| // SPDX-License-Identifier: GPL-2.0+ | |
| // | |
| // wm8994-regulator.c -- Regulator driver for the WM8994 | |
| // | |
| // Copyright 2009 Wolfson Microelectronics PLC. | |
| // | |
| // Author: Mark Brown <broonie@opensource.wolfsonmicro.com> | |
| #include <linux/module.h> | |
| #include <linux/moduleparam.h> | |
| #include <linux/init.h> | |
| #include <linux/bitops.h> | |
| #include <linux/err.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regulator/driver.h> | |
| #include <linux/regulator/machine.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/slab.h> | |
| #include <linux/mfd/wm8994/core.h> | |
| #include <linux/mfd/wm8994/registers.h> | |
| #include <linux/mfd/wm8994/pdata.h> | |
| struct wm8994_ldo { | |
| struct regulator_dev *regulator; | |
| struct wm8994 *wm8994; | |
| struct regulator_consumer_supply supply; | |
| struct regulator_init_data init_data; | |
| }; | |
| #define WM8994_LDO1_MAX_SELECTOR 0x7 | |
| #define WM8994_LDO2_MAX_SELECTOR 0x3 | |
| static const struct regulator_ops wm8994_ldo1_ops = { | |
| .list_voltage = regulator_list_voltage_linear, | |
| .map_voltage = regulator_map_voltage_linear, | |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, | |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, | |
| }; | |
| static int wm8994_ldo2_list_voltage(struct regulator_dev *rdev, | |
| unsigned int selector) | |
| { | |
| struct wm8994_ldo *ldo = rdev_get_drvdata(rdev); | |
| if (selector > WM8994_LDO2_MAX_SELECTOR) | |
| return -EINVAL; | |
| switch (ldo->wm8994->type) { | |
| case WM8994: | |
| return (selector * 100000) + 900000; | |
| case WM8958: | |
| return (selector * 100000) + 1000000; | |
| case WM1811: | |
| switch (selector) { | |
| case 0: | |
| return -EINVAL; | |
| default: | |
| return (selector * 100000) + 950000; | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static const struct regulator_ops wm8994_ldo2_ops = { | |
| .list_voltage = wm8994_ldo2_list_voltage, | |
| .get_voltage_sel = regulator_get_voltage_sel_regmap, | |
| .set_voltage_sel = regulator_set_voltage_sel_regmap, | |
| }; | |
| static const struct regulator_desc wm8994_ldo_desc[] = { | |
| { | |
| .name = "LDO1", | |
| .id = 1, | |
| .type = REGULATOR_VOLTAGE, | |
| .n_voltages = WM8994_LDO1_MAX_SELECTOR + 1, | |
| .vsel_reg = WM8994_LDO_1, | |
| .vsel_mask = WM8994_LDO1_VSEL_MASK, | |
| .ops = &wm8994_ldo1_ops, | |
| .min_uV = 2400000, | |
| .uV_step = 100000, | |
| .enable_time = 3000, | |
| .off_on_delay = 36000, | |
| .owner = THIS_MODULE, | |
| }, | |
| { | |
| .name = "LDO2", | |
| .id = 2, | |
| .type = REGULATOR_VOLTAGE, | |
| .n_voltages = WM8994_LDO2_MAX_SELECTOR + 1, | |
| .vsel_reg = WM8994_LDO_2, | |
| .vsel_mask = WM8994_LDO2_VSEL_MASK, | |
| .ops = &wm8994_ldo2_ops, | |
| .enable_time = 3000, | |
| .off_on_delay = 36000, | |
| .owner = THIS_MODULE, | |
| }, | |
| }; | |
| static const struct regulator_desc wm8958_ldo_desc[] = { | |
| { | |
| .name = "LDO1", | |
| .id = 1, | |
| .type = REGULATOR_VOLTAGE, | |
| .n_voltages = WM8994_LDO1_MAX_SELECTOR + 1, | |
| .vsel_reg = WM8994_LDO_1, | |
| .vsel_mask = WM8994_LDO1_VSEL_MASK, | |
| .ops = &wm8994_ldo1_ops, | |
| .min_uV = 2400000, | |
| .uV_step = 100000, | |
| .enable_time = 3000, | |
| .owner = THIS_MODULE, | |
| }, | |
| { | |
| .name = "LDO2", | |
| .id = 2, | |
| .type = REGULATOR_VOLTAGE, | |
| .n_voltages = WM8994_LDO2_MAX_SELECTOR + 1, | |
| .vsel_reg = WM8994_LDO_2, | |
| .vsel_mask = WM8994_LDO2_VSEL_MASK, | |
| .ops = &wm8994_ldo2_ops, | |
| .enable_time = 3000, | |
| .owner = THIS_MODULE, | |
| }, | |
| }; | |
| static const struct regulator_consumer_supply wm8994_ldo_consumer[] = { | |
| { .supply = "AVDD1" }, | |
| { .supply = "DCVDD" }, | |
| }; | |
| static const struct regulator_init_data wm8994_ldo_default[] = { | |
| { | |
| .constraints = { | |
| .valid_ops_mask = REGULATOR_CHANGE_STATUS, | |
| }, | |
| .num_consumer_supplies = 1, | |
| }, | |
| { | |
| .constraints = { | |
| .valid_ops_mask = REGULATOR_CHANGE_STATUS, | |
| }, | |
| .num_consumer_supplies = 1, | |
| }, | |
| }; | |
| static int wm8994_ldo_probe(struct platform_device *pdev) | |
| { | |
| struct wm8994 *wm8994 = dev_get_drvdata(pdev->dev.parent); | |
| struct wm8994_pdata *pdata = dev_get_platdata(wm8994->dev); | |
| int id = pdev->id % ARRAY_SIZE(pdata->ldo); | |
| struct regulator_config config = { }; | |
| struct wm8994_ldo *ldo; | |
| struct gpio_desc *gpiod; | |
| int ret; | |
| dev_dbg(&pdev->dev, "Probing LDO%d\n", id + 1); | |
| ldo = devm_kzalloc(&pdev->dev, sizeof(struct wm8994_ldo), GFP_KERNEL); | |
| if (!ldo) | |
| return -ENOMEM; | |
| ldo->wm8994 = wm8994; | |
| ldo->supply = wm8994_ldo_consumer[id]; | |
| ldo->supply.dev_name = dev_name(wm8994->dev); | |
| config.dev = wm8994->dev; | |
| config.driver_data = ldo; | |
| config.regmap = wm8994->regmap; | |
| config.init_data = &ldo->init_data; | |
| /* | |
| * Look up LDO enable GPIO from the parent device node, we don't | |
| * use devm because the regulator core will free the GPIO | |
| */ | |
| gpiod = gpiod_get_optional(pdev->dev.parent, | |
| id ? "wlf,ldo2ena" : "wlf,ldo1ena", | |
| GPIOD_OUT_LOW | | |
| GPIOD_FLAGS_BIT_NONEXCLUSIVE); | |
| if (IS_ERR(gpiod)) | |
| return PTR_ERR(gpiod); | |
| config.ena_gpiod = gpiod; | |
| /* Use default constraints if none set up */ | |
| if (!pdata || !pdata->ldo[id].init_data || wm8994->dev->of_node) { | |
| dev_dbg(wm8994->dev, "Using default init data, supply %s %s\n", | |
| ldo->supply.dev_name, ldo->supply.supply); | |
| ldo->init_data = wm8994_ldo_default[id]; | |
| ldo->init_data.consumer_supplies = &ldo->supply; | |
| if (!gpiod) | |
| ldo->init_data.constraints.valid_ops_mask = 0; | |
| } else { | |
| ldo->init_data = *pdata->ldo[id].init_data; | |
| } | |
| /* | |
| * At this point the GPIO descriptor is handled over to the | |
| * regulator core and we need not worry about it on the | |
| * error path. | |
| */ | |
| if (ldo->wm8994->type == WM8994) { | |
| ldo->regulator = devm_regulator_register(&pdev->dev, | |
| &wm8994_ldo_desc[id], | |
| &config); | |
| } else { | |
| ldo->regulator = devm_regulator_register(&pdev->dev, | |
| &wm8958_ldo_desc[id], | |
| &config); | |
| } | |
| if (IS_ERR(ldo->regulator)) { | |
| ret = PTR_ERR(ldo->regulator); | |
| dev_err(wm8994->dev, "Failed to register LDO%d: %d\n", | |
| id + 1, ret); | |
| return ret; | |
| } | |
| platform_set_drvdata(pdev, ldo); | |
| return 0; | |
| } | |
| static struct platform_driver wm8994_ldo_driver = { | |
| .probe = wm8994_ldo_probe, | |
| .driver = { | |
| .name = "wm8994-ldo", | |
| .probe_type = PROBE_FORCE_SYNCHRONOUS, | |
| }, | |
| }; | |
| module_platform_driver(wm8994_ldo_driver); | |
| /* Module information */ | |
| MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>"); | |
| MODULE_DESCRIPTION("WM8994 LDO driver"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_ALIAS("platform:wm8994-ldo"); |