| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * udc.c - ChipIdea UDC driver | |
| * | |
| * Copyright (C) 2008 Chipidea - MIPS Technologies, Inc. All rights reserved. | |
| * | |
| * Author: David Lopo | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/device.h> | |
| #include <linux/dmapool.h> | |
| #include <linux/dma-direct.h> | |
| #include <linux/err.h> | |
| #include <linux/irqreturn.h> | |
| #include <linux/kernel.h> | |
| #include <linux/slab.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/pinctrl/consumer.h> | |
| #include <linux/usb/ch9.h> | |
| #include <linux/usb/gadget.h> | |
| #include <linux/usb/otg-fsm.h> | |
| #include <linux/usb/chipidea.h> | |
| #include "ci.h" | |
| #include "udc.h" | |
| #include "bits.h" | |
| #include "otg.h" | |
| #include "otg_fsm.h" | |
| #include "trace.h" | |
| /* control endpoint description */ | |
| static const struct usb_endpoint_descriptor | |
| ctrl_endpt_out_desc = { | |
| .bLength = USB_DT_ENDPOINT_SIZE, | |
| .bDescriptorType = USB_DT_ENDPOINT, | |
| .bEndpointAddress = USB_DIR_OUT, | |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, | |
| .wMaxPacketSize = cpu_to_le16(CTRL_PAYLOAD_MAX), | |
| }; | |
| static const struct usb_endpoint_descriptor | |
| ctrl_endpt_in_desc = { | |
| .bLength = USB_DT_ENDPOINT_SIZE, | |
| .bDescriptorType = USB_DT_ENDPOINT, | |
| .bEndpointAddress = USB_DIR_IN, | |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, | |
| .wMaxPacketSize = cpu_to_le16(CTRL_PAYLOAD_MAX), | |
| }; | |
| static int reprime_dtd(struct ci_hdrc *ci, struct ci_hw_ep *hwep, | |
| struct td_node *node); | |
| /** | |
| * hw_ep_bit: calculates the bit number | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * | |
| * This function returns bit number | |
| */ | |
| static inline int hw_ep_bit(int num, int dir) | |
| { | |
| return num + ((dir == TX) ? 16 : 0); | |
| } | |
| static inline int ep_to_bit(struct ci_hdrc *ci, int n) | |
| { | |
| int fill = 16 - ci->hw_ep_max / 2; | |
| if (n >= ci->hw_ep_max / 2) | |
| n += fill; | |
| return n; | |
| } | |
| /** | |
| * hw_device_state: enables/disables interrupts (execute without interruption) | |
| * @ci: the controller | |
| * @dma: 0 => disable, !0 => enable and set dma engine | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_device_state(struct ci_hdrc *ci, u32 dma) | |
| { | |
| if (dma) { | |
| hw_write(ci, OP_ENDPTLISTADDR, ~0, dma); | |
| /* interrupt, error, port change, reset, sleep/suspend */ | |
| hw_write(ci, OP_USBINTR, ~0, | |
| USBi_UI|USBi_UEI|USBi_PCI|USBi_URI); | |
| } else { | |
| hw_write(ci, OP_USBINTR, ~0, 0); | |
| } | |
| return 0; | |
| } | |
| /** | |
| * hw_ep_flush: flush endpoint fifo (execute without interruption) | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_ep_flush(struct ci_hdrc *ci, int num, int dir) | |
| { | |
| int n = hw_ep_bit(num, dir); | |
| do { | |
| /* flush any pending transfer */ | |
| hw_write(ci, OP_ENDPTFLUSH, ~0, BIT(n)); | |
| while (hw_read(ci, OP_ENDPTFLUSH, BIT(n))) | |
| cpu_relax(); | |
| } while (hw_read(ci, OP_ENDPTSTAT, BIT(n))); | |
| return 0; | |
| } | |
| /** | |
| * hw_ep_disable: disables endpoint (execute without interruption) | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_ep_disable(struct ci_hdrc *ci, int num, int dir) | |
| { | |
| hw_write(ci, OP_ENDPTCTRL + num, | |
| (dir == TX) ? ENDPTCTRL_TXE : ENDPTCTRL_RXE, 0); | |
| return 0; | |
| } | |
| /** | |
| * hw_ep_enable: enables endpoint (execute without interruption) | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * @type: endpoint type | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_ep_enable(struct ci_hdrc *ci, int num, int dir, int type) | |
| { | |
| u32 mask, data; | |
| if (dir == TX) { | |
| mask = ENDPTCTRL_TXT; /* type */ | |
| data = type << __ffs(mask); | |
| mask |= ENDPTCTRL_TXS; /* unstall */ | |
| mask |= ENDPTCTRL_TXR; /* reset data toggle */ | |
| data |= ENDPTCTRL_TXR; | |
| mask |= ENDPTCTRL_TXE; /* enable */ | |
| data |= ENDPTCTRL_TXE; | |
| } else { | |
| mask = ENDPTCTRL_RXT; /* type */ | |
| data = type << __ffs(mask); | |
| mask |= ENDPTCTRL_RXS; /* unstall */ | |
| mask |= ENDPTCTRL_RXR; /* reset data toggle */ | |
| data |= ENDPTCTRL_RXR; | |
| mask |= ENDPTCTRL_RXE; /* enable */ | |
| data |= ENDPTCTRL_RXE; | |
| } | |
| hw_write(ci, OP_ENDPTCTRL + num, mask, data); | |
| return 0; | |
| } | |
| /** | |
| * hw_ep_get_halt: return endpoint halt status | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * | |
| * This function returns 1 if endpoint halted | |
| */ | |
| static int hw_ep_get_halt(struct ci_hdrc *ci, int num, int dir) | |
| { | |
| u32 mask = (dir == TX) ? ENDPTCTRL_TXS : ENDPTCTRL_RXS; | |
| return hw_read(ci, OP_ENDPTCTRL + num, mask) ? 1 : 0; | |
| } | |
| /** | |
| * hw_ep_prime: primes endpoint (execute without interruption) | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * @is_ctrl: true if control endpoint | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_ep_prime(struct ci_hdrc *ci, int num, int dir, int is_ctrl) | |
| { | |
| int n = hw_ep_bit(num, dir); | |
| /* Synchronize before ep prime */ | |
| wmb(); | |
| if (is_ctrl && dir == RX && hw_read(ci, OP_ENDPTSETUPSTAT, BIT(num))) | |
| return -EAGAIN; | |
| hw_write(ci, OP_ENDPTPRIME, ~0, BIT(n)); | |
| while (hw_read(ci, OP_ENDPTPRIME, BIT(n))) | |
| cpu_relax(); | |
| if (is_ctrl && dir == RX && hw_read(ci, OP_ENDPTSETUPSTAT, BIT(num))) | |
| return -EAGAIN; | |
| /* status shoult be tested according with manual but it doesn't work */ | |
| return 0; | |
| } | |
| /** | |
| * hw_ep_set_halt: configures ep halt & resets data toggle after clear (execute | |
| * without interruption) | |
| * @ci: the controller | |
| * @num: endpoint number | |
| * @dir: endpoint direction | |
| * @value: true => stall, false => unstall | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_ep_set_halt(struct ci_hdrc *ci, int num, int dir, int value) | |
| { | |
| if (value != 0 && value != 1) | |
| return -EINVAL; | |
| do { | |
| enum ci_hw_regs reg = OP_ENDPTCTRL + num; | |
| u32 mask_xs = (dir == TX) ? ENDPTCTRL_TXS : ENDPTCTRL_RXS; | |
| u32 mask_xr = (dir == TX) ? ENDPTCTRL_TXR : ENDPTCTRL_RXR; | |
| /* data toggle - reserved for EP0 but it's in ESS */ | |
| hw_write(ci, reg, mask_xs|mask_xr, | |
| value ? mask_xs : mask_xr); | |
| } while (value != hw_ep_get_halt(ci, num, dir)); | |
| return 0; | |
| } | |
| /** | |
| * hw_port_is_high_speed: test if port is high speed | |
| * @ci: the controller | |
| * | |
| * This function returns true if high speed port | |
| */ | |
| static int hw_port_is_high_speed(struct ci_hdrc *ci) | |
| { | |
| return ci->hw_bank.lpm ? hw_read(ci, OP_DEVLC, DEVLC_PSPD) : | |
| hw_read(ci, OP_PORTSC, PORTSC_HSP); | |
| } | |
| /** | |
| * hw_test_and_clear_complete: test & clear complete status (execute without | |
| * interruption) | |
| * @ci: the controller | |
| * @n: endpoint number | |
| * | |
| * This function returns complete status | |
| */ | |
| static int hw_test_and_clear_complete(struct ci_hdrc *ci, int n) | |
| { | |
| n = ep_to_bit(ci, n); | |
| return hw_test_and_clear(ci, OP_ENDPTCOMPLETE, BIT(n)); | |
| } | |
| /** | |
| * hw_test_and_clear_intr_active: test & clear active interrupts (execute | |
| * without interruption) | |
| * @ci: the controller | |
| * | |
| * This function returns active interrutps | |
| */ | |
| static u32 hw_test_and_clear_intr_active(struct ci_hdrc *ci) | |
| { | |
| u32 reg = hw_read_intr_status(ci) & hw_read_intr_enable(ci); | |
| hw_write(ci, OP_USBSTS, ~0, reg); | |
| return reg; | |
| } | |
| /** | |
| * hw_test_and_clear_setup_guard: test & clear setup guard (execute without | |
| * interruption) | |
| * @ci: the controller | |
| * | |
| * This function returns guard value | |
| */ | |
| static int hw_test_and_clear_setup_guard(struct ci_hdrc *ci) | |
| { | |
| return hw_test_and_write(ci, OP_USBCMD, USBCMD_SUTW, 0); | |
| } | |
| /** | |
| * hw_test_and_set_setup_guard: test & set setup guard (execute without | |
| * interruption) | |
| * @ci: the controller | |
| * | |
| * This function returns guard value | |
| */ | |
| static int hw_test_and_set_setup_guard(struct ci_hdrc *ci) | |
| { | |
| return hw_test_and_write(ci, OP_USBCMD, USBCMD_SUTW, USBCMD_SUTW); | |
| } | |
| /** | |
| * hw_usb_set_address: configures USB address (execute without interruption) | |
| * @ci: the controller | |
| * @value: new USB address | |
| * | |
| * This function explicitly sets the address, without the "USBADRA" (advance) | |
| * feature, which is not supported by older versions of the controller. | |
| */ | |
| static void hw_usb_set_address(struct ci_hdrc *ci, u8 value) | |
| { | |
| hw_write(ci, OP_DEVICEADDR, DEVICEADDR_USBADR, | |
| value << __ffs(DEVICEADDR_USBADR)); | |
| } | |
| /** | |
| * hw_usb_reset: restart device after a bus reset (execute without | |
| * interruption) | |
| * @ci: the controller | |
| * | |
| * This function returns an error code | |
| */ | |
| static int hw_usb_reset(struct ci_hdrc *ci) | |
| { | |
| hw_usb_set_address(ci, 0); | |
| /* ESS flushes only at end?!? */ | |
| hw_write(ci, OP_ENDPTFLUSH, ~0, ~0); | |
| /* clear setup token semaphores */ | |
| hw_write(ci, OP_ENDPTSETUPSTAT, 0, 0); | |
| /* clear complete status */ | |
| hw_write(ci, OP_ENDPTCOMPLETE, 0, 0); | |
| /* wait until all bits cleared */ | |
| while (hw_read(ci, OP_ENDPTPRIME, ~0)) | |
| udelay(10); /* not RTOS friendly */ | |
| /* reset all endpoints ? */ | |
| /* reset internal status and wait for further instructions | |
| no need to verify the port reset status (ESS does it) */ | |
| return 0; | |
| } | |
| /****************************************************************************** | |
| * UTIL block | |
| *****************************************************************************/ | |
| static int add_td_to_list(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq, | |
| unsigned int length, struct scatterlist *s) | |
| { | |
| int i; | |
| u32 temp; | |
| struct td_node *lastnode, *node = kzalloc_obj(struct td_node, | |
| GFP_ATOMIC); | |
| if (node == NULL) | |
| return -ENOMEM; | |
| node->ptr = dma_pool_zalloc(hwep->td_pool, GFP_ATOMIC, &node->dma); | |
| if (node->ptr == NULL) { | |
| kfree(node); | |
| return -ENOMEM; | |
| } | |
| node->ptr->token = cpu_to_le32(length << __ffs(TD_TOTAL_BYTES)); | |
| node->ptr->token &= cpu_to_le32(TD_TOTAL_BYTES); | |
| node->ptr->token |= cpu_to_le32(TD_STATUS_ACTIVE); | |
| if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == TX) { | |
| u32 mul = hwreq->req.length / hwep->ep.maxpacket; | |
| if (hwreq->req.length == 0 | |
| || hwreq->req.length % hwep->ep.maxpacket) | |
| mul++; | |
| node->ptr->token |= cpu_to_le32(mul << __ffs(TD_MULTO)); | |
| } | |
| if (s) { | |
| temp = (u32) (sg_dma_address(s) + hwreq->req.actual); | |
| node->td_remaining_size = CI_MAX_BUF_SIZE - length; | |
| } else { | |
| temp = (u32) (hwreq->req.dma + hwreq->req.actual); | |
| } | |
| if (length) { | |
| node->ptr->page[0] = cpu_to_le32(temp); | |
| for (i = 1; i < TD_PAGE_COUNT; i++) { | |
| u32 page = temp + i * CI_HDRC_PAGE_SIZE; | |
| page &= ~TD_RESERVED_MASK; | |
| node->ptr->page[i] = cpu_to_le32(page); | |
| } | |
| } | |
| hwreq->req.actual += length; | |
| if (!list_empty(&hwreq->tds)) { | |
| /* get the last entry */ | |
| lastnode = list_entry(hwreq->tds.prev, | |
| struct td_node, td); | |
| lastnode->ptr->next = cpu_to_le32(node->dma); | |
| } | |
| INIT_LIST_HEAD(&node->td); | |
| list_add_tail(&node->td, &hwreq->tds); | |
| return 0; | |
| } | |
| /** | |
| * _usb_addr: calculates endpoint address from direction & number | |
| * @ep: endpoint | |
| */ | |
| static inline u8 _usb_addr(struct ci_hw_ep *ep) | |
| { | |
| return ((ep->dir == TX) ? USB_ENDPOINT_DIR_MASK : 0) | ep->num; | |
| } | |
| static int prepare_td_for_non_sg(struct ci_hw_ep *hwep, | |
| struct ci_hw_req *hwreq) | |
| { | |
| unsigned int rest = hwreq->req.length; | |
| int pages = TD_PAGE_COUNT; | |
| int ret = 0; | |
| if (rest == 0) { | |
| ret = add_td_to_list(hwep, hwreq, 0, NULL); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| /* | |
| * The first buffer could be not page aligned. | |
| * In that case we have to span into one extra td. | |
| */ | |
| if (hwreq->req.dma % PAGE_SIZE) | |
| pages--; | |
| while (rest > 0) { | |
| unsigned int count = min(hwreq->req.length - hwreq->req.actual, | |
| (unsigned int)(pages * CI_HDRC_PAGE_SIZE)); | |
| ret = add_td_to_list(hwep, hwreq, count, NULL); | |
| if (ret < 0) | |
| return ret; | |
| rest -= count; | |
| } | |
| if (hwreq->req.zero && hwreq->req.length && hwep->dir == TX | |
| && (hwreq->req.length % hwep->ep.maxpacket == 0)) { | |
| ret = add_td_to_list(hwep, hwreq, 0, NULL); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| return ret; | |
| } | |
| static int prepare_td_per_sg(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq, | |
| struct scatterlist *s) | |
| { | |
| unsigned int rest = sg_dma_len(s); | |
| int ret = 0; | |
| hwreq->req.actual = 0; | |
| while (rest > 0) { | |
| unsigned int count = min_t(unsigned int, rest, | |
| CI_MAX_BUF_SIZE); | |
| ret = add_td_to_list(hwep, hwreq, count, s); | |
| if (ret < 0) | |
| return ret; | |
| rest -= count; | |
| } | |
| return ret; | |
| } | |
| static void ci_add_buffer_entry(struct td_node *node, struct scatterlist *s) | |
| { | |
| int empty_td_slot_index = (CI_MAX_BUF_SIZE - node->td_remaining_size) | |
| / CI_HDRC_PAGE_SIZE; | |
| int i; | |
| u32 token; | |
| token = le32_to_cpu(node->ptr->token) + (sg_dma_len(s) << __ffs(TD_TOTAL_BYTES)); | |
| node->ptr->token = cpu_to_le32(token); | |
| for (i = empty_td_slot_index; i < TD_PAGE_COUNT; i++) { | |
| u32 page = (u32) sg_dma_address(s) + | |
| (i - empty_td_slot_index) * CI_HDRC_PAGE_SIZE; | |
| page &= ~TD_RESERVED_MASK; | |
| node->ptr->page[i] = cpu_to_le32(page); | |
| } | |
| } | |
| static int prepare_td_for_sg(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq) | |
| { | |
| struct usb_request *req = &hwreq->req; | |
| struct scatterlist *s = req->sg; | |
| int ret = 0, i = 0; | |
| struct td_node *node = NULL; | |
| if (!s || req->zero || req->length == 0) { | |
| dev_err(hwep->ci->dev, "not supported operation for sg\n"); | |
| return -EINVAL; | |
| } | |
| while (i++ < req->num_mapped_sgs) { | |
| if (sg_dma_address(s) % PAGE_SIZE) { | |
| dev_err(hwep->ci->dev, "not page aligned sg buffer\n"); | |
| return -EINVAL; | |
| } | |
| if (node && (node->td_remaining_size >= sg_dma_len(s))) { | |
| ci_add_buffer_entry(node, s); | |
| node->td_remaining_size -= sg_dma_len(s); | |
| } else { | |
| ret = prepare_td_per_sg(hwep, hwreq, s); | |
| if (ret) | |
| return ret; | |
| node = list_entry(hwreq->tds.prev, | |
| struct td_node, td); | |
| } | |
| s = sg_next(s); | |
| } | |
| return ret; | |
| } | |
| /* | |
| * Verify if the scatterlist is valid by iterating each sg entry. | |
| * Return invalid sg entry index which is less than num_sgs. | |
| */ | |
| static int sglist_get_invalid_entry(struct device *dma_dev, u8 dir, | |
| struct usb_request *req) | |
| { | |
| int i; | |
| struct scatterlist *s = req->sg; | |
| if (req->num_sgs == 1) | |
| return 1; | |
| dir = dir ? DMA_TO_DEVICE : DMA_FROM_DEVICE; | |
| for (i = 0; i < req->num_sgs; i++, s = sg_next(s)) { | |
| /* Only small sg (generally last sg) may be bounced. If | |
| * that happens. we can't ensure the addr is page-aligned | |
| * after dma map. | |
| */ | |
| if (dma_kmalloc_needs_bounce(dma_dev, s->length, dir)) | |
| break; | |
| /* Make sure each sg start address (except first sg) is | |
| * page-aligned and end address (except last sg) is also | |
| * page-aligned. | |
| */ | |
| if (i == 0) { | |
| if (!IS_ALIGNED(s->offset + s->length, | |
| CI_HDRC_PAGE_SIZE)) | |
| break; | |
| } else { | |
| if (s->offset) | |
| break; | |
| if (!sg_is_last(s) && !IS_ALIGNED(s->length, | |
| CI_HDRC_PAGE_SIZE)) | |
| break; | |
| } | |
| } | |
| return i; | |
| } | |
| static int sglist_do_bounce(struct ci_hw_req *hwreq, int index, | |
| bool copy, unsigned int *bounced) | |
| { | |
| void *buf; | |
| int i, ret, nents, num_sgs; | |
| unsigned int rest, rounded; | |
| struct scatterlist *sg, *src, *dst; | |
| nents = index + 1; | |
| ret = sg_alloc_table(&hwreq->sgt, nents, GFP_KERNEL); | |
| if (ret) | |
| return ret; | |
| sg = src = hwreq->req.sg; | |
| num_sgs = hwreq->req.num_sgs; | |
| rest = hwreq->req.length; | |
| dst = hwreq->sgt.sgl; | |
| for (i = 0; i < index; i++) { | |
| memcpy(dst, src, sizeof(*src)); | |
| rest -= src->length; | |
| src = sg_next(src); | |
| dst = sg_next(dst); | |
| } | |
| /* create one bounce buffer */ | |
| rounded = round_up(rest, CI_HDRC_PAGE_SIZE); | |
| buf = kmalloc(rounded, GFP_KERNEL); | |
| if (!buf) { | |
| sg_free_table(&hwreq->sgt); | |
| return -ENOMEM; | |
| } | |
| sg_set_buf(dst, buf, rounded); | |
| hwreq->req.sg = hwreq->sgt.sgl; | |
| hwreq->req.num_sgs = nents; | |
| hwreq->sgt.sgl = sg; | |
| hwreq->sgt.nents = num_sgs; | |
| if (copy) | |
| sg_copy_to_buffer(src, num_sgs - index, buf, rest); | |
| *bounced = rest; | |
| return 0; | |
| } | |
| static void sglist_do_debounce(struct ci_hw_req *hwreq, bool copy) | |
| { | |
| void *buf; | |
| int i, nents, num_sgs; | |
| struct scatterlist *sg, *src, *dst; | |
| sg = hwreq->req.sg; | |
| num_sgs = hwreq->req.num_sgs; | |
| src = sg_last(sg, num_sgs); | |
| buf = sg_virt(src); | |
| if (copy) { | |
| dst = hwreq->sgt.sgl; | |
| for (i = 0; i < num_sgs - 1; i++) | |
| dst = sg_next(dst); | |
| nents = hwreq->sgt.nents - num_sgs + 1; | |
| sg_copy_from_buffer(dst, nents, buf, sg_dma_len(src)); | |
| } | |
| hwreq->req.sg = hwreq->sgt.sgl; | |
| hwreq->req.num_sgs = hwreq->sgt.nents; | |
| hwreq->sgt.sgl = sg; | |
| hwreq->sgt.nents = num_sgs; | |
| kfree(buf); | |
| sg_free_table(&hwreq->sgt); | |
| } | |
| /** | |
| * _hardware_enqueue: configures a request at hardware level | |
| * @hwep: endpoint | |
| * @hwreq: request | |
| * | |
| * This function returns an error code | |
| */ | |
| static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq) | |
| { | |
| struct ci_hdrc *ci = hwep->ci; | |
| int ret = 0; | |
| struct td_node *firstnode, *lastnode; | |
| unsigned int bounced_size; | |
| struct scatterlist *sg; | |
| /* don't queue twice */ | |
| if (hwreq->req.status == -EALREADY) | |
| return -EALREADY; | |
| hwreq->req.status = -EALREADY; | |
| if (hwreq->req.num_sgs && hwreq->req.length && | |
| ci->has_short_pkt_limit) { | |
| ret = sglist_get_invalid_entry(ci->dev->parent, hwep->dir, | |
| &hwreq->req); | |
| if (ret < hwreq->req.num_sgs) { | |
| ret = sglist_do_bounce(hwreq, ret, hwep->dir == TX, | |
| &bounced_size); | |
| if (ret) | |
| return ret; | |
| } | |
| } | |
| ret = usb_gadget_map_request_by_dev(ci->dev->parent, | |
| &hwreq->req, hwep->dir); | |
| if (ret) | |
| return ret; | |
| if (hwreq->sgt.sgl) { | |
| /* We've mapped a bigger buffer, now recover the actual size */ | |
| sg = sg_last(hwreq->req.sg, hwreq->req.num_sgs); | |
| sg_dma_len(sg) = min(sg_dma_len(sg), bounced_size); | |
| } | |
| if (hwreq->req.num_mapped_sgs) | |
| ret = prepare_td_for_sg(hwep, hwreq); | |
| else | |
| ret = prepare_td_for_non_sg(hwep, hwreq); | |
| if (ret) | |
| return ret; | |
| lastnode = list_entry(hwreq->tds.prev, | |
| struct td_node, td); | |
| lastnode->ptr->next = cpu_to_le32(TD_TERMINATE); | |
| if (!hwreq->req.no_interrupt) | |
| lastnode->ptr->token |= cpu_to_le32(TD_IOC); | |
| list_for_each_entry_safe(firstnode, lastnode, &hwreq->tds, td) | |
| trace_ci_prepare_td(hwep, hwreq, firstnode); | |
| firstnode = list_first_entry(&hwreq->tds, struct td_node, td); | |
| wmb(); | |
| hwreq->req.actual = 0; | |
| if (!list_empty(&hwep->qh.queue)) { | |
| struct ci_hw_req *hwreqprev; | |
| int n = hw_ep_bit(hwep->num, hwep->dir); | |
| int tmp_stat; | |
| struct td_node *prevlastnode; | |
| u32 next = firstnode->dma & TD_ADDR_MASK; | |
| hwreqprev = list_entry(hwep->qh.queue.prev, | |
| struct ci_hw_req, queue); | |
| prevlastnode = list_entry(hwreqprev->tds.prev, | |
| struct td_node, td); | |
| prevlastnode->ptr->next = cpu_to_le32(next); | |
| wmb(); | |
| if (ci->rev == CI_REVISION_22) { | |
| if (!hw_read(ci, OP_ENDPTSTAT, BIT(n))) | |
| reprime_dtd(ci, hwep, prevlastnode); | |
| } | |
| if (hw_read(ci, OP_ENDPTPRIME, BIT(n))) | |
| goto done; | |
| do { | |
| hw_write(ci, OP_USBCMD, USBCMD_ATDTW, USBCMD_ATDTW); | |
| tmp_stat = hw_read(ci, OP_ENDPTSTAT, BIT(n)); | |
| } while (!hw_read(ci, OP_USBCMD, USBCMD_ATDTW) && tmp_stat); | |
| hw_write(ci, OP_USBCMD, USBCMD_ATDTW, 0); | |
| if (tmp_stat) | |
| goto done; | |
| /* OP_ENDPTSTAT will be clear by HW when the endpoint met | |
| * err. This dTD don't push to dQH if current dTD point is | |
| * not the last one in previous request. | |
| */ | |
| if (hwep->qh.ptr->curr != cpu_to_le32(prevlastnode->dma)) | |
| goto done; | |
| } | |
| /* QH configuration */ | |
| hwep->qh.ptr->td.next = cpu_to_le32(firstnode->dma); | |
| hwep->qh.ptr->td.token &= | |
| cpu_to_le32(~(TD_STATUS_HALTED|TD_STATUS_ACTIVE)); | |
| if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == RX) { | |
| u32 mul = hwreq->req.length / hwep->ep.maxpacket; | |
| if (hwreq->req.length == 0 | |
| || hwreq->req.length % hwep->ep.maxpacket) | |
| mul++; | |
| hwep->qh.ptr->cap |= cpu_to_le32(mul << __ffs(QH_MULT)); | |
| } | |
| ret = hw_ep_prime(ci, hwep->num, hwep->dir, | |
| hwep->type == USB_ENDPOINT_XFER_CONTROL); | |
| done: | |
| return ret; | |
| } | |
| /** | |
| * free_pending_td: remove a pending request for the endpoint | |
| * @hwep: endpoint | |
| */ | |
| static void free_pending_td(struct ci_hw_ep *hwep) | |
| { | |
| struct td_node *pending = hwep->pending_td; | |
| dma_pool_free(hwep->td_pool, pending->ptr, pending->dma); | |
| hwep->pending_td = NULL; | |
| kfree(pending); | |
| } | |
| static int reprime_dtd(struct ci_hdrc *ci, struct ci_hw_ep *hwep, | |
| struct td_node *node) | |
| { | |
| hwep->qh.ptr->td.next = cpu_to_le32(node->dma); | |
| hwep->qh.ptr->td.token &= | |
| cpu_to_le32(~(TD_STATUS_HALTED | TD_STATUS_ACTIVE)); | |
| return hw_ep_prime(ci, hwep->num, hwep->dir, | |
| hwep->type == USB_ENDPOINT_XFER_CONTROL); | |
| } | |
| /** | |
| * _hardware_dequeue: handles a request at hardware level | |
| * @hwep: endpoint | |
| * @hwreq: request | |
| * | |
| * This function returns an error code | |
| */ | |
| static int _hardware_dequeue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq) | |
| { | |
| u32 tmptoken; | |
| struct td_node *node, *tmpnode; | |
| unsigned remaining_length; | |
| unsigned actual = hwreq->req.length; | |
| struct ci_hdrc *ci = hwep->ci; | |
| bool is_isoc = hwep->type == USB_ENDPOINT_XFER_ISOC; | |
| if (hwreq->req.status != -EALREADY) | |
| return -EINVAL; | |
| hwreq->req.status = 0; | |
| list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | |
| tmptoken = le32_to_cpu(node->ptr->token); | |
| trace_ci_complete_td(hwep, hwreq, node); | |
| if ((TD_STATUS_ACTIVE & tmptoken) != 0) { | |
| int n = hw_ep_bit(hwep->num, hwep->dir); | |
| if (ci->rev == CI_REVISION_24 || | |
| ci->rev == CI_REVISION_22 || is_isoc) | |
| if (!hw_read(ci, OP_ENDPTSTAT, BIT(n))) | |
| reprime_dtd(ci, hwep, node); | |
| hwreq->req.status = -EALREADY; | |
| return -EBUSY; | |
| } | |
| remaining_length = (tmptoken & TD_TOTAL_BYTES); | |
| remaining_length >>= __ffs(TD_TOTAL_BYTES); | |
| actual -= remaining_length; | |
| hwreq->req.status = tmptoken & TD_STATUS; | |
| if ((TD_STATUS_HALTED & hwreq->req.status)) { | |
| hwreq->req.status = -EPIPE; | |
| break; | |
| } else if ((TD_STATUS_DT_ERR & hwreq->req.status)) { | |
| hwreq->req.status = -EPROTO; | |
| break; | |
| } else if ((TD_STATUS_TR_ERR & hwreq->req.status)) { | |
| if (is_isoc) { | |
| hwreq->req.status = 0; | |
| } else { | |
| hwreq->req.status = -EILSEQ; | |
| break; | |
| } | |
| } | |
| if (remaining_length && !is_isoc) { | |
| if (hwep->dir == TX) { | |
| hwreq->req.status = -EPROTO; | |
| break; | |
| } | |
| } | |
| /* | |
| * As the hardware could still address the freed td | |
| * which will run the udc unusable, the cleanup of the | |
| * td has to be delayed by one. | |
| */ | |
| if (hwep->pending_td) | |
| free_pending_td(hwep); | |
| hwep->pending_td = node; | |
| list_del_init(&node->td); | |
| } | |
| usb_gadget_unmap_request_by_dev(hwep->ci->dev->parent, | |
| &hwreq->req, hwep->dir); | |
| /* sglist bounced */ | |
| if (hwreq->sgt.sgl) | |
| sglist_do_debounce(hwreq, hwep->dir == RX); | |
| hwreq->req.actual += actual; | |
| if (hwreq->req.status) | |
| return hwreq->req.status; | |
| return hwreq->req.actual; | |
| } | |
| /** | |
| * _ep_nuke: dequeues all endpoint requests | |
| * @hwep: endpoint | |
| * | |
| * This function returns an error code | |
| * Caller must hold lock | |
| */ | |
| static int _ep_nuke(struct ci_hw_ep *hwep) | |
| __releases(hwep->lock) | |
| __acquires(hwep->lock) | |
| { | |
| struct td_node *node, *tmpnode; | |
| if (hwep == NULL) | |
| return -EINVAL; | |
| hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | |
| while (!list_empty(&hwep->qh.queue)) { | |
| /* pop oldest request */ | |
| struct ci_hw_req *hwreq = list_entry(hwep->qh.queue.next, | |
| struct ci_hw_req, queue); | |
| list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | |
| dma_pool_free(hwep->td_pool, node->ptr, node->dma); | |
| list_del_init(&node->td); | |
| node->ptr = NULL; | |
| kfree(node); | |
| } | |
| list_del_init(&hwreq->queue); | |
| hwreq->req.status = -ESHUTDOWN; | |
| /* Unmap DMA and clean up bounce buffers before giving back */ | |
| usb_gadget_unmap_request_by_dev(hwep->ci->dev->parent, | |
| &hwreq->req, hwep->dir); | |
| if (hwreq->sgt.sgl) | |
| sglist_do_debounce(hwreq, false); | |
| if (hwreq->req.complete != NULL) { | |
| spin_unlock(hwep->lock); | |
| usb_gadget_giveback_request(&hwep->ep, &hwreq->req); | |
| spin_lock(hwep->lock); | |
| } | |
| } | |
| if (hwep->pending_td) | |
| free_pending_td(hwep); | |
| return 0; | |
| } | |
| static int _ep_set_halt(struct usb_ep *ep, int value, bool check_transfer) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| int direction, retval = 0; | |
| unsigned long flags; | |
| if (ep == NULL || hwep->ep.desc == NULL) | |
| return -EINVAL; | |
| if (usb_endpoint_xfer_isoc(hwep->ep.desc)) | |
| return -EOPNOTSUPP; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| if (value && hwep->dir == TX && check_transfer && | |
| !list_empty(&hwep->qh.queue) && | |
| !usb_endpoint_xfer_control(hwep->ep.desc)) { | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return -EAGAIN; | |
| } | |
| direction = hwep->dir; | |
| do { | |
| retval |= hw_ep_set_halt(hwep->ci, hwep->num, hwep->dir, value); | |
| if (!value) | |
| hwep->wedge = 0; | |
| if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | |
| hwep->dir = (hwep->dir == TX) ? RX : TX; | |
| } while (hwep->dir != direction); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return retval; | |
| } | |
| /** | |
| * _gadget_stop_activity: stops all USB activity, flushes & disables all endpts | |
| * @gadget: gadget | |
| * | |
| * This function returns an error code | |
| */ | |
| static int _gadget_stop_activity(struct usb_gadget *gadget) | |
| { | |
| struct usb_ep *ep; | |
| struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | |
| unsigned long flags; | |
| /* flush all endpoints */ | |
| gadget_for_each_ep(ep, gadget) { | |
| usb_ep_fifo_flush(ep); | |
| } | |
| usb_ep_fifo_flush(&ci->ep0out->ep); | |
| usb_ep_fifo_flush(&ci->ep0in->ep); | |
| /* make sure to disable all endpoints */ | |
| gadget_for_each_ep(ep, gadget) { | |
| usb_ep_disable(ep); | |
| } | |
| if (ci->status != NULL) { | |
| usb_ep_free_request(&ci->ep0in->ep, ci->status); | |
| ci->status = NULL; | |
| } | |
| spin_lock_irqsave(&ci->lock, flags); | |
| ci->gadget.speed = USB_SPEED_UNKNOWN; | |
| ci->remote_wakeup = 0; | |
| ci->suspended = 0; | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| return 0; | |
| } | |
| /****************************************************************************** | |
| * ISR block | |
| *****************************************************************************/ | |
| /** | |
| * isr_reset_handler: USB reset interrupt handler | |
| * @ci: UDC device | |
| * | |
| * This function resets USB engine after a bus reset occurred | |
| */ | |
| static void isr_reset_handler(struct ci_hdrc *ci) | |
| __releases(ci->lock) | |
| __acquires(ci->lock) | |
| { | |
| int retval; | |
| u32 intr; | |
| spin_unlock(&ci->lock); | |
| if (ci->gadget.speed != USB_SPEED_UNKNOWN) | |
| usb_gadget_udc_reset(&ci->gadget, ci->driver); | |
| retval = _gadget_stop_activity(&ci->gadget); | |
| if (retval) | |
| goto done; | |
| retval = hw_usb_reset(ci); | |
| if (retval) | |
| goto done; | |
| /* clear SLI */ | |
| hw_write(ci, OP_USBSTS, USBi_SLI, USBi_SLI); | |
| intr = hw_read(ci, OP_USBINTR, ~0); | |
| hw_write(ci, OP_USBINTR, ~0, intr | USBi_SLI); | |
| ci->status = usb_ep_alloc_request(&ci->ep0in->ep, GFP_ATOMIC); | |
| if (ci->status == NULL) | |
| retval = -ENOMEM; | |
| done: | |
| spin_lock(&ci->lock); | |
| if (retval) | |
| dev_err(ci->dev, "error: %i\n", retval); | |
| } | |
| /** | |
| * isr_get_status_complete: get_status request complete function | |
| * @ep: endpoint | |
| * @req: request handled | |
| * | |
| * Caller must release lock | |
| */ | |
| static void isr_get_status_complete(struct usb_ep *ep, struct usb_request *req) | |
| { | |
| if (ep == NULL || req == NULL) | |
| return; | |
| kfree(req->buf); | |
| usb_ep_free_request(ep, req); | |
| } | |
| /** | |
| * _ep_queue: queues (submits) an I/O request to an endpoint | |
| * @ep: endpoint | |
| * @req: request | |
| * @gfp_flags: GFP flags (not used) | |
| * | |
| * Caller must hold lock | |
| * This function returns an error code | |
| */ | |
| static int _ep_queue(struct usb_ep *ep, struct usb_request *req, | |
| gfp_t __maybe_unused gfp_flags) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | |
| struct ci_hdrc *ci = hwep->ci; | |
| int retval = 0; | |
| if (ep == NULL || req == NULL || hwep->ep.desc == NULL) | |
| return -EINVAL; | |
| if (hwep->type == USB_ENDPOINT_XFER_CONTROL) { | |
| if (req->length) | |
| hwep = (ci->ep0_dir == RX) ? | |
| ci->ep0out : ci->ep0in; | |
| if (!list_empty(&hwep->qh.queue)) { | |
| _ep_nuke(hwep); | |
| dev_warn(hwep->ci->dev, "endpoint ctrl %X nuked\n", | |
| _usb_addr(hwep)); | |
| } | |
| } | |
| if (usb_endpoint_xfer_isoc(hwep->ep.desc) && | |
| hwreq->req.length > hwep->ep.mult * hwep->ep.maxpacket) { | |
| dev_err(hwep->ci->dev, "request length too big for isochronous\n"); | |
| return -EMSGSIZE; | |
| } | |
| if (ci->has_short_pkt_limit && | |
| hwreq->req.length > CI_MAX_REQ_SIZE) { | |
| dev_err(hwep->ci->dev, "request length too big (max 16KB)\n"); | |
| return -EMSGSIZE; | |
| } | |
| /* first nuke then test link, e.g. previous status has not sent */ | |
| if (!list_empty(&hwreq->queue)) { | |
| dev_err(hwep->ci->dev, "request already in queue\n"); | |
| return -EBUSY; | |
| } | |
| /* push request */ | |
| hwreq->req.status = -EINPROGRESS; | |
| hwreq->req.actual = 0; | |
| retval = _hardware_enqueue(hwep, hwreq); | |
| if (retval == -EALREADY) | |
| retval = 0; | |
| if (!retval) | |
| list_add_tail(&hwreq->queue, &hwep->qh.queue); | |
| return retval; | |
| } | |
| /** | |
| * isr_get_status_response: get_status request response | |
| * @ci: ci struct | |
| * @setup: setup request packet | |
| * | |
| * This function returns an error code | |
| */ | |
| static int isr_get_status_response(struct ci_hdrc *ci, | |
| struct usb_ctrlrequest *setup) | |
| __releases(hwep->lock) | |
| __acquires(hwep->lock) | |
| { | |
| struct ci_hw_ep *hwep = ci->ep0in; | |
| struct usb_request *req = NULL; | |
| gfp_t gfp_flags = GFP_ATOMIC; | |
| int dir, num, retval; | |
| if (hwep == NULL || setup == NULL) | |
| return -EINVAL; | |
| spin_unlock(hwep->lock); | |
| req = usb_ep_alloc_request(&hwep->ep, gfp_flags); | |
| spin_lock(hwep->lock); | |
| if (req == NULL) | |
| return -ENOMEM; | |
| req->complete = isr_get_status_complete; | |
| req->length = 2; | |
| req->buf = kzalloc(req->length, gfp_flags); | |
| if (req->buf == NULL) { | |
| retval = -ENOMEM; | |
| goto err_free_req; | |
| } | |
| if ((setup->bRequestType & USB_RECIP_MASK) == USB_RECIP_DEVICE) { | |
| *(u16 *)req->buf = (ci->remote_wakeup << 1) | | |
| ci->gadget.is_selfpowered; | |
| } else if ((setup->bRequestType & USB_RECIP_MASK) \ | |
| == USB_RECIP_ENDPOINT) { | |
| dir = (le16_to_cpu(setup->wIndex) & USB_ENDPOINT_DIR_MASK) ? | |
| TX : RX; | |
| num = le16_to_cpu(setup->wIndex) & USB_ENDPOINT_NUMBER_MASK; | |
| *(u16 *)req->buf = hw_ep_get_halt(ci, num, dir); | |
| } | |
| /* else do nothing; reserved for future use */ | |
| retval = _ep_queue(&hwep->ep, req, gfp_flags); | |
| if (retval) | |
| goto err_free_buf; | |
| return 0; | |
| err_free_buf: | |
| kfree(req->buf); | |
| err_free_req: | |
| spin_unlock(hwep->lock); | |
| usb_ep_free_request(&hwep->ep, req); | |
| spin_lock(hwep->lock); | |
| return retval; | |
| } | |
| /** | |
| * isr_setup_status_complete: setup_status request complete function | |
| * @ep: endpoint | |
| * @req: request handled | |
| * | |
| * Caller must release lock. Put the port in test mode if test mode | |
| * feature is selected. | |
| */ | |
| static void | |
| isr_setup_status_complete(struct usb_ep *ep, struct usb_request *req) | |
| { | |
| struct ci_hdrc *ci = req->context; | |
| unsigned long flags; | |
| if (req->status < 0) | |
| return; | |
| if (ci->setaddr) { | |
| hw_usb_set_address(ci, ci->address); | |
| ci->setaddr = false; | |
| if (ci->address) | |
| usb_gadget_set_state(&ci->gadget, USB_STATE_ADDRESS); | |
| } | |
| spin_lock_irqsave(&ci->lock, flags); | |
| if (ci->test_mode) | |
| hw_port_test_set(ci, ci->test_mode); | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| } | |
| /** | |
| * isr_setup_status_phase: queues the status phase of a setup transation | |
| * @ci: ci struct | |
| * | |
| * This function returns an error code | |
| */ | |
| static int isr_setup_status_phase(struct ci_hdrc *ci) | |
| { | |
| struct ci_hw_ep *hwep; | |
| /* | |
| * Unexpected USB controller behavior, caused by bad signal integrity | |
| * or ground reference problems, can lead to isr_setup_status_phase | |
| * being called with ci->status equal to NULL. | |
| * If this situation occurs, you should review your USB hardware design. | |
| */ | |
| if (WARN_ON_ONCE(!ci->status)) | |
| return -EPIPE; | |
| hwep = (ci->ep0_dir == TX) ? ci->ep0out : ci->ep0in; | |
| ci->status->context = ci; | |
| ci->status->complete = isr_setup_status_complete; | |
| return _ep_queue(&hwep->ep, ci->status, GFP_ATOMIC); | |
| } | |
| /** | |
| * isr_tr_complete_low: transaction complete low level handler | |
| * @hwep: endpoint | |
| * | |
| * This function returns an error code | |
| * Caller must hold lock | |
| */ | |
| static int isr_tr_complete_low(struct ci_hw_ep *hwep) | |
| __releases(hwep->lock) | |
| __acquires(hwep->lock) | |
| { | |
| struct ci_hw_req *hwreq, *hwreqtemp; | |
| struct ci_hw_ep *hweptemp = hwep; | |
| int retval = 0; | |
| list_for_each_entry_safe(hwreq, hwreqtemp, &hwep->qh.queue, | |
| queue) { | |
| retval = _hardware_dequeue(hwep, hwreq); | |
| if (retval < 0) | |
| break; | |
| list_del_init(&hwreq->queue); | |
| if (hwreq->req.complete != NULL) { | |
| spin_unlock(hwep->lock); | |
| if ((hwep->type == USB_ENDPOINT_XFER_CONTROL) && | |
| hwreq->req.length) | |
| hweptemp = hwep->ci->ep0in; | |
| usb_gadget_giveback_request(&hweptemp->ep, &hwreq->req); | |
| spin_lock(hwep->lock); | |
| } | |
| } | |
| if (retval == -EBUSY) | |
| retval = 0; | |
| return retval; | |
| } | |
| static int otg_a_alt_hnp_support(struct ci_hdrc *ci) | |
| { | |
| dev_warn(&ci->gadget.dev, | |
| "connect the device to an alternate port if you want HNP\n"); | |
| return isr_setup_status_phase(ci); | |
| } | |
| /** | |
| * isr_setup_packet_handler: setup packet handler | |
| * @ci: UDC descriptor | |
| * | |
| * This function handles setup packet | |
| */ | |
| static void isr_setup_packet_handler(struct ci_hdrc *ci) | |
| __releases(ci->lock) | |
| __acquires(ci->lock) | |
| { | |
| struct ci_hw_ep *hwep = &ci->ci_hw_ep[0]; | |
| struct usb_ctrlrequest req; | |
| int type, num, dir, err = -EINVAL; | |
| u8 tmode = 0; | |
| /* | |
| * Flush data and handshake transactions of previous | |
| * setup packet. | |
| */ | |
| _ep_nuke(ci->ep0out); | |
| _ep_nuke(ci->ep0in); | |
| /* read_setup_packet */ | |
| do { | |
| hw_test_and_set_setup_guard(ci); | |
| memcpy(&req, &hwep->qh.ptr->setup, sizeof(req)); | |
| } while (!hw_test_and_clear_setup_guard(ci)); | |
| type = req.bRequestType; | |
| ci->ep0_dir = (type & USB_DIR_IN) ? TX : RX; | |
| switch (req.bRequest) { | |
| case USB_REQ_CLEAR_FEATURE: | |
| if (type == (USB_DIR_OUT|USB_RECIP_ENDPOINT) && | |
| le16_to_cpu(req.wValue) == | |
| USB_ENDPOINT_HALT) { | |
| if (req.wLength != 0) | |
| break; | |
| num = le16_to_cpu(req.wIndex); | |
| dir = (num & USB_ENDPOINT_DIR_MASK) ? TX : RX; | |
| num &= USB_ENDPOINT_NUMBER_MASK; | |
| if (dir == TX) | |
| num += ci->hw_ep_max / 2; | |
| if (!ci->ci_hw_ep[num].wedge) { | |
| spin_unlock(&ci->lock); | |
| err = usb_ep_clear_halt( | |
| &ci->ci_hw_ep[num].ep); | |
| spin_lock(&ci->lock); | |
| if (err) | |
| break; | |
| } | |
| err = isr_setup_status_phase(ci); | |
| } else if (type == (USB_DIR_OUT|USB_RECIP_DEVICE) && | |
| le16_to_cpu(req.wValue) == | |
| USB_DEVICE_REMOTE_WAKEUP) { | |
| if (req.wLength != 0) | |
| break; | |
| ci->remote_wakeup = 0; | |
| err = isr_setup_status_phase(ci); | |
| } else { | |
| goto delegate; | |
| } | |
| break; | |
| case USB_REQ_GET_STATUS: | |
| if ((type != (USB_DIR_IN|USB_RECIP_DEVICE) || | |
| le16_to_cpu(req.wIndex) == OTG_STS_SELECTOR) && | |
| type != (USB_DIR_IN|USB_RECIP_ENDPOINT) && | |
| type != (USB_DIR_IN|USB_RECIP_INTERFACE)) | |
| goto delegate; | |
| if (le16_to_cpu(req.wLength) != 2 || | |
| le16_to_cpu(req.wValue) != 0) | |
| break; | |
| err = isr_get_status_response(ci, &req); | |
| break; | |
| case USB_REQ_SET_ADDRESS: | |
| if (type != (USB_DIR_OUT|USB_RECIP_DEVICE)) | |
| goto delegate; | |
| if (le16_to_cpu(req.wLength) != 0 || | |
| le16_to_cpu(req.wIndex) != 0) | |
| break; | |
| ci->address = (u8)le16_to_cpu(req.wValue); | |
| ci->setaddr = true; | |
| err = isr_setup_status_phase(ci); | |
| break; | |
| case USB_REQ_SET_FEATURE: | |
| if (type == (USB_DIR_OUT|USB_RECIP_ENDPOINT) && | |
| le16_to_cpu(req.wValue) == | |
| USB_ENDPOINT_HALT) { | |
| if (req.wLength != 0) | |
| break; | |
| num = le16_to_cpu(req.wIndex); | |
| dir = (num & USB_ENDPOINT_DIR_MASK) ? TX : RX; | |
| num &= USB_ENDPOINT_NUMBER_MASK; | |
| if (dir == TX) | |
| num += ci->hw_ep_max / 2; | |
| spin_unlock(&ci->lock); | |
| err = _ep_set_halt(&ci->ci_hw_ep[num].ep, 1, false); | |
| spin_lock(&ci->lock); | |
| if (!err) | |
| isr_setup_status_phase(ci); | |
| } else if (type == (USB_DIR_OUT|USB_RECIP_DEVICE)) { | |
| if (req.wLength != 0) | |
| break; | |
| switch (le16_to_cpu(req.wValue)) { | |
| case USB_DEVICE_REMOTE_WAKEUP: | |
| ci->remote_wakeup = 1; | |
| err = isr_setup_status_phase(ci); | |
| break; | |
| case USB_DEVICE_TEST_MODE: | |
| tmode = le16_to_cpu(req.wIndex) >> 8; | |
| switch (tmode) { | |
| case USB_TEST_J: | |
| case USB_TEST_K: | |
| case USB_TEST_SE0_NAK: | |
| case USB_TEST_PACKET: | |
| case USB_TEST_FORCE_ENABLE: | |
| ci->test_mode = tmode; | |
| err = isr_setup_status_phase( | |
| ci); | |
| break; | |
| default: | |
| break; | |
| } | |
| break; | |
| case USB_DEVICE_B_HNP_ENABLE: | |
| if (ci_otg_is_fsm_mode(ci)) { | |
| ci->gadget.b_hnp_enable = 1; | |
| err = isr_setup_status_phase( | |
| ci); | |
| } | |
| break; | |
| case USB_DEVICE_A_ALT_HNP_SUPPORT: | |
| if (ci_otg_is_fsm_mode(ci)) | |
| err = otg_a_alt_hnp_support(ci); | |
| break; | |
| case USB_DEVICE_A_HNP_SUPPORT: | |
| if (ci_otg_is_fsm_mode(ci)) { | |
| ci->gadget.a_hnp_support = 1; | |
| err = isr_setup_status_phase( | |
| ci); | |
| } | |
| break; | |
| default: | |
| goto delegate; | |
| } | |
| } else { | |
| goto delegate; | |
| } | |
| break; | |
| default: | |
| delegate: | |
| if (req.wLength == 0) /* no data phase */ | |
| ci->ep0_dir = TX; | |
| spin_unlock(&ci->lock); | |
| err = ci->driver->setup(&ci->gadget, &req); | |
| spin_lock(&ci->lock); | |
| break; | |
| } | |
| if (err < 0) { | |
| spin_unlock(&ci->lock); | |
| if (_ep_set_halt(&hwep->ep, 1, false)) | |
| dev_err(ci->dev, "error: _ep_set_halt\n"); | |
| spin_lock(&ci->lock); | |
| } | |
| } | |
| /** | |
| * isr_tr_complete_handler: transaction complete interrupt handler | |
| * @ci: UDC descriptor | |
| * | |
| * This function handles traffic events | |
| */ | |
| static void isr_tr_complete_handler(struct ci_hdrc *ci) | |
| __releases(ci->lock) | |
| __acquires(ci->lock) | |
| { | |
| unsigned i; | |
| int err; | |
| for (i = 0; i < ci->hw_ep_max; i++) { | |
| struct ci_hw_ep *hwep = &ci->ci_hw_ep[i]; | |
| if (hwep->ep.desc == NULL) | |
| continue; /* not configured */ | |
| if (hw_test_and_clear_complete(ci, i)) { | |
| err = isr_tr_complete_low(hwep); | |
| if (hwep->type == USB_ENDPOINT_XFER_CONTROL) { | |
| if (err > 0) /* needs status phase */ | |
| err = isr_setup_status_phase(ci); | |
| if (err < 0) { | |
| spin_unlock(&ci->lock); | |
| if (_ep_set_halt(&hwep->ep, 1, false)) | |
| dev_err(ci->dev, | |
| "error: _ep_set_halt\n"); | |
| spin_lock(&ci->lock); | |
| } | |
| } | |
| } | |
| /* Only handle setup packet below */ | |
| if (i == 0 && | |
| hw_test_and_clear(ci, OP_ENDPTSETUPSTAT, BIT(0))) | |
| isr_setup_packet_handler(ci); | |
| } | |
| } | |
| /****************************************************************************** | |
| * ENDPT block | |
| *****************************************************************************/ | |
| /* | |
| * ep_enable: configure endpoint, making it usable | |
| * | |
| * Check usb_ep_enable() at "usb_gadget.h" for details | |
| */ | |
| static int ep_enable(struct usb_ep *ep, | |
| const struct usb_endpoint_descriptor *desc) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| int retval = 0; | |
| unsigned long flags; | |
| u32 cap = 0; | |
| if (ep == NULL || desc == NULL) | |
| return -EINVAL; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| /* only internal SW should enable ctrl endpts */ | |
| if (!list_empty(&hwep->qh.queue)) { | |
| dev_warn(hwep->ci->dev, "enabling a non-empty endpoint!\n"); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return -EBUSY; | |
| } | |
| hwep->ep.desc = desc; | |
| hwep->dir = usb_endpoint_dir_in(desc) ? TX : RX; | |
| hwep->num = usb_endpoint_num(desc); | |
| hwep->type = usb_endpoint_type(desc); | |
| hwep->ep.maxpacket = usb_endpoint_maxp(desc); | |
| hwep->ep.mult = usb_endpoint_maxp_mult(desc); | |
| if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | |
| cap |= QH_IOS; | |
| cap |= QH_ZLT; | |
| cap |= (hwep->ep.maxpacket << __ffs(QH_MAX_PKT)) & QH_MAX_PKT; | |
| /* | |
| * For ISO-TX, we set mult at QH as the largest value, and use | |
| * MultO at TD as real mult value. | |
| */ | |
| if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == TX) | |
| cap |= 3 << __ffs(QH_MULT); | |
| hwep->qh.ptr->cap = cpu_to_le32(cap); | |
| hwep->qh.ptr->td.next |= cpu_to_le32(TD_TERMINATE); /* needed? */ | |
| if (hwep->num != 0 && hwep->type == USB_ENDPOINT_XFER_CONTROL) { | |
| dev_err(hwep->ci->dev, "Set control xfer at non-ep0\n"); | |
| retval = -EINVAL; | |
| } | |
| /* | |
| * Enable endpoints in the HW other than ep0 as ep0 | |
| * is always enabled | |
| */ | |
| if (hwep->num) | |
| retval |= hw_ep_enable(hwep->ci, hwep->num, hwep->dir, | |
| hwep->type); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return retval; | |
| } | |
| /* | |
| * ep_disable: endpoint is no longer usable | |
| * | |
| * Check usb_ep_disable() at "usb_gadget.h" for details | |
| */ | |
| static int ep_disable(struct usb_ep *ep) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| int direction, retval = 0; | |
| unsigned long flags; | |
| if (ep == NULL) | |
| return -EINVAL; | |
| else if (hwep->ep.desc == NULL) | |
| return -EBUSY; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return 0; | |
| } | |
| /* only internal SW should disable ctrl endpts */ | |
| direction = hwep->dir; | |
| do { | |
| retval |= _ep_nuke(hwep); | |
| retval |= hw_ep_disable(hwep->ci, hwep->num, hwep->dir); | |
| if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | |
| hwep->dir = (hwep->dir == TX) ? RX : TX; | |
| } while (hwep->dir != direction); | |
| hwep->ep.desc = NULL; | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return retval; | |
| } | |
| /* | |
| * ep_alloc_request: allocate a request object to use with this endpoint | |
| * | |
| * Check usb_ep_alloc_request() at "usb_gadget.h" for details | |
| */ | |
| static struct usb_request *ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) | |
| { | |
| struct ci_hw_req *hwreq; | |
| if (ep == NULL) | |
| return NULL; | |
| hwreq = kzalloc_obj(struct ci_hw_req, gfp_flags); | |
| if (hwreq != NULL) { | |
| INIT_LIST_HEAD(&hwreq->queue); | |
| INIT_LIST_HEAD(&hwreq->tds); | |
| } | |
| return (hwreq == NULL) ? NULL : &hwreq->req; | |
| } | |
| /* | |
| * ep_free_request: frees a request object | |
| * | |
| * Check usb_ep_free_request() at "usb_gadget.h" for details | |
| */ | |
| static void ep_free_request(struct usb_ep *ep, struct usb_request *req) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | |
| struct td_node *node, *tmpnode; | |
| unsigned long flags; | |
| if (ep == NULL || req == NULL) { | |
| return; | |
| } else if (!list_empty(&hwreq->queue)) { | |
| dev_err(hwep->ci->dev, "freeing queued request\n"); | |
| return; | |
| } | |
| spin_lock_irqsave(hwep->lock, flags); | |
| list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | |
| dma_pool_free(hwep->td_pool, node->ptr, node->dma); | |
| list_del_init(&node->td); | |
| node->ptr = NULL; | |
| kfree(node); | |
| } | |
| kfree(hwreq); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| } | |
| /* | |
| * ep_queue: queues (submits) an I/O request to an endpoint | |
| * | |
| * Check usb_ep_queue()* at usb_gadget.h" for details | |
| */ | |
| static int ep_queue(struct usb_ep *ep, struct usb_request *req, | |
| gfp_t __maybe_unused gfp_flags) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| int retval = 0; | |
| unsigned long flags; | |
| if (ep == NULL || req == NULL || hwep->ep.desc == NULL) | |
| return -EINVAL; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return 0; | |
| } | |
| retval = _ep_queue(ep, req, gfp_flags); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return retval; | |
| } | |
| /* | |
| * ep_dequeue: dequeues (cancels, unlinks) an I/O request from an endpoint | |
| * | |
| * Check usb_ep_dequeue() at "usb_gadget.h" for details | |
| */ | |
| static int ep_dequeue(struct usb_ep *ep, struct usb_request *req) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | |
| unsigned long flags; | |
| struct td_node *node, *tmpnode; | |
| if (ep == NULL || req == NULL || hwreq->req.status != -EALREADY || | |
| hwep->ep.desc == NULL || list_empty(&hwreq->queue) || | |
| list_empty(&hwep->qh.queue)) | |
| return -EINVAL; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| if (hwep->ci->gadget.speed != USB_SPEED_UNKNOWN) | |
| hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | |
| list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | |
| dma_pool_free(hwep->td_pool, node->ptr, node->dma); | |
| list_del(&node->td); | |
| kfree(node); | |
| } | |
| /* pop request */ | |
| list_del_init(&hwreq->queue); | |
| usb_gadget_unmap_request(&hwep->ci->gadget, req, hwep->dir); | |
| if (hwreq->sgt.sgl) | |
| sglist_do_debounce(hwreq, false); | |
| req->status = -ECONNRESET; | |
| if (hwreq->req.complete != NULL) { | |
| spin_unlock(hwep->lock); | |
| usb_gadget_giveback_request(&hwep->ep, &hwreq->req); | |
| spin_lock(hwep->lock); | |
| } | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return 0; | |
| } | |
| /* | |
| * ep_set_halt: sets the endpoint halt feature | |
| * | |
| * Check usb_ep_set_halt() at "usb_gadget.h" for details | |
| */ | |
| static int ep_set_halt(struct usb_ep *ep, int value) | |
| { | |
| return _ep_set_halt(ep, value, true); | |
| } | |
| /* | |
| * ep_set_wedge: sets the halt feature and ignores clear requests | |
| * | |
| * Check usb_ep_set_wedge() at "usb_gadget.h" for details | |
| */ | |
| static int ep_set_wedge(struct usb_ep *ep) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| unsigned long flags; | |
| if (ep == NULL || hwep->ep.desc == NULL) | |
| return -EINVAL; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| hwep->wedge = 1; | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return usb_ep_set_halt(ep); | |
| } | |
| /* | |
| * ep_fifo_flush: flushes contents of a fifo | |
| * | |
| * Check usb_ep_fifo_flush() at "usb_gadget.h" for details | |
| */ | |
| static void ep_fifo_flush(struct usb_ep *ep) | |
| { | |
| struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | |
| unsigned long flags; | |
| if (ep == NULL) { | |
| dev_err(hwep->ci->dev, "%02X: -EINVAL\n", _usb_addr(hwep)); | |
| return; | |
| } | |
| spin_lock_irqsave(hwep->lock, flags); | |
| if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return; | |
| } | |
| hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| } | |
| /* | |
| * Endpoint-specific part of the API to the USB controller hardware | |
| * Check "usb_gadget.h" for details | |
| */ | |
| static const struct usb_ep_ops usb_ep_ops = { | |
| .enable = ep_enable, | |
| .disable = ep_disable, | |
| .alloc_request = ep_alloc_request, | |
| .free_request = ep_free_request, | |
| .queue = ep_queue, | |
| .dequeue = ep_dequeue, | |
| .set_halt = ep_set_halt, | |
| .set_wedge = ep_set_wedge, | |
| .fifo_flush = ep_fifo_flush, | |
| }; | |
| /****************************************************************************** | |
| * GADGET block | |
| *****************************************************************************/ | |
| static void ci_udc_enable_vbus_irq(struct ci_hdrc *ci, bool enable) | |
| { | |
| u32 reg = OTGSC_BSVIS; | |
| if (!ci->is_otg) | |
| return; | |
| if (enable) | |
| reg |= OTGSC_BSVIE; | |
| /* Clear pending BSVIS and enable/disable BSVIE */ | |
| hw_write_otgsc(ci, OTGSC_BSVIE | OTGSC_BSVIS, reg); | |
| } | |
| static int ci_udc_get_frame(struct usb_gadget *_gadget) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| unsigned long flags; | |
| int ret; | |
| spin_lock_irqsave(&ci->lock, flags); | |
| ret = hw_read(ci, OP_FRINDEX, 0x3fff); | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| return ret >> 3; | |
| } | |
| /* | |
| * ci_hdrc_gadget_connect: caller makes sure gadget driver is binded | |
| */ | |
| static void ci_hdrc_gadget_connect(struct usb_gadget *_gadget, int is_active) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| if (is_active) { | |
| pm_runtime_get_sync(ci->dev); | |
| hw_device_reset(ci); | |
| spin_lock_irq(&ci->lock); | |
| if (ci->driver) { | |
| hw_device_state(ci, ci->ep0out->qh.dma); | |
| usb_gadget_set_state(_gadget, USB_STATE_POWERED); | |
| spin_unlock_irq(&ci->lock); | |
| usb_udc_vbus_handler(_gadget, true); | |
| } else { | |
| spin_unlock_irq(&ci->lock); | |
| } | |
| } else { | |
| usb_udc_vbus_handler(_gadget, false); | |
| if (ci->driver) | |
| ci->driver->disconnect(&ci->gadget); | |
| hw_device_state(ci, 0); | |
| if (ci->platdata->notify_event) | |
| ci->platdata->notify_event(ci, | |
| CI_HDRC_CONTROLLER_STOPPED_EVENT); | |
| _gadget_stop_activity(&ci->gadget); | |
| pm_runtime_put_sync(ci->dev); | |
| usb_gadget_set_state(_gadget, USB_STATE_NOTATTACHED); | |
| } | |
| } | |
| static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| unsigned long flags; | |
| int ret = 0; | |
| spin_lock_irqsave(&ci->lock, flags); | |
| ci->vbus_active = is_active; | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| if (ci->usb_phy) | |
| usb_phy_set_charger_state(ci->usb_phy, is_active ? | |
| USB_CHARGER_PRESENT : USB_CHARGER_ABSENT); | |
| if (ci->platdata->notify_event) | |
| ret = ci->platdata->notify_event(ci, | |
| CI_HDRC_CONTROLLER_VBUS_EVENT); | |
| if (ci->usb_phy) { | |
| if (is_active) | |
| usb_phy_set_event(ci->usb_phy, USB_EVENT_VBUS); | |
| else | |
| usb_phy_set_event(ci->usb_phy, USB_EVENT_NONE); | |
| } | |
| if (ci->driver) | |
| ci_hdrc_gadget_connect(_gadget, is_active); | |
| return ret; | |
| } | |
| static int ci_udc_wakeup(struct usb_gadget *_gadget) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| unsigned long flags; | |
| int ret = 0; | |
| spin_lock_irqsave(&ci->lock, flags); | |
| if (ci->gadget.speed == USB_SPEED_UNKNOWN) { | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| return 0; | |
| } | |
| if (!ci->remote_wakeup) { | |
| ret = -EOPNOTSUPP; | |
| goto out; | |
| } | |
| if (!hw_read(ci, OP_PORTSC, PORTSC_SUSP)) { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| hw_write(ci, OP_PORTSC, PORTSC_FPR, PORTSC_FPR); | |
| out: | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| return ret; | |
| } | |
| static int ci_udc_vbus_draw(struct usb_gadget *_gadget, unsigned ma) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| if (ci->usb_phy) | |
| return usb_phy_set_power(ci->usb_phy, ma); | |
| return -ENOTSUPP; | |
| } | |
| static int ci_udc_selfpowered(struct usb_gadget *_gadget, int is_on) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| struct ci_hw_ep *hwep = ci->ep0in; | |
| unsigned long flags; | |
| spin_lock_irqsave(hwep->lock, flags); | |
| _gadget->is_selfpowered = (is_on != 0); | |
| spin_unlock_irqrestore(hwep->lock, flags); | |
| return 0; | |
| } | |
| /* Change Data+ pullup status | |
| * this func is used by usb_gadget_connect/disconnect | |
| */ | |
| static int ci_udc_pullup(struct usb_gadget *_gadget, int is_on) | |
| { | |
| struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | |
| /* | |
| * Data+ pullup controlled by OTG state machine in OTG fsm mode; | |
| * and don't touch Data+ in host mode for dual role config. | |
| */ | |
| if (ci_otg_is_fsm_mode(ci) || ci->role == CI_ROLE_HOST) | |
| return 0; | |
| pm_runtime_get_sync(ci->dev); | |
| if (is_on) | |
| hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS); | |
| else | |
| hw_write(ci, OP_USBCMD, USBCMD_RS, 0); | |
| if (ci->platdata->notify_event) { | |
| _gadget->connected = is_on; | |
| ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_PULLUP_EVENT); | |
| } | |
| pm_runtime_put_sync(ci->dev); | |
| return 0; | |
| } | |
| static int ci_udc_start(struct usb_gadget *gadget, | |
| struct usb_gadget_driver *driver); | |
| static int ci_udc_stop(struct usb_gadget *gadget); | |
| /* Match ISOC IN from the highest endpoint */ | |
| static struct usb_ep *ci_udc_match_ep(struct usb_gadget *gadget, | |
| struct usb_endpoint_descriptor *desc, | |
| struct usb_ss_ep_comp_descriptor *comp_desc) | |
| { | |
| struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | |
| struct usb_ep *ep; | |
| if (usb_endpoint_xfer_isoc(desc) && usb_endpoint_dir_in(desc)) { | |
| list_for_each_entry_reverse(ep, &ci->gadget.ep_list, ep_list) { | |
| if (ep->caps.dir_in && !ep->claimed) | |
| return ep; | |
| } | |
| } | |
| return NULL; | |
| } | |
| /* | |
| * Device operations part of the API to the USB controller hardware, | |
| * which don't involve endpoints (or i/o) | |
| * Check "usb_gadget.h" for details | |
| */ | |
| static const struct usb_gadget_ops usb_gadget_ops = { | |
| .get_frame = ci_udc_get_frame, | |
| .vbus_session = ci_udc_vbus_session, | |
| .wakeup = ci_udc_wakeup, | |
| .set_selfpowered = ci_udc_selfpowered, | |
| .pullup = ci_udc_pullup, | |
| .vbus_draw = ci_udc_vbus_draw, | |
| .udc_start = ci_udc_start, | |
| .udc_stop = ci_udc_stop, | |
| .match_ep = ci_udc_match_ep, | |
| }; | |
| static int init_eps(struct ci_hdrc *ci) | |
| { | |
| int retval = 0, i, j; | |
| memset(ci->ci_hw_ep, 0, sizeof(ci->ci_hw_ep)); | |
| for (i = 0; i < ci->hw_ep_max/2; i++) | |
| for (j = RX; j <= TX; j++) { | |
| int k = i + j * ci->hw_ep_max/2; | |
| struct ci_hw_ep *hwep = &ci->ci_hw_ep[k]; | |
| scnprintf(hwep->name, sizeof(hwep->name), "ep%i%s", i, | |
| (j == TX) ? "in" : "out"); | |
| hwep->ci = ci; | |
| hwep->lock = &ci->lock; | |
| hwep->td_pool = ci->td_pool; | |
| hwep->ep.name = hwep->name; | |
| hwep->ep.ops = &usb_ep_ops; | |
| if (i == 0) { | |
| hwep->ep.caps.type_control = true; | |
| } else { | |
| hwep->ep.caps.type_iso = true; | |
| hwep->ep.caps.type_bulk = true; | |
| hwep->ep.caps.type_int = true; | |
| } | |
| if (j == TX) | |
| hwep->ep.caps.dir_in = true; | |
| else | |
| hwep->ep.caps.dir_out = true; | |
| /* | |
| * for ep0: maxP defined in desc, for other | |
| * eps, maxP is set by epautoconfig() called | |
| * by gadget layer | |
| */ | |
| usb_ep_set_maxpacket_limit(&hwep->ep, (unsigned short)~0); | |
| INIT_LIST_HEAD(&hwep->qh.queue); | |
| hwep->qh.ptr = dma_pool_zalloc(ci->qh_pool, GFP_KERNEL, | |
| &hwep->qh.dma); | |
| if (hwep->qh.ptr == NULL) | |
| retval = -ENOMEM; | |
| /* | |
| * set up shorthands for ep0 out and in endpoints, | |
| * don't add to gadget's ep_list | |
| */ | |
| if (i == 0) { | |
| if (j == RX) | |
| ci->ep0out = hwep; | |
| else | |
| ci->ep0in = hwep; | |
| usb_ep_set_maxpacket_limit(&hwep->ep, CTRL_PAYLOAD_MAX); | |
| continue; | |
| } | |
| list_add_tail(&hwep->ep.ep_list, &ci->gadget.ep_list); | |
| } | |
| return retval; | |
| } | |
| static void destroy_eps(struct ci_hdrc *ci) | |
| { | |
| int i; | |
| for (i = 0; i < ci->hw_ep_max; i++) { | |
| struct ci_hw_ep *hwep = &ci->ci_hw_ep[i]; | |
| if (hwep->pending_td) | |
| free_pending_td(hwep); | |
| dma_pool_free(ci->qh_pool, hwep->qh.ptr, hwep->qh.dma); | |
| } | |
| } | |
| /** | |
| * ci_udc_start: register a gadget driver | |
| * @gadget: our gadget | |
| * @driver: the driver being registered | |
| * | |
| * Interrupts are enabled here. | |
| */ | |
| static int ci_udc_start(struct usb_gadget *gadget, | |
| struct usb_gadget_driver *driver) | |
| { | |
| struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | |
| int retval; | |
| if (driver->disconnect == NULL) | |
| return -EINVAL; | |
| ci->ep0out->ep.desc = &ctrl_endpt_out_desc; | |
| retval = usb_ep_enable(&ci->ep0out->ep); | |
| if (retval) | |
| return retval; | |
| ci->ep0in->ep.desc = &ctrl_endpt_in_desc; | |
| retval = usb_ep_enable(&ci->ep0in->ep); | |
| if (retval) | |
| return retval; | |
| ci->driver = driver; | |
| /* Start otg fsm for B-device */ | |
| if (ci_otg_is_fsm_mode(ci) && ci->fsm.id) { | |
| ci_hdrc_otg_fsm_start(ci); | |
| return retval; | |
| } | |
| if (ci->vbus_active) | |
| ci_hdrc_gadget_connect(gadget, 1); | |
| else | |
| usb_udc_vbus_handler(&ci->gadget, false); | |
| return retval; | |
| } | |
| static void ci_udc_stop_for_otg_fsm(struct ci_hdrc *ci) | |
| { | |
| if (!ci_otg_is_fsm_mode(ci)) | |
| return; | |
| mutex_lock(&ci->fsm.lock); | |
| if (ci->fsm.otg->state == OTG_STATE_A_PERIPHERAL) { | |
| ci->fsm.a_bidl_adis_tmout = 1; | |
| ci_hdrc_otg_fsm_start(ci); | |
| } else if (ci->fsm.otg->state == OTG_STATE_B_PERIPHERAL) { | |
| ci->fsm.protocol = PROTO_UNDEF; | |
| ci->fsm.otg->state = OTG_STATE_UNDEFINED; | |
| } | |
| mutex_unlock(&ci->fsm.lock); | |
| } | |
| /* | |
| * ci_udc_stop: unregister a gadget driver | |
| */ | |
| static int ci_udc_stop(struct usb_gadget *gadget) | |
| { | |
| struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | |
| unsigned long flags; | |
| spin_lock_irqsave(&ci->lock, flags); | |
| ci->driver = NULL; | |
| if (ci->vbus_active) { | |
| hw_device_state(ci, 0); | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| if (ci->platdata->notify_event) | |
| ci->platdata->notify_event(ci, | |
| CI_HDRC_CONTROLLER_STOPPED_EVENT); | |
| _gadget_stop_activity(&ci->gadget); | |
| spin_lock_irqsave(&ci->lock, flags); | |
| pm_runtime_put(ci->dev); | |
| } | |
| spin_unlock_irqrestore(&ci->lock, flags); | |
| ci_udc_stop_for_otg_fsm(ci); | |
| return 0; | |
| } | |
| /****************************************************************************** | |
| * BUS block | |
| *****************************************************************************/ | |
| /* | |
| * udc_irq: ci interrupt handler | |
| * | |
| * This function returns IRQ_HANDLED if the IRQ has been handled | |
| * It locks access to registers | |
| */ | |
| static irqreturn_t udc_irq(struct ci_hdrc *ci) | |
| { | |
| irqreturn_t retval; | |
| u32 intr; | |
| if (ci == NULL) | |
| return IRQ_HANDLED; | |
| spin_lock(&ci->lock); | |
| if (ci->platdata->flags & CI_HDRC_REGS_SHARED) { | |
| if (hw_read(ci, OP_USBMODE, USBMODE_CM) != | |
| USBMODE_CM_DC) { | |
| spin_unlock(&ci->lock); | |
| return IRQ_NONE; | |
| } | |
| } | |
| intr = hw_test_and_clear_intr_active(ci); | |
| if (intr) { | |
| /* order defines priority - do NOT change it */ | |
| if (USBi_URI & intr) | |
| isr_reset_handler(ci); | |
| if (USBi_PCI & intr) { | |
| ci->gadget.speed = hw_port_is_high_speed(ci) ? | |
| USB_SPEED_HIGH : USB_SPEED_FULL; | |
| if (ci->usb_phy) | |
| usb_phy_set_event(ci->usb_phy, | |
| USB_EVENT_ENUMERATED); | |
| if (ci->suspended) { | |
| if (ci->driver->resume) { | |
| spin_unlock(&ci->lock); | |
| ci->driver->resume(&ci->gadget); | |
| spin_lock(&ci->lock); | |
| } | |
| ci->suspended = 0; | |
| usb_gadget_set_state(&ci->gadget, | |
| ci->resume_state); | |
| } | |
| } | |
| if ((USBi_UI | USBi_UEI) & intr) | |
| isr_tr_complete_handler(ci); | |
| if ((USBi_SLI & intr) && !(ci->suspended)) { | |
| ci->suspended = 1; | |
| ci->resume_state = ci->gadget.state; | |
| if (ci->gadget.speed != USB_SPEED_UNKNOWN && | |
| ci->driver->suspend) { | |
| spin_unlock(&ci->lock); | |
| ci->driver->suspend(&ci->gadget); | |
| spin_lock(&ci->lock); | |
| } | |
| usb_gadget_set_state(&ci->gadget, | |
| USB_STATE_SUSPENDED); | |
| } | |
| retval = IRQ_HANDLED; | |
| } else { | |
| retval = IRQ_NONE; | |
| } | |
| spin_unlock(&ci->lock); | |
| return retval; | |
| } | |
| /** | |
| * udc_start: initialize gadget role | |
| * @ci: chipidea controller | |
| */ | |
| static int udc_start(struct ci_hdrc *ci) | |
| { | |
| struct device *dev = ci->dev; | |
| struct usb_otg_caps *otg_caps = &ci->platdata->ci_otg_caps; | |
| int retval = 0; | |
| memset(&ci->gadget, 0, sizeof(ci->gadget)); | |
| ci->gadget.ops = &usb_gadget_ops; | |
| ci->gadget.speed = USB_SPEED_UNKNOWN; | |
| ci->gadget.max_speed = USB_SPEED_HIGH; | |
| ci->gadget.name = ci->platdata->name; | |
| ci->gadget.otg_caps = otg_caps; | |
| ci->gadget.sg_supported = 1; | |
| ci->gadget.irq = ci->irq; | |
| if (ci->platdata->flags & CI_HDRC_REQUIRES_ALIGNED_DMA) | |
| ci->gadget.quirk_avoids_skb_reserve = 1; | |
| if (ci->is_otg && (otg_caps->hnp_support || otg_caps->srp_support || | |
| otg_caps->adp_support)) | |
| ci->gadget.is_otg = 1; | |
| INIT_LIST_HEAD(&ci->gadget.ep_list); | |
| /* alloc resources */ | |
| ci->qh_pool = dma_pool_create("ci_hw_qh", dev->parent, | |
| sizeof(struct ci_hw_qh), | |
| 64, CI_HDRC_PAGE_SIZE); | |
| if (ci->qh_pool == NULL) | |
| return -ENOMEM; | |
| ci->td_pool = dma_pool_create("ci_hw_td", dev->parent, | |
| sizeof(struct ci_hw_td), | |
| 64, CI_HDRC_PAGE_SIZE); | |
| if (ci->td_pool == NULL) { | |
| retval = -ENOMEM; | |
| goto free_qh_pool; | |
| } | |
| retval = init_eps(ci); | |
| if (retval) | |
| goto free_pools; | |
| ci->gadget.ep0 = &ci->ep0in->ep; | |
| if (ci->platdata->pins_device) | |
| pinctrl_select_state(ci->platdata->pctl, | |
| ci->platdata->pins_device); | |
| retval = usb_add_gadget_udc(dev, &ci->gadget); | |
| if (retval) | |
| goto destroy_eps; | |
| ci_udc_enable_vbus_irq(ci, true); | |
| return retval; | |
| destroy_eps: | |
| destroy_eps(ci); | |
| free_pools: | |
| dma_pool_destroy(ci->td_pool); | |
| free_qh_pool: | |
| dma_pool_destroy(ci->qh_pool); | |
| return retval; | |
| } | |
| /** | |
| * udc_stop: deinitialize gadget role | |
| * @ci: chipidea controller | |
| */ | |
| static void udc_stop(struct ci_hdrc *ci) | |
| { | |
| ci_udc_enable_vbus_irq(ci, false); | |
| usb_del_gadget_udc(&ci->gadget); | |
| ci->vbus_active = 0; | |
| destroy_eps(ci); | |
| dma_pool_destroy(ci->td_pool); | |
| dma_pool_destroy(ci->qh_pool); | |
| if (ci->platdata->pins_device && ci->platdata->pins_default) | |
| pinctrl_select_state(ci->platdata->pctl, | |
| ci->platdata->pins_default); | |
| } | |
| #ifdef CONFIG_PM_SLEEP | |
| static void udc_suspend(struct ci_hdrc *ci) | |
| { | |
| /* | |
| * Set OP_ENDPTLISTADDR to be non-zero for | |
| * checking if controller resume from power lost | |
| * in non-host mode. | |
| */ | |
| if (hw_read(ci, OP_ENDPTLISTADDR, ~0) == 0) | |
| hw_write(ci, OP_ENDPTLISTADDR, ~0, ~0); | |
| if (ci->gadget.connected && | |
| (!ci->suspended || !device_may_wakeup(ci->dev))) | |
| usb_gadget_disconnect(&ci->gadget); | |
| } | |
| static void udc_resume(struct ci_hdrc *ci, bool power_lost) | |
| { | |
| if (power_lost) { | |
| ci_udc_enable_vbus_irq(ci, true); | |
| if (ci->vbus_active) | |
| usb_gadget_vbus_disconnect(&ci->gadget); | |
| } else if (ci->vbus_active && ci->driver && | |
| !ci->gadget.connected) { | |
| usb_gadget_connect(&ci->gadget); | |
| } | |
| /* Restore value 0 if it was set for power lost check */ | |
| if (hw_read(ci, OP_ENDPTLISTADDR, ~0) == 0xFFFFFFFF) | |
| hw_write(ci, OP_ENDPTLISTADDR, ~0, 0); | |
| } | |
| #endif | |
| /** | |
| * ci_hdrc_gadget_init - initialize device related bits | |
| * @ci: the controller | |
| * | |
| * This function initializes the gadget, if the device is "device capable". | |
| */ | |
| int ci_hdrc_gadget_init(struct ci_hdrc *ci) | |
| { | |
| struct ci_role_driver *rdrv; | |
| if (!hw_read(ci, CAP_DCCPARAMS, DCCPARAMS_DC)) | |
| return -ENXIO; | |
| rdrv = devm_kzalloc(ci->dev, sizeof(*rdrv), GFP_KERNEL); | |
| if (!rdrv) | |
| return -ENOMEM; | |
| rdrv->start = udc_start; | |
| rdrv->stop = udc_stop; | |
| #ifdef CONFIG_PM_SLEEP | |
| rdrv->suspend = udc_suspend; | |
| rdrv->resume = udc_resume; | |
| #endif | |
| rdrv->irq = udc_irq; | |
| rdrv->name = "gadget"; | |
| ci->roles[CI_ROLE_GADGET] = rdrv; | |
| /* Pull down DP for possible charger detection */ | |
| hw_write(ci, OP_USBCMD, USBCMD_RS, 0); | |
| return 0; | |
| } | |
| /* | |
| * ci_hdrc_gadget_destroy: parent remove must call this to remove UDC | |
| * | |
| * No interrupts active, the IRQ has been released | |
| */ | |
| void ci_hdrc_gadget_destroy(struct ci_hdrc *ci) | |
| { | |
| struct device *dev = &ci->gadget.dev; | |
| if (ci->roles[CI_ROLE_GADGET] && device_is_registered(dev)) | |
| udc_stop(ci); | |
| } |