| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * wm9081.c -- WM9081 ALSA SoC Audio driver | |
| * | |
| * Author: Mark Brown | |
| * | |
| * Copyright 2009-12 Wolfson Microelectronics plc | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/moduleparam.h> | |
| #include <linux/init.h> | |
| #include <linux/delay.h> | |
| #include <linux/device.h> | |
| #include <linux/pm.h> | |
| #include <linux/i2c.h> | |
| #include <linux/regmap.h> | |
| #include <linux/slab.h> | |
| #include <sound/core.h> | |
| #include <sound/pcm.h> | |
| #include <sound/pcm_params.h> | |
| #include <sound/soc.h> | |
| #include <sound/initval.h> | |
| #include <sound/tlv.h> | |
| #include <sound/wm9081.h> | |
| #include "wm9081.h" | |
| static const struct reg_default wm9081_reg[] = { | |
| { 2, 0x00B9 }, /* R2 - Analogue Lineout */ | |
| { 3, 0x00B9 }, /* R3 - Analogue Speaker PGA */ | |
| { 4, 0x0001 }, /* R4 - VMID Control */ | |
| { 5, 0x0068 }, /* R5 - Bias Control 1 */ | |
| { 7, 0x0000 }, /* R7 - Analogue Mixer */ | |
| { 8, 0x0000 }, /* R8 - Anti Pop Control */ | |
| { 9, 0x01DB }, /* R9 - Analogue Speaker 1 */ | |
| { 10, 0x0018 }, /* R10 - Analogue Speaker 2 */ | |
| { 11, 0x0180 }, /* R11 - Power Management */ | |
| { 12, 0x0000 }, /* R12 - Clock Control 1 */ | |
| { 13, 0x0038 }, /* R13 - Clock Control 2 */ | |
| { 14, 0x4000 }, /* R14 - Clock Control 3 */ | |
| { 16, 0x0000 }, /* R16 - FLL Control 1 */ | |
| { 17, 0x0200 }, /* R17 - FLL Control 2 */ | |
| { 18, 0x0000 }, /* R18 - FLL Control 3 */ | |
| { 19, 0x0204 }, /* R19 - FLL Control 4 */ | |
| { 20, 0x0000 }, /* R20 - FLL Control 5 */ | |
| { 22, 0x0000 }, /* R22 - Audio Interface 1 */ | |
| { 23, 0x0002 }, /* R23 - Audio Interface 2 */ | |
| { 24, 0x0008 }, /* R24 - Audio Interface 3 */ | |
| { 25, 0x0022 }, /* R25 - Audio Interface 4 */ | |
| { 27, 0x0006 }, /* R27 - Interrupt Status Mask */ | |
| { 28, 0x0000 }, /* R28 - Interrupt Polarity */ | |
| { 29, 0x0000 }, /* R29 - Interrupt Control */ | |
| { 30, 0x00C0 }, /* R30 - DAC Digital 1 */ | |
| { 31, 0x0008 }, /* R31 - DAC Digital 2 */ | |
| { 32, 0x09AF }, /* R32 - DRC 1 */ | |
| { 33, 0x4201 }, /* R33 - DRC 2 */ | |
| { 34, 0x0000 }, /* R34 - DRC 3 */ | |
| { 35, 0x0000 }, /* R35 - DRC 4 */ | |
| { 38, 0x0000 }, /* R38 - Write Sequencer 1 */ | |
| { 39, 0x0000 }, /* R39 - Write Sequencer 2 */ | |
| { 40, 0x0002 }, /* R40 - MW Slave 1 */ | |
| { 42, 0x0000 }, /* R42 - EQ 1 */ | |
| { 43, 0x0000 }, /* R43 - EQ 2 */ | |
| { 44, 0x0FCA }, /* R44 - EQ 3 */ | |
| { 45, 0x0400 }, /* R45 - EQ 4 */ | |
| { 46, 0x00B8 }, /* R46 - EQ 5 */ | |
| { 47, 0x1EB5 }, /* R47 - EQ 6 */ | |
| { 48, 0xF145 }, /* R48 - EQ 7 */ | |
| { 49, 0x0B75 }, /* R49 - EQ 8 */ | |
| { 50, 0x01C5 }, /* R50 - EQ 9 */ | |
| { 51, 0x169E }, /* R51 - EQ 10 */ | |
| { 52, 0xF829 }, /* R52 - EQ 11 */ | |
| { 53, 0x07AD }, /* R53 - EQ 12 */ | |
| { 54, 0x1103 }, /* R54 - EQ 13 */ | |
| { 55, 0x1C58 }, /* R55 - EQ 14 */ | |
| { 56, 0xF373 }, /* R56 - EQ 15 */ | |
| { 57, 0x0A54 }, /* R57 - EQ 16 */ | |
| { 58, 0x0558 }, /* R58 - EQ 17 */ | |
| { 59, 0x0564 }, /* R59 - EQ 18 */ | |
| { 60, 0x0559 }, /* R60 - EQ 19 */ | |
| { 61, 0x4000 }, /* R61 - EQ 20 */ | |
| }; | |
| static struct { | |
| int ratio; | |
| int clk_sys_rate; | |
| } clk_sys_rates[] = { | |
| { 64, 0 }, | |
| { 128, 1 }, | |
| { 192, 2 }, | |
| { 256, 3 }, | |
| { 384, 4 }, | |
| { 512, 5 }, | |
| { 768, 6 }, | |
| { 1024, 7 }, | |
| { 1408, 8 }, | |
| { 1536, 9 }, | |
| }; | |
| static struct { | |
| int rate; | |
| int sample_rate; | |
| } sample_rates[] = { | |
| { 8000, 0 }, | |
| { 11025, 1 }, | |
| { 12000, 2 }, | |
| { 16000, 3 }, | |
| { 22050, 4 }, | |
| { 24000, 5 }, | |
| { 32000, 6 }, | |
| { 44100, 7 }, | |
| { 48000, 8 }, | |
| { 88200, 9 }, | |
| { 96000, 10 }, | |
| }; | |
| static struct { | |
| int div; /* *10 due to .5s */ | |
| int bclk_div; | |
| } bclk_divs[] = { | |
| { 10, 0 }, | |
| { 15, 1 }, | |
| { 20, 2 }, | |
| { 30, 3 }, | |
| { 40, 4 }, | |
| { 50, 5 }, | |
| { 55, 6 }, | |
| { 60, 7 }, | |
| { 80, 8 }, | |
| { 100, 9 }, | |
| { 110, 10 }, | |
| { 120, 11 }, | |
| { 160, 12 }, | |
| { 200, 13 }, | |
| { 220, 14 }, | |
| { 240, 15 }, | |
| { 250, 16 }, | |
| { 300, 17 }, | |
| { 320, 18 }, | |
| { 440, 19 }, | |
| { 480, 20 }, | |
| }; | |
| struct wm9081_priv { | |
| struct regmap *regmap; | |
| int sysclk_source; | |
| int mclk_rate; | |
| int sysclk_rate; | |
| int fs; | |
| int bclk; | |
| int master; | |
| int fll_fref; | |
| int fll_fout; | |
| int tdm_width; | |
| struct wm9081_pdata pdata; | |
| }; | |
| static bool wm9081_volatile_register(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case WM9081_SOFTWARE_RESET: | |
| case WM9081_INTERRUPT_STATUS: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static bool wm9081_readable_register(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case WM9081_SOFTWARE_RESET: | |
| case WM9081_ANALOGUE_LINEOUT: | |
| case WM9081_ANALOGUE_SPEAKER_PGA: | |
| case WM9081_VMID_CONTROL: | |
| case WM9081_BIAS_CONTROL_1: | |
| case WM9081_ANALOGUE_MIXER: | |
| case WM9081_ANTI_POP_CONTROL: | |
| case WM9081_ANALOGUE_SPEAKER_1: | |
| case WM9081_ANALOGUE_SPEAKER_2: | |
| case WM9081_POWER_MANAGEMENT: | |
| case WM9081_CLOCK_CONTROL_1: | |
| case WM9081_CLOCK_CONTROL_2: | |
| case WM9081_CLOCK_CONTROL_3: | |
| case WM9081_FLL_CONTROL_1: | |
| case WM9081_FLL_CONTROL_2: | |
| case WM9081_FLL_CONTROL_3: | |
| case WM9081_FLL_CONTROL_4: | |
| case WM9081_FLL_CONTROL_5: | |
| case WM9081_AUDIO_INTERFACE_1: | |
| case WM9081_AUDIO_INTERFACE_2: | |
| case WM9081_AUDIO_INTERFACE_3: | |
| case WM9081_AUDIO_INTERFACE_4: | |
| case WM9081_INTERRUPT_STATUS: | |
| case WM9081_INTERRUPT_STATUS_MASK: | |
| case WM9081_INTERRUPT_POLARITY: | |
| case WM9081_INTERRUPT_CONTROL: | |
| case WM9081_DAC_DIGITAL_1: | |
| case WM9081_DAC_DIGITAL_2: | |
| case WM9081_DRC_1: | |
| case WM9081_DRC_2: | |
| case WM9081_DRC_3: | |
| case WM9081_DRC_4: | |
| case WM9081_WRITE_SEQUENCER_1: | |
| case WM9081_WRITE_SEQUENCER_2: | |
| case WM9081_MW_SLAVE_1: | |
| case WM9081_EQ_1: | |
| case WM9081_EQ_2: | |
| case WM9081_EQ_3: | |
| case WM9081_EQ_4: | |
| case WM9081_EQ_5: | |
| case WM9081_EQ_6: | |
| case WM9081_EQ_7: | |
| case WM9081_EQ_8: | |
| case WM9081_EQ_9: | |
| case WM9081_EQ_10: | |
| case WM9081_EQ_11: | |
| case WM9081_EQ_12: | |
| case WM9081_EQ_13: | |
| case WM9081_EQ_14: | |
| case WM9081_EQ_15: | |
| case WM9081_EQ_16: | |
| case WM9081_EQ_17: | |
| case WM9081_EQ_18: | |
| case WM9081_EQ_19: | |
| case WM9081_EQ_20: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static int wm9081_reset(struct regmap *map) | |
| { | |
| return regmap_write(map, WM9081_SOFTWARE_RESET, 0x9081); | |
| } | |
| static const DECLARE_TLV_DB_SCALE(drc_in_tlv, -4500, 75, 0); | |
| static const DECLARE_TLV_DB_SCALE(drc_out_tlv, -2250, 75, 0); | |
| static const DECLARE_TLV_DB_SCALE(drc_min_tlv, -1800, 600, 0); | |
| static const DECLARE_TLV_DB_RANGE(drc_max_tlv, | |
| 0, 0, TLV_DB_SCALE_ITEM(1200, 0, 0), | |
| 1, 1, TLV_DB_SCALE_ITEM(1800, 0, 0), | |
| 2, 2, TLV_DB_SCALE_ITEM(2400, 0, 0), | |
| 3, 3, TLV_DB_SCALE_ITEM(3600, 0, 0) | |
| ); | |
| static const DECLARE_TLV_DB_SCALE(drc_qr_tlv, 1200, 600, 0); | |
| static const DECLARE_TLV_DB_SCALE(drc_startup_tlv, -300, 50, 0); | |
| static const DECLARE_TLV_DB_SCALE(eq_tlv, -1200, 100, 0); | |
| static const DECLARE_TLV_DB_SCALE(in_tlv, -600, 600, 0); | |
| static const DECLARE_TLV_DB_SCALE(dac_tlv, -7200, 75, 1); | |
| static const DECLARE_TLV_DB_SCALE(out_tlv, -5700, 100, 0); | |
| static const char *drc_high_text[] = { | |
| "1", | |
| "1/2", | |
| "1/4", | |
| "1/8", | |
| "1/16", | |
| "0", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(drc_high, WM9081_DRC_3, 3, drc_high_text); | |
| static const char *drc_low_text[] = { | |
| "1", | |
| "1/2", | |
| "1/4", | |
| "1/8", | |
| "0", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(drc_low, WM9081_DRC_3, 0, drc_low_text); | |
| static const char *drc_atk_text[] = { | |
| "181us", | |
| "181us", | |
| "363us", | |
| "726us", | |
| "1.45ms", | |
| "2.9ms", | |
| "5.8ms", | |
| "11.6ms", | |
| "23.2ms", | |
| "46.4ms", | |
| "92.8ms", | |
| "185.6ms", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(drc_atk, WM9081_DRC_2, 12, drc_atk_text); | |
| static const char *drc_dcy_text[] = { | |
| "186ms", | |
| "372ms", | |
| "743ms", | |
| "1.49s", | |
| "2.97s", | |
| "5.94s", | |
| "11.89s", | |
| "23.78s", | |
| "47.56s", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(drc_dcy, WM9081_DRC_2, 8, drc_dcy_text); | |
| static const char *drc_qr_dcy_text[] = { | |
| "0.725ms", | |
| "1.45ms", | |
| "5.8ms", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(drc_qr_dcy, WM9081_DRC_2, 4, drc_qr_dcy_text); | |
| static const char *dac_deemph_text[] = { | |
| "None", | |
| "32kHz", | |
| "44.1kHz", | |
| "48kHz", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(dac_deemph, WM9081_DAC_DIGITAL_2, 1, | |
| dac_deemph_text); | |
| static const char *speaker_mode_text[] = { | |
| "Class D", | |
| "Class AB", | |
| }; | |
| static SOC_ENUM_SINGLE_DECL(speaker_mode, WM9081_ANALOGUE_SPEAKER_2, 6, | |
| speaker_mode_text); | |
| static int speaker_mode_get(struct snd_kcontrol *kcontrol, | |
| struct snd_ctl_elem_value *ucontrol) | |
| { | |
| struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); | |
| unsigned int reg; | |
| reg = snd_soc_component_read(component, WM9081_ANALOGUE_SPEAKER_2); | |
| if (reg & WM9081_SPK_MODE) | |
| ucontrol->value.enumerated.item[0] = 1; | |
| else | |
| ucontrol->value.enumerated.item[0] = 0; | |
| return 0; | |
| } | |
| /* | |
| * Stop any attempts to change speaker mode while the speaker is enabled. | |
| * | |
| * We also have some special anti-pop controls dependent on speaker | |
| * mode which must be changed along with the mode. | |
| */ | |
| static int speaker_mode_put(struct snd_kcontrol *kcontrol, | |
| struct snd_ctl_elem_value *ucontrol) | |
| { | |
| struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); | |
| unsigned int reg_pwr = snd_soc_component_read(component, WM9081_POWER_MANAGEMENT); | |
| unsigned int reg2 = snd_soc_component_read(component, WM9081_ANALOGUE_SPEAKER_2); | |
| /* Are we changing anything? */ | |
| if (ucontrol->value.enumerated.item[0] == | |
| ((reg2 & WM9081_SPK_MODE) != 0)) | |
| return 0; | |
| /* Don't try to change modes while enabled */ | |
| if (reg_pwr & WM9081_SPK_ENA) | |
| return -EINVAL; | |
| if (ucontrol->value.enumerated.item[0]) { | |
| /* Class AB */ | |
| reg2 &= ~(WM9081_SPK_INV_MUTE | WM9081_OUT_SPK_CTRL); | |
| reg2 |= WM9081_SPK_MODE; | |
| } else { | |
| /* Class D */ | |
| reg2 |= WM9081_SPK_INV_MUTE | WM9081_OUT_SPK_CTRL; | |
| reg2 &= ~WM9081_SPK_MODE; | |
| } | |
| snd_soc_component_write(component, WM9081_ANALOGUE_SPEAKER_2, reg2); | |
| return 0; | |
| } | |
| static const struct snd_kcontrol_new wm9081_snd_controls[] = { | |
| SOC_SINGLE_TLV("IN1 Volume", WM9081_ANALOGUE_MIXER, 1, 1, 1, in_tlv), | |
| SOC_SINGLE_TLV("IN2 Volume", WM9081_ANALOGUE_MIXER, 3, 1, 1, in_tlv), | |
| SOC_SINGLE_TLV("Playback Volume", WM9081_DAC_DIGITAL_1, 1, 96, 0, dac_tlv), | |
| SOC_SINGLE("LINEOUT Switch", WM9081_ANALOGUE_LINEOUT, 7, 1, 1), | |
| SOC_SINGLE("LINEOUT ZC Switch", WM9081_ANALOGUE_LINEOUT, 6, 1, 0), | |
| SOC_SINGLE_TLV("LINEOUT Volume", WM9081_ANALOGUE_LINEOUT, 0, 63, 0, out_tlv), | |
| SOC_SINGLE("DRC Switch", WM9081_DRC_1, 15, 1, 0), | |
| SOC_ENUM("DRC High Slope", drc_high), | |
| SOC_ENUM("DRC Low Slope", drc_low), | |
| SOC_SINGLE_TLV("DRC Input Volume", WM9081_DRC_4, 5, 60, 1, drc_in_tlv), | |
| SOC_SINGLE_TLV("DRC Output Volume", WM9081_DRC_4, 0, 30, 1, drc_out_tlv), | |
| SOC_SINGLE_TLV("DRC Minimum Volume", WM9081_DRC_2, 2, 3, 1, drc_min_tlv), | |
| SOC_SINGLE_TLV("DRC Maximum Volume", WM9081_DRC_2, 0, 3, 0, drc_max_tlv), | |
| SOC_ENUM("DRC Attack", drc_atk), | |
| SOC_ENUM("DRC Decay", drc_dcy), | |
| SOC_SINGLE("DRC Quick Release Switch", WM9081_DRC_1, 2, 1, 0), | |
| SOC_SINGLE_TLV("DRC Quick Release Volume", WM9081_DRC_2, 6, 3, 0, drc_qr_tlv), | |
| SOC_ENUM("DRC Quick Release Decay", drc_qr_dcy), | |
| SOC_SINGLE_TLV("DRC Startup Volume", WM9081_DRC_1, 6, 18, 0, drc_startup_tlv), | |
| SOC_SINGLE("EQ Switch", WM9081_EQ_1, 0, 1, 0), | |
| SOC_SINGLE("Speaker DC Volume", WM9081_ANALOGUE_SPEAKER_1, 3, 5, 0), | |
| SOC_SINGLE("Speaker AC Volume", WM9081_ANALOGUE_SPEAKER_1, 0, 5, 0), | |
| SOC_SINGLE("Speaker Switch", WM9081_ANALOGUE_SPEAKER_PGA, 7, 1, 1), | |
| SOC_SINGLE("Speaker ZC Switch", WM9081_ANALOGUE_SPEAKER_PGA, 6, 1, 0), | |
| SOC_SINGLE_TLV("Speaker Volume", WM9081_ANALOGUE_SPEAKER_PGA, 0, 63, 0, | |
| out_tlv), | |
| SOC_ENUM("DAC Deemphasis", dac_deemph), | |
| SOC_ENUM_EXT("Speaker Mode", speaker_mode, speaker_mode_get, speaker_mode_put), | |
| }; | |
| static const struct snd_kcontrol_new wm9081_eq_controls[] = { | |
| SOC_SINGLE_TLV("EQ1 Volume", WM9081_EQ_1, 11, 24, 0, eq_tlv), | |
| SOC_SINGLE_TLV("EQ2 Volume", WM9081_EQ_1, 6, 24, 0, eq_tlv), | |
| SOC_SINGLE_TLV("EQ3 Volume", WM9081_EQ_1, 1, 24, 0, eq_tlv), | |
| SOC_SINGLE_TLV("EQ4 Volume", WM9081_EQ_2, 11, 24, 0, eq_tlv), | |
| SOC_SINGLE_TLV("EQ5 Volume", WM9081_EQ_2, 6, 24, 0, eq_tlv), | |
| }; | |
| static const struct snd_kcontrol_new mixer[] = { | |
| SOC_DAPM_SINGLE("IN1 Switch", WM9081_ANALOGUE_MIXER, 0, 1, 0), | |
| SOC_DAPM_SINGLE("IN2 Switch", WM9081_ANALOGUE_MIXER, 2, 1, 0), | |
| SOC_DAPM_SINGLE("Playback Switch", WM9081_ANALOGUE_MIXER, 4, 1, 0), | |
| }; | |
| struct _fll_div { | |
| u16 fll_fratio; | |
| u16 fll_outdiv; | |
| u16 fll_clk_ref_div; | |
| u16 n; | |
| u16 k; | |
| }; | |
| /* The size in bits of the FLL divide multiplied by 10 | |
| * to allow rounding later */ | |
| #define FIXED_FLL_SIZE ((1 << 16) * 10) | |
| static struct { | |
| unsigned int min; | |
| unsigned int max; | |
| u16 fll_fratio; | |
| int ratio; | |
| } fll_fratios[] = { | |
| { 0, 64000, 4, 16 }, | |
| { 64000, 128000, 3, 8 }, | |
| { 128000, 256000, 2, 4 }, | |
| { 256000, 1000000, 1, 2 }, | |
| { 1000000, 13500000, 0, 1 }, | |
| }; | |
| static int fll_factors(struct _fll_div *fll_div, unsigned int Fref, | |
| unsigned int Fout) | |
| { | |
| u64 Kpart; | |
| unsigned int K, Ndiv, Nmod, target; | |
| unsigned int div; | |
| int i; | |
| /* Fref must be <=13.5MHz */ | |
| div = 1; | |
| while ((Fref / div) > 13500000) { | |
| div *= 2; | |
| if (div > 8) { | |
| pr_err("Can't scale %dMHz input down to <=13.5MHz\n", | |
| Fref); | |
| return -EINVAL; | |
| } | |
| } | |
| fll_div->fll_clk_ref_div = div / 2; | |
| pr_debug("Fref=%u Fout=%u\n", Fref, Fout); | |
| /* Apply the division for our remaining calculations */ | |
| Fref /= div; | |
| /* Fvco should be 90-100MHz; don't check the upper bound */ | |
| div = 0; | |
| target = Fout * 2; | |
| while (target < 90000000) { | |
| div++; | |
| target *= 2; | |
| if (div > 7) { | |
| pr_err("Unable to find FLL_OUTDIV for Fout=%uHz\n", | |
| Fout); | |
| return -EINVAL; | |
| } | |
| } | |
| fll_div->fll_outdiv = div; | |
| pr_debug("Fvco=%dHz\n", target); | |
| /* Find an appropriate FLL_FRATIO and factor it out of the target */ | |
| for (i = 0; i < ARRAY_SIZE(fll_fratios); i++) { | |
| if (fll_fratios[i].min <= Fref && Fref <= fll_fratios[i].max) { | |
| fll_div->fll_fratio = fll_fratios[i].fll_fratio; | |
| target /= fll_fratios[i].ratio; | |
| break; | |
| } | |
| } | |
| if (i == ARRAY_SIZE(fll_fratios)) { | |
| pr_err("Unable to find FLL_FRATIO for Fref=%uHz\n", Fref); | |
| return -EINVAL; | |
| } | |
| /* Now, calculate N.K */ | |
| Ndiv = target / Fref; | |
| fll_div->n = Ndiv; | |
| Nmod = target % Fref; | |
| pr_debug("Nmod=%d\n", Nmod); | |
| /* Calculate fractional part - scale up so we can round. */ | |
| Kpart = FIXED_FLL_SIZE * (long long)Nmod; | |
| do_div(Kpart, Fref); | |
| K = Kpart & 0xFFFFFFFF; | |
| if ((K % 10) >= 5) | |
| K += 5; | |
| /* Move down to proper range now rounding is done */ | |
| fll_div->k = K / 10; | |
| pr_debug("N=%x K=%x FLL_FRATIO=%x FLL_OUTDIV=%x FLL_CLK_REF_DIV=%x\n", | |
| fll_div->n, fll_div->k, | |
| fll_div->fll_fratio, fll_div->fll_outdiv, | |
| fll_div->fll_clk_ref_div); | |
| return 0; | |
| } | |
| static int wm9081_set_fll(struct snd_soc_component *component, int fll_id, | |
| unsigned int Fref, unsigned int Fout) | |
| { | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| u16 reg1, reg4, reg5; | |
| struct _fll_div fll_div; | |
| int ret; | |
| int clk_sys_reg; | |
| /* Any change? */ | |
| if (Fref == wm9081->fll_fref && Fout == wm9081->fll_fout) | |
| return 0; | |
| /* Disable the FLL */ | |
| if (Fout == 0) { | |
| dev_dbg(component->dev, "FLL disabled\n"); | |
| wm9081->fll_fref = 0; | |
| wm9081->fll_fout = 0; | |
| return 0; | |
| } | |
| ret = fll_factors(&fll_div, Fref, Fout); | |
| if (ret != 0) | |
| return ret; | |
| reg5 = snd_soc_component_read(component, WM9081_FLL_CONTROL_5); | |
| reg5 &= ~WM9081_FLL_CLK_SRC_MASK; | |
| switch (fll_id) { | |
| case WM9081_SYSCLK_FLL_MCLK: | |
| reg5 |= 0x1; | |
| break; | |
| default: | |
| dev_err(component->dev, "Unknown FLL ID %d\n", fll_id); | |
| return -EINVAL; | |
| } | |
| /* Disable CLK_SYS while we reconfigure */ | |
| clk_sys_reg = snd_soc_component_read(component, WM9081_CLOCK_CONTROL_3); | |
| if (clk_sys_reg & WM9081_CLK_SYS_ENA) | |
| snd_soc_component_write(component, WM9081_CLOCK_CONTROL_3, | |
| clk_sys_reg & ~WM9081_CLK_SYS_ENA); | |
| /* Any FLL configuration change requires that the FLL be | |
| * disabled first. */ | |
| reg1 = snd_soc_component_read(component, WM9081_FLL_CONTROL_1); | |
| reg1 &= ~WM9081_FLL_ENA; | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_1, reg1); | |
| /* Apply the configuration */ | |
| if (fll_div.k) | |
| reg1 |= WM9081_FLL_FRAC_MASK; | |
| else | |
| reg1 &= ~WM9081_FLL_FRAC_MASK; | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_1, reg1); | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_2, | |
| (fll_div.fll_outdiv << WM9081_FLL_OUTDIV_SHIFT) | | |
| (fll_div.fll_fratio << WM9081_FLL_FRATIO_SHIFT)); | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_3, fll_div.k); | |
| reg4 = snd_soc_component_read(component, WM9081_FLL_CONTROL_4); | |
| reg4 &= ~WM9081_FLL_N_MASK; | |
| reg4 |= fll_div.n << WM9081_FLL_N_SHIFT; | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_4, reg4); | |
| reg5 &= ~WM9081_FLL_CLK_REF_DIV_MASK; | |
| reg5 |= fll_div.fll_clk_ref_div << WM9081_FLL_CLK_REF_DIV_SHIFT; | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_5, reg5); | |
| /* Set gain to the recommended value */ | |
| snd_soc_component_update_bits(component, WM9081_FLL_CONTROL_4, | |
| WM9081_FLL_GAIN_MASK, 0); | |
| /* Enable the FLL */ | |
| snd_soc_component_write(component, WM9081_FLL_CONTROL_1, reg1 | WM9081_FLL_ENA); | |
| /* Then bring CLK_SYS up again if it was disabled */ | |
| if (clk_sys_reg & WM9081_CLK_SYS_ENA) | |
| snd_soc_component_write(component, WM9081_CLOCK_CONTROL_3, clk_sys_reg); | |
| dev_dbg(component->dev, "FLL enabled at %dHz->%dHz\n", Fref, Fout); | |
| wm9081->fll_fref = Fref; | |
| wm9081->fll_fout = Fout; | |
| return 0; | |
| } | |
| static int configure_clock(struct snd_soc_component *component) | |
| { | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| int new_sysclk, i, target; | |
| unsigned int reg; | |
| int ret = 0; | |
| int mclkdiv = 0; | |
| int fll = 0; | |
| switch (wm9081->sysclk_source) { | |
| case WM9081_SYSCLK_MCLK: | |
| if (wm9081->mclk_rate > 12225000) { | |
| mclkdiv = 1; | |
| wm9081->sysclk_rate = wm9081->mclk_rate / 2; | |
| } else { | |
| wm9081->sysclk_rate = wm9081->mclk_rate; | |
| } | |
| wm9081_set_fll(component, WM9081_SYSCLK_FLL_MCLK, 0, 0); | |
| break; | |
| case WM9081_SYSCLK_FLL_MCLK: | |
| /* If we have a sample rate calculate a CLK_SYS that | |
| * gives us a suitable DAC configuration, plus BCLK. | |
| * Ideally we would check to see if we can clock | |
| * directly from MCLK and only use the FLL if this is | |
| * not the case, though care must be taken with free | |
| * running mode. | |
| */ | |
| if (wm9081->master && wm9081->bclk) { | |
| /* Make sure we can generate CLK_SYS and BCLK | |
| * and that we've got 3MHz for optimal | |
| * performance. */ | |
| for (i = 0; i < ARRAY_SIZE(clk_sys_rates); i++) { | |
| target = wm9081->fs * clk_sys_rates[i].ratio; | |
| new_sysclk = target; | |
| if (target >= wm9081->bclk && | |
| target > 3000000) | |
| break; | |
| } | |
| if (i == ARRAY_SIZE(clk_sys_rates)) | |
| return -EINVAL; | |
| } else if (wm9081->fs) { | |
| for (i = 0; i < ARRAY_SIZE(clk_sys_rates); i++) { | |
| new_sysclk = clk_sys_rates[i].ratio | |
| * wm9081->fs; | |
| if (new_sysclk > 3000000) | |
| break; | |
| } | |
| if (i == ARRAY_SIZE(clk_sys_rates)) | |
| return -EINVAL; | |
| } else { | |
| new_sysclk = 12288000; | |
| } | |
| ret = wm9081_set_fll(component, WM9081_SYSCLK_FLL_MCLK, | |
| wm9081->mclk_rate, new_sysclk); | |
| if (ret == 0) { | |
| wm9081->sysclk_rate = new_sysclk; | |
| /* Switch SYSCLK over to FLL */ | |
| fll = 1; | |
| } else { | |
| wm9081->sysclk_rate = wm9081->mclk_rate; | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| reg = snd_soc_component_read(component, WM9081_CLOCK_CONTROL_1); | |
| if (mclkdiv) | |
| reg |= WM9081_MCLKDIV2; | |
| else | |
| reg &= ~WM9081_MCLKDIV2; | |
| snd_soc_component_write(component, WM9081_CLOCK_CONTROL_1, reg); | |
| reg = snd_soc_component_read(component, WM9081_CLOCK_CONTROL_3); | |
| if (fll) | |
| reg |= WM9081_CLK_SRC_SEL; | |
| else | |
| reg &= ~WM9081_CLK_SRC_SEL; | |
| snd_soc_component_write(component, WM9081_CLOCK_CONTROL_3, reg); | |
| dev_dbg(component->dev, "CLK_SYS is %dHz\n", wm9081->sysclk_rate); | |
| return ret; | |
| } | |
| static int clk_sys_event(struct snd_soc_dapm_widget *w, | |
| struct snd_kcontrol *kcontrol, int event) | |
| { | |
| struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm); | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| /* This should be done on init() for bypass paths */ | |
| switch (wm9081->sysclk_source) { | |
| case WM9081_SYSCLK_MCLK: | |
| dev_dbg(component->dev, "Using %dHz MCLK\n", wm9081->mclk_rate); | |
| break; | |
| case WM9081_SYSCLK_FLL_MCLK: | |
| dev_dbg(component->dev, "Using %dHz MCLK with FLL\n", | |
| wm9081->mclk_rate); | |
| break; | |
| default: | |
| dev_err(component->dev, "System clock not configured\n"); | |
| return -EINVAL; | |
| } | |
| switch (event) { | |
| case SND_SOC_DAPM_PRE_PMU: | |
| configure_clock(component); | |
| break; | |
| case SND_SOC_DAPM_POST_PMD: | |
| /* Disable the FLL if it's running */ | |
| wm9081_set_fll(component, 0, 0, 0); | |
| break; | |
| } | |
| return 0; | |
| } | |
| static const struct snd_soc_dapm_widget wm9081_dapm_widgets[] = { | |
| SND_SOC_DAPM_INPUT("IN1"), | |
| SND_SOC_DAPM_INPUT("IN2"), | |
| SND_SOC_DAPM_DAC("DAC", NULL, WM9081_POWER_MANAGEMENT, 0, 0), | |
| SND_SOC_DAPM_MIXER_NAMED_CTL("Mixer", SND_SOC_NOPM, 0, 0, | |
| mixer, ARRAY_SIZE(mixer)), | |
| SND_SOC_DAPM_PGA("LINEOUT PGA", WM9081_POWER_MANAGEMENT, 4, 0, NULL, 0), | |
| SND_SOC_DAPM_PGA("Speaker PGA", WM9081_POWER_MANAGEMENT, 2, 0, NULL, 0), | |
| SND_SOC_DAPM_OUT_DRV("Speaker", WM9081_POWER_MANAGEMENT, 1, 0, NULL, 0), | |
| SND_SOC_DAPM_OUTPUT("LINEOUT"), | |
| SND_SOC_DAPM_OUTPUT("SPKN"), | |
| SND_SOC_DAPM_OUTPUT("SPKP"), | |
| SND_SOC_DAPM_SUPPLY("CLK_SYS", WM9081_CLOCK_CONTROL_3, 0, 0, clk_sys_event, | |
| SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD), | |
| SND_SOC_DAPM_SUPPLY("CLK_DSP", WM9081_CLOCK_CONTROL_3, 1, 0, NULL, 0), | |
| SND_SOC_DAPM_SUPPLY("TOCLK", WM9081_CLOCK_CONTROL_3, 2, 0, NULL, 0), | |
| SND_SOC_DAPM_SUPPLY("TSENSE", WM9081_POWER_MANAGEMENT, 7, 0, NULL, 0), | |
| }; | |
| static const struct snd_soc_dapm_route wm9081_audio_paths[] = { | |
| { "DAC", NULL, "CLK_SYS" }, | |
| { "DAC", NULL, "CLK_DSP" }, | |
| { "DAC", NULL, "AIF" }, | |
| { "Mixer", "IN1 Switch", "IN1" }, | |
| { "Mixer", "IN2 Switch", "IN2" }, | |
| { "Mixer", "Playback Switch", "DAC" }, | |
| { "LINEOUT PGA", NULL, "Mixer" }, | |
| { "LINEOUT PGA", NULL, "TOCLK" }, | |
| { "LINEOUT PGA", NULL, "CLK_SYS" }, | |
| { "LINEOUT", NULL, "LINEOUT PGA" }, | |
| { "Speaker PGA", NULL, "Mixer" }, | |
| { "Speaker PGA", NULL, "TOCLK" }, | |
| { "Speaker PGA", NULL, "CLK_SYS" }, | |
| { "Speaker", NULL, "Speaker PGA" }, | |
| { "Speaker", NULL, "TSENSE" }, | |
| { "SPKN", NULL, "Speaker" }, | |
| { "SPKP", NULL, "Speaker" }, | |
| }; | |
| static int wm9081_set_bias_level(struct snd_soc_component *component, | |
| enum snd_soc_bias_level level) | |
| { | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| struct snd_soc_dapm_context *dapm = snd_soc_component_to_dapm(component); | |
| switch (level) { | |
| case SND_SOC_BIAS_ON: | |
| break; | |
| case SND_SOC_BIAS_PREPARE: | |
| /* VMID=2*40k */ | |
| snd_soc_component_update_bits(component, WM9081_VMID_CONTROL, | |
| WM9081_VMID_SEL_MASK, 0x2); | |
| /* Normal bias current */ | |
| snd_soc_component_update_bits(component, WM9081_BIAS_CONTROL_1, | |
| WM9081_STBY_BIAS_ENA, 0); | |
| break; | |
| case SND_SOC_BIAS_STANDBY: | |
| /* Initial cold start */ | |
| if (snd_soc_dapm_get_bias_level(dapm) == SND_SOC_BIAS_OFF) { | |
| regcache_cache_only(wm9081->regmap, false); | |
| regcache_sync(wm9081->regmap); | |
| /* Disable LINEOUT discharge */ | |
| snd_soc_component_update_bits(component, WM9081_ANTI_POP_CONTROL, | |
| WM9081_LINEOUT_DISCH, 0); | |
| /* Select startup bias source */ | |
| snd_soc_component_update_bits(component, WM9081_BIAS_CONTROL_1, | |
| WM9081_BIAS_SRC | WM9081_BIAS_ENA, | |
| WM9081_BIAS_SRC | WM9081_BIAS_ENA); | |
| /* VMID 2*4k; Soft VMID ramp enable */ | |
| snd_soc_component_update_bits(component, WM9081_VMID_CONTROL, | |
| WM9081_VMID_RAMP | | |
| WM9081_VMID_SEL_MASK, | |
| WM9081_VMID_RAMP | 0x6); | |
| mdelay(100); | |
| /* Normal bias enable & soft start off */ | |
| snd_soc_component_update_bits(component, WM9081_VMID_CONTROL, | |
| WM9081_VMID_RAMP, 0); | |
| /* Standard bias source */ | |
| snd_soc_component_update_bits(component, WM9081_BIAS_CONTROL_1, | |
| WM9081_BIAS_SRC, 0); | |
| } | |
| /* VMID 2*240k */ | |
| snd_soc_component_update_bits(component, WM9081_VMID_CONTROL, | |
| WM9081_VMID_SEL_MASK, 0x04); | |
| /* Standby bias current on */ | |
| snd_soc_component_update_bits(component, WM9081_BIAS_CONTROL_1, | |
| WM9081_STBY_BIAS_ENA, | |
| WM9081_STBY_BIAS_ENA); | |
| break; | |
| case SND_SOC_BIAS_OFF: | |
| /* Startup bias source and disable bias */ | |
| snd_soc_component_update_bits(component, WM9081_BIAS_CONTROL_1, | |
| WM9081_BIAS_SRC | WM9081_BIAS_ENA, | |
| WM9081_BIAS_SRC); | |
| /* Disable VMID with soft ramping */ | |
| snd_soc_component_update_bits(component, WM9081_VMID_CONTROL, | |
| WM9081_VMID_RAMP | WM9081_VMID_SEL_MASK, | |
| WM9081_VMID_RAMP); | |
| /* Actively discharge LINEOUT */ | |
| snd_soc_component_update_bits(component, WM9081_ANTI_POP_CONTROL, | |
| WM9081_LINEOUT_DISCH, | |
| WM9081_LINEOUT_DISCH); | |
| regcache_cache_only(wm9081->regmap, true); | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int wm9081_set_dai_fmt(struct snd_soc_dai *dai, | |
| unsigned int fmt) | |
| { | |
| struct snd_soc_component *component = dai->component; | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| unsigned int aif2 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_2); | |
| aif2 &= ~(WM9081_AIF_BCLK_INV | WM9081_AIF_LRCLK_INV | | |
| WM9081_BCLK_DIR | WM9081_LRCLK_DIR | WM9081_AIF_FMT_MASK); | |
| switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { | |
| case SND_SOC_DAIFMT_CBC_CFC: | |
| wm9081->master = 0; | |
| break; | |
| case SND_SOC_DAIFMT_CBC_CFP: | |
| aif2 |= WM9081_LRCLK_DIR; | |
| wm9081->master = 1; | |
| break; | |
| case SND_SOC_DAIFMT_CBP_CFC: | |
| aif2 |= WM9081_BCLK_DIR; | |
| wm9081->master = 1; | |
| break; | |
| case SND_SOC_DAIFMT_CBP_CFP: | |
| aif2 |= WM9081_LRCLK_DIR | WM9081_BCLK_DIR; | |
| wm9081->master = 1; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_DSP_B: | |
| aif2 |= WM9081_AIF_LRCLK_INV; | |
| fallthrough; | |
| case SND_SOC_DAIFMT_DSP_A: | |
| aif2 |= 0x3; | |
| break; | |
| case SND_SOC_DAIFMT_I2S: | |
| aif2 |= 0x2; | |
| break; | |
| case SND_SOC_DAIFMT_RIGHT_J: | |
| break; | |
| case SND_SOC_DAIFMT_LEFT_J: | |
| aif2 |= 0x1; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_DSP_A: | |
| case SND_SOC_DAIFMT_DSP_B: | |
| /* frame inversion not valid for DSP modes */ | |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { | |
| case SND_SOC_DAIFMT_NB_NF: | |
| break; | |
| case SND_SOC_DAIFMT_IB_NF: | |
| aif2 |= WM9081_AIF_BCLK_INV; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| break; | |
| case SND_SOC_DAIFMT_I2S: | |
| case SND_SOC_DAIFMT_RIGHT_J: | |
| case SND_SOC_DAIFMT_LEFT_J: | |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { | |
| case SND_SOC_DAIFMT_NB_NF: | |
| break; | |
| case SND_SOC_DAIFMT_IB_IF: | |
| aif2 |= WM9081_AIF_BCLK_INV | WM9081_AIF_LRCLK_INV; | |
| break; | |
| case SND_SOC_DAIFMT_IB_NF: | |
| aif2 |= WM9081_AIF_BCLK_INV; | |
| break; | |
| case SND_SOC_DAIFMT_NB_IF: | |
| aif2 |= WM9081_AIF_LRCLK_INV; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| snd_soc_component_write(component, WM9081_AUDIO_INTERFACE_2, aif2); | |
| return 0; | |
| } | |
| static int wm9081_hw_params(struct snd_pcm_substream *substream, | |
| struct snd_pcm_hw_params *params, | |
| struct snd_soc_dai *dai) | |
| { | |
| struct snd_soc_component *component = dai->component; | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| int ret, i, best, best_val, cur_val; | |
| unsigned int clk_ctrl2, aif1, aif2, aif3, aif4; | |
| clk_ctrl2 = snd_soc_component_read(component, WM9081_CLOCK_CONTROL_2); | |
| clk_ctrl2 &= ~(WM9081_CLK_SYS_RATE_MASK | WM9081_SAMPLE_RATE_MASK); | |
| aif1 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_1); | |
| aif2 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_2); | |
| aif2 &= ~WM9081_AIF_WL_MASK; | |
| aif3 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_3); | |
| aif3 &= ~WM9081_BCLK_DIV_MASK; | |
| aif4 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_4); | |
| aif4 &= ~WM9081_LRCLK_RATE_MASK; | |
| wm9081->fs = params_rate(params); | |
| if (wm9081->tdm_width) { | |
| /* If TDM is set up then that fixes our BCLK. */ | |
| int slots = ((aif1 & WM9081_AIFDAC_TDM_MODE_MASK) >> | |
| WM9081_AIFDAC_TDM_MODE_SHIFT) + 1; | |
| wm9081->bclk = wm9081->fs * wm9081->tdm_width * slots; | |
| } else { | |
| /* Otherwise work out a BCLK from the sample size */ | |
| wm9081->bclk = 2 * wm9081->fs; | |
| switch (params_width(params)) { | |
| case 16: | |
| wm9081->bclk *= 16; | |
| break; | |
| case 20: | |
| wm9081->bclk *= 20; | |
| aif2 |= 0x4; | |
| break; | |
| case 24: | |
| wm9081->bclk *= 24; | |
| aif2 |= 0x8; | |
| break; | |
| case 32: | |
| wm9081->bclk *= 32; | |
| aif2 |= 0xc; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| dev_dbg(component->dev, "Target BCLK is %dHz\n", wm9081->bclk); | |
| ret = configure_clock(component); | |
| if (ret != 0) | |
| return ret; | |
| /* Select nearest CLK_SYS_RATE */ | |
| best = 0; | |
| best_val = abs((wm9081->sysclk_rate / clk_sys_rates[0].ratio) | |
| - wm9081->fs); | |
| for (i = 1; i < ARRAY_SIZE(clk_sys_rates); i++) { | |
| cur_val = abs((wm9081->sysclk_rate / | |
| clk_sys_rates[i].ratio) - wm9081->fs); | |
| if (cur_val < best_val) { | |
| best = i; | |
| best_val = cur_val; | |
| } | |
| } | |
| dev_dbg(component->dev, "Selected CLK_SYS_RATIO of %d\n", | |
| clk_sys_rates[best].ratio); | |
| clk_ctrl2 |= (clk_sys_rates[best].clk_sys_rate | |
| << WM9081_CLK_SYS_RATE_SHIFT); | |
| /* SAMPLE_RATE */ | |
| best = 0; | |
| best_val = abs(wm9081->fs - sample_rates[0].rate); | |
| for (i = 1; i < ARRAY_SIZE(sample_rates); i++) { | |
| /* Closest match */ | |
| cur_val = abs(wm9081->fs - sample_rates[i].rate); | |
| if (cur_val < best_val) { | |
| best = i; | |
| best_val = cur_val; | |
| } | |
| } | |
| dev_dbg(component->dev, "Selected SAMPLE_RATE of %dHz\n", | |
| sample_rates[best].rate); | |
| clk_ctrl2 |= (sample_rates[best].sample_rate | |
| << WM9081_SAMPLE_RATE_SHIFT); | |
| /* BCLK_DIV */ | |
| best = 0; | |
| best_val = INT_MAX; | |
| for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) { | |
| cur_val = ((wm9081->sysclk_rate * 10) / bclk_divs[i].div) | |
| - wm9081->bclk; | |
| if (cur_val < 0) /* Table is sorted */ | |
| break; | |
| if (cur_val < best_val) { | |
| best = i; | |
| best_val = cur_val; | |
| } | |
| } | |
| wm9081->bclk = (wm9081->sysclk_rate * 10) / bclk_divs[best].div; | |
| dev_dbg(component->dev, "Selected BCLK_DIV of %d for %dHz BCLK\n", | |
| bclk_divs[best].div, wm9081->bclk); | |
| aif3 |= bclk_divs[best].bclk_div; | |
| /* LRCLK is a simple fraction of BCLK */ | |
| dev_dbg(component->dev, "LRCLK_RATE is %d\n", wm9081->bclk / wm9081->fs); | |
| aif4 |= wm9081->bclk / wm9081->fs; | |
| /* Apply a ReTune Mobile configuration if it's in use */ | |
| if (wm9081->pdata.num_retune_configs) { | |
| struct wm9081_pdata *pdata = &wm9081->pdata; | |
| struct wm9081_retune_mobile_setting *s; | |
| int eq1; | |
| best = 0; | |
| best_val = abs(pdata->retune_configs[0].rate - wm9081->fs); | |
| for (i = 0; i < pdata->num_retune_configs; i++) { | |
| cur_val = abs(pdata->retune_configs[i].rate - | |
| wm9081->fs); | |
| if (cur_val < best_val) { | |
| best_val = cur_val; | |
| best = i; | |
| } | |
| } | |
| s = &pdata->retune_configs[best]; | |
| dev_dbg(component->dev, "ReTune Mobile %s tuned for %dHz\n", | |
| s->name, s->rate); | |
| /* If the EQ is enabled then disable it while we write out */ | |
| eq1 = snd_soc_component_read(component, WM9081_EQ_1) & WM9081_EQ_ENA; | |
| if (eq1 & WM9081_EQ_ENA) | |
| snd_soc_component_write(component, WM9081_EQ_1, 0); | |
| /* Write out the other values */ | |
| for (i = 1; i < ARRAY_SIZE(s->config); i++) | |
| snd_soc_component_write(component, WM9081_EQ_1 + i, s->config[i]); | |
| eq1 |= (s->config[0] & ~WM9081_EQ_ENA); | |
| snd_soc_component_write(component, WM9081_EQ_1, eq1); | |
| } | |
| snd_soc_component_write(component, WM9081_CLOCK_CONTROL_2, clk_ctrl2); | |
| snd_soc_component_write(component, WM9081_AUDIO_INTERFACE_2, aif2); | |
| snd_soc_component_write(component, WM9081_AUDIO_INTERFACE_3, aif3); | |
| snd_soc_component_write(component, WM9081_AUDIO_INTERFACE_4, aif4); | |
| return 0; | |
| } | |
| static int wm9081_mute(struct snd_soc_dai *codec_dai, int mute, int direction) | |
| { | |
| struct snd_soc_component *component = codec_dai->component; | |
| unsigned int reg; | |
| reg = snd_soc_component_read(component, WM9081_DAC_DIGITAL_2); | |
| if (mute) | |
| reg |= WM9081_DAC_MUTE; | |
| else | |
| reg &= ~WM9081_DAC_MUTE; | |
| snd_soc_component_write(component, WM9081_DAC_DIGITAL_2, reg); | |
| return 0; | |
| } | |
| static int wm9081_set_sysclk(struct snd_soc_component *component, int clk_id, | |
| int source, unsigned int freq, int dir) | |
| { | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| switch (clk_id) { | |
| case WM9081_SYSCLK_MCLK: | |
| case WM9081_SYSCLK_FLL_MCLK: | |
| wm9081->sysclk_source = clk_id; | |
| wm9081->mclk_rate = freq; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static int wm9081_set_tdm_slot(struct snd_soc_dai *dai, | |
| unsigned int tx_mask, unsigned int rx_mask, int slots, int slot_width) | |
| { | |
| struct snd_soc_component *component = dai->component; | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| unsigned int aif1 = snd_soc_component_read(component, WM9081_AUDIO_INTERFACE_1); | |
| aif1 &= ~(WM9081_AIFDAC_TDM_SLOT_MASK | WM9081_AIFDAC_TDM_MODE_MASK); | |
| if (slots < 0 || slots > 4) | |
| return -EINVAL; | |
| wm9081->tdm_width = slot_width; | |
| if (slots == 0) | |
| slots = 1; | |
| aif1 |= (slots - 1) << WM9081_AIFDAC_TDM_MODE_SHIFT; | |
| switch (rx_mask) { | |
| case 1: | |
| break; | |
| case 2: | |
| aif1 |= 0x10; | |
| break; | |
| case 4: | |
| aif1 |= 0x20; | |
| break; | |
| case 8: | |
| aif1 |= 0x30; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| snd_soc_component_write(component, WM9081_AUDIO_INTERFACE_1, aif1); | |
| return 0; | |
| } | |
| #define WM9081_RATES SNDRV_PCM_RATE_8000_96000 | |
| #define WM9081_FORMATS \ | |
| (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ | |
| SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE) | |
| static const struct snd_soc_dai_ops wm9081_dai_ops = { | |
| .hw_params = wm9081_hw_params, | |
| .set_fmt = wm9081_set_dai_fmt, | |
| .mute_stream = wm9081_mute, | |
| .set_tdm_slot = wm9081_set_tdm_slot, | |
| .no_capture_mute = 1, | |
| }; | |
| /* We report two channels because the CODEC processes a stereo signal, even | |
| * though it is only capable of handling a mono output. | |
| */ | |
| static struct snd_soc_dai_driver wm9081_dai = { | |
| .name = "wm9081-hifi", | |
| .playback = { | |
| .stream_name = "AIF", | |
| .channels_min = 1, | |
| .channels_max = 2, | |
| .rates = WM9081_RATES, | |
| .formats = WM9081_FORMATS, | |
| }, | |
| .ops = &wm9081_dai_ops, | |
| }; | |
| static int wm9081_probe(struct snd_soc_component *component) | |
| { | |
| struct wm9081_priv *wm9081 = snd_soc_component_get_drvdata(component); | |
| /* Enable zero cross by default */ | |
| snd_soc_component_update_bits(component, WM9081_ANALOGUE_LINEOUT, | |
| WM9081_LINEOUTZC, WM9081_LINEOUTZC); | |
| snd_soc_component_update_bits(component, WM9081_ANALOGUE_SPEAKER_PGA, | |
| WM9081_SPKPGAZC, WM9081_SPKPGAZC); | |
| if (!wm9081->pdata.num_retune_configs) { | |
| dev_dbg(component->dev, | |
| "No ReTune Mobile data, using normal EQ\n"); | |
| snd_soc_add_component_controls(component, wm9081_eq_controls, | |
| ARRAY_SIZE(wm9081_eq_controls)); | |
| } | |
| return 0; | |
| } | |
| static const struct snd_soc_component_driver soc_component_dev_wm9081 = { | |
| .probe = wm9081_probe, | |
| .set_sysclk = wm9081_set_sysclk, | |
| .set_bias_level = wm9081_set_bias_level, | |
| .controls = wm9081_snd_controls, | |
| .num_controls = ARRAY_SIZE(wm9081_snd_controls), | |
| .dapm_widgets = wm9081_dapm_widgets, | |
| .num_dapm_widgets = ARRAY_SIZE(wm9081_dapm_widgets), | |
| .dapm_routes = wm9081_audio_paths, | |
| .num_dapm_routes = ARRAY_SIZE(wm9081_audio_paths), | |
| .use_pmdown_time = 1, | |
| .endianness = 1, | |
| }; | |
| static const struct regmap_config wm9081_regmap = { | |
| .reg_bits = 8, | |
| .val_bits = 16, | |
| .max_register = WM9081_MAX_REGISTER, | |
| .reg_defaults = wm9081_reg, | |
| .num_reg_defaults = ARRAY_SIZE(wm9081_reg), | |
| .volatile_reg = wm9081_volatile_register, | |
| .readable_reg = wm9081_readable_register, | |
| .cache_type = REGCACHE_MAPLE, | |
| }; | |
| static int wm9081_i2c_probe(struct i2c_client *i2c) | |
| { | |
| struct wm9081_priv *wm9081; | |
| unsigned int reg; | |
| int ret; | |
| wm9081 = devm_kzalloc(&i2c->dev, sizeof(struct wm9081_priv), | |
| GFP_KERNEL); | |
| if (wm9081 == NULL) | |
| return -ENOMEM; | |
| i2c_set_clientdata(i2c, wm9081); | |
| wm9081->regmap = devm_regmap_init_i2c(i2c, &wm9081_regmap); | |
| if (IS_ERR(wm9081->regmap)) { | |
| ret = PTR_ERR(wm9081->regmap); | |
| dev_err(&i2c->dev, "regmap_init() failed: %d\n", ret); | |
| return ret; | |
| } | |
| ret = regmap_read(wm9081->regmap, WM9081_SOFTWARE_RESET, ®); | |
| if (ret != 0) { | |
| dev_err(&i2c->dev, "Failed to read chip ID: %d\n", ret); | |
| return ret; | |
| } | |
| if (reg != 0x9081) { | |
| dev_err(&i2c->dev, "Device is not a WM9081: ID=0x%x\n", reg); | |
| return -EINVAL; | |
| } | |
| ret = wm9081_reset(wm9081->regmap); | |
| if (ret < 0) { | |
| dev_err(&i2c->dev, "Failed to issue reset\n"); | |
| return ret; | |
| } | |
| if (dev_get_platdata(&i2c->dev)) | |
| memcpy(&wm9081->pdata, dev_get_platdata(&i2c->dev), | |
| sizeof(wm9081->pdata)); | |
| reg = 0; | |
| if (wm9081->pdata.irq_high) | |
| reg |= WM9081_IRQ_POL; | |
| if (!wm9081->pdata.irq_cmos) | |
| reg |= WM9081_IRQ_OP_CTRL; | |
| regmap_update_bits(wm9081->regmap, WM9081_INTERRUPT_CONTROL, | |
| WM9081_IRQ_POL | WM9081_IRQ_OP_CTRL, reg); | |
| regcache_cache_only(wm9081->regmap, true); | |
| ret = devm_snd_soc_register_component(&i2c->dev, | |
| &soc_component_dev_wm9081, &wm9081_dai, 1); | |
| if (ret < 0) | |
| return ret; | |
| return 0; | |
| } | |
| static const struct i2c_device_id wm9081_i2c_id[] = { | |
| { .name = "wm9081" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, wm9081_i2c_id); | |
| static struct i2c_driver wm9081_i2c_driver = { | |
| .driver = { | |
| .name = "wm9081", | |
| }, | |
| .probe = wm9081_i2c_probe, | |
| .id_table = wm9081_i2c_id, | |
| }; | |
| module_i2c_driver(wm9081_i2c_driver); | |
| MODULE_DESCRIPTION("ASoC WM9081 driver"); | |
| MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>"); | |
| MODULE_LICENSE("GPL"); |