| # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/pinctrl/cirrus,madera.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: Cirrus Logic Madera class audio CODECs pinctrl driver | |
| maintainers: | |
| - patches@opensource.cirrus.com | |
| description: | | |
| The Cirrus Logic Madera codecs provide a number of GPIO functions for | |
| interfacing to external hardware and to provide logic outputs to other devices. | |
| Certain groups of GPIO pins also have an alternate function, normally as an | |
| audio interface. | |
| The set of available GPIOs, functions and alternate function groups differs | |
| between CODECs so refer to the datasheet for the CODEC for further information | |
| on what is supported on that device. | |
| The properties for this driver exist within the parent MFD driver node. | |
| See also the core bindings for the parent MFD driver: | |
| Documentation/devicetree/bindings/mfd/cirrus,madera.yaml | |
| And the generic pinmix bindings: | |
| Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | |
| properties: | |
| pin-settings: | |
| description: | |
| One subnode is required to contain the default settings. It | |
| contains an arbitrary number of configuration subnodes, one for | |
| each group or pin configuration you want to apply as a default. | |
| type: object | |
| patternProperties: | |
| '-pins$': | |
| type: object | |
| allOf: | |
| - $ref: pincfg-node.yaml# | |
| - $ref: pinmux-node.yaml# | |
| properties: | |
| groups: | |
| description: | |
| Name of one pin group to configure. | |
| enum: [ aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, | |
| pdmspk2, dmic4, dmic5, dmic6, gpio1, gpio2, gpio3, | |
| gpio4, gpio5, gpio6, gpio7, gpio8, gpio9, | |
| gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, | |
| gpio16, gpio17, gpio18, gpio19, gpio20, gpio21, | |
| gpio22, gpio23, gpio24, gpio25, gpio26, gpio27, | |
| gpio28, gpio29, gpio30, gpio31, gpio32, gpio33, | |
| gpio34, gpio35, gpio36, gpio37, gpio38, gpio39 ] | |
| function: | |
| description: | |
| Name of function to assign to this group. | |
| enum: [ aif1, aif2, aif3, aif4, mif1, mif2, mif3, | |
| pdmspk1, pdmspk2, dmic3, dmic4, dmic5, | |
| dmic6, io, dsp-gpio, irq1, irq2, fll1-clk, | |
| fll1-lock, fll2-clk, fll2-lock, fll3-clk, | |
| fll3-lock, fllao-clk, fllao-lock, opclk, | |
| opclk-async, pwm1, pwm2, spdif, asrc1-in1-lock, | |
| asrc1-in2-lock, asrc2-in1-lock, asrc2-in2-lock, | |
| spkl-short-circuit, spkr-short-circuit, | |
| spk-shutdown, spk-overheat-shutdown, | |
| spk-overheat-warn, timer1-sts, timer2-sts, | |
| timer3-sts, timer4-sts, timer5-sts, timer6-sts, | |
| timer7-sts, timer8-sts, log1-fifo-ne, | |
| log2-fifo-ne, log3-fifo-ne, log4-fifo-ne, | |
| log5-fifo-ne, log6-fifo-ne, log7-fifo-ne, | |
| log8-fifo-ne ] | |
| bias-disable: true | |
| bias-bus-hold: true | |
| bias-pull-up: true | |
| bias-pull-down: true | |
| drive-push-pull: true | |
| drive-open-drain: true | |
| drive-strength: | |
| enum: [ 4, 8 ] | |
| input-schmitt-enable: true | |
| input-schmitt-disable: true | |
| input-debounce: | |
| maxItems: 1 | |
| output-low: true | |
| output-high: true | |
| additionalProperties: false | |
| required: | |
| - groups | |
| additionalProperties: false | |
| required: | |
| - pinctrl-0 | |
| - pinctrl-names | |
| additionalProperties: true |