| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Driver for the Aardvark PCIe controller, used on Marvell Armada | |
| * 3700. | |
| * | |
| * Copyright (C) 2016 Marvell | |
| * | |
| * Author: Hezi Shahmoon <hezi.shahmoon@marvell.com> | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/irqchip/irq-msi-lib.h> | |
| #include <linux/irqdomain.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/pci.h> | |
| #include <linux/pci-ecam.h> | |
| #include <linux/init.h> | |
| #include <linux/phy/phy.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/msi.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_pci.h> | |
| #include "pci-host-common.h" | |
| #include "../pci.h" | |
| #include "../pci-bridge-emul.h" | |
| /* PCIe core registers */ | |
| #define PCIE_CORE_DEV_ID_REG 0x0 | |
| #define PCIE_CORE_CMD_STATUS_REG 0x4 | |
| #define PCIE_CORE_DEV_REV_REG 0x8 | |
| #define PCIE_CORE_SSDEV_ID_REG 0x2c | |
| #define PCIE_CORE_PCIEXP_CAP 0xc0 | |
| #define PCIE_CORE_PCIERR_CAP 0x100 | |
| #define PCIE_CORE_ERR_CAPCTL_REG 0x118 | |
| #define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX BIT(5) | |
| #define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN BIT(6) | |
| #define PCIE_CORE_ERR_CAPCTL_ECRC_CHCK BIT(7) | |
| #define PCIE_CORE_ERR_CAPCTL_ECRC_CHCK_RCV BIT(8) | |
| /* PIO registers base address and register offsets */ | |
| #define PIO_BASE_ADDR 0x4000 | |
| #define PIO_CTRL (PIO_BASE_ADDR + 0x0) | |
| #define PIO_CTRL_TYPE_MASK GENMASK(3, 0) | |
| #define PIO_CTRL_ADDR_WIN_DISABLE BIT(24) | |
| #define PIO_STAT (PIO_BASE_ADDR + 0x4) | |
| #define PIO_COMPLETION_STATUS_SHIFT 7 | |
| #define PIO_COMPLETION_STATUS_MASK GENMASK(9, 7) | |
| #define PIO_COMPLETION_STATUS_OK 0 | |
| #define PIO_COMPLETION_STATUS_UR 1 | |
| #define PIO_COMPLETION_STATUS_RRS 2 | |
| #define PIO_COMPLETION_STATUS_CA 4 | |
| #define PIO_NON_POSTED_REQ BIT(10) | |
| #define PIO_ERR_STATUS BIT(11) | |
| #define PIO_ADDR_LS (PIO_BASE_ADDR + 0x8) | |
| #define PIO_ADDR_MS (PIO_BASE_ADDR + 0xc) | |
| #define PIO_WR_DATA (PIO_BASE_ADDR + 0x10) | |
| #define PIO_WR_DATA_STRB (PIO_BASE_ADDR + 0x14) | |
| #define PIO_RD_DATA (PIO_BASE_ADDR + 0x18) | |
| #define PIO_START (PIO_BASE_ADDR + 0x1c) | |
| #define PIO_ISR (PIO_BASE_ADDR + 0x20) | |
| #define PIO_ISRM (PIO_BASE_ADDR + 0x24) | |
| /* Aardvark Control registers */ | |
| #define CONTROL_BASE_ADDR 0x4800 | |
| #define PCIE_CORE_CTRL0_REG (CONTROL_BASE_ADDR + 0x0) | |
| #define PCIE_GEN_SEL_MSK 0x3 | |
| #define PCIE_GEN_SEL_SHIFT 0x0 | |
| #define SPEED_GEN_1 0 | |
| #define SPEED_GEN_2 1 | |
| #define SPEED_GEN_3 2 | |
| #define IS_RC_MSK 1 | |
| #define IS_RC_SHIFT 2 | |
| #define LANE_CNT_MSK 0x18 | |
| #define LANE_CNT_SHIFT 0x3 | |
| #define LANE_COUNT_1 (0 << LANE_CNT_SHIFT) | |
| #define LANE_COUNT_2 (1 << LANE_CNT_SHIFT) | |
| #define LANE_COUNT_4 (2 << LANE_CNT_SHIFT) | |
| #define LANE_COUNT_8 (3 << LANE_CNT_SHIFT) | |
| #define LINK_TRAINING_EN BIT(6) | |
| #define LEGACY_INTA BIT(28) | |
| #define LEGACY_INTB BIT(29) | |
| #define LEGACY_INTC BIT(30) | |
| #define LEGACY_INTD BIT(31) | |
| #define PCIE_CORE_CTRL1_REG (CONTROL_BASE_ADDR + 0x4) | |
| #define HOT_RESET_GEN BIT(0) | |
| #define PCIE_CORE_CTRL2_REG (CONTROL_BASE_ADDR + 0x8) | |
| #define PCIE_CORE_CTRL2_RESERVED 0x7 | |
| #define PCIE_CORE_CTRL2_TD_ENABLE BIT(4) | |
| #define PCIE_CORE_CTRL2_STRICT_ORDER_ENABLE BIT(5) | |
| #define PCIE_CORE_CTRL2_OB_WIN_ENABLE BIT(6) | |
| #define PCIE_CORE_CTRL2_MSI_ENABLE BIT(10) | |
| #define PCIE_CORE_REF_CLK_REG (CONTROL_BASE_ADDR + 0x14) | |
| #define PCIE_CORE_REF_CLK_TX_ENABLE BIT(1) | |
| #define PCIE_CORE_REF_CLK_RX_ENABLE BIT(2) | |
| #define PCIE_MSG_LOG_REG (CONTROL_BASE_ADDR + 0x30) | |
| #define PCIE_ISR0_REG (CONTROL_BASE_ADDR + 0x40) | |
| #define PCIE_MSG_PM_PME_MASK BIT(7) | |
| #define PCIE_ISR0_MASK_REG (CONTROL_BASE_ADDR + 0x44) | |
| #define PCIE_ISR0_MSI_INT_PENDING BIT(24) | |
| #define PCIE_ISR0_CORR_ERR BIT(11) | |
| #define PCIE_ISR0_NFAT_ERR BIT(12) | |
| #define PCIE_ISR0_FAT_ERR BIT(13) | |
| #define PCIE_ISR0_ERR_MASK GENMASK(13, 11) | |
| #define PCIE_ISR0_INTX_ASSERT(val) BIT(16 + (val)) | |
| #define PCIE_ISR0_INTX_DEASSERT(val) BIT(20 + (val)) | |
| #define PCIE_ISR0_ALL_MASK GENMASK(31, 0) | |
| #define PCIE_ISR1_REG (CONTROL_BASE_ADDR + 0x48) | |
| #define PCIE_ISR1_MASK_REG (CONTROL_BASE_ADDR + 0x4C) | |
| #define PCIE_ISR1_POWER_STATE_CHANGE BIT(4) | |
| #define PCIE_ISR1_FLUSH BIT(5) | |
| #define PCIE_ISR1_INTX_ASSERT(val) BIT(8 + (val)) | |
| #define PCIE_ISR1_ALL_MASK GENMASK(31, 0) | |
| #define PCIE_MSI_ADDR_LOW_REG (CONTROL_BASE_ADDR + 0x50) | |
| #define PCIE_MSI_ADDR_HIGH_REG (CONTROL_BASE_ADDR + 0x54) | |
| #define PCIE_MSI_STATUS_REG (CONTROL_BASE_ADDR + 0x58) | |
| #define PCIE_MSI_MASK_REG (CONTROL_BASE_ADDR + 0x5C) | |
| #define PCIE_MSI_ALL_MASK GENMASK(31, 0) | |
| #define PCIE_MSI_PAYLOAD_REG (CONTROL_BASE_ADDR + 0x9C) | |
| #define PCIE_MSI_DATA_MASK GENMASK(15, 0) | |
| /* PCIe window configuration */ | |
| #define OB_WIN_BASE_ADDR 0x4c00 | |
| #define OB_WIN_BLOCK_SIZE 0x20 | |
| #define OB_WIN_COUNT 8 | |
| #define OB_WIN_REG_ADDR(win, offset) (OB_WIN_BASE_ADDR + \ | |
| OB_WIN_BLOCK_SIZE * (win) + \ | |
| (offset)) | |
| #define OB_WIN_MATCH_LS(win) OB_WIN_REG_ADDR(win, 0x00) | |
| #define OB_WIN_ENABLE BIT(0) | |
| #define OB_WIN_MATCH_MS(win) OB_WIN_REG_ADDR(win, 0x04) | |
| #define OB_WIN_REMAP_LS(win) OB_WIN_REG_ADDR(win, 0x08) | |
| #define OB_WIN_REMAP_MS(win) OB_WIN_REG_ADDR(win, 0x0c) | |
| #define OB_WIN_MASK_LS(win) OB_WIN_REG_ADDR(win, 0x10) | |
| #define OB_WIN_MASK_MS(win) OB_WIN_REG_ADDR(win, 0x14) | |
| #define OB_WIN_ACTIONS(win) OB_WIN_REG_ADDR(win, 0x18) | |
| #define OB_WIN_DEFAULT_ACTIONS (OB_WIN_ACTIONS(OB_WIN_COUNT-1) + 0x4) | |
| #define OB_WIN_FUNC_NUM_MASK GENMASK(31, 24) | |
| #define OB_WIN_FUNC_NUM_SHIFT 24 | |
| #define OB_WIN_FUNC_NUM_ENABLE BIT(23) | |
| #define OB_WIN_BUS_NUM_BITS_MASK GENMASK(22, 20) | |
| #define OB_WIN_BUS_NUM_BITS_SHIFT 20 | |
| #define OB_WIN_MSG_CODE_ENABLE BIT(22) | |
| #define OB_WIN_MSG_CODE_MASK GENMASK(21, 14) | |
| #define OB_WIN_MSG_CODE_SHIFT 14 | |
| #define OB_WIN_MSG_PAYLOAD_LEN BIT(12) | |
| #define OB_WIN_ATTR_ENABLE BIT(11) | |
| #define OB_WIN_ATTR_TC_MASK GENMASK(10, 8) | |
| #define OB_WIN_ATTR_TC_SHIFT 8 | |
| #define OB_WIN_ATTR_RELAXED BIT(7) | |
| #define OB_WIN_ATTR_NOSNOOP BIT(6) | |
| #define OB_WIN_ATTR_POISON BIT(5) | |
| #define OB_WIN_ATTR_IDO BIT(4) | |
| #define OB_WIN_TYPE_MASK GENMASK(3, 0) | |
| #define OB_WIN_TYPE_SHIFT 0 | |
| #define OB_WIN_TYPE_MEM 0x0 | |
| #define OB_WIN_TYPE_IO 0x4 | |
| #define OB_WIN_TYPE_CONFIG_TYPE0 0x8 | |
| #define OB_WIN_TYPE_CONFIG_TYPE1 0x9 | |
| #define OB_WIN_TYPE_MSG 0xc | |
| /* LMI registers base address and register offsets */ | |
| #define LMI_BASE_ADDR 0x6000 | |
| #define CFG_REG (LMI_BASE_ADDR + 0x0) | |
| #define LTSSM_SHIFT 24 | |
| #define LTSSM_MASK 0x3f | |
| #define RC_BAR_CONFIG 0x300 | |
| /* LTSSM values in CFG_REG */ | |
| enum { | |
| LTSSM_DETECT_QUIET = 0x0, | |
| LTSSM_DETECT_ACTIVE = 0x1, | |
| LTSSM_POLLING_ACTIVE = 0x2, | |
| LTSSM_POLLING_COMPLIANCE = 0x3, | |
| LTSSM_POLLING_CONFIGURATION = 0x4, | |
| LTSSM_CONFIG_LINKWIDTH_START = 0x5, | |
| LTSSM_CONFIG_LINKWIDTH_ACCEPT = 0x6, | |
| LTSSM_CONFIG_LANENUM_ACCEPT = 0x7, | |
| LTSSM_CONFIG_LANENUM_WAIT = 0x8, | |
| LTSSM_CONFIG_COMPLETE = 0x9, | |
| LTSSM_CONFIG_IDLE = 0xa, | |
| LTSSM_RECOVERY_RCVR_LOCK = 0xb, | |
| LTSSM_RECOVERY_SPEED = 0xc, | |
| LTSSM_RECOVERY_RCVR_CFG = 0xd, | |
| LTSSM_RECOVERY_IDLE = 0xe, | |
| LTSSM_L0 = 0x10, | |
| LTSSM_RX_L0S_ENTRY = 0x11, | |
| LTSSM_RX_L0S_IDLE = 0x12, | |
| LTSSM_RX_L0S_FTS = 0x13, | |
| LTSSM_TX_L0S_ENTRY = 0x14, | |
| LTSSM_TX_L0S_IDLE = 0x15, | |
| LTSSM_TX_L0S_FTS = 0x16, | |
| LTSSM_L1_ENTRY = 0x17, | |
| LTSSM_L1_IDLE = 0x18, | |
| LTSSM_L2_IDLE = 0x19, | |
| LTSSM_L2_TRANSMIT_WAKE = 0x1a, | |
| LTSSM_DISABLED = 0x20, | |
| LTSSM_LOOPBACK_ENTRY_MASTER = 0x21, | |
| LTSSM_LOOPBACK_ACTIVE_MASTER = 0x22, | |
| LTSSM_LOOPBACK_EXIT_MASTER = 0x23, | |
| LTSSM_LOOPBACK_ENTRY_SLAVE = 0x24, | |
| LTSSM_LOOPBACK_ACTIVE_SLAVE = 0x25, | |
| LTSSM_LOOPBACK_EXIT_SLAVE = 0x26, | |
| LTSSM_HOT_RESET = 0x27, | |
| LTSSM_RECOVERY_EQUALIZATION_PHASE0 = 0x28, | |
| LTSSM_RECOVERY_EQUALIZATION_PHASE1 = 0x29, | |
| LTSSM_RECOVERY_EQUALIZATION_PHASE2 = 0x2a, | |
| LTSSM_RECOVERY_EQUALIZATION_PHASE3 = 0x2b, | |
| }; | |
| #define VENDOR_ID_REG (LMI_BASE_ADDR + 0x44) | |
| /* PCIe core controller registers */ | |
| #define CTRL_CORE_BASE_ADDR 0x18000 | |
| #define CTRL_CONFIG_REG (CTRL_CORE_BASE_ADDR + 0x0) | |
| #define CTRL_MODE_SHIFT 0x0 | |
| #define CTRL_MODE_MASK 0x1 | |
| #define PCIE_CORE_MODE_DIRECT 0x0 | |
| #define PCIE_CORE_MODE_COMMAND 0x1 | |
| /* PCIe Central Interrupts Registers */ | |
| #define CENTRAL_INT_BASE_ADDR 0x1b000 | |
| #define HOST_CTRL_INT_STATUS_REG (CENTRAL_INT_BASE_ADDR + 0x0) | |
| #define HOST_CTRL_INT_MASK_REG (CENTRAL_INT_BASE_ADDR + 0x4) | |
| #define PCIE_IRQ_CMDQ_INT BIT(0) | |
| #define PCIE_IRQ_MSI_STATUS_INT BIT(1) | |
| #define PCIE_IRQ_CMD_SENT_DONE BIT(3) | |
| #define PCIE_IRQ_DMA_INT BIT(4) | |
| #define PCIE_IRQ_IB_DXFERDONE BIT(5) | |
| #define PCIE_IRQ_OB_DXFERDONE BIT(6) | |
| #define PCIE_IRQ_OB_RXFERDONE BIT(7) | |
| #define PCIE_IRQ_COMPQ_INT BIT(12) | |
| #define PCIE_IRQ_DIR_RD_DDR_DET BIT(13) | |
| #define PCIE_IRQ_DIR_WR_DDR_DET BIT(14) | |
| #define PCIE_IRQ_CORE_INT BIT(16) | |
| #define PCIE_IRQ_CORE_INT_PIO BIT(17) | |
| #define PCIE_IRQ_DPMU_INT BIT(18) | |
| #define PCIE_IRQ_PCIE_MIS_INT BIT(19) | |
| #define PCIE_IRQ_MSI_INT1_DET BIT(20) | |
| #define PCIE_IRQ_MSI_INT2_DET BIT(21) | |
| #define PCIE_IRQ_RC_DBELL_DET BIT(22) | |
| #define PCIE_IRQ_EP_STATUS BIT(23) | |
| #define PCIE_IRQ_ALL_MASK GENMASK(31, 0) | |
| #define PCIE_IRQ_ENABLE_INTS_MASK PCIE_IRQ_CORE_INT | |
| /* Transaction types */ | |
| #define PCIE_CONFIG_RD_TYPE0 0x8 | |
| #define PCIE_CONFIG_RD_TYPE1 0x9 | |
| #define PCIE_CONFIG_WR_TYPE0 0xa | |
| #define PCIE_CONFIG_WR_TYPE1 0xb | |
| #define PIO_RETRY_CNT 750000 /* 1.5 s */ | |
| #define PIO_RETRY_DELAY 2 /* 2 us*/ | |
| #define RETRAIN_WAIT_MAX_RETRIES 10 | |
| #define RETRAIN_WAIT_USLEEP_US 2000 | |
| #define MSI_IRQ_NUM 32 | |
| #define CFG_RD_RRS_VAL 0xffff0001 | |
| struct advk_pcie { | |
| struct platform_device *pdev; | |
| void __iomem *base; | |
| struct { | |
| phys_addr_t match; | |
| phys_addr_t remap; | |
| phys_addr_t mask; | |
| u32 actions; | |
| } wins[OB_WIN_COUNT]; | |
| u8 wins_count; | |
| struct irq_domain *rp_irq_domain; | |
| struct irq_domain *irq_domain; | |
| struct irq_chip irq_chip; | |
| raw_spinlock_t irq_lock; | |
| struct irq_domain *msi_inner_domain; | |
| raw_spinlock_t msi_irq_lock; | |
| DECLARE_BITMAP(msi_used, MSI_IRQ_NUM); | |
| struct mutex msi_used_lock; | |
| int link_gen; | |
| struct pci_bridge_emul bridge; | |
| struct gpio_desc *reset_gpio; | |
| struct phy *phy; | |
| }; | |
| static inline void advk_writel(struct advk_pcie *pcie, u32 val, u64 reg) | |
| { | |
| writel(val, pcie->base + reg); | |
| } | |
| static inline u32 advk_readl(struct advk_pcie *pcie, u64 reg) | |
| { | |
| return readl(pcie->base + reg); | |
| } | |
| static u8 advk_pcie_ltssm_state(struct advk_pcie *pcie) | |
| { | |
| u32 val; | |
| u8 ltssm_state; | |
| val = advk_readl(pcie, CFG_REG); | |
| ltssm_state = (val >> LTSSM_SHIFT) & LTSSM_MASK; | |
| return ltssm_state; | |
| } | |
| static inline bool advk_pcie_link_up(struct advk_pcie *pcie) | |
| { | |
| /* check if LTSSM is in normal operation - some L* state */ | |
| u8 ltssm_state = advk_pcie_ltssm_state(pcie); | |
| return ltssm_state >= LTSSM_L0 && ltssm_state < LTSSM_DISABLED; | |
| } | |
| static inline bool advk_pcie_link_active(struct advk_pcie *pcie) | |
| { | |
| /* | |
| * According to PCIe Base specification 3.0, Table 4-14: Link | |
| * Status Mapped to the LTSSM, and 4.2.6.3.6 Configuration.Idle | |
| * is Link Up mapped to LTSSM Configuration.Idle, Recovery, L0, | |
| * L0s, L1 and L2 states. And according to 3.2.1. Data Link | |
| * Control and Management State Machine Rules is DL Up status | |
| * reported in DL Active state. | |
| */ | |
| u8 ltssm_state = advk_pcie_ltssm_state(pcie); | |
| return ltssm_state >= LTSSM_CONFIG_IDLE && ltssm_state < LTSSM_DISABLED; | |
| } | |
| static inline bool advk_pcie_link_training(struct advk_pcie *pcie) | |
| { | |
| /* | |
| * According to PCIe Base specification 3.0, Table 4-14: Link | |
| * Status Mapped to the LTSSM is Link Training mapped to LTSSM | |
| * Configuration and Recovery states. | |
| */ | |
| u8 ltssm_state = advk_pcie_ltssm_state(pcie); | |
| return ((ltssm_state >= LTSSM_CONFIG_LINKWIDTH_START && | |
| ltssm_state < LTSSM_L0) || | |
| (ltssm_state >= LTSSM_RECOVERY_EQUALIZATION_PHASE0 && | |
| ltssm_state <= LTSSM_RECOVERY_EQUALIZATION_PHASE3)); | |
| } | |
| static int advk_pcie_wait_for_link(struct advk_pcie *pcie) | |
| { | |
| int retries; | |
| /* check if the link is up or not */ | |
| for (retries = 0; retries < PCIE_LINK_WAIT_MAX_RETRIES; retries++) { | |
| if (advk_pcie_link_up(pcie)) { | |
| pci_host_common_link_train_delay(pcie->link_gen); | |
| return 0; | |
| } | |
| msleep(PCIE_LINK_WAIT_SLEEP_MS); | |
| } | |
| return -ETIMEDOUT; | |
| } | |
| static void advk_pcie_wait_for_retrain(struct advk_pcie *pcie) | |
| { | |
| size_t retries; | |
| for (retries = 0; retries < RETRAIN_WAIT_MAX_RETRIES; ++retries) { | |
| if (advk_pcie_link_training(pcie)) | |
| break; | |
| udelay(RETRAIN_WAIT_USLEEP_US); | |
| } | |
| } | |
| static void advk_pcie_issue_perst(struct advk_pcie *pcie) | |
| { | |
| if (!pcie->reset_gpio) | |
| return; | |
| /* 10ms delay is needed for some cards */ | |
| dev_info(&pcie->pdev->dev, "issuing PERST via reset GPIO for 10ms\n"); | |
| gpiod_set_value_cansleep(pcie->reset_gpio, 1); | |
| usleep_range(10000, 11000); | |
| gpiod_set_value_cansleep(pcie->reset_gpio, 0); | |
| } | |
| static void advk_pcie_train_link(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| u32 reg; | |
| int ret; | |
| /* | |
| * Setup PCIe rev / gen compliance based on device tree property | |
| * 'max-link-speed' which also forces maximal link speed. | |
| */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG); | |
| reg &= ~PCIE_GEN_SEL_MSK; | |
| if (pcie->link_gen == 3) | |
| reg |= SPEED_GEN_3; | |
| else if (pcie->link_gen == 2) | |
| reg |= SPEED_GEN_2; | |
| else | |
| reg |= SPEED_GEN_1; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG); | |
| /* | |
| * Set maximal link speed value also into PCIe Link Control 2 register. | |
| * Armada 3700 Functional Specification says that default value is based | |
| * on SPEED_GEN but tests showed that default value is always 8.0 GT/s. | |
| */ | |
| reg = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL2); | |
| reg &= ~PCI_EXP_LNKCTL2_TLS; | |
| if (pcie->link_gen == 3) | |
| reg |= PCI_EXP_LNKCTL2_TLS_8_0GT; | |
| else if (pcie->link_gen == 2) | |
| reg |= PCI_EXP_LNKCTL2_TLS_5_0GT; | |
| else | |
| reg |= PCI_EXP_LNKCTL2_TLS_2_5GT; | |
| advk_writel(pcie, reg, PCIE_CORE_PCIEXP_CAP + PCI_EXP_LNKCTL2); | |
| /* Enable link training after selecting PCIe generation */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG); | |
| reg |= LINK_TRAINING_EN; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG); | |
| /* | |
| * Reset PCIe card via PERST# signal. Some cards are not detected | |
| * during link training when they are in some non-initial state. | |
| */ | |
| advk_pcie_issue_perst(pcie); | |
| /* | |
| * PERST# signal could have been asserted by pinctrl subsystem before | |
| * probe() callback has been called or issued explicitly by reset gpio | |
| * function advk_pcie_issue_perst(), making the endpoint going into | |
| * fundamental reset. As required by PCI Express spec (PCI Express | |
| * Base Specification, REV. 4.0 PCI Express, February 19 2014, 6.6.1 | |
| * Conventional Reset) a delay for at least 100ms after such a reset | |
| * before sending a Configuration Request to the device is needed. | |
| * So wait until PCIe link is up. Function advk_pcie_wait_for_link() | |
| * waits for link at least 900ms. | |
| */ | |
| ret = advk_pcie_wait_for_link(pcie); | |
| if (ret < 0) | |
| dev_err(dev, "link never came up\n"); | |
| else | |
| dev_info(dev, "link up\n"); | |
| } | |
| /* | |
| * Set PCIe address window register which could be used for memory | |
| * mapping. | |
| */ | |
| static void advk_pcie_set_ob_win(struct advk_pcie *pcie, u8 win_num, | |
| phys_addr_t match, phys_addr_t remap, | |
| phys_addr_t mask, u32 actions) | |
| { | |
| advk_writel(pcie, OB_WIN_ENABLE | | |
| lower_32_bits(match), OB_WIN_MATCH_LS(win_num)); | |
| advk_writel(pcie, upper_32_bits(match), OB_WIN_MATCH_MS(win_num)); | |
| advk_writel(pcie, lower_32_bits(remap), OB_WIN_REMAP_LS(win_num)); | |
| advk_writel(pcie, upper_32_bits(remap), OB_WIN_REMAP_MS(win_num)); | |
| advk_writel(pcie, lower_32_bits(mask), OB_WIN_MASK_LS(win_num)); | |
| advk_writel(pcie, upper_32_bits(mask), OB_WIN_MASK_MS(win_num)); | |
| advk_writel(pcie, actions, OB_WIN_ACTIONS(win_num)); | |
| } | |
| static void advk_pcie_disable_ob_win(struct advk_pcie *pcie, u8 win_num) | |
| { | |
| advk_writel(pcie, 0, OB_WIN_MATCH_LS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_MATCH_MS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_REMAP_LS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_REMAP_MS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_MASK_LS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_MASK_MS(win_num)); | |
| advk_writel(pcie, 0, OB_WIN_ACTIONS(win_num)); | |
| } | |
| static void advk_pcie_setup_hw(struct advk_pcie *pcie) | |
| { | |
| phys_addr_t msi_addr; | |
| u32 reg; | |
| int i; | |
| /* | |
| * Configure PCIe Reference clock. Direction is from the PCIe | |
| * controller to the endpoint card, so enable transmitting of | |
| * Reference clock differential signal off-chip and disable | |
| * receiving off-chip differential signal. | |
| */ | |
| reg = advk_readl(pcie, PCIE_CORE_REF_CLK_REG); | |
| reg |= PCIE_CORE_REF_CLK_TX_ENABLE; | |
| reg &= ~PCIE_CORE_REF_CLK_RX_ENABLE; | |
| advk_writel(pcie, reg, PCIE_CORE_REF_CLK_REG); | |
| /* Set to Direct mode */ | |
| reg = advk_readl(pcie, CTRL_CONFIG_REG); | |
| reg &= ~(CTRL_MODE_MASK << CTRL_MODE_SHIFT); | |
| reg |= ((PCIE_CORE_MODE_DIRECT & CTRL_MODE_MASK) << CTRL_MODE_SHIFT); | |
| advk_writel(pcie, reg, CTRL_CONFIG_REG); | |
| /* Set PCI global control register to RC mode */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG); | |
| reg |= (IS_RC_MSK << IS_RC_SHIFT); | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG); | |
| /* | |
| * Replace incorrect PCI vendor id value 0x1b4b by correct value 0x11ab. | |
| * VENDOR_ID_REG contains vendor id in low 16 bits and subsystem vendor | |
| * id in high 16 bits. Updating this register changes readback value of | |
| * read-only vendor id bits in PCIE_CORE_DEV_ID_REG register. Workaround | |
| * for erratum 4.1: "The value of device and vendor ID is incorrect". | |
| */ | |
| reg = (PCI_VENDOR_ID_MARVELL << 16) | PCI_VENDOR_ID_MARVELL; | |
| advk_writel(pcie, reg, VENDOR_ID_REG); | |
| /* | |
| * Change Class Code of PCI Bridge device to PCI Bridge (0x600400), | |
| * because the default value is Mass storage controller (0x010400). | |
| * | |
| * Note that this Aardvark PCI Bridge does not have compliant Type 1 | |
| * Configuration Space and it even cannot be accessed via Aardvark's | |
| * PCI config space access method. Something like config space is | |
| * available in internal Aardvark registers starting at offset 0x0 | |
| * and is reported as Type 0. In range 0x10 - 0x34 it has totally | |
| * different registers. | |
| * | |
| * Therefore driver uses emulation of PCI Bridge which emulates | |
| * access to configuration space via internal Aardvark registers or | |
| * emulated configuration buffer. | |
| */ | |
| reg = advk_readl(pcie, PCIE_CORE_DEV_REV_REG); | |
| reg &= ~0xffffff00; | |
| reg |= PCI_CLASS_BRIDGE_PCI_NORMAL << 8; | |
| advk_writel(pcie, reg, PCIE_CORE_DEV_REV_REG); | |
| /* Disable Root Bridge I/O space, memory space and bus mastering */ | |
| reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG); | |
| reg &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); | |
| advk_writel(pcie, reg, PCIE_CORE_CMD_STATUS_REG); | |
| /* Set Advanced Error Capabilities and Control PF0 register */ | |
| reg = PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX | | |
| PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN | | |
| PCIE_CORE_ERR_CAPCTL_ECRC_CHCK | | |
| PCIE_CORE_ERR_CAPCTL_ECRC_CHCK_RCV; | |
| advk_writel(pcie, reg, PCIE_CORE_ERR_CAPCTL_REG); | |
| /* Set PCIe Device Control register */ | |
| reg = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + PCI_EXP_DEVCTL); | |
| reg &= ~PCI_EXP_DEVCTL_RELAX_EN; | |
| reg &= ~PCI_EXP_DEVCTL_NOSNOOP_EN; | |
| reg &= ~PCI_EXP_DEVCTL_PAYLOAD; | |
| reg &= ~PCI_EXP_DEVCTL_READRQ; | |
| reg |= PCI_EXP_DEVCTL_PAYLOAD_512B; | |
| reg |= PCI_EXP_DEVCTL_READRQ_512B; | |
| advk_writel(pcie, reg, PCIE_CORE_PCIEXP_CAP + PCI_EXP_DEVCTL); | |
| /* Program PCIe Control 2 to disable strict ordering */ | |
| reg = PCIE_CORE_CTRL2_RESERVED | | |
| PCIE_CORE_CTRL2_TD_ENABLE; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG); | |
| /* Set lane X1 */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG); | |
| reg &= ~LANE_CNT_MSK; | |
| reg |= LANE_COUNT_1; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG); | |
| /* Set MSI address */ | |
| msi_addr = virt_to_phys(pcie); | |
| advk_writel(pcie, lower_32_bits(msi_addr), PCIE_MSI_ADDR_LOW_REG); | |
| advk_writel(pcie, upper_32_bits(msi_addr), PCIE_MSI_ADDR_HIGH_REG); | |
| /* Enable MSI */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL2_REG); | |
| reg |= PCIE_CORE_CTRL2_MSI_ENABLE; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG); | |
| /* Clear all interrupts */ | |
| advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_STATUS_REG); | |
| advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_REG); | |
| advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_REG); | |
| advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_STATUS_REG); | |
| /* Disable All ISR0/1 and MSI Sources */ | |
| advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_MASK_REG); | |
| advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_MASK_REG); | |
| advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_MASK_REG); | |
| /* Unmask summary MSI interrupt */ | |
| reg = advk_readl(pcie, PCIE_ISR0_MASK_REG); | |
| reg &= ~PCIE_ISR0_MSI_INT_PENDING; | |
| advk_writel(pcie, reg, PCIE_ISR0_MASK_REG); | |
| /* Unmask PME interrupt for processing of PME requester */ | |
| reg = advk_readl(pcie, PCIE_ISR0_MASK_REG); | |
| reg &= ~PCIE_MSG_PM_PME_MASK; | |
| advk_writel(pcie, reg, PCIE_ISR0_MASK_REG); | |
| /* Enable summary interrupt for GIC SPI source */ | |
| reg = PCIE_IRQ_ALL_MASK & (~PCIE_IRQ_ENABLE_INTS_MASK); | |
| advk_writel(pcie, reg, HOST_CTRL_INT_MASK_REG); | |
| /* | |
| * Enable AXI address window location generation: | |
| * When it is enabled, the default outbound window | |
| * configurations (Default User Field: 0xD0074CFC) | |
| * are used to transparent address translation for | |
| * the outbound transactions. Thus, PCIe address | |
| * windows are not required for transparent memory | |
| * access when default outbound window configuration | |
| * is set for memory access. | |
| */ | |
| reg = advk_readl(pcie, PCIE_CORE_CTRL2_REG); | |
| reg |= PCIE_CORE_CTRL2_OB_WIN_ENABLE; | |
| advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG); | |
| /* | |
| * Set memory access in Default User Field so it | |
| * is not required to configure PCIe address for | |
| * transparent memory access. | |
| */ | |
| advk_writel(pcie, OB_WIN_TYPE_MEM, OB_WIN_DEFAULT_ACTIONS); | |
| /* | |
| * Bypass the address window mapping for PIO: | |
| * Since PIO access already contains all required | |
| * info over AXI interface by PIO registers, the | |
| * address window is not required. | |
| */ | |
| reg = advk_readl(pcie, PIO_CTRL); | |
| reg |= PIO_CTRL_ADDR_WIN_DISABLE; | |
| advk_writel(pcie, reg, PIO_CTRL); | |
| /* | |
| * Configure PCIe address windows for non-memory or | |
| * non-transparent access as by default PCIe uses | |
| * transparent memory access. | |
| */ | |
| for (i = 0; i < pcie->wins_count; i++) | |
| advk_pcie_set_ob_win(pcie, i, | |
| pcie->wins[i].match, pcie->wins[i].remap, | |
| pcie->wins[i].mask, pcie->wins[i].actions); | |
| /* Disable remaining PCIe outbound windows */ | |
| for (i = pcie->wins_count; i < OB_WIN_COUNT; i++) | |
| advk_pcie_disable_ob_win(pcie, i); | |
| advk_pcie_train_link(pcie); | |
| } | |
| static int advk_pcie_check_pio_status(struct advk_pcie *pcie, bool allow_rrs, u32 *val) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| u32 reg; | |
| unsigned int status; | |
| char *strcomp_status, *str_posted; | |
| int ret; | |
| reg = advk_readl(pcie, PIO_STAT); | |
| status = (reg & PIO_COMPLETION_STATUS_MASK) >> | |
| PIO_COMPLETION_STATUS_SHIFT; | |
| /* | |
| * According to HW spec, the PIO status check sequence as below: | |
| * 1) even if COMPLETION_STATUS(bit9:7) indicates successful, | |
| * it still needs to check Error Status(bit11), only when this bit | |
| * indicates no error happen, the operation is successful. | |
| * 2) value Unsupported Request(1) of COMPLETION_STATUS(bit9:7) only | |
| * means a PIO write error, and for PIO read it is successful with | |
| * a read value of 0xFFFFFFFF. | |
| * 3) value Config Request Retry Status(RRS) of COMPLETION_STATUS(bit9:7) | |
| * only means a PIO write error, and for PIO read it is successful | |
| * with a read value of 0xFFFF0001. | |
| * 4) value Completer Abort (CA) of COMPLETION_STATUS(bit9:7) means | |
| * error for both PIO read and PIO write operation. | |
| * 5) other errors are indicated as 'unknown'. | |
| */ | |
| switch (status) { | |
| case PIO_COMPLETION_STATUS_OK: | |
| if (reg & PIO_ERR_STATUS) { | |
| strcomp_status = "COMP_ERR"; | |
| ret = -EFAULT; | |
| break; | |
| } | |
| /* Get the read result */ | |
| if (val) | |
| *val = advk_readl(pcie, PIO_RD_DATA); | |
| /* No error */ | |
| strcomp_status = NULL; | |
| ret = 0; | |
| break; | |
| case PIO_COMPLETION_STATUS_UR: | |
| strcomp_status = "UR"; | |
| ret = -EOPNOTSUPP; | |
| break; | |
| case PIO_COMPLETION_STATUS_RRS: | |
| if (allow_rrs && val) { | |
| /* PCIe r6.0, sec 2.3.2, says: | |
| * If Configuration RRS Software Visibility is enabled: | |
| * For a Configuration Read Request that includes both | |
| * bytes of the Vendor ID field of a device Function's | |
| * Configuration Space Header, the Root Complex must | |
| * complete the Request to the host by returning a | |
| * read-data value of 0001h for the Vendor ID field and | |
| * all '1's for any additional bytes included in the | |
| * request. | |
| * | |
| * So RRS in this case is not an error status. | |
| */ | |
| *val = CFG_RD_RRS_VAL; | |
| strcomp_status = NULL; | |
| ret = 0; | |
| break; | |
| } | |
| /* PCIe r6.0, sec 2.3.2, says: | |
| * If RRS Software Visibility is not enabled, the Root Complex | |
| * must re-issue the Configuration Request as a new Request. | |
| * If RRS Software Visibility is enabled: For a Configuration | |
| * Write Request or for any other Configuration Read Request, | |
| * the Root Complex must re-issue the Configuration Request as | |
| * a new Request. | |
| * A Root Complex implementation may choose to limit the number | |
| * of Configuration Request/RRS Completion Status loops before | |
| * determining that something is wrong with the target of the | |
| * Request and taking appropriate action, e.g., complete the | |
| * Request to the host as a failed transaction. | |
| * | |
| * So return -EAGAIN and caller (pci-aardvark.c driver) will | |
| * re-issue request again up to the PIO_RETRY_CNT retries. | |
| */ | |
| strcomp_status = "RRS"; | |
| ret = -EAGAIN; | |
| break; | |
| case PIO_COMPLETION_STATUS_CA: | |
| strcomp_status = "CA"; | |
| ret = -ECANCELED; | |
| break; | |
| default: | |
| strcomp_status = "Unknown"; | |
| ret = -EINVAL; | |
| break; | |
| } | |
| if (!strcomp_status) | |
| return ret; | |
| if (reg & PIO_NON_POSTED_REQ) | |
| str_posted = "Non-posted"; | |
| else | |
| str_posted = "Posted"; | |
| dev_dbg(dev, "%s PIO Response Status: %s, %#x @ %#x\n", | |
| str_posted, strcomp_status, reg, advk_readl(pcie, PIO_ADDR_LS)); | |
| return ret; | |
| } | |
| static int advk_pcie_wait_pio(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| int i; | |
| for (i = 1; i <= PIO_RETRY_CNT; i++) { | |
| u32 start, isr; | |
| start = advk_readl(pcie, PIO_START); | |
| isr = advk_readl(pcie, PIO_ISR); | |
| if (!start && isr) | |
| return i; | |
| udelay(PIO_RETRY_DELAY); | |
| } | |
| dev_err(dev, "PIO read/write transfer time out\n"); | |
| return -ETIMEDOUT; | |
| } | |
| static pci_bridge_emul_read_status_t | |
| advk_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge, | |
| int reg, u32 *value) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| case PCI_COMMAND: | |
| *value = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG); | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| case PCI_INTERRUPT_LINE: { | |
| /* | |
| * From the whole 32bit register we support reading from HW only | |
| * two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR. | |
| * Other bits are retrieved only from emulated config buffer. | |
| */ | |
| __le32 *cfgspace = (__le32 *)&bridge->conf; | |
| u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]); | |
| if (advk_readl(pcie, PCIE_ISR0_MASK_REG) & PCIE_ISR0_ERR_MASK) | |
| val &= ~(PCI_BRIDGE_CTL_SERR << 16); | |
| else | |
| val |= PCI_BRIDGE_CTL_SERR << 16; | |
| if (advk_readl(pcie, PCIE_CORE_CTRL1_REG) & HOT_RESET_GEN) | |
| val |= PCI_BRIDGE_CTL_BUS_RESET << 16; | |
| else | |
| val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16); | |
| *value = val; | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| } | |
| default: | |
| return PCI_BRIDGE_EMUL_NOT_HANDLED; | |
| } | |
| } | |
| static void | |
| advk_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge, | |
| int reg, u32 old, u32 new, u32 mask) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| case PCI_COMMAND: | |
| advk_writel(pcie, new, PCIE_CORE_CMD_STATUS_REG); | |
| break; | |
| case PCI_INTERRUPT_LINE: | |
| /* | |
| * According to Figure 6-3: Pseudo Logic Diagram for Error | |
| * Message Controls in PCIe base specification, SERR# Enable bit | |
| * in Bridge Control register enable receiving of ERR_* messages | |
| */ | |
| if (mask & (PCI_BRIDGE_CTL_SERR << 16)) { | |
| u32 val = advk_readl(pcie, PCIE_ISR0_MASK_REG); | |
| if (new & (PCI_BRIDGE_CTL_SERR << 16)) | |
| val &= ~PCIE_ISR0_ERR_MASK; | |
| else | |
| val |= PCIE_ISR0_ERR_MASK; | |
| advk_writel(pcie, val, PCIE_ISR0_MASK_REG); | |
| } | |
| if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) { | |
| u32 val = advk_readl(pcie, PCIE_CORE_CTRL1_REG); | |
| if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16)) | |
| val |= HOT_RESET_GEN; | |
| else | |
| val &= ~HOT_RESET_GEN; | |
| advk_writel(pcie, val, PCIE_CORE_CTRL1_REG); | |
| } | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static pci_bridge_emul_read_status_t | |
| advk_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge, | |
| int reg, u32 *value) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| /* | |
| * PCI_EXP_SLTCAP, PCI_EXP_SLTCTL, PCI_EXP_RTCTL and PCI_EXP_RTSTA are | |
| * also supported, but do not need to be handled here, because their | |
| * values are stored in emulated config space buffer, and we read them | |
| * from there when needed. | |
| */ | |
| case PCI_EXP_LNKCAP: { | |
| u32 val = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg); | |
| /* | |
| * PCI_EXP_LNKCAP_DLLLARC bit is hardwired in aardvark HW to 0. | |
| * But support for PCI_EXP_LNKSTA_DLLLA is emulated via ltssm | |
| * state so explicitly enable PCI_EXP_LNKCAP_DLLLARC flag. | |
| */ | |
| val |= PCI_EXP_LNKCAP_DLLLARC; | |
| *value = val; | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| } | |
| case PCI_EXP_LNKCTL: { | |
| /* u32 contains both PCI_EXP_LNKCTL and PCI_EXP_LNKSTA */ | |
| u32 val = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg) & | |
| ~(PCI_EXP_LNKSTA_LT << 16); | |
| if (advk_pcie_link_training(pcie)) | |
| val |= (PCI_EXP_LNKSTA_LT << 16); | |
| if (advk_pcie_link_active(pcie)) | |
| val |= (PCI_EXP_LNKSTA_DLLLA << 16); | |
| *value = val; | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| } | |
| case PCI_EXP_DEVCAP: | |
| case PCI_EXP_DEVCTL: | |
| case PCI_EXP_DEVCAP2: | |
| case PCI_EXP_DEVCTL2: | |
| case PCI_EXP_LNKCAP2: | |
| case PCI_EXP_LNKCTL2: | |
| *value = advk_readl(pcie, PCIE_CORE_PCIEXP_CAP + reg); | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| default: | |
| return PCI_BRIDGE_EMUL_NOT_HANDLED; | |
| } | |
| } | |
| static void | |
| advk_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge, | |
| int reg, u32 old, u32 new, u32 mask) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| case PCI_EXP_LNKCTL: | |
| advk_writel(pcie, new, PCIE_CORE_PCIEXP_CAP + reg); | |
| if (new & PCI_EXP_LNKCTL_RL) | |
| advk_pcie_wait_for_retrain(pcie); | |
| break; | |
| case PCI_EXP_RTCTL: { | |
| u16 rootctl = le16_to_cpu(bridge->pcie_conf.rootctl); | |
| /* Only emulation of PMEIE and RRS_SVE bits is provided */ | |
| rootctl &= PCI_EXP_RTCTL_PMEIE | PCI_EXP_RTCTL_RRS_SVE; | |
| bridge->pcie_conf.rootctl = cpu_to_le16(rootctl); | |
| break; | |
| } | |
| /* | |
| * PCI_EXP_RTSTA is also supported, but does not need to be handled | |
| * here, because its value is stored in emulated config space buffer, | |
| * and we write it there when needed. | |
| */ | |
| case PCI_EXP_DEVCTL: | |
| case PCI_EXP_DEVCTL2: | |
| case PCI_EXP_LNKCTL2: | |
| advk_writel(pcie, new, PCIE_CORE_PCIEXP_CAP + reg); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static pci_bridge_emul_read_status_t | |
| advk_pci_bridge_emul_ext_conf_read(struct pci_bridge_emul *bridge, | |
| int reg, u32 *value) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| case 0: | |
| *value = advk_readl(pcie, PCIE_CORE_PCIERR_CAP + reg); | |
| /* | |
| * PCI_EXT_CAP_NEXT bits are set to offset 0x150, but Armada | |
| * 3700 Functional Specification does not document registers | |
| * at those addresses. | |
| * | |
| * Thus we clear PCI_EXT_CAP_NEXT bits to make Advanced Error | |
| * Reporting Capability header the last Extended Capability. | |
| * If we obtain documentation for those registers in the | |
| * future, this can be changed. | |
| */ | |
| *value &= 0x000fffff; | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| case PCI_ERR_UNCOR_STATUS: | |
| case PCI_ERR_UNCOR_MASK: | |
| case PCI_ERR_UNCOR_SEVER: | |
| case PCI_ERR_COR_STATUS: | |
| case PCI_ERR_COR_MASK: | |
| case PCI_ERR_CAP: | |
| case PCI_ERR_HEADER_LOG + 0: | |
| case PCI_ERR_HEADER_LOG + 4: | |
| case PCI_ERR_HEADER_LOG + 8: | |
| case PCI_ERR_HEADER_LOG + 12: | |
| case PCI_ERR_ROOT_COMMAND: | |
| case PCI_ERR_ROOT_STATUS: | |
| case PCI_ERR_ROOT_ERR_SRC: | |
| *value = advk_readl(pcie, PCIE_CORE_PCIERR_CAP + reg); | |
| return PCI_BRIDGE_EMUL_HANDLED; | |
| default: | |
| return PCI_BRIDGE_EMUL_NOT_HANDLED; | |
| } | |
| } | |
| static void | |
| advk_pci_bridge_emul_ext_conf_write(struct pci_bridge_emul *bridge, | |
| int reg, u32 old, u32 new, u32 mask) | |
| { | |
| struct advk_pcie *pcie = bridge->data; | |
| switch (reg) { | |
| /* These are W1C registers, so clear other bits */ | |
| case PCI_ERR_UNCOR_STATUS: | |
| case PCI_ERR_COR_STATUS: | |
| case PCI_ERR_ROOT_STATUS: | |
| new &= mask; | |
| fallthrough; | |
| case PCI_ERR_UNCOR_MASK: | |
| case PCI_ERR_UNCOR_SEVER: | |
| case PCI_ERR_COR_MASK: | |
| case PCI_ERR_CAP: | |
| case PCI_ERR_HEADER_LOG + 0: | |
| case PCI_ERR_HEADER_LOG + 4: | |
| case PCI_ERR_HEADER_LOG + 8: | |
| case PCI_ERR_HEADER_LOG + 12: | |
| case PCI_ERR_ROOT_COMMAND: | |
| case PCI_ERR_ROOT_ERR_SRC: | |
| advk_writel(pcie, new, PCIE_CORE_PCIERR_CAP + reg); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static const struct pci_bridge_emul_ops advk_pci_bridge_emul_ops = { | |
| .read_base = advk_pci_bridge_emul_base_conf_read, | |
| .write_base = advk_pci_bridge_emul_base_conf_write, | |
| .read_pcie = advk_pci_bridge_emul_pcie_conf_read, | |
| .write_pcie = advk_pci_bridge_emul_pcie_conf_write, | |
| .read_ext = advk_pci_bridge_emul_ext_conf_read, | |
| .write_ext = advk_pci_bridge_emul_ext_conf_write, | |
| }; | |
| /* | |
| * Initialize the configuration space of the PCI-to-PCI bridge | |
| * associated with the given PCIe interface. | |
| */ | |
| static int advk_sw_pci_bridge_init(struct advk_pcie *pcie) | |
| { | |
| struct pci_bridge_emul *bridge = &pcie->bridge; | |
| bridge->conf.vendor = | |
| cpu_to_le16(advk_readl(pcie, PCIE_CORE_DEV_ID_REG) & 0xffff); | |
| bridge->conf.device = | |
| cpu_to_le16(advk_readl(pcie, PCIE_CORE_DEV_ID_REG) >> 16); | |
| bridge->conf.class_revision = | |
| cpu_to_le32(advk_readl(pcie, PCIE_CORE_DEV_REV_REG) & 0xff); | |
| /* Support 32 bits I/O addressing */ | |
| bridge->conf.iobase = PCI_IO_RANGE_TYPE_32; | |
| bridge->conf.iolimit = PCI_IO_RANGE_TYPE_32; | |
| /* Support 64 bits memory pref */ | |
| bridge->conf.pref_mem_base = cpu_to_le16(PCI_PREF_RANGE_TYPE_64); | |
| bridge->conf.pref_mem_limit = cpu_to_le16(PCI_PREF_RANGE_TYPE_64); | |
| /* Support interrupt A for MSI feature */ | |
| bridge->conf.intpin = PCI_INTERRUPT_INTA; | |
| /* | |
| * Aardvark HW provides PCIe Capability structure in version 2 and | |
| * indicate slot support, which is emulated. | |
| */ | |
| bridge->pcie_conf.cap = cpu_to_le16(2 | PCI_EXP_FLAGS_SLOT); | |
| /* | |
| * Set Presence Detect State bit permanently since there is no support | |
| * for unplugging the card nor detecting whether it is plugged. (If a | |
| * platform exists in the future that supports it, via a GPIO for | |
| * example, it should be implemented via this bit.) | |
| * | |
| * Set physical slot number to 1 since there is only one port and zero | |
| * value is reserved for ports within the same silicon as Root Port | |
| * which is not our case. | |
| */ | |
| bridge->pcie_conf.slotcap = cpu_to_le32(FIELD_PREP(PCI_EXP_SLTCAP_PSN, | |
| 1)); | |
| bridge->pcie_conf.slotsta = cpu_to_le16(PCI_EXP_SLTSTA_PDS); | |
| /* Indicates supports for Completion Retry Status */ | |
| bridge->pcie_conf.rootcap = cpu_to_le16(PCI_EXP_RTCAP_RRS_SV); | |
| bridge->subsystem_vendor_id = advk_readl(pcie, PCIE_CORE_SSDEV_ID_REG) & 0xffff; | |
| bridge->subsystem_id = advk_readl(pcie, PCIE_CORE_SSDEV_ID_REG) >> 16; | |
| bridge->has_pcie = true; | |
| bridge->pcie_start = PCIE_CORE_PCIEXP_CAP; | |
| bridge->data = pcie; | |
| bridge->ops = &advk_pci_bridge_emul_ops; | |
| return pci_bridge_emul_init(bridge, 0); | |
| } | |
| static bool advk_pcie_valid_device(struct advk_pcie *pcie, struct pci_bus *bus, | |
| int devfn) | |
| { | |
| if (pci_is_root_bus(bus) && PCI_SLOT(devfn) != 0) | |
| return false; | |
| /* | |
| * If the link goes down after we check for link-up, we have a problem: | |
| * if a PIO request is executed while link-down, the whole controller | |
| * gets stuck in a non-functional state, and even after link comes up | |
| * again, PIO requests won't work anymore, and a reset of the whole PCIe | |
| * controller is needed. Therefore we need to prevent sending PIO | |
| * requests while the link is down. | |
| */ | |
| if (!pci_is_root_bus(bus) && !advk_pcie_link_up(pcie)) | |
| return false; | |
| return true; | |
| } | |
| static bool advk_pcie_pio_is_running(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| /* | |
| * Trying to start a new PIO transfer when previous has not completed | |
| * cause External Abort on CPU which results in kernel panic: | |
| * | |
| * SError Interrupt on CPU0, code 0xbf000002 -- SError | |
| * Kernel panic - not syncing: Asynchronous SError Interrupt | |
| * | |
| * Functions advk_pcie_rd_conf() and advk_pcie_wr_conf() are protected | |
| * by raw_spin_lock_irqsave() at pci_lock_config() level to prevent | |
| * concurrent calls at the same time. But because PIO transfer may take | |
| * about 1.5s when link is down or card is disconnected, it means that | |
| * advk_pcie_wait_pio() does not always have to wait for completion. | |
| * | |
| * Some versions of ARM Trusted Firmware handles this External Abort at | |
| * EL3 level and mask it to prevent kernel panic. Relevant TF-A commit: | |
| * https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50 | |
| */ | |
| if (advk_readl(pcie, PIO_START)) { | |
| dev_err(dev, "Previous PIO read/write transfer is still running\n"); | |
| return true; | |
| } | |
| return false; | |
| } | |
| static int advk_pcie_rd_conf(struct pci_bus *bus, u32 devfn, | |
| int where, int size, u32 *val) | |
| { | |
| struct advk_pcie *pcie = bus->sysdata; | |
| int retry_count; | |
| bool allow_rrs; | |
| u32 reg; | |
| int ret; | |
| if (!advk_pcie_valid_device(pcie, bus, devfn)) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| if (pci_is_root_bus(bus)) | |
| return pci_bridge_emul_conf_read(&pcie->bridge, where, | |
| size, val); | |
| /* | |
| * Configuration Request Retry Status (RRS) is possible to return | |
| * only when reading both bytes from PCI_VENDOR_ID at once and | |
| * RRS_SVE flag on Root Port is enabled. | |
| */ | |
| allow_rrs = (where == PCI_VENDOR_ID) && (size >= 2) && | |
| (le16_to_cpu(pcie->bridge.pcie_conf.rootctl) & | |
| PCI_EXP_RTCTL_RRS_SVE); | |
| if (advk_pcie_pio_is_running(pcie)) | |
| goto try_rrs; | |
| /* Program the control register */ | |
| reg = advk_readl(pcie, PIO_CTRL); | |
| reg &= ~PIO_CTRL_TYPE_MASK; | |
| if (pci_is_root_bus(bus->parent)) | |
| reg |= PCIE_CONFIG_RD_TYPE0; | |
| else | |
| reg |= PCIE_CONFIG_RD_TYPE1; | |
| advk_writel(pcie, reg, PIO_CTRL); | |
| /* Program the address registers */ | |
| reg = ALIGN_DOWN(PCIE_ECAM_OFFSET(bus->number, devfn, where), 4); | |
| advk_writel(pcie, reg, PIO_ADDR_LS); | |
| advk_writel(pcie, 0, PIO_ADDR_MS); | |
| /* Program the data strobe */ | |
| advk_writel(pcie, 0xf, PIO_WR_DATA_STRB); | |
| retry_count = 0; | |
| do { | |
| /* Clear PIO DONE ISR and start the transfer */ | |
| advk_writel(pcie, 1, PIO_ISR); | |
| advk_writel(pcie, 1, PIO_START); | |
| ret = advk_pcie_wait_pio(pcie); | |
| if (ret < 0) | |
| goto try_rrs; | |
| retry_count += ret; | |
| /* Check PIO status and get the read result */ | |
| ret = advk_pcie_check_pio_status(pcie, allow_rrs, val); | |
| } while (ret == -EAGAIN && retry_count < PIO_RETRY_CNT); | |
| if (ret < 0) | |
| goto fail; | |
| if (size == 1) | |
| *val = (*val >> (8 * (where & 3))) & 0xff; | |
| else if (size == 2) | |
| *val = (*val >> (8 * (where & 3))) & 0xffff; | |
| return PCIBIOS_SUCCESSFUL; | |
| try_rrs: | |
| /* | |
| * If it is possible, return Configuration Request Retry Status so | |
| * that caller tries to issue the request again instead of failing. | |
| */ | |
| if (allow_rrs) { | |
| *val = CFG_RD_RRS_VAL; | |
| return PCIBIOS_SUCCESSFUL; | |
| } | |
| fail: | |
| *val = 0xffffffff; | |
| return PCIBIOS_SET_FAILED; | |
| } | |
| static int advk_pcie_wr_conf(struct pci_bus *bus, u32 devfn, | |
| int where, int size, u32 val) | |
| { | |
| struct advk_pcie *pcie = bus->sysdata; | |
| u32 reg; | |
| u32 data_strobe = 0x0; | |
| int retry_count; | |
| int offset; | |
| int ret; | |
| if (!advk_pcie_valid_device(pcie, bus, devfn)) | |
| return PCIBIOS_DEVICE_NOT_FOUND; | |
| if (pci_is_root_bus(bus)) | |
| return pci_bridge_emul_conf_write(&pcie->bridge, where, | |
| size, val); | |
| if (where % size) | |
| return PCIBIOS_SET_FAILED; | |
| if (advk_pcie_pio_is_running(pcie)) | |
| return PCIBIOS_SET_FAILED; | |
| /* Program the control register */ | |
| reg = advk_readl(pcie, PIO_CTRL); | |
| reg &= ~PIO_CTRL_TYPE_MASK; | |
| if (pci_is_root_bus(bus->parent)) | |
| reg |= PCIE_CONFIG_WR_TYPE0; | |
| else | |
| reg |= PCIE_CONFIG_WR_TYPE1; | |
| advk_writel(pcie, reg, PIO_CTRL); | |
| /* Program the address registers */ | |
| reg = ALIGN_DOWN(PCIE_ECAM_OFFSET(bus->number, devfn, where), 4); | |
| advk_writel(pcie, reg, PIO_ADDR_LS); | |
| advk_writel(pcie, 0, PIO_ADDR_MS); | |
| /* Calculate the write strobe */ | |
| offset = where & 0x3; | |
| reg = val << (8 * offset); | |
| data_strobe = GENMASK(size - 1, 0) << offset; | |
| /* Program the data register */ | |
| advk_writel(pcie, reg, PIO_WR_DATA); | |
| /* Program the data strobe */ | |
| advk_writel(pcie, data_strobe, PIO_WR_DATA_STRB); | |
| retry_count = 0; | |
| do { | |
| /* Clear PIO DONE ISR and start the transfer */ | |
| advk_writel(pcie, 1, PIO_ISR); | |
| advk_writel(pcie, 1, PIO_START); | |
| ret = advk_pcie_wait_pio(pcie); | |
| if (ret < 0) | |
| return PCIBIOS_SET_FAILED; | |
| retry_count += ret; | |
| ret = advk_pcie_check_pio_status(pcie, false, NULL); | |
| } while (ret == -EAGAIN && retry_count < PIO_RETRY_CNT); | |
| return ret < 0 ? PCIBIOS_SET_FAILED : PCIBIOS_SUCCESSFUL; | |
| } | |
| static struct pci_ops advk_pcie_ops = { | |
| .read = advk_pcie_rd_conf, | |
| .write = advk_pcie_wr_conf, | |
| }; | |
| static void advk_msi_irq_compose_msi_msg(struct irq_data *data, | |
| struct msi_msg *msg) | |
| { | |
| struct advk_pcie *pcie = irq_data_get_irq_chip_data(data); | |
| phys_addr_t msi_addr = virt_to_phys(pcie); | |
| msg->address_lo = lower_32_bits(msi_addr); | |
| msg->address_hi = upper_32_bits(msi_addr); | |
| msg->data = data->hwirq; | |
| } | |
| static void advk_msi_irq_mask(struct irq_data *d) | |
| { | |
| struct advk_pcie *pcie = d->domain->host_data; | |
| irq_hw_number_t hwirq = irqd_to_hwirq(d); | |
| unsigned long flags; | |
| u32 mask; | |
| raw_spin_lock_irqsave(&pcie->msi_irq_lock, flags); | |
| mask = advk_readl(pcie, PCIE_MSI_MASK_REG); | |
| mask |= BIT(hwirq); | |
| advk_writel(pcie, mask, PCIE_MSI_MASK_REG); | |
| raw_spin_unlock_irqrestore(&pcie->msi_irq_lock, flags); | |
| } | |
| static void advk_msi_irq_unmask(struct irq_data *d) | |
| { | |
| struct advk_pcie *pcie = d->domain->host_data; | |
| irq_hw_number_t hwirq = irqd_to_hwirq(d); | |
| unsigned long flags; | |
| u32 mask; | |
| raw_spin_lock_irqsave(&pcie->msi_irq_lock, flags); | |
| mask = advk_readl(pcie, PCIE_MSI_MASK_REG); | |
| mask &= ~BIT(hwirq); | |
| advk_writel(pcie, mask, PCIE_MSI_MASK_REG); | |
| raw_spin_unlock_irqrestore(&pcie->msi_irq_lock, flags); | |
| } | |
| static struct irq_chip advk_msi_bottom_irq_chip = { | |
| .name = "MSI", | |
| .irq_compose_msi_msg = advk_msi_irq_compose_msi_msg, | |
| .irq_mask = advk_msi_irq_mask, | |
| .irq_unmask = advk_msi_irq_unmask, | |
| }; | |
| static int advk_msi_irq_domain_alloc(struct irq_domain *domain, | |
| unsigned int virq, | |
| unsigned int nr_irqs, void *args) | |
| { | |
| struct advk_pcie *pcie = domain->host_data; | |
| int hwirq, i; | |
| mutex_lock(&pcie->msi_used_lock); | |
| hwirq = bitmap_find_free_region(pcie->msi_used, MSI_IRQ_NUM, | |
| order_base_2(nr_irqs)); | |
| mutex_unlock(&pcie->msi_used_lock); | |
| if (hwirq < 0) | |
| return -ENOSPC; | |
| for (i = 0; i < nr_irqs; i++) | |
| irq_domain_set_info(domain, virq + i, hwirq + i, | |
| &advk_msi_bottom_irq_chip, | |
| domain->host_data, handle_simple_irq, | |
| NULL, NULL); | |
| return 0; | |
| } | |
| static void advk_msi_irq_domain_free(struct irq_domain *domain, | |
| unsigned int virq, unsigned int nr_irqs) | |
| { | |
| struct irq_data *d = irq_domain_get_irq_data(domain, virq); | |
| struct advk_pcie *pcie = domain->host_data; | |
| mutex_lock(&pcie->msi_used_lock); | |
| bitmap_release_region(pcie->msi_used, d->hwirq, order_base_2(nr_irqs)); | |
| mutex_unlock(&pcie->msi_used_lock); | |
| } | |
| static const struct irq_domain_ops advk_msi_domain_ops = { | |
| .alloc = advk_msi_irq_domain_alloc, | |
| .free = advk_msi_irq_domain_free, | |
| }; | |
| static void advk_pcie_irq_mask(struct irq_data *d) | |
| { | |
| struct advk_pcie *pcie = d->domain->host_data; | |
| irq_hw_number_t hwirq = irqd_to_hwirq(d); | |
| unsigned long flags; | |
| u32 mask; | |
| raw_spin_lock_irqsave(&pcie->irq_lock, flags); | |
| mask = advk_readl(pcie, PCIE_ISR1_MASK_REG); | |
| mask |= PCIE_ISR1_INTX_ASSERT(hwirq); | |
| advk_writel(pcie, mask, PCIE_ISR1_MASK_REG); | |
| raw_spin_unlock_irqrestore(&pcie->irq_lock, flags); | |
| } | |
| static void advk_pcie_irq_unmask(struct irq_data *d) | |
| { | |
| struct advk_pcie *pcie = d->domain->host_data; | |
| irq_hw_number_t hwirq = irqd_to_hwirq(d); | |
| unsigned long flags; | |
| u32 mask; | |
| raw_spin_lock_irqsave(&pcie->irq_lock, flags); | |
| mask = advk_readl(pcie, PCIE_ISR1_MASK_REG); | |
| mask &= ~PCIE_ISR1_INTX_ASSERT(hwirq); | |
| advk_writel(pcie, mask, PCIE_ISR1_MASK_REG); | |
| raw_spin_unlock_irqrestore(&pcie->irq_lock, flags); | |
| } | |
| static int advk_pcie_irq_map(struct irq_domain *h, | |
| unsigned int virq, irq_hw_number_t hwirq) | |
| { | |
| struct advk_pcie *pcie = h->host_data; | |
| irq_set_status_flags(virq, IRQ_LEVEL); | |
| irq_set_chip_and_handler(virq, &pcie->irq_chip, | |
| handle_level_irq); | |
| irq_set_chip_data(virq, pcie); | |
| return 0; | |
| } | |
| static const struct irq_domain_ops advk_pcie_irq_domain_ops = { | |
| .map = advk_pcie_irq_map, | |
| .xlate = irq_domain_xlate_onecell, | |
| }; | |
| #define ADVK_MSI_FLAGS_REQUIRED (MSI_FLAG_USE_DEF_DOM_OPS | \ | |
| MSI_FLAG_USE_DEF_CHIP_OPS | \ | |
| MSI_FLAG_PCI_MSI_MASK_PARENT | \ | |
| MSI_FLAG_NO_AFFINITY) | |
| #define ADVK_MSI_FLAGS_SUPPORTED (MSI_GENERIC_FLAGS_MASK | \ | |
| MSI_FLAG_PCI_MSIX | \ | |
| MSI_FLAG_MULTI_PCI_MSI) | |
| static const struct msi_parent_ops advk_msi_parent_ops = { | |
| .required_flags = ADVK_MSI_FLAGS_REQUIRED, | |
| .supported_flags = ADVK_MSI_FLAGS_SUPPORTED, | |
| .bus_select_token = DOMAIN_BUS_PCI_MSI, | |
| .prefix = "advk-", | |
| .init_dev_msi_info = msi_lib_init_dev_msi_info, | |
| }; | |
| static int advk_pcie_init_msi_irq_domain(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| raw_spin_lock_init(&pcie->msi_irq_lock); | |
| mutex_init(&pcie->msi_used_lock); | |
| struct irq_domain_info info = { | |
| .fwnode = dev_fwnode(dev), | |
| .ops = &advk_msi_domain_ops, | |
| .host_data = pcie, | |
| .size = MSI_IRQ_NUM, | |
| }; | |
| pcie->msi_inner_domain = msi_create_parent_irq_domain(&info, &advk_msi_parent_ops); | |
| if (!pcie->msi_inner_domain) | |
| return -ENOMEM; | |
| return 0; | |
| } | |
| static void advk_pcie_remove_msi_irq_domain(struct advk_pcie *pcie) | |
| { | |
| irq_domain_remove(pcie->msi_inner_domain); | |
| } | |
| static int advk_pcie_init_irq_domain(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| struct device_node *node = dev->of_node; | |
| struct device_node *pcie_intc_node; | |
| struct irq_chip *irq_chip; | |
| int ret = 0; | |
| raw_spin_lock_init(&pcie->irq_lock); | |
| pcie_intc_node = of_get_next_child(node, NULL); | |
| if (!pcie_intc_node) { | |
| dev_err(dev, "No PCIe Intc node found\n"); | |
| return -ENODEV; | |
| } | |
| irq_chip = &pcie->irq_chip; | |
| irq_chip->name = devm_kasprintf(dev, GFP_KERNEL, "%s-irq", | |
| dev_name(dev)); | |
| if (!irq_chip->name) { | |
| ret = -ENOMEM; | |
| goto out_put_node; | |
| } | |
| irq_chip->irq_mask = advk_pcie_irq_mask; | |
| irq_chip->irq_unmask = advk_pcie_irq_unmask; | |
| pcie->irq_domain = irq_domain_create_linear(of_fwnode_handle(pcie_intc_node), PCI_NUM_INTX, | |
| &advk_pcie_irq_domain_ops, pcie); | |
| if (!pcie->irq_domain) { | |
| dev_err(dev, "Failed to get a INTx IRQ domain\n"); | |
| ret = -ENOMEM; | |
| goto out_put_node; | |
| } | |
| out_put_node: | |
| of_node_put(pcie_intc_node); | |
| return ret; | |
| } | |
| static void advk_pcie_remove_irq_domain(struct advk_pcie *pcie) | |
| { | |
| irq_domain_remove(pcie->irq_domain); | |
| } | |
| static struct irq_chip advk_rp_irq_chip = { | |
| .name = "advk-RP", | |
| }; | |
| static int advk_pcie_rp_irq_map(struct irq_domain *h, | |
| unsigned int virq, irq_hw_number_t hwirq) | |
| { | |
| struct advk_pcie *pcie = h->host_data; | |
| irq_set_chip_and_handler(virq, &advk_rp_irq_chip, handle_simple_irq); | |
| irq_set_chip_data(virq, pcie); | |
| return 0; | |
| } | |
| static const struct irq_domain_ops advk_pcie_rp_irq_domain_ops = { | |
| .map = advk_pcie_rp_irq_map, | |
| .xlate = irq_domain_xlate_onecell, | |
| }; | |
| static int advk_pcie_init_rp_irq_domain(struct advk_pcie *pcie) | |
| { | |
| pcie->rp_irq_domain = irq_domain_create_linear(NULL, 1, &advk_pcie_rp_irq_domain_ops, pcie); | |
| if (!pcie->rp_irq_domain) { | |
| dev_err(&pcie->pdev->dev, "Failed to add Root Port IRQ domain\n"); | |
| return -ENOMEM; | |
| } | |
| return 0; | |
| } | |
| static void advk_pcie_remove_rp_irq_domain(struct advk_pcie *pcie) | |
| { | |
| irq_domain_remove(pcie->rp_irq_domain); | |
| } | |
| static void advk_pcie_handle_pme(struct advk_pcie *pcie) | |
| { | |
| u32 requester = advk_readl(pcie, PCIE_MSG_LOG_REG) >> 16; | |
| advk_writel(pcie, PCIE_MSG_PM_PME_MASK, PCIE_ISR0_REG); | |
| /* | |
| * PCIE_MSG_LOG_REG contains the last inbound message, so store | |
| * the requester ID only when PME was not asserted yet. | |
| * Also do not trigger PME interrupt when PME is still asserted. | |
| */ | |
| if (!(le32_to_cpu(pcie->bridge.pcie_conf.rootsta) & PCI_EXP_RTSTA_PME)) { | |
| pcie->bridge.pcie_conf.rootsta = cpu_to_le32(requester | PCI_EXP_RTSTA_PME); | |
| /* | |
| * Trigger PME interrupt only if PMEIE bit in Root Control is set. | |
| * Aardvark HW returns zero for PCI_EXP_FLAGS_IRQ, so use PCIe interrupt 0. | |
| */ | |
| if (!(le16_to_cpu(pcie->bridge.pcie_conf.rootctl) & PCI_EXP_RTCTL_PMEIE)) | |
| return; | |
| if (generic_handle_domain_irq(pcie->rp_irq_domain, 0) == -EINVAL) | |
| dev_err_ratelimited(&pcie->pdev->dev, "unhandled PME IRQ\n"); | |
| } | |
| } | |
| static void advk_pcie_handle_msi(struct advk_pcie *pcie) | |
| { | |
| u32 msi_val, msi_mask, msi_status, msi_idx; | |
| msi_mask = advk_readl(pcie, PCIE_MSI_MASK_REG); | |
| msi_val = advk_readl(pcie, PCIE_MSI_STATUS_REG); | |
| msi_status = msi_val & ((~msi_mask) & PCIE_MSI_ALL_MASK); | |
| for (msi_idx = 0; msi_idx < MSI_IRQ_NUM; msi_idx++) { | |
| if (!(BIT(msi_idx) & msi_status)) | |
| continue; | |
| advk_writel(pcie, BIT(msi_idx), PCIE_MSI_STATUS_REG); | |
| if (generic_handle_domain_irq(pcie->msi_inner_domain, msi_idx) == -EINVAL) | |
| dev_err_ratelimited(&pcie->pdev->dev, "unexpected MSI 0x%02x\n", msi_idx); | |
| } | |
| advk_writel(pcie, PCIE_ISR0_MSI_INT_PENDING, | |
| PCIE_ISR0_REG); | |
| } | |
| static void advk_pcie_handle_int(struct advk_pcie *pcie) | |
| { | |
| u32 isr0_val, isr0_mask, isr0_status; | |
| u32 isr1_val, isr1_mask, isr1_status; | |
| int i; | |
| isr0_val = advk_readl(pcie, PCIE_ISR0_REG); | |
| isr0_mask = advk_readl(pcie, PCIE_ISR0_MASK_REG); | |
| isr0_status = isr0_val & ((~isr0_mask) & PCIE_ISR0_ALL_MASK); | |
| isr1_val = advk_readl(pcie, PCIE_ISR1_REG); | |
| isr1_mask = advk_readl(pcie, PCIE_ISR1_MASK_REG); | |
| isr1_status = isr1_val & ((~isr1_mask) & PCIE_ISR1_ALL_MASK); | |
| /* Process PME interrupt as the first one to do not miss PME requester id */ | |
| if (isr0_status & PCIE_MSG_PM_PME_MASK) | |
| advk_pcie_handle_pme(pcie); | |
| /* Process ERR interrupt */ | |
| if (isr0_status & PCIE_ISR0_ERR_MASK) { | |
| advk_writel(pcie, PCIE_ISR0_ERR_MASK, PCIE_ISR0_REG); | |
| /* | |
| * Aardvark HW returns zero for PCI_ERR_ROOT_AER_IRQ, so use | |
| * PCIe interrupt 0 | |
| */ | |
| if (generic_handle_domain_irq(pcie->rp_irq_domain, 0) == -EINVAL) | |
| dev_err_ratelimited(&pcie->pdev->dev, "unhandled ERR IRQ\n"); | |
| } | |
| /* Process MSI interrupts */ | |
| if (isr0_status & PCIE_ISR0_MSI_INT_PENDING) | |
| advk_pcie_handle_msi(pcie); | |
| /* Process legacy interrupts */ | |
| for (i = 0; i < PCI_NUM_INTX; i++) { | |
| if (!(isr1_status & PCIE_ISR1_INTX_ASSERT(i))) | |
| continue; | |
| advk_writel(pcie, PCIE_ISR1_INTX_ASSERT(i), | |
| PCIE_ISR1_REG); | |
| if (generic_handle_domain_irq(pcie->irq_domain, i) == -EINVAL) | |
| dev_err_ratelimited(&pcie->pdev->dev, "unexpected INT%c IRQ\n", | |
| (char)i + 'A'); | |
| } | |
| } | |
| static irqreturn_t advk_pcie_irq_handler(int irq, void *arg) | |
| { | |
| struct advk_pcie *pcie = arg; | |
| u32 status; | |
| status = advk_readl(pcie, HOST_CTRL_INT_STATUS_REG); | |
| if (!(status & PCIE_IRQ_CORE_INT)) | |
| return IRQ_NONE; | |
| advk_pcie_handle_int(pcie); | |
| /* Clear interrupt */ | |
| advk_writel(pcie, PCIE_IRQ_CORE_INT, HOST_CTRL_INT_STATUS_REG); | |
| return IRQ_HANDLED; | |
| } | |
| static int advk_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) | |
| { | |
| struct advk_pcie *pcie = dev->bus->sysdata; | |
| /* | |
| * Emulated root bridge has its own emulated irq chip and irq domain. | |
| * Argument pin is the INTx pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and | |
| * hwirq for irq_create_mapping() is indexed from zero. | |
| */ | |
| if (pci_is_root_bus(dev->bus)) | |
| return irq_create_mapping(pcie->rp_irq_domain, pin - 1); | |
| else | |
| return of_irq_parse_and_map_pci(dev, slot, pin); | |
| } | |
| static void advk_pcie_disable_phy(struct advk_pcie *pcie) | |
| { | |
| phy_power_off(pcie->phy); | |
| phy_exit(pcie->phy); | |
| } | |
| static int advk_pcie_enable_phy(struct advk_pcie *pcie) | |
| { | |
| int ret; | |
| if (!pcie->phy) | |
| return 0; | |
| ret = phy_init(pcie->phy); | |
| if (ret) | |
| return ret; | |
| ret = phy_set_mode(pcie->phy, PHY_MODE_PCIE); | |
| if (ret) { | |
| phy_exit(pcie->phy); | |
| return ret; | |
| } | |
| ret = phy_power_on(pcie->phy); | |
| if (ret) { | |
| phy_exit(pcie->phy); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int advk_pcie_setup_phy(struct advk_pcie *pcie) | |
| { | |
| struct device *dev = &pcie->pdev->dev; | |
| struct device_node *node = dev->of_node; | |
| int ret = 0; | |
| pcie->phy = devm_of_phy_get(dev, node, NULL); | |
| if (IS_ERR(pcie->phy) && (PTR_ERR(pcie->phy) == -EPROBE_DEFER)) | |
| return PTR_ERR(pcie->phy); | |
| /* Old bindings miss the PHY handle */ | |
| if (IS_ERR(pcie->phy)) { | |
| dev_warn(dev, "PHY unavailable (%pe)\n", pcie->phy); | |
| pcie->phy = NULL; | |
| return 0; | |
| } | |
| ret = advk_pcie_enable_phy(pcie); | |
| if (ret) | |
| dev_err(dev, "Failed to initialize PHY (%d)\n", ret); | |
| return ret; | |
| } | |
| static int advk_pcie_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| struct advk_pcie *pcie; | |
| struct pci_host_bridge *bridge; | |
| struct resource_entry *entry; | |
| int ret, irq; | |
| bridge = devm_pci_alloc_host_bridge(dev, sizeof(struct advk_pcie)); | |
| if (!bridge) | |
| return -ENOMEM; | |
| pcie = pci_host_bridge_priv(bridge); | |
| pcie->pdev = pdev; | |
| platform_set_drvdata(pdev, pcie); | |
| resource_list_for_each_entry(entry, &bridge->windows) { | |
| resource_size_t start = entry->res->start; | |
| resource_size_t size = resource_size(entry->res); | |
| unsigned long type = resource_type(entry->res); | |
| u64 win_size; | |
| /* | |
| * Aardvark hardware allows to configure also PCIe window | |
| * for config type 0 and type 1 mapping, but driver uses | |
| * only PIO for issuing configuration transfers which does | |
| * not use PCIe window configuration. | |
| */ | |
| if (type != IORESOURCE_MEM && type != IORESOURCE_IO) | |
| continue; | |
| /* | |
| * Skip transparent memory resources. Default outbound access | |
| * configuration is set to transparent memory access so it | |
| * does not need window configuration. | |
| */ | |
| if (type == IORESOURCE_MEM && entry->offset == 0) | |
| continue; | |
| /* | |
| * The n-th PCIe window is configured by tuple (match, remap, mask) | |
| * and an access to address A uses this window if A matches the | |
| * match with given mask. | |
| * So every PCIe window size must be a power of two and every start | |
| * address must be aligned to window size. Minimal size is 64 KiB | |
| * because lower 16 bits of mask must be zero. Remapped address | |
| * may have set only bits from the mask. | |
| */ | |
| while (pcie->wins_count < OB_WIN_COUNT && size > 0) { | |
| /* Calculate the largest aligned window size */ | |
| win_size = (1ULL << (fls64(size)-1)) | | |
| (start ? (1ULL << __ffs64(start)) : 0); | |
| win_size = 1ULL << __ffs64(win_size); | |
| if (win_size < 0x10000) | |
| break; | |
| dev_dbg(dev, | |
| "Configuring PCIe window %d: [0x%llx-0x%llx] as %lu\n", | |
| pcie->wins_count, (unsigned long long)start, | |
| (unsigned long long)start + win_size, type); | |
| if (type == IORESOURCE_IO) { | |
| pcie->wins[pcie->wins_count].actions = OB_WIN_TYPE_IO; | |
| pcie->wins[pcie->wins_count].match = pci_pio_to_address(start); | |
| } else { | |
| pcie->wins[pcie->wins_count].actions = OB_WIN_TYPE_MEM; | |
| pcie->wins[pcie->wins_count].match = start; | |
| } | |
| pcie->wins[pcie->wins_count].remap = start - entry->offset; | |
| pcie->wins[pcie->wins_count].mask = ~(win_size - 1); | |
| if (pcie->wins[pcie->wins_count].remap & (win_size - 1)) | |
| break; | |
| start += win_size; | |
| size -= win_size; | |
| pcie->wins_count++; | |
| } | |
| if (size > 0) { | |
| dev_err(&pcie->pdev->dev, | |
| "Invalid PCIe region [0x%llx-0x%llx]\n", | |
| (unsigned long long)entry->res->start, | |
| (unsigned long long)entry->res->end + 1); | |
| return -EINVAL; | |
| } | |
| } | |
| pcie->base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(pcie->base)) | |
| return PTR_ERR(pcie->base); | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq < 0) | |
| return irq; | |
| ret = devm_request_irq(dev, irq, advk_pcie_irq_handler, | |
| IRQF_SHARED | IRQF_NO_THREAD, "advk-pcie", | |
| pcie); | |
| if (ret) { | |
| dev_err(dev, "Failed to register interrupt\n"); | |
| return ret; | |
| } | |
| pcie->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); | |
| ret = PTR_ERR_OR_ZERO(pcie->reset_gpio); | |
| if (ret) { | |
| if (ret != -EPROBE_DEFER) | |
| dev_err(dev, "Failed to get reset-gpio: %i\n", ret); | |
| return ret; | |
| } | |
| ret = gpiod_set_consumer_name(pcie->reset_gpio, "pcie1-reset"); | |
| if (ret) { | |
| dev_err(dev, "Failed to set reset gpio name: %d\n", ret); | |
| return ret; | |
| } | |
| ret = of_pci_get_max_link_speed(dev->of_node); | |
| if (ret <= 0 || ret > 3) | |
| pcie->link_gen = 3; | |
| else | |
| pcie->link_gen = ret; | |
| ret = advk_pcie_setup_phy(pcie); | |
| if (ret) | |
| return ret; | |
| advk_pcie_setup_hw(pcie); | |
| ret = advk_sw_pci_bridge_init(pcie); | |
| if (ret) { | |
| dev_err(dev, "Failed to register emulated root PCI bridge\n"); | |
| return ret; | |
| } | |
| ret = advk_pcie_init_irq_domain(pcie); | |
| if (ret) { | |
| dev_err(dev, "Failed to initialize irq\n"); | |
| return ret; | |
| } | |
| ret = advk_pcie_init_msi_irq_domain(pcie); | |
| if (ret) { | |
| dev_err(dev, "Failed to initialize irq\n"); | |
| advk_pcie_remove_irq_domain(pcie); | |
| return ret; | |
| } | |
| ret = advk_pcie_init_rp_irq_domain(pcie); | |
| if (ret) { | |
| dev_err(dev, "Failed to initialize irq\n"); | |
| advk_pcie_remove_msi_irq_domain(pcie); | |
| advk_pcie_remove_irq_domain(pcie); | |
| return ret; | |
| } | |
| bridge->sysdata = pcie; | |
| bridge->ops = &advk_pcie_ops; | |
| bridge->map_irq = advk_pcie_map_irq; | |
| ret = pci_host_probe(bridge); | |
| if (ret < 0) { | |
| advk_pcie_remove_rp_irq_domain(pcie); | |
| advk_pcie_remove_msi_irq_domain(pcie); | |
| advk_pcie_remove_irq_domain(pcie); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static void advk_pcie_remove(struct platform_device *pdev) | |
| { | |
| struct advk_pcie *pcie = platform_get_drvdata(pdev); | |
| struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); | |
| u32 val; | |
| int i; | |
| /* Remove PCI bus with all devices */ | |
| pci_lock_rescan_remove(); | |
| pci_stop_root_bus(bridge->bus); | |
| pci_remove_root_bus(bridge->bus); | |
| pci_unlock_rescan_remove(); | |
| /* Disable Root Bridge I/O space, memory space and bus mastering */ | |
| val = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG); | |
| val &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); | |
| advk_writel(pcie, val, PCIE_CORE_CMD_STATUS_REG); | |
| /* Disable MSI */ | |
| val = advk_readl(pcie, PCIE_CORE_CTRL2_REG); | |
| val &= ~PCIE_CORE_CTRL2_MSI_ENABLE; | |
| advk_writel(pcie, val, PCIE_CORE_CTRL2_REG); | |
| /* Clear MSI address */ | |
| advk_writel(pcie, 0, PCIE_MSI_ADDR_LOW_REG); | |
| advk_writel(pcie, 0, PCIE_MSI_ADDR_HIGH_REG); | |
| /* Mask all interrupts */ | |
| advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_MASK_REG); | |
| advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_MASK_REG); | |
| advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_MASK_REG); | |
| advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_MASK_REG); | |
| /* Clear all interrupts */ | |
| advk_writel(pcie, PCIE_MSI_ALL_MASK, PCIE_MSI_STATUS_REG); | |
| advk_writel(pcie, PCIE_ISR0_ALL_MASK, PCIE_ISR0_REG); | |
| advk_writel(pcie, PCIE_ISR1_ALL_MASK, PCIE_ISR1_REG); | |
| advk_writel(pcie, PCIE_IRQ_ALL_MASK, HOST_CTRL_INT_STATUS_REG); | |
| /* Remove IRQ domains */ | |
| advk_pcie_remove_rp_irq_domain(pcie); | |
| advk_pcie_remove_msi_irq_domain(pcie); | |
| advk_pcie_remove_irq_domain(pcie); | |
| /* Free config space for emulated root bridge */ | |
| pci_bridge_emul_cleanup(&pcie->bridge); | |
| /* Assert PERST# signal which prepares PCIe card for power down */ | |
| if (pcie->reset_gpio) | |
| gpiod_set_value_cansleep(pcie->reset_gpio, 1); | |
| /* Disable link training */ | |
| val = advk_readl(pcie, PCIE_CORE_CTRL0_REG); | |
| val &= ~LINK_TRAINING_EN; | |
| advk_writel(pcie, val, PCIE_CORE_CTRL0_REG); | |
| /* Disable outbound address windows mapping */ | |
| for (i = 0; i < OB_WIN_COUNT; i++) | |
| advk_pcie_disable_ob_win(pcie, i); | |
| /* Disable phy */ | |
| advk_pcie_disable_phy(pcie); | |
| } | |
| static const struct of_device_id advk_pcie_of_match_table[] = { | |
| { .compatible = "marvell,armada-3700-pcie", }, | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(of, advk_pcie_of_match_table); | |
| static struct platform_driver advk_pcie_driver = { | |
| .driver = { | |
| .name = "advk-pcie", | |
| .of_match_table = advk_pcie_of_match_table, | |
| }, | |
| .probe = advk_pcie_probe, | |
| .remove = advk_pcie_remove, | |
| }; | |
| module_platform_driver(advk_pcie_driver); | |
| MODULE_DESCRIPTION("Aardvark PCIe controller"); | |
| MODULE_LICENSE("GPL v2"); |