| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright 2007-2008 Extreme Engineering Solutions, Inc. | |
| * | |
| * Author: Nate Case <ncase@xes-inc.com> | |
| * | |
| * LED driver for various PCA955x I2C LED drivers | |
| * | |
| * Supported devices: | |
| * | |
| * Device Description 7-bit slave address | |
| * ------ ----------- ------------------- | |
| * PCA9550 2-bit driver 0x60 .. 0x61 | |
| * PCA9551 8-bit driver 0x60 .. 0x67 | |
| * PCA9552 16-bit driver 0x60 .. 0x67 | |
| * PCA9553/01 4-bit driver 0x62 | |
| * PCA9553/02 4-bit driver 0x63 | |
| * | |
| * Philips PCA955x LED driver chips follow a register map as shown below: | |
| * | |
| * Control Register Description | |
| * ---------------- ----------- | |
| * 0x0 Input register 0 | |
| * .. | |
| * NUM_INPUT_REGS - 1 Last Input register X | |
| * | |
| * NUM_INPUT_REGS Frequency prescaler 0 | |
| * NUM_INPUT_REGS + 1 PWM register 0 | |
| * NUM_INPUT_REGS + 2 Frequency prescaler 1 | |
| * NUM_INPUT_REGS + 3 PWM register 1 | |
| * | |
| * NUM_INPUT_REGS + 4 LED selector 0 | |
| * NUM_INPUT_REGS + 4 | |
| * + NUM_LED_REGS - 1 Last LED selector | |
| * | |
| * where NUM_INPUT_REGS and NUM_LED_REGS vary depending on how many | |
| * bits the chip supports. | |
| */ | |
| #include <linux/bitops.h> | |
| #include <linux/ctype.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/gpio/driver.h> | |
| #include <linux/i2c.h> | |
| #include <linux/leds.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/property.h> | |
| #include <linux/slab.h> | |
| #include <linux/string.h> | |
| #include <dt-bindings/leds/leds-pca955x.h> | |
| /* LED select registers determine the source that drives LED outputs */ | |
| #define PCA955X_LS_LED_ON 0x0 /* Output LOW */ | |
| #define PCA955X_LS_LED_OFF 0x1 /* Output HI-Z */ | |
| #define PCA955X_LS_BLINK0 0x2 /* Blink at PWM0 rate */ | |
| #define PCA955X_LS_BLINK1 0x3 /* Blink at PWM1 rate */ | |
| #define PCA955X_GPIO_INPUT LED_OFF | |
| #define PCA955X_GPIO_HIGH LED_OFF | |
| #define PCA955X_GPIO_LOW LED_FULL | |
| #define PCA955X_BLINK_DEFAULT_MS 1000 | |
| enum pca955x_type { | |
| pca9550, | |
| pca9551, | |
| pca9552, | |
| ibm_pca9552, | |
| pca9553, | |
| }; | |
| struct pca955x_chipdef { | |
| u8 bits; | |
| u8 slv_addr; /* 7-bit slave address mask */ | |
| int slv_addr_shift; /* Number of bits to ignore */ | |
| int blink_div; /* PSC divider */ | |
| }; | |
| static const struct pca955x_chipdef pca955x_chipdefs[] = { | |
| [pca9550] = { | |
| .bits = 2, | |
| .slv_addr = /* 110000x */ 0x60, | |
| .slv_addr_shift = 1, | |
| .blink_div = 44, | |
| }, | |
| [pca9551] = { | |
| .bits = 8, | |
| .slv_addr = /* 1100xxx */ 0x60, | |
| .slv_addr_shift = 3, | |
| .blink_div = 38, | |
| }, | |
| [pca9552] = { | |
| .bits = 16, | |
| .slv_addr = /* 1100xxx */ 0x60, | |
| .slv_addr_shift = 3, | |
| .blink_div = 44, | |
| }, | |
| [ibm_pca9552] = { | |
| .bits = 16, | |
| .slv_addr = /* 0110xxx */ 0x30, | |
| .slv_addr_shift = 3, | |
| .blink_div = 44, | |
| }, | |
| [pca9553] = { | |
| .bits = 4, | |
| .slv_addr = /* 110001x */ 0x62, | |
| .slv_addr_shift = 1, | |
| .blink_div = 44, | |
| }, | |
| }; | |
| struct pca955x { | |
| struct mutex lock; | |
| struct pca955x_led *leds; | |
| const struct pca955x_chipdef *chipdef; | |
| struct i2c_client *client; | |
| unsigned long active_blink; | |
| unsigned long active_pins; | |
| unsigned long blink_period; | |
| #ifdef CONFIG_LEDS_PCA955X_GPIO | |
| struct gpio_chip gpio; | |
| #endif | |
| }; | |
| struct pca955x_led { | |
| struct pca955x *pca955x; | |
| struct led_classdev led_cdev; | |
| int led_num; /* 0 .. 15 potentially */ | |
| u32 type; | |
| enum led_default_state default_state; | |
| struct fwnode_handle *fwnode; | |
| }; | |
| #define led_to_pca955x(l) container_of(l, struct pca955x_led, led_cdev) | |
| struct pca955x_platform_data { | |
| struct pca955x_led *leds; | |
| int num_leds; | |
| }; | |
| /* 8 bits per input register */ | |
| static inline u8 pca955x_num_input_regs(u8 bits) | |
| { | |
| return (bits + 7) / 8; | |
| } | |
| /* 4 bits per LED selector register */ | |
| static inline u8 pca955x_num_led_regs(u8 bits) | |
| { | |
| return (bits + 3) / 4; | |
| } | |
| /* | |
| * Return an LED selector register value based on an existing one, with | |
| * the appropriate 2-bit state value set for the given LED number (0-3). | |
| */ | |
| static inline u8 pca955x_ledsel(u8 oldval, int led_num, int state) | |
| { | |
| return (oldval & (~(0x3 << (led_num << 1)))) | | |
| ((state & 0x3) << (led_num << 1)); | |
| } | |
| static inline int pca955x_ledstate(u8 ls, int led_num) | |
| { | |
| return (ls >> (led_num << 1)) & 0x3; | |
| } | |
| /* | |
| * Write to frequency prescaler register, used to program the | |
| * period of the PWM output. period = (PSCx + 1) / coeff | |
| * Where for pca9551 chips coeff = 38 and for all other chips coeff = 44 | |
| */ | |
| static int pca955x_write_psc(struct pca955x *pca955x, int n, u8 val) | |
| { | |
| u8 cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + (2 * n); | |
| int ret; | |
| ret = i2c_smbus_write_byte_data(pca955x->client, cmd, val); | |
| if (ret < 0) | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", __func__, n, | |
| val, ret); | |
| return ret; | |
| } | |
| /* | |
| * Write to PWM register, which determines the duty cycle of the | |
| * output. LED is OFF when the count is less than the value of this | |
| * register, and ON when it is greater. If PWMx == 0, LED is always OFF. | |
| * | |
| * Duty cycle is (256 - PWMx) / 256 | |
| */ | |
| static int pca955x_write_pwm(struct pca955x *pca955x, int n, u8 val) | |
| { | |
| u8 cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + 1 + (2 * n); | |
| int ret; | |
| ret = i2c_smbus_write_byte_data(pca955x->client, cmd, val); | |
| if (ret < 0) | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", __func__, n, | |
| val, ret); | |
| return ret; | |
| } | |
| /* | |
| * Write to LED selector register, which determines the source that | |
| * drives the LED output. | |
| */ | |
| static int pca955x_write_ls(struct pca955x *pca955x, int n, u8 val) | |
| { | |
| u8 cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + 4 + n; | |
| int ret; | |
| ret = i2c_smbus_write_byte_data(pca955x->client, cmd, val); | |
| if (ret < 0) | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", __func__, n, | |
| val, ret); | |
| return ret; | |
| } | |
| /* | |
| * Read the LED selector register, which determines the source that | |
| * drives the LED output. | |
| */ | |
| static int pca955x_read_ls(struct pca955x *pca955x, int n, u8 *val) | |
| { | |
| u8 cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + 4 + n; | |
| int ret; | |
| ret = i2c_smbus_read_byte_data(pca955x->client, cmd); | |
| if (ret < 0) { | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, err %d\n", __func__, n, ret); | |
| return ret; | |
| } | |
| *val = (u8)ret; | |
| return 0; | |
| } | |
| static int pca955x_read_pwm(struct pca955x *pca955x, int n, u8 *val) | |
| { | |
| u8 cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + 1 + (2 * n); | |
| int ret; | |
| ret = i2c_smbus_read_byte_data(pca955x->client, cmd); | |
| if (ret < 0) { | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, err %d\n", __func__, n, ret); | |
| return ret; | |
| } | |
| *val = (u8)ret; | |
| return 0; | |
| } | |
| static int pca955x_read_psc(struct pca955x *pca955x, int n, u8 *val) | |
| { | |
| int ret; | |
| u8 cmd; | |
| cmd = pca955x_num_input_regs(pca955x->chipdef->bits) + (2 * n); | |
| ret = i2c_smbus_read_byte_data(pca955x->client, cmd); | |
| if (ret < 0) { | |
| dev_err(&pca955x->client->dev, "%s: reg 0x%x, err %d\n", __func__, n, ret); | |
| return ret; | |
| } | |
| *val = (u8)ret; | |
| return 0; | |
| } | |
| static enum led_brightness pca955x_led_get(struct led_classdev *led_cdev) | |
| { | |
| struct pca955x_led *pca955x_led = led_to_pca955x(led_cdev); | |
| struct pca955x *pca955x = pca955x_led->pca955x; | |
| u8 ls, pwm; | |
| int ret; | |
| ret = pca955x_read_ls(pca955x, pca955x_led->led_num / 4, &ls); | |
| if (ret) | |
| return ret; | |
| switch (pca955x_ledstate(ls, pca955x_led->led_num % 4)) { | |
| case PCA955X_LS_LED_ON: | |
| case PCA955X_LS_BLINK0: | |
| ret = LED_FULL; | |
| break; | |
| case PCA955X_LS_LED_OFF: | |
| ret = LED_OFF; | |
| break; | |
| case PCA955X_LS_BLINK1: | |
| ret = pca955x_read_pwm(pca955x, 1, &pwm); | |
| if (ret) | |
| return ret; | |
| ret = 255 - pwm; | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int pca955x_led_set(struct led_classdev *led_cdev, | |
| enum led_brightness value) | |
| { | |
| struct pca955x_led *pca955x_led = led_to_pca955x(led_cdev); | |
| struct pca955x *pca955x = pca955x_led->pca955x; | |
| int reg = pca955x_led->led_num / 4; | |
| int bit = pca955x_led->led_num % 4; | |
| u8 ls; | |
| int ret; | |
| mutex_lock(&pca955x->lock); | |
| ret = pca955x_read_ls(pca955x, reg, &ls); | |
| if (ret) | |
| goto out; | |
| if (test_bit(pca955x_led->led_num, &pca955x->active_blink)) { | |
| if (value == LED_OFF) { | |
| clear_bit(pca955x_led->led_num, &pca955x->active_blink); | |
| ls = pca955x_ledsel(ls, bit, PCA955X_LS_LED_OFF); | |
| } else { | |
| /* No variable brightness for blinking LEDs */ | |
| goto out; | |
| } | |
| } else { | |
| switch (value) { | |
| case LED_FULL: | |
| ls = pca955x_ledsel(ls, bit, PCA955X_LS_LED_ON); | |
| break; | |
| case LED_OFF: | |
| ls = pca955x_ledsel(ls, bit, PCA955X_LS_LED_OFF); | |
| break; | |
| default: | |
| /* | |
| * Use PWM1 for all other values. This has the unwanted | |
| * side effect of making all LEDs on the chip share the | |
| * same brightness level if set to a value other than | |
| * OFF or FULL. But, this is probably better than just | |
| * turning off for all other values. | |
| */ | |
| ret = pca955x_write_pwm(pca955x, 1, 255 - value); | |
| if (ret) | |
| goto out; | |
| ls = pca955x_ledsel(ls, bit, PCA955X_LS_BLINK1); | |
| break; | |
| } | |
| } | |
| ret = pca955x_write_ls(pca955x, reg, ls); | |
| out: | |
| mutex_unlock(&pca955x->lock); | |
| return ret; | |
| } | |
| static u8 pca955x_period_to_psc(struct pca955x *pca955x, unsigned long period) | |
| { | |
| /* psc register value = (blink period * coeff) - 1 */ | |
| period *= pca955x->chipdef->blink_div; | |
| period /= MSEC_PER_SEC; | |
| period -= 1; | |
| return period; | |
| } | |
| static unsigned long pca955x_psc_to_period(struct pca955x *pca955x, u8 psc) | |
| { | |
| unsigned long period = psc; | |
| /* blink period = (psc register value + 1) / coeff */ | |
| period += 1; | |
| period *= MSEC_PER_SEC; | |
| period /= pca955x->chipdef->blink_div; | |
| return period; | |
| } | |
| static int pca955x_led_blink(struct led_classdev *led_cdev, | |
| unsigned long *delay_on, unsigned long *delay_off) | |
| { | |
| struct pca955x_led *pca955x_led = led_to_pca955x(led_cdev); | |
| struct pca955x *pca955x = pca955x_led->pca955x; | |
| unsigned long period = *delay_on + *delay_off; | |
| int ret = 0; | |
| mutex_lock(&pca955x->lock); | |
| if (period) { | |
| if (*delay_on != *delay_off) { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| if (period < pca955x_psc_to_period(pca955x, 0) || | |
| period > pca955x_psc_to_period(pca955x, 0xff)) { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| } else { | |
| period = pca955x->active_blink ? pca955x->blink_period : | |
| PCA955X_BLINK_DEFAULT_MS; | |
| } | |
| if (!pca955x->active_blink || | |
| pca955x->active_blink == BIT(pca955x_led->led_num) || | |
| pca955x->blink_period == period) { | |
| u8 psc = pca955x_period_to_psc(pca955x, period); | |
| if (!test_and_set_bit(pca955x_led->led_num, | |
| &pca955x->active_blink)) { | |
| u8 ls; | |
| int reg = pca955x_led->led_num / 4; | |
| int bit = pca955x_led->led_num % 4; | |
| ret = pca955x_read_ls(pca955x, reg, &ls); | |
| if (ret) | |
| goto out; | |
| ls = pca955x_ledsel(ls, bit, PCA955X_LS_BLINK0); | |
| ret = pca955x_write_ls(pca955x, reg, ls); | |
| if (ret) | |
| goto out; | |
| /* | |
| * Force 50% duty cycle to maintain the specified | |
| * blink rate. | |
| */ | |
| ret = pca955x_write_pwm(pca955x, 0, 128); | |
| if (ret) | |
| goto out; | |
| } | |
| if (pca955x->blink_period != period) { | |
| pca955x->blink_period = period; | |
| ret = pca955x_write_psc(pca955x, 0, psc); | |
| if (ret) | |
| goto out; | |
| } | |
| period = pca955x_psc_to_period(pca955x, psc); | |
| period /= 2; | |
| *delay_on = period; | |
| *delay_off = period; | |
| } else { | |
| ret = -EBUSY; | |
| } | |
| out: | |
| mutex_unlock(&pca955x->lock); | |
| return ret; | |
| } | |
| #ifdef CONFIG_LEDS_PCA955X_GPIO | |
| /* | |
| * Read the INPUT register, which contains the state of LEDs. | |
| */ | |
| static int pca955x_read_input(struct i2c_client *client, int n, u8 *val) | |
| { | |
| int ret = i2c_smbus_read_byte_data(client, n); | |
| if (ret < 0) { | |
| dev_err(&client->dev, "%s: reg 0x%x, err %d\n", | |
| __func__, n, ret); | |
| return ret; | |
| } | |
| *val = (u8)ret; | |
| return 0; | |
| } | |
| static int pca955x_gpio_request_pin(struct gpio_chip *gc, unsigned int offset) | |
| { | |
| struct pca955x *pca955x = gpiochip_get_data(gc); | |
| return test_and_set_bit(offset, &pca955x->active_pins) ? -EBUSY : 0; | |
| } | |
| static void pca955x_gpio_free_pin(struct gpio_chip *gc, unsigned int offset) | |
| { | |
| struct pca955x *pca955x = gpiochip_get_data(gc); | |
| clear_bit(offset, &pca955x->active_pins); | |
| } | |
| static int pca955x_set_value(struct gpio_chip *gc, unsigned int offset, | |
| int val) | |
| { | |
| struct pca955x *pca955x = gpiochip_get_data(gc); | |
| struct pca955x_led *led = &pca955x->leds[offset]; | |
| if (val) | |
| return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_HIGH); | |
| return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_LOW); | |
| } | |
| static int pca955x_gpio_set_value(struct gpio_chip *gc, unsigned int offset, | |
| int val) | |
| { | |
| return pca955x_set_value(gc, offset, val); | |
| } | |
| static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset) | |
| { | |
| struct pca955x *pca955x = gpiochip_get_data(gc); | |
| struct pca955x_led *led = &pca955x->leds[offset]; | |
| u8 reg = 0; | |
| /* There is nothing we can do about errors */ | |
| pca955x_read_input(pca955x->client, led->led_num / 8, ®); | |
| return !!(reg & (1 << (led->led_num % 8))); | |
| } | |
| static int pca955x_gpio_direction_input(struct gpio_chip *gc, | |
| unsigned int offset) | |
| { | |
| struct pca955x *pca955x = gpiochip_get_data(gc); | |
| struct pca955x_led *led = &pca955x->leds[offset]; | |
| /* To use as input ensure pin is not driven. */ | |
| return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_INPUT); | |
| } | |
| static int pca955x_gpio_direction_output(struct gpio_chip *gc, | |
| unsigned int offset, int val) | |
| { | |
| return pca955x_set_value(gc, offset, val); | |
| } | |
| #endif /* CONFIG_LEDS_PCA955X_GPIO */ | |
| static struct pca955x_platform_data * | |
| pca955x_get_pdata(struct i2c_client *client, const struct pca955x_chipdef *chip) | |
| { | |
| struct pca955x_platform_data *pdata; | |
| struct pca955x_led *led; | |
| struct fwnode_handle *child; | |
| int count; | |
| count = device_get_child_node_count(&client->dev); | |
| if (count > chip->bits) | |
| return ERR_PTR(-ENODEV); | |
| pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); | |
| if (!pdata) | |
| return ERR_PTR(-ENOMEM); | |
| pdata->leds = devm_kcalloc(&client->dev, | |
| chip->bits, sizeof(struct pca955x_led), | |
| GFP_KERNEL); | |
| if (!pdata->leds) | |
| return ERR_PTR(-ENOMEM); | |
| device_for_each_child_node(&client->dev, child) { | |
| u32 reg; | |
| int res; | |
| res = fwnode_property_read_u32(child, "reg", ®); | |
| if ((res != 0) || (reg >= chip->bits)) | |
| continue; | |
| led = &pdata->leds[reg]; | |
| led->type = PCA955X_TYPE_LED; | |
| led->fwnode = child; | |
| led->default_state = led_init_default_state_get(child); | |
| fwnode_property_read_u32(child, "type", &led->type); | |
| } | |
| pdata->num_leds = chip->bits; | |
| return pdata; | |
| } | |
| static int pca955x_probe(struct i2c_client *client) | |
| { | |
| struct pca955x *pca955x; | |
| struct pca955x_led *pca955x_led; | |
| const struct pca955x_chipdef *chip; | |
| struct led_classdev *led; | |
| struct led_init_data init_data; | |
| struct i2c_adapter *adapter; | |
| u8 i, nls, psc0; | |
| u8 ls1[4]; | |
| u8 ls2[4]; | |
| struct pca955x_platform_data *pdata; | |
| bool keep_psc0 = false; | |
| bool set_default_label = false; | |
| char default_label[4]; | |
| int bit, err, reg; | |
| chip = i2c_get_match_data(client); | |
| if (!chip) | |
| return dev_err_probe(&client->dev, -ENODEV, "unknown chip\n"); | |
| adapter = client->adapter; | |
| pdata = dev_get_platdata(&client->dev); | |
| if (!pdata) { | |
| pdata = pca955x_get_pdata(client, chip); | |
| if (IS_ERR(pdata)) | |
| return PTR_ERR(pdata); | |
| } | |
| /* Make sure the slave address / chip type combo given is possible */ | |
| if ((client->addr & ~((1 << chip->slv_addr_shift) - 1)) != | |
| chip->slv_addr) { | |
| dev_err(&client->dev, "invalid slave address %02x\n", | |
| client->addr); | |
| return -ENODEV; | |
| } | |
| dev_info(&client->dev, "Using %s %u-bit LED driver at slave address 0x%02x\n", | |
| client->name, chip->bits, client->addr); | |
| if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) | |
| return -EIO; | |
| if (pdata->num_leds != chip->bits) { | |
| dev_err(&client->dev, | |
| "board info claims %d LEDs on a %u-bit chip\n", | |
| pdata->num_leds, chip->bits); | |
| return -ENODEV; | |
| } | |
| pca955x = devm_kzalloc(&client->dev, sizeof(*pca955x), GFP_KERNEL); | |
| if (!pca955x) | |
| return -ENOMEM; | |
| pca955x->leds = devm_kcalloc(&client->dev, chip->bits, | |
| sizeof(*pca955x_led), GFP_KERNEL); | |
| if (!pca955x->leds) | |
| return -ENOMEM; | |
| i2c_set_clientdata(client, pca955x); | |
| mutex_init(&pca955x->lock); | |
| pca955x->client = client; | |
| pca955x->chipdef = chip; | |
| pca955x->blink_period = PCA955X_BLINK_DEFAULT_MS; | |
| init_data.devname_mandatory = false; | |
| init_data.devicename = "pca955x"; | |
| nls = pca955x_num_led_regs(chip->bits); | |
| /* Use auto-increment feature to read all the LED selectors at once. */ | |
| err = i2c_smbus_read_i2c_block_data(client, | |
| 0x10 | (pca955x_num_input_regs(chip->bits) + 4), nls, | |
| ls1); | |
| if (err < 0) | |
| return err; | |
| for (i = 0; i < nls; i++) | |
| ls2[i] = ls1[i]; | |
| for (i = 0; i < chip->bits; i++) { | |
| pca955x_led = &pca955x->leds[i]; | |
| pca955x_led->led_num = i; | |
| pca955x_led->pca955x = pca955x; | |
| pca955x_led->type = pdata->leds[i].type; | |
| switch (pca955x_led->type) { | |
| case PCA955X_TYPE_NONE: | |
| case PCA955X_TYPE_GPIO: | |
| break; | |
| case PCA955X_TYPE_LED: | |
| bit = i % 4; | |
| reg = i / 4; | |
| led = &pca955x_led->led_cdev; | |
| led->brightness_set_blocking = pca955x_led_set; | |
| led->brightness_get = pca955x_led_get; | |
| led->blink_set = pca955x_led_blink; | |
| if (pdata->leds[i].default_state == LEDS_DEFSTATE_OFF) | |
| ls2[reg] = pca955x_ledsel(ls2[reg], bit, PCA955X_LS_LED_OFF); | |
| else if (pdata->leds[i].default_state == LEDS_DEFSTATE_ON) | |
| ls2[reg] = pca955x_ledsel(ls2[reg], bit, PCA955X_LS_LED_ON); | |
| else if (pca955x_ledstate(ls2[reg], bit) == PCA955X_LS_BLINK0) { | |
| keep_psc0 = true; | |
| set_bit(i, &pca955x->active_blink); | |
| } | |
| init_data.fwnode = pdata->leds[i].fwnode; | |
| if (is_of_node(init_data.fwnode)) { | |
| if (to_of_node(init_data.fwnode)->name[0] == | |
| '\0') | |
| set_default_label = true; | |
| else | |
| set_default_label = false; | |
| } else { | |
| set_default_label = true; | |
| } | |
| if (set_default_label) { | |
| snprintf(default_label, sizeof(default_label), "%hhu", i); | |
| init_data.default_label = default_label; | |
| } else { | |
| init_data.default_label = NULL; | |
| } | |
| err = devm_led_classdev_register_ext(&client->dev, led, | |
| &init_data); | |
| if (err) | |
| return err; | |
| set_bit(i, &pca955x->active_pins); | |
| } | |
| } | |
| for (i = 0; i < nls; i++) { | |
| if (ls1[i] != ls2[i]) { | |
| err = pca955x_write_ls(pca955x, i, ls2[i]); | |
| if (err) | |
| return err; | |
| } | |
| } | |
| if (keep_psc0) { | |
| err = pca955x_read_psc(pca955x, 0, &psc0); | |
| } else { | |
| psc0 = pca955x_period_to_psc(pca955x, pca955x->blink_period); | |
| err = pca955x_write_psc(pca955x, 0, psc0); | |
| } | |
| if (err) | |
| return err; | |
| pca955x->blink_period = pca955x_psc_to_period(pca955x, psc0); | |
| /* Set PWM1 to fast frequency so we do not see flashing */ | |
| err = pca955x_write_psc(pca955x, 1, 0); | |
| if (err) | |
| return err; | |
| #ifdef CONFIG_LEDS_PCA955X_GPIO | |
| pca955x->gpio.label = "gpio-pca955x"; | |
| pca955x->gpio.direction_input = pca955x_gpio_direction_input; | |
| pca955x->gpio.direction_output = pca955x_gpio_direction_output; | |
| pca955x->gpio.set = pca955x_gpio_set_value; | |
| pca955x->gpio.get = pca955x_gpio_get_value; | |
| pca955x->gpio.request = pca955x_gpio_request_pin; | |
| pca955x->gpio.free = pca955x_gpio_free_pin; | |
| pca955x->gpio.can_sleep = 1; | |
| pca955x->gpio.base = -1; | |
| pca955x->gpio.ngpio = chip->bits; | |
| pca955x->gpio.parent = &client->dev; | |
| pca955x->gpio.owner = THIS_MODULE; | |
| err = devm_gpiochip_add_data(&client->dev, &pca955x->gpio, | |
| pca955x); | |
| if (err) { | |
| /* Use data->gpio.dev as a flag for freeing gpiochip */ | |
| pca955x->gpio.parent = NULL; | |
| dev_warn(&client->dev, "could not add gpiochip\n"); | |
| return err; | |
| } | |
| dev_info(&client->dev, "gpios %i...%i\n", | |
| pca955x->gpio.base, pca955x->gpio.base + | |
| pca955x->gpio.ngpio - 1); | |
| #endif | |
| return 0; | |
| } | |
| static const struct i2c_device_id pca955x_id[] = { | |
| { .name = "pca9550", .driver_data = (kernel_ulong_t)&pca955x_chipdefs[pca9550] }, | |
| { .name = "pca9551", .driver_data = (kernel_ulong_t)&pca955x_chipdefs[pca9551] }, | |
| { .name = "pca9552", .driver_data = (kernel_ulong_t)&pca955x_chipdefs[pca9552] }, | |
| { .name = "ibm-pca9552", .driver_data = (kernel_ulong_t)&pca955x_chipdefs[ibm_pca9552] }, | |
| { .name = "pca9553", .driver_data = (kernel_ulong_t)&pca955x_chipdefs[pca9553] }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, pca955x_id); | |
| static const struct of_device_id of_pca955x_match[] = { | |
| { .compatible = "nxp,pca9550", .data = &pca955x_chipdefs[pca9550] }, | |
| { .compatible = "nxp,pca9551", .data = &pca955x_chipdefs[pca9551] }, | |
| { .compatible = "nxp,pca9552", .data = &pca955x_chipdefs[pca9552] }, | |
| { .compatible = "ibm,pca9552", .data = &pca955x_chipdefs[ibm_pca9552] }, | |
| { .compatible = "nxp,pca9553", .data = &pca955x_chipdefs[pca9553] }, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(of, of_pca955x_match); | |
| static struct i2c_driver pca955x_driver = { | |
| .driver = { | |
| .name = "leds-pca955x", | |
| .of_match_table = of_pca955x_match, | |
| }, | |
| .probe = pca955x_probe, | |
| .id_table = pca955x_id, | |
| }; | |
| module_i2c_driver(pca955x_driver); | |
| MODULE_AUTHOR("Nate Case <ncase@xes-inc.com>"); | |
| MODULE_DESCRIPTION("PCA955x LED driver"); | |
| MODULE_LICENSE("GPL v2"); |