| // SPDX-License-Identifier: GPL-2.0-only | |
| /* Copyright (c) 2014, The Linux Foundation. All rights reserved. | |
| */ | |
| #include <linux/bits.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/of_address.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/watchdog.h> | |
| enum wdt_reg { | |
| WDT_RST, | |
| WDT_EN, | |
| WDT_STS, | |
| WDT_BARK_TIME, | |
| WDT_BITE_TIME, | |
| }; | |
| #define QCOM_WDT_ENABLE BIT(0) | |
| static const u32 reg_offset_data_apcs_tmr[] = { | |
| [WDT_RST] = 0x38, | |
| [WDT_EN] = 0x40, | |
| [WDT_STS] = 0x44, | |
| [WDT_BARK_TIME] = 0x4C, | |
| [WDT_BITE_TIME] = 0x5C, | |
| }; | |
| static const u32 reg_offset_data_kpss[] = { | |
| [WDT_RST] = 0x4, | |
| [WDT_EN] = 0x8, | |
| [WDT_STS] = 0xC, | |
| [WDT_BARK_TIME] = 0x10, | |
| [WDT_BITE_TIME] = 0x14, | |
| }; | |
| struct qcom_wdt_match_data { | |
| const u32 *offset; | |
| bool pretimeout; | |
| u32 max_tick_count; | |
| u32 wdt_reason_val; | |
| u32 powerunder_reason_val; | |
| }; | |
| struct qcom_wdt { | |
| struct watchdog_device wdd; | |
| unsigned long rate; | |
| void __iomem *base; | |
| const u32 *layout; | |
| }; | |
| static void __iomem *wdt_addr(struct qcom_wdt *wdt, enum wdt_reg reg) | |
| { | |
| return wdt->base + wdt->layout[reg]; | |
| } | |
| static inline | |
| struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd) | |
| { | |
| return container_of(wdd, struct qcom_wdt, wdd); | |
| } | |
| static irqreturn_t qcom_wdt_isr(int irq, void *arg) | |
| { | |
| struct watchdog_device *wdd = arg; | |
| watchdog_notify_pretimeout(wdd); | |
| return IRQ_HANDLED; | |
| } | |
| static int qcom_wdt_start(struct watchdog_device *wdd) | |
| { | |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); | |
| unsigned int bark = wdd->timeout - wdd->pretimeout; | |
| writel(0, wdt_addr(wdt, WDT_EN)); | |
| writel(1, wdt_addr(wdt, WDT_RST)); | |
| writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME)); | |
| writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME)); | |
| writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN)); | |
| return 0; | |
| } | |
| static int qcom_wdt_stop(struct watchdog_device *wdd) | |
| { | |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); | |
| writel(0, wdt_addr(wdt, WDT_EN)); | |
| return 0; | |
| } | |
| static int qcom_wdt_ping(struct watchdog_device *wdd) | |
| { | |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); | |
| writel(1, wdt_addr(wdt, WDT_RST)); | |
| return 0; | |
| } | |
| static int qcom_wdt_set_timeout(struct watchdog_device *wdd, | |
| unsigned int timeout) | |
| { | |
| wdd->timeout = timeout; | |
| return qcom_wdt_start(wdd); | |
| } | |
| static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd, | |
| unsigned int timeout) | |
| { | |
| wdd->pretimeout = timeout; | |
| return qcom_wdt_start(wdd); | |
| } | |
| static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action, | |
| void *data) | |
| { | |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); | |
| u32 timeout; | |
| /* | |
| * Trigger watchdog bite: | |
| * Setup BITE_TIME to be 128ms, and enable WDT. | |
| */ | |
| timeout = 128 * wdt->rate / 1000; | |
| writel(0, wdt_addr(wdt, WDT_EN)); | |
| writel(1, wdt_addr(wdt, WDT_RST)); | |
| writel(timeout, wdt_addr(wdt, WDT_BARK_TIME)); | |
| writel(timeout, wdt_addr(wdt, WDT_BITE_TIME)); | |
| writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN)); | |
| /* | |
| * Actually make sure the above sequence hits hardware before sleeping. | |
| */ | |
| wmb(); | |
| mdelay(150); | |
| return 0; | |
| } | |
| static int qcom_wdt_is_running(struct watchdog_device *wdd) | |
| { | |
| struct qcom_wdt *wdt = to_qcom_wdt(wdd); | |
| return (readl(wdt_addr(wdt, WDT_EN)) & QCOM_WDT_ENABLE); | |
| } | |
| static const struct watchdog_ops qcom_wdt_ops = { | |
| .start = qcom_wdt_start, | |
| .stop = qcom_wdt_stop, | |
| .ping = qcom_wdt_ping, | |
| .set_timeout = qcom_wdt_set_timeout, | |
| .set_pretimeout = qcom_wdt_set_pretimeout, | |
| .restart = qcom_wdt_restart, | |
| .owner = THIS_MODULE, | |
| }; | |
| static const struct watchdog_info qcom_wdt_info = { | |
| .options = WDIOF_KEEPALIVEPING | |
| | WDIOF_MAGICCLOSE | |
| | WDIOF_SETTIMEOUT | |
| | WDIOF_CARDRESET | |
| | WDIOF_POWERUNDER, | |
| .identity = KBUILD_MODNAME, | |
| }; | |
| static const struct watchdog_info qcom_wdt_pt_info = { | |
| .options = WDIOF_KEEPALIVEPING | |
| | WDIOF_MAGICCLOSE | |
| | WDIOF_SETTIMEOUT | |
| | WDIOF_PRETIMEOUT | |
| | WDIOF_CARDRESET | |
| | WDIOF_POWERUNDER, | |
| .identity = KBUILD_MODNAME, | |
| }; | |
| static const struct qcom_wdt_match_data match_data_apcs_tmr = { | |
| .offset = reg_offset_data_apcs_tmr, | |
| .pretimeout = false, | |
| .max_tick_count = 0x10000000U, | |
| }; | |
| static const struct qcom_wdt_match_data match_data_ipq5424 = { | |
| .offset = reg_offset_data_kpss, | |
| .pretimeout = true, | |
| .max_tick_count = 0xFFFFFU, | |
| .wdt_reason_val = 5, | |
| .powerunder_reason_val = 1, | |
| }; | |
| static const struct qcom_wdt_match_data match_data_ipq9574 = { | |
| .offset = reg_offset_data_kpss, | |
| .pretimeout = true, | |
| .max_tick_count = 0xFFFFFU, | |
| .wdt_reason_val = 1, | |
| .powerunder_reason_val = 32, | |
| }; | |
| static const struct qcom_wdt_match_data match_data_kpss = { | |
| .offset = reg_offset_data_kpss, | |
| .pretimeout = true, | |
| .max_tick_count = 0xFFFFFU, | |
| }; | |
| static int qcom_wdt_get_bootstatus(struct device *dev, struct qcom_wdt *wdt, | |
| const struct qcom_wdt_match_data *data) | |
| { | |
| struct device_node *imem; | |
| struct resource res; | |
| void __iomem *addr; | |
| int ret; | |
| int val; | |
| imem = of_parse_phandle(dev->of_node, "sram", 0); | |
| if (!imem) { | |
| /* Read the EXPIRED_STATUS bit as a fallback */ | |
| if (readl(wdt_addr(wdt, WDT_STS)) & 1) | |
| wdt->wdd.bootstatus = WDIOF_CARDRESET; | |
| return 0; | |
| } | |
| ret = of_address_to_resource(imem, 0, &res); | |
| of_node_put(imem); | |
| if (ret) | |
| return ret; | |
| addr = ioremap(res.start, resource_size(&res)); | |
| if (!addr) | |
| return -ENOMEM; | |
| val = readl(addr); | |
| if (val == data->wdt_reason_val) | |
| wdt->wdd.bootstatus = WDIOF_CARDRESET; | |
| else if (val == data->powerunder_reason_val) | |
| wdt->wdd.bootstatus = WDIOF_POWERUNDER; | |
| iounmap(addr); | |
| return 0; | |
| } | |
| static int qcom_wdt_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| struct qcom_wdt *wdt; | |
| struct resource *res; | |
| struct device_node *np = dev->of_node; | |
| const struct qcom_wdt_match_data *data; | |
| u32 percpu_offset; | |
| int irq, ret; | |
| struct clk *clk; | |
| data = of_device_get_match_data(dev); | |
| if (!data) { | |
| dev_err(dev, "Unsupported QCOM WDT module\n"); | |
| return -ENODEV; | |
| } | |
| wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL); | |
| if (!wdt) | |
| return -ENOMEM; | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| if (!res) | |
| return -ENOMEM; | |
| /* We use CPU0's DGT for the watchdog */ | |
| if (of_property_read_u32(np, "cpu-offset", &percpu_offset)) | |
| percpu_offset = 0; | |
| res->start += percpu_offset; | |
| res->end += percpu_offset; | |
| wdt->base = devm_ioremap_resource(dev, res); | |
| if (IS_ERR(wdt->base)) | |
| return PTR_ERR(wdt->base); | |
| clk = devm_clk_get_enabled(dev, NULL); | |
| if (IS_ERR(clk)) { | |
| dev_err(dev, "failed to get input clock\n"); | |
| return PTR_ERR(clk); | |
| } | |
| /* | |
| * We use the clock rate to calculate the max timeout, so ensure it's | |
| * not zero to avoid a divide-by-zero exception. | |
| * | |
| * WATCHDOG_CORE assumes units of seconds, if the WDT is clocked such | |
| * that it would bite before a second elapses it's usefulness is | |
| * limited. Bail if this is the case. | |
| */ | |
| wdt->rate = clk_get_rate(clk); | |
| if (wdt->rate == 0 || | |
| wdt->rate > data->max_tick_count) { | |
| dev_err(dev, "invalid clock rate\n"); | |
| return -EINVAL; | |
| } | |
| wdt->wdd.info = &qcom_wdt_info; | |
| /* check if there is pretimeout support */ | |
| if (data->pretimeout) { | |
| irq = platform_get_irq_optional(pdev, 0); | |
| if (irq < 0 && irq != -ENXIO) | |
| return irq; | |
| if (irq > 0) { | |
| ret = devm_request_irq(dev, irq, qcom_wdt_isr, 0, | |
| "wdt_bark", &wdt->wdd); | |
| if (ret) | |
| return ret; | |
| wdt->wdd.info = &qcom_wdt_pt_info; | |
| wdt->wdd.pretimeout = 1; | |
| } | |
| } | |
| wdt->wdd.ops = &qcom_wdt_ops; | |
| wdt->wdd.min_timeout = 1; | |
| wdt->wdd.max_timeout = data->max_tick_count / wdt->rate; | |
| wdt->wdd.parent = dev; | |
| wdt->layout = data->offset; | |
| ret = qcom_wdt_get_bootstatus(dev, wdt, data); | |
| if (ret) | |
| dev_err(dev, "failed to get the bootstatus, %d\n", ret); | |
| /* | |
| * If 'timeout-sec' unspecified in devicetree, assume a 30 second | |
| * default, unless the max timeout is less than 30 seconds, then use | |
| * the max instead. | |
| */ | |
| wdt->wdd.timeout = min(wdt->wdd.max_timeout, 30U); | |
| watchdog_init_timeout(&wdt->wdd, 0, dev); | |
| /* | |
| * If WDT is already running, call WDT start which | |
| * will stop the WDT, set timeouts as bootloader | |
| * might use different ones and set running bit | |
| * to inform the WDT subsystem to ping the WDT | |
| */ | |
| if (qcom_wdt_is_running(&wdt->wdd)) { | |
| qcom_wdt_start(&wdt->wdd); | |
| set_bit(WDOG_HW_RUNNING, &wdt->wdd.status); | |
| } | |
| ret = devm_watchdog_register_device(dev, &wdt->wdd); | |
| if (ret) | |
| return ret; | |
| platform_set_drvdata(pdev, wdt); | |
| return 0; | |
| } | |
| static int __maybe_unused qcom_wdt_suspend(struct device *dev) | |
| { | |
| struct qcom_wdt *wdt = dev_get_drvdata(dev); | |
| if (watchdog_active(&wdt->wdd)) | |
| qcom_wdt_stop(&wdt->wdd); | |
| return 0; | |
| } | |
| static int __maybe_unused qcom_wdt_resume(struct device *dev) | |
| { | |
| struct qcom_wdt *wdt = dev_get_drvdata(dev); | |
| if (watchdog_active(&wdt->wdd)) | |
| qcom_wdt_start(&wdt->wdd); | |
| return 0; | |
| } | |
| static const struct dev_pm_ops qcom_wdt_pm_ops = { | |
| SET_LATE_SYSTEM_SLEEP_PM_OPS(qcom_wdt_suspend, qcom_wdt_resume) | |
| }; | |
| static const struct of_device_id qcom_wdt_of_table[] = { | |
| { .compatible = "qcom,apss-wdt-ipq5332", .data = &match_data_ipq9574 }, | |
| { .compatible = "qcom,apss-wdt-ipq5424", .data = &match_data_ipq5424 }, | |
| { .compatible = "qcom,apss-wdt-ipq9574", .data = &match_data_ipq9574 }, | |
| { .compatible = "qcom,kpss-timer", .data = &match_data_apcs_tmr }, | |
| { .compatible = "qcom,scss-timer", .data = &match_data_apcs_tmr }, | |
| { .compatible = "qcom,kpss-wdt", .data = &match_data_kpss }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, qcom_wdt_of_table); | |
| static struct platform_driver qcom_watchdog_driver = { | |
| .probe = qcom_wdt_probe, | |
| .driver = { | |
| .name = KBUILD_MODNAME, | |
| .of_match_table = qcom_wdt_of_table, | |
| .pm = &qcom_wdt_pm_ops, | |
| }, | |
| }; | |
| module_platform_driver(qcom_watchdog_driver); | |
| MODULE_DESCRIPTION("QCOM KPSS Watchdog Driver"); | |
| MODULE_LICENSE("GPL v2"); |