| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023, Linaro Limited |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| |
| / { |
| aliases { |
| i2c11 = &i2c11; |
| i2c18 = &i2c18; |
| serial0 = &uart10; |
| serial1 = &uart12; |
| serial2 = &uart17; |
| spi16 = &spi16; |
| ufshc1 = &ufs_mem_hc; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| vreg_12p0: vreg-12p0-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VREG_12P0"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| }; |
| |
| vreg_5p0: vreg-5p0-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VREG_5P0"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| |
| vin-supply = <&vreg_12p0>; |
| }; |
| |
| vreg_1p8: vreg-1p8-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VREG_1P8"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| vin-supply = <&vreg_5p0>; |
| }; |
| |
| vreg_1p0: vreg-1p0-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VREG_1P0"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| |
| vin-supply = <&vreg_1p8>; |
| }; |
| |
| vreg_3p0: vreg-3p0-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "VREG_3P0"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| vin-supply = <&vreg_12p0>; |
| }; |
| |
| vreg_conn_1p8: vreg_conn_1p8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_conn_1p8"; |
| startup-delay-us = <4000>; |
| enable-active-high; |
| gpio = <&pmm8654au_1_gpios 4 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vreg_conn_pa: vreg_conn_pa { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_conn_pa"; |
| startup-delay-us = <4000>; |
| enable-active-high; |
| gpio = <&pmm8654au_1_gpios 6 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| wcn6855-pmu { |
| compatible = "qcom,wcn6855-pmu"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; |
| |
| vddio-supply = <&vreg_conn_pa>; |
| vddaon-supply = <&vreg_l2c>; |
| vddpmu-supply = <&vreg_conn_1p8>; |
| vddrfa0p95-supply = <&vreg_l2c>; |
| vddrfa1p3-supply = <&vreg_l6e>; |
| vddrfa1p9-supply = <&vreg_s5a>; |
| vddpcie1p3-supply = <&vreg_l6e>; |
| vddpcie1p9-supply = <&vreg_s5a>; |
| |
| bt-enable-gpios = <&pmm8654au_1_gpios 8 GPIO_ACTIVE_HIGH>; |
| wlan-enable-gpios = <&pmm8654au_1_gpios 7 GPIO_ACTIVE_HIGH>; |
| |
| regulators { |
| vreg_pmu_rfa_cmn: ldo0 { |
| regulator-name = "vreg_pmu_rfa_cmn"; |
| }; |
| |
| vreg_pmu_aon_0p59: ldo1 { |
| regulator-name = "vreg_pmu_aon_0p59"; |
| }; |
| |
| vreg_pmu_wlcx_0p8: ldo2 { |
| regulator-name = "vreg_pmu_wlcx_0p8"; |
| }; |
| |
| vreg_pmu_wlmx_0p85: ldo3 { |
| regulator-name = "vreg_pmu_wlmx_0p85"; |
| }; |
| |
| vreg_pmu_btcmx_0p85: ldo4 { |
| regulator-name = "vreg_pmu_btcmx_0p85"; |
| }; |
| |
| vreg_pmu_rfa_0p8: ldo5 { |
| regulator-name = "vreg_pmu_rfa_0p8"; |
| }; |
| |
| vreg_pmu_rfa_1p2: ldo6 { |
| regulator-name = "vreg_pmu_rfa_1p2"; |
| }; |
| |
| vreg_pmu_rfa_1p7: ldo7 { |
| regulator-name = "vreg_pmu_rfa_1p7"; |
| }; |
| |
| vreg_pmu_pcie_0p9: ldo8 { |
| regulator-name = "vreg_pmu_pcie_0p9"; |
| }; |
| |
| vreg_pmu_pcie_1p8: ldo9 { |
| regulator-name = "vreg_pmu_pcie_1p8"; |
| }; |
| }; |
| }; |
| |
| dp0-connector { |
| compatible = "dp-connector"; |
| label = "eDP0"; |
| type = "full-size"; |
| |
| port { |
| dp0_connector_in: endpoint { |
| remote-endpoint = <&mdss0_dp0_out>; |
| }; |
| }; |
| }; |
| |
| dp1-connector { |
| compatible = "dp-connector"; |
| label = "eDP1"; |
| type = "full-size"; |
| |
| port { |
| dp1_connector_in: endpoint { |
| remote-endpoint = <&mdss0_dp1_out>; |
| }; |
| }; |
| }; |
| |
| dp-dsi0-connector { |
| compatible = "dp-connector"; |
| label = "DSI0"; |
| type = "full-size"; |
| |
| port { |
| dp_dsi0_connector_in: endpoint { |
| remote-endpoint = <&dsi2dp_bridge0_out>; |
| }; |
| }; |
| }; |
| |
| dp-dsi1-connector { |
| compatible = "dp-connector"; |
| label = "DSI1"; |
| type = "full-size"; |
| |
| port { |
| dp_dsi1_connector_in: endpoint { |
| remote-endpoint = <&dsi2dp_bridge1_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pmm8654au-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vreg_s4a: smps4 { |
| regulator-name = "vreg_s4a"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1816000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s5a: smps5 { |
| regulator-name = "vreg_s5a"; |
| regulator-min-microvolt = <1850000>; |
| regulator-max-microvolt = <1996000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s9a: smps9 { |
| regulator-name = "vreg_s9a"; |
| regulator-min-microvolt = <535000>; |
| regulator-max-microvolt = <1120000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4a: ldo4 { |
| regulator-name = "vreg_l4a"; |
| regulator-min-microvolt = <788000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5a: ldo5 { |
| regulator-name = "vreg_l5a"; |
| regulator-min-microvolt = <870000>; |
| regulator-max-microvolt = <950000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6a: ldo6 { |
| regulator-name = "vreg_l6a"; |
| regulator-min-microvolt = <870000>; |
| regulator-max-microvolt = <970000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a: ldo7 { |
| regulator-name = "vreg_l7a"; |
| regulator-min-microvolt = <720000>; |
| regulator-max-microvolt = <950000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8a: ldo8 { |
| regulator-name = "vreg_l8a"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a: ldo9 { |
| regulator-name = "vreg_l9a"; |
| regulator-min-microvolt = <2970000>; |
| regulator-max-microvolt = <3544000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pmm8654au-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vreg_l1c: ldo1 { |
| regulator-name = "vreg_l1c"; |
| regulator-min-microvolt = <1140000>; |
| regulator-max-microvolt = <1260000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c: ldo2 { |
| regulator-name = "vreg_l2c"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c: ldo3 { |
| regulator-name = "vreg_l3c"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c: ldo4 { |
| regulator-name = "vreg_l4c"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| /* |
| * FIXME: This should have regulator-allow-set-load but |
| * we're getting an over-current fault from the PMIC |
| * when switching to LPM. |
| */ |
| }; |
| |
| vreg_l5c: ldo5 { |
| regulator-name = "vreg_l5c"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6c: ldo6 { |
| regulator-name = "vreg_l6c"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <1980000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c: ldo7 { |
| regulator-name = "vreg_l7c"; |
| regulator-min-microvolt = <1620000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8c: ldo8 { |
| regulator-name = "vreg_l8c"; |
| regulator-min-microvolt = <2400000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c: ldo9 { |
| regulator-name = "vreg_l9c"; |
| regulator-min-microvolt = <1650000>; |
| regulator-max-microvolt = <2700000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pmm8654au-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vreg_s4e: smps4 { |
| regulator-name = "vreg_s4e"; |
| regulator-min-microvolt = <970000>; |
| regulator-max-microvolt = <1520000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s7e: smps7 { |
| regulator-name = "vreg_s7e"; |
| regulator-min-microvolt = <1010000>; |
| regulator-max-microvolt = <1170000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s9e: smps9 { |
| regulator-name = "vreg_s9e"; |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <570000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6e: ldo6 { |
| regulator-name = "vreg_l6e"; |
| regulator-min-microvolt = <1280000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8e: ldo8 { |
| regulator-name = "vreg_l8e"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1950000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| }; |
| |
| &gpu_zap_shader { |
| firmware-name = "qcom/sa8775p/a663_zap.mbn"; |
| }; |
| |
| &i2c11 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| }; |
| |
| &i2c18 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| io_expander: gpio@74 { |
| compatible = "ti,tca9539"; |
| reg = <0x74>; |
| interrupts-extended = <&tlmm 98 IRQ_TYPE_EDGE_BOTH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reset-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&io_expander_intr_active>, |
| <&io_expander_reset_active>; |
| pinctrl-names = "default"; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9543"; |
| #address-cells = <1>; |
| |
| #size-cells = <0>; |
| reg = <0x70>; |
| |
| i2c@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bridge@58 { |
| compatible = "analogix,anx7625"; |
| reg = <0x58>; |
| interrupts-extended = <&io_expander 2 IRQ_TYPE_EDGE_FALLING>; |
| enable-gpios = <&io_expander 1 GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>; |
| vdd10-supply = <&vreg_1p0>; |
| vdd18-supply = <&vreg_1p8>; |
| vdd33-supply = <&vreg_3p0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| dsi2dp_bridge0_in: endpoint { |
| remote-endpoint = <&mdss0_dsi0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| dsi2dp_bridge0_out: endpoint { |
| remote-endpoint = <&dp_dsi0_connector_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| i2c@1 { |
| reg = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bridge@58 { |
| compatible = "analogix,anx7625"; |
| reg = <0x58>; |
| interrupts-extended = <&io_expander 10 IRQ_TYPE_EDGE_FALLING>; |
| enable-gpios = <&io_expander 9 GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&io_expander 8 GPIO_ACTIVE_HIGH>; |
| vdd10-supply = <&vreg_1p0>; |
| vdd18-supply = <&vreg_1p8>; |
| vdd33-supply = <&vreg_3p0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| dsi2dp_bridge1_in: endpoint { |
| remote-endpoint = <&mdss0_dsi1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| dsi2dp_bridge1_out: endpoint { |
| remote-endpoint = <&dp_dsi1_connector_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| &iris { |
| firmware-name = "qcom/vpu/vpu30_p4_s6.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0 { |
| status = "okay"; |
| }; |
| |
| &mdss0_dp0 { |
| pinctrl-0 = <&dp0_hot_plug_det>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dp0_out { |
| data-lanes = <0 1 2 3>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| remote-endpoint = <&dp0_connector_in>; |
| }; |
| |
| &mdss0_dp0_phy { |
| vdda-phy-supply = <&vreg_l1c>; |
| vdda-pll-supply = <&vreg_l4a>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dp1 { |
| pinctrl-0 = <&dp1_hot_plug_det>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dp1_out { |
| data-lanes = <0 1 2 3>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| remote-endpoint = <&dp1_connector_in>; |
| }; |
| |
| &mdss0_dp1_phy { |
| vdda-phy-supply = <&vreg_l1c>; |
| vdda-pll-supply = <&vreg_l4a>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dsi0 { |
| vdda-supply = <&vreg_l1c>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dsi0_out { |
| data-lanes = <0 1 2 3>; |
| remote-endpoint = <&dsi2dp_bridge0_in>; |
| }; |
| |
| &mdss0_dsi0_phy { |
| vdds-supply = <&vreg_l4a>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dsi1 { |
| vdda-supply = <&vreg_l1c>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss0_dsi1_out { |
| data-lanes = <0 1 2 3>; |
| remote-endpoint = <&dsi2dp_bridge1_in>; |
| }; |
| |
| &mdss0_dsi1_phy { |
| vdds-supply = <&vreg_l4a>; |
| |
| status = "okay"; |
| }; |
| |
| &pmm8654au_0_gpios { |
| gpio-line-names = "DS_EN", |
| "POFF_COMPLETE", |
| "UFS0_VER_ID", |
| "FAST_POFF", |
| "DBU1_PON_DONE", |
| "AOSS_SLEEP", |
| "CAM_DES0_EN", |
| "CAM_DES1_EN", |
| "CAM_DES2_EN", |
| "CAM_DES3_EN", |
| "UEFI", |
| "ANALOG_PON_OPT"; |
| }; |
| |
| &pmm8654au_0_pon_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pmm8654au_1_gpios { |
| gpio-line-names = "PMIC_C_ID0", |
| "PMIC_C_ID1", |
| "UFS1_VER_ID", |
| "IPA_PWR", |
| "", |
| "WLAN_DBU4_EN", |
| "WLAN_EN", |
| "BT_EN", |
| "USB2_PWR_EN", |
| "USB2_FAULT"; |
| |
| wlan_en_state: wlan-en-state { |
| pins = "gpio7"; |
| function = "normal"; |
| output-low; |
| bias-pull-down; |
| }; |
| |
| bt_en_state: bt-en-state { |
| pins = "gpio8"; |
| function = "normal"; |
| output-low; |
| bias-pull-down; |
| }; |
| |
| usb2_en_state: usb2-en-state { |
| pins = "gpio9"; |
| function = "normal"; |
| output-high; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pmm8654au_2_gpios { |
| gpio-line-names = "PMIC_E_ID0", |
| "PMIC_E_ID1", |
| "USB0_PWR_EN", |
| "USB0_FAULT", |
| "SENSOR_IRQ_1", |
| "SENSOR_IRQ_2", |
| "SENSOR_RST", |
| "SGMIIO0_RST", |
| "SGMIIO1_RST", |
| "USB1_PWR_ENABLE", |
| "USB1_FAULT", |
| "VMON_SPX8"; |
| |
| usb0_en_state: usb0-en-state { |
| pins = "gpio3"; |
| function = "normal"; |
| output-high; |
| power-source = <0>; |
| }; |
| |
| usb1_en_state: usb1-en-state { |
| pins = "gpio10"; |
| function = "normal"; |
| output-high; |
| power-source = <0>; |
| }; |
| }; |
| |
| &pmm8654au_3_gpios { |
| gpio-line-names = "PMIC_G_ID0", |
| "PMIC_G_ID1", |
| "GNSS_RST", |
| "GNSS_EN", |
| "GNSS_BOOT_MODE"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_2 { |
| status = "okay"; |
| }; |
| |
| &qup_spi16_default { |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| &qup_i2c11_default { |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| &qup_i2c18_default { |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| &qup_uart12_cts { |
| bias-disable; |
| }; |
| |
| &qup_uart12_rts { |
| bias-pull-down; |
| }; |
| |
| &qup_uart12_tx { |
| bias-pull-up; |
| }; |
| |
| &qup_uart12_rx { |
| bias-pull-down; |
| }; |
| |
| &qup_uart17_cts { |
| bias-disable; |
| }; |
| |
| &qup_uart17_rts { |
| bias-pull-down; |
| }; |
| |
| &qup_uart17_tx { |
| bias-pull-up; |
| }; |
| |
| &qup_uart17_rx { |
| bias-pull-down; |
| }; |
| |
| &serdes0 { |
| phy-supply = <&vreg_l5a>; |
| status = "okay"; |
| }; |
| |
| &serdes1 { |
| phy-supply = <&vreg_l5a>; |
| status = "okay"; |
| }; |
| |
| &sleep_clk { |
| clock-frequency = <32000>; |
| }; |
| |
| &spi16 { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| dp0_hot_plug_det: dp0-hot-plug-det-state { |
| pins = "gpio101"; |
| function = "edp0_hot"; |
| bias-disable; |
| }; |
| |
| dp1_hot_plug_det: dp1-hot-plug-det-state { |
| pins = "gpio102"; |
| function = "edp1_hot"; |
| bias-disable; |
| }; |
| |
| io_expander_intr_active: io-expander-intr-active-state { |
| pins = "gpio98"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| io_expander_reset_active: io-expander-reset-active-state { |
| pins = "gpio97"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| |
| pcie0_default_state: pcie0-default-state { |
| perst-pins { |
| pins = "gpio2"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| clkreq-pins { |
| pins = "gpio1"; |
| function = "pcie0_clkreq"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| wake-pins { |
| pins = "gpio0"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie1_default_state: pcie1-default-state { |
| perst-pins { |
| pins = "gpio4"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| clkreq-pins { |
| pins = "gpio3"; |
| function = "pcie1_clkreq"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| wake-pins { |
| pins = "gpio5"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| &pcie0 { |
| perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie0_default_state>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie1 { |
| perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie1_default_state>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie0_phy { |
| vdda-phy-supply = <&vreg_l5a>; |
| vdda-pll-supply = <&vreg_l1c>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie1_phy { |
| vdda-phy-supply = <&vreg_l5a>; |
| vdda-pll-supply = <&vreg_l1c>; |
| |
| status = "okay"; |
| }; |
| |
| &pcieport0 { |
| wifi@0 { |
| compatible = "pci17cb,1101"; |
| reg = <0x10000 0x0 0x0 0x0 0x0>; |
| |
| qcom,calibration-variant = "QC_SA8775P_Ride"; |
| |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>; |
| vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; |
| vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/sa8775p/adsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp0 { |
| firmware-name = "qcom/sa8775p/cdsp0.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp1 { |
| firmware-name = "qcom/sa8775p/cdsp1.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_gpdsp0 { |
| firmware-name = "qcom/sa8775p/gpdsp0.mbn"; |
| status = "okay"; |
| }; |
| |
| &remoteproc_gpdsp1 { |
| firmware-name = "qcom/sa8775p/gpdsp1.mbn"; |
| status = "okay"; |
| }; |
| |
| &uart10 { |
| compatible = "qcom,geni-debug-uart"; |
| status = "okay"; |
| }; |
| |
| &uart12 { |
| pinctrl-0 = <&qup_uart12_default>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &uart17 { |
| pinctrl-0 = <&qup_uart17_default>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn6855-bt"; |
| firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; |
| |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>; |
| }; |
| }; |
| |
| &ufs_mem_hc { |
| reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>; |
| vcc-supply = <&vreg_l8a>; |
| vcc-max-microamp = <1100000>; |
| vccq-supply = <&vreg_l4c>; |
| vccq-max-microamp = <1200000>; |
| |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vreg_l4a>; |
| vdda-pll-supply = <&vreg_l1c>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb0_en_state>; |
| dr_mode = "peripheral"; |
| |
| status = "okay"; |
| }; |
| |
| &usb_0_hsphy { |
| vdda-pll-supply = <&vreg_l7a>; |
| vdda18-supply = <&vreg_l6c>; |
| vdda33-supply = <&vreg_l9a>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_0_qmpphy { |
| vdda-phy-supply = <&vreg_l1c>; |
| vdda-pll-supply = <&vreg_l7a>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb1_en_state>; |
| dr_mode = "host"; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_hsphy { |
| vdda-pll-supply = <&vreg_l7a>; |
| vdda18-supply = <&vreg_l6c>; |
| vdda33-supply = <&vreg_l9a>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vreg_l1c>; |
| vdda-pll-supply = <&vreg_l7a>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb2_en_state>; |
| dr_mode = "host"; |
| |
| status = "okay"; |
| }; |
| |
| &usb_2_hsphy { |
| vdda-pll-supply = <&vreg_l7a>; |
| vdda18-supply = <&vreg_l6c>; |
| vdda33-supply = <&vreg_l9a>; |
| |
| status = "okay"; |
| }; |
| |
| &xo_board_clk { |
| clock-frequency = <38400000>; |
| }; |
