| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * PCIe driver for Renesas R-Car SoCs | |
| * Copyright (C) 2014-2020 Renesas Electronics Europe Ltd | |
| * | |
| * Based on: | |
| * arch/sh/drivers/pci/pcie-sh7786.c | |
| * arch/sh/drivers/pci/ops-sh7786.c | |
| * Copyright (C) 2009 - 2011 Paul Mundt | |
| * | |
| * Author: Phil Edworthy <phil.edworthy@renesas.com> | |
| */ | |
| #include <linux/bitops.h> | |
| #include <linux/cleanup.h> | |
| #include <linux/clk.h> | |
| #include <linux/clk-provider.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/irqchip/irq-msi-lib.h> | |
| #include <linux/irqdomain.h> | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/msi.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/pci.h> | |
| #include <linux/phy/phy.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/regulator/consumer.h> | |
| #include "pcie-rcar.h" | |
| struct rcar_msi { | |
| DECLARE_BITMAP(used, INT_PCI_MSI_NR); | |
| struct irq_domain *domain; | |
| struct mutex map_lock; | |
| raw_spinlock_t mask_lock; | |
| int irq1; | |
| int irq2; | |
| }; | |
| /* Structure representing the PCIe interface */ | |
| struct rcar_pcie_host { | |
| struct rcar_pcie pcie; | |
| struct phy *phy; | |
| struct clk *bus_clk; | |
| struct rcar_msi msi; | |
| int (*phy_init_fn)(struct rcar_pcie_host *host); | |
| }; | |
| static int rcar_pcie_wakeup(struct device *pcie_dev, void __iomem *pcie_base) | |
| { | |
| u32 pmsr, val; | |
| int ret = 0; | |
| if (!pcie_base || pm_runtime_suspended(pcie_dev)) | |
| return -EINVAL; | |
| pmsr = readl(pcie_base + PMSR); | |
| /* | |
| * Test if the PCIe controller received PM_ENTER_L1 DLLP and | |
| * the PCIe controller is not in L1 link state. If true, apply | |
| * fix, which will put the controller into L1 link state, from | |
| * which it can return to L0s/L0 on its own. | |
| */ | |
| if ((pmsr & PMEL1RX) && ((pmsr & PMSTATE) != PMSTATE_L1)) { | |
| writel(L1IATN, pcie_base + PMCTLR); | |
| ret = readl_poll_timeout_atomic(pcie_base + PMSR, val, | |
| val & L1FAEG, 10, 1000); | |
| if (ret) { | |
| dev_warn_ratelimited(pcie_dev, | |
| "Timeout waiting for L1 link state, ret=%d\n", | |
| ret); | |
| } | |
| writel(L1FAEG | PMEL1RX, pcie_base + PMSR); | |
| } | |
| return ret; | |
| } | |
| static struct rcar_pcie_host *msi_to_host(struct rcar_msi *msi) | |
| { | |
| return container_of(msi, struct rcar_pcie_host, msi); | |
| } | |
| static u32 rcar_read_conf(struct rcar_pcie *pcie, int where) | |
| { | |
| unsigned int shift = BITS_PER_BYTE * (where & 3); | |
| u32 val = rcar_pci_read_reg(pcie, where & ~3); | |
| return val >> shift; | |
| } | |
| #ifdef CONFIG_ARM | |
| #define __rcar_pci_rw_reg_workaround(instr) \ | |
| " .arch armv7-a\n" \ | |
| "1: " instr " %1, [%2]\n" \ | |
| "2: isb\n" \ | |
| "3: .pushsection .text.fixup,\"ax\"\n" \ | |
| " .align 2\n" \ | |
| "4: mov %0, #" __stringify(PCIBIOS_SET_FAILED) "\n" \ | |
| " b 3b\n" \ | |
| " .popsection\n" \ | |
| " .pushsection __ex_table,\"a\"\n" \ | |
| " .align 3\n" \ | |
| " .long 1b, 4b\n" \ | |
| " .long 2b, 4b\n" \ | |
| " .popsection\n" | |
| #endif | |
| static int rcar_pci_write_reg_workaround(struct rcar_pcie *pcie, u32 val, | |
| unsigned int reg) | |
| { | |
| int error = PCIBIOS_SUCCESSFUL; | |
| #ifdef CONFIG_ARM | |
| asm volatile( | |
| __rcar_pci_rw_reg_workaround("str") | |
| : "+r"(error):"r"(val), "r"(pcie->base + reg) : "memory"); | |
| #else | |
| rcar_pci_write_reg(pcie, val, reg); | |
| #endif | |
| return error; | |
| } | |
| static int rcar_pci_read_reg_workaround(struct rcar_pcie *pcie, u32 *val, | |
| unsigned int reg) | |
| { | |
| int error = PCIBIOS_SUCCESSFUL; | |
| #ifdef CONFIG_ARM | |
| asm volatile( | |
| __rcar_pci_rw_reg_workaround("ldr") | |
| : "+r"(error), "=r"(*val) : "r"(pcie->base + reg) : "memory"); | |
| if (error != PCIBIOS_SUCCESSFUL) | |
| PCI_SET_ERROR_RESPONSE(val); | |
| #else | |
| *val = rcar_pci_read_reg(pcie, reg); | |
| #endif | |
| return error; | |
| } | |
| /* Serialization is provided by 'pci_lock' in drivers/pci/access.c */ | |
| static int rcar_pcie_config_access(struct rcar_pcie_host *host, | |
| unsigned char access_type, struct pci_bus *bus, | |
| unsigned int devfn, int where, u32 *data) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| unsigned int dev, func, reg, index; | |
| int ret; | |
| /* Wake the bus up in case it is in L1 state. */ | |
| ret = rcar_pcie_wakeup(pcie->dev, pcie->base); | |
| if (ret) { | |
| PCI_SET_ERROR_RESPONSE(data); | |
| return PCIBIOS_SET_FAILED; | |
| } | |
| dev = PCI_SLOT(devfn); | |
| func = PCI_FUNC(devfn); | |
| reg = where & ~3; | |
| index = reg / 4; | |
| /* | |
| * While each channel has its own memory-mapped extended config | |
| * space, it's generally only accessible when in endpoint mode. | |
| * When in root complex mode, the controller is unable to target | |
| * itself with either type 0 or type 1 accesses, and indeed, any | |
| * controller-initiated target transfer to its own config space | |
| * results in a completer abort. | |
| * | |
| * Each channel effectively only supports a single device, but as | |
| * the same channel <-> device access works for any PCI_SLOT() | |
| * value, we cheat a bit here and bind the controller's config | |
| * space to devfn 0 in order to enable self-enumeration. In this | |
| * case the regular ECAR/ECDR path is sidelined and the mangled | |
| * config access itself is initiated as an internal bus transaction. | |
| */ | |
| if (pci_is_root_bus(bus)) { | |
| if (dev != 0) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| if (access_type == RCAR_PCI_ACCESS_READ) | |
| *data = rcar_pci_read_reg(pcie, PCICONF(index)); | |
| else | |
| rcar_pci_write_reg(pcie, *data, PCICONF(index)); | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| /* Clear errors */ | |
| rcar_pci_write_reg(pcie, rcar_pci_read_reg(pcie, PCIEERRFR), PCIEERRFR); | |
| /* Set the PIO address */ | |
| rcar_pci_write_reg(pcie, PCIE_CONF_BUS(bus->number) | | |
| PCIE_CONF_DEV(dev) | PCIE_CONF_FUNC(func) | reg, PCIECAR); | |
| /* Enable the configuration access */ | |
| if (pci_is_root_bus(bus->parent)) | |
| rcar_pci_write_reg(pcie, PCIECCTLR_CCIE | TYPE0, PCIECCTLR); | |
| else | |
| rcar_pci_write_reg(pcie, PCIECCTLR_CCIE | TYPE1, PCIECCTLR); | |
| /* Check for errors */ | |
| if (rcar_pci_read_reg(pcie, PCIEERRFR) & UNSUPPORTED_REQUEST) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| /* Check for master and target aborts */ | |
| if (rcar_read_conf(pcie, RCONF(PCI_STATUS)) & | |
| (PCI_STATUS_REC_MASTER_ABORT | PCI_STATUS_REC_TARGET_ABORT)) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| if (access_type == RCAR_PCI_ACCESS_READ) | |
| ret = rcar_pci_read_reg_workaround(pcie, data, PCIECDR); | |
| else | |
| ret = rcar_pci_write_reg_workaround(pcie, *data, PCIECDR); | |
| /* Disable the configuration access */ | |
| rcar_pci_write_reg(pcie, 0, PCIECCTLR); | |
| return ret; | |
| } | |
| static int rcar_pcie_read_conf(struct pci_bus *bus, unsigned int devfn, | |
| int where, int size, u32 *val) | |
| { | |
| struct rcar_pcie_host *host = bus->sysdata; | |
| int ret; | |
| ret = rcar_pcie_config_access(host, RCAR_PCI_ACCESS_READ, | |
| bus, devfn, where, val); | |
| if (ret != PCIBIOS_SUCCESSFUL) | |
| return ret; | |
| if (size == 1) | |
| *val = (*val >> (BITS_PER_BYTE * (where & 3))) & 0xff; | |
| else if (size == 2) | |
| *val = (*val >> (BITS_PER_BYTE * (where & 2))) & 0xffff; | |
| dev_dbg(&bus->dev, "pcie-config-read: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n", | |
| bus->number, devfn, where, size, *val); | |
| return ret; | |
| } | |
| /* Serialization is provided by 'pci_lock' in drivers/pci/access.c */ | |
| static int rcar_pcie_write_conf(struct pci_bus *bus, unsigned int devfn, | |
| int where, int size, u32 val) | |
| { | |
| struct rcar_pcie_host *host = bus->sysdata; | |
| unsigned int shift; | |
| u32 data; | |
| int ret; | |
| ret = rcar_pcie_config_access(host, RCAR_PCI_ACCESS_READ, | |
| bus, devfn, where, &data); | |
| if (ret != PCIBIOS_SUCCESSFUL) | |
| return ret; | |
| dev_dbg(&bus->dev, "pcie-config-write: bus=%3d devfn=0x%04x where=0x%04x size=%d val=0x%08x\n", | |
| bus->number, devfn, where, size, val); | |
| if (size == 1) { | |
| shift = BITS_PER_BYTE * (where & 3); | |
| data &= ~(0xff << shift); | |
| data |= ((val & 0xff) << shift); | |
| } else if (size == 2) { | |
| shift = BITS_PER_BYTE * (where & 2); | |
| data &= ~(0xffff << shift); | |
| data |= ((val & 0xffff) << shift); | |
| } else | |
| data = val; | |
| ret = rcar_pcie_config_access(host, RCAR_PCI_ACCESS_WRITE, | |
| bus, devfn, where, &data); | |
| return ret; | |
| } | |
| static struct pci_ops rcar_pcie_ops = { | |
| .read = rcar_pcie_read_conf, | |
| .write = rcar_pcie_write_conf, | |
| }; | |
| static void rcar_pcie_force_speedup(struct rcar_pcie *pcie) | |
| { | |
| struct device *dev = pcie->dev; | |
| unsigned int timeout = 1000; | |
| u32 macsr; | |
| if ((rcar_pci_read_reg(pcie, MACS2R) & LINK_SPEED) != LINK_SPEED_5_0GTS) | |
| return; | |
| if (rcar_pci_read_reg(pcie, MACCTLR) & SPEED_CHANGE) { | |
| dev_err(dev, "Speed change already in progress\n"); | |
| return; | |
| } | |
| macsr = rcar_pci_read_reg(pcie, MACSR); | |
| if ((macsr & LINK_SPEED) == LINK_SPEED_5_0GTS) | |
| goto done; | |
| /* Set target link speed to 5.0 GT/s */ | |
| rcar_rmw32(pcie, EXPCAP(12), PCI_EXP_LNKSTA_CLS, | |
| PCI_EXP_LNKSTA_CLS_5_0GB); | |
| /* Set speed change reason as intentional factor */ | |
| rcar_rmw32(pcie, MACCGSPSETR, SPCNGRSN, 0); | |
| /* Clear SPCHGFIN, SPCHGSUC, and SPCHGFAIL */ | |
| if (macsr & (SPCHGFIN | SPCHGSUC | SPCHGFAIL)) | |
| rcar_pci_write_reg(pcie, macsr, MACSR); | |
| /* Start link speed change */ | |
| rcar_rmw32(pcie, MACCTLR, SPEED_CHANGE, SPEED_CHANGE); | |
| while (timeout--) { | |
| macsr = rcar_pci_read_reg(pcie, MACSR); | |
| if (macsr & SPCHGFIN) { | |
| /* Clear the interrupt bits */ | |
| rcar_pci_write_reg(pcie, macsr, MACSR); | |
| if (macsr & SPCHGFAIL) | |
| dev_err(dev, "Speed change failed\n"); | |
| goto done; | |
| } | |
| msleep(1); | |
| } | |
| dev_err(dev, "Speed change timed out\n"); | |
| done: | |
| dev_info(dev, "Current link speed is %s GT/s\n", | |
| (macsr & LINK_SPEED) == LINK_SPEED_5_0GTS ? "5" : "2.5"); | |
| } | |
| static void rcar_pcie_hw_enable(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(host); | |
| struct resource_entry *win; | |
| int i = 0; | |
| /* Try setting 5 GT/s link speed */ | |
| rcar_pcie_force_speedup(pcie); | |
| /* Setup PCI resources */ | |
| resource_list_for_each_entry(win, &bridge->windows) { | |
| struct resource *res = win->res; | |
| if (!res->flags) | |
| continue; | |
| switch (resource_type(res)) { | |
| case IORESOURCE_IO: | |
| case IORESOURCE_MEM: | |
| rcar_pcie_set_outbound(pcie, i, win); | |
| i++; | |
| break; | |
| } | |
| } | |
| } | |
| static int rcar_pcie_enable(struct rcar_pcie_host *host) | |
| { | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(host); | |
| rcar_pcie_hw_enable(host); | |
| pci_add_flags(PCI_REASSIGN_ALL_BUS); | |
| bridge->sysdata = host; | |
| bridge->ops = &rcar_pcie_ops; | |
| return pci_host_probe(bridge); | |
| } | |
| static int phy_wait_for_ack(struct rcar_pcie *pcie) | |
| { | |
| struct device *dev = pcie->dev; | |
| unsigned int timeout = 100; | |
| while (timeout--) { | |
| if (rcar_pci_read_reg(pcie, H1_PCIEPHYADRR) & PHY_ACK) | |
| return 0; | |
| udelay(100); | |
| } | |
| dev_err(dev, "Access to PCIe phy timed out\n"); | |
| return -ETIMEDOUT; | |
| } | |
| static void phy_write_reg(struct rcar_pcie *pcie, | |
| unsigned int rate, u32 addr, | |
| unsigned int lane, u32 data) | |
| { | |
| u32 phyaddr; | |
| phyaddr = WRITE_CMD | | |
| ((rate & 1) << RATE_POS) | | |
| ((lane & 0xf) << LANE_POS) | | |
| ((addr & 0xff) << ADR_POS); | |
| /* Set write data */ | |
| rcar_pci_write_reg(pcie, data, H1_PCIEPHYDOUTR); | |
| rcar_pci_write_reg(pcie, phyaddr, H1_PCIEPHYADRR); | |
| /* Ignore errors as they will be dealt with if the data link is down */ | |
| phy_wait_for_ack(pcie); | |
| /* Clear command */ | |
| rcar_pci_write_reg(pcie, 0, H1_PCIEPHYDOUTR); | |
| rcar_pci_write_reg(pcie, 0, H1_PCIEPHYADRR); | |
| /* Ignore errors as they will be dealt with if the data link is down */ | |
| phy_wait_for_ack(pcie); | |
| } | |
| static int rcar_pcie_hw_init(struct rcar_pcie *pcie) | |
| { | |
| int err; | |
| /* Begin initialization */ | |
| rcar_pci_write_reg(pcie, 0, PCIETCTLR); | |
| /* Set mode */ | |
| rcar_pci_write_reg(pcie, 1, PCIEMSR); | |
| err = rcar_pcie_wait_for_phyrdy(pcie); | |
| if (err) | |
| return err; | |
| /* | |
| * Initial header for port config space is type 1, set the device | |
| * class to match. Hardware takes care of propagating the IDSETR | |
| * settings, so there is no need to bother with a quirk. | |
| */ | |
| rcar_pci_write_reg(pcie, PCI_CLASS_BRIDGE_PCI_NORMAL << 8, IDSETR1); | |
| /* | |
| * Setup Secondary Bus Number & Subordinate Bus Number, even though | |
| * they aren't used, to avoid bridge being detected as broken. | |
| */ | |
| rcar_rmw32(pcie, RCONF(PCI_SECONDARY_BUS), 0xff, 1); | |
| rcar_rmw32(pcie, RCONF(PCI_SUBORDINATE_BUS), 0xff, 1); | |
| /* Initialize default capabilities. */ | |
| rcar_rmw32(pcie, REXPCAP(0), 0xff, PCI_CAP_ID_EXP); | |
| rcar_rmw32(pcie, REXPCAP(PCI_EXP_FLAGS), | |
| PCI_EXP_FLAGS_TYPE, PCI_EXP_TYPE_ROOT_PORT << 4); | |
| rcar_rmw32(pcie, RCONF(PCI_HEADER_TYPE), PCI_HEADER_TYPE_MASK, | |
| PCI_HEADER_TYPE_BRIDGE); | |
| /* Enable data link layer active state reporting */ | |
| rcar_rmw32(pcie, REXPCAP(PCI_EXP_LNKCAP), PCI_EXP_LNKCAP_DLLLARC, | |
| PCI_EXP_LNKCAP_DLLLARC); | |
| /* Write out the physical slot number = 0 */ | |
| rcar_rmw32(pcie, REXPCAP(PCI_EXP_SLTCAP), PCI_EXP_SLTCAP_PSN, 0); | |
| /* Set the completion timer timeout to the maximum 50ms. */ | |
| rcar_rmw32(pcie, TLCTLR + 1, 0x3f, 50); | |
| /* Terminate list of capabilities (Next Capability Offset=0) */ | |
| rcar_rmw32(pcie, RVCCAP(0), 0xfff00000, 0); | |
| /* Enable MSI */ | |
| if (IS_ENABLED(CONFIG_PCI_MSI)) | |
| rcar_pci_write_reg(pcie, 0x801f0000, PCIEMSITXR); | |
| rcar_pci_write_reg(pcie, MACCTLR_INIT_VAL, MACCTLR); | |
| /* Finish initialization - establish a PCI Express link */ | |
| rcar_pci_write_reg(pcie, CFINIT, PCIETCTLR); | |
| /* This will timeout if we don't have a link. */ | |
| err = rcar_pcie_wait_for_dl(pcie); | |
| if (err) | |
| return err; | |
| /* Enable INTx interrupts */ | |
| rcar_rmw32(pcie, PCIEINTXR, 0, 0xF << 8); | |
| wmb(); | |
| return 0; | |
| } | |
| static int rcar_pcie_phy_init_h1(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| /* Initialize the phy */ | |
| phy_write_reg(pcie, 0, 0x42, 0x1, 0x0EC34191); | |
| phy_write_reg(pcie, 1, 0x42, 0x1, 0x0EC34180); | |
| phy_write_reg(pcie, 0, 0x43, 0x1, 0x00210188); | |
| phy_write_reg(pcie, 1, 0x43, 0x1, 0x00210188); | |
| phy_write_reg(pcie, 0, 0x44, 0x1, 0x015C0014); | |
| phy_write_reg(pcie, 1, 0x44, 0x1, 0x015C0014); | |
| phy_write_reg(pcie, 1, 0x4C, 0x1, 0x786174A0); | |
| phy_write_reg(pcie, 1, 0x4D, 0x1, 0x048000BB); | |
| phy_write_reg(pcie, 0, 0x51, 0x1, 0x079EC062); | |
| phy_write_reg(pcie, 0, 0x52, 0x1, 0x20000000); | |
| phy_write_reg(pcie, 1, 0x52, 0x1, 0x20000000); | |
| phy_write_reg(pcie, 1, 0x56, 0x1, 0x00003806); | |
| phy_write_reg(pcie, 0, 0x60, 0x1, 0x004B03A5); | |
| phy_write_reg(pcie, 0, 0x64, 0x1, 0x3F0F1F0F); | |
| phy_write_reg(pcie, 0, 0x66, 0x1, 0x00008000); | |
| return 0; | |
| } | |
| static int rcar_pcie_phy_init_gen2(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| /* | |
| * These settings come from the R-Car Series, 2nd Generation User's | |
| * Manual, section 50.3.1 (2) Initialization of the physical layer. | |
| */ | |
| rcar_pci_write_reg(pcie, 0x000f0030, GEN2_PCIEPHYADDR); | |
| rcar_pci_write_reg(pcie, 0x00381203, GEN2_PCIEPHYDATA); | |
| rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL); | |
| rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL); | |
| rcar_pci_write_reg(pcie, 0x000f0054, GEN2_PCIEPHYADDR); | |
| /* The following value is for DC connection, no termination resistor */ | |
| rcar_pci_write_reg(pcie, 0x13802007, GEN2_PCIEPHYDATA); | |
| rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL); | |
| rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL); | |
| return 0; | |
| } | |
| static int rcar_pcie_phy_init_gen3(struct rcar_pcie_host *host) | |
| { | |
| int err; | |
| err = phy_init(host->phy); | |
| if (err) | |
| return err; | |
| err = phy_power_on(host->phy); | |
| if (err) | |
| phy_exit(host->phy); | |
| return err; | |
| } | |
| static irqreturn_t rcar_pcie_msi_irq(int irq, void *data) | |
| { | |
| struct rcar_pcie_host *host = data; | |
| struct rcar_pcie *pcie = &host->pcie; | |
| struct rcar_msi *msi = &host->msi; | |
| struct device *dev = pcie->dev; | |
| unsigned long reg; | |
| reg = rcar_pci_read_reg(pcie, PCIEMSIFR); | |
| /* MSI & INTx share an interrupt - we only handle MSI here */ | |
| if (!reg) | |
| return IRQ_NONE; | |
| while (reg) { | |
| unsigned int index = find_first_bit(®, 32); | |
| int ret; | |
| ret = generic_handle_domain_irq(msi->domain, index); | |
| if (ret) { | |
| /* Unknown MSI, just clear it */ | |
| dev_dbg(dev, "unexpected MSI\n"); | |
| rcar_pci_write_reg(pcie, BIT(index), PCIEMSIFR); | |
| } | |
| /* see if there's any more pending in this vector */ | |
| reg = rcar_pci_read_reg(pcie, PCIEMSIFR); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static void rcar_msi_irq_ack(struct irq_data *d) | |
| { | |
| struct rcar_msi *msi = irq_data_get_irq_chip_data(d); | |
| struct rcar_pcie *pcie = &msi_to_host(msi)->pcie; | |
| /* clear the interrupt */ | |
| rcar_pci_write_reg(pcie, BIT(d->hwirq), PCIEMSIFR); | |
| } | |
| static void rcar_msi_irq_mask(struct irq_data *d) | |
| { | |
| struct rcar_msi *msi = irq_data_get_irq_chip_data(d); | |
| struct rcar_pcie *pcie = &msi_to_host(msi)->pcie; | |
| u32 value; | |
| scoped_guard(raw_spinlock_irqsave, &msi->mask_lock) { | |
| value = rcar_pci_read_reg(pcie, PCIEMSIIER); | |
| value &= ~BIT(d->hwirq); | |
| rcar_pci_write_reg(pcie, value, PCIEMSIIER); | |
| } | |
| } | |
| static void rcar_msi_irq_unmask(struct irq_data *d) | |
| { | |
| struct rcar_msi *msi = irq_data_get_irq_chip_data(d); | |
| struct rcar_pcie *pcie = &msi_to_host(msi)->pcie; | |
| u32 value; | |
| scoped_guard(raw_spinlock_irqsave, &msi->mask_lock) { | |
| value = rcar_pci_read_reg(pcie, PCIEMSIIER); | |
| value |= BIT(d->hwirq); | |
| rcar_pci_write_reg(pcie, value, PCIEMSIIER); | |
| } | |
| } | |
| static void rcar_compose_msi_msg(struct irq_data *data, struct msi_msg *msg) | |
| { | |
| struct rcar_msi *msi = irq_data_get_irq_chip_data(data); | |
| struct rcar_pcie *pcie = &msi_to_host(msi)->pcie; | |
| msg->address_lo = rcar_pci_read_reg(pcie, PCIEMSIALR) & ~MSIFE; | |
| msg->address_hi = rcar_pci_read_reg(pcie, PCIEMSIAUR); | |
| msg->data = data->hwirq; | |
| } | |
| static struct irq_chip rcar_msi_bottom_chip = { | |
| .name = "R-Car MSI", | |
| .irq_ack = rcar_msi_irq_ack, | |
| .irq_mask = rcar_msi_irq_mask, | |
| .irq_unmask = rcar_msi_irq_unmask, | |
| .irq_compose_msi_msg = rcar_compose_msi_msg, | |
| }; | |
| static int rcar_msi_domain_alloc(struct irq_domain *domain, unsigned int virq, | |
| unsigned int nr_irqs, void *args) | |
| { | |
| struct rcar_msi *msi = domain->host_data; | |
| unsigned int i; | |
| int hwirq; | |
| mutex_lock(&msi->map_lock); | |
| hwirq = bitmap_find_free_region(msi->used, INT_PCI_MSI_NR, order_base_2(nr_irqs)); | |
| mutex_unlock(&msi->map_lock); | |
| if (hwirq < 0) | |
| return -ENOSPC; | |
| for (i = 0; i < nr_irqs; i++) | |
| irq_domain_set_info(domain, virq + i, hwirq + i, | |
| &rcar_msi_bottom_chip, domain->host_data, | |
| handle_edge_irq, NULL, NULL); | |
| return 0; | |
| } | |
| static void rcar_msi_domain_free(struct irq_domain *domain, unsigned int virq, | |
| unsigned int nr_irqs) | |
| { | |
| struct irq_data *d = irq_domain_get_irq_data(domain, virq); | |
| struct rcar_msi *msi = domain->host_data; | |
| mutex_lock(&msi->map_lock); | |
| bitmap_release_region(msi->used, d->hwirq, order_base_2(nr_irqs)); | |
| mutex_unlock(&msi->map_lock); | |
| } | |
| static const struct irq_domain_ops rcar_msi_domain_ops = { | |
| .alloc = rcar_msi_domain_alloc, | |
| .free = rcar_msi_domain_free, | |
| }; | |
| #define RCAR_MSI_FLAGS_REQUIRED (MSI_FLAG_USE_DEF_DOM_OPS | \ | |
| MSI_FLAG_USE_DEF_CHIP_OPS | \ | |
| MSI_FLAG_PCI_MSI_MASK_PARENT | \ | |
| MSI_FLAG_NO_AFFINITY) | |
| #define RCAR_MSI_FLAGS_SUPPORTED (MSI_GENERIC_FLAGS_MASK | \ | |
| MSI_FLAG_MULTI_PCI_MSI) | |
| static const struct msi_parent_ops rcar_msi_parent_ops = { | |
| .required_flags = RCAR_MSI_FLAGS_REQUIRED, | |
| .supported_flags = RCAR_MSI_FLAGS_SUPPORTED, | |
| .bus_select_token = DOMAIN_BUS_PCI_MSI, | |
| .chip_flags = MSI_CHIP_FLAG_SET_ACK, | |
| .prefix = "RCAR-", | |
| .init_dev_msi_info = msi_lib_init_dev_msi_info, | |
| }; | |
| static int rcar_allocate_domains(struct rcar_msi *msi) | |
| { | |
| struct rcar_pcie *pcie = &msi_to_host(msi)->pcie; | |
| struct irq_domain_info info = { | |
| .fwnode = dev_fwnode(pcie->dev), | |
| .ops = &rcar_msi_domain_ops, | |
| .host_data = msi, | |
| .size = INT_PCI_MSI_NR, | |
| }; | |
| msi->domain = msi_create_parent_irq_domain(&info, &rcar_msi_parent_ops); | |
| if (!msi->domain) { | |
| dev_err(pcie->dev, "failed to create IRQ domain\n"); | |
| return -ENOMEM; | |
| } | |
| return 0; | |
| } | |
| static void rcar_free_domains(struct rcar_msi *msi) | |
| { | |
| irq_domain_remove(msi->domain); | |
| } | |
| static int rcar_pcie_enable_msi(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| struct device *dev = pcie->dev; | |
| struct rcar_msi *msi = &host->msi; | |
| struct resource res; | |
| int err; | |
| mutex_init(&msi->map_lock); | |
| raw_spin_lock_init(&msi->mask_lock); | |
| err = of_address_to_resource(dev->of_node, 0, &res); | |
| if (err) | |
| return err; | |
| err = rcar_allocate_domains(msi); | |
| if (err) | |
| return err; | |
| /* Two IRQs are for MSI, but they are also used for non-MSI IRQs */ | |
| err = devm_request_irq(dev, msi->irq1, rcar_pcie_msi_irq, | |
| IRQF_SHARED | IRQF_NO_THREAD, | |
| rcar_msi_bottom_chip.name, host); | |
| if (err < 0) { | |
| dev_err(dev, "failed to request IRQ: %d\n", err); | |
| goto err; | |
| } | |
| err = devm_request_irq(dev, msi->irq2, rcar_pcie_msi_irq, | |
| IRQF_SHARED | IRQF_NO_THREAD, | |
| rcar_msi_bottom_chip.name, host); | |
| if (err < 0) { | |
| dev_err(dev, "failed to request IRQ: %d\n", err); | |
| goto err; | |
| } | |
| /* Disable all MSIs */ | |
| rcar_pci_write_reg(pcie, 0, PCIEMSIIER); | |
| /* | |
| * Setup MSI data target using RC base address, which is guaranteed | |
| * to be in the low 32bit range on any R-Car HW. | |
| */ | |
| rcar_pci_write_reg(pcie, lower_32_bits(res.start) | MSIFE, PCIEMSIALR); | |
| rcar_pci_write_reg(pcie, upper_32_bits(res.start), PCIEMSIAUR); | |
| return 0; | |
| err: | |
| rcar_free_domains(msi); | |
| return err; | |
| } | |
| static void rcar_pcie_teardown_msi(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| /* Disable all MSI interrupts */ | |
| rcar_pci_write_reg(pcie, 0, PCIEMSIIER); | |
| /* Disable address decoding of the MSI interrupt, MSIFE */ | |
| rcar_pci_write_reg(pcie, 0, PCIEMSIALR); | |
| rcar_free_domains(&host->msi); | |
| } | |
| static int rcar_pcie_get_resources(struct rcar_pcie_host *host) | |
| { | |
| struct rcar_pcie *pcie = &host->pcie; | |
| struct device *dev = pcie->dev; | |
| struct resource res; | |
| int err, i; | |
| host->phy = devm_phy_optional_get(dev, "pcie"); | |
| if (IS_ERR(host->phy)) | |
| return PTR_ERR(host->phy); | |
| err = of_address_to_resource(dev->of_node, 0, &res); | |
| if (err) | |
| return err; | |
| pcie->base = devm_ioremap_resource(dev, &res); | |
| if (IS_ERR(pcie->base)) | |
| return PTR_ERR(pcie->base); | |
| host->bus_clk = devm_clk_get(dev, "pcie_bus"); | |
| if (IS_ERR(host->bus_clk)) { | |
| dev_err(dev, "cannot get pcie bus clock\n"); | |
| return PTR_ERR(host->bus_clk); | |
| } | |
| i = irq_of_parse_and_map(dev->of_node, 0); | |
| if (!i) { | |
| dev_err(dev, "cannot get platform resources for msi interrupt\n"); | |
| err = -ENOENT; | |
| goto err_irq1; | |
| } | |
| host->msi.irq1 = i; | |
| i = irq_of_parse_and_map(dev->of_node, 1); | |
| if (!i) { | |
| dev_err(dev, "cannot get platform resources for msi interrupt\n"); | |
| err = -ENOENT; | |
| goto err_irq2; | |
| } | |
| host->msi.irq2 = i; | |
| return 0; | |
| err_irq2: | |
| irq_dispose_mapping(host->msi.irq1); | |
| err_irq1: | |
| return err; | |
| } | |
| static int rcar_pcie_inbound_ranges(struct rcar_pcie *pcie, | |
| struct resource_entry *entry, | |
| int *index) | |
| { | |
| u64 restype = entry->res->flags; | |
| u64 cpu_addr = entry->res->start; | |
| u64 cpu_end = entry->res->end; | |
| u64 pci_addr = entry->res->start - entry->offset; | |
| u32 flags = LAM_64BIT | LAR_ENABLE; | |
| u64 mask; | |
| u64 size = resource_size(entry->res); | |
| int idx = *index; | |
| if (restype & IORESOURCE_PREFETCH) | |
| flags |= LAM_PREFETCH; | |
| while (cpu_addr < cpu_end) { | |
| if (idx >= MAX_NR_INBOUND_MAPS - 1) { | |
| dev_err(pcie->dev, "Failed to map inbound regions!\n"); | |
| return -EINVAL; | |
| } | |
| /* | |
| * If the size of the range is larger than the alignment of | |
| * the start address, we have to use multiple entries to | |
| * perform the mapping. | |
| */ | |
| if (cpu_addr > 0) { | |
| unsigned long nr_zeros = __ffs64(cpu_addr); | |
| u64 alignment = 1ULL << nr_zeros; | |
| size = min(size, alignment); | |
| } | |
| /* Hardware supports max 4GiB inbound region */ | |
| size = min(size, 1ULL << 32); | |
| mask = roundup_pow_of_two(size) - 1; | |
| mask &= ~0xf; | |
| rcar_pcie_set_inbound(pcie, cpu_addr, pci_addr, | |
| lower_32_bits(mask) | flags, idx, true); | |
| pci_addr += size; | |
| cpu_addr += size; | |
| idx += 2; | |
| } | |
| *index = idx; | |
| return 0; | |
| } | |
| static int rcar_pcie_parse_map_dma_ranges(struct rcar_pcie_host *host) | |
| { | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(host); | |
| struct resource_entry *entry; | |
| int index = 0, err = 0; | |
| resource_list_for_each_entry(entry, &bridge->dma_ranges) { | |
| err = rcar_pcie_inbound_ranges(&host->pcie, entry, &index); | |
| if (err) | |
| break; | |
| } | |
| return err; | |
| } | |
| static const struct of_device_id rcar_pcie_of_match[] = { | |
| { .compatible = "renesas,pcie-r8a7779", | |
| .data = rcar_pcie_phy_init_h1 }, | |
| { .compatible = "renesas,pcie-r8a7790", | |
| .data = rcar_pcie_phy_init_gen2 }, | |
| { .compatible = "renesas,pcie-r8a7791", | |
| .data = rcar_pcie_phy_init_gen2 }, | |
| { .compatible = "renesas,pcie-rcar-gen2", | |
| .data = rcar_pcie_phy_init_gen2 }, | |
| { .compatible = "renesas,pcie-r8a7795", | |
| .data = rcar_pcie_phy_init_gen3 }, | |
| { .compatible = "renesas,pcie-rcar-gen3", | |
| .data = rcar_pcie_phy_init_gen3 }, | |
| {}, | |
| }; | |
| /* Design note 346 from Linear Technology says order is not important. */ | |
| static const char * const rcar_pcie_supplies[] = { | |
| "vpcie1v5", | |
| "vpcie3v3", | |
| "vpcie12v", | |
| }; | |
| static int rcar_pcie_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| struct pci_host_bridge *bridge; | |
| struct rcar_pcie_host *host; | |
| struct rcar_pcie *pcie; | |
| unsigned int i; | |
| u32 data; | |
| int err; | |
| bridge = devm_pci_alloc_host_bridge(dev, sizeof(*host)); | |
| if (!bridge) | |
| return -ENOMEM; | |
| host = pci_host_bridge_priv(bridge); | |
| pcie = &host->pcie; | |
| pcie->dev = dev; | |
| platform_set_drvdata(pdev, host); | |
| for (i = 0; i < ARRAY_SIZE(rcar_pcie_supplies); i++) { | |
| err = devm_regulator_get_enable_optional(dev, rcar_pcie_supplies[i]); | |
| if (err < 0 && err != -ENODEV) | |
| return dev_err_probe(dev, err, "failed to enable regulator: %s\n", | |
| rcar_pcie_supplies[i]); | |
| } | |
| pm_runtime_enable(pcie->dev); | |
| err = pm_runtime_get_sync(pcie->dev); | |
| if (err < 0) { | |
| dev_err(pcie->dev, "pm_runtime_get_sync failed\n"); | |
| goto err_pm_put; | |
| } | |
| err = rcar_pcie_get_resources(host); | |
| if (err < 0) { | |
| dev_err(dev, "failed to request resources: %d\n", err); | |
| goto err_pm_put; | |
| } | |
| err = clk_prepare_enable(host->bus_clk); | |
| if (err) { | |
| dev_err(dev, "failed to enable bus clock: %d\n", err); | |
| goto err_unmap_msi_irqs; | |
| } | |
| err = rcar_pcie_parse_map_dma_ranges(host); | |
| if (err) | |
| goto err_clk_disable; | |
| host->phy_init_fn = of_device_get_match_data(dev); | |
| err = host->phy_init_fn(host); | |
| if (err) { | |
| dev_err(dev, "failed to init PCIe PHY\n"); | |
| goto err_clk_disable; | |
| } | |
| /* Failure to get a link might just be that no cards are inserted */ | |
| if (rcar_pcie_hw_init(pcie)) { | |
| dev_info(dev, "PCIe link down\n"); | |
| err = -ENODEV; | |
| goto err_phy_shutdown; | |
| } | |
| data = rcar_pci_read_reg(pcie, MACSR); | |
| dev_info(dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f); | |
| if (IS_ENABLED(CONFIG_PCI_MSI)) { | |
| err = rcar_pcie_enable_msi(host); | |
| if (err < 0) { | |
| dev_err(dev, | |
| "failed to enable MSI support: %d\n", | |
| err); | |
| goto err_phy_shutdown; | |
| } | |
| } | |
| err = rcar_pcie_enable(host); | |
| if (err) | |
| goto err_msi_teardown; | |
| return 0; | |
| err_msi_teardown: | |
| if (IS_ENABLED(CONFIG_PCI_MSI)) | |
| rcar_pcie_teardown_msi(host); | |
| err_phy_shutdown: | |
| if (host->phy) { | |
| phy_power_off(host->phy); | |
| phy_exit(host->phy); | |
| } | |
| err_clk_disable: | |
| clk_disable_unprepare(host->bus_clk); | |
| err_unmap_msi_irqs: | |
| irq_dispose_mapping(host->msi.irq2); | |
| irq_dispose_mapping(host->msi.irq1); | |
| err_pm_put: | |
| pm_runtime_put(dev); | |
| pm_runtime_disable(dev); | |
| return err; | |
| } | |
| static int rcar_pcie_resume(struct device *dev) | |
| { | |
| struct rcar_pcie_host *host = dev_get_drvdata(dev); | |
| struct rcar_pcie *pcie = &host->pcie; | |
| unsigned int data; | |
| int err; | |
| err = rcar_pcie_parse_map_dma_ranges(host); | |
| if (err) | |
| return 0; | |
| /* Failure to get a link might just be that no cards are inserted */ | |
| err = host->phy_init_fn(host); | |
| if (err) { | |
| dev_info(dev, "PCIe link down\n"); | |
| return 0; | |
| } | |
| data = rcar_pci_read_reg(pcie, MACSR); | |
| dev_info(dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f); | |
| /* Enable MSI */ | |
| if (IS_ENABLED(CONFIG_PCI_MSI)) { | |
| struct resource res; | |
| u32 val; | |
| of_address_to_resource(dev->of_node, 0, &res); | |
| rcar_pci_write_reg(pcie, upper_32_bits(res.start), PCIEMSIAUR); | |
| rcar_pci_write_reg(pcie, lower_32_bits(res.start) | MSIFE, PCIEMSIALR); | |
| bitmap_to_arr32(&val, host->msi.used, INT_PCI_MSI_NR); | |
| rcar_pci_write_reg(pcie, val, PCIEMSIIER); | |
| } | |
| rcar_pcie_hw_enable(host); | |
| return 0; | |
| } | |
| static int rcar_pcie_resume_noirq(struct device *dev) | |
| { | |
| struct rcar_pcie_host *host = dev_get_drvdata(dev); | |
| struct rcar_pcie *pcie = &host->pcie; | |
| if (rcar_pci_read_reg(pcie, PMSR) && | |
| !(rcar_pci_read_reg(pcie, PCIETCTLR) & DL_DOWN)) | |
| return 0; | |
| /* Re-establish the PCIe link */ | |
| rcar_pci_write_reg(pcie, MACCTLR_INIT_VAL, MACCTLR); | |
| rcar_pci_write_reg(pcie, CFINIT, PCIETCTLR); | |
| return rcar_pcie_wait_for_dl(pcie); | |
| } | |
| static const struct dev_pm_ops rcar_pcie_pm_ops = { | |
| SYSTEM_SLEEP_PM_OPS(NULL, rcar_pcie_resume) | |
| .resume_noirq = rcar_pcie_resume_noirq, | |
| }; | |
| static struct platform_driver rcar_pcie_driver = { | |
| .driver = { | |
| .name = "rcar-pcie", | |
| .of_match_table = rcar_pcie_of_match, | |
| .pm = &rcar_pcie_pm_ops, | |
| .suppress_bind_attrs = true, | |
| }, | |
| .probe = rcar_pcie_probe, | |
| }; | |
| #ifdef CONFIG_ARM | |
| static int rcar_pcie_aarch32_abort_handler(unsigned long addr, | |
| unsigned int fsr, struct pt_regs *regs) | |
| { | |
| return !fixup_exception(regs); | |
| } | |
| static const struct of_device_id rcar_pcie_abort_handler_of_match[] __initconst = { | |
| { .compatible = "renesas,pcie-r8a7779" }, | |
| { .compatible = "renesas,pcie-r8a7790" }, | |
| { .compatible = "renesas,pcie-r8a7791" }, | |
| { .compatible = "renesas,pcie-rcar-gen2" }, | |
| {}, | |
| }; | |
| static int __init rcar_pcie_init(void) | |
| { | |
| if (of_find_matching_node(NULL, rcar_pcie_abort_handler_of_match)) { | |
| #ifdef CONFIG_ARM_LPAE | |
| hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0, | |
| "asynchronous external abort"); | |
| #else | |
| hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0, | |
| "imprecise external abort"); | |
| #endif | |
| } | |
| return platform_driver_register(&rcar_pcie_driver); | |
| } | |
| device_initcall(rcar_pcie_init); | |
| #else | |
| builtin_platform_driver(rcar_pcie_driver); | |
| #endif |