| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * at91sam9261ek.dts - Device Tree file for Atmel at91sam9261 reference board | |
| * | |
| * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com> | |
| */ | |
| /dts-v1/; | |
| #include "at91sam9261.dtsi" | |
| / { | |
| model = "Atmel at91sam9261ek"; | |
| compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9"; | |
| chosen { | |
| bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw"; | |
| stdout-path = "serial0:115200n8"; | |
| }; | |
| memory@20000000 { | |
| reg = <0x20000000 0x4000000>; | |
| }; | |
| clocks { | |
| slow_xtal { | |
| clock-frequency = <32768>; | |
| }; | |
| main_xtal { | |
| clock-frequency = <18432000>; | |
| }; | |
| }; | |
| ahb { | |
| usb0: usb@500000 { | |
| status = "okay"; | |
| }; | |
| fb0: fb@600000 { | |
| display = <&display0>; | |
| atmel,power-control-gpio = <&pioA 12 GPIO_ACTIVE_LOW>; | |
| status = "okay"; | |
| display0: panel { | |
| bits-per-pixel = <16>; | |
| atmel,lcdcon-backlight; | |
| atmel,dmacon = <0x1>; | |
| atmel,lcdcon2 = <0x80008002>; | |
| atmel,guard-time = <1>; | |
| atmel,lcd-wiring-mode = "BRG"; | |
| display-timings { | |
| native-mode = <&timing0>; | |
| timing0: timing0 { | |
| clock-frequency = <4965000>; | |
| hactive = <240>; | |
| vactive = <320>; | |
| hback-porch = <1>; | |
| hfront-porch = <33>; | |
| vback-porch = <1>; | |
| vfront-porch = <0>; | |
| hsync-len = <5>; | |
| vsync-len = <1>; | |
| hsync-active = <1>; | |
| vsync-active = <1>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| ebi: ebi@10000000 { | |
| status = "okay"; | |
| nand_controller: nand-controller { | |
| status = "okay"; | |
| pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; | |
| pinctrl-names = "default"; | |
| nand@3 { | |
| reg = <0x3 0x0 0x800000>; | |
| rb-gpios = <&pioC 15 GPIO_ACTIVE_HIGH>; | |
| cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; | |
| nand-bus-width = <8>; | |
| nand-ecc-mode = "soft"; | |
| nand-on-flash-bbt; | |
| label = "atmel_nand"; | |
| partitions { | |
| compatible = "fixed-partitions"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| at91bootstrap@0 { | |
| label = "at91bootstrap"; | |
| reg = <0x0 0x40000>; | |
| }; | |
| bootloader@40000 { | |
| label = "bootloader"; | |
| reg = <0x40000 0x80000>; | |
| }; | |
| bootloaderenv@c0000 { | |
| label = "bootloader env"; | |
| reg = <0xc0000 0xc0000>; | |
| }; | |
| dtb@180000 { | |
| label = "device tree"; | |
| reg = <0x180000 0x80000>; | |
| }; | |
| kernel@200000 { | |
| label = "kernel"; | |
| reg = <0x200000 0x600000>; | |
| }; | |
| rootfs@800000 { | |
| label = "rootfs"; | |
| reg = <0x800000 0x0f800000>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| }; | |
| apb { | |
| tcb0: timer@fffa0000 { | |
| timer0: timer@0 { | |
| compatible = "atmel,tcb-timer"; | |
| reg = <0>, <1>; | |
| }; | |
| timer1: timer@2 { | |
| compatible = "atmel,tcb-timer"; | |
| reg = <2>; | |
| }; | |
| }; | |
| usb1: gadget@fffa4000 { | |
| atmel,vbus-gpio = <&pioB 29 GPIO_ACTIVE_HIGH>; | |
| status = "okay"; | |
| }; | |
| spi0: spi@fffc8000 { | |
| cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>; | |
| status = "okay"; | |
| flash@0 { | |
| compatible = "atmel,at45", "atmel,dataflash"; | |
| reg = <0>; | |
| spi-max-frequency = <15000000>; | |
| }; | |
| tsc2046@2 { | |
| reg = <2>; | |
| compatible = "ti,ads7843"; | |
| interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>; | |
| spi-max-frequency = <3000000>; | |
| pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>; | |
| ti,x-min = /bits/ 16 <150>; | |
| ti,x-max = /bits/ 16 <3830>; | |
| ti,y-min = /bits/ 16 <190>; | |
| ti,y-max = /bits/ 16 <3830>; | |
| ti,vref-delay-usecs = /bits/ 16 <450>; | |
| ti,x-plate-ohms = /bits/ 16 <450>; | |
| ti,y-plate-ohms = /bits/ 16 <250>; | |
| ti,pressure-max = /bits/ 16 <15000>; | |
| ti,debounce-rep = /bits/ 16 <0>; | |
| ti,debounce-tol = /bits/ 16 <65535>; | |
| ti,debounce-max = /bits/ 16 <1>; | |
| wakeup-source; | |
| }; | |
| }; | |
| dbgu: serial@fffff200 { | |
| status = "okay"; | |
| }; | |
| rtc@fffffd20 { | |
| atmel,rtt-rtc-time-reg = <&gpbr 0x0>; | |
| }; | |
| watchdog@fffffd40 { | |
| status = "okay"; | |
| }; | |
| }; | |
| }; | |
| leds { | |
| compatible = "gpio-leds"; | |
| led-ds8 { | |
| label = "ds8"; | |
| gpios = <&pioA 13 GPIO_ACTIVE_LOW>; | |
| linux,default-trigger = "none"; | |
| }; | |
| led-ds7 { | |
| label = "ds7"; | |
| gpios = <&pioA 14 GPIO_ACTIVE_LOW>; | |
| linux,default-trigger = "nand-disk"; | |
| }; | |
| led-ds1 { | |
| label = "ds1"; | |
| gpios = <&pioA 23 GPIO_ACTIVE_LOW>; | |
| linux,default-trigger = "heartbeat"; | |
| }; | |
| }; | |
| gpio-keys { | |
| compatible = "gpio-keys"; | |
| button-0 { | |
| label = "button_0"; | |
| gpios = <&pioA 27 GPIO_ACTIVE_LOW>; | |
| linux,code = <256>; | |
| wakeup-source; | |
| }; | |
| button-1 { | |
| label = "button_1"; | |
| gpios = <&pioA 26 GPIO_ACTIVE_LOW>; | |
| linux,code = <257>; | |
| wakeup-source; | |
| }; | |
| button-2 { | |
| label = "button_2"; | |
| gpios = <&pioA 25 GPIO_ACTIVE_LOW>; | |
| linux,code = <258>; | |
| wakeup-source; | |
| }; | |
| button-3 { | |
| label = "button_3"; | |
| gpios = <&pioA 24 GPIO_ACTIVE_LOW>; | |
| linux,code = <259>; | |
| wakeup-source; | |
| }; | |
| }; | |
| }; |