| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * ov2732 driver | |
| * | |
| * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd. | |
| * Copyright (C) 2025-2026 Walter Werner Schneider <contact@schnwalter.eu> | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/i2c.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <media/v4l2-cci.h> | |
| #include <media/v4l2-common.h> | |
| #include <media/v4l2-ctrls.h> | |
| #include <media/v4l2-device.h> | |
| #include <media/v4l2-fwnode.h> | |
| #define OV2732_LANES 2 | |
| #define OV2732_BITS_PER_SAMPLE 10 | |
| #define OV2732_LINK_FREQ_DEFAULT 360000000 | |
| #define OV2732_XVCLK_FREQ 24000000 | |
| #define OV2732_PIXEL_RATE \ | |
| (OV2732_LINK_FREQ_DEFAULT * 2 * OV2732_LANES / OV2732_BITS_PER_SAMPLE) | |
| #define OV2732_NATIVE_WIDTH 1920U | |
| #define OV2732_NATIVE_HEIGHT 1080U | |
| /* Delay from power up to the first SCCB transaction. */ | |
| #define OV2732_POWER_UP_DELAY_CYCLES 8192 | |
| /* Delay from the last SCCB transaction to power down. */ | |
| #define OV2732_POWER_DOWN_DELAY_CYCLES 512 | |
| #define OV2732_DELAY_US(cycles) \ | |
| (DIV_ROUND_UP((cycles), OV2732_XVCLK_FREQ / USEC_PER_SEC)) | |
| #define OV2732_REG_CHIP_ID CCI_REG24(0x300a) | |
| #define OV2732_CHIP_ID 0x002732 | |
| #define OV2732_REG_MODE_SELECT CCI_REG8(0x0100) | |
| #define OV2732_MODE_STANDBY 0x00 | |
| #define OV2732_MODE_STREAMING 0x01 | |
| #define OV2732_REG_ANALOGUE_GAIN CCI_REG16(0x3508) | |
| #define OV2732_REG_DIGITAL_GAIN CCI_REG16(0x350a) | |
| #define OV2732_REG_EXPOSURE CCI_REG24(0x3500) | |
| #define OV2732_REG_HTS CCI_REG16(0x380c) | |
| #define OV2732_REG_VTS CCI_REG16(0x380e) | |
| #define OV2732_ANALOGUE_GAIN_MIN 0x80 | |
| /* Max analogue gain is documented as 0x3fff, but it overflows after 0x3ff. */ | |
| #define OV2732_ANALOGUE_GAIN_MAX 0x3ff | |
| #define OV2732_ANALOGUE_GAIN_DEFAULT 0x80 | |
| #define OV2732_DIGITAL_GAIN_MIN 0x00 | |
| #define OV2732_DIGITAL_GAIN_MAX 0x3fff | |
| #define OV2732_DIGITAL_GAIN_DEFAULT 0x0400 | |
| #define OV2732_EXPOSURE_DEFAULT 0x40 | |
| #define OV2732_EXPOSURE_MIN 0x10 | |
| #define OV2732_EXPOSURE_OFFSET 4 | |
| #define OV2732_HBLANK_DEFAULT 0x0068 | |
| #define OV2732_VTS_MAX 0x7fff | |
| #define OV2732_REG_TEST_PATTERN CCI_REG8(0x5080) | |
| #define OV2732_TEST_PATTERN_DISABLE 0x00 | |
| #define OV2732_TEST_PATTERN_BAR1 0x80 | |
| #define OV2732_TEST_PATTERN_BAR2 0x84 | |
| #define OV2732_TEST_PATTERN_BAR3 0x88 | |
| #define OV2732_TEST_PATTERN_BAR4 0x8c | |
| #define OV2732_TEST_PATTERN_BAR5 0xC0 | |
| #define OV2732_TEST_PATTERN_RANDOM 0x81 | |
| #define OV2732_TEST_PATTERN_SQUARES_C 0x82 | |
| #define OV2732_TEST_PATTERN_SQUARES_BW 0x92 | |
| static const char * const ov2732_supply_names[] = { | |
| "avdd", /* Analog power */ | |
| "dovdd", /* Digital I/O power */ | |
| "dvdd", /* Digital core power */ | |
| }; | |
| static const struct cci_reg_sequence ov2732_common_regs[] = { | |
| /* PLL control, reset all registers. */ | |
| { CCI_REG8(0x0103), 0x01 }, | |
| /* Analog control. */ | |
| { CCI_REG8(0x3600), 0x55 }, | |
| { CCI_REG8(0x3601), 0x52 }, | |
| { CCI_REG8(0x3612), 0xb5 }, | |
| { CCI_REG8(0x3613), 0xb3 }, | |
| { CCI_REG8(0x3616), 0x83 }, | |
| { CCI_REG8(0x3621), 0x00 }, | |
| { CCI_REG8(0x3624), 0x06 }, | |
| { CCI_REG8(0x3642), 0x88 }, | |
| { CCI_REG8(0x3660), 0x00 }, | |
| { CCI_REG8(0x3661), 0x00 }, | |
| { CCI_REG8(0x366a), 0x64 }, | |
| { CCI_REG8(0x366c), 0x00 }, | |
| { CCI_REG8(0x366e), 0xff }, | |
| { CCI_REG8(0x366f), 0xff }, | |
| { CCI_REG8(0x3677), 0x11 }, | |
| { CCI_REG8(0x3678), 0x11 }, | |
| { CCI_REG8(0x3679), 0x0c }, | |
| { CCI_REG8(0x3680), 0xff }, | |
| { CCI_REG8(0x3681), 0x16 }, | |
| { CCI_REG8(0x3682), 0x16 }, | |
| { CCI_REG8(0x3683), 0x90 }, | |
| { CCI_REG8(0x3684), 0x90 }, | |
| /* ADC sync control. */ | |
| { CCI_REG8(0x4503), 0x00 }, | |
| { CCI_REG8(0x4508), 0x14 }, | |
| { CCI_REG8(0x450a), 0x00 }, | |
| { CCI_REG8(0x450b), 0x40 }, | |
| /* ISP control, enable: WIN, DPC & ISP. */ | |
| { CCI_REG8(0x5000), 0xa1 }, | |
| }; | |
| struct ov2732_mode { | |
| u32 width; | |
| u32 height; | |
| u32 vts; | |
| }; | |
| static const struct ov2732_mode supported_modes[] = { | |
| { | |
| .width = 1920, | |
| .height = 1080, | |
| .vts = 1184, | |
| }, | |
| }; | |
| struct ov2732 { | |
| struct device *dev; | |
| struct regmap *regmap; | |
| struct media_pad pad; | |
| struct v4l2_subdev sd; | |
| struct v4l2_ctrl_handler ctrl_handler; | |
| struct v4l2_ctrl *hblank; | |
| struct v4l2_ctrl *vblank; | |
| struct v4l2_ctrl *exposure; | |
| struct clk *xvclk; | |
| u32 xvclk_freq; | |
| struct gpio_desc *powerdown_gpio; | |
| struct gpio_desc *reset_gpio; | |
| struct regulator_bulk_data supplies[ARRAY_SIZE(ov2732_supply_names)]; | |
| }; | |
| #define to_ov2732(_sd) container_of(_sd, struct ov2732, sd) | |
| static const s64 link_freq_menu_items[] = { | |
| OV2732_LINK_FREQ_DEFAULT, | |
| }; | |
| static const char * const ov2732_test_pattern_menu[] = { | |
| "Disabled", | |
| "Vertical Color Bar Type 1", | |
| "Vertical Color Bar Type 2", | |
| "Vertical Color Bar Type 3", | |
| "Vertical Color Bar Type 4", | |
| "Vertical Color Bar Type 5", | |
| "Random", | |
| "Color Squares", | |
| "Black and White Squares", | |
| }; | |
| static const int ov2732_test_pattern_val[] = { | |
| OV2732_TEST_PATTERN_DISABLE, | |
| OV2732_TEST_PATTERN_BAR1, | |
| OV2732_TEST_PATTERN_BAR2, | |
| OV2732_TEST_PATTERN_BAR3, | |
| OV2732_TEST_PATTERN_BAR4, | |
| OV2732_TEST_PATTERN_BAR5, | |
| OV2732_TEST_PATTERN_RANDOM, | |
| OV2732_TEST_PATTERN_SQUARES_C, | |
| OV2732_TEST_PATTERN_SQUARES_BW, | |
| }; | |
| static int ov2732_power_on(struct device *dev) | |
| { | |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| int ret; | |
| ret = regulator_bulk_enable(ARRAY_SIZE(ov2732_supply_names), | |
| ov2732->supplies); | |
| if (ret) { | |
| dev_err(dev, "failed to enable regulators\n"); | |
| return ret; | |
| } | |
| ret = clk_prepare_enable(ov2732->xvclk); | |
| if (ret) { | |
| dev_err(dev, "failed to enable clock\n"); | |
| goto reg_off; | |
| } | |
| /* Wait 10ms before power up, as per datasheet. */ | |
| fsleep(10 * USEC_PER_MSEC); | |
| gpiod_set_value_cansleep(ov2732->reset_gpio, 0); | |
| gpiod_set_value_cansleep(ov2732->powerdown_gpio, 0); | |
| /* Datasheet requires an 8192 cycles wait, but that isn't enough. */ | |
| fsleep(OV2732_DELAY_US(OV2732_POWER_UP_DELAY_CYCLES * 2)); | |
| return 0; | |
| reg_off: | |
| regulator_bulk_disable(ARRAY_SIZE(ov2732_supply_names), | |
| ov2732->supplies); | |
| return ret; | |
| } | |
| static int ov2732_power_off(struct device *dev) | |
| { | |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| clk_disable_unprepare(ov2732->xvclk); | |
| /* Wait for 512 cycles as per datasheet. */ | |
| fsleep(OV2732_DELAY_US(OV2732_POWER_DOWN_DELAY_CYCLES)); | |
| gpiod_set_value_cansleep(ov2732->powerdown_gpio, 1); | |
| gpiod_set_value_cansleep(ov2732->reset_gpio, 1); | |
| regulator_bulk_disable(ARRAY_SIZE(ov2732_supply_names), | |
| ov2732->supplies); | |
| return 0; | |
| } | |
| static int ov2732_identify_chip(struct ov2732 *ov2732) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&ov2732->sd); | |
| int ret; | |
| u64 val; | |
| ret = cci_read(ov2732->regmap, OV2732_REG_CHIP_ID, &val, NULL); | |
| if (ret) | |
| return dev_err_probe(&client->dev, ret, | |
| "failed to read chip id\n"); | |
| if (val != OV2732_CHIP_ID) | |
| return dev_err_probe(&client->dev, -ENODEV, | |
| "chip id mismatch: %x!=%llx\n", | |
| OV2732_CHIP_ID, val); | |
| return 0; | |
| } | |
| static int ov2732_enum_mbus_code(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, | |
| struct v4l2_subdev_mbus_code_enum *code) | |
| { | |
| if (code->index != 0) | |
| return -EINVAL; | |
| code->code = MEDIA_BUS_FMT_SBGGR10_1X10; | |
| return 0; | |
| } | |
| static int ov2732_enum_frame_size(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, | |
| struct v4l2_subdev_frame_size_enum *fse) | |
| { | |
| if (fse->index >= ARRAY_SIZE(supported_modes)) | |
| return -EINVAL; | |
| fse->min_width = supported_modes[fse->index].width; | |
| fse->max_width = fse->min_width; | |
| fse->min_height = supported_modes[fse->index].height; | |
| fse->max_height = fse->min_height; | |
| return 0; | |
| } | |
| static int ov2732_set_fmt(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, | |
| struct v4l2_subdev_format *fmt) | |
| { | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| const struct ov2732_mode *mode; | |
| s64 vblank_def; | |
| int ret; | |
| mode = v4l2_find_nearest_size(supported_modes, | |
| ARRAY_SIZE(supported_modes), | |
| width, height, | |
| fmt->format.width, fmt->format.height); | |
| fmt->format.code = MEDIA_BUS_FMT_SBGGR10_1X10; | |
| fmt->format.width = mode->width; | |
| fmt->format.height = mode->height; | |
| fmt->format.field = V4L2_FIELD_NONE; | |
| fmt->format.colorspace = V4L2_COLORSPACE_RAW; | |
| fmt->format.ycbcr_enc = V4L2_YCBCR_ENC_601; | |
| fmt->format.quantization = V4L2_QUANTIZATION_FULL_RANGE; | |
| fmt->format.xfer_func = V4L2_XFER_FUNC_NONE; | |
| *v4l2_subdev_state_get_format(state, fmt->pad) = fmt->format; | |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) | |
| return 0; | |
| vblank_def = mode->vts - mode->height; | |
| ret = __v4l2_ctrl_modify_range(ov2732->vblank, vblank_def, | |
| OV2732_VTS_MAX - mode->height, 1, | |
| vblank_def); | |
| return ret; | |
| } | |
| static int ov2732_get_selection(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, | |
| struct v4l2_subdev_selection *sel) | |
| { | |
| switch (sel->target) { | |
| case V4L2_SEL_TGT_CROP: | |
| sel->r = *v4l2_subdev_state_get_crop(state, 0); | |
| return 0; | |
| case V4L2_SEL_TGT_NATIVE_SIZE: | |
| case V4L2_SEL_TGT_CROP_DEFAULT: | |
| case V4L2_SEL_TGT_CROP_BOUNDS: | |
| sel->r.top = 0; | |
| sel->r.left = 0; | |
| sel->r.width = OV2732_NATIVE_WIDTH; | |
| sel->r.height = OV2732_NATIVE_HEIGHT; | |
| return 0; | |
| } | |
| return -EINVAL; | |
| } | |
| static int ov2732_enable_streams(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, u32 pad, | |
| u64 streams_mask) | |
| { | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| struct i2c_client *client = v4l2_get_subdevdata(&ov2732->sd); | |
| int ret; | |
| ret = pm_runtime_resume_and_get(&client->dev); | |
| if (ret < 0) | |
| return ret; | |
| /* Set stream off register for PLL changes. */ | |
| ret = cci_write(ov2732->regmap, OV2732_REG_MODE_SELECT, | |
| OV2732_MODE_STANDBY, NULL); | |
| if (ret) | |
| goto err_put_autosuspend; | |
| /* Send all registers that are common to all modes */ | |
| ret = cci_multi_reg_write(ov2732->regmap, ov2732_common_regs, | |
| ARRAY_SIZE(ov2732_common_regs), NULL); | |
| if (ret) { | |
| dev_err(&client->dev, "failed to init registers\n"); | |
| goto err_put_autosuspend; | |
| } | |
| /* Apply customized values from user */ | |
| ret = __v4l2_ctrl_handler_setup(ov2732->sd.ctrl_handler); | |
| if (ret) | |
| goto err_put_autosuspend; | |
| /* Set stream on register */ | |
| ret = cci_write(ov2732->regmap, OV2732_REG_MODE_SELECT, | |
| OV2732_MODE_STREAMING, NULL); | |
| if (ret) | |
| goto err_put_autosuspend; | |
| return 0; | |
| err_put_autosuspend: | |
| pm_runtime_put_autosuspend(&client->dev); | |
| return ret; | |
| } | |
| static int ov2732_disable_streams(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *state, u32 pad, | |
| u64 streams_mask) | |
| { | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| struct i2c_client *client = v4l2_get_subdevdata(&ov2732->sd); | |
| int ret; | |
| /* set stream off register */ | |
| ret = cci_write(ov2732->regmap, OV2732_REG_MODE_SELECT, | |
| OV2732_MODE_STANDBY, NULL); | |
| if (ret) | |
| dev_err(&client->dev, "%s failed to set stream\n", __func__); | |
| /* Wait for 512 cycles as per datasheet. */ | |
| fsleep(OV2732_DELAY_US(OV2732_POWER_DOWN_DELAY_CYCLES)); | |
| pm_runtime_put_autosuspend(&client->dev); | |
| return ret; | |
| } | |
| static const struct v4l2_subdev_video_ops ov2732_video_ops = { | |
| .s_stream = v4l2_subdev_s_stream_helper, | |
| }; | |
| static const struct v4l2_subdev_pad_ops ov2732_pad_ops = { | |
| .enum_mbus_code = ov2732_enum_mbus_code, | |
| .enum_frame_size = ov2732_enum_frame_size, | |
| .get_fmt = v4l2_subdev_get_fmt, | |
| .set_fmt = ov2732_set_fmt, | |
| .get_selection = ov2732_get_selection, | |
| .enable_streams = ov2732_enable_streams, | |
| .disable_streams = ov2732_disable_streams, | |
| }; | |
| static const struct v4l2_subdev_ops ov2732_subdev_ops = { | |
| .video = &ov2732_video_ops, | |
| .pad = &ov2732_pad_ops, | |
| }; | |
| static int ov2732_init_state(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_state *sd_state) | |
| { | |
| struct v4l2_subdev_format fmt = { | |
| .which = V4L2_SUBDEV_FORMAT_TRY, | |
| .format = { | |
| .width = 1920, | |
| .height = 1080, | |
| .code = MEDIA_BUS_FMT_SBGGR10_1X10, | |
| .colorspace = V4L2_COLORSPACE_RAW, | |
| .field = V4L2_FIELD_NONE, | |
| .quantization = V4L2_QUANTIZATION_FULL_RANGE, | |
| .xfer_func = V4L2_XFER_FUNC_NONE, | |
| .ycbcr_enc = V4L2_YCBCR_ENC_601, | |
| } | |
| }; | |
| return ov2732_set_fmt(sd, sd_state, &fmt); | |
| } | |
| static const struct v4l2_subdev_internal_ops ov2732_internal_ops = { | |
| .init_state = ov2732_init_state, | |
| }; | |
| static int ov2732_set_ctrl(struct v4l2_ctrl *ctrl) | |
| { | |
| struct ov2732 *ov2732 = | |
| container_of(ctrl->handler, struct ov2732, ctrl_handler); | |
| struct i2c_client *client = v4l2_get_subdevdata(&ov2732->sd); | |
| const struct v4l2_mbus_framefmt *format; | |
| struct v4l2_subdev_state *state; | |
| int ret = 0; | |
| state = v4l2_subdev_get_locked_active_state(&ov2732->sd); | |
| format = v4l2_subdev_state_get_format(state, 0); | |
| if (ctrl->id == V4L2_CID_VBLANK) { | |
| int exposure_max, exposure_def; | |
| exposure_max = format->height + ctrl->val - | |
| OV2732_EXPOSURE_OFFSET; | |
| exposure_def = exposure_max; | |
| ret = __v4l2_ctrl_modify_range(ov2732->exposure, | |
| OV2732_EXPOSURE_MIN, | |
| exposure_max, | |
| ov2732->exposure->step, | |
| exposure_def); | |
| if (ret) | |
| return ret; | |
| } | |
| if (pm_runtime_get_if_in_use(&client->dev) == 0) | |
| return 0; | |
| switch (ctrl->id) { | |
| case V4L2_CID_ANALOGUE_GAIN: | |
| cci_write(ov2732->regmap, OV2732_REG_ANALOGUE_GAIN, | |
| ctrl->val, &ret); | |
| break; | |
| case V4L2_CID_DIGITAL_GAIN: | |
| cci_write(ov2732->regmap, OV2732_REG_DIGITAL_GAIN, | |
| ctrl->val, &ret); | |
| break; | |
| case V4L2_CID_EXPOSURE: | |
| /* Lowest 4 bits are fraction bits. */ | |
| cci_write(ov2732->regmap, OV2732_REG_EXPOSURE, | |
| (u32)ctrl->val << 4, &ret); | |
| break; | |
| case V4L2_CID_VBLANK: | |
| cci_write(ov2732->regmap, OV2732_REG_VTS, | |
| format->height + ctrl->val, &ret); | |
| break; | |
| case V4L2_CID_TEST_PATTERN: | |
| cci_write(ov2732->regmap, OV2732_REG_TEST_PATTERN, | |
| ov2732_test_pattern_val[ctrl->val], &ret); | |
| break; | |
| default: | |
| dev_info(&client->dev, | |
| "ctrl(id:0x%x,val:0x%x) is not handled\n", | |
| ctrl->id, ctrl->val); | |
| ret = -EINVAL; | |
| break; | |
| } | |
| pm_runtime_put(&client->dev); | |
| return ret; | |
| }; | |
| static const struct v4l2_ctrl_ops ov2732_ctrl_ops = { | |
| .s_ctrl = ov2732_set_ctrl, | |
| }; | |
| static int ov2732_init_controls(struct ov2732 *ov2732) | |
| { | |
| const struct ov2732_mode *mode = &supported_modes[0]; | |
| struct v4l2_ctrl_handler *handler; | |
| struct v4l2_ctrl *ctrl; | |
| struct v4l2_fwnode_device_properties props; | |
| s64 exposure_max, vblank_def, vblank_max; | |
| int ret; | |
| handler = &ov2732->ctrl_handler; | |
| ret = v4l2_ctrl_handler_init(handler, 10); | |
| v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, | |
| OV2732_PIXEL_RATE, OV2732_PIXEL_RATE, | |
| 1, OV2732_PIXEL_RATE); | |
| ctrl = v4l2_ctrl_new_int_menu(handler, &ov2732_ctrl_ops, | |
| V4L2_CID_LINK_FREQ, 0, 0, | |
| link_freq_menu_items); | |
| if (ctrl) | |
| ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY; | |
| ov2732->hblank = v4l2_ctrl_new_std(handler, &ov2732_ctrl_ops, | |
| V4L2_CID_HBLANK, | |
| OV2732_HBLANK_DEFAULT, | |
| OV2732_HBLANK_DEFAULT, | |
| 1, OV2732_HBLANK_DEFAULT); | |
| if (ov2732->hblank) | |
| ov2732->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; | |
| vblank_def = mode->vts - mode->height; | |
| vblank_max = OV2732_VTS_MAX - mode->height; | |
| ov2732->vblank = v4l2_ctrl_new_std(handler, &ov2732_ctrl_ops, | |
| V4L2_CID_VBLANK, | |
| vblank_def, vblank_max, | |
| 1, vblank_def); | |
| exposure_max = mode->vts - OV2732_EXPOSURE_OFFSET; | |
| ov2732->exposure = v4l2_ctrl_new_std(handler, &ov2732_ctrl_ops, | |
| V4L2_CID_EXPOSURE, | |
| OV2732_EXPOSURE_MIN, exposure_max, | |
| 1, OV2732_EXPOSURE_DEFAULT); | |
| v4l2_ctrl_new_std(handler, &ov2732_ctrl_ops, V4L2_CID_ANALOGUE_GAIN, | |
| OV2732_ANALOGUE_GAIN_MIN, OV2732_ANALOGUE_GAIN_MAX, | |
| 1, OV2732_ANALOGUE_GAIN_DEFAULT); | |
| v4l2_ctrl_new_std(handler, &ov2732_ctrl_ops, V4L2_CID_DIGITAL_GAIN, | |
| OV2732_DIGITAL_GAIN_MIN, OV2732_DIGITAL_GAIN_MAX, | |
| 1, OV2732_DIGITAL_GAIN_DEFAULT); | |
| v4l2_ctrl_new_std_menu_items(handler, &ov2732_ctrl_ops, | |
| V4L2_CID_TEST_PATTERN, | |
| ARRAY_SIZE(ov2732_test_pattern_menu) - 1, | |
| 0, 0, ov2732_test_pattern_menu); | |
| if (handler->error) { | |
| ret = handler->error; | |
| dev_err_probe(ov2732->dev, ret, "Control init failed\n"); | |
| goto err_handler_free; | |
| } | |
| ret = v4l2_fwnode_device_parse(ov2732->dev, &props); | |
| if (ret) | |
| goto err_handler_free; | |
| ret = v4l2_ctrl_new_fwnode_properties(handler, &ov2732_ctrl_ops, &props); | |
| if (ret) | |
| goto err_handler_free; | |
| ov2732->sd.ctrl_handler = handler; | |
| return 0; | |
| err_handler_free: | |
| v4l2_ctrl_handler_free(handler); | |
| return ret; | |
| } | |
| static int ov2632_probe_dt(struct ov2732 *ov2732) | |
| { | |
| struct fwnode_handle *ep; | |
| struct fwnode_handle *fwnode = dev_fwnode(ov2732->dev); | |
| struct v4l2_fwnode_endpoint bus_cfg = { | |
| .bus_type = V4L2_MBUS_CSI2_DPHY, | |
| }; | |
| int ret; | |
| ep = fwnode_graph_get_endpoint_by_id(fwnode, 0, 0, 0); | |
| ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg); | |
| fwnode_handle_put(ep); | |
| if (ret) { | |
| dev_err_probe(ov2732->dev, -EINVAL, "could not parse endpoint\n"); | |
| goto err_probe_dt; | |
| } | |
| if (bus_cfg.bus.mipi_csi2.num_data_lanes != OV2732_LANES) { | |
| dev_err(ov2732->dev, "only a 2-lane CSI2 config is supported\n"); | |
| ret = -EINVAL; | |
| } | |
| err_probe_dt: | |
| v4l2_fwnode_endpoint_free(&bus_cfg); | |
| return ret; | |
| } | |
| static int ov2732_get_regulators(struct ov2732 *ov2732) | |
| { | |
| for (unsigned int i = 0; i < ARRAY_SIZE(ov2732_supply_names); i++) | |
| ov2732->supplies[i].supply = ov2732_supply_names[i]; | |
| return devm_regulator_bulk_get(ov2732->dev, | |
| ARRAY_SIZE(ov2732_supply_names), | |
| ov2732->supplies); | |
| } | |
| static int ov2732_probe(struct i2c_client *client) | |
| { | |
| struct ov2732 *ov2732; | |
| int ret; | |
| ov2732 = devm_kzalloc(&client->dev, sizeof(*ov2732), GFP_KERNEL); | |
| if (!ov2732) | |
| return -ENOMEM; | |
| ov2732->dev = &client->dev; | |
| ret = ov2632_probe_dt(ov2732); | |
| if (ret) | |
| return ret; | |
| ov2732->xvclk = devm_v4l2_sensor_clk_get(ov2732->dev, NULL); | |
| if (IS_ERR(ov2732->xvclk)) | |
| return dev_err_probe(ov2732->dev, PTR_ERR(ov2732->xvclk), | |
| "failed to get xvclk\n"); | |
| ov2732->xvclk_freq = clk_get_rate(ov2732->xvclk); | |
| if (ov2732->xvclk_freq != OV2732_XVCLK_FREQ) | |
| return dev_err_probe(ov2732->dev, -EINVAL, | |
| "xvclk frequency not supported: %dHz\n", | |
| ov2732->xvclk_freq); | |
| ov2732->powerdown_gpio = devm_gpiod_get_optional(ov2732->dev, | |
| "powerdown", | |
| GPIOD_OUT_HIGH); | |
| ov2732->reset_gpio = devm_gpiod_get_optional(ov2732->dev, "reset", | |
| GPIOD_OUT_HIGH); | |
| ov2732->regmap = devm_cci_regmap_init_i2c(client, 16); | |
| if (IS_ERR(ov2732->regmap)) | |
| return dev_err_probe(ov2732->dev, PTR_ERR(ov2732->regmap), | |
| "failed to init CCI\n"); | |
| ret = ov2732_get_regulators(ov2732); | |
| if (ret) | |
| return dev_err_probe(ov2732->dev, ret, | |
| "failed to get regulators\n"); | |
| v4l2_i2c_subdev_init(&ov2732->sd, client, &ov2732_subdev_ops); | |
| /* Device must be powered on for ov2732_identify_chip(). */ | |
| ret = ov2732_power_on(ov2732->dev); | |
| if (ret) | |
| return ret; | |
| pm_runtime_set_active(ov2732->dev); | |
| pm_runtime_enable(ov2732->dev); | |
| ret = ov2732_identify_chip(ov2732); | |
| if (ret) | |
| goto err_power_off; | |
| ret = ov2732_init_controls(ov2732); | |
| if (ret) | |
| goto err_power_off; | |
| /* Initialize subdev */ | |
| ov2732->sd.internal_ops = &ov2732_internal_ops; | |
| ov2732->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; | |
| ov2732->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; | |
| /* Initialize source pad */ | |
| ov2732->pad.flags = MEDIA_PAD_FL_SOURCE; | |
| ret = media_entity_pads_init(&ov2732->sd.entity, 1, &ov2732->pad); | |
| if (ret) { | |
| dev_err_probe(ov2732->dev, ret, "failed to init entity pads\n"); | |
| goto error_handler_free; | |
| } | |
| ov2732->sd.state_lock = ov2732->ctrl_handler.lock; | |
| ret = v4l2_subdev_init_finalize(&ov2732->sd); | |
| if (ret < 0) { | |
| dev_err_probe(ov2732->dev, ret, "subdev init error\n"); | |
| goto err_media_entity; | |
| } | |
| ret = v4l2_async_register_subdev_sensor(&ov2732->sd); | |
| if (ret < 0) { | |
| dev_err_probe(ov2732->dev, ret, | |
| "failed to register sensor sub-device\n"); | |
| goto err_subdev_cleanup; | |
| } | |
| pm_runtime_set_autosuspend_delay(ov2732->dev, 1000); | |
| pm_runtime_use_autosuspend(ov2732->dev); | |
| pm_runtime_idle(ov2732->dev); | |
| return 0; | |
| err_subdev_cleanup: | |
| v4l2_subdev_cleanup(&ov2732->sd); | |
| err_media_entity: | |
| media_entity_cleanup(&ov2732->sd.entity); | |
| error_handler_free: | |
| v4l2_ctrl_handler_free(&ov2732->ctrl_handler); | |
| err_power_off: | |
| pm_runtime_disable(ov2732->dev); | |
| pm_runtime_set_suspended(ov2732->dev); | |
| ov2732_power_off(ov2732->dev); | |
| return ret; | |
| } | |
| static void ov2732_remove(struct i2c_client *client) | |
| { | |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); | |
| struct ov2732 *ov2732 = to_ov2732(sd); | |
| v4l2_async_unregister_subdev(sd); | |
| v4l2_subdev_cleanup(sd); | |
| media_entity_cleanup(&sd->entity); | |
| v4l2_ctrl_handler_free(&ov2732->ctrl_handler); | |
| pm_runtime_disable(ov2732->dev); | |
| if (!pm_runtime_status_suspended(ov2732->dev)) { | |
| ov2732_power_off(ov2732->dev); | |
| pm_runtime_set_suspended(ov2732->dev); | |
| } | |
| } | |
| static const struct of_device_id ov2732_of_match[] = { | |
| { .compatible = "ovti,ov2732", }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, ov2732_of_match); | |
| static DEFINE_RUNTIME_DEV_PM_OPS(ov2732_pm_ops, ov2732_power_off, | |
| ov2732_power_on, NULL); | |
| static struct i2c_driver ov2732_i2c_driver = { | |
| .driver = { | |
| .name = "ov2732", | |
| .of_match_table = ov2732_of_match, | |
| .pm = pm_sleep_ptr(&ov2732_pm_ops), | |
| }, | |
| .probe = ov2732_probe, | |
| .remove = ov2732_remove, | |
| }; | |
| module_i2c_driver(ov2732_i2c_driver); | |
| MODULE_DESCRIPTION("OmniVision ov2732 sensor driver"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("Walter Werner Schneider <contact@schnwalter.eu>"); |