| // SPDX-License-Identifier: GPL-2.0+ | |
| /* Copyright (C) 2009 - 2019 Broadcom */ | |
| #include <linux/bitfield.h> | |
| #include <linux/bitops.h> | |
| #include <linux/clk.h> | |
| #include <linux/compiler.h> | |
| #include <linux/delay.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/ioport.h> | |
| #include <linux/irqchip/chained_irq.h> | |
| #include <linux/irqchip/irq-msi-lib.h> | |
| #include <linux/irqdomain.h> | |
| #include <linux/kdebug.h> | |
| #include <linux/kernel.h> | |
| #include <linux/list.h> | |
| #include <linux/log2.h> | |
| #include <linux/module.h> | |
| #include <linux/msi.h> | |
| #include <linux/notifier.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_pci.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/panic_notifier.h> | |
| #include <linux/pci.h> | |
| #include <linux/pci-ecam.h> | |
| #include <linux/printk.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <linux/reset.h> | |
| #include <linux/sizes.h> | |
| #include <linux/slab.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/string.h> | |
| #include <linux/string_choices.h> | |
| #include <linux/types.h> | |
| #include "../pci.h" | |
| /* BRCM_PCIE_CAP_REGS - Offset for the mandatory capability config regs */ | |
| #define BRCM_PCIE_CAP_REGS 0x00ac | |
| /* Broadcom STB PCIe Register Offsets */ | |
| #define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1 0x0188 | |
| #define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK 0xc | |
| #define PCIE_RC_CFG_VENDOR_SPECIFIC_REG1_LITTLE_ENDIAN 0x0 | |
| #define PCIE_RC_CFG_PRIV1_ID_VAL3 0x043c | |
| #define PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK 0xffffff | |
| #define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY 0x04dc | |
| #define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_MAX_LINK_WIDTH_MASK 0x1f0 | |
| #define PCIE_RC_CFG_PRIV1_ROOT_CAP 0x4f8 | |
| #define PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK 0xf8 | |
| #define PCIE_RC_DL_MDIO_ADDR 0x1100 | |
| #define PCIE_RC_DL_MDIO_WR_DATA 0x1104 | |
| #define PCIE_RC_DL_MDIO_RD_DATA 0x1108 | |
| #define PCIE_RC_PL_REG_PHY_CTL_1 0x1804 | |
| #define PCIE_RC_PL_REG_PHY_CTL_1_REG_P2_POWERDOWN_ENA_NOSYNC_MASK 0x8 | |
| #define PCIE_RC_PL_PHY_CTL_15 0x184c | |
| #define PCIE_RC_PL_PHY_CTL_15_DIS_PLL_PD_MASK 0x400000 | |
| #define PCIE_RC_PL_PHY_CTL_15_PM_CLK_PERIOD_MASK 0xff | |
| #define PCIE_MISC_MISC_CTRL 0x4008 | |
| #define PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK 0x80 | |
| #define PCIE_MISC_MISC_CTRL_PCIE_RCB_MPS_MODE_MASK 0x400 | |
| #define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK 0x1000 | |
| #define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK 0x2000 | |
| #define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000 | |
| #define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK 0xf8000000 | |
| #define PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK 0x07c00000 | |
| #define PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK 0x0000001f | |
| #define SCB_SIZE_MASK(x) PCIE_MISC_MISC_CTRL_SCB ## x ## _SIZE_MASK | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO 0x400c | |
| #define PCIE_MEM_WIN0_LO(win) \ | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 8) | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI 0x4010 | |
| #define PCIE_MEM_WIN0_HI(win) \ | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8) | |
| /* | |
| * NOTE: You may see the term "BAR" in a number of register names used by | |
| * this driver. The term is an artifact of when the HW core was an | |
| * endpoint device (EP). Now it is a root complex (RC) and anywhere a | |
| * register has the term "BAR" it is related to an inbound window. | |
| */ | |
| #define PCIE_BRCM_MAX_INBOUND_WINS 16 | |
| #define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c | |
| #define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f | |
| #define PCIE_MISC_RC_BAR4_CONFIG_LO 0x40d4 | |
| #define PCIE_MISC_MSI_BAR_CONFIG_LO 0x4044 | |
| #define PCIE_MISC_MSI_BAR_CONFIG_HI 0x4048 | |
| #define PCIE_MISC_MSI_DATA_CONFIG 0x404c | |
| #define PCIE_MISC_MSI_DATA_CONFIG_VAL_32 0xffe06540 | |
| #define PCIE_MISC_MSI_DATA_CONFIG_VAL_8 0xfff86540 | |
| #define PCIE_MISC_PCIE_CTRL 0x4064 | |
| #define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1 | |
| #define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK 0x4 | |
| #define PCIE_MISC_PCIE_STATUS 0x4068 | |
| #define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80 | |
| #define PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK 0x20 | |
| #define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK 0x10 | |
| #define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK 0x40 | |
| #define PCIE_MISC_REVISION 0x406c | |
| #define BRCM_PCIE_HW_REV_33 0x0303 | |
| #define BRCM_PCIE_HW_REV_3_20 0x0320 | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT 0x4070 | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK 0xfff00000 | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK 0xfff0 | |
| #define PCIE_MEM_WIN0_BASE_LIMIT(win) \ | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT + ((win) * 4) | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI 0x4080 | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK 0xff | |
| #define PCIE_MEM_WIN0_BASE_HI(win) \ | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI + ((win) * 8) | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI 0x4084 | |
| #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK 0xff | |
| #define PCIE_MEM_WIN0_LIMIT_HI(win) \ | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI + ((win) * 8) | |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2 | |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK 0x200000 | |
| #define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000 | |
| #define PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x00800000 | |
| #define PCIE_CLKREQ_MASK \ | |
| (PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK | \ | |
| PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK) | |
| #define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP 0x40ac | |
| #define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK BIT(0) | |
| #define PCIE_MISC_UBUS_BAR4_CONFIG_REMAP 0x410c | |
| #define PCIE_MSI_INTR2_BASE 0x4500 | |
| /* Offsets from INTR2_CPU and MSI_INTR2 BASE offsets */ | |
| #define MSI_INT_STATUS 0x0 | |
| #define MSI_INT_CLR 0x8 | |
| #define MSI_INT_MASK_SET 0x10 | |
| #define MSI_INT_MASK_CLR 0x14 | |
| /* Error report registers */ | |
| #define PCIE_OUTB_ERR_TREAT 0x6000 | |
| #define PCIE_OUTB_ERR_TREAT_CONFIG 0x1 | |
| #define PCIE_OUTB_ERR_TREAT_MEM 0x2 | |
| #define PCIE_OUTB_ERR_VALID 0x6004 | |
| #define PCIE_OUTB_ERR_CLEAR 0x6008 | |
| #define PCIE_OUTB_ERR_ACC_INFO 0x600c | |
| #define PCIE_OUTB_ERR_ACC_INFO_CFG_ERR BIT(0) | |
| #define PCIE_OUTB_ERR_ACC_INFO_MEM_ERR BIT(1) | |
| #define PCIE_OUTB_ERR_ACC_INFO_TYPE_64 BIT(2) | |
| #define PCIE_OUTB_ERR_ACC_INFO_DIR_WRITE BIT(4) | |
| #define PCIE_OUTB_ERR_ACC_INFO_BYTE_LANES 0xff00 | |
| #define PCIE_OUTB_ERR_ACC_ADDR 0x6010 | |
| #define PCIE_OUTB_ERR_ACC_ADDR_BUS 0xff00000 | |
| #define PCIE_OUTB_ERR_ACC_ADDR_DEV 0xf8000 | |
| #define PCIE_OUTB_ERR_ACC_ADDR_FUNC 0x7000 | |
| #define PCIE_OUTB_ERR_ACC_ADDR_REG 0xfff | |
| #define PCIE_OUTB_ERR_CFG_CAUSE 0x6014 | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_TIMEOUT BIT(6) | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_ABORT BIT(5) | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_UNSUPP_REQ BIT(4) | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_ACC_TIMEOUT BIT(2) | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_ACC_DISABLED BIT(1) | |
| #define PCIE_OUTB_ERR_CFG_CAUSE_ACC_64BIT BIT(0) | |
| #define PCIE_OUTB_ERR_MEM_ADDR_LO 0x6018 | |
| #define PCIE_OUTB_ERR_MEM_ADDR_HI 0x601c | |
| #define PCIE_OUTB_ERR_MEM_CAUSE 0x6020 | |
| #define PCIE_OUTB_ERR_MEM_CAUSE_TIMEOUT BIT(6) | |
| #define PCIE_OUTB_ERR_MEM_CAUSE_ABORT BIT(5) | |
| #define PCIE_OUTB_ERR_MEM_CAUSE_UNSUPP_REQ BIT(4) | |
| #define PCIE_OUTB_ERR_MEM_CAUSE_ACC_DISABLED BIT(1) | |
| #define PCIE_OUTB_ERR_MEM_CAUSE_BAD_ADDR BIT(0) | |
| #define PCIE_RGR1_SW_INIT_1_PERST_MASK 0x1 | |
| #define RGR1_SW_INIT_1_INIT_GENERIC_MASK 0x2 | |
| #define RGR1_SW_INIT_1_INIT_GENERIC_SHIFT 0x1 | |
| #define RGR1_SW_INIT_1_INIT_7278_MASK 0x1 | |
| #define RGR1_SW_INIT_1_INIT_7278_SHIFT 0x0 | |
| /* PCIe parameters */ | |
| #define BRCM_NUM_PCIE_OUT_WINS 0x4 | |
| #define BRCM_INT_PCI_MSI_NR 32 | |
| #define BRCM_INT_PCI_MSI_LEGACY_NR 8 | |
| #define BRCM_INT_PCI_MSI_SHIFT 0 | |
| #define BRCM_INT_PCI_MSI_MASK GENMASK(BRCM_INT_PCI_MSI_NR - 1, 0) | |
| #define BRCM_INT_PCI_MSI_LEGACY_MASK GENMASK(31, \ | |
| 32 - BRCM_INT_PCI_MSI_LEGACY_NR) | |
| /* MSI target addresses */ | |
| #define BRCM_MSI_TARGET_ADDR_LT_4GB 0x0fffffffcULL | |
| #define BRCM_MSI_TARGET_ADDR_GT_4GB 0xffffffffcULL | |
| /* MDIO registers */ | |
| #define MDIO_PORT0 0x0 | |
| #define MDIO_DATA_MASK 0x7fffffff | |
| #define MDIO_PORT_MASK 0xf0000 | |
| #define MDIO_PORT_EXT_MASK 0x200000 | |
| #define MDIO_REGAD_MASK 0xffff | |
| #define MDIO_CMD_MASK 0x00100000 | |
| #define MDIO_CMD_READ 0x1 | |
| #define MDIO_CMD_WRITE 0x0 | |
| #define MDIO_DATA_DONE_MASK 0x80000000 | |
| #define MDIO_RD_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 1 : 0) | |
| #define MDIO_WT_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 0 : 1) | |
| #define SSC_REGS_ADDR 0x1100 | |
| #define SET_ADDR_OFFSET 0x1f | |
| #define SSC_CNTL_OFFSET 0x2 | |
| #define SSC_CNTL_OVRD_EN_MASK 0x8000 | |
| #define SSC_CNTL_OVRD_VAL_MASK 0x4000 | |
| #define SSC_STATUS_OFFSET 0x1 | |
| #define SSC_STATUS_SSC_MASK 0x400 | |
| #define SSC_STATUS_PLL_LOCK_MASK 0x800 | |
| #define PCIE_BRCM_MAX_MEMC 3 | |
| #define IDX_ADDR(pcie) ((pcie)->cfg->offsets[EXT_CFG_INDEX]) | |
| #define DATA_ADDR(pcie) ((pcie)->cfg->offsets[EXT_CFG_DATA]) | |
| #define PCIE_RGR1_SW_INIT_1(pcie) ((pcie)->cfg->offsets[RGR1_SW_INIT_1]) | |
| #define HARD_DEBUG(pcie) ((pcie)->cfg->offsets[PCIE_HARD_DEBUG]) | |
| #define INTR2_CPU_BASE(pcie) ((pcie)->cfg->offsets[PCIE_INTR2_CPU_BASE]) | |
| /* Rescal registers */ | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL 0xc700 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS 0x3 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK 0x4 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT 0x2 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK 0x2 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT 0x1 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK 0x1 | |
| #define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT 0x0 | |
| /* Forward declarations */ | |
| struct brcm_pcie; | |
| enum { | |
| RGR1_SW_INIT_1, | |
| EXT_CFG_INDEX, | |
| EXT_CFG_DATA, | |
| PCIE_HARD_DEBUG, | |
| PCIE_INTR2_CPU_BASE, | |
| }; | |
| enum pcie_soc_base { | |
| GENERIC, | |
| BCM2711, | |
| BCM4908, | |
| BCM7278, | |
| BCM7425, | |
| BCM7435, | |
| BCM7712, | |
| }; | |
| struct inbound_win { | |
| u64 size; | |
| u64 pci_offset; | |
| u64 cpu_addr; | |
| }; | |
| /* | |
| * The RESCAL block is tied to PCIe controller #1, regardless of the number of | |
| * controllers, and turning off PCIe controller #1 prevents access to the RESCAL | |
| * register blocks, therefore no other controller can access this register | |
| * space, and depending upon the bus fabric we may get a timeout (UBUS/GISB), | |
| * or a hang (AXI). | |
| */ | |
| #define CFG_QUIRK_AVOID_BRIDGE_SHUTDOWN BIT(0) | |
| struct pcie_cfg_data { | |
| const int *offsets; | |
| const enum pcie_soc_base soc_base; | |
| const bool has_phy; | |
| const u32 quirks; | |
| u8 num_inbound_wins; | |
| int (*perst_set)(struct brcm_pcie *pcie, u32 val); | |
| int (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val); | |
| int (*post_setup)(struct brcm_pcie *pcie); | |
| bool has_err_report; | |
| }; | |
| struct subdev_regulators { | |
| unsigned int num_supplies; | |
| struct regulator_bulk_data supplies[]; | |
| }; | |
| struct brcm_msi { | |
| struct device *dev; | |
| void __iomem *base; | |
| struct device_node *np; | |
| struct irq_domain *inner_domain; | |
| struct mutex lock; /* guards the alloc/free operations */ | |
| u64 target_addr; | |
| int irq; | |
| DECLARE_BITMAP(used, BRCM_INT_PCI_MSI_NR); | |
| bool legacy; | |
| /* Some chips have MSIs in bits [31..24] of a shared register. */ | |
| int legacy_shift; | |
| int nr; /* No. of MSI available, depends on chip */ | |
| /* This is the base pointer for interrupt status/set/clr regs */ | |
| void __iomem *intr_base; | |
| }; | |
| /* Internal PCIe Host Controller Information.*/ | |
| struct brcm_pcie { | |
| struct device *dev; | |
| void __iomem *base; | |
| struct clk *clk; | |
| struct device_node *np; | |
| bool ssc; | |
| int gen; | |
| u64 msi_target_addr; | |
| struct brcm_msi *msi; | |
| struct reset_control *rescal; | |
| struct reset_control *perst_reset; | |
| struct reset_control *bridge_reset; | |
| struct reset_control *swinit_reset; | |
| int num_memc; | |
| u64 memc_size[PCIE_BRCM_MAX_MEMC]; | |
| u32 hw_rev; | |
| struct subdev_regulators *sr; | |
| bool ep_wakeup_capable; | |
| const struct pcie_cfg_data *cfg; | |
| bool bridge_in_reset; | |
| struct notifier_block die_notifier; | |
| struct notifier_block panic_notifier; | |
| spinlock_t bridge_lock; | |
| }; | |
| static inline bool is_bmips(const struct brcm_pcie *pcie) | |
| { | |
| return pcie->cfg->soc_base == BCM7435 || pcie->cfg->soc_base == BCM7425; | |
| } | |
| static int brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val) | |
| { | |
| unsigned long flags; | |
| int ret; | |
| if (pcie->cfg->has_err_report) | |
| spin_lock_irqsave(&pcie->bridge_lock, flags); | |
| ret = pcie->cfg->bridge_sw_init_set(pcie, val); | |
| /* If we fail, assume the bridge is in reset (off) */ | |
| pcie->bridge_in_reset = ret ? true : val; | |
| if (pcie->cfg->has_err_report) | |
| spin_unlock_irqrestore(&pcie->bridge_lock, flags); | |
| return ret; | |
| } | |
| /* | |
| * This is to convert the size of the inbound "BAR" region to the | |
| * non-linear values of PCIE_X_MISC_RC_BAR[123]_CONFIG_LO.SIZE | |
| */ | |
| static int brcm_pcie_encode_ibar_size(u64 size) | |
| { | |
| int log2_in = ilog2(size); | |
| if (log2_in >= 12 && log2_in <= 15) | |
| /* Covers 4KB to 32KB (inclusive) */ | |
| return (log2_in - 12) + 0x1c; | |
| else if (log2_in >= 16 && log2_in <= 36) | |
| /* Covers 64KB to 64GB, (inclusive) */ | |
| return log2_in - 15; | |
| /* Something is awry so disable */ | |
| return 0; | |
| } | |
| static u32 brcm_pcie_mdio_form_pkt(int port, int regad, int cmd) | |
| { | |
| u32 pkt = 0; | |
| pkt |= FIELD_PREP(MDIO_PORT_EXT_MASK, port >> 4); | |
| pkt |= FIELD_PREP(MDIO_PORT_MASK, port); | |
| pkt |= FIELD_PREP(MDIO_REGAD_MASK, regad); | |
| pkt |= FIELD_PREP(MDIO_CMD_MASK, cmd); | |
| return pkt; | |
| } | |
| /* negative return value indicates error */ | |
| static int brcm_pcie_mdio_read(void __iomem *base, u8 port, u8 regad, u32 *val) | |
| { | |
| u32 data; | |
| int err; | |
| writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_READ), | |
| base + PCIE_RC_DL_MDIO_ADDR); | |
| readl(base + PCIE_RC_DL_MDIO_ADDR); | |
| err = readl_poll_timeout_atomic(base + PCIE_RC_DL_MDIO_RD_DATA, data, | |
| MDIO_RD_DONE(data), 10, 100); | |
| *val = FIELD_GET(MDIO_DATA_MASK, data); | |
| return err; | |
| } | |
| /* negative return value indicates error */ | |
| static int brcm_pcie_mdio_write(void __iomem *base, u8 port, | |
| u8 regad, u16 wrdata) | |
| { | |
| u32 data; | |
| int err; | |
| writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_WRITE), | |
| base + PCIE_RC_DL_MDIO_ADDR); | |
| readl(base + PCIE_RC_DL_MDIO_ADDR); | |
| writel(MDIO_DATA_DONE_MASK | wrdata, base + PCIE_RC_DL_MDIO_WR_DATA); | |
| err = readl_poll_timeout_atomic(base + PCIE_RC_DL_MDIO_WR_DATA, data, | |
| MDIO_WT_DONE(data), 10, 100); | |
| return err; | |
| } | |
| /* | |
| * Configures device for Spread Spectrum Clocking (SSC) mode; a negative | |
| * return value indicates error. | |
| */ | |
| static int brcm_pcie_set_ssc(struct brcm_pcie *pcie) | |
| { | |
| int pll, ssc; | |
| int ret; | |
| u32 tmp; | |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, SET_ADDR_OFFSET, | |
| SSC_REGS_ADDR); | |
| if (ret < 0) | |
| return ret; | |
| ret = brcm_pcie_mdio_read(pcie->base, MDIO_PORT0, | |
| SSC_CNTL_OFFSET, &tmp); | |
| if (ret < 0) | |
| return ret; | |
| u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_EN_MASK); | |
| u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_VAL_MASK); | |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, | |
| SSC_CNTL_OFFSET, tmp); | |
| if (ret < 0) | |
| return ret; | |
| usleep_range(1000, 2000); | |
| ret = brcm_pcie_mdio_read(pcie->base, MDIO_PORT0, | |
| SSC_STATUS_OFFSET, &tmp); | |
| if (ret < 0) | |
| return ret; | |
| ssc = FIELD_GET(SSC_STATUS_SSC_MASK, tmp); | |
| pll = FIELD_GET(SSC_STATUS_PLL_LOCK_MASK, tmp); | |
| return ssc && pll ? 0 : -EIO; | |
| } | |
| /* Limits operation to a specific generation (1, 2, or 3) */ | |
| static void brcm_pcie_set_gen(struct brcm_pcie *pcie, int gen) | |
| { | |
| u16 lnkctl2 = readw(pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); | |
| u32 lnkcap = readl(pcie->base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); | |
| u32p_replace_bits(&lnkcap, gen, PCI_EXP_LNKCAP_SLS); | |
| writel(lnkcap, pcie->base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); | |
| u16p_replace_bits(&lnkctl2, gen, PCI_EXP_LNKCTL2_TLS); | |
| writew(lnkctl2, pcie->base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); | |
| } | |
| static void brcm_pcie_set_outbound_win(struct brcm_pcie *pcie, | |
| u8 win, u64 cpu_addr, | |
| u64 pcie_addr, u64 size) | |
| { | |
| u32 cpu_addr_mb_high, limit_addr_mb_high; | |
| phys_addr_t cpu_addr_mb, limit_addr_mb; | |
| int high_addr_shift; | |
| u32 tmp; | |
| /* Set the base of the pcie_addr window */ | |
| writel(lower_32_bits(pcie_addr), pcie->base + PCIE_MEM_WIN0_LO(win)); | |
| writel(upper_32_bits(pcie_addr), pcie->base + PCIE_MEM_WIN0_HI(win)); | |
| /* Write the addr base & limit lower bits (in MBs) */ | |
| cpu_addr_mb = cpu_addr / SZ_1M; | |
| limit_addr_mb = (cpu_addr + size - 1) / SZ_1M; | |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_BASE_LIMIT(win)); | |
| u32p_replace_bits(&tmp, cpu_addr_mb, | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK); | |
| u32p_replace_bits(&tmp, limit_addr_mb, | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK); | |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_BASE_LIMIT(win)); | |
| if (is_bmips(pcie)) | |
| return; | |
| /* Write the cpu & limit addr upper bits */ | |
| high_addr_shift = | |
| HWEIGHT32(PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK); | |
| cpu_addr_mb_high = cpu_addr_mb >> high_addr_shift; | |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_BASE_HI(win)); | |
| u32p_replace_bits(&tmp, cpu_addr_mb_high, | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK); | |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_BASE_HI(win)); | |
| limit_addr_mb_high = limit_addr_mb >> high_addr_shift; | |
| tmp = readl(pcie->base + PCIE_MEM_WIN0_LIMIT_HI(win)); | |
| u32p_replace_bits(&tmp, limit_addr_mb_high, | |
| PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK); | |
| writel(tmp, pcie->base + PCIE_MEM_WIN0_LIMIT_HI(win)); | |
| } | |
| #define BRCM_MSI_FLAGS_REQUIRED (MSI_FLAG_USE_DEF_DOM_OPS | \ | |
| MSI_FLAG_USE_DEF_CHIP_OPS | \ | |
| MSI_FLAG_NO_AFFINITY) | |
| #define BRCM_MSI_FLAGS_SUPPORTED (MSI_GENERIC_FLAGS_MASK | \ | |
| MSI_FLAG_MULTI_PCI_MSI) | |
| static const struct msi_parent_ops brcm_msi_parent_ops = { | |
| .required_flags = BRCM_MSI_FLAGS_REQUIRED, | |
| .supported_flags = BRCM_MSI_FLAGS_SUPPORTED, | |
| .bus_select_token = DOMAIN_BUS_PCI_MSI, | |
| .chip_flags = MSI_CHIP_FLAG_SET_ACK, | |
| .prefix = "BRCM-", | |
| .init_dev_msi_info = msi_lib_init_dev_msi_info, | |
| }; | |
| static void brcm_pcie_msi_isr(struct irq_desc *desc) | |
| { | |
| struct irq_chip *chip = irq_desc_get_chip(desc); | |
| unsigned long status; | |
| struct brcm_msi *msi; | |
| struct device *dev; | |
| u32 bit; | |
| chained_irq_enter(chip, desc); | |
| msi = irq_desc_get_handler_data(desc); | |
| dev = msi->dev; | |
| status = readl(msi->intr_base + MSI_INT_STATUS); | |
| status >>= msi->legacy_shift; | |
| for_each_set_bit(bit, &status, msi->nr) { | |
| int ret; | |
| ret = generic_handle_domain_irq(msi->inner_domain, bit); | |
| if (ret) | |
| dev_dbg(dev, "unexpected MSI\n"); | |
| } | |
| chained_irq_exit(chip, desc); | |
| } | |
| static void brcm_msi_compose_msi_msg(struct irq_data *data, struct msi_msg *msg) | |
| { | |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(data); | |
| msg->address_lo = lower_32_bits(msi->target_addr); | |
| msg->address_hi = upper_32_bits(msi->target_addr); | |
| msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL_32) | data->hwirq; | |
| } | |
| static void brcm_msi_ack_irq(struct irq_data *data) | |
| { | |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(data); | |
| const int shift_amt = data->hwirq + msi->legacy_shift; | |
| writel(1 << shift_amt, msi->intr_base + MSI_INT_CLR); | |
| } | |
| static struct irq_chip brcm_msi_bottom_irq_chip = { | |
| .name = "BRCM STB MSI", | |
| .irq_compose_msi_msg = brcm_msi_compose_msi_msg, | |
| .irq_ack = brcm_msi_ack_irq, | |
| }; | |
| static int brcm_msi_alloc(struct brcm_msi *msi, unsigned int nr_irqs) | |
| { | |
| int hwirq; | |
| mutex_lock(&msi->lock); | |
| hwirq = bitmap_find_free_region(msi->used, msi->nr, | |
| order_base_2(nr_irqs)); | |
| mutex_unlock(&msi->lock); | |
| return hwirq; | |
| } | |
| static void brcm_msi_free(struct brcm_msi *msi, unsigned long hwirq, | |
| unsigned int nr_irqs) | |
| { | |
| mutex_lock(&msi->lock); | |
| bitmap_release_region(msi->used, hwirq, order_base_2(nr_irqs)); | |
| mutex_unlock(&msi->lock); | |
| } | |
| static int brcm_irq_domain_alloc(struct irq_domain *domain, unsigned int virq, | |
| unsigned int nr_irqs, void *args) | |
| { | |
| struct brcm_msi *msi = domain->host_data; | |
| int hwirq, i; | |
| hwirq = brcm_msi_alloc(msi, nr_irqs); | |
| if (hwirq < 0) | |
| return hwirq; | |
| for (i = 0; i < nr_irqs; i++) | |
| irq_domain_set_info(domain, virq + i, (irq_hw_number_t)hwirq + i, | |
| &brcm_msi_bottom_irq_chip, domain->host_data, | |
| handle_edge_irq, NULL, NULL); | |
| return 0; | |
| } | |
| static void brcm_irq_domain_free(struct irq_domain *domain, | |
| unsigned int virq, unsigned int nr_irqs) | |
| { | |
| struct irq_data *d = irq_domain_get_irq_data(domain, virq); | |
| struct brcm_msi *msi = irq_data_get_irq_chip_data(d); | |
| brcm_msi_free(msi, d->hwirq, nr_irqs); | |
| } | |
| static const struct irq_domain_ops msi_domain_ops = { | |
| .alloc = brcm_irq_domain_alloc, | |
| .free = brcm_irq_domain_free, | |
| }; | |
| static int brcm_allocate_domains(struct brcm_msi *msi) | |
| { | |
| struct device *dev = msi->dev; | |
| struct irq_domain_info info = { | |
| .fwnode = of_fwnode_handle(msi->np), | |
| .ops = &msi_domain_ops, | |
| .host_data = msi, | |
| .size = msi->nr, | |
| }; | |
| msi->inner_domain = msi_create_parent_irq_domain(&info, &brcm_msi_parent_ops); | |
| if (!msi->inner_domain) { | |
| dev_err(dev, "failed to create MSI domain\n"); | |
| return -ENOMEM; | |
| } | |
| return 0; | |
| } | |
| static void brcm_free_domains(struct brcm_msi *msi) | |
| { | |
| irq_domain_remove(msi->inner_domain); | |
| } | |
| static void brcm_msi_remove(struct brcm_pcie *pcie) | |
| { | |
| struct brcm_msi *msi = pcie->msi; | |
| if (!msi) | |
| return; | |
| irq_set_chained_handler_and_data(msi->irq, NULL, NULL); | |
| brcm_free_domains(msi); | |
| } | |
| static void brcm_msi_set_regs(struct brcm_msi *msi) | |
| { | |
| u32 val = msi->legacy ? BRCM_INT_PCI_MSI_LEGACY_MASK : | |
| BRCM_INT_PCI_MSI_MASK; | |
| writel(val, msi->intr_base + MSI_INT_MASK_CLR); | |
| writel(val, msi->intr_base + MSI_INT_CLR); | |
| /* | |
| * The 0 bit of PCIE_MISC_MSI_BAR_CONFIG_LO is repurposed to MSI | |
| * enable, which we set to 1. | |
| */ | |
| writel(lower_32_bits(msi->target_addr) | 0x1, | |
| msi->base + PCIE_MISC_MSI_BAR_CONFIG_LO); | |
| writel(upper_32_bits(msi->target_addr), | |
| msi->base + PCIE_MISC_MSI_BAR_CONFIG_HI); | |
| val = msi->legacy ? PCIE_MISC_MSI_DATA_CONFIG_VAL_8 : PCIE_MISC_MSI_DATA_CONFIG_VAL_32; | |
| writel(val, msi->base + PCIE_MISC_MSI_DATA_CONFIG); | |
| } | |
| static int brcm_pcie_enable_msi(struct brcm_pcie *pcie) | |
| { | |
| struct brcm_msi *msi; | |
| int irq, ret; | |
| struct device *dev = pcie->dev; | |
| irq = irq_of_parse_and_map(dev->of_node, 1); | |
| if (irq <= 0) { | |
| dev_err(dev, "cannot map MSI interrupt\n"); | |
| return -ENODEV; | |
| } | |
| msi = devm_kzalloc(dev, sizeof(struct brcm_msi), GFP_KERNEL); | |
| if (!msi) | |
| return -ENOMEM; | |
| mutex_init(&msi->lock); | |
| msi->dev = dev; | |
| msi->base = pcie->base; | |
| msi->np = pcie->np; | |
| msi->target_addr = pcie->msi_target_addr; | |
| msi->irq = irq; | |
| msi->legacy = pcie->hw_rev < BRCM_PCIE_HW_REV_33; | |
| /* | |
| * Sanity check to make sure that the 'used' bitmap in struct brcm_msi | |
| * is large enough. | |
| */ | |
| BUILD_BUG_ON(BRCM_INT_PCI_MSI_LEGACY_NR > BRCM_INT_PCI_MSI_NR); | |
| if (msi->legacy) { | |
| msi->intr_base = msi->base + INTR2_CPU_BASE(pcie); | |
| msi->nr = BRCM_INT_PCI_MSI_LEGACY_NR; | |
| msi->legacy_shift = 24; | |
| } else { | |
| msi->intr_base = msi->base + PCIE_MSI_INTR2_BASE; | |
| msi->nr = BRCM_INT_PCI_MSI_NR; | |
| msi->legacy_shift = 0; | |
| } | |
| ret = brcm_allocate_domains(msi); | |
| if (ret) | |
| return ret; | |
| irq_set_chained_handler_and_data(msi->irq, brcm_pcie_msi_isr, msi); | |
| brcm_msi_set_regs(msi); | |
| pcie->msi = msi; | |
| return 0; | |
| } | |
| /* The controller is capable of serving in both RC and EP roles */ | |
| static bool brcm_pcie_rc_mode(struct brcm_pcie *pcie) | |
| { | |
| void __iomem *base = pcie->base; | |
| u32 val = readl(base + PCIE_MISC_PCIE_STATUS); | |
| return !!FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK, val); | |
| } | |
| static bool brcm_pcie_link_up(struct brcm_pcie *pcie) | |
| { | |
| u32 val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); | |
| u32 dla = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK, val); | |
| u32 plu = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK, val); | |
| return dla && plu; | |
| } | |
| static void __iomem *brcm_pcie_map_bus(struct pci_bus *bus, | |
| unsigned int devfn, int where) | |
| { | |
| struct brcm_pcie *pcie = bus->sysdata; | |
| void __iomem *base = pcie->base; | |
| int idx; | |
| /* Accesses to the RC go right to the RC registers if !devfn */ | |
| if (pci_is_root_bus(bus)) | |
| return devfn ? NULL : base + PCIE_ECAM_REG(where); | |
| /* An access to our HW w/o link-up will cause a CPU Abort */ | |
| if (!brcm_pcie_link_up(pcie)) | |
| return NULL; | |
| /* For devices, write to the config space index register */ | |
| idx = PCIE_ECAM_OFFSET(bus->number, devfn, 0); | |
| writel(idx, base + IDX_ADDR(pcie)); | |
| return base + DATA_ADDR(pcie) + PCIE_ECAM_REG(where); | |
| } | |
| static void __iomem *brcm7425_pcie_map_bus(struct pci_bus *bus, | |
| unsigned int devfn, int where) | |
| { | |
| struct brcm_pcie *pcie = bus->sysdata; | |
| void __iomem *base = pcie->base; | |
| int idx; | |
| /* Accesses to the RC go right to the RC registers if !devfn */ | |
| if (pci_is_root_bus(bus)) | |
| return devfn ? NULL : base + PCIE_ECAM_REG(where); | |
| /* An access to our HW w/o link-up will cause a CPU Abort */ | |
| if (!brcm_pcie_link_up(pcie)) | |
| return NULL; | |
| /* For devices, write to the config space index register */ | |
| idx = PCIE_ECAM_OFFSET(bus->number, devfn, where); | |
| writel(idx, base + IDX_ADDR(pcie)); | |
| return base + DATA_ADDR(pcie); | |
| } | |
| static int brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val) | |
| { | |
| u32 tmp, mask = RGR1_SW_INIT_1_INIT_GENERIC_MASK; | |
| u32 shift = RGR1_SW_INIT_1_INIT_GENERIC_SHIFT; | |
| int ret = 0; | |
| if (pcie->bridge_reset) { | |
| if (val) | |
| ret = reset_control_assert(pcie->bridge_reset); | |
| else | |
| ret = reset_control_deassert(pcie->bridge_reset); | |
| if (ret) | |
| dev_err(pcie->dev, "failed to %s 'bridge' reset, err=%d\n", | |
| val ? "assert" : "deassert", ret); | |
| return ret; | |
| } | |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| tmp = (tmp & ~mask) | ((val << shift) & mask); | |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| return ret; | |
| } | |
| static int brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val) | |
| { | |
| u32 tmp, mask = RGR1_SW_INIT_1_INIT_7278_MASK; | |
| u32 shift = RGR1_SW_INIT_1_INIT_7278_SHIFT; | |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| tmp = (tmp & ~mask) | ((val << shift) & mask); | |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| return 0; | |
| } | |
| static int brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val) | |
| { | |
| int ret; | |
| if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n")) | |
| return -EINVAL; | |
| if (val) | |
| ret = reset_control_assert(pcie->perst_reset); | |
| else | |
| ret = reset_control_deassert(pcie->perst_reset); | |
| if (ret) | |
| dev_err(pcie->dev, "failed to %s 'perst' reset, err=%d\n", | |
| val ? "assert" : "deassert", ret); | |
| return ret; | |
| } | |
| static int brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val) | |
| { | |
| u32 tmp; | |
| /* Perst bit has moved and assert value is 0 */ | |
| tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL); | |
| u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK); | |
| writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL); | |
| return 0; | |
| } | |
| static int brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val) | |
| { | |
| u32 tmp; | |
| tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); | |
| writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); | |
| return 0; | |
| } | |
| static int brcm_pcie_post_setup_bcm2712(struct brcm_pcie *pcie) | |
| { | |
| static const u16 data[] = { 0x50b9, 0xbda1, 0x0094, 0x97b4, 0x5030, | |
| 0x5030, 0x0007 }; | |
| static const u8 regs[] = { 0x16, 0x17, 0x18, 0x19, 0x1b, 0x1c, 0x1e }; | |
| int ret, i; | |
| u32 tmp; | |
| /* Allow a 54MHz (xosc) refclk source */ | |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, SET_ADDR_OFFSET, 0x1600); | |
| if (ret < 0) | |
| return ret; | |
| for (i = 0; i < ARRAY_SIZE(regs); i++) { | |
| ret = brcm_pcie_mdio_write(pcie->base, MDIO_PORT0, regs[i], data[i]); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| usleep_range(100, 200); | |
| /* | |
| * Set L1SS sub-state timers to avoid lengthy state transitions, | |
| * PM clock period is 18.52ns (1/54MHz, round down). | |
| */ | |
| tmp = readl(pcie->base + PCIE_RC_PL_PHY_CTL_15); | |
| tmp &= ~PCIE_RC_PL_PHY_CTL_15_PM_CLK_PERIOD_MASK; | |
| tmp |= 0x12; | |
| writel(tmp, pcie->base + PCIE_RC_PL_PHY_CTL_15); | |
| return 0; | |
| } | |
| static void add_inbound_win(struct inbound_win *b, u8 *count, u64 size, | |
| u64 cpu_addr, u64 pci_offset) | |
| { | |
| b->size = size; | |
| b->cpu_addr = cpu_addr; | |
| b->pci_offset = pci_offset; | |
| (*count)++; | |
| } | |
| static int brcm_pcie_get_inbound_wins(struct brcm_pcie *pcie, | |
| struct inbound_win inbound_wins[]) | |
| { | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); | |
| u64 pci_offset, cpu_addr, size = 0, tot_size = 0; | |
| struct resource_entry *entry; | |
| struct device *dev = pcie->dev; | |
| u64 lowest_pcie_addr = ~(u64)0; | |
| int ret, i = 0; | |
| u8 n = 0; | |
| /* | |
| * The HW registers (and PCIe) use order-1 numbering for BARs. As such, | |
| * we have inbound_wins[0] unused and BAR1 starts at inbound_wins[1]. | |
| */ | |
| struct inbound_win *b_begin = &inbound_wins[1]; | |
| struct inbound_win *b = b_begin; | |
| /* | |
| * STB chips beside 7712 disable the first inbound window default. | |
| * Rather being mapped to system memory it is mapped to the | |
| * internal registers of the SoC. This feature is deprecated, has | |
| * security considerations, and is not implemented in our modern | |
| * SoCs. | |
| */ | |
| if (pcie->cfg->soc_base != BCM7712) | |
| add_inbound_win(b++, &n, 0, 0, 0); | |
| resource_list_for_each_entry(entry, &bridge->dma_ranges) { | |
| u64 pcie_start = entry->res->start - entry->offset; | |
| u64 cpu_start = entry->res->start; | |
| size = resource_size(entry->res); | |
| tot_size += size; | |
| if (pcie_start < lowest_pcie_addr) | |
| lowest_pcie_addr = pcie_start; | |
| /* | |
| * 7712 and newer chips may have many BARs, with each | |
| * offering a non-overlapping viewport to system memory. | |
| * That being said, each BARs size must still be a power of | |
| * two. | |
| */ | |
| if (pcie->cfg->soc_base == BCM7712) | |
| add_inbound_win(b++, &n, size, cpu_start, pcie_start); | |
| if (n > pcie->cfg->num_inbound_wins) | |
| break; | |
| } | |
| if (lowest_pcie_addr == ~(u64)0) { | |
| dev_err(dev, "DT node has no dma-ranges\n"); | |
| return -EINVAL; | |
| } | |
| /* | |
| * 7712 and newer chips do not have an internal memory mapping system | |
| * that enables multiple memory controllers. As such, it can return | |
| * now w/o doing special configuration. | |
| */ | |
| if (pcie->cfg->soc_base == BCM7712) | |
| return n; | |
| ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1, | |
| PCIE_BRCM_MAX_MEMC); | |
| if (ret <= 0) { | |
| /* Make an educated guess */ | |
| pcie->num_memc = 1; | |
| pcie->memc_size[0] = 1ULL << fls64(tot_size - 1); | |
| } else { | |
| pcie->num_memc = ret; | |
| } | |
| /* Each memc is viewed through a "port" that is a power of 2 */ | |
| for (i = 0, size = 0; i < pcie->num_memc; i++) | |
| size += pcie->memc_size[i]; | |
| /* Our HW mandates that the window size must be a power of 2 */ | |
| size = 1ULL << fls64(size - 1); | |
| /* | |
| * For STB chips, the BAR2 cpu_addr is hardwired to the start | |
| * of system memory, so we set it to 0. | |
| */ | |
| cpu_addr = 0; | |
| pci_offset = lowest_pcie_addr; | |
| /* | |
| * We validate the inbound memory view even though we should trust | |
| * whatever the device-tree provides. This is because of an HW issue on | |
| * early Raspberry Pi 4's revisions (bcm2711). It turns out its | |
| * firmware has to dynamically edit dma-ranges due to a bug on the | |
| * PCIe controller integration, which prohibits any access above the | |
| * lower 3GB of memory. Given this, we decided to keep the dma-ranges | |
| * in check, avoiding hard to debug device-tree related issues in the | |
| * future: | |
| * | |
| * The PCIe host controller by design must set the inbound viewport to | |
| * be a contiguous arrangement of all of the system's memory. In | |
| * addition, its size must be a power of two. To further complicate | |
| * matters, the viewport must start on a pcie-address that is aligned | |
| * on a multiple of its size. If a portion of the viewport does not | |
| * represent system memory -- e.g. 3GB of memory requires a 4GB | |
| * viewport -- we can map the outbound memory in or after 3GB and even | |
| * though the viewport will overlap the outbound memory the controller | |
| * will know to send outbound memory downstream and everything else | |
| * upstream. | |
| * | |
| * For example: | |
| * | |
| * - The best-case scenario, memory up to 3GB, is to place the inbound | |
| * region in the first 4GB of pcie-space, as some legacy devices can | |
| * only address 32bits. We would also like to put the MSI under 4GB | |
| * as well, since some devices require a 32bit MSI target address. | |
| * | |
| * - If the system memory is 4GB or larger we cannot start the inbound | |
| * region at location 0 (since we have to allow some space for | |
| * outbound memory @ 3GB). So instead it will start at the 1x | |
| * multiple of its size | |
| */ | |
| if (!size || (pci_offset & (size - 1)) || | |
| (pci_offset < SZ_4G && pci_offset > SZ_2G)) { | |
| dev_err(dev, "Invalid inbound_win2_offset/size: size 0x%llx, off 0x%llx\n", | |
| size, pci_offset); | |
| return -EINVAL; | |
| } | |
| /* Enable inbound window 2, the main inbound window for STB chips */ | |
| add_inbound_win(b++, &n, size, cpu_addr, pci_offset); | |
| /* | |
| * Disable inbound window 3. On some chips presents the same | |
| * window as #2 but the data appears in a settable endianness. | |
| */ | |
| add_inbound_win(b++, &n, 0, 0, 0); | |
| return n; | |
| } | |
| static u32 brcm_bar_reg_offset(int bar) | |
| { | |
| if (bar <= 3) | |
| return PCIE_MISC_RC_BAR1_CONFIG_LO + 8 * (bar - 1); | |
| else | |
| return PCIE_MISC_RC_BAR4_CONFIG_LO + 8 * (bar - 4); | |
| } | |
| static u32 brcm_ubus_reg_offset(int bar) | |
| { | |
| if (bar <= 3) | |
| return PCIE_MISC_UBUS_BAR1_CONFIG_REMAP + 8 * (bar - 1); | |
| else | |
| return PCIE_MISC_UBUS_BAR4_CONFIG_REMAP + 8 * (bar - 4); | |
| } | |
| static void set_inbound_win_registers(struct brcm_pcie *pcie, | |
| const struct inbound_win *inbound_wins, | |
| u8 num_inbound_wins) | |
| { | |
| void __iomem *base = pcie->base; | |
| int i; | |
| for (i = 1; i <= num_inbound_wins; i++) { | |
| u64 pci_offset = inbound_wins[i].pci_offset; | |
| u64 cpu_addr = inbound_wins[i].cpu_addr; | |
| u64 size = inbound_wins[i].size; | |
| u32 reg_offset = brcm_bar_reg_offset(i); | |
| u32 tmp = lower_32_bits(pci_offset); | |
| u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(size), | |
| PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK); | |
| /* Write low */ | |
| writel_relaxed(tmp, base + reg_offset); | |
| /* Write high */ | |
| writel_relaxed(upper_32_bits(pci_offset), base + reg_offset + 4); | |
| /* | |
| * Most STB chips: | |
| * Do nothing. | |
| * 7712: | |
| * All of their BARs need to be set. | |
| */ | |
| if (pcie->cfg->soc_base == BCM7712) { | |
| /* BUS remap register settings */ | |
| reg_offset = brcm_ubus_reg_offset(i); | |
| tmp = lower_32_bits(cpu_addr) & ~0xfff; | |
| tmp |= PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK; | |
| writel_relaxed(tmp, base + reg_offset); | |
| tmp = upper_32_bits(cpu_addr); | |
| writel_relaxed(tmp, base + reg_offset + 4); | |
| } | |
| } | |
| } | |
| static int brcm_pcie_setup(struct brcm_pcie *pcie) | |
| { | |
| struct inbound_win inbound_wins[PCIE_BRCM_MAX_INBOUND_WINS]; | |
| void __iomem *base = pcie->base; | |
| struct pci_host_bridge *bridge; | |
| struct resource_entry *entry; | |
| u32 tmp, burst, num_lanes, num_lanes_cap; | |
| u8 num_out_wins = 0; | |
| int num_inbound_wins = 0; | |
| int memc, ret; | |
| /* Reset the bridge */ | |
| ret = brcm_pcie_bridge_sw_init_set(pcie, 1); | |
| if (ret) | |
| return ret; | |
| /* Ensure that PERST# is asserted; some bootloaders may deassert it. */ | |
| if (pcie->cfg->soc_base == BCM2711) { | |
| ret = pcie->cfg->perst_set(pcie, 1); | |
| if (ret) { | |
| pcie->cfg->bridge_sw_init_set(pcie, 0); | |
| return ret; | |
| } | |
| } | |
| usleep_range(100, 200); | |
| /* Take the bridge out of reset */ | |
| ret = brcm_pcie_bridge_sw_init_set(pcie, 0); | |
| if (ret) | |
| return ret; | |
| tmp = readl(base + HARD_DEBUG(pcie)); | |
| if (is_bmips(pcie)) | |
| tmp &= ~PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK; | |
| else | |
| tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK; | |
| writel(tmp, base + HARD_DEBUG(pcie)); | |
| /* Wait for SerDes to be stable */ | |
| usleep_range(100, 200); | |
| /* | |
| * SCB_MAX_BURST_SIZE is a two bit field. For GENERIC chips it | |
| * is encoded as 0=128, 1=256, 2=512, 3=Rsvd, for BCM7278 it | |
| * is encoded as 0=Rsvd, 1=128, 2=256, 3=512. | |
| */ | |
| if (is_bmips(pcie)) | |
| burst = 0x1; /* 256 bytes */ | |
| else if (pcie->cfg->soc_base == BCM2711) | |
| burst = 0x0; /* 128 bytes */ | |
| else if (pcie->cfg->soc_base == BCM7278) | |
| burst = 0x3; /* 512 bytes */ | |
| else | |
| burst = 0x2; /* 512 bytes */ | |
| /* | |
| * Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN, | |
| * RCB_MPS_MODE, RCB_64B_MODE | |
| */ | |
| tmp = readl(base + PCIE_MISC_MISC_CTRL); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK); | |
| u32p_replace_bits(&tmp, burst, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_MPS_MODE_MASK); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK); | |
| writel(tmp, base + PCIE_MISC_MISC_CTRL); | |
| num_inbound_wins = brcm_pcie_get_inbound_wins(pcie, inbound_wins); | |
| if (num_inbound_wins < 0) | |
| return num_inbound_wins; | |
| set_inbound_win_registers(pcie, inbound_wins, num_inbound_wins); | |
| if (!brcm_pcie_rc_mode(pcie)) { | |
| dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n"); | |
| return -EINVAL; | |
| } | |
| tmp = readl(base + PCIE_MISC_MISC_CTRL); | |
| for (memc = 0; memc < pcie->num_memc; memc++) { | |
| u32 scb_size_val = ilog2(pcie->memc_size[memc]) - 15; | |
| if (memc == 0) | |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(0)); | |
| else if (memc == 1) | |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(1)); | |
| else if (memc == 2) | |
| u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(2)); | |
| } | |
| writel(tmp, base + PCIE_MISC_MISC_CTRL); | |
| /* | |
| * We ideally want the MSI target address to be located in the 32bit | |
| * addressable memory area. Some devices might depend on it. This is | |
| * possible either when the inbound window is located above the lower | |
| * 4GB or when the inbound area is smaller than 4GB (taking into | |
| * account the rounding-up we're forced to perform). | |
| */ | |
| if (inbound_wins[2].pci_offset >= SZ_4G || | |
| (inbound_wins[2].size + inbound_wins[2].pci_offset) < SZ_4G) | |
| pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_LT_4GB; | |
| else | |
| pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_GT_4GB; | |
| /* Don't advertise L0s capability if 'aspm-no-l0s' */ | |
| tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); | |
| if (of_property_read_bool(pcie->np, "aspm-no-l0s")) | |
| tmp &= ~PCI_EXP_LNKCAP_ASPM_L0S; | |
| writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); | |
| /* 'tmp' still holds the contents of PRIV1_LINK_CAPABILITY */ | |
| num_lanes_cap = u32_get_bits(tmp, PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_MAX_LINK_WIDTH_MASK); | |
| num_lanes = 0; | |
| /* | |
| * Use hardware negotiated Max Link Width value by default. If the | |
| * "num-lanes" DT property is present, assume that the chip's default | |
| * link width capability information is incorrect/undesired and use the | |
| * specified value instead. | |
| */ | |
| if (!of_property_read_u32(pcie->np, "num-lanes", &num_lanes) && | |
| num_lanes && num_lanes <= 4 && num_lanes_cap != num_lanes) { | |
| u32p_replace_bits(&tmp, num_lanes, | |
| PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_MAX_LINK_WIDTH_MASK); | |
| writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY); | |
| tmp = readl(base + PCIE_RC_PL_REG_PHY_CTL_1); | |
| u32p_replace_bits(&tmp, 1, | |
| PCIE_RC_PL_REG_PHY_CTL_1_REG_P2_POWERDOWN_ENA_NOSYNC_MASK); | |
| writel(tmp, base + PCIE_RC_PL_REG_PHY_CTL_1); | |
| } | |
| /* | |
| * For config space accesses on the RC, show the right class for | |
| * a PCIe-PCIe bridge (the default setting is to be EP mode). | |
| */ | |
| tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3); | |
| u32p_replace_bits(&tmp, 0x060400, | |
| PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK); | |
| writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3); | |
| bridge = pci_host_bridge_from_priv(pcie); | |
| resource_list_for_each_entry(entry, &bridge->windows) { | |
| struct resource *res = entry->res; | |
| if (resource_type(res) != IORESOURCE_MEM) | |
| continue; | |
| if (num_out_wins >= BRCM_NUM_PCIE_OUT_WINS) { | |
| dev_err(pcie->dev, "too many outbound wins\n"); | |
| return -EINVAL; | |
| } | |
| if (is_bmips(pcie)) { | |
| u64 start = res->start; | |
| unsigned int j, nwins = resource_size(res) / SZ_128M; | |
| /* bmips PCIe outbound windows have a 128MB max size */ | |
| if (nwins > BRCM_NUM_PCIE_OUT_WINS) | |
| nwins = BRCM_NUM_PCIE_OUT_WINS; | |
| for (j = 0; j < nwins; j++, start += SZ_128M) | |
| brcm_pcie_set_outbound_win(pcie, j, start, | |
| start - entry->offset, | |
| SZ_128M); | |
| break; | |
| } | |
| brcm_pcie_set_outbound_win(pcie, num_out_wins, res->start, | |
| res->start - entry->offset, | |
| resource_size(res)); | |
| num_out_wins++; | |
| } | |
| /* PCIe->SCB endian mode for inbound window */ | |
| tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); | |
| u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPECIFIC_REG1_LITTLE_ENDIAN, | |
| PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK); | |
| writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); | |
| if (pcie->cfg->post_setup) { | |
| ret = pcie->cfg->post_setup(pcie); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| /* | |
| * This extends the timeout period for an access to an internal bus. This | |
| * access timeout may occur during L1SS sleep periods, even without the | |
| * presence of a PCIe access. | |
| */ | |
| static void brcm_extend_rbus_timeout(struct brcm_pcie *pcie) | |
| { | |
| /* TIMEOUT register is two registers before RGR1_SW_INIT_1 */ | |
| const unsigned int REG_OFFSET = PCIE_RGR1_SW_INIT_1(pcie) - 8; | |
| u32 timeout_us = 4000000; /* 4 seconds, our setting for L1SS */ | |
| /* 7712 does not have this (RGR1) timer */ | |
| if (pcie->cfg->soc_base == BCM7712) | |
| return; | |
| /* Each unit in timeout register is 1/216,000,000 seconds */ | |
| writel(216 * timeout_us, pcie->base + REG_OFFSET); | |
| } | |
| static void brcm_config_clkreq(struct brcm_pcie *pcie) | |
| { | |
| static const char err_msg[] = "invalid 'brcm,clkreq-mode' DT string\n"; | |
| const char *mode = "default"; | |
| u32 clkreq_cntl; | |
| int ret, tmp; | |
| ret = of_property_read_string(pcie->np, "brcm,clkreq-mode", &mode); | |
| if (ret && ret != -EINVAL) { | |
| dev_err(pcie->dev, err_msg); | |
| mode = "safe"; | |
| } | |
| /* Start out assuming safe mode (both mode bits cleared) */ | |
| clkreq_cntl = readl(pcie->base + HARD_DEBUG(pcie)); | |
| clkreq_cntl &= ~PCIE_CLKREQ_MASK; | |
| if (strcmp(mode, "no-l1ss") == 0) { | |
| /* | |
| * "no-l1ss" -- Provides Clock Power Management, L0s, and | |
| * L1, but cannot provide L1 substate (L1SS) power | |
| * savings. If the downstream device connected to the RC is | |
| * L1SS capable AND the OS enables L1SS, all PCIe traffic | |
| * may abruptly halt, potentially hanging the system. | |
| */ | |
| clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; | |
| /* | |
| * We want to un-advertise L1 substates because if the OS | |
| * tries to configure the controller into using L1 substate | |
| * power savings it may fail or hang when the RC HW is in | |
| * "no-l1ss" mode. | |
| */ | |
| tmp = readl(pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP); | |
| u32p_replace_bits(&tmp, 2, PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK); | |
| writel(tmp, pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP); | |
| } else if (strcmp(mode, "default") == 0) { | |
| /* | |
| * "default" -- Provides L0s, L1, and L1SS, but not | |
| * compliant to provide Clock Power Management; | |
| * specifically, may not be able to meet the Tclron max | |
| * timing of 400ns as specified in "Dynamic Clock Control", | |
| * section 3.2.5.2.2 of the PCIe spec. This situation is | |
| * atypical and should happen only with older devices. | |
| */ | |
| clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK; | |
| brcm_extend_rbus_timeout(pcie); | |
| } else { | |
| /* | |
| * "safe" -- No power savings; refclk is driven by RC | |
| * unconditionally. | |
| */ | |
| if (strcmp(mode, "safe") != 0) | |
| dev_err(pcie->dev, err_msg); | |
| mode = "safe"; | |
| } | |
| writel(clkreq_cntl, pcie->base + HARD_DEBUG(pcie)); | |
| dev_info(pcie->dev, "clkreq-mode set to %s\n", mode); | |
| } | |
| static int brcm_pcie_start_link(struct brcm_pcie *pcie) | |
| { | |
| struct device *dev = pcie->dev; | |
| void __iomem *base = pcie->base; | |
| u16 nlw, cls, lnksta; | |
| bool ssc_good = false; | |
| int ret, i; | |
| /* Limit the generation if specified */ | |
| if (pcie->gen) | |
| brcm_pcie_set_gen(pcie, pcie->gen); | |
| /* Unassert the fundamental reset */ | |
| ret = pcie->cfg->perst_set(pcie, 0); | |
| if (ret) | |
| return ret; | |
| msleep(PCIE_RESET_CONFIG_WAIT_MS); | |
| /* | |
| * Give the RC/EP even more time to wake up, before trying to | |
| * configure RC. Intermittently check status for link-up, up to a | |
| * total of 100ms. | |
| */ | |
| for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5) | |
| msleep(5); | |
| if (!brcm_pcie_link_up(pcie)) { | |
| dev_err(dev, "link down\n"); | |
| return -ENODEV; | |
| } | |
| brcm_config_clkreq(pcie); | |
| if (pcie->ssc) { | |
| ret = brcm_pcie_set_ssc(pcie); | |
| if (ret == 0) | |
| ssc_good = true; | |
| else | |
| dev_err(dev, "failed attempt to enter ssc mode\n"); | |
| } | |
| lnksta = readw(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKSTA); | |
| cls = FIELD_GET(PCI_EXP_LNKSTA_CLS, lnksta); | |
| nlw = FIELD_GET(PCI_EXP_LNKSTA_NLW, lnksta); | |
| dev_info(dev, "link up, %s x%u %s\n", | |
| pci_speed_string(pcie_get_link_speed(cls)), nlw, | |
| ssc_good ? "(SSC)" : "(!SSC)"); | |
| return 0; | |
| } | |
| static const char * const supplies[] = { | |
| "vpcie3v3", | |
| "vpcie3v3aux", | |
| "vpcie12v", | |
| }; | |
| static void *alloc_subdev_regulators(struct device *dev) | |
| { | |
| const size_t size = sizeof(struct subdev_regulators) + | |
| sizeof(struct regulator_bulk_data) * ARRAY_SIZE(supplies); | |
| struct subdev_regulators *sr; | |
| int i; | |
| sr = devm_kzalloc(dev, size, GFP_KERNEL); | |
| if (sr) { | |
| sr->num_supplies = ARRAY_SIZE(supplies); | |
| for (i = 0; i < ARRAY_SIZE(supplies); i++) | |
| sr->supplies[i].supply = supplies[i]; | |
| } | |
| return sr; | |
| } | |
| static int brcm_pcie_add_bus(struct pci_bus *bus) | |
| { | |
| struct brcm_pcie *pcie = bus->sysdata; | |
| struct device *dev = &bus->dev; | |
| struct subdev_regulators *sr; | |
| int ret; | |
| if (!bus->parent || !pci_is_root_bus(bus->parent)) | |
| return 0; | |
| if (dev->of_node) { | |
| sr = alloc_subdev_regulators(dev); | |
| if (!sr) { | |
| dev_info(dev, "Can't allocate regulators for downstream device\n"); | |
| goto no_regulators; | |
| } | |
| pcie->sr = sr; | |
| ret = regulator_bulk_get(dev, sr->num_supplies, sr->supplies); | |
| if (ret) { | |
| dev_info(dev, "Did not get regulators, err=%d\n", ret); | |
| pcie->sr = NULL; | |
| goto no_regulators; | |
| } | |
| ret = regulator_bulk_enable(sr->num_supplies, sr->supplies); | |
| if (ret) { | |
| dev_err(dev, "Can't enable regulators for downstream device\n"); | |
| regulator_bulk_free(sr->num_supplies, sr->supplies); | |
| pcie->sr = NULL; | |
| } | |
| } | |
| no_regulators: | |
| brcm_pcie_start_link(pcie); | |
| return 0; | |
| } | |
| static void brcm_pcie_remove_bus(struct pci_bus *bus) | |
| { | |
| struct brcm_pcie *pcie = bus->sysdata; | |
| struct subdev_regulators *sr = pcie->sr; | |
| struct device *dev = &bus->dev; | |
| if (!sr || !bus->parent || !pci_is_root_bus(bus->parent)) | |
| return; | |
| if (regulator_bulk_disable(sr->num_supplies, sr->supplies)) | |
| dev_err(dev, "Failed to disable regulators for downstream device\n"); | |
| regulator_bulk_free(sr->num_supplies, sr->supplies); | |
| pcie->sr = NULL; | |
| } | |
| /* L23 is a low-power PCIe link state */ | |
| static void brcm_pcie_enter_l23(struct brcm_pcie *pcie) | |
| { | |
| void __iomem *base = pcie->base; | |
| int l23, i; | |
| u32 tmp; | |
| /* Assert request for L23 */ | |
| tmp = readl(base + PCIE_MISC_PCIE_CTRL); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK); | |
| writel(tmp, base + PCIE_MISC_PCIE_CTRL); | |
| /* Wait up to 36 msec for L23 */ | |
| tmp = readl(base + PCIE_MISC_PCIE_STATUS); | |
| l23 = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK, tmp); | |
| for (i = 0; i < 15 && !l23; i++) { | |
| usleep_range(2000, 2400); | |
| tmp = readl(base + PCIE_MISC_PCIE_STATUS); | |
| l23 = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK, | |
| tmp); | |
| } | |
| if (!l23) | |
| dev_err(pcie->dev, "failed to enter low-power link state\n"); | |
| } | |
| static int brcm_phy_cntl(struct brcm_pcie *pcie, const int start) | |
| { | |
| static const u32 shifts[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = { | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT, | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT, | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT,}; | |
| static const u32 masks[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = { | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK, | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK, | |
| PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK,}; | |
| const int beg = start ? 0 : PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS - 1; | |
| const int end = start ? PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS : -1; | |
| u32 tmp, combined_mask = 0; | |
| u32 val; | |
| void __iomem *base = pcie->base; | |
| int i, ret; | |
| for (i = beg; i != end; start ? i++ : i--) { | |
| val = start ? BIT_MASK(shifts[i]) : 0; | |
| tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL); | |
| tmp = (tmp & ~masks[i]) | (val & masks[i]); | |
| writel(tmp, base + PCIE_DVT_PMU_PCIE_PHY_CTRL); | |
| usleep_range(50, 200); | |
| combined_mask |= masks[i]; | |
| } | |
| tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL); | |
| val = start ? combined_mask : 0; | |
| ret = (tmp & combined_mask) == val ? 0 : -EIO; | |
| if (ret) | |
| dev_err(pcie->dev, "failed to %s phy\n", (start ? "start" : "stop")); | |
| return ret; | |
| } | |
| static inline int brcm_phy_start(struct brcm_pcie *pcie) | |
| { | |
| return pcie->cfg->has_phy ? brcm_phy_cntl(pcie, 1) : 0; | |
| } | |
| static inline int brcm_phy_stop(struct brcm_pcie *pcie) | |
| { | |
| return pcie->cfg->has_phy ? brcm_phy_cntl(pcie, 0) : 0; | |
| } | |
| static int brcm_pcie_turn_off(struct brcm_pcie *pcie) | |
| { | |
| void __iomem *base = pcie->base; | |
| int tmp, ret; | |
| if (brcm_pcie_link_up(pcie)) | |
| brcm_pcie_enter_l23(pcie); | |
| /* Assert fundamental reset */ | |
| ret = pcie->cfg->perst_set(pcie, 1); | |
| if (ret) | |
| return ret; | |
| /* Deassert request for L23 in case it was asserted */ | |
| tmp = readl(base + PCIE_MISC_PCIE_CTRL); | |
| u32p_replace_bits(&tmp, 0, PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK); | |
| writel(tmp, base + PCIE_MISC_PCIE_CTRL); | |
| /* Turn off SerDes */ | |
| tmp = readl(base + HARD_DEBUG(pcie)); | |
| u32p_replace_bits(&tmp, 1, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK); | |
| writel(tmp, base + HARD_DEBUG(pcie)); | |
| if (!(pcie->cfg->quirks & CFG_QUIRK_AVOID_BRIDGE_SHUTDOWN)) | |
| /* Shutdown PCIe bridge */ | |
| ret = brcm_pcie_bridge_sw_init_set(pcie, 1); | |
| return ret; | |
| } | |
| static int pci_dev_may_wakeup(struct pci_dev *dev, void *data) | |
| { | |
| bool *ret = data; | |
| if (device_may_wakeup(&dev->dev)) { | |
| *ret = true; | |
| dev_info(&dev->dev, "Possible wake-up device; regulators will not be disabled\n"); | |
| } | |
| return (int) *ret; | |
| } | |
| static int brcm_pcie_suspend_noirq(struct device *dev) | |
| { | |
| struct brcm_pcie *pcie = dev_get_drvdata(dev); | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); | |
| int ret, rret; | |
| ret = brcm_pcie_turn_off(pcie); | |
| if (ret) | |
| return ret; | |
| /* | |
| * If brcm_phy_stop() returns an error, just dev_err(). If we | |
| * return the error it will cause the suspend to fail and this is a | |
| * forgivable offense that will probably be erased on resume. | |
| */ | |
| if (brcm_phy_stop(pcie)) | |
| dev_err(dev, "Could not stop phy for suspend\n"); | |
| ret = reset_control_rearm(pcie->rescal); | |
| if (ret) { | |
| dev_err(dev, "Could not rearm rescal reset\n"); | |
| return ret; | |
| } | |
| if (pcie->sr) { | |
| /* | |
| * Now turn off the regulators, but if at least one | |
| * downstream device is enabled as a wake-up source, do not | |
| * turn off regulators. | |
| */ | |
| pcie->ep_wakeup_capable = false; | |
| pci_walk_bus(bridge->bus, pci_dev_may_wakeup, | |
| &pcie->ep_wakeup_capable); | |
| if (!pcie->ep_wakeup_capable) { | |
| ret = regulator_bulk_disable(pcie->sr->num_supplies, | |
| pcie->sr->supplies); | |
| if (ret) { | |
| dev_err(dev, "Could not turn off regulators\n"); | |
| rret = reset_control_reset(pcie->rescal); | |
| if (rret) | |
| dev_err(dev, "failed to reset 'rascal' controller ret=%d\n", | |
| rret); | |
| return ret; | |
| } | |
| } | |
| } | |
| clk_disable_unprepare(pcie->clk); | |
| return 0; | |
| } | |
| static int brcm_pcie_resume_noirq(struct device *dev) | |
| { | |
| struct brcm_pcie *pcie = dev_get_drvdata(dev); | |
| void __iomem *base; | |
| u32 tmp; | |
| int ret, rret; | |
| base = pcie->base; | |
| ret = clk_prepare_enable(pcie->clk); | |
| if (ret) | |
| return ret; | |
| ret = reset_control_reset(pcie->rescal); | |
| if (ret) | |
| goto err_disable_clk; | |
| ret = brcm_phy_start(pcie); | |
| if (ret) | |
| goto err_reset; | |
| /* Take bridge out of reset so we can access the SERDES reg */ | |
| ret = brcm_pcie_bridge_sw_init_set(pcie, 0); | |
| if (ret) | |
| goto err_reset; | |
| /* SERDES_IDDQ = 0 */ | |
| tmp = readl(base + HARD_DEBUG(pcie)); | |
| u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK); | |
| writel(tmp, base + HARD_DEBUG(pcie)); | |
| /* wait for serdes to be stable */ | |
| udelay(100); | |
| ret = brcm_pcie_setup(pcie); | |
| if (ret) | |
| goto err_reset; | |
| if (pcie->sr) { | |
| if (pcie->ep_wakeup_capable) { | |
| /* | |
| * We are resuming from a suspend. In the suspend we | |
| * did not disable the power supplies, so there is | |
| * no need to enable them (and falsely increase their | |
| * usage count). | |
| */ | |
| pcie->ep_wakeup_capable = false; | |
| } else { | |
| ret = regulator_bulk_enable(pcie->sr->num_supplies, | |
| pcie->sr->supplies); | |
| if (ret) { | |
| dev_err(dev, "Could not turn on regulators\n"); | |
| goto err_reset; | |
| } | |
| } | |
| } | |
| ret = brcm_pcie_start_link(pcie); | |
| if (ret) | |
| goto err_regulator; | |
| if (pcie->msi) | |
| brcm_msi_set_regs(pcie->msi); | |
| return 0; | |
| err_regulator: | |
| if (pcie->sr) | |
| regulator_bulk_disable(pcie->sr->num_supplies, pcie->sr->supplies); | |
| err_reset: | |
| rret = reset_control_rearm(pcie->rescal); | |
| if (rret) | |
| dev_err(pcie->dev, "failed to rearm 'rescal' reset, err=%d\n", rret); | |
| err_disable_clk: | |
| clk_disable_unprepare(pcie->clk); | |
| return ret; | |
| } | |
| /* Dump out PCIe errors on die or panic */ | |
| static int brcm_pcie_dump_err(struct brcm_pcie *pcie, | |
| const char *type) | |
| { | |
| void __iomem *base = pcie->base; | |
| int i, is_cfg_err, is_mem_err, lanes; | |
| const char *width_str, *direction_str; | |
| u32 info, cfg_addr, cfg_cause, mem_cause, lo, hi; | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); | |
| unsigned long flags; | |
| char lanes_str[9]; | |
| spin_lock_irqsave(&pcie->bridge_lock, flags); | |
| /* Don't access registers when the bridge is off */ | |
| if (pcie->bridge_in_reset || readl(base + PCIE_OUTB_ERR_VALID) == 0) { | |
| spin_unlock_irqrestore(&pcie->bridge_lock, flags); | |
| return NOTIFY_DONE; | |
| } | |
| /* Read all necessary registers so we can release the spinlock ASAP */ | |
| info = readl(base + PCIE_OUTB_ERR_ACC_INFO); | |
| is_cfg_err = !!(info & PCIE_OUTB_ERR_ACC_INFO_CFG_ERR); | |
| is_mem_err = !!(info & PCIE_OUTB_ERR_ACC_INFO_MEM_ERR); | |
| if (is_cfg_err) { | |
| cfg_addr = readl(base + PCIE_OUTB_ERR_ACC_ADDR); | |
| cfg_cause = readl(base + PCIE_OUTB_ERR_CFG_CAUSE); | |
| } | |
| if (is_mem_err) { | |
| mem_cause = readl(base + PCIE_OUTB_ERR_MEM_CAUSE); | |
| lo = readl(base + PCIE_OUTB_ERR_MEM_ADDR_LO); | |
| hi = readl(base + PCIE_OUTB_ERR_MEM_ADDR_HI); | |
| } | |
| /* We've got all of the info, clear the error */ | |
| writel(1, base + PCIE_OUTB_ERR_CLEAR); | |
| spin_unlock_irqrestore(&pcie->bridge_lock, flags); | |
| dev_err(pcie->dev, "reporting PCIe info which may be related to %s error\n", | |
| type); | |
| width_str = (info & PCIE_OUTB_ERR_ACC_INFO_TYPE_64) ? "64bit" : "32bit"; | |
| direction_str = str_read_write(!(info & PCIE_OUTB_ERR_ACC_INFO_DIR_WRITE)); | |
| lanes = FIELD_GET(PCIE_OUTB_ERR_ACC_INFO_BYTE_LANES, info); | |
| for (i = 0, lanes_str[8] = 0; i < 8; i++) | |
| lanes_str[i] = (lanes & (1 << i)) ? '1' : '0'; | |
| if (is_cfg_err) { | |
| int bus = FIELD_GET(PCIE_OUTB_ERR_ACC_ADDR_BUS, cfg_addr); | |
| int dev = FIELD_GET(PCIE_OUTB_ERR_ACC_ADDR_DEV, cfg_addr); | |
| int func = FIELD_GET(PCIE_OUTB_ERR_ACC_ADDR_FUNC, cfg_addr); | |
| int reg = FIELD_GET(PCIE_OUTB_ERR_ACC_ADDR_REG, cfg_addr); | |
| dev_err(pcie->dev, "Error: CFG Acc, %s, %s (%04x:%02x:%02x.%d) reg=0x%x, lanes=%s\n", | |
| width_str, direction_str, bridge->domain_nr, bus, dev, | |
| func, reg, lanes_str); | |
| dev_err(pcie->dev, " Type: TO=%d Abt=%d UnsupReq=%d AccTO=%d AccDsbld=%d Acc64bit=%d\n", | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_TIMEOUT), | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_ABORT), | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_UNSUPP_REQ), | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_ACC_TIMEOUT), | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_ACC_DISABLED), | |
| !!(cfg_cause & PCIE_OUTB_ERR_CFG_CAUSE_ACC_64BIT)); | |
| } | |
| if (is_mem_err) { | |
| u64 addr = ((u64)hi << 32) | (u64)lo; | |
| dev_err(pcie->dev, "Error: Mem Acc, %s, %s, @0x%llx, lanes=%s\n", | |
| width_str, direction_str, addr, lanes_str); | |
| dev_err(pcie->dev, " Type: TO=%d Abt=%d UnsupReq=%d AccDsble=%d BadAddr=%d\n", | |
| !!(mem_cause & PCIE_OUTB_ERR_MEM_CAUSE_TIMEOUT), | |
| !!(mem_cause & PCIE_OUTB_ERR_MEM_CAUSE_ABORT), | |
| !!(mem_cause & PCIE_OUTB_ERR_MEM_CAUSE_UNSUPP_REQ), | |
| !!(mem_cause & PCIE_OUTB_ERR_MEM_CAUSE_ACC_DISABLED), | |
| !!(mem_cause & PCIE_OUTB_ERR_MEM_CAUSE_BAD_ADDR)); | |
| } | |
| return NOTIFY_DONE; | |
| } | |
| static int brcm_pcie_die_notify_cb(struct notifier_block *self, | |
| unsigned long v, void *p) | |
| { | |
| struct brcm_pcie *pcie = | |
| container_of(self, struct brcm_pcie, die_notifier); | |
| return brcm_pcie_dump_err(pcie, "Die"); | |
| } | |
| static int brcm_pcie_panic_notify_cb(struct notifier_block *self, | |
| unsigned long v, void *p) | |
| { | |
| struct brcm_pcie *pcie = | |
| container_of(self, struct brcm_pcie, panic_notifier); | |
| return brcm_pcie_dump_err(pcie, "Panic"); | |
| } | |
| static void brcm_register_die_notifiers(struct brcm_pcie *pcie) | |
| { | |
| pcie->panic_notifier.notifier_call = brcm_pcie_panic_notify_cb; | |
| atomic_notifier_chain_register(&panic_notifier_list, | |
| &pcie->panic_notifier); | |
| pcie->die_notifier.notifier_call = brcm_pcie_die_notify_cb; | |
| register_die_notifier(&pcie->die_notifier); | |
| } | |
| static void brcm_unregister_die_notifiers(struct brcm_pcie *pcie) | |
| { | |
| unregister_die_notifier(&pcie->die_notifier); | |
| atomic_notifier_chain_unregister(&panic_notifier_list, | |
| &pcie->panic_notifier); | |
| } | |
| static void __brcm_pcie_remove(struct brcm_pcie *pcie) | |
| { | |
| brcm_msi_remove(pcie); | |
| brcm_pcie_turn_off(pcie); | |
| if (brcm_phy_stop(pcie)) | |
| dev_err(pcie->dev, "Could not stop phy\n"); | |
| if (reset_control_rearm(pcie->rescal)) | |
| dev_err(pcie->dev, "Could not rearm rescal reset\n"); | |
| clk_disable_unprepare(pcie->clk); | |
| } | |
| static void brcm_pcie_remove(struct platform_device *pdev) | |
| { | |
| struct brcm_pcie *pcie = platform_get_drvdata(pdev); | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); | |
| pci_lock_rescan_remove(); | |
| pci_stop_root_bus(bridge->bus); | |
| pci_remove_root_bus(bridge->bus); | |
| pci_unlock_rescan_remove(); | |
| if (pcie->cfg->has_err_report) | |
| brcm_unregister_die_notifiers(pcie); | |
| __brcm_pcie_remove(pcie); | |
| } | |
| static const int pcie_offsets[] = { | |
| [RGR1_SW_INIT_1] = 0x9210, | |
| [EXT_CFG_INDEX] = 0x9000, | |
| [EXT_CFG_DATA] = 0x8000, | |
| [PCIE_HARD_DEBUG] = 0x4204, | |
| [PCIE_INTR2_CPU_BASE] = 0x4300, | |
| }; | |
| static const int pcie_offsets_bcm7278[] = { | |
| [RGR1_SW_INIT_1] = 0xc010, | |
| [EXT_CFG_INDEX] = 0x9000, | |
| [EXT_CFG_DATA] = 0x8000, | |
| [PCIE_HARD_DEBUG] = 0x4204, | |
| [PCIE_INTR2_CPU_BASE] = 0x4300, | |
| }; | |
| static const int pcie_offsets_bcm7425[] = { | |
| [RGR1_SW_INIT_1] = 0x8010, | |
| [EXT_CFG_INDEX] = 0x8300, | |
| [EXT_CFG_DATA] = 0x8304, | |
| [PCIE_HARD_DEBUG] = 0x4204, | |
| [PCIE_INTR2_CPU_BASE] = 0x4300, | |
| }; | |
| static const int pcie_offsets_bcm7712[] = { | |
| [RGR1_SW_INIT_1] = 0x9210, | |
| [EXT_CFG_INDEX] = 0x9000, | |
| [EXT_CFG_DATA] = 0x8000, | |
| [PCIE_HARD_DEBUG] = 0x4304, | |
| [PCIE_INTR2_CPU_BASE] = 0x4400, | |
| }; | |
| static const struct pcie_cfg_data generic_cfg = { | |
| .offsets = pcie_offsets, | |
| .soc_base = GENERIC, | |
| .perst_set = brcm_pcie_perst_set_generic, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm2711_cfg = { | |
| .offsets = pcie_offsets, | |
| .soc_base = BCM2711, | |
| .perst_set = brcm_pcie_perst_set_generic, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm2712_cfg = { | |
| .offsets = pcie_offsets_bcm7712, | |
| .soc_base = BCM7712, | |
| .perst_set = brcm_pcie_perst_set_7278, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .post_setup = brcm_pcie_post_setup_bcm2712, | |
| .quirks = CFG_QUIRK_AVOID_BRIDGE_SHUTDOWN, | |
| .num_inbound_wins = 10, | |
| }; | |
| static const struct pcie_cfg_data bcm4908_cfg = { | |
| .offsets = pcie_offsets, | |
| .soc_base = BCM4908, | |
| .perst_set = brcm_pcie_perst_set_4908, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm7278_cfg = { | |
| .offsets = pcie_offsets_bcm7278, | |
| .soc_base = BCM7278, | |
| .perst_set = brcm_pcie_perst_set_7278, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm7425_cfg = { | |
| .offsets = pcie_offsets_bcm7425, | |
| .soc_base = BCM7425, | |
| .perst_set = brcm_pcie_perst_set_generic, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm7435_cfg = { | |
| .offsets = pcie_offsets, | |
| .soc_base = BCM7435, | |
| .perst_set = brcm_pcie_perst_set_generic, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .num_inbound_wins = 3, | |
| }; | |
| static const struct pcie_cfg_data bcm7216_cfg = { | |
| .offsets = pcie_offsets_bcm7278, | |
| .soc_base = BCM7278, | |
| .perst_set = brcm_pcie_perst_set_7278, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278, | |
| .has_phy = true, | |
| .num_inbound_wins = 3, | |
| .has_err_report = true, | |
| }; | |
| static const struct pcie_cfg_data bcm7712_cfg = { | |
| .offsets = pcie_offsets_bcm7712, | |
| .perst_set = brcm_pcie_perst_set_7278, | |
| .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic, | |
| .soc_base = BCM7712, | |
| .num_inbound_wins = 10, | |
| }; | |
| static const struct of_device_id brcm_pcie_match[] = { | |
| { .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg }, | |
| { .compatible = "brcm,bcm2712-pcie", .data = &bcm2712_cfg }, | |
| { .compatible = "brcm,bcm4908-pcie", .data = &bcm4908_cfg }, | |
| { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg }, | |
| { .compatible = "brcm,bcm7216-pcie", .data = &bcm7216_cfg }, | |
| { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg }, | |
| { .compatible = "brcm,bcm7425-pcie", .data = &bcm7425_cfg }, | |
| { .compatible = "brcm,bcm7435-pcie", .data = &bcm7435_cfg }, | |
| { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg }, | |
| { .compatible = "brcm,bcm7712-pcie", .data = &bcm7712_cfg }, | |
| {}, | |
| }; | |
| static struct pci_ops brcm_pcie_ops = { | |
| .map_bus = brcm_pcie_map_bus, | |
| .read = pci_generic_config_read, | |
| .write = pci_generic_config_write, | |
| .add_bus = brcm_pcie_add_bus, | |
| .remove_bus = brcm_pcie_remove_bus, | |
| }; | |
| static struct pci_ops brcm7425_pcie_ops = { | |
| .map_bus = brcm7425_pcie_map_bus, | |
| .read = pci_generic_config_read32, | |
| .write = pci_generic_config_write32, | |
| .add_bus = brcm_pcie_add_bus, | |
| .remove_bus = brcm_pcie_remove_bus, | |
| }; | |
| static int brcm_pcie_probe(struct platform_device *pdev) | |
| { | |
| struct device_node *np = pdev->dev.of_node; | |
| struct pci_host_bridge *bridge; | |
| const struct pcie_cfg_data *data; | |
| struct brcm_pcie *pcie; | |
| int ret; | |
| bridge = devm_pci_alloc_host_bridge(&pdev->dev, sizeof(*pcie)); | |
| if (!bridge) | |
| return -ENOMEM; | |
| data = of_device_get_match_data(&pdev->dev); | |
| if (!data) { | |
| pr_err("failed to look up compatible string\n"); | |
| return -EINVAL; | |
| } | |
| pcie = pci_host_bridge_priv(bridge); | |
| pcie->dev = &pdev->dev; | |
| pcie->np = np; | |
| pcie->cfg = data; | |
| pcie->base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(pcie->base)) | |
| return PTR_ERR(pcie->base); | |
| pcie->clk = devm_clk_get_optional(&pdev->dev, "sw_pcie"); | |
| if (IS_ERR(pcie->clk)) | |
| return PTR_ERR(pcie->clk); | |
| ret = of_pci_get_max_link_speed(np); | |
| if (ret < 0 || ret > 3) | |
| pcie->gen = 0; | |
| else | |
| pcie->gen = ret; | |
| pcie->ssc = of_property_read_bool(np, "brcm,enable-ssc"); | |
| pcie->rescal = devm_reset_control_get_optional_shared(&pdev->dev, "rescal"); | |
| if (IS_ERR(pcie->rescal)) | |
| return PTR_ERR(pcie->rescal); | |
| pcie->perst_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "perst"); | |
| if (IS_ERR(pcie->perst_reset)) | |
| return PTR_ERR(pcie->perst_reset); | |
| pcie->bridge_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "bridge"); | |
| if (IS_ERR(pcie->bridge_reset)) | |
| return PTR_ERR(pcie->bridge_reset); | |
| pcie->swinit_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "swinit"); | |
| if (IS_ERR(pcie->swinit_reset)) | |
| return PTR_ERR(pcie->swinit_reset); | |
| ret = clk_prepare_enable(pcie->clk); | |
| if (ret) | |
| return dev_err_probe(&pdev->dev, ret, "could not enable clock\n"); | |
| ret = brcm_pcie_bridge_sw_init_set(pcie, 0); | |
| if (ret) | |
| return dev_err_probe(&pdev->dev, ret, | |
| "could not de-assert bridge reset\n"); | |
| if (pcie->swinit_reset) { | |
| ret = reset_control_assert(pcie->swinit_reset); | |
| if (ret) { | |
| clk_disable_unprepare(pcie->clk); | |
| return dev_err_probe(&pdev->dev, ret, | |
| "could not assert reset 'swinit'\n"); | |
| } | |
| /* HW team recommends 1us for proper sync and propagation of reset */ | |
| udelay(1); | |
| ret = reset_control_deassert(pcie->swinit_reset); | |
| if (ret) { | |
| clk_disable_unprepare(pcie->clk); | |
| return dev_err_probe(&pdev->dev, ret, | |
| "could not de-assert reset 'swinit'\n"); | |
| } | |
| } | |
| ret = reset_control_reset(pcie->rescal); | |
| if (ret) { | |
| clk_disable_unprepare(pcie->clk); | |
| return dev_err_probe(&pdev->dev, ret, "failed to deassert 'rescal'\n"); | |
| } | |
| ret = brcm_phy_start(pcie); | |
| if (ret) { | |
| reset_control_rearm(pcie->rescal); | |
| clk_disable_unprepare(pcie->clk); | |
| return ret; | |
| } | |
| ret = brcm_pcie_setup(pcie); | |
| if (ret) | |
| goto fail; | |
| pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION); | |
| if (pcie->cfg->soc_base == BCM4908 && | |
| pcie->hw_rev >= BRCM_PCIE_HW_REV_3_20) { | |
| dev_err(pcie->dev, "hardware revision with unsupported PERST# setup\n"); | |
| ret = -ENODEV; | |
| goto fail; | |
| } | |
| if (pci_msi_enabled()) { | |
| struct device_node *msi_np = of_parse_phandle(pcie->np, "msi-parent", 0); | |
| if (msi_np == pcie->np) | |
| ret = brcm_pcie_enable_msi(pcie); | |
| of_node_put(msi_np); | |
| if (ret) { | |
| dev_err(pcie->dev, "probe of internal MSI failed"); | |
| goto fail; | |
| } | |
| } | |
| bridge->ops = pcie->cfg->soc_base == BCM7425 ? | |
| &brcm7425_pcie_ops : &brcm_pcie_ops; | |
| bridge->sysdata = pcie; | |
| platform_set_drvdata(pdev, pcie); | |
| ret = pci_host_probe(bridge); | |
| if (!ret && !brcm_pcie_link_up(pcie)) | |
| ret = -ENODEV; | |
| if (ret) { | |
| brcm_pcie_remove(pdev); | |
| return ret; | |
| } | |
| if (pcie->cfg->has_err_report) { | |
| spin_lock_init(&pcie->bridge_lock); | |
| brcm_register_die_notifiers(pcie); | |
| } | |
| return 0; | |
| fail: | |
| __brcm_pcie_remove(pcie); | |
| return ret; | |
| } | |
| MODULE_DEVICE_TABLE(of, brcm_pcie_match); | |
| static const struct dev_pm_ops brcm_pcie_pm_ops = { | |
| .suspend_noirq = brcm_pcie_suspend_noirq, | |
| .resume_noirq = brcm_pcie_resume_noirq, | |
| }; | |
| static struct platform_driver brcm_pcie_driver = { | |
| .probe = brcm_pcie_probe, | |
| .remove = brcm_pcie_remove, | |
| .driver = { | |
| .name = "brcm-pcie", | |
| .of_match_table = brcm_pcie_match, | |
| .pm = &brcm_pcie_pm_ops, | |
| }, | |
| }; | |
| module_platform_driver(brcm_pcie_driver); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DESCRIPTION("Broadcom STB PCIe RC driver"); | |
| MODULE_AUTHOR("Broadcom"); | |
| MODULE_SOFTDEP("pre: irq_bcm2712_mip"); |