| # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/phy/qcom,dsi-phy-10nm.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: Qualcomm Display DSI 10nm PHY | |
| maintainers: | |
| - Krishna Manikandan <quic_mkrishn@quicinc.com> | |
| allOf: | |
| - $ref: qcom,dsi-phy-common.yaml# | |
| properties: | |
| compatible: | |
| enum: | |
| - qcom,dsi-phy-10nm | |
| - qcom,dsi-phy-10nm-8998 | |
| reg: | |
| items: | |
| - description: dsi phy register set | |
| - description: dsi phy lane register set | |
| - description: dsi pll register set | |
| reg-names: | |
| items: | |
| - const: dsi_phy | |
| - const: dsi_phy_lane | |
| - const: dsi_pll | |
| vdds-supply: | |
| description: | | |
| Connected to DSI0_MIPI_DSI_PLL_VDDA0P9 pin for sc7180 target and | |
| connected to VDDA_MIPI_DSI_0_PLL_0P9 pin for sdm845 target | |
| qcom,phy-rescode-offset-top: | |
| $ref: /schemas/types.yaml#/definitions/int8-array | |
| maxItems: 5 | |
| description: | |
| Integer array of offset for pull-up legs rescode for all five lanes. | |
| To offset the drive strength from the calibrated value in an increasing | |
| manner, -32 is the weakest and +31 is the strongest. | |
| items: | |
| minimum: -32 | |
| maximum: 31 | |
| qcom,phy-rescode-offset-bot: | |
| $ref: /schemas/types.yaml#/definitions/int8-array | |
| maxItems: 5 | |
| description: | |
| Integer array of offset for pull-down legs rescode for all five lanes. | |
| To offset the drive strength from the calibrated value in a decreasing | |
| manner, -32 is the weakest and +31 is the strongest. | |
| items: | |
| minimum: -32 | |
| maximum: 31 | |
| qcom,phy-drive-ldo-level: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | |
| The PHY LDO has an amplitude tuning feature to adjust the LDO output | |
| for the HSTX drive. Use supported levels (mV) to offset the drive level | |
| from the default value. | |
| enum: [ 375, 400, 425, 450, 475, 500 ] | |
| required: | |
| - compatible | |
| - reg | |
| - reg-names | |
| unevaluatedProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/clock/qcom,dispcc-sdm845.h> | |
| #include <dt-bindings/clock/qcom,rpmh.h> | |
| dsi-phy@ae94400 { | |
| compatible = "qcom,dsi-phy-10nm"; | |
| reg = <0x0ae94400 0x200>, | |
| <0x0ae94600 0x280>, | |
| <0x0ae94a00 0x1e0>; | |
| reg-names = "dsi_phy", | |
| "dsi_phy_lane", | |
| "dsi_pll"; | |
| #clock-cells = <1>; | |
| #phy-cells = <0>; | |
| vdds-supply = <&vdda_mipi_dsi0_pll>; | |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, | |
| <&rpmhcc RPMH_CXO_CLK>; | |
| clock-names = "iface", "ref"; | |
| qcom,phy-rescode-offset-top = /bits/ 8 <0 0 0 0 0>; | |
| qcom,phy-rescode-offset-bot = /bits/ 8 <0 0 0 0 0>; | |
| qcom,phy-drive-ldo-level = <400>; | |
| }; | |
| ... |