| // SPDX-License-Identifier: GPL-2.0-only | |
| /* MCP23S08 SPI/I2C GPIO driver */ | |
| #include <linux/bitops.h> | |
| #include <linux/kernel.h> | |
| #include <linux/device.h> | |
| #include <linux/mutex.h> | |
| #include <linux/module.h> | |
| #include <linux/export.h> | |
| #include <linux/gpio/driver.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/seq_file.h> | |
| #include <linux/slab.h> | |
| #include <asm/byteorder.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/regmap.h> | |
| #include <linux/pinctrl/pinctrl.h> | |
| #include <linux/pinctrl/pinconf.h> | |
| #include <linux/pinctrl/pinconf-generic.h> | |
| #include "pinctrl-mcp23s08.h" | |
| /* Registers are all 8 bits wide. | |
| * | |
| * The mcp23s17 has twice as many bits, and can be configured to work | |
| * with either 16 bit registers or with two adjacent 8 bit banks. | |
| */ | |
| #define MCP_IODIR 0x00 /* init/reset: all ones */ | |
| #define MCP_IPOL 0x01 | |
| #define MCP_GPINTEN 0x02 | |
| #define MCP_DEFVAL 0x03 | |
| #define MCP_INTCON 0x04 | |
| #define MCP_IOCON 0x05 | |
| # define IOCON_MIRROR (1 << 6) | |
| # define IOCON_SEQOP (1 << 5) | |
| # define IOCON_HAEN (1 << 3) | |
| # define IOCON_ODR (1 << 2) | |
| # define IOCON_INTPOL (1 << 1) | |
| # define IOCON_INTCC (1) | |
| #define MCP_GPPU 0x06 | |
| #define MCP_INTF 0x07 | |
| #define MCP_INTCAP 0x08 | |
| #define MCP_GPIO 0x09 | |
| #define MCP_OLAT 0x0a | |
| static const struct regmap_range mcp23x08_volatile_range = { | |
| .range_min = MCP_INTF, | |
| .range_max = MCP_GPIO, | |
| }; | |
| static const struct regmap_access_table mcp23x08_volatile_table = { | |
| .yes_ranges = &mcp23x08_volatile_range, | |
| .n_yes_ranges = 1, | |
| }; | |
| static const struct regmap_range mcp23x08_precious_range = { | |
| .range_min = MCP_GPIO, | |
| .range_max = MCP_GPIO, | |
| }; | |
| static const struct regmap_access_table mcp23x08_precious_table = { | |
| .yes_ranges = &mcp23x08_precious_range, | |
| .n_yes_ranges = 1, | |
| }; | |
| const struct regmap_config mcp23x08_regmap = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .reg_stride = 1, | |
| .volatile_table = &mcp23x08_volatile_table, | |
| .precious_table = &mcp23x08_precious_table, | |
| .num_reg_defaults_raw = MCP_OLAT + 1, | |
| .cache_type = REGCACHE_MAPLE, | |
| .max_register = MCP_OLAT, | |
| .disable_locking = true, /* mcp->lock protects the regmap */ | |
| }; | |
| EXPORT_SYMBOL_GPL(mcp23x08_regmap); | |
| static const struct regmap_range mcp23x17_volatile_range = { | |
| .range_min = MCP_INTF << 1, | |
| .range_max = MCP_GPIO << 1, | |
| }; | |
| static const struct regmap_access_table mcp23x17_volatile_table = { | |
| .yes_ranges = &mcp23x17_volatile_range, | |
| .n_yes_ranges = 1, | |
| }; | |
| static const struct regmap_range mcp23x17_precious_range = { | |
| .range_min = MCP_INTCAP << 1, | |
| .range_max = MCP_GPIO << 1, | |
| }; | |
| static const struct regmap_access_table mcp23x17_precious_table = { | |
| .yes_ranges = &mcp23x17_precious_range, | |
| .n_yes_ranges = 1, | |
| }; | |
| const struct regmap_config mcp23x17_regmap = { | |
| .reg_bits = 8, | |
| .val_bits = 16, | |
| .reg_stride = 2, | |
| .max_register = MCP_OLAT << 1, | |
| .volatile_table = &mcp23x17_volatile_table, | |
| .precious_table = &mcp23x17_precious_table, | |
| .num_reg_defaults_raw = MCP_OLAT + 1, | |
| .cache_type = REGCACHE_MAPLE, | |
| .val_format_endian = REGMAP_ENDIAN_LITTLE, | |
| .disable_locking = true, /* mcp->lock protects the regmap */ | |
| }; | |
| EXPORT_SYMBOL_GPL(mcp23x17_regmap); | |
| static int mcp_read(struct mcp23s08 *mcp, unsigned int reg, unsigned int *val) | |
| { | |
| return regmap_read(mcp->regmap, reg << mcp->reg_shift, val); | |
| } | |
| static int mcp_write(struct mcp23s08 *mcp, unsigned int reg, unsigned int val) | |
| { | |
| return regmap_write(mcp->regmap, reg << mcp->reg_shift, val); | |
| } | |
| static int mcp_update_bits(struct mcp23s08 *mcp, unsigned int reg, | |
| unsigned int mask, unsigned int val) | |
| { | |
| return regmap_update_bits(mcp->regmap, reg << mcp->reg_shift, | |
| mask, val); | |
| } | |
| static int mcp_set_bit(struct mcp23s08 *mcp, unsigned int reg, | |
| unsigned int pin, bool enabled) | |
| { | |
| u16 mask = BIT(pin); | |
| return mcp_update_bits(mcp, reg, mask, enabled ? mask : 0); | |
| } | |
| static const struct pinctrl_pin_desc mcp23x08_pins[] = { | |
| PINCTRL_PIN(0, "gpio0"), | |
| PINCTRL_PIN(1, "gpio1"), | |
| PINCTRL_PIN(2, "gpio2"), | |
| PINCTRL_PIN(3, "gpio3"), | |
| PINCTRL_PIN(4, "gpio4"), | |
| PINCTRL_PIN(5, "gpio5"), | |
| PINCTRL_PIN(6, "gpio6"), | |
| PINCTRL_PIN(7, "gpio7"), | |
| }; | |
| static const struct pinctrl_pin_desc mcp23x17_pins[] = { | |
| PINCTRL_PIN(0, "gpio0"), | |
| PINCTRL_PIN(1, "gpio1"), | |
| PINCTRL_PIN(2, "gpio2"), | |
| PINCTRL_PIN(3, "gpio3"), | |
| PINCTRL_PIN(4, "gpio4"), | |
| PINCTRL_PIN(5, "gpio5"), | |
| PINCTRL_PIN(6, "gpio6"), | |
| PINCTRL_PIN(7, "gpio7"), | |
| PINCTRL_PIN(8, "gpio8"), | |
| PINCTRL_PIN(9, "gpio9"), | |
| PINCTRL_PIN(10, "gpio10"), | |
| PINCTRL_PIN(11, "gpio11"), | |
| PINCTRL_PIN(12, "gpio12"), | |
| PINCTRL_PIN(13, "gpio13"), | |
| PINCTRL_PIN(14, "gpio14"), | |
| PINCTRL_PIN(15, "gpio15"), | |
| }; | |
| static int mcp_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) | |
| { | |
| return 0; | |
| } | |
| static const char *mcp_pinctrl_get_group_name(struct pinctrl_dev *pctldev, | |
| unsigned int group) | |
| { | |
| return NULL; | |
| } | |
| static int mcp_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, | |
| unsigned int group, | |
| const unsigned int **pins, | |
| unsigned int *num_pins) | |
| { | |
| return -ENOTSUPP; | |
| } | |
| static const struct pinctrl_ops mcp_pinctrl_ops = { | |
| .get_groups_count = mcp_pinctrl_get_groups_count, | |
| .get_group_name = mcp_pinctrl_get_group_name, | |
| .get_group_pins = mcp_pinctrl_get_group_pins, | |
| #ifdef CONFIG_OF | |
| .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, | |
| .dt_free_map = pinconf_generic_dt_free_map, | |
| #endif | |
| }; | |
| static int mcp_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, | |
| unsigned long *config) | |
| { | |
| struct mcp23s08 *mcp = pinctrl_dev_get_drvdata(pctldev); | |
| enum pin_config_param param = pinconf_to_config_param(*config); | |
| unsigned int data, status; | |
| int ret; | |
| switch (param) { | |
| case PIN_CONFIG_BIAS_PULL_UP: | |
| mutex_lock(&mcp->lock); | |
| ret = mcp_read(mcp, MCP_GPPU, &data); | |
| mutex_unlock(&mcp->lock); | |
| if (ret < 0) | |
| return ret; | |
| status = (data & BIT(pin)) ? 1 : 0; | |
| break; | |
| default: | |
| return -ENOTSUPP; | |
| } | |
| *config = 0; | |
| return status ? 0 : -EINVAL; | |
| } | |
| static int mcp_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, | |
| unsigned long *configs, unsigned int num_configs) | |
| { | |
| struct mcp23s08 *mcp = pinctrl_dev_get_drvdata(pctldev); | |
| enum pin_config_param param; | |
| u32 arg; | |
| int ret = 0; | |
| int i; | |
| for (i = 0; i < num_configs; i++) { | |
| param = pinconf_to_config_param(configs[i]); | |
| arg = pinconf_to_config_argument(configs[i]); | |
| switch (param) { | |
| case PIN_CONFIG_BIAS_PULL_UP: | |
| mutex_lock(&mcp->lock); | |
| ret = mcp_set_bit(mcp, MCP_GPPU, pin, arg); | |
| mutex_unlock(&mcp->lock); | |
| break; | |
| default: | |
| dev_dbg(mcp->dev, "Invalid config param %04x\n", param); | |
| return -ENOTSUPP; | |
| } | |
| } | |
| return ret; | |
| } | |
| static const struct pinconf_ops mcp_pinconf_ops = { | |
| .pin_config_get = mcp_pinconf_get, | |
| .pin_config_set = mcp_pinconf_set, | |
| .is_generic = true, | |
| }; | |
| /*----------------------------------------------------------------------*/ | |
| static int mcp23s08_direction_input(struct gpio_chip *chip, unsigned offset) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| int status; | |
| mutex_lock(&mcp->lock); | |
| status = mcp_set_bit(mcp, MCP_IODIR, offset, true); | |
| mutex_unlock(&mcp->lock); | |
| return status; | |
| } | |
| static int mcp23s08_get(struct gpio_chip *chip, unsigned offset) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| int status, ret; | |
| mutex_lock(&mcp->lock); | |
| /* REVISIT reading this clears any IRQ ... */ | |
| ret = mcp_read(mcp, MCP_GPIO, &status); | |
| if (ret < 0) | |
| status = 0; | |
| else { | |
| mcp->cached_gpio = status; | |
| status = !!(status & (1 << offset)); | |
| } | |
| mutex_unlock(&mcp->lock); | |
| return status; | |
| } | |
| static int mcp23s08_get_multiple(struct gpio_chip *chip, | |
| unsigned long *mask, unsigned long *bits) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| unsigned int status; | |
| int ret; | |
| mutex_lock(&mcp->lock); | |
| /* REVISIT reading this clears any IRQ ... */ | |
| ret = mcp_read(mcp, MCP_GPIO, &status); | |
| if (ret < 0) | |
| status = 0; | |
| else { | |
| mcp->cached_gpio = status; | |
| *bits = status; | |
| } | |
| mutex_unlock(&mcp->lock); | |
| return ret; | |
| } | |
| static int __mcp23s08_set(struct mcp23s08 *mcp, unsigned mask, bool value) | |
| { | |
| return mcp_update_bits(mcp, MCP_OLAT, mask, value ? mask : 0); | |
| } | |
| static int mcp23s08_set(struct gpio_chip *chip, unsigned int offset, int value) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| unsigned mask = BIT(offset); | |
| int ret; | |
| mutex_lock(&mcp->lock); | |
| ret = __mcp23s08_set(mcp, mask, !!value); | |
| mutex_unlock(&mcp->lock); | |
| return ret; | |
| } | |
| static int mcp23s08_set_multiple(struct gpio_chip *chip, | |
| unsigned long *mask, unsigned long *bits) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| int ret; | |
| mutex_lock(&mcp->lock); | |
| ret = mcp_update_bits(mcp, MCP_OLAT, *mask, *bits); | |
| mutex_unlock(&mcp->lock); | |
| return ret; | |
| } | |
| static int | |
| mcp23s08_direction_output(struct gpio_chip *chip, unsigned offset, int value) | |
| { | |
| struct mcp23s08 *mcp = gpiochip_get_data(chip); | |
| unsigned mask = BIT(offset); | |
| int status; | |
| mutex_lock(&mcp->lock); | |
| status = __mcp23s08_set(mcp, mask, value); | |
| if (status == 0) { | |
| status = mcp_update_bits(mcp, MCP_IODIR, mask, 0); | |
| } | |
| mutex_unlock(&mcp->lock); | |
| return status; | |
| } | |
| /*----------------------------------------------------------------------*/ | |
| static irqreturn_t mcp23s08_irq(int irq, void *data) | |
| { | |
| struct mcp23s08 *mcp = data; | |
| int intcap, intcon, intf, i, gpio, gpio_orig, intcap_mask, defval, gpinten; | |
| bool need_unmask = false; | |
| unsigned long int enabled_interrupts; | |
| unsigned int child_irq; | |
| bool intf_set, intcap_changed, gpio_bit_changed, | |
| defval_changed, gpio_set; | |
| mutex_lock(&mcp->lock); | |
| if (mcp_read(mcp, MCP_INTF, &intf)) | |
| goto unlock; | |
| if (intf == 0) { | |
| /* There is no interrupt pending */ | |
| goto unlock; | |
| } | |
| if (mcp_read(mcp, MCP_INTCON, &intcon)) | |
| goto unlock; | |
| if (mcp_read(mcp, MCP_GPINTEN, &gpinten)) | |
| goto unlock; | |
| if (mcp_read(mcp, MCP_DEFVAL, &defval)) | |
| goto unlock; | |
| /* Mask level interrupts to avoid their immediate reactivation after clearing */ | |
| if (intcon) { | |
| need_unmask = true; | |
| if (mcp_write(mcp, MCP_GPINTEN, gpinten & ~intcon)) | |
| goto unlock; | |
| } | |
| if (mcp_read(mcp, MCP_INTCAP, &intcap)) | |
| goto unlock; | |
| /* This clears the interrupt(configurable on S18) */ | |
| if (mcp_read(mcp, MCP_GPIO, &gpio)) | |
| goto unlock; | |
| gpio_orig = mcp->cached_gpio; | |
| mcp->cached_gpio = gpio; | |
| mutex_unlock(&mcp->lock); | |
| dev_dbg(mcp->chip.parent, | |
| "intcap 0x%04X intf 0x%04X gpio_orig 0x%04X gpio 0x%04X\n", | |
| intcap, intf, gpio_orig, gpio); | |
| enabled_interrupts = gpinten; | |
| for_each_set_bit(i, &enabled_interrupts, mcp->chip.ngpio) { | |
| /* | |
| * We must check all of the inputs with enabled interrupts | |
| * on the chip, otherwise we may not notice a change | |
| * on more than one pin. | |
| * | |
| * On at least the mcp23s17, INTCAP is only updated | |
| * one byte at a time(INTCAPA and INTCAPB are | |
| * not written to at the same time - only on a per-bank | |
| * basis). | |
| * | |
| * INTF only contains the single bit that caused the | |
| * interrupt per-bank. On the mcp23s17, there is | |
| * INTFA and INTFB. If two pins are changed on the A | |
| * side at the same time, INTF will only have one bit | |
| * set. If one pin on the A side and one pin on the B | |
| * side are changed at the same time, INTF will have | |
| * two bits set. Thus, INTF can't be the only check | |
| * to see if the input has changed. | |
| */ | |
| intf_set = intf & BIT(i); | |
| if (i < 8 && intf_set) | |
| intcap_mask = 0x00FF; | |
| else if (i >= 8 && intf_set) | |
| intcap_mask = 0xFF00; | |
| else | |
| intcap_mask = 0x00; | |
| intcap_changed = (intcap_mask & | |
| (intcap & BIT(i))) != | |
| (intcap_mask & (BIT(i) & gpio_orig)); | |
| gpio_set = BIT(i) & gpio; | |
| gpio_bit_changed = (BIT(i) & gpio_orig) != | |
| (BIT(i) & gpio); | |
| defval_changed = (BIT(i) & intcon) && | |
| ((BIT(i) & gpio) != | |
| (BIT(i) & defval)); | |
| if (((gpio_bit_changed || intcap_changed) && | |
| (BIT(i) & mcp->irq_rise) && gpio_set) || | |
| ((gpio_bit_changed || intcap_changed) && | |
| (BIT(i) & mcp->irq_fall) && !gpio_set) || | |
| defval_changed) { | |
| child_irq = irq_find_mapping(mcp->chip.irq.domain, i); | |
| handle_nested_irq(child_irq); | |
| } | |
| } | |
| if (need_unmask) { | |
| mutex_lock(&mcp->lock); | |
| goto unlock; | |
| } | |
| return IRQ_HANDLED; | |
| unlock: | |
| if (need_unmask) | |
| if (mcp_write(mcp, MCP_GPINTEN, gpinten)) | |
| dev_err(mcp->chip.parent, "can't unmask GPINTEN\n"); | |
| mutex_unlock(&mcp->lock); | |
| return IRQ_HANDLED; | |
| } | |
| static void mcp23s08_irq_mask(struct irq_data *data) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(data); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| unsigned int pos = irqd_to_hwirq(data); | |
| mcp_set_bit(mcp, MCP_GPINTEN, pos, false); | |
| gpiochip_disable_irq(gc, pos); | |
| } | |
| static void mcp23s08_irq_unmask(struct irq_data *data) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(data); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| unsigned int pos = irqd_to_hwirq(data); | |
| gpiochip_enable_irq(gc, pos); | |
| mcp_set_bit(mcp, MCP_GPINTEN, pos, true); | |
| } | |
| static int mcp23s08_irq_set_type(struct irq_data *data, unsigned int type) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(data); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| unsigned int pos = irqd_to_hwirq(data); | |
| if ((type & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) { | |
| mcp_set_bit(mcp, MCP_INTCON, pos, false); | |
| mcp->irq_rise |= BIT(pos); | |
| mcp->irq_fall |= BIT(pos); | |
| } else if (type & IRQ_TYPE_EDGE_RISING) { | |
| mcp_set_bit(mcp, MCP_INTCON, pos, false); | |
| mcp->irq_rise |= BIT(pos); | |
| mcp->irq_fall &= ~BIT(pos); | |
| } else if (type & IRQ_TYPE_EDGE_FALLING) { | |
| mcp_set_bit(mcp, MCP_INTCON, pos, false); | |
| mcp->irq_rise &= ~BIT(pos); | |
| mcp->irq_fall |= BIT(pos); | |
| } else if (type & IRQ_TYPE_LEVEL_HIGH) { | |
| mcp_set_bit(mcp, MCP_INTCON, pos, true); | |
| mcp_set_bit(mcp, MCP_DEFVAL, pos, false); | |
| } else if (type & IRQ_TYPE_LEVEL_LOW) { | |
| mcp_set_bit(mcp, MCP_INTCON, pos, true); | |
| mcp_set_bit(mcp, MCP_DEFVAL, pos, true); | |
| } else | |
| return -EINVAL; | |
| return 0; | |
| } | |
| static void mcp23s08_irq_bus_lock(struct irq_data *data) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(data); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| mutex_lock(&mcp->lock); | |
| regcache_cache_only(mcp->regmap, true); | |
| } | |
| static void mcp23s08_irq_bus_unlock(struct irq_data *data) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(data); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| regcache_cache_only(mcp->regmap, false); | |
| regcache_sync(mcp->regmap); | |
| mutex_unlock(&mcp->lock); | |
| } | |
| static int mcp23s08_irq_setup(struct mcp23s08 *mcp) | |
| { | |
| struct gpio_chip *chip = &mcp->chip; | |
| int err; | |
| unsigned long irqflags = IRQF_ONESHOT | IRQF_SHARED; | |
| if (mcp->irq_active_high) | |
| irqflags |= IRQF_TRIGGER_HIGH; | |
| else | |
| irqflags |= IRQF_TRIGGER_LOW; | |
| err = devm_request_threaded_irq(chip->parent, mcp->irq, NULL, | |
| mcp23s08_irq, | |
| irqflags, dev_name(chip->parent), mcp); | |
| if (err) | |
| return err; | |
| return 0; | |
| } | |
| static void mcp23s08_irq_print_chip(struct irq_data *d, struct seq_file *p) | |
| { | |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | |
| struct mcp23s08 *mcp = gpiochip_get_data(gc); | |
| seq_puts(p, dev_name(mcp->dev)); | |
| } | |
| static const struct irq_chip mcp23s08_irq_chip = { | |
| .irq_mask = mcp23s08_irq_mask, | |
| .irq_unmask = mcp23s08_irq_unmask, | |
| .irq_set_type = mcp23s08_irq_set_type, | |
| .irq_bus_lock = mcp23s08_irq_bus_lock, | |
| .irq_bus_sync_unlock = mcp23s08_irq_bus_unlock, | |
| .irq_print_chip = mcp23s08_irq_print_chip, | |
| .flags = IRQCHIP_IMMUTABLE, | |
| GPIOCHIP_IRQ_RESOURCE_HELPERS, | |
| }; | |
| /*----------------------------------------------------------------------*/ | |
| int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, | |
| unsigned int addr, unsigned int type, unsigned int base) | |
| { | |
| int status, ret; | |
| bool mirror = false; | |
| bool open_drain = false; | |
| mutex_init(&mcp->lock); | |
| mcp->dev = dev; | |
| mcp->addr = addr; | |
| mcp->irq_active_high = false; | |
| mcp->chip.direction_input = mcp23s08_direction_input; | |
| mcp->chip.get = mcp23s08_get; | |
| mcp->chip.get_multiple = mcp23s08_get_multiple; | |
| mcp->chip.direction_output = mcp23s08_direction_output; | |
| mcp->chip.set = mcp23s08_set; | |
| mcp->chip.set_multiple = mcp23s08_set_multiple; | |
| mcp->chip.base = base; | |
| mcp->chip.can_sleep = true; | |
| mcp->chip.parent = dev; | |
| mcp->chip.owner = THIS_MODULE; | |
| mcp->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); | |
| /* verify MCP_IOCON.SEQOP = 0, so sequential reads work, | |
| * and MCP_IOCON.HAEN = 1, so we work with all chips. | |
| */ | |
| ret = mcp_read(mcp, MCP_IOCON, &status); | |
| if (ret < 0) | |
| return dev_err_probe(dev, ret, "can't identify chip %d\n", addr); | |
| mcp->irq_controller = | |
| device_property_read_bool(dev, "interrupt-controller"); | |
| if (mcp->irq && mcp->irq_controller) { | |
| mcp->irq_active_high = | |
| device_property_read_bool(dev, | |
| "microchip,irq-active-high"); | |
| mirror = device_property_read_bool(dev, "microchip,irq-mirror"); | |
| open_drain = device_property_read_bool(dev, "drive-open-drain"); | |
| } | |
| if ((status & IOCON_SEQOP) || !(status & IOCON_HAEN) || mirror || | |
| mcp->irq_active_high || open_drain) { | |
| /* mcp23s17 has IOCON twice, make sure they are in sync */ | |
| status &= ~(IOCON_SEQOP | (IOCON_SEQOP << 8)); | |
| status |= IOCON_HAEN | (IOCON_HAEN << 8); | |
| if (mcp->irq_active_high) | |
| status |= IOCON_INTPOL | (IOCON_INTPOL << 8); | |
| else | |
| status &= ~(IOCON_INTPOL | (IOCON_INTPOL << 8)); | |
| if (mirror) | |
| status |= IOCON_MIRROR | (IOCON_MIRROR << 8); | |
| if (open_drain) | |
| status |= IOCON_ODR | (IOCON_ODR << 8); | |
| if (type == MCP_TYPE_S18 || type == MCP_TYPE_018) | |
| status |= IOCON_INTCC | (IOCON_INTCC << 8); | |
| ret = mcp_write(mcp, MCP_IOCON, status); | |
| if (ret < 0) | |
| return dev_err_probe(dev, ret, "can't write IOCON %d\n", addr); | |
| } | |
| if (mcp->irq && mcp->irq_controller) { | |
| struct gpio_irq_chip *girq = &mcp->chip.irq; | |
| /* | |
| * Disable all pin interrupts, to prevent the interrupt handler from | |
| * calling nested handlers for any currently-enabled interrupts that | |
| * do not (yet) have an actual handler. | |
| */ | |
| ret = mcp_write(mcp, MCP_GPINTEN, 0); | |
| if (ret < 0) | |
| return dev_err_probe(dev, ret, "can't disable interrupts\n"); | |
| gpio_irq_chip_set_chip(girq, &mcp23s08_irq_chip); | |
| /* This will let us handle the parent IRQ in the driver */ | |
| girq->parent_handler = NULL; | |
| girq->num_parents = 0; | |
| girq->parents = NULL; | |
| girq->default_type = IRQ_TYPE_NONE; | |
| girq->handler = handle_simple_irq; | |
| girq->threaded = true; | |
| } | |
| ret = devm_gpiochip_add_data(dev, &mcp->chip, mcp); | |
| if (ret < 0) | |
| return dev_err_probe(dev, ret, "can't add GPIO chip\n"); | |
| mcp->pinctrl_desc.pctlops = &mcp_pinctrl_ops; | |
| mcp->pinctrl_desc.confops = &mcp_pinconf_ops; | |
| mcp->pinctrl_desc.npins = mcp->chip.ngpio; | |
| if (mcp->pinctrl_desc.npins == 8) | |
| mcp->pinctrl_desc.pins = mcp23x08_pins; | |
| else if (mcp->pinctrl_desc.npins == 16) | |
| mcp->pinctrl_desc.pins = mcp23x17_pins; | |
| mcp->pinctrl_desc.owner = THIS_MODULE; | |
| mcp->pctldev = devm_pinctrl_register(dev, &mcp->pinctrl_desc, mcp); | |
| if (IS_ERR(mcp->pctldev)) | |
| return dev_err_probe(dev, PTR_ERR(mcp->pctldev), "can't register controller\n"); | |
| if (mcp->irq) { | |
| ret = mcp23s08_irq_setup(mcp); | |
| if (ret) | |
| return dev_err_probe(dev, ret, "can't setup IRQ\n"); | |
| } | |
| return 0; | |
| } | |
| EXPORT_SYMBOL_GPL(mcp23s08_probe_one); | |
| MODULE_DESCRIPTION("MCP23S08 SPI/I2C GPIO driver"); | |
| MODULE_LICENSE("GPL"); |