| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Copyright (C) 2014 Hauke Mehrtens <hauke@hauke-m.de> | |
| * Copyright (C) 2015 Broadcom Corporation | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/pci.h> | |
| #include <linux/pci-ecam.h> | |
| #include <linux/msi.h> | |
| #include <linux/clk.h> | |
| #include <linux/module.h> | |
| #include <linux/mbus.h> | |
| #include <linux/slab.h> | |
| #include <linux/delay.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irqchip/arm-gic-v3.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_pci.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/phy/phy.h> | |
| #include "pcie-iproc.h" | |
| #define EP_PERST_SOURCE_SELECT_SHIFT 2 | |
| #define EP_PERST_SOURCE_SELECT BIT(EP_PERST_SOURCE_SELECT_SHIFT) | |
| #define EP_MODE_SURVIVE_PERST_SHIFT 1 | |
| #define EP_MODE_SURVIVE_PERST BIT(EP_MODE_SURVIVE_PERST_SHIFT) | |
| #define RC_PCIE_RST_OUTPUT_SHIFT 0 | |
| #define RC_PCIE_RST_OUTPUT BIT(RC_PCIE_RST_OUTPUT_SHIFT) | |
| #define PAXC_RESET_MASK 0x7f | |
| #define GIC_V3_CFG_SHIFT 0 | |
| #define GIC_V3_CFG BIT(GIC_V3_CFG_SHIFT) | |
| #define MSI_ENABLE_CFG_SHIFT 0 | |
| #define MSI_ENABLE_CFG BIT(MSI_ENABLE_CFG_SHIFT) | |
| #define CFG_IND_ADDR_MASK 0x00001ffc | |
| #define CFG_ADDR_REG_NUM_MASK 0x00000ffc | |
| #define CFG_ADDR_CFG_TYPE_1 1 | |
| #define SYS_RC_INTX_MASK 0xf | |
| #define PCIE_PHYLINKUP_SHIFT 3 | |
| #define PCIE_PHYLINKUP BIT(PCIE_PHYLINKUP_SHIFT) | |
| #define PCIE_DL_ACTIVE_SHIFT 2 | |
| #define PCIE_DL_ACTIVE BIT(PCIE_DL_ACTIVE_SHIFT) | |
| #define APB_ERR_EN_SHIFT 0 | |
| #define APB_ERR_EN BIT(APB_ERR_EN_SHIFT) | |
| #define CFG_RD_SUCCESS 0 | |
| #define CFG_RD_UR 1 | |
| #define CFG_RD_RRS 2 | |
| #define CFG_RD_CA 3 | |
| #define CFG_RETRY_STATUS 0xffff0001 | |
| #define CFG_RETRY_STATUS_TIMEOUT_US 500000 /* 500 milliseconds */ | |
| /* derive the enum index of the outbound/inbound mapping registers */ | |
| #define MAP_REG(base_reg, index) ((base_reg) + (index) * 2) | |
| /* | |
| * Maximum number of outbound mapping window sizes that can be supported by any | |
| * OARR/OMAP mapping pair | |
| */ | |
| #define MAX_NUM_OB_WINDOW_SIZES 4 | |
| #define OARR_VALID_SHIFT 0 | |
| #define OARR_VALID BIT(OARR_VALID_SHIFT) | |
| #define OARR_SIZE_CFG_SHIFT 1 | |
| /* | |
| * Maximum number of inbound mapping region sizes that can be supported by an | |
| * IARR | |
| */ | |
| #define MAX_NUM_IB_REGION_SIZES 9 | |
| #define IMAP_VALID_SHIFT 0 | |
| #define IMAP_VALID BIT(IMAP_VALID_SHIFT) | |
| #define IPROC_PCI_PM_CAP 0x48 | |
| #define IPROC_PCI_PM_CAP_MASK 0xffff | |
| #define IPROC_PCI_EXP_CAP 0xac | |
| #define IPROC_PCIE_REG_INVALID 0xffff | |
| /** | |
| * struct iproc_pcie_ob_map - iProc PCIe outbound mapping controller-specific | |
| * parameters | |
| * @window_sizes: list of supported outbound mapping window sizes in MB | |
| * @nr_sizes: number of supported outbound mapping window sizes | |
| */ | |
| struct iproc_pcie_ob_map { | |
| resource_size_t window_sizes[MAX_NUM_OB_WINDOW_SIZES]; | |
| unsigned int nr_sizes; | |
| }; | |
| static const struct iproc_pcie_ob_map paxb_ob_map[] = { | |
| { | |
| /* OARR0/OMAP0 */ | |
| .window_sizes = { 128, 256 }, | |
| .nr_sizes = 2, | |
| }, | |
| { | |
| /* OARR1/OMAP1 */ | |
| .window_sizes = { 128, 256 }, | |
| .nr_sizes = 2, | |
| }, | |
| }; | |
| static const struct iproc_pcie_ob_map paxb_v2_ob_map[] = { | |
| { | |
| /* OARR0/OMAP0 */ | |
| .window_sizes = { 128, 256 }, | |
| .nr_sizes = 2, | |
| }, | |
| { | |
| /* OARR1/OMAP1 */ | |
| .window_sizes = { 128, 256 }, | |
| .nr_sizes = 2, | |
| }, | |
| { | |
| /* OARR2/OMAP2 */ | |
| .window_sizes = { 128, 256, 512, 1024 }, | |
| .nr_sizes = 4, | |
| }, | |
| { | |
| /* OARR3/OMAP3 */ | |
| .window_sizes = { 128, 256, 512, 1024 }, | |
| .nr_sizes = 4, | |
| }, | |
| }; | |
| /** | |
| * enum iproc_pcie_ib_map_type - iProc PCIe inbound mapping type | |
| * @IPROC_PCIE_IB_MAP_MEM: DDR memory | |
| * @IPROC_PCIE_IB_MAP_IO: device I/O memory | |
| * @IPROC_PCIE_IB_MAP_INVALID: invalid or unused | |
| */ | |
| enum iproc_pcie_ib_map_type { | |
| IPROC_PCIE_IB_MAP_MEM = 0, | |
| IPROC_PCIE_IB_MAP_IO, | |
| IPROC_PCIE_IB_MAP_INVALID | |
| }; | |
| /** | |
| * struct iproc_pcie_ib_map - iProc PCIe inbound mapping controller-specific | |
| * parameters | |
| * @type: inbound mapping region type | |
| * @size_unit: inbound mapping region size unit, could be SZ_1K, SZ_1M, or | |
| * SZ_1G | |
| * @region_sizes: list of supported inbound mapping region sizes in KB, MB, or | |
| * GB, depending on the size unit | |
| * @nr_sizes: number of supported inbound mapping region sizes | |
| * @nr_windows: number of supported inbound mapping windows for the region | |
| * @imap_addr_offset: register offset between the upper and lower 32-bit | |
| * IMAP address registers | |
| * @imap_window_offset: register offset between each IMAP window | |
| */ | |
| struct iproc_pcie_ib_map { | |
| enum iproc_pcie_ib_map_type type; | |
| unsigned int size_unit; | |
| resource_size_t region_sizes[MAX_NUM_IB_REGION_SIZES]; | |
| unsigned int nr_sizes; | |
| unsigned int nr_windows; | |
| u16 imap_addr_offset; | |
| u16 imap_window_offset; | |
| }; | |
| static const struct iproc_pcie_ib_map paxb_v2_ib_map[] = { | |
| { | |
| /* IARR0/IMAP0 */ | |
| .type = IPROC_PCIE_IB_MAP_IO, | |
| .size_unit = SZ_1K, | |
| .region_sizes = { 32 }, | |
| .nr_sizes = 1, | |
| .nr_windows = 8, | |
| .imap_addr_offset = 0x40, | |
| .imap_window_offset = 0x4, | |
| }, | |
| { | |
| /* IARR1/IMAP1 */ | |
| .type = IPROC_PCIE_IB_MAP_MEM, | |
| .size_unit = SZ_1M, | |
| .region_sizes = { 8 }, | |
| .nr_sizes = 1, | |
| .nr_windows = 8, | |
| .imap_addr_offset = 0x4, | |
| .imap_window_offset = 0x8, | |
| }, | |
| { | |
| /* IARR2/IMAP2 */ | |
| .type = IPROC_PCIE_IB_MAP_MEM, | |
| .size_unit = SZ_1M, | |
| .region_sizes = { 64, 128, 256, 512, 1024, 2048, 4096, 8192, | |
| 16384 }, | |
| .nr_sizes = 9, | |
| .nr_windows = 1, | |
| .imap_addr_offset = 0x4, | |
| .imap_window_offset = 0x8, | |
| }, | |
| { | |
| /* IARR3/IMAP3 */ | |
| .type = IPROC_PCIE_IB_MAP_MEM, | |
| .size_unit = SZ_1G, | |
| .region_sizes = { 1, 2, 4, 8, 16, 32 }, | |
| .nr_sizes = 6, | |
| .nr_windows = 8, | |
| .imap_addr_offset = 0x4, | |
| .imap_window_offset = 0x8, | |
| }, | |
| { | |
| /* IARR4/IMAP4 */ | |
| .type = IPROC_PCIE_IB_MAP_MEM, | |
| .size_unit = SZ_1G, | |
| .region_sizes = { 32, 64, 128, 256, 512 }, | |
| .nr_sizes = 5, | |
| .nr_windows = 8, | |
| .imap_addr_offset = 0x4, | |
| .imap_window_offset = 0x8, | |
| }, | |
| }; | |
| /* | |
| * iProc PCIe host registers | |
| */ | |
| enum iproc_pcie_reg { | |
| /* clock/reset signal control */ | |
| IPROC_PCIE_CLK_CTRL = 0, | |
| /* | |
| * To allow MSI to be steered to an external MSI controller (e.g., ARM | |
| * GICv3 ITS) | |
| */ | |
| IPROC_PCIE_MSI_GIC_MODE, | |
| /* | |
| * IPROC_PCIE_MSI_BASE_ADDR and IPROC_PCIE_MSI_WINDOW_SIZE define the | |
| * window where the MSI posted writes are written, for the writes to be | |
| * interpreted as MSI writes. | |
| */ | |
| IPROC_PCIE_MSI_BASE_ADDR, | |
| IPROC_PCIE_MSI_WINDOW_SIZE, | |
| /* | |
| * To hold the address of the register where the MSI writes are | |
| * programmed. When ARM GICv3 ITS is used, this should be programmed | |
| * with the address of the GITS_TRANSLATER register. | |
| */ | |
| IPROC_PCIE_MSI_ADDR_LO, | |
| IPROC_PCIE_MSI_ADDR_HI, | |
| /* enable MSI */ | |
| IPROC_PCIE_MSI_EN_CFG, | |
| /* allow access to root complex configuration space */ | |
| IPROC_PCIE_CFG_IND_ADDR, | |
| IPROC_PCIE_CFG_IND_DATA, | |
| /* allow access to device configuration space */ | |
| IPROC_PCIE_CFG_ADDR, | |
| IPROC_PCIE_CFG_DATA, | |
| /* enable INTx */ | |
| IPROC_PCIE_INTX_EN, | |
| /* outbound address mapping */ | |
| IPROC_PCIE_OARR0, | |
| IPROC_PCIE_OMAP0, | |
| IPROC_PCIE_OARR1, | |
| IPROC_PCIE_OMAP1, | |
| IPROC_PCIE_OARR2, | |
| IPROC_PCIE_OMAP2, | |
| IPROC_PCIE_OARR3, | |
| IPROC_PCIE_OMAP3, | |
| /* inbound address mapping */ | |
| IPROC_PCIE_IARR0, | |
| IPROC_PCIE_IMAP0, | |
| IPROC_PCIE_IARR1, | |
| IPROC_PCIE_IMAP1, | |
| IPROC_PCIE_IARR2, | |
| IPROC_PCIE_IMAP2, | |
| IPROC_PCIE_IARR3, | |
| IPROC_PCIE_IMAP3, | |
| IPROC_PCIE_IARR4, | |
| IPROC_PCIE_IMAP4, | |
| /* config read status */ | |
| IPROC_PCIE_CFG_RD_STATUS, | |
| /* link status */ | |
| IPROC_PCIE_LINK_STATUS, | |
| /* enable APB error for unsupported requests */ | |
| IPROC_PCIE_APB_ERR_EN, | |
| /* total number of core registers */ | |
| IPROC_PCIE_MAX_NUM_REG, | |
| }; | |
| /* iProc PCIe PAXB BCMA registers */ | |
| static const u16 iproc_pcie_reg_paxb_bcma[IPROC_PCIE_MAX_NUM_REG] = { | |
| [IPROC_PCIE_CLK_CTRL] = 0x000, | |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x120, | |
| [IPROC_PCIE_CFG_IND_DATA] = 0x124, | |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, | |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, | |
| [IPROC_PCIE_INTX_EN] = 0x330, | |
| [IPROC_PCIE_LINK_STATUS] = 0xf0c, | |
| }; | |
| /* iProc PCIe PAXB registers */ | |
| static const u16 iproc_pcie_reg_paxb[IPROC_PCIE_MAX_NUM_REG] = { | |
| [IPROC_PCIE_CLK_CTRL] = 0x000, | |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x120, | |
| [IPROC_PCIE_CFG_IND_DATA] = 0x124, | |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, | |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, | |
| [IPROC_PCIE_INTX_EN] = 0x330, | |
| [IPROC_PCIE_OARR0] = 0xd20, | |
| [IPROC_PCIE_OMAP0] = 0xd40, | |
| [IPROC_PCIE_OARR1] = 0xd28, | |
| [IPROC_PCIE_OMAP1] = 0xd48, | |
| [IPROC_PCIE_LINK_STATUS] = 0xf0c, | |
| [IPROC_PCIE_APB_ERR_EN] = 0xf40, | |
| }; | |
| /* iProc PCIe PAXB v2 registers */ | |
| static const u16 iproc_pcie_reg_paxb_v2[IPROC_PCIE_MAX_NUM_REG] = { | |
| [IPROC_PCIE_CLK_CTRL] = 0x000, | |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x120, | |
| [IPROC_PCIE_CFG_IND_DATA] = 0x124, | |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, | |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, | |
| [IPROC_PCIE_INTX_EN] = 0x330, | |
| [IPROC_PCIE_OARR0] = 0xd20, | |
| [IPROC_PCIE_OMAP0] = 0xd40, | |
| [IPROC_PCIE_OARR1] = 0xd28, | |
| [IPROC_PCIE_OMAP1] = 0xd48, | |
| [IPROC_PCIE_OARR2] = 0xd60, | |
| [IPROC_PCIE_OMAP2] = 0xd68, | |
| [IPROC_PCIE_OARR3] = 0xdf0, | |
| [IPROC_PCIE_OMAP3] = 0xdf8, | |
| [IPROC_PCIE_IARR0] = 0xd00, | |
| [IPROC_PCIE_IMAP0] = 0xc00, | |
| [IPROC_PCIE_IARR1] = 0xd08, | |
| [IPROC_PCIE_IMAP1] = 0xd70, | |
| [IPROC_PCIE_IARR2] = 0xd10, | |
| [IPROC_PCIE_IMAP2] = 0xcc0, | |
| [IPROC_PCIE_IARR3] = 0xe00, | |
| [IPROC_PCIE_IMAP3] = 0xe08, | |
| [IPROC_PCIE_IARR4] = 0xe68, | |
| [IPROC_PCIE_IMAP4] = 0xe70, | |
| [IPROC_PCIE_CFG_RD_STATUS] = 0xee0, | |
| [IPROC_PCIE_LINK_STATUS] = 0xf0c, | |
| [IPROC_PCIE_APB_ERR_EN] = 0xf40, | |
| }; | |
| /* iProc PCIe PAXC v1 registers */ | |
| static const u16 iproc_pcie_reg_paxc[IPROC_PCIE_MAX_NUM_REG] = { | |
| [IPROC_PCIE_CLK_CTRL] = 0x000, | |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x1f0, | |
| [IPROC_PCIE_CFG_IND_DATA] = 0x1f4, | |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, | |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, | |
| }; | |
| /* iProc PCIe PAXC v2 registers */ | |
| static const u16 iproc_pcie_reg_paxc_v2[IPROC_PCIE_MAX_NUM_REG] = { | |
| [IPROC_PCIE_MSI_GIC_MODE] = 0x050, | |
| [IPROC_PCIE_MSI_BASE_ADDR] = 0x074, | |
| [IPROC_PCIE_MSI_WINDOW_SIZE] = 0x078, | |
| [IPROC_PCIE_MSI_ADDR_LO] = 0x07c, | |
| [IPROC_PCIE_MSI_ADDR_HI] = 0x080, | |
| [IPROC_PCIE_MSI_EN_CFG] = 0x09c, | |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x1f0, | |
| [IPROC_PCIE_CFG_IND_DATA] = 0x1f4, | |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, | |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, | |
| }; | |
| /* | |
| * List of device IDs of controllers that have corrupted capability list that | |
| * require SW fixup | |
| */ | |
| static const u16 iproc_pcie_corrupt_cap_did[] = { | |
| 0x16cd, | |
| 0x16f0, | |
| 0xd802, | |
| 0xd804 | |
| }; | |
| static inline struct iproc_pcie *iproc_data(struct pci_bus *bus) | |
| { | |
| struct iproc_pcie *pcie = bus->sysdata; | |
| return pcie; | |
| } | |
| static inline bool iproc_pcie_reg_is_invalid(u16 reg_offset) | |
| { | |
| return !!(reg_offset == IPROC_PCIE_REG_INVALID); | |
| } | |
| static inline u16 iproc_pcie_reg_offset(struct iproc_pcie *pcie, | |
| enum iproc_pcie_reg reg) | |
| { | |
| return pcie->reg_offsets[reg]; | |
| } | |
| static inline u32 iproc_pcie_read_reg(struct iproc_pcie *pcie, | |
| enum iproc_pcie_reg reg) | |
| { | |
| u16 offset = iproc_pcie_reg_offset(pcie, reg); | |
| if (iproc_pcie_reg_is_invalid(offset)) | |
| return 0; | |
| return readl(pcie->base + offset); | |
| } | |
| static inline void iproc_pcie_write_reg(struct iproc_pcie *pcie, | |
| enum iproc_pcie_reg reg, u32 val) | |
| { | |
| u16 offset = iproc_pcie_reg_offset(pcie, reg); | |
| if (iproc_pcie_reg_is_invalid(offset)) | |
| return; | |
| writel(val, pcie->base + offset); | |
| } | |
| /* | |
| * APB error forwarding can be disabled during access of configuration | |
| * registers of the endpoint device, to prevent unsupported requests | |
| * (typically seen during enumeration with multi-function devices) from | |
| * triggering a system exception. | |
| */ | |
| static inline void iproc_pcie_apb_err_disable(struct pci_bus *bus, | |
| bool disable) | |
| { | |
| struct iproc_pcie *pcie = iproc_data(bus); | |
| u32 val; | |
| if (bus->number && pcie->has_apb_err_disable) { | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_APB_ERR_EN); | |
| if (disable) | |
| val &= ~APB_ERR_EN; | |
| else | |
| val |= APB_ERR_EN; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_APB_ERR_EN, val); | |
| } | |
| } | |
| static void __iomem *iproc_pcie_map_ep_cfg_reg(struct iproc_pcie *pcie, | |
| unsigned int busno, | |
| unsigned int devfn, | |
| int where) | |
| { | |
| u16 offset; | |
| u32 val; | |
| /* EP device access */ | |
| val = ALIGN_DOWN(PCIE_ECAM_OFFSET(busno, devfn, where), 4) | | |
| CFG_ADDR_CFG_TYPE_1; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CFG_ADDR, val); | |
| offset = iproc_pcie_reg_offset(pcie, IPROC_PCIE_CFG_DATA); | |
| if (iproc_pcie_reg_is_invalid(offset)) | |
| return NULL; | |
| return (pcie->base + offset); | |
| } | |
| static unsigned int iproc_pcie_cfg_retry(struct iproc_pcie *pcie, | |
| void __iomem *cfg_data_p) | |
| { | |
| int timeout = CFG_RETRY_STATUS_TIMEOUT_US; | |
| unsigned int data; | |
| u32 status; | |
| /* | |
| * As per PCIe r6.0, sec 2.3.2, Config RRS Software Visibility only | |
| * affects config reads of the Vendor ID. For config writes or any | |
| * other config reads, the Root may automatically reissue the | |
| * configuration request again as a new request. | |
| * | |
| * For config reads, this hardware returns CFG_RETRY_STATUS data | |
| * when it receives a RRS completion, regardless of the address of | |
| * the read or the RRS Software Visibility Enable bit. As a | |
| * partial workaround for this, we retry in software any read that | |
| * returns CFG_RETRY_STATUS. | |
| * | |
| * Note that a non-Vendor ID config register may have a value of | |
| * CFG_RETRY_STATUS. If we read that, we can't distinguish it from | |
| * a RRS completion, so we will incorrectly retry the read and | |
| * eventually return the wrong data (0xffffffff). | |
| */ | |
| data = readl(cfg_data_p); | |
| while (data == CFG_RETRY_STATUS && timeout--) { | |
| /* | |
| * RRS state is set in CFG_RD status register | |
| * This will handle the case where CFG_RETRY_STATUS is | |
| * valid config data. | |
| */ | |
| status = iproc_pcie_read_reg(pcie, IPROC_PCIE_CFG_RD_STATUS); | |
| if (status != CFG_RD_RRS) | |
| return data; | |
| udelay(1); | |
| data = readl(cfg_data_p); | |
| } | |
| if (data == CFG_RETRY_STATUS) | |
| data = 0xffffffff; | |
| return data; | |
| } | |
| static void iproc_pcie_fix_cap(struct iproc_pcie *pcie, int where, u32 *val) | |
| { | |
| u32 i, dev_id; | |
| switch (where & ~0x3) { | |
| case PCI_VENDOR_ID: | |
| dev_id = *val >> 16; | |
| /* | |
| * Activate fixup for those controllers that have corrupted | |
| * capability list registers | |
| */ | |
| for (i = 0; i < ARRAY_SIZE(iproc_pcie_corrupt_cap_did); i++) | |
| if (dev_id == iproc_pcie_corrupt_cap_did[i]) | |
| pcie->fix_paxc_cap = true; | |
| break; | |
| case IPROC_PCI_PM_CAP: | |
| if (pcie->fix_paxc_cap) { | |
| /* advertise PM, force next capability to PCIe */ | |
| *val &= ~IPROC_PCI_PM_CAP_MASK; | |
| *val |= IPROC_PCI_EXP_CAP << 8 | PCI_CAP_ID_PM; | |
| } | |
| break; | |
| case IPROC_PCI_EXP_CAP: | |
| if (pcie->fix_paxc_cap) { | |
| /* advertise root port, version 2, terminate here */ | |
| *val = (PCI_EXP_TYPE_ROOT_PORT << 4 | 2) << 16 | | |
| PCI_CAP_ID_EXP; | |
| } | |
| break; | |
| case IPROC_PCI_EXP_CAP + PCI_EXP_RTCTL: | |
| /* Don't advertise RRS SV support */ | |
| *val &= ~(PCI_EXP_RTCAP_RRS_SV << 16); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static int iproc_pcie_config_read(struct pci_bus *bus, unsigned int devfn, | |
| int where, int size, u32 *val) | |
| { | |
| struct iproc_pcie *pcie = iproc_data(bus); | |
| unsigned int busno = bus->number; | |
| void __iomem *cfg_data_p; | |
| unsigned int data; | |
| int ret; | |
| /* root complex access */ | |
| if (busno == 0) { | |
| ret = pci_generic_config_read32(bus, devfn, where, size, val); | |
| if (ret == PCIBIOS_SUCCESSFUL) | |
| iproc_pcie_fix_cap(pcie, where, val); | |
| return ret; | |
| } | |
| cfg_data_p = iproc_pcie_map_ep_cfg_reg(pcie, busno, devfn, where); | |
| if (!cfg_data_p) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| data = iproc_pcie_cfg_retry(pcie, cfg_data_p); | |
| *val = data; | |
| if (size <= 2) | |
| *val = (data >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); | |
| /* | |
| * For PAXC and PAXCv2, the total number of PFs that one can enumerate | |
| * depends on the firmware configuration. Unfortunately, due to an ASIC | |
| * bug, unconfigured PFs cannot be properly hidden from the root | |
| * complex. As a result, write access to these PFs will cause bus lock | |
| * up on the embedded processor | |
| * | |
| * Since all unconfigured PFs are left with an incorrect, staled device | |
| * ID of 0x168e (PCI_DEVICE_ID_NX2_57810), we try to catch those access | |
| * early here and reject them all | |
| */ | |
| #define DEVICE_ID_MASK 0xffff0000 | |
| #define DEVICE_ID_SHIFT 16 | |
| if (pcie->rej_unconfig_pf && | |
| (where & CFG_ADDR_REG_NUM_MASK) == PCI_VENDOR_ID) | |
| if ((*val & DEVICE_ID_MASK) == | |
| (PCI_DEVICE_ID_NX2_57810 << DEVICE_ID_SHIFT)) | |
| return PCIBIOS_FUNC_NOT_SUPPORTED; | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| /* | |
| * Note access to the configuration registers are protected at the higher layer | |
| * by 'pci_lock' in drivers/pci/access.c | |
| */ | |
| static void __iomem *iproc_pcie_map_cfg_bus(struct iproc_pcie *pcie, | |
| int busno, unsigned int devfn, | |
| int where) | |
| { | |
| u16 offset; | |
| /* root complex access */ | |
| if (busno == 0) { | |
| if (PCIE_ECAM_DEVFN(devfn) > 0) | |
| return NULL; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CFG_IND_ADDR, | |
| where & CFG_IND_ADDR_MASK); | |
| offset = iproc_pcie_reg_offset(pcie, IPROC_PCIE_CFG_IND_DATA); | |
| if (iproc_pcie_reg_is_invalid(offset)) | |
| return NULL; | |
| else | |
| return (pcie->base + offset); | |
| } | |
| return iproc_pcie_map_ep_cfg_reg(pcie, busno, devfn, where); | |
| } | |
| static void __iomem *iproc_pcie_bus_map_cfg_bus(struct pci_bus *bus, | |
| unsigned int devfn, | |
| int where) | |
| { | |
| return iproc_pcie_map_cfg_bus(iproc_data(bus), bus->number, devfn, | |
| where); | |
| } | |
| static int iproc_pci_raw_config_read32(struct iproc_pcie *pcie, | |
| unsigned int devfn, int where, | |
| int size, u32 *val) | |
| { | |
| void __iomem *addr; | |
| addr = iproc_pcie_map_cfg_bus(pcie, 0, devfn, where & ~0x3); | |
| if (!addr) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| *val = readl(addr); | |
| if (size <= 2) | |
| *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| static int iproc_pci_raw_config_write32(struct iproc_pcie *pcie, | |
| unsigned int devfn, int where, | |
| int size, u32 val) | |
| { | |
| void __iomem *addr; | |
| u32 mask, tmp; | |
| addr = iproc_pcie_map_cfg_bus(pcie, 0, devfn, where & ~0x3); | |
| if (!addr) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| if (size == 4) { | |
| writel(val, addr); | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| mask = ~(((1 << (size * 8)) - 1) << ((where & 0x3) * 8)); | |
| tmp = readl(addr) & mask; | |
| tmp |= val << ((where & 0x3) * 8); | |
| writel(tmp, addr); | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| static int iproc_pcie_config_read32(struct pci_bus *bus, unsigned int devfn, | |
| int where, int size, u32 *val) | |
| { | |
| int ret; | |
| struct iproc_pcie *pcie = iproc_data(bus); | |
| iproc_pcie_apb_err_disable(bus, true); | |
| if (pcie->iproc_cfg_read) | |
| ret = iproc_pcie_config_read(bus, devfn, where, size, val); | |
| else | |
| ret = pci_generic_config_read32(bus, devfn, where, size, val); | |
| iproc_pcie_apb_err_disable(bus, false); | |
| return ret; | |
| } | |
| static int iproc_pcie_config_write32(struct pci_bus *bus, unsigned int devfn, | |
| int where, int size, u32 val) | |
| { | |
| int ret; | |
| iproc_pcie_apb_err_disable(bus, true); | |
| ret = pci_generic_config_write32(bus, devfn, where, size, val); | |
| iproc_pcie_apb_err_disable(bus, false); | |
| return ret; | |
| } | |
| static struct pci_ops iproc_pcie_ops = { | |
| .map_bus = iproc_pcie_bus_map_cfg_bus, | |
| .read = iproc_pcie_config_read32, | |
| .write = iproc_pcie_config_write32, | |
| }; | |
| static void iproc_pcie_perst_ctrl(struct iproc_pcie *pcie, bool assert) | |
| { | |
| u32 val; | |
| /* | |
| * PAXC and the internal emulated endpoint device downstream should not | |
| * be reset. If firmware has been loaded on the endpoint device at an | |
| * earlier boot stage, reset here causes issues. | |
| */ | |
| if (pcie->ep_is_internal) | |
| return; | |
| if (assert) { | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_CLK_CTRL); | |
| val &= ~EP_PERST_SOURCE_SELECT & ~EP_MODE_SURVIVE_PERST & | |
| ~RC_PCIE_RST_OUTPUT; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CLK_CTRL, val); | |
| udelay(250); | |
| } else { | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_CLK_CTRL); | |
| val |= RC_PCIE_RST_OUTPUT; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CLK_CTRL, val); | |
| msleep(100); | |
| } | |
| } | |
| int iproc_pcie_shutdown(struct iproc_pcie *pcie) | |
| { | |
| iproc_pcie_perst_ctrl(pcie, true); | |
| msleep(500); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL_GPL(iproc_pcie_shutdown); | |
| static int iproc_pcie_check_link(struct iproc_pcie *pcie) | |
| { | |
| struct device *dev = pcie->dev; | |
| u32 hdr_type, link_ctrl, link_status, class, val; | |
| bool link_is_active = false; | |
| /* | |
| * PAXC connects to emulated endpoint devices directly and does not | |
| * have a Serdes. Therefore skip the link detection logic here. | |
| */ | |
| if (pcie->ep_is_internal) | |
| return 0; | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_LINK_STATUS); | |
| if (!(val & PCIE_PHYLINKUP) || !(val & PCIE_DL_ACTIVE)) { | |
| dev_err(dev, "PHY or data link is INACTIVE!\n"); | |
| return -ENODEV; | |
| } | |
| /* make sure we are not in EP mode */ | |
| iproc_pci_raw_config_read32(pcie, 0, PCI_HEADER_TYPE, 1, &hdr_type); | |
| if ((hdr_type & PCI_HEADER_TYPE_MASK) != PCI_HEADER_TYPE_BRIDGE) { | |
| dev_err(dev, "in EP mode, hdr=%#02x\n", hdr_type); | |
| return -EFAULT; | |
| } | |
| /* force class to PCI_CLASS_BRIDGE_PCI_NORMAL (0x060400) */ | |
| #define PCI_BRIDGE_CTRL_REG_OFFSET 0x43c | |
| #define PCI_BRIDGE_CTRL_REG_CLASS_MASK 0xffffff | |
| iproc_pci_raw_config_read32(pcie, 0, PCI_BRIDGE_CTRL_REG_OFFSET, | |
| 4, &class); | |
| class &= ~PCI_BRIDGE_CTRL_REG_CLASS_MASK; | |
| class |= PCI_CLASS_BRIDGE_PCI_NORMAL; | |
| iproc_pci_raw_config_write32(pcie, 0, PCI_BRIDGE_CTRL_REG_OFFSET, | |
| 4, class); | |
| /* check link status to see if link is active */ | |
| iproc_pci_raw_config_read32(pcie, 0, IPROC_PCI_EXP_CAP + PCI_EXP_LNKSTA, | |
| 2, &link_status); | |
| if (link_status & PCI_EXP_LNKSTA_NLW) | |
| link_is_active = true; | |
| if (!link_is_active) { | |
| /* try GEN 1 link speed */ | |
| #define PCI_TARGET_LINK_SPEED_MASK 0xf | |
| #define PCI_TARGET_LINK_SPEED_GEN2 0x2 | |
| #define PCI_TARGET_LINK_SPEED_GEN1 0x1 | |
| iproc_pci_raw_config_read32(pcie, 0, | |
| IPROC_PCI_EXP_CAP + PCI_EXP_LNKCTL2, | |
| 4, &link_ctrl); | |
| if ((link_ctrl & PCI_TARGET_LINK_SPEED_MASK) == | |
| PCI_TARGET_LINK_SPEED_GEN2) { | |
| link_ctrl &= ~PCI_TARGET_LINK_SPEED_MASK; | |
| link_ctrl |= PCI_TARGET_LINK_SPEED_GEN1; | |
| iproc_pci_raw_config_write32(pcie, 0, | |
| IPROC_PCI_EXP_CAP + PCI_EXP_LNKCTL2, | |
| 4, link_ctrl); | |
| msleep(100); | |
| iproc_pci_raw_config_read32(pcie, 0, | |
| IPROC_PCI_EXP_CAP + PCI_EXP_LNKSTA, | |
| 2, &link_status); | |
| if (link_status & PCI_EXP_LNKSTA_NLW) | |
| link_is_active = true; | |
| } | |
| } | |
| dev_info(dev, "link: %s\n", link_is_active ? "UP" : "DOWN"); | |
| return link_is_active ? 0 : -ENODEV; | |
| } | |
| static void iproc_pcie_enable(struct iproc_pcie *pcie) | |
| { | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, SYS_RC_INTX_MASK); | |
| } | |
| static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie, | |
| int window_idx) | |
| { | |
| u32 val; | |
| val = iproc_pcie_read_reg(pcie, MAP_REG(IPROC_PCIE_OARR0, window_idx)); | |
| return !!(val & OARR_VALID); | |
| } | |
| static inline int iproc_pcie_ob_write(struct iproc_pcie *pcie, int window_idx, | |
| int size_idx, u64 axi_addr, u64 pci_addr) | |
| { | |
| struct device *dev = pcie->dev; | |
| u16 oarr_offset, omap_offset; | |
| /* | |
| * Derive the OARR/OMAP offset from the first pair (OARR0/OMAP0) based | |
| * on window index. | |
| */ | |
| oarr_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_OARR0, | |
| window_idx)); | |
| omap_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_OMAP0, | |
| window_idx)); | |
| if (iproc_pcie_reg_is_invalid(oarr_offset) || | |
| iproc_pcie_reg_is_invalid(omap_offset)) | |
| return -EINVAL; | |
| /* | |
| * Program the OARR registers. The upper 32-bit OARR register is | |
| * always right after the lower 32-bit OARR register. | |
| */ | |
| writel(lower_32_bits(axi_addr) | (size_idx << OARR_SIZE_CFG_SHIFT) | | |
| OARR_VALID, pcie->base + oarr_offset); | |
| writel(upper_32_bits(axi_addr), pcie->base + oarr_offset + 4); | |
| /* now program the OMAP registers */ | |
| writel(lower_32_bits(pci_addr), pcie->base + omap_offset); | |
| writel(upper_32_bits(pci_addr), pcie->base + omap_offset + 4); | |
| dev_dbg(dev, "ob window [%d]: offset 0x%x axi %pap pci %pap\n", | |
| window_idx, oarr_offset, &axi_addr, &pci_addr); | |
| dev_dbg(dev, "oarr lo 0x%x oarr hi 0x%x\n", | |
| readl(pcie->base + oarr_offset), | |
| readl(pcie->base + oarr_offset + 4)); | |
| dev_dbg(dev, "omap lo 0x%x omap hi 0x%x\n", | |
| readl(pcie->base + omap_offset), | |
| readl(pcie->base + omap_offset + 4)); | |
| return 0; | |
| } | |
| /* | |
| * Some iProc SoCs require the SW to configure the outbound address mapping | |
| * | |
| * Outbound address translation: | |
| * | |
| * iproc_pcie_address = axi_address - axi_offset | |
| * OARR = iproc_pcie_address | |
| * OMAP = pci_addr | |
| * | |
| * axi_addr -> iproc_pcie_address -> OARR -> OMAP -> pci_address | |
| */ | |
| static int iproc_pcie_setup_ob(struct iproc_pcie *pcie, u64 axi_addr, | |
| u64 pci_addr, resource_size_t size) | |
| { | |
| struct iproc_pcie_ob *ob = &pcie->ob; | |
| struct device *dev = pcie->dev; | |
| int ret = -EINVAL, window_idx, size_idx; | |
| if (axi_addr < ob->axi_offset) { | |
| dev_err(dev, "axi address %pap less than offset %pap\n", | |
| &axi_addr, &ob->axi_offset); | |
| return -EINVAL; | |
| } | |
| /* | |
| * Translate the AXI address to the internal address used by the iProc | |
| * PCIe core before programming the OARR | |
| */ | |
| axi_addr -= ob->axi_offset; | |
| /* iterate through all OARR/OMAP mapping windows */ | |
| for (window_idx = ob->nr_windows - 1; window_idx >= 0; window_idx--) { | |
| const struct iproc_pcie_ob_map *ob_map = | |
| &pcie->ob_map[window_idx]; | |
| /* | |
| * If current outbound window is already in use, move on to the | |
| * next one. | |
| */ | |
| if (iproc_pcie_ob_is_valid(pcie, window_idx)) | |
| continue; | |
| /* | |
| * Iterate through all supported window sizes within the | |
| * OARR/OMAP pair to find a match. Go through the window sizes | |
| * in a descending order. | |
| */ | |
| for (size_idx = ob_map->nr_sizes - 1; size_idx >= 0; | |
| size_idx--) { | |
| resource_size_t window_size = | |
| ob_map->window_sizes[size_idx] * SZ_1M; | |
| /* | |
| * Keep iterating until we reach the last window and | |
| * with the minimal window size at index zero. In this | |
| * case, we take a compromise by mapping it using the | |
| * minimum window size that can be supported | |
| */ | |
| if (size < window_size) { | |
| if (size_idx > 0 || window_idx > 0) | |
| continue; | |
| /* | |
| * For the corner case of reaching the minimal | |
| * window size that can be supported on the | |
| * last window | |
| */ | |
| axi_addr = ALIGN_DOWN(axi_addr, window_size); | |
| pci_addr = ALIGN_DOWN(pci_addr, window_size); | |
| size = window_size; | |
| } | |
| if (!IS_ALIGNED(axi_addr, window_size) || | |
| !IS_ALIGNED(pci_addr, window_size)) { | |
| dev_err(dev, | |
| "axi %pap or pci %pap not aligned\n", | |
| &axi_addr, &pci_addr); | |
| return -EINVAL; | |
| } | |
| /* | |
| * Match found! Program both OARR and OMAP and mark | |
| * them as a valid entry. | |
| */ | |
| ret = iproc_pcie_ob_write(pcie, window_idx, size_idx, | |
| axi_addr, pci_addr); | |
| if (ret) | |
| goto err_ob; | |
| size -= window_size; | |
| if (size == 0) | |
| return 0; | |
| /* | |
| * If we are here, we are done with the current window, | |
| * but not yet finished all mappings. Need to move on | |
| * to the next window. | |
| */ | |
| axi_addr += window_size; | |
| pci_addr += window_size; | |
| break; | |
| } | |
| } | |
| err_ob: | |
| dev_err(dev, "unable to configure outbound mapping\n"); | |
| dev_err(dev, | |
| "axi %pap, axi offset %pap, pci %pap, res size %pap\n", | |
| &axi_addr, &ob->axi_offset, &pci_addr, &size); | |
| return ret; | |
| } | |
| static int iproc_pcie_map_ranges(struct iproc_pcie *pcie, | |
| struct list_head *resources) | |
| { | |
| struct device *dev = pcie->dev; | |
| struct resource_entry *window; | |
| int ret; | |
| resource_list_for_each_entry(window, resources) { | |
| struct resource *res = window->res; | |
| u64 res_type = resource_type(res); | |
| switch (res_type) { | |
| case IORESOURCE_IO: | |
| case IORESOURCE_BUS: | |
| break; | |
| case IORESOURCE_MEM: | |
| ret = iproc_pcie_setup_ob(pcie, res->start, | |
| res->start - window->offset, | |
| resource_size(res)); | |
| if (ret) | |
| return ret; | |
| break; | |
| default: | |
| dev_err(dev, "invalid resource %pR\n", res); | |
| return -EINVAL; | |
| } | |
| } | |
| return 0; | |
| } | |
| static inline bool iproc_pcie_ib_is_in_use(struct iproc_pcie *pcie, | |
| int region_idx) | |
| { | |
| const struct iproc_pcie_ib_map *ib_map = &pcie->ib_map[region_idx]; | |
| u32 val; | |
| val = iproc_pcie_read_reg(pcie, MAP_REG(IPROC_PCIE_IARR0, region_idx)); | |
| return !!(val & (BIT(ib_map->nr_sizes) - 1)); | |
| } | |
| static inline bool iproc_pcie_ib_check_type(const struct iproc_pcie_ib_map *ib_map, | |
| enum iproc_pcie_ib_map_type type) | |
| { | |
| return !!(ib_map->type == type); | |
| } | |
| static int iproc_pcie_ib_write(struct iproc_pcie *pcie, int region_idx, | |
| int size_idx, int nr_windows, u64 axi_addr, | |
| u64 pci_addr, resource_size_t size) | |
| { | |
| struct device *dev = pcie->dev; | |
| const struct iproc_pcie_ib_map *ib_map = &pcie->ib_map[region_idx]; | |
| u16 iarr_offset, imap_offset; | |
| u32 val; | |
| int window_idx; | |
| iarr_offset = iproc_pcie_reg_offset(pcie, | |
| MAP_REG(IPROC_PCIE_IARR0, region_idx)); | |
| imap_offset = iproc_pcie_reg_offset(pcie, | |
| MAP_REG(IPROC_PCIE_IMAP0, region_idx)); | |
| if (iproc_pcie_reg_is_invalid(iarr_offset) || | |
| iproc_pcie_reg_is_invalid(imap_offset)) | |
| return -EINVAL; | |
| dev_dbg(dev, "ib region [%d]: offset 0x%x axi %pap pci %pap\n", | |
| region_idx, iarr_offset, &axi_addr, &pci_addr); | |
| /* | |
| * Program the IARR registers. The upper 32-bit IARR register is | |
| * always right after the lower 32-bit IARR register. | |
| */ | |
| writel(lower_32_bits(pci_addr) | BIT(size_idx), | |
| pcie->base + iarr_offset); | |
| writel(upper_32_bits(pci_addr), pcie->base + iarr_offset + 4); | |
| dev_dbg(dev, "iarr lo 0x%x iarr hi 0x%x\n", | |
| readl(pcie->base + iarr_offset), | |
| readl(pcie->base + iarr_offset + 4)); | |
| /* | |
| * Now program the IMAP registers. Each IARR region may have one or | |
| * more IMAP windows. | |
| */ | |
| size >>= ilog2(nr_windows); | |
| for (window_idx = 0; window_idx < nr_windows; window_idx++) { | |
| val = readl(pcie->base + imap_offset); | |
| val |= lower_32_bits(axi_addr) | IMAP_VALID; | |
| writel(val, pcie->base + imap_offset); | |
| writel(upper_32_bits(axi_addr), | |
| pcie->base + imap_offset + ib_map->imap_addr_offset); | |
| dev_dbg(dev, "imap window [%d] lo 0x%x hi 0x%x\n", | |
| window_idx, readl(pcie->base + imap_offset), | |
| readl(pcie->base + imap_offset + | |
| ib_map->imap_addr_offset)); | |
| imap_offset += ib_map->imap_window_offset; | |
| axi_addr += size; | |
| } | |
| return 0; | |
| } | |
| static int iproc_pcie_setup_ib(struct iproc_pcie *pcie, | |
| struct resource_entry *entry, | |
| enum iproc_pcie_ib_map_type type) | |
| { | |
| struct device *dev = pcie->dev; | |
| struct iproc_pcie_ib *ib = &pcie->ib; | |
| int ret; | |
| unsigned int region_idx, size_idx; | |
| u64 axi_addr = entry->res->start; | |
| u64 pci_addr = entry->res->start - entry->offset; | |
| resource_size_t size = resource_size(entry->res); | |
| /* iterate through all IARR mapping regions */ | |
| for (region_idx = 0; region_idx < ib->nr_regions; region_idx++) { | |
| const struct iproc_pcie_ib_map *ib_map = | |
| &pcie->ib_map[region_idx]; | |
| /* | |
| * If current inbound region is already in use or not a | |
| * compatible type, move on to the next. | |
| */ | |
| if (iproc_pcie_ib_is_in_use(pcie, region_idx) || | |
| !iproc_pcie_ib_check_type(ib_map, type)) | |
| continue; | |
| /* iterate through all supported region sizes to find a match */ | |
| for (size_idx = 0; size_idx < ib_map->nr_sizes; size_idx++) { | |
| resource_size_t region_size = | |
| ib_map->region_sizes[size_idx] * ib_map->size_unit; | |
| if (size != region_size) | |
| continue; | |
| if (!IS_ALIGNED(axi_addr, region_size) || | |
| !IS_ALIGNED(pci_addr, region_size)) { | |
| dev_err(dev, | |
| "axi %pap or pci %pap not aligned\n", | |
| &axi_addr, &pci_addr); | |
| return -EINVAL; | |
| } | |
| /* Match found! Program IARR and all IMAP windows. */ | |
| ret = iproc_pcie_ib_write(pcie, region_idx, size_idx, | |
| ib_map->nr_windows, axi_addr, | |
| pci_addr, size); | |
| if (ret) | |
| goto err_ib; | |
| else | |
| return 0; | |
| } | |
| } | |
| ret = -EINVAL; | |
| err_ib: | |
| dev_err(dev, "unable to configure inbound mapping\n"); | |
| dev_err(dev, "axi %pap, pci %pap, res size %pap\n", | |
| &axi_addr, &pci_addr, &size); | |
| return ret; | |
| } | |
| static int iproc_pcie_map_dma_ranges(struct iproc_pcie *pcie) | |
| { | |
| struct pci_host_bridge *host = pci_host_bridge_from_priv(pcie); | |
| struct resource_entry *entry; | |
| int ret = 0; | |
| resource_list_for_each_entry(entry, &host->dma_ranges) { | |
| /* Each range entry corresponds to an inbound mapping region */ | |
| ret = iproc_pcie_setup_ib(pcie, entry, IPROC_PCIE_IB_MAP_MEM); | |
| if (ret) | |
| break; | |
| } | |
| return ret; | |
| } | |
| static void iproc_pcie_invalidate_mapping(struct iproc_pcie *pcie) | |
| { | |
| struct iproc_pcie_ib *ib = &pcie->ib; | |
| struct iproc_pcie_ob *ob = &pcie->ob; | |
| int idx; | |
| if (pcie->ep_is_internal) | |
| return; | |
| if (pcie->need_ob_cfg) { | |
| /* iterate through all OARR mapping regions */ | |
| for (idx = ob->nr_windows - 1; idx >= 0; idx--) { | |
| iproc_pcie_write_reg(pcie, | |
| MAP_REG(IPROC_PCIE_OARR0, idx), 0); | |
| } | |
| } | |
| if (pcie->need_ib_cfg) { | |
| /* iterate through all IARR mapping regions */ | |
| for (idx = 0; idx < ib->nr_regions; idx++) { | |
| iproc_pcie_write_reg(pcie, | |
| MAP_REG(IPROC_PCIE_IARR0, idx), 0); | |
| } | |
| } | |
| } | |
| static int iproce_pcie_get_msi(struct iproc_pcie *pcie, | |
| struct device_node *msi_node, | |
| u64 *msi_addr) | |
| { | |
| struct device *dev = pcie->dev; | |
| int ret; | |
| struct resource res; | |
| /* | |
| * Check if 'msi-map' points to ARM GICv3 ITS, which is the only | |
| * supported external MSI controller that requires steering. | |
| */ | |
| if (!of_device_is_compatible(msi_node, "arm,gic-v3-its")) { | |
| dev_err(dev, "unable to find compatible MSI controller\n"); | |
| return -ENODEV; | |
| } | |
| /* derive GITS_TRANSLATER address from GICv3 */ | |
| ret = of_address_to_resource(msi_node, 0, &res); | |
| if (ret < 0) { | |
| dev_err(dev, "unable to obtain MSI controller resources\n"); | |
| return ret; | |
| } | |
| *msi_addr = res.start + GITS_TRANSLATER; | |
| return 0; | |
| } | |
| static int iproc_pcie_paxb_v2_msi_steer(struct iproc_pcie *pcie, u64 msi_addr) | |
| { | |
| int ret; | |
| struct resource_entry entry; | |
| memset(&entry, 0, sizeof(entry)); | |
| entry.res = &entry.__res; | |
| msi_addr &= ~(SZ_32K - 1); | |
| entry.res->start = msi_addr; | |
| entry.res->end = msi_addr + SZ_32K - 1; | |
| ret = iproc_pcie_setup_ib(pcie, &entry, IPROC_PCIE_IB_MAP_IO); | |
| return ret; | |
| } | |
| static void iproc_pcie_paxc_v2_msi_steer(struct iproc_pcie *pcie, u64 msi_addr, | |
| bool enable) | |
| { | |
| u32 val; | |
| if (!enable) { | |
| /* | |
| * Disable PAXC MSI steering. All write transfers will be | |
| * treated as non-MSI transfers | |
| */ | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_MSI_EN_CFG); | |
| val &= ~MSI_ENABLE_CFG; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_EN_CFG, val); | |
| return; | |
| } | |
| /* | |
| * Program bits [43:13] of address of GITS_TRANSLATER register into | |
| * bits [30:0] of the MSI base address register. In fact, in all iProc | |
| * based SoCs, all I/O register bases are well below the 32-bit | |
| * boundary, so we can safely assume bits [43:32] are always zeros. | |
| */ | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_BASE_ADDR, | |
| (u32)(msi_addr >> 13)); | |
| /* use a default 8K window size */ | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_WINDOW_SIZE, 0); | |
| /* steering MSI to GICv3 ITS */ | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_MSI_GIC_MODE); | |
| val |= GIC_V3_CFG; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_GIC_MODE, val); | |
| /* | |
| * Program bits [43:2] of address of GITS_TRANSLATER register into the | |
| * iProc MSI address registers. | |
| */ | |
| msi_addr >>= 2; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_ADDR_HI, | |
| upper_32_bits(msi_addr)); | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_ADDR_LO, | |
| lower_32_bits(msi_addr)); | |
| /* enable MSI */ | |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_MSI_EN_CFG); | |
| val |= MSI_ENABLE_CFG; | |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_MSI_EN_CFG, val); | |
| } | |
| static int iproc_pcie_msi_steer(struct iproc_pcie *pcie, | |
| struct device_node *msi_node) | |
| { | |
| struct device *dev = pcie->dev; | |
| int ret; | |
| u64 msi_addr; | |
| ret = iproce_pcie_get_msi(pcie, msi_node, &msi_addr); | |
| if (ret < 0) { | |
| dev_err(dev, "msi steering failed\n"); | |
| return ret; | |
| } | |
| switch (pcie->type) { | |
| case IPROC_PCIE_PAXB_V2: | |
| ret = iproc_pcie_paxb_v2_msi_steer(pcie, msi_addr); | |
| if (ret) | |
| return ret; | |
| break; | |
| case IPROC_PCIE_PAXC_V2: | |
| iproc_pcie_paxc_v2_msi_steer(pcie, msi_addr, true); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static int iproc_pcie_msi_enable(struct iproc_pcie *pcie) | |
| { | |
| struct device_node *msi_node = NULL; | |
| int ret; | |
| /* | |
| * Either the "msi-parent" or the "msi-map" phandle needs to exist | |
| * for us to obtain the MSI node. | |
| */ | |
| of_msi_xlate(pcie->dev, &msi_node, 0); | |
| if (!msi_node) | |
| return -ENODEV; | |
| /* | |
| * Certain revisions of the iProc PCIe controller require additional | |
| * configurations to steer the MSI writes towards an external MSI | |
| * controller. | |
| */ | |
| if (pcie->need_msi_steer) { | |
| ret = iproc_pcie_msi_steer(pcie, msi_node); | |
| if (ret) | |
| goto out_put_node; | |
| } | |
| /* | |
| * If another MSI controller is being used, the call below should fail | |
| * but that is okay | |
| */ | |
| ret = iproc_msi_init(pcie, msi_node); | |
| out_put_node: | |
| of_node_put(msi_node); | |
| return ret; | |
| } | |
| static void iproc_pcie_msi_disable(struct iproc_pcie *pcie) | |
| { | |
| iproc_msi_exit(pcie); | |
| } | |
| static int iproc_pcie_rev_init(struct iproc_pcie *pcie) | |
| { | |
| struct device *dev = pcie->dev; | |
| unsigned int reg_idx; | |
| const u16 *regs; | |
| switch (pcie->type) { | |
| case IPROC_PCIE_PAXB_BCMA: | |
| regs = iproc_pcie_reg_paxb_bcma; | |
| break; | |
| case IPROC_PCIE_PAXB: | |
| regs = iproc_pcie_reg_paxb; | |
| pcie->has_apb_err_disable = true; | |
| if (pcie->need_ob_cfg) { | |
| pcie->ob_map = paxb_ob_map; | |
| pcie->ob.nr_windows = ARRAY_SIZE(paxb_ob_map); | |
| } | |
| break; | |
| case IPROC_PCIE_PAXB_V2: | |
| regs = iproc_pcie_reg_paxb_v2; | |
| pcie->iproc_cfg_read = true; | |
| pcie->has_apb_err_disable = true; | |
| if (pcie->need_ob_cfg) { | |
| pcie->ob_map = paxb_v2_ob_map; | |
| pcie->ob.nr_windows = ARRAY_SIZE(paxb_v2_ob_map); | |
| } | |
| pcie->ib.nr_regions = ARRAY_SIZE(paxb_v2_ib_map); | |
| pcie->ib_map = paxb_v2_ib_map; | |
| pcie->need_msi_steer = true; | |
| dev_warn(dev, "reads of config registers that contain %#x return incorrect data\n", | |
| CFG_RETRY_STATUS); | |
| break; | |
| case IPROC_PCIE_PAXC: | |
| regs = iproc_pcie_reg_paxc; | |
| pcie->ep_is_internal = true; | |
| pcie->iproc_cfg_read = true; | |
| pcie->rej_unconfig_pf = true; | |
| break; | |
| case IPROC_PCIE_PAXC_V2: | |
| regs = iproc_pcie_reg_paxc_v2; | |
| pcie->ep_is_internal = true; | |
| pcie->iproc_cfg_read = true; | |
| pcie->rej_unconfig_pf = true; | |
| pcie->need_msi_steer = true; | |
| break; | |
| default: | |
| dev_err(dev, "incompatible iProc PCIe interface\n"); | |
| return -EINVAL; | |
| } | |
| pcie->reg_offsets = devm_kcalloc(dev, IPROC_PCIE_MAX_NUM_REG, | |
| sizeof(*pcie->reg_offsets), | |
| GFP_KERNEL); | |
| if (!pcie->reg_offsets) | |
| return -ENOMEM; | |
| /* go through the register table and populate all valid registers */ | |
| pcie->reg_offsets[0] = (pcie->type == IPROC_PCIE_PAXC_V2) ? | |
| IPROC_PCIE_REG_INVALID : regs[0]; | |
| for (reg_idx = 1; reg_idx < IPROC_PCIE_MAX_NUM_REG; reg_idx++) | |
| pcie->reg_offsets[reg_idx] = regs[reg_idx] ? | |
| regs[reg_idx] : IPROC_PCIE_REG_INVALID; | |
| return 0; | |
| } | |
| int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res) | |
| { | |
| struct device *dev; | |
| int ret; | |
| struct pci_dev *pdev; | |
| struct pci_host_bridge *host = pci_host_bridge_from_priv(pcie); | |
| dev = pcie->dev; | |
| ret = iproc_pcie_rev_init(pcie); | |
| if (ret) { | |
| dev_err(dev, "unable to initialize controller parameters\n"); | |
| return ret; | |
| } | |
| ret = phy_init(pcie->phy); | |
| if (ret) { | |
| dev_err(dev, "unable to initialize PCIe PHY\n"); | |
| return ret; | |
| } | |
| ret = phy_power_on(pcie->phy); | |
| if (ret) { | |
| dev_err(dev, "unable to power on PCIe PHY\n"); | |
| goto err_exit_phy; | |
| } | |
| iproc_pcie_perst_ctrl(pcie, true); | |
| iproc_pcie_perst_ctrl(pcie, false); | |
| iproc_pcie_invalidate_mapping(pcie); | |
| if (pcie->need_ob_cfg) { | |
| ret = iproc_pcie_map_ranges(pcie, res); | |
| if (ret) { | |
| dev_err(dev, "map failed\n"); | |
| goto err_power_off_phy; | |
| } | |
| } | |
| if (pcie->need_ib_cfg) { | |
| ret = iproc_pcie_map_dma_ranges(pcie); | |
| if (ret && ret != -ENOENT) | |
| goto err_power_off_phy; | |
| } | |
| ret = iproc_pcie_check_link(pcie); | |
| if (ret) { | |
| dev_err(dev, "no PCIe EP device detected\n"); | |
| goto err_power_off_phy; | |
| } | |
| iproc_pcie_enable(pcie); | |
| if (IS_ENABLED(CONFIG_PCI_MSI)) | |
| if (iproc_pcie_msi_enable(pcie)) | |
| dev_info(dev, "not using iProc MSI\n"); | |
| host->ops = &iproc_pcie_ops; | |
| host->sysdata = pcie; | |
| ret = pci_host_probe(host); | |
| if (ret < 0) { | |
| dev_err(dev, "failed to scan host: %d\n", ret); | |
| goto err_power_off_phy; | |
| } | |
| for_each_pci_bridge(pdev, host->bus) { | |
| if (pci_pcie_type(pdev) == PCI_EXP_TYPE_ROOT_PORT) | |
| pcie_print_link_status(pdev); | |
| } | |
| return 0; | |
| err_power_off_phy: | |
| phy_power_off(pcie->phy); | |
| err_exit_phy: | |
| phy_exit(pcie->phy); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL(iproc_pcie_setup); | |
| void iproc_pcie_remove(struct iproc_pcie *pcie) | |
| { | |
| struct pci_host_bridge *host = pci_host_bridge_from_priv(pcie); | |
| pci_lock_rescan_remove(); | |
| pci_stop_root_bus(host->bus); | |
| pci_remove_root_bus(host->bus); | |
| pci_unlock_rescan_remove(); | |
| iproc_pcie_msi_disable(pcie); | |
| phy_power_off(pcie->phy); | |
| phy_exit(pcie->phy); | |
| } | |
| EXPORT_SYMBOL(iproc_pcie_remove); | |
| /* | |
| * The MSI parsing logic in certain revisions of Broadcom PAXC based root | |
| * complex does not work and needs to be disabled | |
| */ | |
| static void quirk_paxc_disable_msi_parsing(struct pci_dev *pdev) | |
| { | |
| struct iproc_pcie *pcie = iproc_data(pdev->bus); | |
| if (pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE) | |
| iproc_pcie_paxc_v2_msi_steer(pcie, 0, false); | |
| } | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0x16f0, | |
| quirk_paxc_disable_msi_parsing); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0xd802, | |
| quirk_paxc_disable_msi_parsing); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0xd804, | |
| quirk_paxc_disable_msi_parsing); | |
| static void quirk_paxc_bridge(struct pci_dev *pdev) | |
| { | |
| /* | |
| * The PCI config space is shared with the PAXC root port and the first | |
| * Ethernet device. So, we need to workaround this by telling the PCI | |
| * code that the bridge is not an Ethernet device. | |
| */ | |
| if (pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE) | |
| pdev->class = PCI_CLASS_BRIDGE_PCI_NORMAL; | |
| /* | |
| * MPSS is not being set properly (as it is currently 0). This is | |
| * because that area of the PCI config space is hard coded to zero, and | |
| * is not modifiable by firmware. Set this to 2 (e.g., 512 byte MPS) | |
| * so that the MPS can be set to the real max value. | |
| */ | |
| pdev->pcie_mpss = 2; | |
| } | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0x16cd, quirk_paxc_bridge); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0x16f0, quirk_paxc_bridge); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0xd750, quirk_paxc_bridge); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0xd802, quirk_paxc_bridge); | |
| DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_BROADCOM, 0xd804, quirk_paxc_bridge); | |
| MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>"); | |
| MODULE_DESCRIPTION("Broadcom iPROC PCIe common driver"); | |
| MODULE_LICENSE("GPL v2"); |