| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/err.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/irqchip.h> | |
| #include <linux/irqdomain.h> | |
| #include <linux/io.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/soc/qcom/irq.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/slab.h> | |
| #include <linux/types.h> | |
| #include <linux/firmware/qcom/qcom_scm.h> | |
| #define PDC_MAX_IRQS 256 | |
| #define IRQ_ENABLE_BANK_MAX BITS_TO_BYTES(PDC_MAX_IRQS) | |
| #define IRQ_ENABLE_BANK_INDEX_MASK GENMASK(31, 5) | |
| #define IRQ_ENABLE_BANK_BIT_MASK GENMASK(4, 0) | |
| /* Secure DRV register to configure the PDC mode via qcom_scm_io_writel() */ | |
| #define PDC_GPIO_INT_CTL_ENABLE 0xb2045e8 | |
| #define PDC_PASS_THROUGH_MODE 0x0 | |
| #define PDC_SECONDARY_MODE 0x1 | |
| #define PDC_DRV_SIZE 0x10000 | |
| #define PDC_VERSION_REG 0x1000 | |
| #define PDC_VERSION_MAJOR GENMASK(23, 16) | |
| #define PDC_VERSION_MINOR GENMASK(15, 8) | |
| #define PDC_VERSION_STEP GENMASK(7, 0) | |
| #define PDC_VERSION(maj, min, step) (FIELD_PREP(PDC_VERSION_MAJOR, (maj)) | \ | |
| FIELD_PREP(PDC_VERSION_MINOR, (min)) | \ | |
| FIELD_PREP(PDC_VERSION_STEP, (step))) | |
| /* Notable PDC versions */ | |
| #define PDC_VERSION_3_2 PDC_VERSION(3, 2, 0) | |
| #define PDC_VERSION_3_0 PDC_VERSION(3, 0, 0) | |
| #define PDC_VERSION_2_7 PDC_VERSION(2, 7, 0) | |
| /* | |
| * PDC Hardware registers layout per version: | |
| * | |
| * IRQ_ENABLE_BANK[b], b = 0....BITS_TO_BYTES(PDC_MAX_IRQS) | |
| * IRQ_CFG[n], n = 0....PDC_MAX_IRQS | |
| * | |
| * +---------------------------------------------------------------+ | |
| * | v2.7 | v3.0 | v3.2 | | |
| * |---------------------------------------------------------------| | |
| * | BASE | BASE | BASE | | |
| * |---------------------------------------------------------------| | |
| * | | | |
| * | IRQ_ENABLE_BANK | IRQ_ENABLE_BANK | NA | | |
| * |---------------------------------------------------------------| | |
| * | IRQ_CFG | IRQ_CFG | IRQ_CFG | | |
| * | | | | | |
| * | | | [31:6] Unused | | |
| * | | [31:5] Unused | [5] GPIO_STATUS | | |
| * | | [4] GPIO_STATUS| [4] GPIO_MASK | | |
| * | [31:3] Unused | [3] GPIO_MASK | [3] IRQ_ENABLE | | |
| * | [0:2] Type | [0:2] Type | [0:2] Type | | |
| * |---------------------------------------------------------------| | |
| * | IRQ_PARAM | IRQ_PARAM | IRQ_PARAM | | |
| * | | | | |
| * | [15:8] NUM_GPIO | [15:8] NUM_GPIO | [15:8] NUM_GPIO | | |
| * | [7:0] NUM_SPI | [7:0] NUM_SPI | [7:0] NUM_SPI | | |
| * +---------------------------------------------------------------+ | |
| */ | |
| /** | |
| * struct pdc_regs: PDC registers location | |
| * | |
| * @irq_en_reg: IRQ_ENABLE_BANK register location | |
| * @irq_cfg_reg: IRQ_CFG register location | |
| * @irq_param_reg: IRQ_PARAM register location | |
| */ | |
| struct pdc_regs { | |
| u32 irq_en_reg; | |
| u32 irq_cfg_reg; | |
| u32 irq_param_reg; | |
| }; | |
| /** | |
| * struct pdc_irq_cfg: bit fields for PDC IRQ_CFG register | |
| * | |
| * @gpio_irq_sts: bit number for GPIO_STATUS field | |
| * @gpio_irq_mask: bit number for GPIO_MASK field | |
| * @irq_enable: bit number for IRQ_ENABLE field | |
| * @irq_type: GENMASK for IRQ_TYPE field | |
| */ | |
| struct pdc_irq_cfg { | |
| u32 gpio_irq_sts; | |
| u32 gpio_irq_mask; | |
| u32 irq_enable; | |
| u32 irq_type; | |
| }; | |
| /** | |
| * struct pdc_desc: PDC driver state | |
| * | |
| * @base: PDC base register for DRV2 / HLOS | |
| * @prev_base: PDC DRV1 base, applicable only for x1e RTL bug. | |
| * @version: PDC version | |
| * @num_spis: Total number of direct SPI interrupts | |
| * @region: PDC interrupt continuous range | |
| * @region_cnt: Total PDC ranges | |
| * @mode: PDC_PASS_THROUGH_MODE or PDC_SECONDARY_MODE | |
| * @x1e_quirk: x1e H/W Bug handling | |
| * @lock: lock for IRQ_ENABLE_BANK protection | |
| * @regs: PDC regs (IRQ_ENABLE_BANK and IRQ_CFG) | |
| * @cfg_fields: Fields of IRQ_CFG reg | |
| * @enable_intr: pointer to enable function based on PDC version | |
| * @unmask_gpio: pointer to GPIO irq unmask function | |
| * @clear_gpio: pointer to GPIO irq clear function | |
| */ | |
| struct pdc_desc { | |
| void __iomem *base; | |
| void __iomem *prev_base; | |
| u32 version; | |
| u32 num_spis; | |
| struct pdc_pin_region *region; | |
| int region_cnt; | |
| bool x1e_quirk; | |
| u8 mode; | |
| raw_spinlock_t lock; | |
| const struct pdc_regs *regs; | |
| const struct pdc_irq_cfg *cfg_fields; | |
| void (*enable_intr)(int pin_out, bool on); | |
| void (*unmask_gpio)(int pin_out, bool on); | |
| void (*clear_gpio)(int pin_out); | |
| }; | |
| static const struct pdc_regs pdc_v3_2 = { | |
| .irq_cfg_reg = 0x110, | |
| .irq_param_reg = 0x100c, | |
| }; | |
| static const struct pdc_irq_cfg pdc_cfg_v3_2 = { | |
| .gpio_irq_sts = 5, | |
| .gpio_irq_mask = 4, | |
| .irq_enable = 3, | |
| .irq_type = GENMASK(2, 0), | |
| }; | |
| static const struct pdc_regs pdc_v3_0 = { | |
| .irq_en_reg = 0x10, | |
| .irq_cfg_reg = 0x110, | |
| .irq_param_reg = 0x100c, | |
| }; | |
| static const struct pdc_irq_cfg pdc_cfg_v3_0 = { | |
| .gpio_irq_sts = 4, | |
| .gpio_irq_mask = 3, | |
| .irq_type = GENMASK(2, 0), | |
| }; | |
| static const struct pdc_regs pdc_v2_7 = { | |
| .irq_en_reg = 0x10, | |
| .irq_cfg_reg = 0x110, | |
| .irq_param_reg = 0x100c, | |
| }; | |
| static const struct pdc_irq_cfg pdc_cfg_v2_7 = { | |
| .irq_type = GENMASK(2, 0), | |
| }; | |
| struct pdc_pin_region { | |
| u32 pin_base; | |
| u32 parent_base; | |
| u32 cnt; | |
| }; | |
| #define pin_to_hwirq(r, p) ((r)->parent_base + (p) - (r)->pin_base) | |
| static struct pdc_desc *pdc; | |
| static void pdc_base_reg_write(void __iomem *base, int reg, u32 i, u32 val) | |
| { | |
| writel_relaxed(val, base + reg + i * sizeof(u32)); | |
| } | |
| static void pdc_reg_write(int reg, u32 i, u32 val) | |
| { | |
| pdc_base_reg_write(pdc->base, reg, i, val); | |
| } | |
| static u32 pdc_reg_read(int reg, u32 i) | |
| { | |
| return readl_relaxed(pdc->base + reg + i * sizeof(u32)); | |
| } | |
| static inline bool pdc_pin_is_gpio(int pin_out) | |
| { | |
| /* | |
| * PDC allocates direct SPIs at the beginning and | |
| * all GPIOs as SPIs are allocated after direct SPIs. | |
| */ | |
| return pin_out >= pdc->num_spis; | |
| } | |
| static void pdc_x1e_irq_enable_write(u32 bank, u32 enable) | |
| { | |
| void __iomem *base; | |
| /* Remap the write access to work around a hardware bug on X1E */ | |
| switch (bank) { | |
| case 0 ... 1: | |
| /* Use previous DRV (client) region and shift to bank 3-4 */ | |
| base = pdc->prev_base; | |
| bank += 3; | |
| break; | |
| case 2 ... 4: | |
| /* Use our own region and shift to bank 0-2 */ | |
| base = pdc->base; | |
| bank -= 2; | |
| break; | |
| case 5: | |
| /* No fixup required for bank 5 */ | |
| base = pdc->base; | |
| break; | |
| default: | |
| WARN_ON(1); | |
| return; | |
| } | |
| pdc_base_reg_write(base, pdc->regs->irq_en_reg, bank, enable); | |
| } | |
| static void pdc_enable_intr_bank(int pin_out, bool on) | |
| { | |
| unsigned long enable; | |
| u32 index, mask; | |
| index = FIELD_GET(IRQ_ENABLE_BANK_INDEX_MASK, pin_out); | |
| mask = FIELD_GET(IRQ_ENABLE_BANK_BIT_MASK, pin_out); | |
| guard(raw_spinlock_irqsave)(&pdc->lock); | |
| enable = pdc_reg_read(pdc->regs->irq_en_reg, index); | |
| __assign_bit(mask, &enable, on); | |
| if (pdc->x1e_quirk) | |
| pdc_x1e_irq_enable_write(index, enable); | |
| else | |
| pdc_reg_write(pdc->regs->irq_en_reg, index, enable); | |
| } | |
| static void pdc_clear_gpio_cfg(int pin_out) | |
| { | |
| unsigned long gpio_sts; | |
| gpio_sts = pdc_reg_read(pdc->regs->irq_cfg_reg, pin_out); | |
| __clear_bit(pdc->cfg_fields->gpio_irq_sts, &gpio_sts); | |
| pdc_reg_write(pdc->regs->irq_cfg_reg, pin_out, gpio_sts); | |
| } | |
| static void pdc_unmask_gpio_cfg(int pin_out, bool unmask) | |
| { | |
| unsigned long gpio_mask; | |
| gpio_mask = pdc_reg_read(pdc->regs->irq_cfg_reg, pin_out); | |
| __assign_bit(pdc->cfg_fields->gpio_irq_mask, &gpio_mask, !unmask); | |
| pdc_reg_write(pdc->regs->irq_cfg_reg, pin_out, gpio_mask); | |
| } | |
| static void pdc_enable_intr_cfg(int pin_out, bool on) | |
| { | |
| unsigned long enable = pdc_reg_read(pdc->regs->irq_cfg_reg, pin_out); | |
| __assign_bit(pdc->cfg_fields->irq_enable, &enable, on); | |
| pdc_reg_write(pdc->regs->irq_cfg_reg, pin_out, enable); | |
| } | |
| static void qcom_pdc_gic_secondary_disable(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, false); | |
| pdc->unmask_gpio(d->hwirq, false); | |
| irq_chip_disable_parent(d); | |
| } | |
| static void qcom_pdc_gic_disable(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, false); | |
| irq_chip_disable_parent(d); | |
| } | |
| static void qcom_pdc_gic_enable(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, true); | |
| irq_chip_enable_parent(d); | |
| } | |
| static void qcom_pdc_gic_secondary_enable(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, true); | |
| pdc->unmask_gpio(d->hwirq, true); | |
| irq_chip_enable_parent(d); | |
| } | |
| static void qcom_pdc_secondary_ack(struct irq_data *d) | |
| { | |
| if (!irqd_is_level_type(d)) | |
| pdc->clear_gpio(d->hwirq); | |
| } | |
| static void qcom_pdc_gic_secondary_eoi(struct irq_data *d) | |
| { | |
| if (irqd_is_level_type(d)) | |
| pdc->clear_gpio(d->hwirq); | |
| irq_chip_eoi_parent(d); | |
| } | |
| static void qcom_pdc_secondary_mask(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, false); | |
| pdc->unmask_gpio(d->hwirq, false); | |
| irq_chip_mask_parent(d); | |
| } | |
| static void qcom_pdc_secondary_unmask(struct irq_data *d) | |
| { | |
| pdc->enable_intr(d->hwirq, true); | |
| pdc->unmask_gpio(d->hwirq, true); | |
| irq_chip_unmask_parent(d); | |
| } | |
| /* | |
| * GIC does not handle falling edge or active low. To allow falling edge and | |
| * active low interrupts to be handled at GIC, PDC has an inverter that inverts | |
| * falling edge into a rising edge and active low into an active high. | |
| * For the inverter to work, the polarity bit in the IRQ_CONFIG register has to | |
| * set as per the table below. | |
| * Level sensitive active low LOW | |
| * Rising edge sensitive NOT USED | |
| * Falling edge sensitive LOW | |
| * Dual Edge sensitive NOT USED | |
| * Level sensitive active High HIGH | |
| * Falling Edge sensitive NOT USED | |
| * Rising edge sensitive HIGH | |
| * Dual Edge sensitive HIGH | |
| */ | |
| enum pdc_irq_config_bits { | |
| PDC_LEVEL_LOW = 0b000, | |
| PDC_EDGE_FALLING = 0b010, | |
| PDC_LEVEL_HIGH = 0b100, | |
| PDC_EDGE_RISING = 0b110, | |
| PDC_EDGE_DUAL = 0b111, | |
| }; | |
| /** | |
| * qcom_pdc_gic_set_type: Configure PDC for the interrupt | |
| * | |
| * @d: the interrupt data | |
| * @type: the interrupt type | |
| * | |
| * If @type is edge triggered, forward that as rising edge as PDC | |
| * takes care of converting all edge types to rising edge signal | |
| * If @type is level, then forward that as level high as PDC | |
| * takes care of converting all level types to level high signal | |
| */ | |
| static int qcom_pdc_gic_set_type(struct irq_data *d, unsigned int type) | |
| { | |
| enum pdc_irq_config_bits old_pdc_type; | |
| enum pdc_irq_config_bits pdc_type; | |
| int ret; | |
| switch (type) { | |
| case IRQ_TYPE_EDGE_RISING: | |
| pdc_type = PDC_EDGE_RISING; | |
| break; | |
| case IRQ_TYPE_EDGE_FALLING: | |
| pdc_type = PDC_EDGE_FALLING; | |
| type = IRQ_TYPE_EDGE_RISING; | |
| break; | |
| case IRQ_TYPE_EDGE_BOTH: | |
| pdc_type = PDC_EDGE_DUAL; | |
| type = IRQ_TYPE_EDGE_RISING; | |
| break; | |
| case IRQ_TYPE_LEVEL_HIGH: | |
| pdc_type = PDC_LEVEL_HIGH; | |
| break; | |
| case IRQ_TYPE_LEVEL_LOW: | |
| pdc_type = PDC_LEVEL_LOW; | |
| type = IRQ_TYPE_LEVEL_HIGH; | |
| break; | |
| default: | |
| WARN_ON(1); | |
| return -EINVAL; | |
| } | |
| old_pdc_type = pdc_reg_read(pdc->regs->irq_cfg_reg, d->hwirq); | |
| pdc_type |= (old_pdc_type & ~pdc->cfg_fields->irq_type); | |
| pdc_reg_write(pdc->regs->irq_cfg_reg, d->hwirq, pdc_type); | |
| ret = irq_chip_set_type_parent(d, type); | |
| if (ret) | |
| return ret; | |
| /* | |
| * When we change types the PDC can give a phantom interrupt. | |
| * Clear it. Specifically the phantom shows up when reconfiguring | |
| * polarity of interrupt without changing the state of the signal | |
| * but let's be consistent and clear it always. | |
| * | |
| * Doing this works because we have IRQCHIP_SET_TYPE_MASKED so the | |
| * interrupt will be cleared before the rest of the system sees it. | |
| */ | |
| if (old_pdc_type != pdc_type) | |
| irq_chip_set_parent_state(d, IRQCHIP_STATE_PENDING, false); | |
| return 0; | |
| } | |
| /** | |
| * qcom_pdc_gic_secondary_set_type: Configure PDC for the interrupt in secondary mode | |
| * | |
| * @d: the interrupt data | |
| * @type: the interrupt type | |
| * | |
| * All @type are forwarded as level high type to parent GIC | |
| */ | |
| static int qcom_pdc_gic_secondary_set_type(struct irq_data *d, unsigned int type) | |
| { | |
| enum pdc_irq_config_bits old_pdc_type; | |
| enum pdc_irq_config_bits pdc_type; | |
| int ret; | |
| switch (type) { | |
| case IRQ_TYPE_EDGE_RISING: | |
| pdc_type = PDC_EDGE_RISING; | |
| break; | |
| case IRQ_TYPE_EDGE_FALLING: | |
| pdc_type = PDC_EDGE_FALLING; | |
| break; | |
| case IRQ_TYPE_EDGE_BOTH: | |
| pdc_type = PDC_EDGE_DUAL; | |
| break; | |
| case IRQ_TYPE_LEVEL_HIGH: | |
| pdc_type = PDC_LEVEL_HIGH; | |
| break; | |
| case IRQ_TYPE_LEVEL_LOW: | |
| pdc_type = PDC_LEVEL_LOW; | |
| break; | |
| default: | |
| WARN_ON(1); | |
| return -EINVAL; | |
| } | |
| old_pdc_type = pdc_reg_read(pdc->regs->irq_cfg_reg, d->hwirq); | |
| pdc_type |= (old_pdc_type & ~pdc->cfg_fields->irq_type); | |
| pdc_reg_write(pdc->regs->irq_cfg_reg, d->hwirq, pdc_type); | |
| /* | |
| * PDC forwards GPIOs as level high to GIC in secondary | |
| * mode. Update the type and clear any previously latched | |
| * phantom interrupt at PDC. | |
| */ | |
| type = IRQ_TYPE_LEVEL_HIGH; | |
| pdc->clear_gpio(d->hwirq); | |
| ret = irq_chip_set_type_parent(d, type); | |
| if (ret) | |
| return ret; | |
| /* | |
| * When we change types the PDC can give a phantom interrupt. | |
| * Clear it. Specifically the phantom shows up when reconfiguring | |
| * polarity of interrupt without changing the state of the signal | |
| * but let's be consistent and clear it always. | |
| * | |
| * Doing this works because we have IRQCHIP_SET_TYPE_MASKED so the | |
| * interrupt will be cleared before the rest of the system sees it. | |
| */ | |
| if (old_pdc_type != pdc_type) | |
| irq_chip_set_parent_state(d, IRQCHIP_STATE_PENDING, false); | |
| return 0; | |
| } | |
| static struct irq_chip qcom_pdc_gic_chip = { | |
| .name = "PDC", | |
| .irq_eoi = irq_chip_eoi_parent, | |
| .irq_mask = irq_chip_mask_parent, | |
| .irq_unmask = irq_chip_unmask_parent, | |
| .irq_disable = qcom_pdc_gic_disable, | |
| .irq_enable = qcom_pdc_gic_enable, | |
| .irq_get_irqchip_state = irq_chip_get_parent_state, | |
| .irq_set_irqchip_state = irq_chip_set_parent_state, | |
| .irq_retrigger = irq_chip_retrigger_hierarchy, | |
| .irq_set_type = qcom_pdc_gic_set_type, | |
| .flags = IRQCHIP_MASK_ON_SUSPEND | | |
| IRQCHIP_SET_TYPE_MASKED | | |
| IRQCHIP_SKIP_SET_WAKE | | |
| IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND, | |
| .irq_set_vcpu_affinity = irq_chip_set_vcpu_affinity_parent, | |
| .irq_set_affinity = irq_chip_set_affinity_parent, | |
| }; | |
| static struct irq_chip qcom_pdc_gic_secondary_chip = { | |
| .name = "PDC", | |
| .irq_ack = qcom_pdc_secondary_ack, | |
| .irq_eoi = qcom_pdc_gic_secondary_eoi, | |
| .irq_mask = qcom_pdc_secondary_mask, | |
| .irq_unmask = qcom_pdc_secondary_unmask, | |
| .irq_disable = qcom_pdc_gic_secondary_disable, | |
| .irq_enable = qcom_pdc_gic_secondary_enable, | |
| .irq_get_irqchip_state = irq_chip_get_parent_state, | |
| .irq_set_irqchip_state = irq_chip_set_parent_state, | |
| .irq_retrigger = irq_chip_retrigger_hierarchy, | |
| .irq_set_type = qcom_pdc_gic_secondary_set_type, | |
| .flags = IRQCHIP_MASK_ON_SUSPEND | | |
| IRQCHIP_SET_TYPE_MASKED | | |
| IRQCHIP_SKIP_SET_WAKE | | |
| IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND, | |
| .irq_set_vcpu_affinity = irq_chip_set_vcpu_affinity_parent, | |
| .irq_set_affinity = irq_chip_set_affinity_parent, | |
| }; | |
| static struct pdc_pin_region *get_pin_region(int pin) | |
| { | |
| for (int i = 0; i < pdc->region_cnt; i++) { | |
| if (pin >= pdc->region[i].pin_base && | |
| pin < pdc->region[i].pin_base + pdc->region[i].cnt) | |
| return &pdc->region[i]; | |
| } | |
| return NULL; | |
| } | |
| static int qcom_pdc_alloc(struct irq_domain *domain, unsigned int virq, | |
| unsigned int nr_irqs, void *data) | |
| { | |
| struct irq_fwspec *fwspec = data; | |
| struct irq_fwspec parent_fwspec; | |
| struct pdc_pin_region *region; | |
| irq_hw_number_t hwirq; | |
| unsigned int type; | |
| int ret; | |
| ret = irq_domain_translate_twocell(domain, fwspec, &hwirq, &type); | |
| if (ret) | |
| return ret; | |
| if (hwirq == GPIO_NO_WAKE_IRQ) | |
| return irq_domain_disconnect_hierarchy(domain, virq); | |
| ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq, | |
| &qcom_pdc_gic_chip, NULL); | |
| if (ret) | |
| return ret; | |
| /* | |
| * PDC secondary chip is only set for the GPIO interrupts as SPIs. | |
| * Direct SPI interrupts are still in pass through mode (no latching | |
| * at PDC). | |
| */ | |
| if (pdc->mode == PDC_SECONDARY_MODE && pdc_pin_is_gpio(hwirq)) { | |
| ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq, | |
| &qcom_pdc_gic_secondary_chip, | |
| NULL); | |
| if (ret) | |
| return ret; | |
| /* Secondary mode converts all interrupts to LEVEL HIGH type */ | |
| type = IRQ_TYPE_LEVEL_HIGH; | |
| } else { | |
| ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq, | |
| &qcom_pdc_gic_chip, | |
| NULL); | |
| if (ret) | |
| return ret; | |
| if (type & IRQ_TYPE_EDGE_BOTH) | |
| type = IRQ_TYPE_EDGE_RISING; | |
| if (type & IRQ_TYPE_LEVEL_MASK) | |
| type = IRQ_TYPE_LEVEL_HIGH; | |
| } | |
| region = get_pin_region(hwirq); | |
| if (!region) | |
| return irq_domain_disconnect_hierarchy(domain->parent, virq); | |
| parent_fwspec.fwnode = domain->parent->fwnode; | |
| parent_fwspec.param_count = 3; | |
| parent_fwspec.param[0] = 0; | |
| parent_fwspec.param[1] = pin_to_hwirq(region, hwirq); | |
| parent_fwspec.param[2] = type; | |
| return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &parent_fwspec); | |
| } | |
| static const struct irq_domain_ops qcom_pdc_ops = { | |
| .translate = irq_domain_translate_twocell, | |
| .alloc = qcom_pdc_alloc, | |
| .free = irq_domain_free_irqs_common, | |
| }; | |
| static int pdc_setup_pin_mapping(struct device *dev) | |
| { | |
| struct device_node *np = dev->of_node; | |
| int ret, n; | |
| n = of_property_count_elems_of_size(np, "qcom,pdc-ranges", sizeof(u32)); | |
| if (n <= 0 || n % 3) | |
| return -EINVAL; | |
| pdc->region_cnt = n / 3; | |
| pdc->region = devm_kcalloc(dev, pdc->region_cnt, sizeof(*pdc->region), GFP_KERNEL); | |
| if (!pdc->region) { | |
| pdc->region_cnt = 0; | |
| return -ENOMEM; | |
| } | |
| for (n = 0; n < pdc->region_cnt; n++) { | |
| ret = of_property_read_u32_index(np, "qcom,pdc-ranges", n * 3 + 0, | |
| &pdc->region[n].pin_base); | |
| if (ret) | |
| return ret; | |
| ret = of_property_read_u32_index(np, "qcom,pdc-ranges", n * 3 + 1, | |
| &pdc->region[n].parent_base); | |
| if (ret) | |
| return ret; | |
| ret = of_property_read_u32_index(np, "qcom,pdc-ranges", n * 3 + 2, | |
| &pdc->region[n].cnt); | |
| if (ret) | |
| return ret; | |
| for (int i = 0; i < pdc->region[n].cnt; i++) { | |
| if (pdc_pin_is_gpio(i + pdc->region[n].pin_base) && | |
| pdc->mode == PDC_SECONDARY_MODE) | |
| pdc->clear_gpio(i + pdc->region[n].pin_base); | |
| pdc->enable_intr(i + pdc->region[n].pin_base, false); | |
| } | |
| } | |
| return 0; | |
| } | |
| static int qcom_pdc_probe(struct platform_device *pdev, struct device_node *parent) | |
| { | |
| struct irq_domain *parent_domain, *pdc_domain; | |
| struct device_node *node = pdev->dev.of_node; | |
| struct device *dev = &pdev->dev; | |
| resource_size_t res_size; | |
| struct resource res; | |
| u32 irq_param; | |
| int ret; | |
| /* compat with old sm8150 DT which had very small region for PDC */ | |
| if (of_address_to_resource(node, 0, &res)) | |
| return -EINVAL; | |
| res_size = max_t(resource_size_t, resource_size(&res), PDC_DRV_SIZE); | |
| if (res_size > resource_size(&res)) | |
| pr_warn("%pOF: invalid reg size, please fix DT\n", node); | |
| pdc = devm_kzalloc(dev, sizeof(*pdc), GFP_KERNEL); | |
| if (!pdc) | |
| return -ENOMEM; | |
| pdc->base = devm_ioremap(dev, res.start, res_size); | |
| if (!pdc->base) { | |
| pr_err("%pOF: unable to map PDC registers\n", node); | |
| return -ENXIO; | |
| } | |
| pdc->version = pdc_reg_read(PDC_VERSION_REG, 0); | |
| if (pdc->version >= PDC_VERSION_3_2) { | |
| pdc->cfg_fields = &pdc_cfg_v3_2; | |
| pdc->regs = &pdc_v3_2; | |
| pdc->enable_intr = pdc_enable_intr_cfg; | |
| } else if (pdc->version >= PDC_VERSION_3_0) { | |
| pdc->cfg_fields = &pdc_cfg_v3_0; | |
| pdc->regs = &pdc_v3_0; | |
| pdc->enable_intr = pdc_enable_intr_bank; | |
| } else { | |
| pdc->cfg_fields = &pdc_cfg_v2_7; | |
| pdc->regs = &pdc_v2_7; | |
| pdc->enable_intr = pdc_enable_intr_bank; | |
| } | |
| pdc->mode = PDC_PASS_THROUGH_MODE; | |
| /* | |
| * PDC has multiple DRV regions, each one provides the same set of | |
| * registers for a particular client in the system. Due to a hardware | |
| * bug on X1E, some writes to the IRQ_ENABLE_BANK register must be | |
| * issued inside the previous region. This region belongs to | |
| * a different client and is not described in the device tree. Map the | |
| * region with the expected offset to preserve support for old DTs. | |
| */ | |
| if (of_device_is_compatible(node, "qcom,x1e80100-pdc")) { | |
| pdc->prev_base = devm_ioremap(dev, res.start - PDC_DRV_SIZE, | |
| pdc->regs->irq_en_reg + IRQ_ENABLE_BANK_MAX); | |
| if (!pdc->prev_base) { | |
| pr_err("%pOF: unable to map previous PDC DRV region\n", node); | |
| return -ENXIO; | |
| } | |
| pdc->x1e_quirk = true; | |
| if (!qcom_scm_is_available()) | |
| return -EPROBE_DEFER; | |
| ret = qcom_scm_io_writel(PDC_GPIO_INT_CTL_ENABLE, PDC_PASS_THROUGH_MODE); | |
| if (ret) { | |
| pdc->mode = PDC_SECONDARY_MODE; | |
| pdc->unmask_gpio = pdc_unmask_gpio_cfg; | |
| pdc->clear_gpio = pdc_clear_gpio_cfg; | |
| } | |
| } | |
| irq_param = pdc_reg_read(pdc->regs->irq_param_reg, 0); | |
| pdc->num_spis = FIELD_GET(GENMASK(7, 0), irq_param); | |
| parent_domain = irq_find_host(parent); | |
| if (!parent_domain) { | |
| pr_err("%pOF: unable to find PDC's parent domain\n", node); | |
| return -ENXIO; | |
| } | |
| raw_spin_lock_init(&pdc->lock); | |
| ret = pdc_setup_pin_mapping(dev); | |
| if (ret) { | |
| pr_err("%pOF: failed to init PDC pin-hwirq mapping\n", node); | |
| return ret; | |
| } | |
| pdc_domain = irq_domain_create_hierarchy(parent_domain, IRQ_DOMAIN_FLAG_QCOM_PDC_WAKEUP, | |
| PDC_MAX_IRQS, of_fwnode_handle(node), | |
| &qcom_pdc_ops, NULL); | |
| if (!pdc_domain) { | |
| pr_err("%pOF: PDC domain add failed\n", node); | |
| return -ENOMEM; | |
| } | |
| irq_domain_update_bus_token(pdc_domain, DOMAIN_BUS_WAKEUP); | |
| return 0; | |
| } | |
| IRQCHIP_PLATFORM_DRIVER_BEGIN(qcom_pdc) | |
| IRQCHIP_MATCH("qcom,pdc", qcom_pdc_probe) | |
| IRQCHIP_PLATFORM_DRIVER_END(qcom_pdc) | |
| MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Power Domain Controller"); | |
| MODULE_LICENSE("GPL v2"); |