| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/media/i2c/samsung,s5kjn1.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Samsung S5KJN1 Image Sensor |
| |
| description: |
| Samsung S5KJN1 (ISOCELL JN1) image sensor is a 50MP image sensor. |
| The sensor is controlled over a serial camera control bus protocol, |
| the widest supported output image frame size is 8160x6144 at 10 frames |
| per second, data output format is RAW10 transferred over 4-lane |
| MIPI D-PHY interface. |
| |
| maintainers: |
| - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> |
| |
| allOf: |
| - $ref: /schemas/media/video-interface-devices.yaml# |
| |
| properties: |
| compatible: |
| const: samsung,s5kjn1 |
| |
| reg: |
| maxItems: 1 |
| |
| clocks: |
| description: MCLK supply clock. |
| maxItems: 1 |
| |
| reset-gpios: |
| description: Active low GPIO connected to RESET pad of the sensor. |
| maxItems: 1 |
| |
| afvdd-supply: |
| description: Autofocus actuator voltage supply, 2.8-3.0 volts. |
| |
| vdda-supply: |
| description: Analogue voltage supply, 2.8 volts. |
| |
| vddd-supply: |
| description: Digital core voltage supply, 1.05 volts. |
| |
| vddio-supply: |
| description: Digital I/O voltage supply, 1.8 volts. |
| |
| port: |
| $ref: /schemas/graph.yaml#/$defs/port-base |
| additionalProperties: false |
| |
| properties: |
| endpoint: |
| $ref: /schemas/media/video-interfaces.yaml# |
| unevaluatedProperties: false |
| |
| properties: |
| data-lanes: |
| items: |
| - const: 1 |
| - const: 2 |
| - const: 3 |
| - const: 4 |
| |
| required: |
| - link-frequencies |
| |
| required: |
| - compatible |
| - reg |
| - port |
| |
| unevaluatedProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/gpio/gpio.h> |
| |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| camera@56 { |
| compatible = "samsung,s5kjn1"; |
| reg = <0x56>; |
| clocks = <&camera_mclk 0>; |
| assigned-clocks = <&camera_mclk 0>; |
| assigned-clock-rates = <24000000>; |
| reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; |
| vdda-supply = <&vreg_2p8>; |
| vddd-supply = <&vreg_1p05>; |
| vddio-supply = <&vreg_1p8>; |
| |
| port { |
| endpoint { |
| link-frequencies = /bits/ 64 <700000000>; |
| remote-endpoint = <&mipi_csi2_ep>; |
| }; |
| }; |
| }; |
| }; |
| ... |
