| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * SDM845 Samsung S9 (SM-G9600) (starqltechn / star2qltechn) common device tree source |
| * |
| * Copyright (c) 2020, The Linux Foundation. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include <dt-bindings/sound/qcom,wcd934x.h> |
| |
| #include "sdm845.dtsi" |
| #include "pm8998.dtsi" |
| #include "sdm845-wcd9340.dtsi" |
| |
| /delete-node/ &rmtfs_mem; |
| /delete-node/ &spss_mem; |
| /delete-node/ &adsp_mem; |
| /delete-node/ &slpi_mem; |
| |
| / { |
| chassis-type = "handset"; |
| model = "Samsung Galaxy S9 SM-G9600"; |
| compatible = "samsung,starqltechn", "qcom,sdm845"; |
| |
| battery: battery { |
| compatible = "simple-battery"; |
| constant-charge-current-max-microamp = <2150000>; |
| charge-full-design-microamp-hours = <3000000>; |
| |
| over-voltage-threshold-microvolt = <4500000>; |
| voltage-min-design-microvolt = <3400000>; |
| voltage-max-design-microvolt = <4350000>; |
| }; |
| |
| chosen { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| framebuffer: framebuffer@9d400000 { |
| compatible = "simple-framebuffer"; |
| reg = <0 0x9d400000 0 (2960 * 1440 * 4)>;//2400000 |
| width = <1440>; |
| height = <2960>; |
| stride = <(1440 * 4)>; |
| format = "a8r8g8b8"; |
| vci-supply = <&s2dos05_ldo4>; |
| vddr-supply = <&s2dos05_buck>; |
| vdd3-supply = <&s2dos05_ldo1>; |
| }; |
| }; |
| |
| slpi_regulator: slpi-regulator { |
| compatible = "regulator-fixed"; |
| pinctrl-0 = <&slpi_ldo_active_state>; |
| pinctrl-names = "default"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "slpi"; |
| |
| enable-active-high; |
| gpio = <&tlmm 8 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vib_regulator: gpio-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "haptic"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| gpio = <&pm8998_gpios 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| regulator-boot-on; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| /* |
| * Apparently RPMh does not provide support for PM8998 S4 because it |
| * is always-on; model it as a fixed regulator. |
| */ |
| vreg_s4a_1p8: pm8998-smps4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_s4a_1p8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| |
| vin-supply = <&vph_pwr>; |
| }; |
| |
| reserved-memory { |
| memory@9d400000 { |
| reg = <0x0 0x9d400000 0x0 0x02400000>; |
| no-map; |
| }; |
| |
| memory@a1300000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xa1300000 0x0 0x100000>; |
| record-size = <0x40000>; |
| console-size = <0x40000>; |
| ftrace-size = <0x40000>; |
| pmsg-size = <0x40000>; |
| }; |
| |
| /* |
| * It seems like reserving the old rmtfs_mem region is also needed to prevent |
| * random crashes which are most likely modem related, more testing needed. |
| */ |
| removed_region: removed-region@88f00000 { |
| reg = <0 0x88f00000 0 0x1c00000>; |
| no-map; |
| }; |
| |
| slpi_mem: slpi@96700000 { |
| reg = <0 0x96700000 0 0x1000000>; |
| no-map; |
| }; |
| |
| spss_mem: spss@97700000 { |
| reg = <0 0x97700000 0 0x100000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@97800000 { |
| reg = <0 0x97800000 0 0x2000000>; |
| no-map; |
| }; |
| |
| rmtfs_mem: rmtfs-mem@fde00000 { |
| compatible = "qcom,rmtfs-mem"; |
| reg = <0 0xfde00000 0 0x202000>; |
| qcom,use-guard-pages; |
| no-map; |
| |
| qcom,client-id = <1>; |
| qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; |
| }; |
| }; |
| |
| i2c-21 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&tlmm 127 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&tlmm 128 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| pinctrl-0 = <&i2c21_sda_state &i2c21_scl_state>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmic@60 { |
| compatible = "samsung,s2dos05"; |
| reg = <0x60>; |
| |
| regulators { |
| s2dos05_ldo1: ldo1 { |
| regulator-active-discharge = <1>; |
| regulator-enable-ramp-delay = <12000>; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-name = "ldo1"; |
| }; |
| |
| s2dos05_ldo2: ldo2 { |
| regulator-active-discharge = <1>; |
| regulator-boot-on; |
| regulator-enable-ramp-delay = <12000>; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "ldo2"; |
| }; |
| |
| s2dos05_ldo3: ldo3 { |
| regulator-active-discharge = <1>; |
| regulator-boot-on; |
| regulator-enable-ramp-delay = <12000>; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-name = "ldo3"; |
| }; |
| |
| s2dos05_ldo4: ldo4 { |
| regulator-active-discharge = <1>; |
| regulator-enable-ramp-delay = <12000>; |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <3775000>; |
| regulator-name = "ldo4"; |
| }; |
| |
| s2dos05_buck: buck { |
| regulator-active-discharge = <1>; |
| regulator-enable-ramp-delay = <12000>; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <2100000>; |
| regulator-name = "buck"; |
| }; |
| }; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| |
| key-vol-up { |
| label = "Volume Up"; |
| gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| }; |
| |
| key-wink { |
| label = "Bixby"; |
| gpios = <&pm8998_gpios 19 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_ENTER>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| vib_pwm: pwm { |
| compatible = "clk-pwm"; |
| #pwm-cells = <2>; |
| assigned-clock-parents = <&rpmhcc RPMH_CXO_CLK>; |
| assigned-clocks = <&gcc GCC_GP1_CLK_SRC>; |
| clocks = <&gcc GCC_GP1_CLK>; |
| pinctrl-0 = <&motor_pwm_default_state>; |
| pinctrl-1 = <&motor_pwm_suspend_state>; |
| pinctrl-names = "default", "suspend"; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sdm845/starqltechn/a630_zap.mbn"; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l26a_1p2>; |
| status = "okay"; |
| |
| panel@0 { |
| compatible = "samsung,s6e3ha8"; |
| reg = <0>; |
| vci-supply = <&s2dos05_ldo4>; |
| vddr-supply = <&s2dos05_buck>; |
| vdd3-supply = <&s2dos05_ldo1>; |
| te-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&dsi_default &dsi_te>; |
| pinctrl-1 = <&dsi_suspend &dsi_te>; |
| pinctrl-names = "default", "suspend"; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| data-lanes = <0 1 2 3>; |
| remote-endpoint = <&panel_in>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vdda_mipi_dsi0_pll>; |
| status = "okay"; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8998-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-s11-supply = <&vph_pwr>; |
| vdd-s12-supply = <&vph_pwr>; |
| vdd-s13-supply = <&vph_pwr>; |
| vdd-l1-l27-supply = <&vreg_s7a_1p025>; |
| vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; |
| vdd-l3-l11-supply = <&vreg_s7a_1p025>; |
| vdd-l4-l5-supply = <&vreg_s7a_1p025>; |
| vdd-l6-supply = <&vph_pwr>; |
| vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; |
| vdd-l26-supply = <&vreg_s3a_1p35>; |
| vin-lvs-1-2-supply = <&vreg_s4a_1p8>; |
| |
| vreg_s2a_1p125: smps2 { |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| vreg_s3a_1p35: smps3 { |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| }; |
| |
| vreg_s5a_2p04: smps5 { |
| regulator-min-microvolt = <1904000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| vreg_s7a_1p025: smps7 { |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1028000>; |
| }; |
| |
| vdd_qusb_hs0: |
| vdda_hp_pcie_core: |
| vdda_mipi_csi0_0p9: |
| vdda_mipi_csi1_0p9: |
| vdda_mipi_csi2_0p9: |
| vdda_mipi_dsi0_pll: |
| vdda_mipi_dsi1_pll: |
| vdda_qlink_lv: |
| vdda_qlink_lv_ck: |
| vdda_qrefs_0p875: |
| vdda_pcie_core: |
| vdda_pll_cc_ebi01: |
| vdda_pll_cc_ebi23: |
| vdda_sp_sensor: |
| vdda_ufs1_core: |
| vdda_ufs2_core: |
| vreg_l1a_0p875: ldo1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_10: |
| vreg_l2a_1p2: ldo2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l3a_1p0: ldo3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdda_usb1_ss_core: |
| vdd_wcss_cx: |
| vdd_wcss_mx: |
| vdda_wcss_pll: |
| vreg_l5a_0p8: ldo5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_13: |
| vreg_l6a_1p8: ldo6 { |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <1856000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a_1p8: ldo7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8a_1p2: ldo8 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1248000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a_1p8: ldo9 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10a_1p8: ldo10 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11a_1p0: ldo11 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1048000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdd_qfprom: |
| vdd_qfprom_sp: |
| vdda_apc1_cs_1p8: |
| vdda_gfx_cs_1p8: |
| vdda_qrefs_1p8: |
| vdda_qusb_hs0_1p8: |
| vddpx_11: |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_2: |
| vreg_l13a_2p95: ldo13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p88: ldo14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15a_1p8: ldo15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2704000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17a_1p3: ldo17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_2p7: ldo18 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19a_3p0: ldo19 { |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <3104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l20a_2p95: ldo20 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l21a_2p95: ldo21 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l22a_2p85: ldo22 { |
| regulator-min-microvolt = <2864000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l23a_3p3: ldo23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdda_qusb_hs0_3p1: |
| vreg_l24a_3p075: ldo24 { |
| regulator-min-microvolt = <3088000>; |
| regulator-max-microvolt = <3088000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l25a_3p3: ldo25 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdda_hp_pcie_1p2: |
| vdda_hv_ebi0: |
| vdda_hv_ebi1: |
| vdda_hv_ebi2: |
| vdda_hv_ebi3: |
| vdda_mipi_csi_1p25: |
| vdda_mipi_dsi0_1p2: |
| vdda_mipi_dsi1_1p2: |
| vdda_pcie_1p2: |
| vdda_ufs1_1p2: |
| vdda_ufs2_1p2: |
| vdda_usb1_ss_1p2: |
| vdda_usb2_ss_1p2: |
| vreg_l26a_1p2: ldo26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l28a_3p0: ldo28 { |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vreg_lvs2a_1p8: lvs2 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8005-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_s3c_0p6: smps3 { |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <600000>; |
| }; |
| }; |
| }; |
| |
| &gcc { |
| protected-clocks = <GCC_QSPI_CORE_CLK>, |
| <GCC_QSPI_CORE_CLK_SRC>, |
| <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, |
| <GCC_LPASS_Q6_AXI_CLK>, |
| <GCC_LPASS_SWAY_CLK>; |
| }; |
| |
| &i2c10 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &gpi_dma1 { |
| status = "okay"; |
| }; |
| |
| &uart9 { |
| status = "okay"; |
| }; |
| |
| &i2c14 { |
| status = "okay"; |
| |
| max77705: pmic@66 { |
| compatible = "maxim,max77705"; |
| reg = <0x66>; |
| #interrupt-cells = <1>; |
| interrupt-parent = <&pm8998_gpios>; |
| interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| pinctrl-0 = <&pmic_int_default>; |
| pinctrl-names = "default"; |
| |
| leds { |
| compatible = "maxim,max77705-rgb"; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| haptic { |
| compatible = "maxim,max77705-haptic"; |
| haptic-supply = <&vib_regulator>; |
| pwms = <&vib_pwm 0 52084>; |
| }; |
| }; |
| |
| max77705_charger: charger@69 { |
| reg = <0x69>; |
| compatible = "maxim,max77705-charger"; |
| monitored-battery = <&battery>; |
| interrupt-parent = <&max77705>; |
| interrupts = <0>; |
| }; |
| |
| fuel-gauge@36 { |
| reg = <0x36>; |
| compatible = "maxim,max77705-battery"; |
| power-supplies = <&max77705_charger>; |
| maxim,rsns-microohm = <5000>; |
| interrupt-parent = <&max77705>; |
| interrupts = <2>; |
| }; |
| }; |
| |
| &ufs_mem_hc { |
| reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; |
| vcc-supply = <&vreg_l20a_2p95>; |
| vcc-max-microamp = <600000>; |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vdda_ufs1_core>; |
| vdda-pll-supply = <&vdda_ufs1_1p2>; |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| pinctrl-0 = <&sdc2_clk_state &sdc2_cmd_state &sdc2_data_state &sd_card_det_n_state>; |
| pinctrl-names = "default"; |
| cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&vreg_l21a_2p95>; |
| vqmmc-supply = <&vddpx_2>; |
| status = "okay"; |
| }; |
| |
| &i2c11 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| touchscreen@48 { |
| compatible = "samsung,s6sy761"; |
| reg = <0x48>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <120 IRQ_TYPE_LEVEL_HIGH>; |
| vdd-supply = <&s2dos05_ldo2>; |
| avdd-supply = <&s2dos05_ldo3>; |
| |
| pinctrl-0 = <&touch_irq_state>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &adsp_pas { |
| firmware-name = "qcom/sdm845/starqltechn/adsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &lpasscc { |
| status = "okay"; |
| }; |
| |
| &sound { |
| compatible = "qcom,sdm845-sndcard"; |
| model = "Samsung Galaxy S9"; |
| pinctrl-0 = <&quat_mi2s_active &quat_mi2s_sd0_active &quat_mi2s_sd1_active>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| audio-routing = "RX_BIAS", "MCLK", |
| "AMIC2", "MIC BIAS2", /* Headset Mic */ |
| "AMIC3", "MIC BIAS2", /* FM radio left Tx */ |
| "AMIC4", "MIC BIAS2", /* FM radio right Tx */ |
| "DMIC0", "MCLK", /* Bottom Mic */ |
| "DMIC0", "MIC BIAS1", |
| "DMIC2", "MCLK", /* Top Mic */ |
| "DMIC2", "MIC BIAS3"; |
| |
| mm1-dai-link { |
| link-name = "MultiMedia1"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| mm2-dai-link { |
| link-name = "MultiMedia2"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| mm3-dai-link { |
| link-name = "MultiMedia3"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| mm4-dai-link { |
| link-name = "MultiMedia4"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>; |
| }; |
| }; |
| |
| mm5-dai-link { |
| link-name = "MultiMedia5"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA5>; |
| }; |
| }; |
| |
| mm6-dai-link { |
| link-name = "MultiMedia6"; |
| |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA6>; |
| }; |
| }; |
| |
| slim-dai-link { |
| link-name = "SLIM Playback 1"; |
| |
| codec { |
| sound-dai = <&wcd9340 AIF1_PB>; |
| }; |
| |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| slimcap-dai-link { |
| link-name = "SLIM Capture 1"; |
| |
| codec { |
| sound-dai = <&wcd9340 AIF1_CAP>; |
| }; |
| |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| slim2-dai-link { |
| link-name = "SLIM Playback 2"; |
| |
| codec { |
| sound-dai = <&wcd9340 AIF2_PB>; |
| }; |
| |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_1_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| slimcap2-dai-link { |
| link-name = "SLIM Capture 2"; |
| |
| codec { |
| sound-dai = <&wcd9340 AIF2_CAP>; |
| }; |
| |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_1_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| slimcap3-dai-link { |
| link-name = "SLIM Capture 3"; |
| |
| codec { |
| sound-dai = <&wcd9340 AIF3_CAP>; |
| }; |
| |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_2_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| }; |
| |
| &q6afedai { |
| dai@22 { |
| reg = <22>; |
| qcom,sd-lines = <1>; |
| }; |
| |
| dai@23 { |
| reg = <23>; |
| qcom,sd-lines = <0>; |
| }; |
| }; |
| |
| &q6asmdai { |
| dai@0 { |
| reg = <0>; |
| }; |
| |
| dai@1 { |
| reg = <1>; |
| }; |
| |
| dai@2 { |
| reg = <2>; |
| }; |
| |
| dai@3 { |
| reg = <3>; |
| }; |
| |
| dai@4 { |
| reg = <4>; |
| }; |
| |
| dai@5 { |
| reg = <5>; |
| }; |
| }; |
| |
| &wcd9340 { |
| reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>; |
| vdd-buck-supply = <&vreg_s4a_1p8>; |
| vdd-buck-sido-supply = <&vreg_s4a_1p8>; |
| vdd-tx-supply = <&vreg_s4a_1p8>; |
| vdd-rx-supply = <&vreg_s4a_1p8>; |
| vdd-io-supply = <&vreg_s4a_1p8>; |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <2700000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| }; |
| |
| &mss_pil { |
| firmware-name = "qcom/sdm845/starqltechn/mba.mbn", |
| "qcom/sdm845/starqltechn/modem.mbn"; |
| status = "okay"; |
| }; |
| |
| &ipa { |
| qcom,gsi-loader = "self"; |
| memory-region = <&ipa_fw_mem>; |
| firmware-name = "qcom/sdm845/starqltechn/ipa_fws.mbn"; |
| status = "okay"; |
| }; |
| |
| &slpi_pas { |
| firmware-name = "qcom/sdm845/starqltechn/slpi.mbn"; |
| cx-supply = <&slpi_regulator>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| /* Until we have Type C hooked up we'll force this as peripheral. */ |
| dr_mode = "peripheral"; |
| }; |
| |
| &usb_1_hsphy { |
| vdd-supply = <&vdda_usb1_ss_core>; |
| vdda-pll-supply = <&vdda_qusb_hs0_1p8>; |
| vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; |
| |
| qcom,imp-res-offset-value = <8>; |
| qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; |
| qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; |
| qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vdda_usb1_ss_1p2>; |
| vdda-pll-supply = <&vdda_usb1_ss_core>; |
| status = "okay"; |
| }; |
| |
| &pm8998_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm8998_gpios { |
| pmic_int_default: pmic-int-default-state { |
| pins = "gpio11"; |
| function = "normal"; |
| input-enable; |
| bias-disable; |
| power-source = <0>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <27 4>, /* SPI (eSE - embedded Secure Element) */ |
| <85 4>; /* SPI (fingerprint reader) */ |
| |
| dsi_default: dsi-default-state { |
| pins = "gpio6"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| dsi_suspend: dsi-suspend-state { |
| pins = "gpio6"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| dsi_te: dsi-te-state { |
| pins = "gpio10"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| i2c21_sda_state: i2c21-sda-state { |
| pins = "gpio127"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c21_scl_state: i2c21-scl-state { |
| pins = "gpio128"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| motor_pwm_default_state: motor-pwm-active-state { |
| pins = "gpio57"; |
| function = "gcc_gp1"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| |
| motor_pwm_suspend_state: motor-pwm-suspend-state { |
| pins = "gpio57"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-low; |
| }; |
| |
| sdc2_clk_state: sdc2-clk-state { |
| pins = "sdc2_clk"; |
| bias-disable; |
| |
| /* |
| * It seems that mmc_test reports errors if drive |
| * strength is not 16 on clk, cmd, and data pins. |
| */ |
| drive-strength = <16>; |
| }; |
| |
| sdc2_cmd_state: sdc2-cmd-state { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <16>; |
| }; |
| |
| sdc2_data_state: sdc2-data-state { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <16>; |
| }; |
| |
| sd_card_det_n_state: sd-card-det-n-state { |
| pins = "gpio126"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| |
| slpi_ldo_active_state: slpi-ldo-active-state { |
| pins = "gpio8"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| touch_irq_state: touch-irq-state { |
| pins = "gpio120"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| |
| &qup_i2c11_default { |
| drive-strength = <2>; |
| bias-disable; |
| }; |
