| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) | |
| # Copyright 2022 Linaro Ltd. | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/pinctrl/semtech,sx1501q.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: Semtech SX150x GPIO expander | |
| maintainers: | |
| - Neil Armstrong <neil.armstrong@linaro.org> | |
| properties: | |
| compatible: | |
| enum: | |
| - semtech,sx1501q | |
| - semtech,sx1502q | |
| - semtech,sx1503q | |
| - semtech,sx1504q | |
| - semtech,sx1505q | |
| - semtech,sx1506q | |
| - semtech,sx1507q | |
| - semtech,sx1508q | |
| - semtech,sx1509q | |
| reg: | |
| maxItems: 1 | |
| gpio-line-names: | |
| minItems: 5 | |
| maxItems: 17 | |
| interrupts: | |
| maxItems: 1 | |
| '#interrupt-cells': | |
| const: 2 | |
| interrupt-controller: true | |
| '#gpio-cells': | |
| const: 2 | |
| gpio-controller: true | |
| semtech,probe-reset: | |
| description: Will trigger a reset of the GPIO expander on probe | |
| type: boolean | |
| patternProperties: | |
| '-cfg$': | |
| type: object | |
| properties: | |
| pins: true | |
| bias-disable: true | |
| bias-pull-up: true | |
| bias-pull-down: true | |
| bias-pull-pin-default: true | |
| drive-push-pull: true | |
| output-low: true | |
| output-high: true | |
| drive-open-drain: true | |
| required: | |
| - pins | |
| allOf: | |
| - $ref: pincfg-node.yaml# | |
| - $ref: pinmux-node.yaml# | |
| - if: | |
| properties: | |
| pins: | |
| contains: | |
| const: oscio | |
| then: | |
| properties: | |
| bias-disable: false | |
| bias-pull-up: false | |
| bias-pull-down: false | |
| bias-pull-pin-default: false | |
| drive-open-drain: false | |
| additionalProperties: false | |
| required: | |
| - compatible | |
| - reg | |
| - '#gpio-cells' | |
| - gpio-controller | |
| allOf: | |
| - $ref: pinctrl.yaml# | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1501q | |
| - semtech,sx1504q | |
| - semtech,sx1507q | |
| then: | |
| properties: | |
| gpio-line-names: | |
| minItems: 5 | |
| maxItems: 5 | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1502q | |
| - semtech,sx1505q | |
| - semtech,sx1508q | |
| then: | |
| properties: | |
| gpio-line-names: | |
| minItems: 9 | |
| maxItems: 9 | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1503q | |
| - semtech,sx1506q | |
| - semtech,sx1509q | |
| then: | |
| properties: | |
| gpio-line-names: | |
| minItems: 17 | |
| maxItems: 17 | |
| - if: | |
| not: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1507q | |
| - semtech,sx1508q | |
| - semtech,sx1509q | |
| then: | |
| properties: | |
| semtech,probe-reset: false | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1501q | |
| - semtech,sx1504q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^gpio[0-3]$' | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1502q | |
| - semtech,sx1505q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^gpio[0-7]$' | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - semtech,sx1503q | |
| - semtech,sx1506q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^(gpio[0-9]|gpio1[0-5])$' | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| const: semtech,sx1507q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^(oscio|gpio[0-3])$' | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| const: semtech,sx1508q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^(oscio|gpio[0-7])$' | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| const: semtech,sx1509q | |
| then: | |
| patternProperties: | |
| '-cfg$': | |
| properties: | |
| pins: | |
| items: | |
| pattern: '^(oscio|gpio[0-9]|gpio1[0-5])$' | |
| additionalProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/interrupt-controller/irq.h> | |
| i2c@1000 { | |
| reg = <0x1000 0x80>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| pinctrl@20 { | |
| compatible = "semtech,sx1501q"; | |
| reg = <0x20>; | |
| #gpio-cells = <2>; | |
| #interrupt-cells = <2>; | |
| interrupts = <16 IRQ_TYPE_EDGE_FALLING>; | |
| gpio-controller; | |
| interrupt-controller; | |
| gpio1-cfg { | |
| pins = "gpio1"; | |
| bias-pull-up; | |
| }; | |
| }; | |
| }; |