| // SPDX-License-Identifier: GPL-2.0 | |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> | |
| #include <dt-bindings/interrupt-controller/irq.h> | |
| #include <dt-bindings/spmi/spmi.h> | |
| / { | |
| thermal-zones { | |
| pm8941-thermal { | |
| polling-delay-passive = <100>; | |
| polling-delay = <0>; | |
| thermal-sensors = <&pm8941_temp>; | |
| trips { | |
| trip0 { | |
| temperature = <105000>; | |
| hysteresis = <2000>; | |
| type = "passive"; | |
| }; | |
| trip1 { | |
| temperature = <125000>; | |
| hysteresis = <2000>; | |
| type = "hot"; | |
| }; | |
| crit { | |
| temperature = <145000>; | |
| hysteresis = <2000>; | |
| type = "critical"; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| &spmi_bus { | |
| pm8941_0: pm8941@0 { | |
| compatible = "qcom,pm8941", "qcom,spmi-pmic"; | |
| reg = <0x0 SPMI_USID>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| rtc@6000 { | |
| compatible = "qcom,pm8941-rtc"; | |
| reg = <0x6000>, | |
| <0x6100>; | |
| reg-names = "rtc", "alarm"; | |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; | |
| }; | |
| pon@800 { | |
| compatible = "qcom,pm8941-pon"; | |
| reg = <0x800>; | |
| pwrkey { | |
| compatible = "qcom,pm8941-pwrkey"; | |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; | |
| debounce = <15625>; | |
| bias-pull-up; | |
| }; | |
| pm8941_resin: resin { | |
| compatible = "qcom,pm8941-resin"; | |
| interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; | |
| debounce = <15625>; | |
| bias-pull-up; | |
| status = "disabled"; | |
| }; | |
| }; | |
| usb_id: usb-detect@900 { | |
| compatible = "qcom,pm8941-misc"; | |
| reg = <0x900>; | |
| interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; | |
| interrupt-names = "usb_id"; | |
| }; | |
| smbb: charger@1000 { | |
| compatible = "qcom,pm8941-charger"; | |
| reg = <0x1000>; | |
| interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, | |
| <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; | |
| interrupt-names = "chg-done", | |
| "chg-fast", | |
| "chg-trkl", | |
| "bat-temp-ok", | |
| "bat-present", | |
| "chg-gone", | |
| "usb-valid", | |
| "dc-valid"; | |
| usb-otg-in-supply = <&pm8941_5vs1>; | |
| status = "disabled"; | |
| chg_otg: otg-vbus { }; | |
| }; | |
| pm8941_gpios: gpio@c000 { | |
| compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio"; | |
| reg = <0xc000>; | |
| gpio-controller; | |
| gpio-ranges = <&pm8941_gpios 0 0 36>; | |
| #gpio-cells = <2>; | |
| interrupt-controller; | |
| #interrupt-cells = <2>; | |
| boost_bypass_n_pin: boost-bypass-state { | |
| pins = "gpio21"; | |
| function = "normal"; | |
| }; | |
| }; | |
| pm8941_mpps: mpps@a000 { | |
| compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp"; | |
| reg = <0xa000>; | |
| gpio-controller; | |
| #gpio-cells = <2>; | |
| gpio-ranges = <&pm8941_mpps 0 0 8>; | |
| interrupt-controller; | |
| #interrupt-cells = <2>; | |
| }; | |
| pm8941_temp: temp-alarm@2400 { | |
| compatible = "qcom,spmi-temp-alarm"; | |
| reg = <0x2400>; | |
| interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; | |
| io-channels = <&pm8941_vadc VADC_DIE_TEMP>; | |
| io-channel-names = "thermal"; | |
| #thermal-sensor-cells = <0>; | |
| }; | |
| pm8941_vadc: adc@3100 { | |
| compatible = "qcom,spmi-vadc"; | |
| reg = <0x3100>; | |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| #io-channel-cells = <1>; | |
| channel@6 { | |
| reg = <VADC_VBAT_SNS>; | |
| }; | |
| channel@8 { | |
| reg = <VADC_DIE_TEMP>; | |
| }; | |
| channel@9 { | |
| reg = <VADC_REF_625MV>; | |
| }; | |
| channel@a { | |
| reg = <VADC_REF_1250MV>; | |
| }; | |
| channel@e { | |
| reg = <VADC_GND_REF>; | |
| }; | |
| channel@f { | |
| reg = <VADC_VDD_VADC>; | |
| }; | |
| channel@30 { | |
| reg = <VADC_LR_MUX1_BAT_THERM>; | |
| }; | |
| }; | |
| pm8941_iadc: adc@3600 { | |
| compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc"; | |
| reg = <0x3600>; | |
| interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; | |
| qcom,external-resistor-micro-ohms = <10000>; | |
| }; | |
| pm8941_coincell: charger@2800 { | |
| compatible = "qcom,pm8941-coincell"; | |
| reg = <0x2800>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| pm8941_1: pm8941@1 { | |
| compatible = "qcom,pm8941", "qcom,spmi-pmic"; | |
| reg = <0x1 SPMI_USID>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| pm8941_lpg: pwm { | |
| compatible = "qcom,pm8941-lpg"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| #pwm-cells = <2>; | |
| status = "disabled"; | |
| }; | |
| pm8941_vib: vibrator@c000 { | |
| compatible = "qcom,pm8916-vib"; | |
| reg = <0xc000>; | |
| status = "disabled"; | |
| }; | |
| pm8941_wled: wled@d800 { | |
| compatible = "qcom,pm8941-wled"; | |
| reg = <0xd800>; | |
| label = "backlight"; | |
| status = "disabled"; | |
| }; | |
| regulators { | |
| compatible = "qcom,pm8941-regulators"; | |
| interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>; | |
| interrupt-names = "ocp-5vs1", "ocp-5vs2"; | |
| vin_5vs-supply = <&pm8941_5v>; | |
| pm8941_5v: s4 { | |
| regulator-min-microvolt = <5000000>; | |
| regulator-max-microvolt = <5000000>; | |
| regulator-enable-ramp-delay = <500>; | |
| }; | |
| pm8941_5vs1: 5vs1 { | |
| regulator-enable-ramp-delay = <1000>; | |
| regulator-pull-down; | |
| regulator-over-current-protection; | |
| qcom,ocp-max-retries = <10>; | |
| qcom,ocp-retry-delay = <30>; | |
| qcom,vs-soft-start-strength = <0>; | |
| regulator-initial-mode = <1>; | |
| }; | |
| pm8941_5vs2: 5vs2 { | |
| regulator-enable-ramp-delay = <1000>; | |
| regulator-pull-down; | |
| regulator-over-current-protection; | |
| qcom,ocp-max-retries = <10>; | |
| qcom,ocp-retry-delay = <30>; | |
| qcom,vs-soft-start-strength = <0>; | |
| regulator-initial-mode = <1>; | |
| }; | |
| }; | |
| }; | |
| }; |