| // SPDX-License-Identifier: GPL-2.0-or-later | |
| /* | |
| * Copyright 2016 IBM Corporation | |
| * | |
| * Joel Stanley <joel@jms.id.au> | |
| */ | |
| #include <linux/bits.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/kernel.h> | |
| #include <linux/kstrtox.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regmap.h> | |
| #include <linux/watchdog.h> | |
| static bool nowayout = WATCHDOG_NOWAYOUT; | |
| module_param(nowayout, bool, 0); | |
| MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" | |
| __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); | |
| struct aspeed_wdt_scu { | |
| const char *compatible; | |
| u32 reset_status_reg; | |
| u32 wdt_reset_mask; | |
| u32 wdt_reset_mask_shift; | |
| }; | |
| struct aspeed_wdt_config { | |
| u32 ext_pulse_width_mask; | |
| u32 irq_shift; | |
| u32 irq_mask; | |
| struct aspeed_wdt_scu scu; | |
| u32 num_reset_masks; | |
| }; | |
| struct aspeed_wdt { | |
| struct watchdog_device wdd; | |
| void __iomem *base; | |
| u32 ctrl; | |
| const struct aspeed_wdt_config *cfg; | |
| }; | |
| static const struct aspeed_wdt_config ast2400_config = { | |
| .ext_pulse_width_mask = 0xff, | |
| .irq_shift = 0, | |
| .irq_mask = 0, | |
| .scu = { | |
| .compatible = "aspeed,ast2400-scu", | |
| .reset_status_reg = 0x3c, | |
| .wdt_reset_mask = 0x1, | |
| .wdt_reset_mask_shift = 1, | |
| }, | |
| }; | |
| static const struct aspeed_wdt_config ast2500_config = { | |
| .ext_pulse_width_mask = 0xfffff, | |
| .irq_shift = 12, | |
| .irq_mask = GENMASK(31, 12), | |
| .scu = { | |
| .compatible = "aspeed,ast2500-scu", | |
| .reset_status_reg = 0x3c, | |
| .wdt_reset_mask = 0x1, | |
| .wdt_reset_mask_shift = 2, | |
| }, | |
| .num_reset_masks = 1, | |
| }; | |
| static const struct aspeed_wdt_config ast2600_config = { | |
| .ext_pulse_width_mask = 0xfffff, | |
| .irq_shift = 0, | |
| .irq_mask = GENMASK(31, 10), | |
| .scu = { | |
| .compatible = "aspeed,ast2600-scu", | |
| .reset_status_reg = 0x74, | |
| .wdt_reset_mask = 0xf, | |
| .wdt_reset_mask_shift = 16, | |
| }, | |
| .num_reset_masks = 2, | |
| }; | |
| static const struct aspeed_wdt_config ast2700_config = { | |
| .ext_pulse_width_mask = 0xfffff, | |
| .irq_shift = 0, | |
| .irq_mask = GENMASK(31, 10), | |
| .scu = { | |
| .compatible = "aspeed,ast2700-scu0", | |
| .reset_status_reg = 0x70, | |
| .wdt_reset_mask = 0xf, | |
| .wdt_reset_mask_shift = 0, | |
| }, | |
| .num_reset_masks = 5, | |
| }; | |
| static const struct of_device_id aspeed_wdt_of_table[] = { | |
| { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config }, | |
| { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config }, | |
| { .compatible = "aspeed,ast2600-wdt", .data = &ast2600_config }, | |
| { .compatible = "aspeed,ast2700-wdt", .data = &ast2700_config }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); | |
| #define WDT_STATUS 0x00 | |
| #define WDT_RELOAD_VALUE 0x04 | |
| #define WDT_RESTART 0x08 | |
| #define WDT_CTRL 0x0C | |
| #define WDT_CTRL_BOOT_SECONDARY BIT(7) | |
| #define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) | |
| #define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) | |
| #define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) | |
| #define WDT_CTRL_1MHZ_CLK BIT(4) | |
| #define WDT_CTRL_WDT_EXT BIT(3) | |
| #define WDT_CTRL_WDT_INTR BIT(2) | |
| #define WDT_CTRL_RESET_SYSTEM BIT(1) | |
| #define WDT_CTRL_ENABLE BIT(0) | |
| #define WDT_TIMEOUT_STATUS 0x10 | |
| #define WDT_TIMEOUT_STATUS_IRQ BIT(2) | |
| #define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) | |
| #define WDT_CLEAR_TIMEOUT_STATUS 0x14 | |
| #define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) | |
| #define WDT_RESET_MASK1 0x1c | |
| #define WDT_RESET_MASK2 0x20 | |
| /* | |
| * WDT_RESET_WIDTH controls the characteristics of the external pulse (if | |
| * enabled), specifically: | |
| * | |
| * * Pulse duration | |
| * * Drive mode: push-pull vs open-drain | |
| * * Polarity: Active high or active low | |
| * | |
| * Pulse duration configuration is available on both the AST2400 and AST2500, | |
| * though the field changes between SoCs: | |
| * | |
| * AST2400: Bits 7:0 | |
| * AST2500: Bits 19:0 | |
| * | |
| * This difference is captured in struct aspeed_wdt_config. | |
| * | |
| * The AST2500 exposes the drive mode and polarity options, but not in a | |
| * regular fashion. For read purposes, bit 31 represents active high or low, | |
| * and bit 30 represents push-pull or open-drain. With respect to write, magic | |
| * values need to be written to the top byte to change the state of the drive | |
| * mode and polarity bits. Any other value written to the top byte has no | |
| * effect on the state of the drive mode or polarity bits. However, the pulse | |
| * width value must be preserved (as desired) if written. | |
| */ | |
| #define WDT_RESET_WIDTH 0x18 | |
| #define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31) | |
| #define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24) | |
| #define WDT_ACTIVE_LOW_MAGIC (0x5A << 24) | |
| #define WDT_RESET_WIDTH_PUSH_PULL BIT(30) | |
| #define WDT_PUSH_PULL_MAGIC (0xA8 << 24) | |
| #define WDT_OPEN_DRAIN_MAGIC (0x8A << 24) | |
| #define WDT_RESTART_MAGIC 0x4755 | |
| /* 32 bits at 1MHz, in milliseconds */ | |
| #define WDT_MAX_TIMEOUT_MS 4294967 | |
| #define WDT_DEFAULT_TIMEOUT 30 | |
| #define WDT_RATE_1MHZ 1000000 | |
| static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd) | |
| { | |
| return container_of(wdd, struct aspeed_wdt, wdd); | |
| } | |
| static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count) | |
| { | |
| wdt->ctrl |= WDT_CTRL_ENABLE; | |
| writel(0, wdt->base + WDT_CTRL); | |
| writel(count, wdt->base + WDT_RELOAD_VALUE); | |
| writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); | |
| writel(wdt->ctrl, wdt->base + WDT_CTRL); | |
| } | |
| static int aspeed_wdt_start(struct watchdog_device *wdd) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ); | |
| return 0; | |
| } | |
| static int aspeed_wdt_stop(struct watchdog_device *wdd) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| wdt->ctrl &= ~WDT_CTRL_ENABLE; | |
| writel(wdt->ctrl, wdt->base + WDT_CTRL); | |
| return 0; | |
| } | |
| static int aspeed_wdt_ping(struct watchdog_device *wdd) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); | |
| return 0; | |
| } | |
| static int aspeed_wdt_set_timeout(struct watchdog_device *wdd, | |
| unsigned int timeout) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| u32 actual; | |
| wdd->timeout = timeout; | |
| actual = min(timeout, wdd->max_hw_heartbeat_ms / 1000); | |
| writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE); | |
| writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); | |
| return 0; | |
| } | |
| static int aspeed_wdt_set_pretimeout(struct watchdog_device *wdd, | |
| unsigned int pretimeout) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| u32 actual = pretimeout * WDT_RATE_1MHZ; | |
| u32 s = wdt->cfg->irq_shift; | |
| u32 m = wdt->cfg->irq_mask; | |
| wdd->pretimeout = pretimeout; | |
| wdt->ctrl &= ~m; | |
| if (pretimeout) | |
| wdt->ctrl |= ((actual << s) & m) | WDT_CTRL_WDT_INTR; | |
| else | |
| wdt->ctrl &= ~WDT_CTRL_WDT_INTR; | |
| writel(wdt->ctrl, wdt->base + WDT_CTRL); | |
| return 0; | |
| } | |
| static int aspeed_wdt_restart(struct watchdog_device *wdd, | |
| unsigned long action, void *data) | |
| { | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY; | |
| aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000); | |
| mdelay(1000); | |
| return 0; | |
| } | |
| static void aspeed_wdt_update_bootstatus(struct platform_device *pdev, | |
| struct aspeed_wdt *wdt) | |
| { | |
| const struct resource *res; | |
| struct aspeed_wdt_scu scu = wdt->cfg->scu; | |
| struct regmap *scu_base; | |
| u32 reset_mask_width; | |
| u32 reset_mask_shift; | |
| u32 idx = 0; | |
| u32 status; | |
| int ret; | |
| if (!of_device_is_compatible(pdev->dev.of_node, "aspeed,ast2400-wdt")) { | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| idx = ((intptr_t)wdt->base & 0x00000fff) / (uintptr_t)resource_size(res); | |
| } | |
| scu_base = syscon_regmap_lookup_by_compatible(scu.compatible); | |
| if (IS_ERR(scu_base)) { | |
| wdt->wdd.bootstatus = WDIOS_UNKNOWN; | |
| return; | |
| } | |
| ret = regmap_read(scu_base, scu.reset_status_reg, &status); | |
| if (ret) { | |
| wdt->wdd.bootstatus = WDIOS_UNKNOWN; | |
| return; | |
| } | |
| reset_mask_width = hweight32(scu.wdt_reset_mask); | |
| reset_mask_shift = scu.wdt_reset_mask_shift + | |
| reset_mask_width * idx; | |
| if (status & (scu.wdt_reset_mask << reset_mask_shift)) | |
| wdt->wdd.bootstatus = WDIOF_CARDRESET; | |
| /* clear wdt reset event flag */ | |
| if (of_device_is_compatible(pdev->dev.of_node, "aspeed,ast2400-wdt") || | |
| of_device_is_compatible(pdev->dev.of_node, "aspeed,ast2500-wdt")) { | |
| ret = regmap_read(scu_base, scu.reset_status_reg, &status); | |
| if (!ret) { | |
| status &= ~(scu.wdt_reset_mask << reset_mask_shift); | |
| regmap_write(scu_base, scu.reset_status_reg, status); | |
| } | |
| } else { | |
| regmap_write(scu_base, scu.reset_status_reg, | |
| scu.wdt_reset_mask << reset_mask_shift); | |
| } | |
| } | |
| /* access_cs0 shows if cs0 is accessible, hence the reverted bit */ | |
| static ssize_t access_cs0_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| struct aspeed_wdt *wdt = dev_get_drvdata(dev); | |
| u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS); | |
| return sysfs_emit(buf, "%u\n", | |
| !(status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY)); | |
| } | |
| static ssize_t access_cs0_store(struct device *dev, | |
| struct device_attribute *attr, const char *buf, | |
| size_t size) | |
| { | |
| struct aspeed_wdt *wdt = dev_get_drvdata(dev); | |
| unsigned long val; | |
| if (kstrtoul(buf, 10, &val)) | |
| return -EINVAL; | |
| if (val) | |
| writel(WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION, | |
| wdt->base + WDT_CLEAR_TIMEOUT_STATUS); | |
| return size; | |
| } | |
| /* | |
| * This attribute exists only if the system has booted from the alternate | |
| * flash with 'alt-boot' option. | |
| * | |
| * At alternate flash the 'access_cs0' sysfs node provides: | |
| * ast2400: a way to get access to the primary SPI flash chip at CS0 | |
| * after booting from the alternate chip at CS1. | |
| * ast2500: a way to restore the normal address mapping from | |
| * (CS0->CS1, CS1->CS0) to (CS0->CS0, CS1->CS1). | |
| * | |
| * Clearing the boot code selection and timeout counter also resets to the | |
| * initial state the chip select line mapping. When the SoC is in normal | |
| * mapping state (i.e. booted from CS0), clearing those bits does nothing for | |
| * both versions of the SoC. For alternate boot mode (booted from CS1 due to | |
| * wdt2 expiration) the behavior differs as described above. | |
| * | |
| * This option can be used with wdt2 (watchdog1) only. | |
| */ | |
| static DEVICE_ATTR_RW(access_cs0); | |
| static struct attribute *bswitch_attrs[] = { | |
| &dev_attr_access_cs0.attr, | |
| NULL | |
| }; | |
| ATTRIBUTE_GROUPS(bswitch); | |
| static const struct watchdog_ops aspeed_wdt_ops = { | |
| .start = aspeed_wdt_start, | |
| .stop = aspeed_wdt_stop, | |
| .ping = aspeed_wdt_ping, | |
| .set_timeout = aspeed_wdt_set_timeout, | |
| .set_pretimeout = aspeed_wdt_set_pretimeout, | |
| .restart = aspeed_wdt_restart, | |
| .owner = THIS_MODULE, | |
| }; | |
| static const struct watchdog_info aspeed_wdt_info = { | |
| .options = WDIOF_KEEPALIVEPING | |
| | WDIOF_MAGICCLOSE | |
| | WDIOF_SETTIMEOUT, | |
| .identity = KBUILD_MODNAME, | |
| }; | |
| static const struct watchdog_info aspeed_wdt_pretimeout_info = { | |
| .options = WDIOF_KEEPALIVEPING | |
| | WDIOF_PRETIMEOUT | |
| | WDIOF_MAGICCLOSE | |
| | WDIOF_SETTIMEOUT, | |
| .identity = KBUILD_MODNAME, | |
| }; | |
| static irqreturn_t aspeed_wdt_irq(int irq, void *arg) | |
| { | |
| struct watchdog_device *wdd = arg; | |
| struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); | |
| u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS); | |
| if (status & WDT_TIMEOUT_STATUS_IRQ) | |
| watchdog_notify_pretimeout(wdd); | |
| return IRQ_HANDLED; | |
| } | |
| static int aspeed_wdt_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| const struct of_device_id *ofdid; | |
| struct aspeed_wdt *wdt; | |
| struct device_node *np; | |
| const char *reset_type; | |
| u32 duration; | |
| u32 status; | |
| int ret; | |
| wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL); | |
| if (!wdt) | |
| return -ENOMEM; | |
| np = dev->of_node; | |
| ofdid = of_match_node(aspeed_wdt_of_table, np); | |
| if (!ofdid) | |
| return -EINVAL; | |
| wdt->cfg = ofdid->data; | |
| wdt->base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(wdt->base)) | |
| return PTR_ERR(wdt->base); | |
| wdt->wdd.info = &aspeed_wdt_info; | |
| if (wdt->cfg->irq_mask) { | |
| int irq = platform_get_irq_optional(pdev, 0); | |
| if (irq < 0 && irq != -ENXIO) | |
| return irq; | |
| if (irq > 0) { | |
| ret = devm_request_irq(dev, irq, aspeed_wdt_irq, | |
| IRQF_SHARED, dev_name(dev), | |
| wdt); | |
| if (ret) | |
| return ret; | |
| wdt->wdd.info = &aspeed_wdt_pretimeout_info; | |
| } | |
| } | |
| wdt->wdd.ops = &aspeed_wdt_ops; | |
| wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS; | |
| wdt->wdd.parent = dev; | |
| wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT; | |
| watchdog_init_timeout(&wdt->wdd, 0, dev); | |
| watchdog_set_nowayout(&wdt->wdd, nowayout); | |
| /* | |
| * On clock rates: | |
| * - ast2400 wdt can run at PCLK, or 1MHz | |
| * - ast2500 only runs at 1MHz, hard coding bit 4 to 1 | |
| * - ast2600 always runs at 1MHz | |
| * | |
| * Set the ast2400 to run at 1MHz as it simplifies the driver. | |
| */ | |
| if (of_device_is_compatible(np, "aspeed,ast2400-wdt")) | |
| wdt->ctrl = WDT_CTRL_1MHZ_CLK; | |
| /* | |
| * Control reset on a per-device basis to ensure the | |
| * host is not affected by a BMC reboot | |
| */ | |
| ret = of_property_read_string(np, "aspeed,reset-type", &reset_type); | |
| if (ret) { | |
| wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM; | |
| } else { | |
| if (!strcmp(reset_type, "cpu")) | |
| wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU | | |
| WDT_CTRL_RESET_SYSTEM; | |
| else if (!strcmp(reset_type, "soc")) | |
| wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | | |
| WDT_CTRL_RESET_SYSTEM; | |
| else if (!strcmp(reset_type, "system")) | |
| wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP | | |
| WDT_CTRL_RESET_SYSTEM; | |
| else if (strcmp(reset_type, "none")) | |
| return -EINVAL; | |
| } | |
| if (of_property_read_bool(np, "aspeed,external-signal")) | |
| wdt->ctrl |= WDT_CTRL_WDT_EXT; | |
| if (of_property_read_bool(np, "aspeed,alt-boot")) | |
| wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY; | |
| if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) { | |
| /* | |
| * The watchdog is running, but invoke aspeed_wdt_start() to | |
| * write wdt->ctrl to WDT_CTRL to ensure the watchdog's | |
| * configuration conforms to the driver's expectations. | |
| * Primarily, ensure we're using the 1MHz clock source. | |
| */ | |
| aspeed_wdt_start(&wdt->wdd); | |
| set_bit(WDOG_HW_RUNNING, &wdt->wdd.status); | |
| } | |
| if (!of_device_is_compatible(np, "aspeed,ast2400-wdt")) { | |
| u32 reset_mask[5]; | |
| size_t nrstmask = wdt->cfg->num_reset_masks; | |
| u32 reg = readl(wdt->base + WDT_RESET_WIDTH); | |
| int i; | |
| reg &= wdt->cfg->ext_pulse_width_mask; | |
| if (of_property_read_bool(np, "aspeed,ext-active-high")) | |
| reg |= WDT_ACTIVE_HIGH_MAGIC; | |
| else | |
| reg |= WDT_ACTIVE_LOW_MAGIC; | |
| writel(reg, wdt->base + WDT_RESET_WIDTH); | |
| reg &= wdt->cfg->ext_pulse_width_mask; | |
| if (of_property_read_bool(np, "aspeed,ext-push-pull")) | |
| reg |= WDT_PUSH_PULL_MAGIC; | |
| else | |
| reg |= WDT_OPEN_DRAIN_MAGIC; | |
| writel(reg, wdt->base + WDT_RESET_WIDTH); | |
| ret = of_property_read_u32_array(np, "aspeed,reset-mask", reset_mask, nrstmask); | |
| if (!ret) { | |
| for (i = 0; i < nrstmask; i++) | |
| writel(reset_mask[i], wdt->base + WDT_RESET_MASK1 + i * 4); | |
| } | |
| } | |
| if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) { | |
| u32 max_duration = wdt->cfg->ext_pulse_width_mask + 1; | |
| if (duration == 0 || duration > max_duration) { | |
| dev_err(dev, "Invalid pulse duration: %uus\n", | |
| duration); | |
| duration = max(1U, min(max_duration, duration)); | |
| dev_info(dev, "Pulse duration set to %uus\n", | |
| duration); | |
| } | |
| /* | |
| * The watchdog is always configured with a 1MHz source, so | |
| * there is no need to scale the microsecond value. However we | |
| * need to offset it - from the datasheet: | |
| * | |
| * "This register decides the asserting duration of wdt_ext and | |
| * wdt_rstarm signal. The default value is 0xFF. It means the | |
| * default asserting duration of wdt_ext and wdt_rstarm is | |
| * 256us." | |
| * | |
| * This implies a value of 0 gives a 1us pulse. | |
| */ | |
| writel(duration - 1, wdt->base + WDT_RESET_WIDTH); | |
| } | |
| aspeed_wdt_update_bootstatus(pdev, wdt); | |
| status = readl(wdt->base + WDT_TIMEOUT_STATUS); | |
| if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) { | |
| if (of_device_is_compatible(np, "aspeed,ast2400-wdt") || | |
| of_device_is_compatible(np, "aspeed,ast2500-wdt")) | |
| wdt->wdd.groups = bswitch_groups; | |
| } | |
| dev_set_drvdata(dev, wdt); | |
| return devm_watchdog_register_device(dev, &wdt->wdd); | |
| } | |
| static struct platform_driver aspeed_watchdog_driver = { | |
| .probe = aspeed_wdt_probe, | |
| .driver = { | |
| .name = KBUILD_MODNAME, | |
| .of_match_table = aspeed_wdt_of_table, | |
| }, | |
| }; | |
| static int __init aspeed_wdt_init(void) | |
| { | |
| return platform_driver_register(&aspeed_watchdog_driver); | |
| } | |
| arch_initcall(aspeed_wdt_init); | |
| static void __exit aspeed_wdt_exit(void) | |
| { | |
| platform_driver_unregister(&aspeed_watchdog_driver); | |
| } | |
| module_exit(aspeed_wdt_exit); | |
| MODULE_DESCRIPTION("Aspeed Watchdog Driver"); | |
| MODULE_LICENSE("GPL"); |