| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Amlogic Thermal Sensor Driver | |
| * | |
| * Copyright (C) 2017 Huan Biao <huan.biao@amlogic.com> | |
| * Copyright (C) 2019 Guillaume La Roque <glaroque@baylibre.com> | |
| * | |
| * Register value to celsius temperature formulas: | |
| * Read_Val m * U | |
| * U = ---------, uptat = --------- | |
| * 2^16 1 + n * U | |
| * | |
| * Temperature = A * ( uptat + u_efuse / 2^16 )- B | |
| * | |
| * A B m n : calibration parameters | |
| * u_efuse : fused calibration value, it's a signed 16 bits value | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/clk.h> | |
| #include <linux/io.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regmap.h> | |
| #include <linux/thermal.h> | |
| #include <linux/firmware/meson/meson_sm.h> | |
| #include "thermal_hwmon.h" | |
| #define TSENSOR_CFG_REG1 0x4 | |
| #define TSENSOR_CFG_REG1_RSET_VBG BIT(12) | |
| #define TSENSOR_CFG_REG1_RSET_ADC BIT(11) | |
| #define TSENSOR_CFG_REG1_VCM_EN BIT(10) | |
| #define TSENSOR_CFG_REG1_VBG_EN BIT(9) | |
| #define TSENSOR_CFG_REG1_OUT_CTL BIT(6) | |
| #define TSENSOR_CFG_REG1_FILTER_EN BIT(5) | |
| #define TSENSOR_CFG_REG1_DEM_EN BIT(3) | |
| #define TSENSOR_CFG_REG1_CH_SEL GENMASK(1, 0) | |
| #define TSENSOR_CFG_REG1_ENABLE \ | |
| (TSENSOR_CFG_REG1_FILTER_EN | \ | |
| TSENSOR_CFG_REG1_VCM_EN | \ | |
| TSENSOR_CFG_REG1_VBG_EN | \ | |
| TSENSOR_CFG_REG1_DEM_EN | \ | |
| TSENSOR_CFG_REG1_CH_SEL) | |
| #define TSENSOR_STAT0 0x40 | |
| #define TSENSOR_STAT9 0x64 | |
| #define TSENSOR_READ_TEMP_MASK GENMASK(15, 0) | |
| #define TSENSOR_TEMP_MASK GENMASK(11, 0) | |
| #define TSENSOR_TRIM_SIGN_MASK BIT(15) | |
| #define TSENSOR_TRIM_TEMP_MASK GENMASK(14, 0) | |
| #define TSENSOR_TRIM_VERSION_MASK GENMASK(31, 24) | |
| #define TSENSOR_TRIM_VERSION(_version) \ | |
| FIELD_GET(TSENSOR_TRIM_VERSION_MASK, _version) | |
| #define TSENSOR_TRIM_CALIB_VALID_MASK (GENMASK(3, 2) | BIT(7)) | |
| #define TSENSOR_CALIB_OFFSET 1 | |
| #define TSENSOR_CALIB_SHIFT 4 | |
| /** | |
| * struct amlogic_thermal_soc_calib_data | |
| * @A: calibration parameters | |
| * @B: calibration parameters | |
| * @m: calibration parameters | |
| * @n: calibration parameters | |
| * | |
| * This structure is required for configuration of amlogic thermal driver. | |
| */ | |
| struct amlogic_thermal_soc_calib_data { | |
| int A; | |
| int B; | |
| int m; | |
| int n; | |
| }; | |
| /** | |
| * struct amlogic_thermal_data | |
| * @u_efuse_off: register offset to read fused calibration value | |
| * @calibration_parameters: calibration parameters structure pointer | |
| * @regmap_config: regmap config for the device | |
| * @use_sm: read data from secure monitor instead of efuse | |
| * This structure is required for configuration of amlogic thermal driver. | |
| */ | |
| struct amlogic_thermal_data { | |
| int u_efuse_off; | |
| const struct amlogic_thermal_soc_calib_data *calibration_parameters; | |
| const struct regmap_config *regmap_config; | |
| bool use_sm; | |
| }; | |
| struct amlogic_thermal { | |
| struct platform_device *pdev; | |
| const struct amlogic_thermal_data *data; | |
| struct regmap *regmap; | |
| struct regmap *sec_ao_map; | |
| struct clk *clk; | |
| struct thermal_zone_device *tzd; | |
| u32 trim_info; | |
| struct meson_sm_firmware *sm_fw; | |
| u32 tsensor_id; | |
| }; | |
| /* | |
| * Calculate a temperature value from a temperature code. | |
| * The unit of the temperature is degree milliCelsius. | |
| */ | |
| static int amlogic_thermal_code_to_millicelsius(struct amlogic_thermal *pdata, | |
| int temp_code) | |
| { | |
| const struct amlogic_thermal_soc_calib_data *param = | |
| pdata->data->calibration_parameters; | |
| int temp; | |
| s64 factor, uptat, uefuse; | |
| uefuse = pdata->trim_info & TSENSOR_TRIM_SIGN_MASK ? | |
| ~(pdata->trim_info & TSENSOR_TRIM_TEMP_MASK) + 1 : | |
| (pdata->trim_info & TSENSOR_TRIM_TEMP_MASK); | |
| factor = param->n * temp_code; | |
| factor = div_s64(factor, 100); | |
| uptat = temp_code * param->m; | |
| uptat = div_s64(uptat, 100); | |
| uptat = uptat * BIT(16); | |
| uptat = div_s64(uptat, BIT(16) + factor); | |
| temp = (uptat + uefuse) * param->A; | |
| temp = div_s64(temp, BIT(16)); | |
| temp = (temp - param->B) * 100; | |
| return temp; | |
| } | |
| static int amlogic_thermal_enable(struct amlogic_thermal *data) | |
| { | |
| int ret; | |
| ret = clk_prepare_enable(data->clk); | |
| if (ret) | |
| return ret; | |
| regmap_update_bits(data->regmap, TSENSOR_CFG_REG1, | |
| TSENSOR_CFG_REG1_ENABLE, TSENSOR_CFG_REG1_ENABLE); | |
| return 0; | |
| } | |
| static void amlogic_thermal_disable(struct amlogic_thermal *data) | |
| { | |
| regmap_update_bits(data->regmap, TSENSOR_CFG_REG1, | |
| TSENSOR_CFG_REG1_ENABLE, 0); | |
| clk_disable_unprepare(data->clk); | |
| } | |
| static int amlogic_thermal_get_temp(struct thermal_zone_device *tz, int *temp) | |
| { | |
| unsigned int tval; | |
| struct amlogic_thermal *pdata = thermal_zone_device_priv(tz); | |
| if (!pdata) | |
| return -EINVAL; | |
| regmap_read(pdata->regmap, TSENSOR_STAT0, &tval); | |
| *temp = | |
| amlogic_thermal_code_to_millicelsius(pdata, | |
| tval & TSENSOR_READ_TEMP_MASK); | |
| return 0; | |
| } | |
| static int amlogic_thermal_probe_sm(struct platform_device *pdev, | |
| struct amlogic_thermal *pdata) | |
| { | |
| struct device *dev = &pdev->dev; | |
| struct of_phandle_args ph_args; | |
| int ret; | |
| ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node, | |
| "amlogic,secure-monitor", | |
| 1, 0, &ph_args); | |
| if (ret) | |
| return ret; | |
| if (!ph_args.np) { | |
| dev_err(dev, "Failed to parse secure monitor phandle\n"); | |
| return -ENODEV; | |
| } | |
| pdata->sm_fw = meson_sm_get(ph_args.np); | |
| of_node_put(ph_args.np); | |
| if (!pdata->sm_fw) { | |
| dev_err(dev, "Failed to get secure monitor firmware\n"); | |
| return -EPROBE_DEFER; | |
| } | |
| pdata->tsensor_id = ph_args.args[0]; | |
| return meson_sm_get_thermal_calib(pdata->sm_fw, | |
| &pdata->trim_info, | |
| pdata->tsensor_id); | |
| } | |
| static int amlogic_thermal_probe_syscon(struct platform_device *pdev, | |
| struct amlogic_thermal *pdata) | |
| { | |
| struct device *dev = &pdev->dev; | |
| int ver; | |
| pdata->sec_ao_map = | |
| syscon_regmap_lookup_by_phandle(pdev->dev.of_node, | |
| "amlogic,ao-secure"); | |
| if (IS_ERR(pdata->sec_ao_map)) { | |
| dev_err(dev, "syscon regmap lookup failed.\n"); | |
| return PTR_ERR(pdata->sec_ao_map); | |
| } | |
| regmap_read(pdata->sec_ao_map, pdata->data->u_efuse_off, | |
| &pdata->trim_info); | |
| ver = TSENSOR_TRIM_VERSION(pdata->trim_info); | |
| if ((ver & TSENSOR_TRIM_CALIB_VALID_MASK) == 0) { | |
| dev_err(&pdata->pdev->dev, | |
| "tsensor thermal calibration not supported: 0x%x!\n", | |
| ver); | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static const struct thermal_zone_device_ops amlogic_thermal_ops = { | |
| .get_temp = amlogic_thermal_get_temp, | |
| }; | |
| static const struct regmap_config amlogic_thermal_regmap_config_g12a = { | |
| .reg_bits = 8, | |
| .val_bits = 32, | |
| .reg_stride = 4, | |
| .max_register = TSENSOR_STAT9, | |
| }; | |
| static const struct amlogic_thermal_soc_calib_data amlogic_thermal_g12a = { | |
| .A = 9411, | |
| .B = 3159, | |
| .m = 424, | |
| .n = 324, | |
| }; | |
| static const struct amlogic_thermal_data amlogic_thermal_g12a_cpu_param = { | |
| .u_efuse_off = 0x128, | |
| .calibration_parameters = &amlogic_thermal_g12a, | |
| .regmap_config = &amlogic_thermal_regmap_config_g12a, | |
| }; | |
| static const struct amlogic_thermal_data amlogic_thermal_g12a_ddr_param = { | |
| .u_efuse_off = 0xf0, | |
| .calibration_parameters = &amlogic_thermal_g12a, | |
| .regmap_config = &amlogic_thermal_regmap_config_g12a, | |
| }; | |
| static const struct amlogic_thermal_data amlogic_thermal_a1_cpu_param = { | |
| .u_efuse_off = 0x114, | |
| .calibration_parameters = &amlogic_thermal_g12a, | |
| .regmap_config = &amlogic_thermal_regmap_config_g12a, | |
| }; | |
| static const struct amlogic_thermal_data amlogic_thermal_t7_param = { | |
| .use_sm = true, | |
| .calibration_parameters = &amlogic_thermal_g12a, | |
| .regmap_config = &amlogic_thermal_regmap_config_g12a, | |
| }; | |
| static const struct of_device_id of_amlogic_thermal_match[] = { | |
| { | |
| .compatible = "amlogic,g12a-ddr-thermal", | |
| .data = &amlogic_thermal_g12a_ddr_param, | |
| }, | |
| { | |
| .compatible = "amlogic,g12a-cpu-thermal", | |
| .data = &amlogic_thermal_g12a_cpu_param, | |
| }, | |
| { | |
| .compatible = "amlogic,a1-cpu-thermal", | |
| .data = &amlogic_thermal_a1_cpu_param, | |
| }, | |
| { | |
| .compatible = "amlogic,t7-thermal", | |
| .data = &amlogic_thermal_t7_param, | |
| }, | |
| { /* sentinel */ } | |
| }; | |
| MODULE_DEVICE_TABLE(of, of_amlogic_thermal_match); | |
| static int amlogic_thermal_probe(struct platform_device *pdev) | |
| { | |
| struct amlogic_thermal *pdata; | |
| struct device *dev = &pdev->dev; | |
| void __iomem *base; | |
| int ret; | |
| pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); | |
| if (!pdata) | |
| return -ENOMEM; | |
| pdata->data = of_device_get_match_data(dev); | |
| pdata->pdev = pdev; | |
| platform_set_drvdata(pdev, pdata); | |
| base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(base)) | |
| return PTR_ERR(base); | |
| pdata->regmap = devm_regmap_init_mmio(dev, base, | |
| pdata->data->regmap_config); | |
| if (IS_ERR(pdata->regmap)) | |
| return PTR_ERR(pdata->regmap); | |
| pdata->clk = devm_clk_get(dev, NULL); | |
| if (IS_ERR(pdata->clk)) | |
| return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get clock\n"); | |
| if (pdata->data->use_sm) | |
| ret = amlogic_thermal_probe_sm(pdev, pdata); | |
| else | |
| ret = amlogic_thermal_probe_syscon(pdev, pdata); | |
| if (ret) | |
| return ret; | |
| pdata->tzd = devm_thermal_of_zone_register(&pdev->dev, | |
| 0, | |
| pdata, | |
| &amlogic_thermal_ops); | |
| if (IS_ERR(pdata->tzd)) { | |
| ret = PTR_ERR(pdata->tzd); | |
| dev_err(dev, "Failed to register tsensor: %d\n", ret); | |
| return ret; | |
| } | |
| devm_thermal_add_hwmon_sysfs(&pdev->dev, pdata->tzd); | |
| ret = amlogic_thermal_enable(pdata); | |
| return ret; | |
| } | |
| static void amlogic_thermal_remove(struct platform_device *pdev) | |
| { | |
| struct amlogic_thermal *data = platform_get_drvdata(pdev); | |
| amlogic_thermal_disable(data); | |
| } | |
| static int amlogic_thermal_suspend(struct device *dev) | |
| { | |
| struct amlogic_thermal *data = dev_get_drvdata(dev); | |
| amlogic_thermal_disable(data); | |
| return 0; | |
| } | |
| static int amlogic_thermal_resume(struct device *dev) | |
| { | |
| struct amlogic_thermal *data = dev_get_drvdata(dev); | |
| return amlogic_thermal_enable(data); | |
| } | |
| static DEFINE_SIMPLE_DEV_PM_OPS(amlogic_thermal_pm_ops, | |
| amlogic_thermal_suspend, | |
| amlogic_thermal_resume); | |
| static struct platform_driver amlogic_thermal_driver = { | |
| .driver = { | |
| .name = "amlogic_thermal", | |
| .pm = pm_ptr(&amlogic_thermal_pm_ops), | |
| .of_match_table = of_amlogic_thermal_match, | |
| }, | |
| .probe = amlogic_thermal_probe, | |
| .remove = amlogic_thermal_remove, | |
| }; | |
| module_platform_driver(amlogic_thermal_driver); | |
| MODULE_AUTHOR("Guillaume La Roque <glaroque@baylibre.com>"); | |
| MODULE_DESCRIPTION("Amlogic thermal driver"); | |
| MODULE_LICENSE("GPL v2"); |