| # SPDX-License-Identifier: GPL-2.0-only | |
| menuconfig ARCH_OMAP1 | |
| bool "TI OMAP1" | |
| depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 | |
| depends on CPU_LITTLE_ENDIAN | |
| depends on ATAGS | |
| select ARCH_OMAP | |
| select CLKSRC_MMIO | |
| select FORCE_PCI if PCCARD | |
| select GENERIC_IRQ_CHIP | |
| select GPIOLIB | |
| help | |
| Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx) | |
| if ARCH_OMAP1 | |
| menu "TI OMAP1 specific features" | |
| comment "OMAP Core Type" | |
| config ARCH_OMAP15XX | |
| depends on ARCH_MULTI_V4T | |
| default y | |
| bool "OMAP15xx Based System" | |
| select CPU_ARM925T | |
| select OMAP_MPU_TIMER | |
| config ARCH_OMAP16XX | |
| depends on ARCH_MULTI_V5 | |
| bool "OMAP16xx Based System" | |
| select ARCH_OMAP_OTG | |
| select CPU_ARM926T | |
| select OMAP_DM_TIMER | |
| config ARCH_OMAP | |
| bool | |
| comment "OMAP Feature Selections" | |
| config OMAP_MUX | |
| bool "OMAP multiplexing support" | |
| default y | |
| help | |
| Pin multiplexing support for OMAP boards. If your bootloader | |
| sets the multiplexing correctly, say N. Otherwise, or if unsure, | |
| say Y. | |
| config OMAP_MUX_DEBUG | |
| bool "Multiplexing debug output" | |
| depends on OMAP_MUX | |
| help | |
| Makes the multiplexing functions print out a lot of debug info. | |
| This is useful if you want to find out the correct values of the | |
| multiplexing registers. | |
| config OMAP_MUX_WARNINGS | |
| bool "Warn about pins the bootloader didn't set up" | |
| depends on OMAP_MUX | |
| default y | |
| help | |
| Choose Y here to warn whenever driver initialization logic needs | |
| to change the pin multiplexing setup. When there are no warnings | |
| printed, it's safe to deselect OMAP_MUX for your product. | |
| config OMAP_32K_TIMER | |
| bool "Use 32KHz timer" | |
| depends on ARCH_OMAP16XX | |
| default ARCH_OMAP16XX | |
| help | |
| Select this option if you want to enable the OMAP 32KHz timer. | |
| This timer saves power compared to the OMAP_MPU_TIMER, and has | |
| support for no tick during idle. The 32KHz timer provides less | |
| intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is | |
| currently only available for OMAP16XX, 24XX, 34XX, OMAP4/5 and DRA7XX. | |
| On OMAP2PLUS this value is only used for CONFIG_HZ and | |
| timer frequency compile time calculation. | |
| The actual timer selection is done in the board file | |
| through the (DT_)MACHINE_START structure. | |
| config OMAP_MPU_TIMER | |
| bool "Use mpu timer" | |
| depends on ARCH_OMAP1 | |
| help | |
| Select this option if you want to use the OMAP mpu timer. This | |
| timer provides more intra-tick resolution than the 32KHz timer, | |
| but consumes more power. | |
| config OMAP_SERIAL_WAKE | |
| bool "Enable wake-up events for serial ports" | |
| depends on ARCH_OMAP1 && OMAP_MUX | |
| default y | |
| help | |
| Select this option if you want to have your system wake up | |
| to data on the serial RX line. This allows you to wake the | |
| system from serial console. | |
| config OMAP_RESET_CLOCKS | |
| bool "Reset unused clocks during boot" | |
| depends on ARCH_OMAP | |
| help | |
| Say Y if you want to reset unused clocks during boot. | |
| This option saves power, but assumes all drivers are | |
| using the clock framework. Broken drivers that do not | |
| yet use clock framework may not work with this option. | |
| If you are booting from another operating system, you | |
| probably do not want this option enabled until your | |
| device drivers work properly. | |
| config ARCH_OMAP_OTG | |
| bool | |
| comment "OMAP Board Type" | |
| config MACH_OMAP_OSK | |
| bool "TI OSK Support" | |
| depends on ARCH_OMAP16XX | |
| help | |
| TI OMAP 5912 OSK (OMAP Starter Kit) board support. Say Y here | |
| if you have such a board. | |
| config MACH_OMAP_PALMTE | |
| bool "Palm Tungsten E" | |
| depends on ARCH_OMAP15XX | |
| help | |
| Support for the Palm Tungsten E PDA. To boot the kernel, you'll | |
| need a PalmOS compatible bootloader; check out | |
| http://palmtelinux.sourceforge.net/ for more information. | |
| Say Y here if you have this PDA model, say N otherwise. | |
| config MACH_SX1 | |
| bool "Siemens SX1" | |
| depends on ARCH_OMAP15XX | |
| select I2C | |
| help | |
| Support for the Siemens SX1 phone. To boot the kernel, | |
| you'll need a SX1 compatible bootloader; check out | |
| http://forum.oslik.ru and | |
| https://www.handhelds.org/moin/moin.cgi/SiemensSX1 | |
| for more information. | |
| Say Y here if you have such a phone, say NO otherwise. | |
| config MACH_NOKIA770 | |
| bool "Nokia 770" | |
| depends on ARCH_OMAP16XX | |
| help | |
| Support for the Nokia 770 Internet Tablet. Say Y here if you | |
| have such a device. | |
| config MACH_AMS_DELTA | |
| bool "Amstrad E3 (Delta)" | |
| depends on ARCH_OMAP15XX | |
| select FIQ | |
| select GPIO_GENERIC_PLATFORM | |
| select LEDS_GPIO_REGISTER | |
| select REGULATOR | |
| select REGULATOR_FIXED_VOLTAGE | |
| help | |
| Support for the Amstrad E3 (codename Delta) videophone. Say Y here | |
| if you have such a device. | |
| endmenu | |
| endif |