| // SPDX-License-Identifier: GPL-2.0 | |
| #include "bcm283x.dtsi" | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> | |
| #include <dt-bindings/soc/bcm2835-pm.h> | |
| / { | |
| compatible = "brcm,bcm2711"; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| interrupt-parent = <&gicv2>; | |
| vc4: gpu { | |
| compatible = "brcm,bcm2711-vc5"; | |
| status = "disabled"; | |
| }; | |
| clk_27MHz: clk-27M { | |
| #clock-cells = <0>; | |
| compatible = "fixed-clock"; | |
| clock-frequency = <27000000>; | |
| clock-output-names = "27MHz-clock"; | |
| }; | |
| clk_108MHz: clk-108M { | |
| #clock-cells = <0>; | |
| compatible = "fixed-clock"; | |
| clock-frequency = <108000000>; | |
| clock-output-names = "108MHz-clock"; | |
| }; | |
| soc { | |
| /* | |
| * Defined ranges: | |
| * Common BCM283x peripherals | |
| * BCM2711-specific peripherals | |
| * ARM-local peripherals | |
| */ | |
| ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, | |
| <0x7c000000 0x0 0xfc000000 0x02000000>, | |
| <0x40000000 0x0 0xff800000 0x00800000>; | |
| /* Emulate a contiguous 30-bit address range for DMA */ | |
| dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; | |
| /* | |
| * This node is the provider for the enable-method for | |
| * bringing up secondary cores. | |
| */ | |
| local_intc: interrupt-controller@40000000 { | |
| compatible = "brcm,bcm2836-l1-intc"; | |
| reg = <0x40000000 0x100>; | |
| }; | |
| gicv2: interrupt-controller@40041000 { | |
| interrupt-controller; | |
| #interrupt-cells = <3>; | |
| compatible = "arm,gic-400"; | |
| reg = <0x40041000 0x1000>, | |
| <0x40042000 0x2000>, | |
| <0x40044000 0x2000>, | |
| <0x40046000 0x2000>; | |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | | |
| IRQ_TYPE_LEVEL_HIGH)>; | |
| }; | |
| avs_monitor: avs-monitor@7d5d2000 { | |
| compatible = "brcm,bcm2711-avs-monitor", | |
| "syscon", "simple-mfd"; | |
| reg = <0x7d5d2000 0xf00>; | |
| thermal: thermal { | |
| compatible = "brcm,bcm2711-thermal"; | |
| #thermal-sensor-cells = <0>; | |
| }; | |
| }; | |
| dma: dma-controller@7e007000 { | |
| compatible = "brcm,bcm2835-dma"; | |
| reg = <0x7e007000 0xb00>; | |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, | |
| /* DMA lite 7 - 10 */ | |
| <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "dma0", | |
| "dma1", | |
| "dma2", | |
| "dma3", | |
| "dma4", | |
| "dma5", | |
| "dma6", | |
| "dma7", | |
| "dma8", | |
| "dma9", | |
| "dma10"; | |
| #dma-cells = <1>; | |
| brcm,dma-channel-mask = <0x07f5>; | |
| }; | |
| pm: watchdog@7e100000 { | |
| compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt"; | |
| #power-domain-cells = <1>; | |
| #reset-cells = <1>; | |
| reg = <0x7e100000 0x114>, | |
| <0x7e00a000 0x24>, | |
| <0x7ec11000 0x20>; | |
| reg-names = "pm", "asb", "rpivid_asb"; | |
| clocks = <&clocks BCM2835_CLOCK_V3D>, | |
| <&clocks BCM2835_CLOCK_PERI_IMAGE>, | |
| <&clocks BCM2835_CLOCK_H264>, | |
| <&clocks BCM2835_CLOCK_ISP>; | |
| clock-names = "v3d", "peri_image", "h264", "isp"; | |
| system-power-controller; | |
| }; | |
| rng@7e104000 { | |
| compatible = "brcm,bcm2711-rng200"; | |
| reg = <0x7e104000 0x28>; | |
| }; | |
| uart2: serial@7e201400 { | |
| compatible = "arm,pl011", "arm,primecell"; | |
| reg = <0x7e201400 0x200>; | |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_UART>, | |
| <&clocks BCM2835_CLOCK_VPU>; | |
| clock-names = "uartclk", "apb_pclk"; | |
| arm,primecell-periphid = <0x00341011>; | |
| status = "disabled"; | |
| }; | |
| uart3: serial@7e201600 { | |
| compatible = "arm,pl011", "arm,primecell"; | |
| reg = <0x7e201600 0x200>; | |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_UART>, | |
| <&clocks BCM2835_CLOCK_VPU>; | |
| clock-names = "uartclk", "apb_pclk"; | |
| arm,primecell-periphid = <0x00341011>; | |
| status = "disabled"; | |
| }; | |
| uart4: serial@7e201800 { | |
| compatible = "arm,pl011", "arm,primecell"; | |
| reg = <0x7e201800 0x200>; | |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_UART>, | |
| <&clocks BCM2835_CLOCK_VPU>; | |
| clock-names = "uartclk", "apb_pclk"; | |
| arm,primecell-periphid = <0x00341011>; | |
| status = "disabled"; | |
| }; | |
| uart5: serial@7e201a00 { | |
| compatible = "arm,pl011", "arm,primecell"; | |
| reg = <0x7e201a00 0x200>; | |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_UART>, | |
| <&clocks BCM2835_CLOCK_VPU>; | |
| clock-names = "uartclk", "apb_pclk"; | |
| arm,primecell-periphid = <0x00341011>; | |
| status = "disabled"; | |
| }; | |
| spi3: spi@7e204600 { | |
| compatible = "brcm,bcm2835-spi"; | |
| reg = <0x7e204600 0x0200>; | |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| spi4: spi@7e204800 { | |
| compatible = "brcm,bcm2835-spi"; | |
| reg = <0x7e204800 0x0200>; | |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| spi5: spi@7e204a00 { | |
| compatible = "brcm,bcm2835-spi"; | |
| reg = <0x7e204a00 0x0200>; | |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| spi6: spi@7e204c00 { | |
| compatible = "brcm,bcm2835-spi"; | |
| reg = <0x7e204c00 0x0200>; | |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| i2c3: i2c@7e205600 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| reg = <0x7e205600 0x200>; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| i2c4: i2c@7e205800 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| reg = <0x7e205800 0x200>; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| i2c5: i2c@7e205a00 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| reg = <0x7e205a00 0x200>; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| i2c6: i2c@7e205c00 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| reg = <0x7e205c00 0x200>; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2835_CLOCK_VPU>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| pixelvalve0: pixelvalve@7e206000 { | |
| compatible = "brcm,bcm2711-pixelvalve0"; | |
| reg = <0x7e206000 0x100>; | |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| pixelvalve1: pixelvalve@7e207000 { | |
| compatible = "brcm,bcm2711-pixelvalve1"; | |
| reg = <0x7e207000 0x100>; | |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| pixelvalve2: pixelvalve@7e20a000 { | |
| compatible = "brcm,bcm2711-pixelvalve2"; | |
| reg = <0x7e20a000 0x100>; | |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| pwm1: pwm@7e20c800 { | |
| compatible = "brcm,bcm2835-pwm"; | |
| reg = <0x7e20c800 0x28>; | |
| clocks = <&clocks BCM2835_CLOCK_PWM>; | |
| assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; | |
| assigned-clock-rates = <10000000>; | |
| #pwm-cells = <3>; | |
| status = "disabled"; | |
| }; | |
| pixelvalve4: pixelvalve@7e216000 { | |
| compatible = "brcm,bcm2711-pixelvalve4"; | |
| reg = <0x7e216000 0x100>; | |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| hvs: hvs@7e400000 { | |
| compatible = "brcm,bcm2711-hvs"; | |
| reg = <0x7e400000 0x8000>; | |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| pixelvalve3: pixelvalve@7ec12000 { | |
| compatible = "brcm,bcm2711-pixelvalve3"; | |
| reg = <0x7ec12000 0x100>; | |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| vec: vec@7ec13000 { | |
| compatible = "brcm,bcm2711-vec"; | |
| reg = <0x7ec13000 0x1000>; | |
| clocks = <&clocks BCM2835_CLOCK_VEC>; | |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| }; | |
| dvp: clock@7ef00000 { | |
| compatible = "brcm,brcm2711-dvp"; | |
| reg = <0x7ef00000 0x10>; | |
| clocks = <&clk_108MHz>; | |
| #clock-cells = <1>; | |
| #reset-cells = <1>; | |
| }; | |
| aon_intr: interrupt-controller@7ef00100 { | |
| compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; | |
| reg = <0x7ef00100 0x30>; | |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| }; | |
| hdmi0: hdmi@7ef00700 { | |
| compatible = "brcm,bcm2711-hdmi0"; | |
| reg = <0x7ef00700 0x300>, | |
| <0x7ef00300 0x200>, | |
| <0x7ef00f00 0x80>, | |
| <0x7ef00f80 0x80>, | |
| <0x7ef01b00 0x200>, | |
| <0x7ef01f00 0x400>, | |
| <0x7ef00200 0x80>, | |
| <0x7ef04300 0x100>, | |
| <0x7ef20000 0x100>; | |
| reg-names = "hdmi", | |
| "dvp", | |
| "phy", | |
| "rm", | |
| "packet", | |
| "metadata", | |
| "csc", | |
| "cec", | |
| "hd"; | |
| clock-names = "hdmi", "bvb", "audio", "cec"; | |
| resets = <&dvp 0>; | |
| interrupt-parent = <&aon_intr>; | |
| interrupts = <0>, <1>, <2>, | |
| <3>, <4>, <5>; | |
| interrupt-names = "cec-tx", "cec-rx", "cec-low", | |
| "wakeup", "hpd-connected", "hpd-removed"; | |
| ddc = <&ddc0>; | |
| dmas = <&dma 10>; | |
| dma-names = "audio-rx"; | |
| status = "disabled"; | |
| }; | |
| ddc0: i2c@7ef04500 { | |
| compatible = "brcm,bcm2711-hdmi-i2c"; | |
| reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; | |
| reg-names = "bsc", "auto-i2c"; | |
| clock-frequency = <97500>; | |
| status = "disabled"; | |
| }; | |
| hdmi1: hdmi@7ef05700 { | |
| compatible = "brcm,bcm2711-hdmi1"; | |
| reg = <0x7ef05700 0x300>, | |
| <0x7ef05300 0x200>, | |
| <0x7ef05f00 0x80>, | |
| <0x7ef05f80 0x80>, | |
| <0x7ef06b00 0x200>, | |
| <0x7ef06f00 0x400>, | |
| <0x7ef00280 0x80>, | |
| <0x7ef09300 0x100>, | |
| <0x7ef20000 0x100>; | |
| reg-names = "hdmi", | |
| "dvp", | |
| "phy", | |
| "rm", | |
| "packet", | |
| "metadata", | |
| "csc", | |
| "cec", | |
| "hd"; | |
| ddc = <&ddc1>; | |
| clock-names = "hdmi", "bvb", "audio", "cec"; | |
| resets = <&dvp 1>; | |
| interrupt-parent = <&aon_intr>; | |
| interrupts = <8>, <7>, <6>, | |
| <9>, <10>, <11>; | |
| interrupt-names = "cec-tx", "cec-rx", "cec-low", | |
| "wakeup", "hpd-connected", "hpd-removed"; | |
| dmas = <&dma 17>; | |
| dma-names = "audio-rx"; | |
| status = "disabled"; | |
| }; | |
| ddc1: i2c@7ef09500 { | |
| compatible = "brcm,bcm2711-hdmi-i2c"; | |
| reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; | |
| reg-names = "bsc", "auto-i2c"; | |
| clock-frequency = <97500>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| /* | |
| * emmc2 has different DMA constraints based on SoC revisions. It was | |
| * moved into its own bus, so as for RPi4's firmware to update them. | |
| * The firmware will find whether the emmc2bus alias is defined, and if | |
| * so, it'll edit the dma-ranges property below accordingly. | |
| */ | |
| emmc2bus: emmc2-bus@fe000000 { | |
| compatible = "simple-bus"; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; | |
| dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; | |
| emmc2: mmc@7e340000 { | |
| compatible = "brcm,bcm2711-emmc2"; | |
| reg = <0x0 0x7e340000 0x100>; | |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clocks BCM2711_CLOCK_EMMC2>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| pmu { | |
| compatible = "arm,cortex-a72-pmu"; | |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; | |
| }; | |
| timer { | |
| compatible = "arm,armv8-timer"; | |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | | |
| IRQ_TYPE_LEVEL_LOW)>, | |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | | |
| IRQ_TYPE_LEVEL_LOW)>, | |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | | |
| IRQ_TYPE_LEVEL_LOW)>, | |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | | |
| IRQ_TYPE_LEVEL_LOW)>; | |
| }; | |
| cpus: cpus { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit | |
| /* Source for d/i-cache-line-size and d/i-cache-sets | |
| * https://developer.arm.com/documentation/100095/0003 | |
| * /Level-1-Memory-System/About-the-L1-memory-system?lang=en | |
| * Source for d/i-cache-size | |
| * https://www.raspberrypi.com/documentation/computers | |
| * /processors.html#bcm2711 | |
| */ | |
| cpu0: cpu@0 { | |
| device_type = "cpu"; | |
| compatible = "arm,cortex-a72"; | |
| reg = <0>; | |
| enable-method = "spin-table"; | |
| cpu-release-addr = <0x0 0x000000d8>; | |
| d-cache-size = <0x8000>; | |
| d-cache-line-size = <64>; | |
| d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set | |
| i-cache-size = <0xc000>; | |
| i-cache-line-size = <64>; | |
| i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set | |
| next-level-cache = <&l2>; | |
| }; | |
| cpu1: cpu@1 { | |
| device_type = "cpu"; | |
| compatible = "arm,cortex-a72"; | |
| reg = <1>; | |
| enable-method = "spin-table"; | |
| cpu-release-addr = <0x0 0x000000e0>; | |
| d-cache-size = <0x8000>; | |
| d-cache-line-size = <64>; | |
| d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set | |
| i-cache-size = <0xc000>; | |
| i-cache-line-size = <64>; | |
| i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set | |
| next-level-cache = <&l2>; | |
| }; | |
| cpu2: cpu@2 { | |
| device_type = "cpu"; | |
| compatible = "arm,cortex-a72"; | |
| reg = <2>; | |
| enable-method = "spin-table"; | |
| cpu-release-addr = <0x0 0x000000e8>; | |
| d-cache-size = <0x8000>; | |
| d-cache-line-size = <64>; | |
| d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set | |
| i-cache-size = <0xc000>; | |
| i-cache-line-size = <64>; | |
| i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set | |
| next-level-cache = <&l2>; | |
| }; | |
| cpu3: cpu@3 { | |
| device_type = "cpu"; | |
| compatible = "arm,cortex-a72"; | |
| reg = <3>; | |
| enable-method = "spin-table"; | |
| cpu-release-addr = <0x0 0x000000f0>; | |
| d-cache-size = <0x8000>; | |
| d-cache-line-size = <64>; | |
| d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set | |
| i-cache-size = <0xc000>; | |
| i-cache-line-size = <64>; | |
| i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set | |
| next-level-cache = <&l2>; | |
| }; | |
| /* Source for d/i-cache-line-size and d/i-cache-sets | |
| * https://developer.arm.com/documentation/100095/0003 | |
| * /Level-2-Memory-System/About-the-L2-memory-system?lang=en | |
| * Source for d/i-cache-size | |
| * https://www.raspberrypi.com/documentation/computers | |
| * /processors.html#bcm2711 | |
| */ | |
| l2: l2-cache0 { | |
| compatible = "cache"; | |
| cache-unified; | |
| cache-size = <0x100000>; | |
| cache-line-size = <64>; | |
| cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set | |
| cache-level = <2>; | |
| }; | |
| }; | |
| scb-bus@fc000000 { | |
| compatible = "simple-bus"; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, | |
| <0x6 0x00000000 0x6 0x00000000 0x40000000>; | |
| pcie0: pcie@7d500000 { | |
| compatible = "brcm,bcm2711-pcie"; | |
| reg = <0x0 0x7d500000 0x9310>; | |
| device_type = "pci"; | |
| #address-cells = <3>; | |
| #interrupt-cells = <1>; | |
| #size-cells = <2>; | |
| interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "pcie", "msi"; | |
| interrupt-map-mask = <0x0 0x0 0x0 0x7>; | |
| interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 | |
| IRQ_TYPE_LEVEL_HIGH>, | |
| <0 0 0 2 &gicv2 GIC_SPI 144 | |
| IRQ_TYPE_LEVEL_HIGH>, | |
| <0 0 0 3 &gicv2 GIC_SPI 145 | |
| IRQ_TYPE_LEVEL_HIGH>, | |
| <0 0 0 4 &gicv2 GIC_SPI 146 | |
| IRQ_TYPE_LEVEL_HIGH>; | |
| msi-controller; | |
| msi-parent = <&pcie0>; | |
| ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 | |
| 0x0 0x04000000>; | |
| /* | |
| * The wrapper around the PCIe block has a bug | |
| * preventing it from accessing beyond the first 3GB of | |
| * memory. | |
| */ | |
| dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 | |
| 0x0 0xc0000000>; | |
| brcm,enable-ssc; | |
| }; | |
| genet: ethernet@7d580000 { | |
| compatible = "brcm,bcm2711-genet-v5"; | |
| reg = <0x0 0x7d580000 0x10000>; | |
| #address-cells = <0x1>; | |
| #size-cells = <0x1>; | |
| interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; | |
| status = "disabled"; | |
| genet_mdio: mdio@e14 { | |
| compatible = "brcm,genet-mdio-v5"; | |
| reg = <0xe14 0x8>; | |
| reg-names = "mdio"; | |
| #address-cells = <0x1>; | |
| #size-cells = <0x0>; | |
| }; | |
| }; | |
| xhci: usb@7e9c0000 { | |
| compatible = "brcm,bcm2711-xhci", "brcm,xhci-brcm-v2"; | |
| reg = <0x0 0x7e9c0000 0x100000>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; | |
| power-domains = <&pm BCM2835_POWER_DOMAIN_USB>; | |
| /* DWC2 and this IP block share the same USB PHY, | |
| * enabling both at the same time results in lockups. | |
| * So keep this node disabled and let the bootloader | |
| * decide which interface should be enabled. | |
| */ | |
| status = "disabled"; | |
| }; | |
| v3d: gpu@7ec00000 { | |
| compatible = "brcm,2711-v3d"; | |
| reg = <0x0 0x7ec00000 0x4000>, | |
| <0x0 0x7ec04000 0x4000>; | |
| reg-names = "hub", "core0"; | |
| power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>; | |
| resets = <&pm BCM2835_RESET_V3D>; | |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| }; | |
| }; | |
| &clk_osc { | |
| clock-frequency = <54000000>; | |
| }; | |
| &clocks { | |
| compatible = "brcm,bcm2711-cprman"; | |
| }; | |
| &cpu_thermal { | |
| coefficients = <(-487) 410040>; | |
| thermal-sensors = <&thermal>; | |
| }; | |
| &dsi0 { | |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &dsi1 { | |
| interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; | |
| compatible = "brcm,bcm2711-dsi1"; | |
| }; | |
| &gpio { | |
| compatible = "brcm,bcm2711-gpio"; | |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; | |
| gpio-ranges = <&gpio 0 0 58>; | |
| gpclk0_gpio49: gpclk0-gpio49 { | |
| pin-gpclk { | |
| pins = "gpio49"; | |
| function = "alt1"; | |
| bias-disable; | |
| }; | |
| }; | |
| gpclk1_gpio50: gpclk1-gpio50 { | |
| pin-gpclk { | |
| pins = "gpio50"; | |
| function = "alt1"; | |
| bias-disable; | |
| }; | |
| }; | |
| gpclk2_gpio51: gpclk2-gpio51 { | |
| pin-gpclk { | |
| pins = "gpio51"; | |
| function = "alt1"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c0_gpio46: i2c0-gpio46 { | |
| pin-sda { | |
| function = "alt0"; | |
| pins = "gpio46"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt0"; | |
| pins = "gpio47"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c1_gpio46: i2c1-gpio46 { | |
| pin-sda { | |
| function = "alt1"; | |
| pins = "gpio46"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt1"; | |
| pins = "gpio47"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c3_gpio2: i2c3-gpio2 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio2"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio3"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c3_gpio4: i2c3-gpio4 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio4"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio5"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c4_gpio6: i2c4-gpio6 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio6"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio7"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c4_gpio8: i2c4-gpio8 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio8"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio9"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c5_gpio10: i2c5-gpio10 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio10"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio11"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c5_gpio12: i2c5-gpio12 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio12"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio13"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c6_gpio0: i2c6-gpio0 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio0"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio1"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c6_gpio22: i2c6-gpio22 { | |
| pin-sda { | |
| function = "alt5"; | |
| pins = "gpio22"; | |
| bias-pull-up; | |
| }; | |
| pin-scl { | |
| function = "alt5"; | |
| pins = "gpio23"; | |
| bias-disable; | |
| }; | |
| }; | |
| i2c_slave_gpio8: i2c-slave-gpio8 { | |
| pins-i2c-slave { | |
| pins = "gpio8", | |
| "gpio9", | |
| "gpio10", | |
| "gpio11"; | |
| function = "alt3"; | |
| }; | |
| }; | |
| jtag_gpio48: jtag-gpio48 { | |
| pins-jtag { | |
| pins = "gpio48", | |
| "gpio49", | |
| "gpio50", | |
| "gpio51", | |
| "gpio52", | |
| "gpio53"; | |
| function = "alt4"; | |
| }; | |
| }; | |
| mii_gpio28: mii-gpio28 { | |
| pins-mii { | |
| pins = "gpio28", | |
| "gpio29", | |
| "gpio30", | |
| "gpio31"; | |
| function = "alt4"; | |
| }; | |
| }; | |
| mii_gpio36: mii-gpio36 { | |
| pins-mii { | |
| pins = "gpio36", | |
| "gpio37", | |
| "gpio38", | |
| "gpio39"; | |
| function = "alt5"; | |
| }; | |
| }; | |
| pcm_gpio50: pcm-gpio50 { | |
| pins-pcm { | |
| pins = "gpio50", | |
| "gpio51", | |
| "gpio52", | |
| "gpio53"; | |
| function = "alt2"; | |
| }; | |
| }; | |
| pwm0_0_gpio12: pwm0-0-gpio12 { | |
| pin-pwm { | |
| pins = "gpio12"; | |
| function = "alt0"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_0_gpio18: pwm0-0-gpio18 { | |
| pin-pwm { | |
| pins = "gpio18"; | |
| function = "alt5"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm1_0_gpio40: pwm1-0-gpio40 { | |
| pin-pwm { | |
| pins = "gpio40"; | |
| function = "alt0"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_1_gpio13: pwm0-1-gpio13 { | |
| pin-pwm { | |
| pins = "gpio13"; | |
| function = "alt0"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_1_gpio19: pwm0-1-gpio19 { | |
| pin-pwm { | |
| pins = "gpio19"; | |
| function = "alt5"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm1_1_gpio41: pwm1-1-gpio41 { | |
| pin-pwm { | |
| pins = "gpio41"; | |
| function = "alt0"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_1_gpio45: pwm0-1-gpio45 { | |
| pin-pwm { | |
| pins = "gpio45"; | |
| function = "alt0"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_0_gpio52: pwm0-0-gpio52 { | |
| pin-pwm { | |
| pins = "gpio52"; | |
| function = "alt1"; | |
| bias-disable; | |
| }; | |
| }; | |
| pwm0_1_gpio53: pwm0-1-gpio53 { | |
| pin-pwm { | |
| pins = "gpio53"; | |
| function = "alt1"; | |
| bias-disable; | |
| }; | |
| }; | |
| rgmii_gpio35: rgmii-gpio35 { | |
| pin-start-stop { | |
| pins = "gpio35"; | |
| function = "alt4"; | |
| }; | |
| pin-rx-ok { | |
| pins = "gpio36"; | |
| function = "alt4"; | |
| }; | |
| }; | |
| rgmii_irq_gpio34: rgmii-irq-gpio34 { | |
| pin-irq { | |
| pins = "gpio34"; | |
| function = "alt5"; | |
| }; | |
| }; | |
| rgmii_irq_gpio39: rgmii-irq-gpio39 { | |
| pin-irq { | |
| pins = "gpio39"; | |
| function = "alt4"; | |
| }; | |
| }; | |
| rgmii_mdio_gpio28: rgmii-mdio-gpio28 { | |
| pins-mdio { | |
| pins = "gpio28", | |
| "gpio29"; | |
| function = "alt5"; | |
| }; | |
| }; | |
| rgmii_mdio_gpio37: rgmii-mdio-gpio37 { | |
| pins-mdio { | |
| pins = "gpio37", | |
| "gpio38"; | |
| function = "alt4"; | |
| }; | |
| }; | |
| spi0_gpio46: spi0-gpio46 { | |
| pins-spi { | |
| pins = "gpio46", | |
| "gpio47", | |
| "gpio48", | |
| "gpio49"; | |
| function = "alt2"; | |
| }; | |
| }; | |
| spi2_gpio46: spi2-gpio46 { | |
| pins-spi { | |
| pins = "gpio46", | |
| "gpio47", | |
| "gpio48", | |
| "gpio49", | |
| "gpio50"; | |
| function = "alt5"; | |
| }; | |
| }; | |
| spi3_gpio0: spi3-gpio0 { | |
| pins-spi { | |
| pins = "gpio0", | |
| "gpio1", | |
| "gpio2", | |
| "gpio3"; | |
| function = "alt3"; | |
| }; | |
| }; | |
| spi4_gpio4: spi4-gpio4 { | |
| pins-spi { | |
| pins = "gpio4", | |
| "gpio5", | |
| "gpio6", | |
| "gpio7"; | |
| function = "alt3"; | |
| }; | |
| }; | |
| spi5_gpio12: spi5-gpio12 { | |
| pins-spi { | |
| pins = "gpio12", | |
| "gpio13", | |
| "gpio14", | |
| "gpio15"; | |
| function = "alt3"; | |
| }; | |
| }; | |
| spi6_gpio18: spi6-gpio18 { | |
| pins-spi { | |
| pins = "gpio18", | |
| "gpio19", | |
| "gpio20", | |
| "gpio21"; | |
| function = "alt3"; | |
| }; | |
| }; | |
| uart2_gpio0: uart2-gpio0 { | |
| pin-tx { | |
| pins = "gpio0"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| pin-rx { | |
| pins = "gpio1"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| }; | |
| uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 { | |
| pin-cts { | |
| pins = "gpio2"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| pin-rts { | |
| pins = "gpio3"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| }; | |
| uart3_gpio4: uart3-gpio4 { | |
| pin-tx { | |
| pins = "gpio4"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| pin-rx { | |
| pins = "gpio5"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| }; | |
| uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 { | |
| pin-cts { | |
| pins = "gpio6"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| pin-rts { | |
| pins = "gpio7"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| }; | |
| uart4_gpio8: uart4-gpio8 { | |
| pin-tx { | |
| pins = "gpio8"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| pin-rx { | |
| pins = "gpio9"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| }; | |
| uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 { | |
| pin-cts { | |
| pins = "gpio10"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| pin-rts { | |
| pins = "gpio11"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| }; | |
| uart5_gpio12: uart5-gpio12 { | |
| pin-tx { | |
| pins = "gpio12"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| pin-rx { | |
| pins = "gpio13"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| }; | |
| uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 { | |
| pin-cts { | |
| pins = "gpio14"; | |
| function = "alt4"; | |
| bias-pull-up; | |
| }; | |
| pin-rts { | |
| pins = "gpio15"; | |
| function = "alt4"; | |
| bias-disable; | |
| }; | |
| }; | |
| }; | |
| &rmem { | |
| #address-cells = <2>; | |
| }; | |
| &csi0 { | |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &csi1 { | |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &cma { | |
| /* | |
| * arm64 reserves the CMA by default somewhere in ZONE_DMA32, | |
| * that's not good enough for the BCM2711 as some devices can | |
| * only address the lower 1G of memory (ZONE_DMA). | |
| */ | |
| alloc-ranges = <0x0 0x00000000 0x40000000>; | |
| }; | |
| &i2c0 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &i2c1 { | |
| compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; | |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &mailbox { | |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &sdhci { | |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &sdhost { | |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &spi { | |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &spi1 { | |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &spi2 { | |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &system_timer { | |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &txp { | |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &uart0 { | |
| arm,primecell-periphid = <0x00341011>; | |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &uart1 { | |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &usb { | |
| interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; | |
| }; | |
| &vec { | |
| compatible = "brcm,bcm2711-vec"; | |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; | |
| }; |