| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2022 NXP |
| * Copyright 2023 Variscite Ltd. |
| */ |
| |
| /dts-v1/; |
| |
| #include "imx93.dtsi" |
| |
| /{ |
| model = "Variscite VAR-SOM-MX93 module"; |
| compatible = "variscite,var-som-mx93", "fsl,imx93"; |
| |
| sound { |
| compatible = "simple-audio-card"; |
| simple-audio-card,bitclock-master = <&codec_dai>; |
| simple-audio-card,format = "i2s"; |
| simple-audio-card,frame-master = <&codec_dai>; |
| simple-audio-card,name = "wm8904-audio"; |
| simple-audio-card,routing = |
| "Headphone Jack", "HPOUTL", |
| "Headphone Jack", "HPOUTR", |
| "IN2L", "Line In Jack", |
| "IN2R", "Line In Jack", |
| "IN1L", "Microphone Jack", |
| "IN1R", "Microphone Jack"; |
| simple-audio-card,widgets = |
| "Microphone", "Microphone Jack", |
| "Headphone", "Headphone Jack", |
| "Line", "Line In Jack"; |
| simple-audio-card,mclk-fs = <256>; |
| |
| codec_dai: simple-audio-card,codec { |
| sound-dai = <&wm8904>; |
| }; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&sai1>; |
| }; |
| }; |
| |
| usdhc3_pwrseq: mmc-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| post-power-on-delay-ms = <100>; |
| power-off-delay-us = <10000>; |
| reset-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>, /* WIFI_RESET */ |
| <&gpio3 7 GPIO_ACTIVE_LOW>; /* WIFI_PWR_EN */ |
| }; |
| }; |
| |
| &eqos { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos>; |
| /* |
| * The required RGMII TX and RX 2ns delays are implemented directly |
| * in hardware via passive delay elements on the SOM PCB. |
| * No delay configuration is needed in software via PHY driver. |
| */ |
| phy-mode = "rgmii"; |
| phy-handle = <ðphy0>; |
| snps,clk-csr = <5>; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <1000000>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| eee-broken-1000t; |
| reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <10000>; |
| reset-deassert-us = <100000>; |
| |
| leds { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| color = <LED_COLOR_ID_YELLOW>; |
| function = LED_FUNCTION_LAN; |
| linux,default-trigger = "netdev"; |
| }; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_GREEN>; |
| function = LED_FUNCTION_LAN; |
| linux,default-trigger = "netdev"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &lpi2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "sleep", "gpio"; |
| pinctrl-0 = <&pinctrl_lpi2c3>; |
| pinctrl-1 = <&pinctrl_lpi2c3_gpio>; |
| pinctrl-2 = <&pinctrl_lpi2c3_gpio>; |
| scl-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; |
| sda-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| pmic@25 { |
| compatible = "nxp,pca9451a"; |
| reg = <0x25>; |
| |
| regulators { |
| buck1: BUCK1 { |
| regulator-name = "BUCK1"; |
| regulator-min-microvolt = <650000>; |
| regulator-max-microvolt = <2237500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| buck2: BUCK2 { |
| regulator-name = "BUCK2"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <2187500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| buck4: BUCK4 { |
| regulator-name = "BUCK4"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck5: BUCK5 { |
| regulator-name = "BUCK5"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck6: BUCK6 { |
| regulator-name = "BUCK6"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1: LDO1 { |
| regulator-name = "LDO1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo4: LDO4 { |
| regulator-name = "LDO4"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo5: LDO5 { |
| regulator-name = "LDO5"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| wm8904: audio-codec@1a { |
| compatible = "wlf,wm8904"; |
| reg = <0x1a>; |
| #sound-dai-cells = <0>; |
| clocks = <&clk IMX93_CLK_SAI1_GATE>; |
| clock-names = "mclk"; |
| AVDD-supply = <&buck5>; |
| CPVDD-supply = <&buck5>; |
| DBVDD-supply = <&buck4>; |
| DCVDD-supply = <&buck5>; |
| MICVDD-supply = <&buck5>; |
| wlf,drc-cfg-names = "default", "peaklimiter", "tradition", |
| "soft", "music"; |
| /* |
| * Config registers per name, respectively: |
| * KNEE_IP = 0, KNEE_OP = 0, HI_COMP = 1, LO_COMP = 1 |
| * KNEE_IP = -24, KNEE_OP = -6, HI_COMP = 1/4, LO_COMP = 1 |
| * KNEE_IP = -42, KNEE_OP = -3, HI_COMP = 0, LO_COMP = 1 |
| * KNEE_IP = -45, KNEE_OP = -9, HI_COMP = 1/8, LO_COMP = 1 |
| * KNEE_IP = -30, KNEE_OP = -10.5, HI_COMP = 1/4, LO_COMP = 1 |
| */ |
| wlf,drc-cfg-regs = /bits/ 16 <0x01af 0x3248 0x0000 0x0000>, |
| /bits/ 16 <0x04af 0x324b 0x0010 0x0408>, |
| /bits/ 16 <0x04af 0x324b 0x0028 0x0704>, |
| /bits/ 16 <0x04af 0x324b 0x0018 0x078c>, |
| /bits/ 16 <0x04af 0x324b 0x0010 0x050e>; |
| /* GPIO1 = DMIC_CLK, don't touch others */ |
| wlf,gpio-cfg = <0x0018>, <0xffff>, <0xffff>, <0xffff>; |
| }; |
| }; |
| |
| &lpspi8 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpspi8>; |
| cs-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| /* Resistive touch controller */ |
| ads7846: touchscreen@0 { |
| compatible = "ti,ads7846"; |
| reg = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_restouch>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <29 IRQ_TYPE_EDGE_FALLING>; |
| spi-max-frequency = <1000000>; |
| pendown-gpio = <&gpio4 29 0>; |
| vcc-supply = <&buck5>; |
| ti,x-min = /bits/ 16 <125>; |
| ti,x-max = /bits/ 16 <4008>; |
| ti,y-min = /bits/ 16 <282>; |
| ti,y-max = /bits/ 16 <3864>; |
| ti,x-plate-ohms = /bits/ 16 <180>; |
| ti,pressure-max = /bits/ 16 <255>; |
| ti,debounce-max = /bits/ 16 <10>; |
| ti,debounce-tol = /bits/ 16 <3>; |
| ti,debounce-rep = /bits/ 16 <1>; |
| ti,settle-delay-usec = /bits/ 16 <150>; |
| ti,keep-vref-on; |
| wakeup-source; |
| }; |
| }; |
| |
| /* BT module */ |
| &lpuart5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lpuart5>, <&pinctrl_bluetooth>; |
| uart-has-rtscts; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "nxp,88w8987-bt"; |
| }; |
| }; |
| |
| &sai1 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_sai1>; |
| pinctrl-1 = <&pinctrl_sai1_sleep>; |
| assigned-clocks = <&clk IMX93_CLK_SAI1>; |
| assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>; |
| assigned-clock-rates = <12288000>; |
| fsl,sai-mclk-direction-output; |
| status = "okay"; |
| }; |
| |
| /* eMMC */ |
| &usdhc1 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1>; |
| pinctrl-2 = <&pinctrl_usdhc1>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| /* WiFi */ |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; |
| pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_wlan>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_wlan>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_wlan>; |
| pinctrl-3 = <&pinctrl_usdhc3_sleep>, <&pinctrl_usdhc3_wlan>; |
| bus-width = <4>; |
| mmc-pwrseq = <&usdhc3_pwrseq>; |
| non-removable; |
| wakeup-source; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_bluetooth: bluetoothgrp { |
| fsl,pins = < |
| MX93_PAD_ENET2_MDIO__GPIO4_IO15 0x51e |
| >; |
| }; |
| |
| pinctrl_eqos: eqosgrp { |
| fsl,pins = < |
| MX93_PAD_ENET1_MDC__ENET_QOS_MDC 0x57e |
| MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x57e |
| MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e |
| MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e |
| MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e |
| MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e |
| MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x58e |
| MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e |
| MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x57e |
| MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1 0x57e |
| MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x57e |
| MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x57e |
| MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x58e |
| MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x57e |
| MX93_PAD_UART2_TXD__GPIO1_IO07 0x51e |
| >; |
| }; |
| |
| pinctrl_reg_eqos_phy: regeqosgrp { |
| fsl,pins = < |
| MX93_PAD_UART2_TXD__GPIO1_IO07 0x51e |
| >; |
| }; |
| |
| pinctrl_lpi2c3: lpi2c3grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e |
| MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_lpi2c3_gpio: lpi2c3-gpiogrp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO28__GPIO2_IO28 0x40000b9e |
| MX93_PAD_GPIO_IO29__GPIO2_IO29 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_lpspi8: lpspi8grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO12__GPIO2_IO12 0x31e |
| MX93_PAD_GPIO_IO13__LPSPI8_SIN 0x31e |
| MX93_PAD_GPIO_IO14__LPSPI8_SOUT 0x31e |
| MX93_PAD_GPIO_IO15__LPSPI8_SCK 0x31e |
| >; |
| }; |
| |
| pinctrl_lpuart5: lpuart5grp { |
| fsl,pins = < |
| MX93_PAD_DAP_TDO_TRACESWO__LPUART5_TX 0x31e |
| MX93_PAD_DAP_TDI__LPUART5_RX 0x31e |
| MX93_PAD_DAP_TMS_SWDIO__LPUART5_RTS_B 0x31e |
| MX93_PAD_DAP_TCLK_SWCLK__LPUART5_CTS_B 0x31e |
| >; |
| }; |
| |
| pinctrl_restouch: restouchgrp { |
| fsl,pins = < |
| MX93_PAD_CCM_CLKO4__GPIO4_IO29 0x31e |
| >; |
| }; |
| |
| pinctrl_sai1: sai1grp { |
| fsl,pins = < |
| MX93_PAD_SAI1_TXC__SAI1_TX_BCLK 0x31e |
| MX93_PAD_SAI1_TXFS__SAI1_TX_SYNC 0x31e |
| MX93_PAD_SAI1_TXD0__SAI1_TX_DATA00 0x31e |
| MX93_PAD_SAI1_RXD0__SAI1_RX_DATA00 0x31e |
| MX93_PAD_I2C2_SDA__SAI1_RX_BCLK 0x31e |
| MX93_PAD_I2C2_SCL__SAI1_RX_SYNC 0x31e |
| MX93_PAD_UART2_RXD__SAI1_MCLK 0x31e |
| >; |
| }; |
| |
| pinctrl_sai1_sleep: sai1-sleepgrp { |
| fsl,pins = < |
| MX93_PAD_SAI1_TXC__GPIO1_IO12 0x31e |
| MX93_PAD_SAI1_TXFS__GPIO1_IO11 0x31e |
| MX93_PAD_SAI1_TXD0__GPIO1_IO13 0x31e |
| MX93_PAD_SAI1_RXD0__GPIO1_IO14 0x31e |
| MX93_PAD_UART2_RXD__GPIO1_IO06 0x31e |
| MX93_PAD_I2C2_SDA__GPIO1_IO03 0x31e |
| MX93_PAD_I2C2_SCL__GPIO1_IO02 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX93_PAD_SD1_CLK__USDHC1_CLK 0x15fe |
| MX93_PAD_SD1_CMD__USDHC1_CMD 0x13fe |
| MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe |
| MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe |
| MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe |
| MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe |
| MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe |
| MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe |
| MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe |
| MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe |
| MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX93_PAD_SD3_CLK__USDHC3_CLK 0x1582 /* SDIO_B_CLK */ |
| MX93_PAD_SD3_CMD__USDHC3_CMD 0x40001382 /* SDIO_B_CMD */ |
| MX93_PAD_SD3_DATA0__USDHC3_DATA0 0x40001382 /* SDIO_B_D0 */ |
| MX93_PAD_SD3_DATA1__USDHC3_DATA1 0x40001382 /* SDIO_B_D1 */ |
| MX93_PAD_SD3_DATA2__USDHC3_DATA2 0x40001382 /* SDIO_B_D2 */ |
| MX93_PAD_SD3_DATA3__USDHC3_DATA3 0x40001382 /* SDIO_B_D3 */ |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = < |
| MX93_PAD_SD3_CLK__USDHC3_CLK 0x158e /* SDIO_B_CLK */ |
| MX93_PAD_SD3_CMD__USDHC3_CMD 0x4000138e /* SDIO_B_CMD */ |
| MX93_PAD_SD3_DATA0__USDHC3_DATA0 0x4000138e /* SDIO_B_D0 */ |
| MX93_PAD_SD3_DATA1__USDHC3_DATA1 0x4000138e /* SDIO_B_D1 */ |
| MX93_PAD_SD3_DATA2__USDHC3_DATA2 0x4000138e /* SDIO_B_D2 */ |
| MX93_PAD_SD3_DATA3__USDHC3_DATA3 0x4000138e /* SDIO_B_D3 */ |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = < |
| MX93_PAD_SD3_CLK__USDHC3_CLK 0x15fe /* SDIO_B_CLK */ |
| MX93_PAD_SD3_CMD__USDHC3_CMD 0x400013fe /* SDIO_B_CMD */ |
| MX93_PAD_SD3_DATA0__USDHC3_DATA0 0x400013fe /* SDIO_B_D0 */ |
| MX93_PAD_SD3_DATA1__USDHC3_DATA1 0x400013fe /* SDIO_B_D1 */ |
| MX93_PAD_SD3_DATA2__USDHC3_DATA2 0x400013fe /* SDIO_B_D2 */ |
| MX93_PAD_SD3_DATA3__USDHC3_DATA3 0x400013fe /* SDIO_B_D3 */ |
| >; |
| }; |
| |
| pinctrl_usdhc3_sleep: usdhc3-sleepgrp { |
| fsl,pins = < |
| MX93_PAD_SD3_CLK__GPIO3_IO20 0x400 |
| MX93_PAD_SD3_CMD__GPIO3_IO21 0x400 |
| MX93_PAD_SD3_DATA0__GPIO3_IO22 0x400 |
| MX93_PAD_SD3_DATA1__GPIO3_IO23 0x400 |
| MX93_PAD_SD3_DATA2__GPIO3_IO24 0x400 |
| MX93_PAD_SD3_DATA3__GPIO3_IO25 0x400 |
| >; |
| }; |
| |
| pinctrl_usdhc3_wlan: usdhc3-wlangrp { |
| fsl,pins = < |
| MX93_PAD_ENET2_MDC__GPIO4_IO14 0x51e /* WIFI_REG_ON */ |
| MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x51e /* WIFI_PWR_EN */ |
| >; |
| }; |
| }; |
