| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * PCIe host controller driver for Texas Instruments Keystone SoCs | |
| * | |
| * Copyright (C) 2013-2014 Texas Instruments., Ltd. | |
| * https://www.ti.com | |
| * | |
| * Author: Murali Karicheri <m-karicheri2@ti.com> | |
| * Implementation based on pci-exynos.c and pcie-designware.c | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irqchip/chained_irq.h> | |
| #include <linux/irqdomain.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/module.h> | |
| #include <linux/msi.h> | |
| #include <linux/of.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_pci.h> | |
| #include <linux/phy/phy.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regmap.h> | |
| #include <linux/resource.h> | |
| #include <linux/signal.h> | |
| #include "../../pci.h" | |
| #include "pcie-designware.h" | |
| #define PCIE_VENDORID_MASK 0xffff | |
| #define PCIE_DEVICEID_SHIFT 16 | |
| /* Application registers */ | |
| #define PID 0x000 | |
| #define RTL GENMASK(15, 11) | |
| #define RTL_SHIFT 11 | |
| #define AM6_PCI_PG1_RTL_VER 0x15 | |
| #define CMD_STATUS 0x004 | |
| #define LTSSM_EN_VAL BIT(0) | |
| #define OB_XLAT_EN_VAL BIT(1) | |
| #define DBI_CS2 BIT(5) | |
| #define CFG_SETUP 0x008 | |
| #define CFG_BUS(x) (((x) & 0xff) << 16) | |
| #define CFG_DEVICE(x) (((x) & 0x1f) << 8) | |
| #define CFG_FUNC(x) ((x) & 0x7) | |
| #define CFG_TYPE1 BIT(24) | |
| #define OB_SIZE 0x030 | |
| #define OB_OFFSET_INDEX(n) (0x200 + (8 * (n))) | |
| #define OB_OFFSET_HI(n) (0x204 + (8 * (n))) | |
| #define OB_ENABLEN BIT(0) | |
| #define OB_WIN_SIZE 8 /* 8MB */ | |
| #define PCIE_LEGACY_IRQ_ENABLE_SET(n) (0x188 + (0x10 * ((n) - 1))) | |
| #define PCIE_LEGACY_IRQ_ENABLE_CLR(n) (0x18c + (0x10 * ((n) - 1))) | |
| #define PCIE_EP_IRQ_SET 0x64 | |
| #define PCIE_EP_IRQ_CLR 0x68 | |
| #define INT_ENABLE BIT(0) | |
| /* IRQ register defines */ | |
| #define IRQ_EOI 0x050 | |
| #define MSI_IRQ 0x054 | |
| #define MSI_IRQ_STATUS(n) (0x104 + ((n) << 4)) | |
| #define MSI_IRQ_ENABLE_SET(n) (0x108 + ((n) << 4)) | |
| #define MSI_IRQ_ENABLE_CLR(n) (0x10c + ((n) << 4)) | |
| #define MSI_IRQ_OFFSET 4 | |
| #define IRQ_STATUS(n) (0x184 + ((n) << 4)) | |
| #define IRQ_ENABLE_SET(n) (0x188 + ((n) << 4)) | |
| #define INTx_EN BIT(0) | |
| #define ERR_IRQ_STATUS 0x1c4 | |
| #define ERR_IRQ_ENABLE_SET 0x1c8 | |
| #define ERR_AER BIT(5) /* ECRC error */ | |
| #define AM6_ERR_AER BIT(4) /* AM6 ECRC error */ | |
| #define ERR_AXI BIT(4) /* AXI tag lookup fatal error */ | |
| #define ERR_CORR BIT(3) /* Correctable error */ | |
| #define ERR_NONFATAL BIT(2) /* Non-fatal error */ | |
| #define ERR_FATAL BIT(1) /* Fatal error */ | |
| #define ERR_SYS BIT(0) /* System error */ | |
| #define ERR_IRQ_ALL (ERR_AER | ERR_AXI | ERR_CORR | \ | |
| ERR_NONFATAL | ERR_FATAL | ERR_SYS) | |
| /* PCIE controller device IDs */ | |
| #define PCIE_RC_K2HK 0xb008 | |
| #define PCIE_RC_K2E 0xb009 | |
| #define PCIE_RC_K2L 0xb00a | |
| #define PCIE_RC_K2G 0xb00b | |
| #define KS_PCIE_DEV_TYPE_MASK (0x3 << 1) | |
| #define KS_PCIE_DEV_TYPE(mode) ((mode) << 1) | |
| #define EP 0x0 | |
| #define LEG_EP 0x1 | |
| #define RC 0x2 | |
| #define KS_PCIE_SYSCLOCKOUTEN BIT(0) | |
| #define AM654_PCIE_DEV_TYPE_MASK 0x3 | |
| #define AM654_WIN_SIZE SZ_64K | |
| #define APP_ADDR_SPACE_0 (16 * SZ_1K) | |
| #define to_keystone_pcie(x) dev_get_drvdata((x)->dev) | |
| #define PCI_DEVICE_ID_TI_AM654X 0xb00c | |
| struct ks_pcie_of_data { | |
| enum dw_pcie_device_mode mode; | |
| const struct dw_pcie_host_ops *host_ops; | |
| const struct dw_pcie_ep_ops *ep_ops; | |
| u32 version; | |
| }; | |
| struct keystone_pcie { | |
| struct dw_pcie *pci; | |
| /* PCI Device ID */ | |
| u32 device_id; | |
| int intx_host_irqs[PCI_NUM_INTX]; | |
| int msi_host_irq; | |
| int num_lanes; | |
| u32 num_viewport; | |
| struct phy **phy; | |
| struct device_link **link; | |
| struct device_node *msi_intc_np; | |
| struct irq_domain *intx_irq_domain; | |
| struct device_node *np; | |
| /* Application register space */ | |
| void __iomem *va_app_base; /* DT 1st resource */ | |
| struct resource app; | |
| bool is_am6; | |
| }; | |
| static u32 ks_pcie_app_readl(struct keystone_pcie *ks_pcie, u32 offset) | |
| { | |
| return readl(ks_pcie->va_app_base + offset); | |
| } | |
| static void ks_pcie_app_writel(struct keystone_pcie *ks_pcie, u32 offset, | |
| u32 val) | |
| { | |
| writel(val, ks_pcie->va_app_base + offset); | |
| } | |
| static void ks_pcie_msi_irq_ack(struct irq_data *data) | |
| { | |
| struct dw_pcie_rp *pp = irq_data_get_irq_chip_data(data); | |
| struct keystone_pcie *ks_pcie; | |
| u32 irq = data->hwirq; | |
| struct dw_pcie *pci; | |
| u32 reg_offset; | |
| u32 bit_pos; | |
| pci = to_dw_pcie_from_pp(pp); | |
| ks_pcie = to_keystone_pcie(pci); | |
| reg_offset = irq % 8; | |
| bit_pos = irq >> 3; | |
| ks_pcie_app_writel(ks_pcie, MSI_IRQ_STATUS(reg_offset), | |
| BIT(bit_pos)); | |
| ks_pcie_app_writel(ks_pcie, IRQ_EOI, reg_offset + MSI_IRQ_OFFSET); | |
| } | |
| static void ks_pcie_compose_msi_msg(struct irq_data *data, struct msi_msg *msg) | |
| { | |
| struct dw_pcie_rp *pp = irq_data_get_irq_chip_data(data); | |
| struct keystone_pcie *ks_pcie; | |
| struct dw_pcie *pci; | |
| u64 msi_target; | |
| pci = to_dw_pcie_from_pp(pp); | |
| ks_pcie = to_keystone_pcie(pci); | |
| msi_target = ks_pcie->app.start + MSI_IRQ; | |
| msg->address_lo = lower_32_bits(msi_target); | |
| msg->address_hi = upper_32_bits(msi_target); | |
| msg->data = data->hwirq; | |
| dev_dbg(pci->dev, "msi#%d address_hi %#x address_lo %#x\n", | |
| (int)data->hwirq, msg->address_hi, msg->address_lo); | |
| } | |
| static void ks_pcie_msi_mask(struct irq_data *data) | |
| { | |
| struct dw_pcie_rp *pp = irq_data_get_irq_chip_data(data); | |
| struct keystone_pcie *ks_pcie; | |
| u32 irq = data->hwirq; | |
| struct dw_pcie *pci; | |
| unsigned long flags; | |
| u32 reg_offset; | |
| u32 bit_pos; | |
| raw_spin_lock_irqsave(&pp->lock, flags); | |
| pci = to_dw_pcie_from_pp(pp); | |
| ks_pcie = to_keystone_pcie(pci); | |
| reg_offset = irq % 8; | |
| bit_pos = irq >> 3; | |
| ks_pcie_app_writel(ks_pcie, MSI_IRQ_ENABLE_CLR(reg_offset), | |
| BIT(bit_pos)); | |
| raw_spin_unlock_irqrestore(&pp->lock, flags); | |
| } | |
| static void ks_pcie_msi_unmask(struct irq_data *data) | |
| { | |
| struct dw_pcie_rp *pp = irq_data_get_irq_chip_data(data); | |
| struct keystone_pcie *ks_pcie; | |
| u32 irq = data->hwirq; | |
| struct dw_pcie *pci; | |
| unsigned long flags; | |
| u32 reg_offset; | |
| u32 bit_pos; | |
| raw_spin_lock_irqsave(&pp->lock, flags); | |
| pci = to_dw_pcie_from_pp(pp); | |
| ks_pcie = to_keystone_pcie(pci); | |
| reg_offset = irq % 8; | |
| bit_pos = irq >> 3; | |
| ks_pcie_app_writel(ks_pcie, MSI_IRQ_ENABLE_SET(reg_offset), | |
| BIT(bit_pos)); | |
| raw_spin_unlock_irqrestore(&pp->lock, flags); | |
| } | |
| static struct irq_chip ks_pcie_msi_irq_chip = { | |
| .name = "KEYSTONE-PCI-MSI", | |
| .irq_ack = ks_pcie_msi_irq_ack, | |
| .irq_compose_msi_msg = ks_pcie_compose_msi_msg, | |
| .irq_mask = ks_pcie_msi_mask, | |
| .irq_unmask = ks_pcie_msi_unmask, | |
| }; | |
| /** | |
| * ks_pcie_set_dbi_mode() - Set DBI mode to access overlaid BAR mask registers | |
| * @ks_pcie: A pointer to the keystone_pcie structure which holds the KeyStone | |
| * PCIe host controller driver information. | |
| * | |
| * Since modification of dbi_cs2 involves different clock domain, read the | |
| * status back to ensure the transition is complete. | |
| */ | |
| static void ks_pcie_set_dbi_mode(struct keystone_pcie *ks_pcie) | |
| { | |
| u32 val; | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| val |= DBI_CS2; | |
| ks_pcie_app_writel(ks_pcie, CMD_STATUS, val); | |
| do { | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| } while (!(val & DBI_CS2)); | |
| } | |
| /** | |
| * ks_pcie_clear_dbi_mode() - Disable DBI mode | |
| * @ks_pcie: A pointer to the keystone_pcie structure which holds the KeyStone | |
| * PCIe host controller driver information. | |
| * | |
| * Since modification of dbi_cs2 involves different clock domain, read the | |
| * status back to ensure the transition is complete. | |
| */ | |
| static void ks_pcie_clear_dbi_mode(struct keystone_pcie *ks_pcie) | |
| { | |
| u32 val; | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| val &= ~DBI_CS2; | |
| ks_pcie_app_writel(ks_pcie, CMD_STATUS, val); | |
| do { | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| } while (val & DBI_CS2); | |
| } | |
| static int ks_pcie_msi_host_init(struct dw_pcie_rp *pp) | |
| { | |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| /* Configure and set up BAR0 */ | |
| ks_pcie_set_dbi_mode(ks_pcie); | |
| /* Enable BAR0 */ | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, 1); | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, SZ_4K - 1); | |
| ks_pcie_clear_dbi_mode(ks_pcie); | |
| /* | |
| * For BAR0, just setting bus address for inbound writes (MSI) should | |
| * be sufficient. Use physical address to avoid any conflicts. | |
| */ | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, ks_pcie->app.start); | |
| pp->msi_irq_chip = &ks_pcie_msi_irq_chip; | |
| return dw_pcie_allocate_domains(pp); | |
| } | |
| static void ks_pcie_handle_intx_irq(struct keystone_pcie *ks_pcie, | |
| int offset) | |
| { | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| struct device *dev = pci->dev; | |
| u32 pending; | |
| pending = ks_pcie_app_readl(ks_pcie, IRQ_STATUS(offset)); | |
| if (BIT(0) & pending) { | |
| dev_dbg(dev, ": irq: irq_offset %d", offset); | |
| generic_handle_domain_irq(ks_pcie->intx_irq_domain, offset); | |
| } | |
| /* EOI the INTx interrupt */ | |
| ks_pcie_app_writel(ks_pcie, IRQ_EOI, offset); | |
| } | |
| static void ks_pcie_enable_error_irq(struct keystone_pcie *ks_pcie) | |
| { | |
| ks_pcie_app_writel(ks_pcie, ERR_IRQ_ENABLE_SET, ERR_IRQ_ALL); | |
| } | |
| static irqreturn_t ks_pcie_handle_error_irq(struct keystone_pcie *ks_pcie) | |
| { | |
| u32 reg; | |
| struct device *dev = ks_pcie->pci->dev; | |
| reg = ks_pcie_app_readl(ks_pcie, ERR_IRQ_STATUS); | |
| if (!reg) | |
| return IRQ_NONE; | |
| if (reg & ERR_SYS) | |
| dev_err(dev, "System Error\n"); | |
| if (reg & ERR_FATAL) | |
| dev_err(dev, "Fatal Error\n"); | |
| if (reg & ERR_NONFATAL) | |
| dev_dbg(dev, "Non Fatal Error\n"); | |
| if (reg & ERR_CORR) | |
| dev_dbg(dev, "Correctable Error\n"); | |
| if (!ks_pcie->is_am6 && (reg & ERR_AXI)) | |
| dev_err(dev, "AXI tag lookup fatal Error\n"); | |
| if (reg & ERR_AER || (ks_pcie->is_am6 && (reg & AM6_ERR_AER))) | |
| dev_err(dev, "ECRC Error\n"); | |
| ks_pcie_app_writel(ks_pcie, ERR_IRQ_STATUS, reg); | |
| return IRQ_HANDLED; | |
| } | |
| static void ks_pcie_ack_intx_irq(struct irq_data *d) | |
| { | |
| } | |
| static void ks_pcie_mask_intx_irq(struct irq_data *d) | |
| { | |
| } | |
| static void ks_pcie_unmask_intx_irq(struct irq_data *d) | |
| { | |
| } | |
| static struct irq_chip ks_pcie_intx_irq_chip = { | |
| .name = "Keystone-PCI-INTX-IRQ", | |
| .irq_ack = ks_pcie_ack_intx_irq, | |
| .irq_mask = ks_pcie_mask_intx_irq, | |
| .irq_unmask = ks_pcie_unmask_intx_irq, | |
| }; | |
| static int ks_pcie_init_intx_irq_map(struct irq_domain *d, | |
| unsigned int irq, irq_hw_number_t hw_irq) | |
| { | |
| irq_set_chip_and_handler(irq, &ks_pcie_intx_irq_chip, | |
| handle_level_irq); | |
| irq_set_chip_data(irq, d->host_data); | |
| return 0; | |
| } | |
| static const struct irq_domain_ops ks_pcie_intx_irq_domain_ops = { | |
| .map = ks_pcie_init_intx_irq_map, | |
| .xlate = irq_domain_xlate_onetwocell, | |
| }; | |
| static int ks_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie) | |
| { | |
| u32 val; | |
| u32 num_viewport = ks_pcie->num_viewport; | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| struct dw_pcie_rp *pp = &pci->pp; | |
| struct resource_entry *entry; | |
| struct resource *mem; | |
| u64 start, end; | |
| int i; | |
| entry = resource_list_first_type(&pp->bridge->windows, IORESOURCE_MEM); | |
| if (!entry) | |
| return -ENODEV; | |
| mem = entry->res; | |
| start = mem->start; | |
| end = mem->end; | |
| /* Disable BARs for inbound access */ | |
| ks_pcie_set_dbi_mode(ks_pcie); | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, 0); | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_1, 0); | |
| ks_pcie_clear_dbi_mode(ks_pcie); | |
| if (ks_pcie->is_am6) | |
| return 0; | |
| val = ilog2(OB_WIN_SIZE); | |
| ks_pcie_app_writel(ks_pcie, OB_SIZE, val); | |
| /* Using Direct 1:1 mapping of RC <-> PCI memory space */ | |
| for (i = 0; i < num_viewport && (start < end); i++) { | |
| ks_pcie_app_writel(ks_pcie, OB_OFFSET_INDEX(i), | |
| lower_32_bits(start) | OB_ENABLEN); | |
| ks_pcie_app_writel(ks_pcie, OB_OFFSET_HI(i), | |
| upper_32_bits(start)); | |
| start += OB_WIN_SIZE * SZ_1M; | |
| } | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| val |= OB_XLAT_EN_VAL; | |
| ks_pcie_app_writel(ks_pcie, CMD_STATUS, val); | |
| return 0; | |
| } | |
| static void __iomem *ks_pcie_other_map_bus(struct pci_bus *bus, | |
| unsigned int devfn, int where) | |
| { | |
| struct dw_pcie_rp *pp = bus->sysdata; | |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| u32 reg; | |
| /* | |
| * Checking whether the link is up here is a last line of defense | |
| * against platforms that forward errors on the system bus as | |
| * SError upon PCI configuration transactions issued when the link | |
| * is down. This check is racy by definition and does not stop | |
| * the system from triggering an SError if the link goes down | |
| * after this check is performed. | |
| */ | |
| if (!dw_pcie_link_up(pci)) | |
| return NULL; | |
| reg = CFG_BUS(bus->number) | CFG_DEVICE(PCI_SLOT(devfn)) | | |
| CFG_FUNC(PCI_FUNC(devfn)); | |
| if (!pci_is_root_bus(bus->parent)) | |
| reg |= CFG_TYPE1; | |
| ks_pcie_app_writel(ks_pcie, CFG_SETUP, reg); | |
| return pp->va_cfg0_base + where; | |
| } | |
| static struct pci_ops ks_child_pcie_ops = { | |
| .map_bus = ks_pcie_other_map_bus, | |
| .read = pci_generic_config_read, | |
| .write = pci_generic_config_write, | |
| }; | |
| static struct pci_ops ks_pcie_ops = { | |
| .map_bus = dw_pcie_own_conf_map_bus, | |
| .read = pci_generic_config_read, | |
| .write = pci_generic_config_write, | |
| }; | |
| /** | |
| * ks_pcie_link_up() - Check if link up | |
| * @pci: A pointer to the dw_pcie structure which holds the DesignWare PCIe host | |
| * controller driver information. | |
| */ | |
| static bool ks_pcie_link_up(struct dw_pcie *pci) | |
| { | |
| u32 val; | |
| val = dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG0); | |
| return (val & PORT_LOGIC_LTSSM_STATE_MASK) == PORT_LOGIC_LTSSM_STATE_L0; | |
| } | |
| static void ks_pcie_stop_link(struct dw_pcie *pci) | |
| { | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| u32 val; | |
| /* Disable Link training */ | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| val &= ~LTSSM_EN_VAL; | |
| ks_pcie_app_writel(ks_pcie, CMD_STATUS, val); | |
| } | |
| static int ks_pcie_start_link(struct dw_pcie *pci) | |
| { | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| u32 val; | |
| /* Initiate Link Training */ | |
| val = ks_pcie_app_readl(ks_pcie, CMD_STATUS); | |
| ks_pcie_app_writel(ks_pcie, CMD_STATUS, LTSSM_EN_VAL | val); | |
| return 0; | |
| } | |
| static void ks_pcie_quirk(struct pci_dev *dev) | |
| { | |
| struct pci_bus *bus = dev->bus; | |
| struct keystone_pcie *ks_pcie; | |
| struct device *bridge_dev; | |
| struct pci_dev *bridge; | |
| u32 val; | |
| static const struct pci_device_id rc_pci_devids[] = { | |
| { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2HK), | |
| .class = PCI_CLASS_BRIDGE_PCI_NORMAL, .class_mask = ~0, }, | |
| { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2E), | |
| .class = PCI_CLASS_BRIDGE_PCI_NORMAL, .class_mask = ~0, }, | |
| { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2L), | |
| .class = PCI_CLASS_BRIDGE_PCI_NORMAL, .class_mask = ~0, }, | |
| { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2G), | |
| .class = PCI_CLASS_BRIDGE_PCI_NORMAL, .class_mask = ~0, }, | |
| { 0, }, | |
| }; | |
| static const struct pci_device_id am6_pci_devids[] = { | |
| { PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_AM654X), | |
| .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, }, | |
| { 0, }, | |
| }; | |
| if (pci_is_root_bus(bus)) | |
| bridge = dev; | |
| /* look for the host bridge */ | |
| while (!pci_is_root_bus(bus)) { | |
| bridge = bus->self; | |
| bus = bus->parent; | |
| } | |
| if (!bridge) | |
| return; | |
| /* | |
| * Keystone PCI controller has a h/w limitation of | |
| * 256 bytes maximum read request size. It can't handle | |
| * anything higher than this. So force this limit on | |
| * all downstream devices. | |
| */ | |
| if (pci_match_id(rc_pci_devids, bridge)) { | |
| if (pcie_get_readrq(dev) > 256) { | |
| dev_info(&dev->dev, "limiting MRRS to 256 bytes\n"); | |
| pcie_set_readrq(dev, 256); | |
| } | |
| } | |
| /* | |
| * Memory transactions fail with PCI controller in AM654 PG1.0 | |
| * when MRRS is set to more than 128 bytes. Force the MRRS to | |
| * 128 bytes in all downstream devices. | |
| */ | |
| if (pci_match_id(am6_pci_devids, bridge)) { | |
| bridge_dev = pci_get_host_bridge_device(dev); | |
| if (!bridge_dev || !bridge_dev->parent) | |
| return; | |
| ks_pcie = dev_get_drvdata(bridge_dev->parent); | |
| if (!ks_pcie) | |
| return; | |
| val = ks_pcie_app_readl(ks_pcie, PID); | |
| val &= RTL; | |
| val >>= RTL_SHIFT; | |
| if (val != AM6_PCI_PG1_RTL_VER) | |
| return; | |
| if (pcie_get_readrq(dev) > 128) { | |
| dev_info(&dev->dev, "limiting MRRS to 128 bytes\n"); | |
| pcie_set_readrq(dev, 128); | |
| } | |
| } | |
| } | |
| DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, ks_pcie_quirk); | |
| static void ks_pcie_msi_irq_handler(struct irq_desc *desc) | |
| { | |
| unsigned int irq = desc->irq_data.hwirq; | |
| struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc); | |
| u32 offset = irq - ks_pcie->msi_host_irq; | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| struct dw_pcie_rp *pp = &pci->pp; | |
| struct device *dev = pci->dev; | |
| struct irq_chip *chip = irq_desc_get_chip(desc); | |
| u32 vector, reg, pos; | |
| dev_dbg(dev, "%s, irq %d\n", __func__, irq); | |
| /* | |
| * The chained irq handler installation would have replaced normal | |
| * interrupt driver handler so we need to take care of mask/unmask and | |
| * ack operation. | |
| */ | |
| chained_irq_enter(chip, desc); | |
| reg = ks_pcie_app_readl(ks_pcie, MSI_IRQ_STATUS(offset)); | |
| /* | |
| * MSI0 status bit 0-3 shows vectors 0, 8, 16, 24, MSI1 status bit | |
| * shows 1, 9, 17, 25 and so forth | |
| */ | |
| for (pos = 0; pos < 4; pos++) { | |
| if (!(reg & BIT(pos))) | |
| continue; | |
| vector = offset + (pos << 3); | |
| dev_dbg(dev, "irq: bit %d, vector %d\n", pos, vector); | |
| generic_handle_domain_irq(pp->irq_domain, vector); | |
| } | |
| chained_irq_exit(chip, desc); | |
| } | |
| /** | |
| * ks_pcie_intx_irq_handler() - Handle INTX interrupt | |
| * @desc: Pointer to irq descriptor | |
| * | |
| * Traverse through pending INTX interrupts and invoke handler for each. Also | |
| * takes care of interrupt controller level mask/ack operation. | |
| */ | |
| static void ks_pcie_intx_irq_handler(struct irq_desc *desc) | |
| { | |
| unsigned int irq = irq_desc_get_irq(desc); | |
| struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc); | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| struct device *dev = pci->dev; | |
| u32 irq_offset = irq - ks_pcie->intx_host_irqs[0]; | |
| struct irq_chip *chip = irq_desc_get_chip(desc); | |
| dev_dbg(dev, ": Handling INTX irq %d\n", irq); | |
| /* | |
| * The chained irq handler installation would have replaced normal | |
| * interrupt driver handler so we need to take care of mask/unmask and | |
| * ack operation. | |
| */ | |
| chained_irq_enter(chip, desc); | |
| ks_pcie_handle_intx_irq(ks_pcie, irq_offset); | |
| chained_irq_exit(chip, desc); | |
| } | |
| static int ks_pcie_config_msi_irq(struct keystone_pcie *ks_pcie) | |
| { | |
| struct device *dev = ks_pcie->pci->dev; | |
| struct device_node *np = ks_pcie->np; | |
| struct device_node *intc_np; | |
| struct irq_data *irq_data; | |
| int irq_count, irq, ret, i; | |
| if (!IS_ENABLED(CONFIG_PCI_MSI)) | |
| return 0; | |
| intc_np = of_get_child_by_name(np, "msi-interrupt-controller"); | |
| if (!intc_np) { | |
| if (ks_pcie->is_am6) | |
| return 0; | |
| dev_warn(dev, "msi-interrupt-controller node is absent\n"); | |
| return -EINVAL; | |
| } | |
| irq_count = of_irq_count(intc_np); | |
| if (!irq_count) { | |
| dev_err(dev, "No IRQ entries in msi-interrupt-controller\n"); | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| for (i = 0; i < irq_count; i++) { | |
| irq = irq_of_parse_and_map(intc_np, i); | |
| if (!irq) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| if (!ks_pcie->msi_host_irq) { | |
| irq_data = irq_get_irq_data(irq); | |
| if (!irq_data) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| ks_pcie->msi_host_irq = irq_data->hwirq; | |
| } | |
| irq_set_chained_handler_and_data(irq, ks_pcie_msi_irq_handler, | |
| ks_pcie); | |
| } | |
| of_node_put(intc_np); | |
| return 0; | |
| err: | |
| of_node_put(intc_np); | |
| return ret; | |
| } | |
| static int ks_pcie_config_intx_irq(struct keystone_pcie *ks_pcie) | |
| { | |
| struct device *dev = ks_pcie->pci->dev; | |
| struct irq_domain *intx_irq_domain; | |
| struct device_node *np = ks_pcie->np; | |
| struct device_node *intc_np; | |
| int irq_count, irq, ret = 0, i; | |
| intc_np = of_get_child_by_name(np, "legacy-interrupt-controller"); | |
| if (!intc_np) { | |
| /* | |
| * Since INTX interrupts are modeled as edge-interrupts in | |
| * AM6, keep it disabled for now. | |
| */ | |
| if (ks_pcie->is_am6) | |
| return 0; | |
| dev_warn(dev, "legacy-interrupt-controller node is absent\n"); | |
| return -EINVAL; | |
| } | |
| irq_count = of_irq_count(intc_np); | |
| if (!irq_count) { | |
| dev_err(dev, "No IRQ entries in legacy-interrupt-controller\n"); | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| for (i = 0; i < irq_count; i++) { | |
| irq = irq_of_parse_and_map(intc_np, i); | |
| if (!irq) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| ks_pcie->intx_host_irqs[i] = irq; | |
| irq_set_chained_handler_and_data(irq, | |
| ks_pcie_intx_irq_handler, | |
| ks_pcie); | |
| } | |
| intx_irq_domain = irq_domain_create_linear(of_fwnode_handle(intc_np), PCI_NUM_INTX, | |
| &ks_pcie_intx_irq_domain_ops, NULL); | |
| if (!intx_irq_domain) { | |
| dev_err(dev, "Failed to add irq domain for INTX irqs\n"); | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| ks_pcie->intx_irq_domain = intx_irq_domain; | |
| for (i = 0; i < PCI_NUM_INTX; i++) | |
| ks_pcie_app_writel(ks_pcie, IRQ_ENABLE_SET(i), INTx_EN); | |
| err: | |
| of_node_put(intc_np); | |
| return ret; | |
| } | |
| static int ks_pcie_init_id(struct keystone_pcie *ks_pcie) | |
| { | |
| int ret; | |
| unsigned int id; | |
| struct regmap *devctrl_regs; | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| struct device *dev = pci->dev; | |
| struct device_node *np = dev->of_node; | |
| struct of_phandle_args args; | |
| unsigned int offset = 0; | |
| devctrl_regs = syscon_regmap_lookup_by_phandle(np, "ti,syscon-pcie-id"); | |
| if (IS_ERR(devctrl_regs)) | |
| return PTR_ERR(devctrl_regs); | |
| /* Do not error out to maintain old DT compatibility */ | |
| ret = of_parse_phandle_with_fixed_args(np, "ti,syscon-pcie-id", 1, 0, &args); | |
| if (!ret) | |
| offset = args.args[0]; | |
| ret = regmap_read(devctrl_regs, offset, &id); | |
| if (ret) | |
| return ret; | |
| dw_pcie_dbi_ro_wr_en(pci); | |
| dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, id & PCIE_VENDORID_MASK); | |
| dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, id >> PCIE_DEVICEID_SHIFT); | |
| dw_pcie_dbi_ro_wr_dis(pci); | |
| return 0; | |
| } | |
| static int ks_pcie_host_init(struct dw_pcie_rp *pp) | |
| { | |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| int ret; | |
| pp->bridge->ops = &ks_pcie_ops; | |
| if (!ks_pcie->is_am6) | |
| pp->bridge->child_ops = &ks_child_pcie_ops; | |
| ret = ks_pcie_config_intx_irq(ks_pcie); | |
| if (ret) | |
| return ret; | |
| ret = ks_pcie_config_msi_irq(ks_pcie); | |
| if (ret) | |
| return ret; | |
| ks_pcie_stop_link(pci); | |
| ret = ks_pcie_setup_rc_app_regs(ks_pcie); | |
| if (ret) | |
| return ret; | |
| writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8), | |
| pci->dbi_base + PCI_IO_BASE); | |
| ret = ks_pcie_init_id(ks_pcie); | |
| if (ret < 0) | |
| return ret; | |
| return 0; | |
| } | |
| static const struct dw_pcie_host_ops ks_pcie_host_ops = { | |
| .init = ks_pcie_host_init, | |
| .msi_init = ks_pcie_msi_host_init, | |
| }; | |
| static const struct dw_pcie_host_ops ks_pcie_am654_host_ops = { | |
| .init = ks_pcie_host_init, | |
| }; | |
| static irqreturn_t ks_pcie_err_irq_handler(int irq, void *priv) | |
| { | |
| struct keystone_pcie *ks_pcie = priv; | |
| return ks_pcie_handle_error_irq(ks_pcie); | |
| } | |
| static void ks_pcie_am654_write_dbi2(struct dw_pcie *pci, void __iomem *base, | |
| u32 reg, size_t size, u32 val) | |
| { | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| ks_pcie_set_dbi_mode(ks_pcie); | |
| dw_pcie_write(base + reg, size, val); | |
| ks_pcie_clear_dbi_mode(ks_pcie); | |
| } | |
| static const struct dw_pcie_ops ks_pcie_dw_pcie_ops = { | |
| .start_link = ks_pcie_start_link, | |
| .stop_link = ks_pcie_stop_link, | |
| .link_up = ks_pcie_link_up, | |
| .write_dbi2 = ks_pcie_am654_write_dbi2, | |
| }; | |
| static int ks_pcie_am654_ep_init(struct dw_pcie_ep *ep) | |
| { | |
| struct dw_pcie *pci = to_dw_pcie_from_ep(ep); | |
| int flags; | |
| ep->page_size = AM654_WIN_SIZE; | |
| flags = PCI_BASE_ADDRESS_SPACE_MEMORY | PCI_BASE_ADDRESS_MEM_TYPE_32; | |
| dw_pcie_writel_dbi2(pci, PCI_BASE_ADDRESS_0, APP_ADDR_SPACE_0 - 1); | |
| dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_0, flags); | |
| return 0; | |
| } | |
| static void ks_pcie_am654_raise_intx_irq(struct keystone_pcie *ks_pcie) | |
| { | |
| struct dw_pcie *pci = ks_pcie->pci; | |
| u8 int_pin; | |
| int_pin = dw_pcie_readb_dbi(pci, PCI_INTERRUPT_PIN); | |
| if (int_pin == 0 || int_pin > 4) | |
| return; | |
| ks_pcie_app_writel(ks_pcie, PCIE_LEGACY_IRQ_ENABLE_SET(int_pin), | |
| INT_ENABLE); | |
| ks_pcie_app_writel(ks_pcie, PCIE_EP_IRQ_SET, INT_ENABLE); | |
| mdelay(1); | |
| ks_pcie_app_writel(ks_pcie, PCIE_EP_IRQ_CLR, INT_ENABLE); | |
| ks_pcie_app_writel(ks_pcie, PCIE_LEGACY_IRQ_ENABLE_CLR(int_pin), | |
| INT_ENABLE); | |
| } | |
| static int ks_pcie_am654_raise_irq(struct dw_pcie_ep *ep, u8 func_no, | |
| unsigned int type, u16 interrupt_num) | |
| { | |
| struct dw_pcie *pci = to_dw_pcie_from_ep(ep); | |
| struct keystone_pcie *ks_pcie = to_keystone_pcie(pci); | |
| switch (type) { | |
| case PCI_IRQ_INTX: | |
| ks_pcie_am654_raise_intx_irq(ks_pcie); | |
| break; | |
| case PCI_IRQ_MSI: | |
| dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num); | |
| break; | |
| case PCI_IRQ_MSIX: | |
| dw_pcie_ep_raise_msix_irq(ep, func_no, interrupt_num); | |
| break; | |
| default: | |
| dev_err(pci->dev, "UNKNOWN IRQ type\n"); | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static const struct pci_epc_features ks_pcie_am654_epc_features = { | |
| DWC_EPC_COMMON_FEATURES, | |
| .msi_capable = true, | |
| .msix_capable = true, | |
| /* | |
| * TODO: This driver is the only DWC glue driver that had BAR_RESERVED | |
| * BARs, but did not call dw_pcie_ep_reset_bar() for the reserved BARs. | |
| * | |
| * To not change the existing behavior, these BARs were not migrated to | |
| * BAR_DISABLED. If this driver wants the BAR_RESERVED BARs to be | |
| * disabled, it should migrate them to BAR_DISABLED. | |
| * | |
| * If they actually should be enabled, then the driver must also define | |
| * what is behind these reserved BARs, see the definition of struct | |
| * pci_epc_bar_rsvd_region. | |
| */ | |
| .bar[BAR_0] = { .type = BAR_RESERVED, }, | |
| .bar[BAR_1] = { .type = BAR_RESERVED, }, | |
| .bar[BAR_2] = { .type = BAR_RESIZABLE, }, | |
| .bar[BAR_3] = { .type = BAR_FIXED, .fixed_size = SZ_64K, }, | |
| .bar[BAR_4] = { .type = BAR_FIXED, .fixed_size = 256, }, | |
| .bar[BAR_5] = { .type = BAR_RESIZABLE, }, | |
| .align = SZ_64K, | |
| }; | |
| static const struct pci_epc_features* | |
| ks_pcie_am654_get_features(struct dw_pcie_ep *ep) | |
| { | |
| return &ks_pcie_am654_epc_features; | |
| } | |
| static const struct dw_pcie_ep_ops ks_pcie_am654_ep_ops = { | |
| .init = ks_pcie_am654_ep_init, | |
| .raise_irq = ks_pcie_am654_raise_irq, | |
| .get_features = &ks_pcie_am654_get_features, | |
| }; | |
| static void ks_pcie_disable_phy(struct keystone_pcie *ks_pcie) | |
| { | |
| int num_lanes = ks_pcie->num_lanes; | |
| while (num_lanes--) { | |
| phy_power_off(ks_pcie->phy[num_lanes]); | |
| phy_exit(ks_pcie->phy[num_lanes]); | |
| } | |
| } | |
| static int ks_pcie_enable_phy(struct keystone_pcie *ks_pcie) | |
| { | |
| int i; | |
| int ret; | |
| int num_lanes = ks_pcie->num_lanes; | |
| for (i = 0; i < num_lanes; i++) { | |
| ret = phy_reset(ks_pcie->phy[i]); | |
| if (ret < 0) | |
| goto err_phy; | |
| ret = phy_init(ks_pcie->phy[i]); | |
| if (ret < 0) | |
| goto err_phy; | |
| ret = phy_power_on(ks_pcie->phy[i]); | |
| if (ret < 0) { | |
| phy_exit(ks_pcie->phy[i]); | |
| goto err_phy; | |
| } | |
| } | |
| return 0; | |
| err_phy: | |
| while (--i >= 0) { | |
| phy_power_off(ks_pcie->phy[i]); | |
| phy_exit(ks_pcie->phy[i]); | |
| } | |
| return ret; | |
| } | |
| static int ks_pcie_set_mode(struct device *dev) | |
| { | |
| struct device_node *np = dev->of_node; | |
| struct of_phandle_args args; | |
| unsigned int offset = 0; | |
| struct regmap *syscon; | |
| u32 val; | |
| u32 mask; | |
| int ret = 0; | |
| syscon = syscon_regmap_lookup_by_phandle(np, "ti,syscon-pcie-mode"); | |
| if (IS_ERR(syscon)) | |
| return 0; | |
| /* Do not error out to maintain old DT compatibility */ | |
| ret = of_parse_phandle_with_fixed_args(np, "ti,syscon-pcie-mode", 1, 0, &args); | |
| if (!ret) | |
| offset = args.args[0]; | |
| mask = KS_PCIE_DEV_TYPE_MASK | KS_PCIE_SYSCLOCKOUTEN; | |
| val = KS_PCIE_DEV_TYPE(RC) | KS_PCIE_SYSCLOCKOUTEN; | |
| ret = regmap_update_bits(syscon, offset, mask, val); | |
| if (ret) { | |
| dev_err(dev, "failed to set pcie mode\n"); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int ks_pcie_am654_set_mode(struct device *dev, | |
| enum dw_pcie_device_mode mode) | |
| { | |
| struct device_node *np = dev->of_node; | |
| struct of_phandle_args args; | |
| unsigned int offset = 0; | |
| struct regmap *syscon; | |
| u32 val; | |
| u32 mask; | |
| int ret = 0; | |
| syscon = syscon_regmap_lookup_by_phandle(np, "ti,syscon-pcie-mode"); | |
| if (IS_ERR(syscon)) | |
| return 0; | |
| /* Do not error out to maintain old DT compatibility */ | |
| ret = of_parse_phandle_with_fixed_args(np, "ti,syscon-pcie-mode", 1, 0, &args); | |
| if (!ret) | |
| offset = args.args[0]; | |
| mask = AM654_PCIE_DEV_TYPE_MASK; | |
| switch (mode) { | |
| case DW_PCIE_RC_TYPE: | |
| val = RC; | |
| break; | |
| case DW_PCIE_EP_TYPE: | |
| val = EP; | |
| break; | |
| default: | |
| dev_err(dev, "INVALID device type %d\n", mode); | |
| return -EINVAL; | |
| } | |
| ret = regmap_update_bits(syscon, offset, mask, val); | |
| if (ret) { | |
| dev_err(dev, "failed to set pcie mode\n"); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static const struct ks_pcie_of_data ks_pcie_rc_of_data = { | |
| .host_ops = &ks_pcie_host_ops, | |
| .mode = DW_PCIE_RC_TYPE, | |
| .version = DW_PCIE_VER_365A, | |
| }; | |
| static const struct ks_pcie_of_data ks_pcie_am654_rc_of_data = { | |
| .host_ops = &ks_pcie_am654_host_ops, | |
| .mode = DW_PCIE_RC_TYPE, | |
| .version = DW_PCIE_VER_490A, | |
| }; | |
| static const struct ks_pcie_of_data ks_pcie_am654_ep_of_data = { | |
| .ep_ops = &ks_pcie_am654_ep_ops, | |
| .mode = DW_PCIE_EP_TYPE, | |
| .version = DW_PCIE_VER_490A, | |
| }; | |
| static const struct of_device_id ks_pcie_of_match[] = { | |
| { | |
| .type = "pci", | |
| .data = &ks_pcie_rc_of_data, | |
| .compatible = "ti,keystone-pcie", | |
| }, | |
| { | |
| .data = &ks_pcie_am654_rc_of_data, | |
| .compatible = "ti,am654-pcie-rc", | |
| }, | |
| { | |
| .data = &ks_pcie_am654_ep_of_data, | |
| .compatible = "ti,am654-pcie-ep", | |
| }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, ks_pcie_of_match); | |
| static int ks_pcie_probe(struct platform_device *pdev) | |
| { | |
| const struct dw_pcie_host_ops *host_ops; | |
| const struct dw_pcie_ep_ops *ep_ops; | |
| struct device *dev = &pdev->dev; | |
| struct device_node *np = dev->of_node; | |
| const struct ks_pcie_of_data *data; | |
| enum dw_pcie_device_mode mode; | |
| struct dw_pcie *pci; | |
| struct keystone_pcie *ks_pcie; | |
| struct device_link **link; | |
| struct gpio_desc *gpiod; | |
| struct resource *res; | |
| void __iomem *base; | |
| u32 num_viewport; | |
| struct phy **phy; | |
| u32 num_lanes; | |
| char name[10]; | |
| u32 version; | |
| int ret; | |
| int irq; | |
| int i; | |
| data = of_device_get_match_data(dev); | |
| if (!data) | |
| return -EINVAL; | |
| version = data->version; | |
| host_ops = data->host_ops; | |
| ep_ops = data->ep_ops; | |
| mode = data->mode; | |
| ks_pcie = devm_kzalloc(dev, sizeof(*ks_pcie), GFP_KERNEL); | |
| if (!ks_pcie) | |
| return -ENOMEM; | |
| pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL); | |
| if (!pci) | |
| return -ENOMEM; | |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "app"); | |
| ks_pcie->va_app_base = devm_ioremap_resource(dev, res); | |
| if (IS_ERR(ks_pcie->va_app_base)) | |
| return PTR_ERR(ks_pcie->va_app_base); | |
| ks_pcie->app = *res; | |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbics"); | |
| base = devm_pci_remap_cfg_resource(dev, res); | |
| if (IS_ERR(base)) | |
| return PTR_ERR(base); | |
| if (of_device_is_compatible(np, "ti,am654-pcie-rc")) | |
| ks_pcie->is_am6 = true; | |
| pci->dbi_base = base; | |
| pci->dbi_base2 = base; | |
| pci->dev = dev; | |
| pci->ops = &ks_pcie_dw_pcie_ops; | |
| pci->version = version; | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq < 0) | |
| return irq; | |
| ret = devm_request_irq(dev, irq, ks_pcie_err_irq_handler, IRQF_SHARED, | |
| "ks-pcie-error-irq", ks_pcie); | |
| if (ret < 0) { | |
| dev_err(dev, "failed to request error IRQ %d\n", | |
| irq); | |
| return ret; | |
| } | |
| ret = of_property_read_u32(np, "num-lanes", &num_lanes); | |
| if (ret) | |
| num_lanes = 1; | |
| phy = devm_kcalloc(dev, num_lanes, sizeof(*phy), GFP_KERNEL); | |
| if (!phy) | |
| return -ENOMEM; | |
| link = devm_kcalloc(dev, num_lanes, sizeof(*link), GFP_KERNEL); | |
| if (!link) | |
| return -ENOMEM; | |
| for (i = 0; i < num_lanes; i++) { | |
| snprintf(name, sizeof(name), "pcie-phy%d", i); | |
| phy[i] = devm_phy_optional_get(dev, name); | |
| if (IS_ERR(phy[i])) { | |
| ret = PTR_ERR(phy[i]); | |
| goto err_link; | |
| } | |
| if (!phy[i]) | |
| continue; | |
| link[i] = device_link_add(dev, &phy[i]->dev, DL_FLAG_STATELESS); | |
| if (!link[i]) { | |
| ret = -EINVAL; | |
| goto err_link; | |
| } | |
| } | |
| ks_pcie->np = np; | |
| ks_pcie->pci = pci; | |
| ks_pcie->link = link; | |
| ks_pcie->num_lanes = num_lanes; | |
| ks_pcie->phy = phy; | |
| gpiod = devm_gpiod_get_optional(dev, "reset", | |
| GPIOD_OUT_LOW); | |
| if (IS_ERR(gpiod)) { | |
| ret = PTR_ERR(gpiod); | |
| if (ret != -EPROBE_DEFER) | |
| dev_err(dev, "Failed to get reset GPIO\n"); | |
| goto err_link; | |
| } | |
| /* Obtain references to the PHYs */ | |
| for (i = 0; i < num_lanes; i++) | |
| phy_pm_runtime_get_sync(ks_pcie->phy[i]); | |
| ret = ks_pcie_enable_phy(ks_pcie); | |
| /* Release references to the PHYs */ | |
| for (i = 0; i < num_lanes; i++) | |
| phy_pm_runtime_put_sync(ks_pcie->phy[i]); | |
| if (ret) { | |
| dev_err(dev, "failed to enable phy\n"); | |
| goto err_link; | |
| } | |
| platform_set_drvdata(pdev, ks_pcie); | |
| pm_runtime_enable(dev); | |
| ret = pm_runtime_get_sync(dev); | |
| if (ret < 0) { | |
| dev_err(dev, "pm_runtime_get_sync failed\n"); | |
| goto err_get_sync; | |
| } | |
| if (dw_pcie_ver_is_ge(pci, 480A)) | |
| ret = ks_pcie_am654_set_mode(dev, mode); | |
| else | |
| ret = ks_pcie_set_mode(dev); | |
| if (ret < 0) | |
| goto err_get_sync; | |
| switch (mode) { | |
| case DW_PCIE_RC_TYPE: | |
| if (!IS_ENABLED(CONFIG_PCI_KEYSTONE_HOST)) { | |
| ret = -ENODEV; | |
| goto err_get_sync; | |
| } | |
| ret = of_property_read_u32(np, "num-viewport", &num_viewport); | |
| if (ret < 0) { | |
| dev_err(dev, "unable to read *num-viewport* property\n"); | |
| goto err_get_sync; | |
| } | |
| /* | |
| * "Power Sequencing and Reset Signal Timings" table in | |
| * PCI EXPRESS CARD ELECTROMECHANICAL SPECIFICATION, REV. 2.0 | |
| * indicates PERST# should be deasserted after minimum of 100us | |
| * once REFCLK is stable. The REFCLK to the connector in RC | |
| * mode is selected while enabling the PHY. So deassert PERST# | |
| * after 100 us. | |
| */ | |
| if (gpiod) { | |
| usleep_range(100, 200); | |
| gpiod_set_value_cansleep(gpiod, 1); | |
| } | |
| ks_pcie->num_viewport = num_viewport; | |
| pci->pp.ops = host_ops; | |
| ret = dw_pcie_host_init(&pci->pp); | |
| if (ret < 0) | |
| goto err_get_sync; | |
| break; | |
| case DW_PCIE_EP_TYPE: | |
| if (!IS_ENABLED(CONFIG_PCI_KEYSTONE_EP)) { | |
| ret = -ENODEV; | |
| goto err_get_sync; | |
| } | |
| pci->ep.ops = ep_ops; | |
| ret = dw_pcie_ep_init(&pci->ep); | |
| if (ret < 0) | |
| goto err_get_sync; | |
| ret = dw_pcie_ep_init_registers(&pci->ep); | |
| if (ret) { | |
| dev_err(dev, "Failed to initialize DWC endpoint registers\n"); | |
| goto err_ep_init; | |
| } | |
| pci_epc_init_notify(pci->ep.epc); | |
| break; | |
| default: | |
| dev_err(dev, "INVALID device type %d\n", mode); | |
| ret = -EINVAL; | |
| goto err_get_sync; | |
| } | |
| ks_pcie_enable_error_irq(ks_pcie); | |
| return 0; | |
| err_ep_init: | |
| dw_pcie_ep_deinit(&pci->ep); | |
| err_get_sync: | |
| pm_runtime_put(dev); | |
| pm_runtime_disable(dev); | |
| ks_pcie_disable_phy(ks_pcie); | |
| err_link: | |
| while (--i >= 0 && link[i]) | |
| device_link_del(link[i]); | |
| return ret; | |
| } | |
| static void ks_pcie_remove(struct platform_device *pdev) | |
| { | |
| struct keystone_pcie *ks_pcie = platform_get_drvdata(pdev); | |
| struct device_link **link = ks_pcie->link; | |
| int num_lanes = ks_pcie->num_lanes; | |
| struct device *dev = &pdev->dev; | |
| pm_runtime_put(dev); | |
| pm_runtime_disable(dev); | |
| ks_pcie_disable_phy(ks_pcie); | |
| while (num_lanes--) | |
| device_link_del(link[num_lanes]); | |
| } | |
| static struct platform_driver ks_pcie_driver = { | |
| .probe = ks_pcie_probe, | |
| .remove = ks_pcie_remove, | |
| .driver = { | |
| .name = "keystone-pcie", | |
| .of_match_table = ks_pcie_of_match, | |
| }, | |
| }; | |
| #ifdef CONFIG_ARM | |
| /* | |
| * When a PCI device does not exist during config cycles, keystone host | |
| * gets a bus error instead of returning 0xffffffff (PCI_ERROR_RESPONSE). | |
| * This handler always returns 0 for this kind of fault. | |
| */ | |
| static int ks_pcie_fault(unsigned long addr, unsigned int fsr, | |
| struct pt_regs *regs) | |
| { | |
| unsigned long instr = *(unsigned long *)instruction_pointer(regs); | |
| if ((instr & 0x0e100090) == 0x00100090) { | |
| int reg = (instr >> 12) & 15; | |
| regs->uregs[reg] = -1; | |
| regs->ARM_pc += 4; | |
| } | |
| return 0; | |
| } | |
| static int __init ks_pcie_init(void) | |
| { | |
| struct device_node *np; | |
| /* | |
| * PCIe access errors that result into OCP errors are caught by ARM as | |
| * "External aborts" | |
| */ | |
| np = of_find_matching_node(NULL, ks_pcie_of_match); | |
| if (np) { | |
| of_node_put(np); | |
| hook_fault_code(17, ks_pcie_fault, SIGBUS, 0, | |
| "Asynchronous external abort"); | |
| } | |
| return platform_driver_register(&ks_pcie_driver); | |
| } | |
| device_initcall(ks_pcie_init); | |
| #else | |
| builtin_platform_driver(ks_pcie_driver); | |
| #endif | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DESCRIPTION("PCIe controller driver for Texas Instruments Keystone SoCs"); | |
| MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>"); |