| # SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) | |
| # Copyright (C) 2019 Texas Instruments Incorporated | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/net/ti,dp83869.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: TI DP83869 ethernet PHY | |
| allOf: | |
| - $ref: ethernet-phy.yaml# | |
| maintainers: | |
| - Andrew Davis <afd@ti.com> | |
| description: | | |
| The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver | |
| with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and | |
| 1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and | |
| 100BASE-FX Fiber protocols. | |
| This device interfaces to the MAC layer through Reduced GMII (RGMII) and | |
| SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode, | |
| the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX | |
| conversions. The DP83869HM can also support Bridge Conversion from RGMII to | |
| SGMII and SGMII to RGMII. | |
| Specifications about the Ethernet PHY can be found at: | |
| http://www.ti.com/lit/ds/symlink/dp83869hm.pdf | |
| properties: | |
| reg: | |
| maxItems: 1 | |
| ti,min-output-impedance: | |
| type: boolean | |
| description: | | |
| MAC Interface Impedance control to set the programmable output impedance | |
| to a minimum value (35 ohms). | |
| ti,max-output-impedance: | |
| type: boolean | |
| description: | | |
| MAC Interface Impedance control to set the programmable output impedance | |
| to a maximum value (70 ohms). | |
| tx-fifo-depth: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values | |
| rx-fifo-depth: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values | |
| ti,clk-output-sel: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values. | |
| ti,op-mode: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Operational mode for the PHY. If this is not set then the operational | |
| mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values | |
| rx-internal-delay-ps: | |
| description: Delay is in pico seconds | |
| enum: [ 250, 500, 750, 1000, 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000, | |
| 3250, 3500, 3750, 4000 ] | |
| default: 2000 | |
| tx-internal-delay-ps: | |
| description: Delay is in pico seconds | |
| enum: [ 250, 500, 750, 1000, 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000, | |
| 3250, 3500, 3750, 4000 ] | |
| default: 2000 | |
| required: | |
| - reg | |
| unevaluatedProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/net/ti-dp83869.h> | |
| mdio0 { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| ethphy0: ethernet-phy@0 { | |
| reg = <0>; | |
| tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>; | |
| rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>; | |
| ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>; | |
| ti,max-output-impedance; | |
| ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>; | |
| rx-internal-delay-ps = <2000>; | |
| tx-internal-delay-ps = <2000>; | |
| }; | |
| }; |