| # SPDX-License-Identifier: GPL-2.0-or-later | |
| # Copyright 2019 IBM Corp. | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: ASPEED SD/SDIO/MMC Controller | |
| maintainers: | |
| - Andrew Jeffery <andrew@aj.id.au> | |
| - Ryan Chen <ryanchen.aspeed@gmail.com> | |
| description: |+ | |
| The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO | |
| Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit data bus if | |
| only a single slot is enabled. | |
| The two slots are supported by a common configuration area. As the SDHCIs for | |
| the slots are dependent on the common configuration area, they are described | |
| as child nodes. | |
| properties: | |
| compatible: | |
| oneOf: | |
| - enum: | |
| - aspeed,ast2400-sd-controller | |
| - aspeed,ast2500-sd-controller | |
| - aspeed,ast2600-sd-controller | |
| - items: | |
| - const: aspeed,ast2700-sd-controller | |
| - const: aspeed,ast2600-sd-controller | |
| reg: | |
| maxItems: 1 | |
| description: Common configuration registers | |
| "#address-cells": | |
| const: 1 | |
| "#size-cells": | |
| const: 1 | |
| ranges: true | |
| clocks: | |
| maxItems: 1 | |
| description: The SD/SDIO controller clock gate | |
| resets: | |
| maxItems: 1 | |
| patternProperties: | |
| "^sdhci@[0-9a-f]+$": | |
| type: object | |
| $ref: sdhci-common.yaml | |
| unevaluatedProperties: false | |
| properties: | |
| compatible: | |
| oneOf: | |
| - enum: | |
| - aspeed,ast2400-sdhci | |
| - aspeed,ast2500-sdhci | |
| - aspeed,ast2600-sdhci | |
| - items: | |
| - const: aspeed,ast2700-sdhci | |
| - const: aspeed,ast2600-sdhci | |
| reg: | |
| maxItems: 1 | |
| description: The SDHCI registers | |
| clocks: | |
| maxItems: 1 | |
| description: The SD bus clock | |
| interrupts: | |
| maxItems: 1 | |
| description: The SD interrupt shared between both slots | |
| sdhci,auto-cmd12: | |
| type: boolean | |
| description: Specifies that controller should use auto CMD12 | |
| required: | |
| - compatible | |
| - reg | |
| - clocks | |
| - interrupts | |
| additionalProperties: false | |
| required: | |
| - compatible | |
| - reg | |
| - "#address-cells" | |
| - "#size-cells" | |
| - ranges | |
| - clocks | |
| if: | |
| properties: | |
| compatible: | |
| contains: | |
| const: aspeed,ast2700-sd-controller | |
| then: | |
| required: | |
| - resets | |
| else: | |
| properties: | |
| resets: false | |
| examples: | |
| - | | |
| #include <dt-bindings/clock/aspeed-clock.h> | |
| sdc@1e740000 { | |
| compatible = "aspeed,ast2500-sd-controller"; | |
| reg = <0x1e740000 0x100>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0 0x1e740000 0x20000>; | |
| clocks = <&syscon ASPEED_CLK_GATE_SDCLK>; | |
| sdhci0: sdhci@100 { | |
| compatible = "aspeed,ast2500-sdhci"; | |
| reg = <0x100 0x100>; | |
| interrupts = <26>; | |
| sdhci,auto-cmd12; | |
| clocks = <&syscon ASPEED_CLK_SDIO>; | |
| }; | |
| sdhci1: sdhci@200 { | |
| compatible = "aspeed,ast2500-sdhci"; | |
| reg = <0x200 0x100>; | |
| interrupts = <26>; | |
| sdhci,auto-cmd12; | |
| clocks = <&syscon ASPEED_CLK_SDIO>; | |
| }; | |
| }; |