1000_read_nvm(struct e1000_hw *hw, u16 offset, u16 words, | |
| u16 *data) | |
| { | |
| return hw->nvm.ops.read(hw, offset, words, data); | |
| } | |
| static inline s32 e1000_write_nvm(struct e1000_hw *hw, u16 offset, u16 words, | |
| u16 *data) | |
| { | |
| return hw->nvm.ops.write(hw, offset, words, data); | |
| } | |
| static inline s32 e1000_get_phy_info(struct e1000_hw *hw) | |
| { | |
| return hw->phy.ops.get_info(hw); | |
| } | |
| static inline u32 __er32(struct e1000_hw *hw, unsigned long reg) | |
| { | |
| return readl(hw->hw_addr + reg); | |
| } | |
| #define er32(reg) __er32(hw, E1000_##reg) | |
| void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val); | |
| #define ew32(reg, val) __ew32(hw, E1000_##reg, (val)) | |
| #define e1e_flush() er32(STATUS) | |
| #define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \ | |
| (__ew32((a), (reg + ((offset) << 2)), (value))) | |
| #define E1000_READ_REG_ARRAY(a, reg, offset) \ | |
| (readl((a)->hw_addr + reg + ((offset) << 2))) | |
| #endif /* _E1000_H_ */ |