| // SPDX-License-Identifier: GPL-2.0-or-later | |
| /* | |
| * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" | |
| * | |
| * Copyright (c) 2006 Olivier DANET <odanet@caramail.com> | |
| */ | |
| /* In that file, frequencies are expressed in kiloHertz to avoid 32 bits overflows */ | |
| #include <linux/module.h> | |
| #include <linux/delay.h> | |
| #include <linux/dvb/frontend.h> | |
| #include <linux/i2c.h> | |
| #include <linux/slab.h> | |
| #include <media/dvb_frontend.h> | |
| #include "mt2060.h" | |
| #include "mt2060_priv.h" | |
| static int debug; | |
| module_param(debug, int, 0644); | |
| MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off)."); | |
| #define dprintk(args...) do { if (debug) {printk(KERN_DEBUG "MT2060: " args); printk("\n"); }} while (0) | |
| // Reads a single register | |
| static int mt2060_readreg(struct mt2060_priv *priv, u8 reg, u8 *val) | |
| { | |
| struct i2c_msg msg[2] = { | |
| { .addr = priv->cfg->i2c_address, .flags = 0, .len = 1 }, | |
| { .addr = priv->cfg->i2c_address, .flags = I2C_M_RD, .len = 1 }, | |
| }; | |
| int rc = 0; | |
| u8 *b; | |
| b = kmalloc(2, GFP_KERNEL); | |
| if (!b) | |
| return -ENOMEM; | |
| b[0] = reg; | |
| b[1] = 0; | |
| msg[0].buf = b; | |
| msg[1].buf = b + 1; | |
| if (i2c_transfer(priv->i2c, msg, 2) != 2) { | |
| printk(KERN_WARNING "mt2060 I2C read failed\n"); | |
| rc = -EREMOTEIO; | |
| } | |
| *val = b[1]; | |
| kfree(b); | |
| return rc; | |
| } | |
| // Writes a single register | |
| static int mt2060_writereg(struct mt2060_priv *priv, u8 reg, u8 val) | |
| { | |
| struct i2c_msg msg = { | |
| .addr = priv->cfg->i2c_address, .flags = 0, .len = 2 | |
| }; | |
| u8 *buf; | |
| int rc = 0; | |
| buf = kmalloc(2, GFP_KERNEL); | |
| if (!buf) | |
| return -ENOMEM; | |
| buf[0] = reg; | |
| buf[1] = val; | |
| msg.buf = buf; | |
| if (i2c_transfer(priv->i2c, &msg, 1) != 1) { | |
| printk(KERN_WARNING "mt2060 I2C write failed\n"); | |
| rc = -EREMOTEIO; | |
| } | |
| kfree(buf); | |
| return rc; | |
| } | |
| // Writes a set of consecutive registers | |
| static int mt2060_writeregs(struct mt2060_priv *priv,u8 *buf, u8 len) | |
| { | |
| int rem, val_len; | |
| u8 *xfer_buf; | |
| int rc = 0; | |
| struct i2c_msg msg = { | |
| .addr = priv->cfg->i2c_address, .flags = 0 | |
| }; | |
| xfer_buf = kmalloc(16, GFP_KERNEL); | |
| if (!xfer_buf) | |
| return -ENOMEM; | |
| msg.buf = xfer_buf; | |
| for (rem = len - 1; rem > 0; rem -= priv->i2c_max_regs) { | |
| val_len = min_t(int, rem, priv->i2c_max_regs); | |
| msg.len = 1 + val_len; | |
| xfer_buf[0] = buf[0] + len - 1 - rem; | |
| memcpy(&xfer_buf[1], &buf[1 + len - 1 - rem], val_len); | |
| if (i2c_transfer(priv->i2c, &msg, 1) != 1) { | |
| printk(KERN_WARNING "mt2060 I2C write failed (len=%i)\n", val_len); | |
| rc = -EREMOTEIO; | |
| break; | |
| } | |
| } | |
| kfree(xfer_buf); | |
| return rc; | |
| } | |
| // Initialisation sequences | |
| // LNABAND=3, NUM1=0x3C, DIV1=0x74, NUM2=0x1080, DIV2=0x49 | |
| static u8 mt2060_config1[] = { | |
| REG_LO1C1, | |
| 0x3F, 0x74, 0x00, 0x08, 0x93 | |
| }; | |
| // FMCG=2, GP2=0, GP1=0 | |
| static u8 mt2060_config2[] = { | |
| REG_MISC_CTRL, | |
| 0x20, 0x1E, 0x30, 0xff, 0x80, 0xff, 0x00, 0x2c, 0x42 | |
| }; | |
| // VGAG=3, V1CSE=1 | |
| #ifdef MT2060_SPURCHECK | |
| /* The function below calculates the frequency offset between the output frequency if2 | |
| and the closer cross modulation subcarrier between lo1 and lo2 up to the tenth harmonic */ | |
| static int mt2060_spurcalc(u32 lo1,u32 lo2,u32 if2) | |
| { | |
| int I,J; | |
| int dia,diamin,diff; | |
| diamin=1000000; | |
| for (I = 1; I < 10; I++) { | |
| J = ((2*I*lo1)/lo2+1)/2; | |
| diff = I*(int)lo1-J*(int)lo2; | |
| if (diff < 0) diff=-diff; | |
| dia = (diff-(int)if2); | |
| if (dia < 0) dia=-dia; | |
| if (diamin > dia) diamin=dia; | |
| } | |
| return diamin; | |
| } | |
| #define BANDWIDTH 4000 // kHz | |
| /* Calculates the frequency offset to add to avoid spurs. Returns 0 if no offset is needed */ | |
| static int mt2060_spurcheck(u32 lo1,u32 lo2,u32 if2) | |
| { | |
| u32 Spur,Sp1,Sp2; | |
| int I,J; | |
| I=0; | |
| J=1000; | |
| Spur=mt2060_spurcalc(lo1,lo2,if2); | |
| if (Spur < BANDWIDTH) { | |
| /* Potential spurs detected */ | |
| dprintk("Spurs before : f_lo1: %d f_lo2: %d (kHz)", | |
| (int)lo1,(int)lo2); | |
| I=1000; | |
| Sp1 = mt2060_spurcalc(lo1+I,lo2+I,if2); | |
| Sp2 = mt2060_spurcalc(lo1-I,lo2-I,if2); | |
| if (Sp1 < Sp2) { | |
| J=-J; I=-I; Spur=Sp2; | |
| } else | |
| Spur=Sp1; | |
| while (Spur < BANDWIDTH) { | |
| I += J; | |
| Spur = mt2060_spurcalc(lo1+I,lo2+I,if2); | |
| } | |
| dprintk("Spurs after : f_lo1: %d f_lo2: %d (kHz)", | |
| (int)(lo1+I),(int)(lo2+I)); | |
| } | |
| return I; | |
| } | |
| #endif | |
| #define IF2 36150 // IF2 frequency = 36.150 MHz | |
| #define FREF 16000 // Quartz oscillator 16 MHz | |
| static int mt2060_set_params(struct dvb_frontend *fe) | |
| { | |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; | |
| struct mt2060_priv *priv; | |
| int i=0; | |
| u32 freq; | |
| u8 lnaband; | |
| u32 f_lo1,f_lo2; | |
| u32 div1,num1,div2,num2; | |
| u8 b[8]; | |
| u32 if1; | |
| priv = fe->tuner_priv; | |
| if1 = priv->if1_freq; | |
| b[0] = REG_LO1B1; | |
| b[1] = 0xFF; | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */ | |
| mt2060_writeregs(priv,b,2); | |
| freq = c->frequency / 1000; /* Hz -> kHz */ | |
| f_lo1 = freq + if1 * 1000; | |
| f_lo1 = (f_lo1 / 250) * 250; | |
| f_lo2 = f_lo1 - freq - IF2; | |
| // From the Comtech datasheet, the step used is 50kHz. The tuner chip could be more precise | |
| f_lo2 = ((f_lo2 + 25) / 50) * 50; | |
| priv->frequency = (f_lo1 - f_lo2 - IF2) * 1000; | |
| #ifdef MT2060_SPURCHECK | |
| // LO-related spurs detection and correction | |
| num1 = mt2060_spurcheck(f_lo1,f_lo2,IF2); | |
| f_lo1 += num1; | |
| f_lo2 += num1; | |
| #endif | |
| //Frequency LO1 = 16MHz * (DIV1 + NUM1/64 ) | |
| num1 = f_lo1 / (FREF / 64); | |
| div1 = num1 / 64; | |
| num1 &= 0x3f; | |
| // Frequency LO2 = 16MHz * (DIV2 + NUM2/8192 ) | |
| num2 = f_lo2 * 64 / (FREF / 128); | |
| div2 = num2 / 8192; | |
| num2 &= 0x1fff; | |
| if (freq <= 95000) lnaband = 0xB0; else | |
| if (freq <= 180000) lnaband = 0xA0; else | |
| if (freq <= 260000) lnaband = 0x90; else | |
| if (freq <= 335000) lnaband = 0x80; else | |
| if (freq <= 425000) lnaband = 0x70; else | |
| if (freq <= 480000) lnaband = 0x60; else | |
| if (freq <= 570000) lnaband = 0x50; else | |
| if (freq <= 645000) lnaband = 0x40; else | |
| if (freq <= 730000) lnaband = 0x30; else | |
| if (freq <= 810000) lnaband = 0x20; else lnaband = 0x10; | |
| b[0] = REG_LO1C1; | |
| b[1] = lnaband | ((num1 >>2) & 0x0F); | |
| b[2] = div1; | |
| b[3] = (num2 & 0x0F) | ((num1 & 3) << 4); | |
| b[4] = num2 >> 4; | |
| b[5] = ((num2 >>12) & 1) | (div2 << 1); | |
| dprintk("IF1: %dMHz",(int)if1); | |
| dprintk("PLL freq=%dkHz f_lo1=%dkHz f_lo2=%dkHz",(int)freq,(int)f_lo1,(int)f_lo2); | |
| dprintk("PLL div1=%d num1=%d div2=%d num2=%d",(int)div1,(int)num1,(int)div2,(int)num2); | |
| dprintk("PLL [1..5]: %2x %2x %2x %2x %2x",(int)b[1],(int)b[2],(int)b[3],(int)b[4],(int)b[5]); | |
| mt2060_writeregs(priv,b,6); | |
| //Waits for pll lock or timeout | |
| i = 0; | |
| do { | |
| mt2060_readreg(priv,REG_LO_STATUS,b); | |
| if ((b[0] & 0x88)==0x88) | |
| break; | |
| msleep(4); | |
| i++; | |
| } while (i<10); | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */ | |
| return 0; | |
| } | |
| static void mt2060_calibrate(struct mt2060_priv *priv) | |
| { | |
| u8 b = 0; | |
| int i = 0; | |
| if (mt2060_writeregs(priv,mt2060_config1,sizeof(mt2060_config1))) | |
| return; | |
| if (mt2060_writeregs(priv,mt2060_config2,sizeof(mt2060_config2))) | |
| return; | |
| /* initialize the clock output */ | |
| mt2060_writereg(priv, REG_VGAG, (priv->cfg->clock_out << 6) | 0x30); | |
| do { | |
| b |= (1 << 6); // FM1SS; | |
| mt2060_writereg(priv, REG_LO2C1,b); | |
| msleep(20); | |
| if (i == 0) { | |
| b |= (1 << 7); // FM1CA; | |
| mt2060_writereg(priv, REG_LO2C1,b); | |
| b &= ~(1 << 7); // FM1CA; | |
| msleep(20); | |
| } | |
| b &= ~(1 << 6); // FM1SS | |
| mt2060_writereg(priv, REG_LO2C1,b); | |
| msleep(20); | |
| i++; | |
| } while (i < 9); | |
| i = 0; | |
| while (i++ < 10 && mt2060_readreg(priv, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0) | |
| msleep(20); | |
| if (i <= 10) { | |
| mt2060_readreg(priv, REG_FM_FREQ, &priv->fmfreq); // now find out, what is fmreq used for :) | |
| dprintk("calibration was successful: %d", (int)priv->fmfreq); | |
| } else | |
| dprintk("FMCAL timed out"); | |
| } | |
| static int mt2060_get_frequency(struct dvb_frontend *fe, u32 *frequency) | |
| { | |
| struct mt2060_priv *priv = fe->tuner_priv; | |
| *frequency = priv->frequency; | |
| return 0; | |
| } | |
| static int mt2060_get_if_frequency(struct dvb_frontend *fe, u32 *frequency) | |
| { | |
| *frequency = IF2 * 1000; | |
| return 0; | |
| } | |
| static int mt2060_init(struct dvb_frontend *fe) | |
| { | |
| struct mt2060_priv *priv = fe->tuner_priv; | |
| int ret; | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */ | |
| if (priv->sleep) { | |
| ret = mt2060_writereg(priv, REG_MISC_CTRL, 0x20); | |
| if (ret) | |
| goto err_i2c_gate_ctrl; | |
| } | |
| ret = mt2060_writereg(priv, REG_VGAG, | |
| (priv->cfg->clock_out << 6) | 0x33); | |
| err_i2c_gate_ctrl: | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */ | |
| return ret; | |
| } | |
| static int mt2060_sleep(struct dvb_frontend *fe) | |
| { | |
| struct mt2060_priv *priv = fe->tuner_priv; | |
| int ret; | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */ | |
| ret = mt2060_writereg(priv, REG_VGAG, | |
| (priv->cfg->clock_out << 6) | 0x30); | |
| if (ret) | |
| goto err_i2c_gate_ctrl; | |
| if (priv->sleep) | |
| ret = mt2060_writereg(priv, REG_MISC_CTRL, 0xe8); | |
| err_i2c_gate_ctrl: | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */ | |
| return ret; | |
| } | |
| static void mt2060_release(struct dvb_frontend *fe) | |
| { | |
| kfree(fe->tuner_priv); | |
| fe->tuner_priv = NULL; | |
| } | |
| static const struct dvb_tuner_ops mt2060_tuner_ops = { | |
| .info = { | |
| .name = "Microtune MT2060", | |
| .frequency_min_hz = 48 * MHz, | |
| .frequency_max_hz = 860 * MHz, | |
| .frequency_step_hz = 50 * kHz, | |
| }, | |
| .release = mt2060_release, | |
| .init = mt2060_init, | |
| .sleep = mt2060_sleep, | |
| .set_params = mt2060_set_params, | |
| .get_frequency = mt2060_get_frequency, | |
| .get_if_frequency = mt2060_get_if_frequency, | |
| }; | |
| /* This functions tries to identify a MT2060 tuner by reading the PART/REV register. This is hasty. */ | |
| struct dvb_frontend * mt2060_attach(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct mt2060_config *cfg, u16 if1) | |
| { | |
| struct mt2060_priv *priv = NULL; | |
| u8 id = 0; | |
| priv = kzalloc_obj(struct mt2060_priv); | |
| if (priv == NULL) | |
| return NULL; | |
| priv->cfg = cfg; | |
| priv->i2c = i2c; | |
| priv->if1_freq = if1; | |
| priv->i2c_max_regs = ~0; | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 1); /* open i2c_gate */ | |
| if (mt2060_readreg(priv,REG_PART_REV,&id) != 0) { | |
| kfree(priv); | |
| return NULL; | |
| } | |
| if (id != PART_REV) { | |
| kfree(priv); | |
| return NULL; | |
| } | |
| printk(KERN_INFO "MT2060: successfully identified (IF1 = %d)\n", if1); | |
| memcpy(&fe->ops.tuner_ops, &mt2060_tuner_ops, sizeof(struct dvb_tuner_ops)); | |
| fe->tuner_priv = priv; | |
| mt2060_calibrate(priv); | |
| if (fe->ops.i2c_gate_ctrl) | |
| fe->ops.i2c_gate_ctrl(fe, 0); /* close i2c_gate */ | |
| return fe; | |
| } | |
| EXPORT_SYMBOL_GPL(mt2060_attach); | |
| static int mt2060_probe(struct i2c_client *client) | |
| { | |
| struct mt2060_platform_data *pdata = client->dev.platform_data; | |
| struct dvb_frontend *fe; | |
| struct mt2060_priv *dev; | |
| int ret; | |
| u8 chip_id; | |
| dev_dbg(&client->dev, "\n"); | |
| if (!pdata) { | |
| dev_err(&client->dev, "Cannot proceed without platform data\n"); | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL); | |
| if (!dev) { | |
| ret = -ENOMEM; | |
| goto err; | |
| } | |
| fe = pdata->dvb_frontend; | |
| dev->config.i2c_address = client->addr; | |
| dev->config.clock_out = pdata->clock_out; | |
| dev->cfg = &dev->config; | |
| dev->i2c = client->adapter; | |
| dev->if1_freq = pdata->if1 ? pdata->if1 : 1220; | |
| dev->client = client; | |
| dev->i2c_max_regs = pdata->i2c_write_max ? pdata->i2c_write_max - 1 : ~0; | |
| dev->sleep = true; | |
| ret = mt2060_readreg(dev, REG_PART_REV, &chip_id); | |
| if (ret) { | |
| ret = -ENODEV; | |
| goto err; | |
| } | |
| dev_dbg(&client->dev, "chip id=%02x\n", chip_id); | |
| if (chip_id != PART_REV) { | |
| ret = -ENODEV; | |
| goto err; | |
| } | |
| /* Power on, calibrate, sleep */ | |
| ret = mt2060_writereg(dev, REG_MISC_CTRL, 0x20); | |
| if (ret) | |
| goto err; | |
| mt2060_calibrate(dev); | |
| ret = mt2060_writereg(dev, REG_MISC_CTRL, 0xe8); | |
| if (ret) | |
| goto err; | |
| dev_info(&client->dev, "Microtune MT2060 successfully identified\n"); | |
| memcpy(&fe->ops.tuner_ops, &mt2060_tuner_ops, sizeof(fe->ops.tuner_ops)); | |
| fe->ops.tuner_ops.release = NULL; | |
| fe->tuner_priv = dev; | |
| i2c_set_clientdata(client, dev); | |
| return 0; | |
| err: | |
| dev_dbg(&client->dev, "failed=%d\n", ret); | |
| return ret; | |
| } | |
| static void mt2060_remove(struct i2c_client *client) | |
| { | |
| dev_dbg(&client->dev, "\n"); | |
| } | |
| static const struct i2c_device_id mt2060_id_table[] = { | |
| { .name = "mt2060" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, mt2060_id_table); | |
| static struct i2c_driver mt2060_driver = { | |
| .driver = { | |
| .name = "mt2060", | |
| .suppress_bind_attrs = true, | |
| }, | |
| .probe = mt2060_probe, | |
| .remove = mt2060_remove, | |
| .id_table = mt2060_id_table, | |
| }; | |
| module_i2c_driver(mt2060_driver); | |
| MODULE_AUTHOR("Olivier DANET"); | |
| MODULE_DESCRIPTION("Microtune MT2060 silicon tuner driver"); | |
| MODULE_LICENSE("GPL"); |