| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Driver for keys on GPIO lines capable of generating interrupts. | |
| * | |
| * Copyright 2005 Phil Blundell | |
| * Copyright 2010, 2011 David Jander <david@protonic.nl> | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/hrtimer.h> | |
| #include <linux/init.h> | |
| #include <linux/fs.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/sched.h> | |
| #include <linux/pm.h> | |
| #include <linux/slab.h> | |
| #include <linux/sysctl.h> | |
| #include <linux/proc_fs.h> | |
| #include <linux/delay.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/input.h> | |
| #include <linux/gpio_keys.h> | |
| #include <linux/workqueue.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/gpio/legacy.h> | |
| #include <linux/of.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/spinlock.h> | |
| #include <dt-bindings/input/gpio-keys.h> | |
| struct gpio_button_data { | |
| const struct gpio_keys_button *button; | |
| struct input_dev *input; | |
| struct gpio_desc *gpiod; | |
| unsigned short *code; | |
| struct hrtimer release_timer; | |
| unsigned int release_delay; /* in msecs, for IRQ-only buttons */ | |
| struct delayed_work work; | |
| struct hrtimer debounce_timer; | |
| unsigned int software_debounce; /* in msecs, for GPIO-driven buttons */ | |
| unsigned int irq; | |
| unsigned int wakeirq; | |
| unsigned int wakeup_trigger_type; | |
| spinlock_t lock; | |
| bool disabled; | |
| bool key_pressed; | |
| bool suspended; | |
| bool debounce_use_hrtimer; | |
| }; | |
| struct gpio_keys_drvdata { | |
| const struct gpio_keys_platform_data *pdata; | |
| struct input_dev *input; | |
| struct mutex disable_lock; | |
| unsigned short *keymap; | |
| struct gpio_button_data data[]; | |
| }; | |
| /* | |
| * SYSFS interface for enabling/disabling keys and switches: | |
| * | |
| * There are 4 attributes under /sys/devices/platform/gpio-keys/ | |
| * keys [ro] - bitmap of keys (EV_KEY) which can be | |
| * disabled | |
| * switches [ro] - bitmap of switches (EV_SW) which can be | |
| * disabled | |
| * disabled_keys [rw] - bitmap of keys currently disabled | |
| * disabled_switches [rw] - bitmap of switches currently disabled | |
| * | |
| * Userland can change these values and hence disable event generation | |
| * for each key (or switch). Disabling a key means its interrupt line | |
| * is disabled. | |
| * | |
| * For example, if we have following switches set up as gpio-keys: | |
| * SW_DOCK = 5 | |
| * SW_CAMERA_LENS_COVER = 9 | |
| * SW_KEYPAD_SLIDE = 10 | |
| * SW_FRONT_PROXIMITY = 11 | |
| * This is read from switches: | |
| * 11-9,5 | |
| * Next we want to disable proximity (11) and dock (5), we write: | |
| * 11,5 | |
| * to file disabled_switches. Now proximity and dock IRQs are disabled. | |
| * This can be verified by reading the file disabled_switches: | |
| * 11,5 | |
| * If we now want to enable proximity (11) switch we write: | |
| * 5 | |
| * to disabled_switches. | |
| * | |
| * We can disable only those keys which don't allow sharing the irq. | |
| */ | |
| /** | |
| * get_n_events_by_type() - returns maximum number of events per @type | |
| * @type: type of button (%EV_KEY, %EV_SW) | |
| * | |
| * Return value of this function can be used to allocate bitmap | |
| * large enough to hold all bits for given type. | |
| */ | |
| static int get_n_events_by_type(int type) | |
| { | |
| BUG_ON(type != EV_SW && type != EV_KEY); | |
| return (type == EV_KEY) ? KEY_CNT : SW_CNT; | |
| } | |
| /** | |
| * get_bm_events_by_type() - returns bitmap of supported events per @type | |
| * @dev: input device from which bitmap is retrieved | |
| * @type: type of button (%EV_KEY, %EV_SW) | |
| * | |
| * Return value of this function can be used to allocate bitmap | |
| * large enough to hold all bits for given type. | |
| */ | |
| static const unsigned long *get_bm_events_by_type(struct input_dev *dev, | |
| int type) | |
| { | |
| BUG_ON(type != EV_SW && type != EV_KEY); | |
| return (type == EV_KEY) ? dev->keybit : dev->swbit; | |
| } | |
| static void gpio_keys_quiesce_key(void *data) | |
| { | |
| struct gpio_button_data *bdata = data; | |
| if (!bdata->gpiod) | |
| hrtimer_cancel(&bdata->release_timer); | |
| else if (bdata->debounce_use_hrtimer) | |
| hrtimer_cancel(&bdata->debounce_timer); | |
| else | |
| cancel_delayed_work_sync(&bdata->work); | |
| } | |
| /** | |
| * gpio_keys_disable_button() - disables given GPIO button | |
| * @bdata: button data for button to be disabled | |
| * | |
| * Disables button pointed by @bdata. This is done by masking | |
| * IRQ line. After this function is called, button won't generate | |
| * input events anymore. Note that one can only disable buttons | |
| * that don't share IRQs. | |
| * | |
| * Make sure that @bdata->disable_lock is locked when entering | |
| * this function to avoid races when concurrent threads are | |
| * disabling buttons at the same time. | |
| */ | |
| static void gpio_keys_disable_button(struct gpio_button_data *bdata) | |
| { | |
| if (!bdata->disabled) { | |
| /* | |
| * Disable IRQ and associated timer/work structure. | |
| */ | |
| disable_irq(bdata->irq); | |
| gpio_keys_quiesce_key(bdata); | |
| bdata->disabled = true; | |
| } | |
| } | |
| /** | |
| * gpio_keys_enable_button() - enables given GPIO button | |
| * @bdata: button data for button to be disabled | |
| * | |
| * Enables given button pointed by @bdata. | |
| * | |
| * Make sure that @bdata->disable_lock is locked when entering | |
| * this function to avoid races with concurrent threads trying | |
| * to enable the same button at the same time. | |
| */ | |
| static void gpio_keys_enable_button(struct gpio_button_data *bdata) | |
| { | |
| if (bdata->disabled) { | |
| enable_irq(bdata->irq); | |
| bdata->disabled = false; | |
| } | |
| } | |
| /** | |
| * gpio_keys_attr_show_helper() - fill in stringified bitmap of buttons | |
| * @ddata: pointer to drvdata | |
| * @buf: buffer where stringified bitmap is written | |
| * @type: button type (%EV_KEY, %EV_SW) | |
| * @only_disabled: does caller want only those buttons that are | |
| * currently disabled or all buttons that can be | |
| * disabled | |
| * | |
| * This function writes buttons that can be disabled to @buf. If | |
| * @only_disabled is true, then @buf contains only those buttons | |
| * that are currently disabled. Returns 0 on success or negative | |
| * errno on failure. | |
| */ | |
| static ssize_t gpio_keys_attr_show_helper(struct gpio_keys_drvdata *ddata, | |
| char *buf, unsigned int type, | |
| bool only_disabled) | |
| { | |
| int n_events = get_n_events_by_type(type); | |
| unsigned long *bits; | |
| ssize_t ret; | |
| int i; | |
| bits = bitmap_zalloc(n_events, GFP_KERNEL); | |
| if (!bits) | |
| return -ENOMEM; | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| struct gpio_button_data *bdata = &ddata->data[i]; | |
| if (bdata->button->type != type) | |
| continue; | |
| if (only_disabled && !bdata->disabled) | |
| continue; | |
| __set_bit(*bdata->code, bits); | |
| } | |
| ret = scnprintf(buf, PAGE_SIZE - 1, "%*pbl", n_events, bits); | |
| buf[ret++] = '\n'; | |
| buf[ret] = '\0'; | |
| bitmap_free(bits); | |
| return ret; | |
| } | |
| /** | |
| * gpio_keys_attr_store_helper() - enable/disable buttons based on given bitmap | |
| * @ddata: pointer to drvdata | |
| * @buf: buffer from userspace that contains stringified bitmap | |
| * @type: button type (%EV_KEY, %EV_SW) | |
| * | |
| * This function parses stringified bitmap from @buf and disables/enables | |
| * GPIO buttons accordingly. Returns 0 on success and negative error | |
| * on failure. | |
| */ | |
| static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata, | |
| const char *buf, unsigned int type) | |
| { | |
| int n_events = get_n_events_by_type(type); | |
| const unsigned long *bitmap = get_bm_events_by_type(ddata->input, type); | |
| ssize_t error; | |
| int i; | |
| unsigned long *bits __free(bitmap) = bitmap_alloc(n_events, GFP_KERNEL); | |
| if (!bits) | |
| return -ENOMEM; | |
| error = bitmap_parselist(buf, bits, n_events); | |
| if (error) | |
| return error; | |
| /* First validate */ | |
| if (!bitmap_subset(bits, bitmap, n_events)) | |
| return -EINVAL; | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| struct gpio_button_data *bdata = &ddata->data[i]; | |
| if (bdata->button->type != type) | |
| continue; | |
| if (test_bit(*bdata->code, bits) && | |
| !bdata->button->can_disable) { | |
| return -EINVAL; | |
| } | |
| } | |
| guard(mutex)(&ddata->disable_lock); | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| struct gpio_button_data *bdata = &ddata->data[i]; | |
| if (bdata->button->type != type) | |
| continue; | |
| if (test_bit(*bdata->code, bits)) | |
| gpio_keys_disable_button(bdata); | |
| else | |
| gpio_keys_enable_button(bdata); | |
| } | |
| return 0; | |
| } | |
| #define ATTR_SHOW_FN(name, type, only_disabled) \ | |
| static ssize_t gpio_keys_show_##name(struct device *dev, \ | |
| struct device_attribute *attr, \ | |
| char *buf) \ | |
| { \ | |
| struct platform_device *pdev = to_platform_device(dev); \ | |
| struct gpio_keys_drvdata *ddata = platform_get_drvdata(pdev); \ | |
| \ | |
| return gpio_keys_attr_show_helper(ddata, buf, \ | |
| type, only_disabled); \ | |
| } | |
| ATTR_SHOW_FN(keys, EV_KEY, false); | |
| ATTR_SHOW_FN(switches, EV_SW, false); | |
| ATTR_SHOW_FN(disabled_keys, EV_KEY, true); | |
| ATTR_SHOW_FN(disabled_switches, EV_SW, true); | |
| /* | |
| * ATTRIBUTES: | |
| * | |
| * /sys/devices/platform/gpio-keys/keys [ro] | |
| * /sys/devices/platform/gpio-keys/switches [ro] | |
| */ | |
| static DEVICE_ATTR(keys, S_IRUGO, gpio_keys_show_keys, NULL); | |
| static DEVICE_ATTR(switches, S_IRUGO, gpio_keys_show_switches, NULL); | |
| #define ATTR_STORE_FN(name, type) \ | |
| static ssize_t gpio_keys_store_##name(struct device *dev, \ | |
| struct device_attribute *attr, \ | |
| const char *buf, \ | |
| size_t count) \ | |
| { \ | |
| struct platform_device *pdev = to_platform_device(dev); \ | |
| struct gpio_keys_drvdata *ddata = platform_get_drvdata(pdev); \ | |
| ssize_t error; \ | |
| \ | |
| error = gpio_keys_attr_store_helper(ddata, buf, type); \ | |
| if (error) \ | |
| return error; \ | |
| \ | |
| return count; \ | |
| } | |
| ATTR_STORE_FN(disabled_keys, EV_KEY); | |
| ATTR_STORE_FN(disabled_switches, EV_SW); | |
| /* | |
| * ATTRIBUTES: | |
| * | |
| * /sys/devices/platform/gpio-keys/disabled_keys [rw] | |
| * /sys/devices/platform/gpio-keys/disables_switches [rw] | |
| */ | |
| static DEVICE_ATTR(disabled_keys, S_IWUSR | S_IRUGO, | |
| gpio_keys_show_disabled_keys, | |
| gpio_keys_store_disabled_keys); | |
| static DEVICE_ATTR(disabled_switches, S_IWUSR | S_IRUGO, | |
| gpio_keys_show_disabled_switches, | |
| gpio_keys_store_disabled_switches); | |
| static struct attribute *gpio_keys_attrs[] = { | |
| &dev_attr_keys.attr, | |
| &dev_attr_switches.attr, | |
| &dev_attr_disabled_keys.attr, | |
| &dev_attr_disabled_switches.attr, | |
| NULL, | |
| }; | |
| ATTRIBUTE_GROUPS(gpio_keys); | |
| static void gpio_keys_gpio_report_event(struct gpio_button_data *bdata) | |
| { | |
| const struct gpio_keys_button *button = bdata->button; | |
| struct input_dev *input = bdata->input; | |
| unsigned int type = button->type ?: EV_KEY; | |
| int state; | |
| state = bdata->debounce_use_hrtimer ? | |
| gpiod_get_value(bdata->gpiod) : | |
| gpiod_get_value_cansleep(bdata->gpiod); | |
| if (state < 0) { | |
| dev_err(input->dev.parent, | |
| "failed to get gpio state: %d\n", state); | |
| return; | |
| } | |
| if (type == EV_ABS) { | |
| if (state) | |
| input_event(input, type, button->code, button->value); | |
| } else { | |
| input_event(input, type, *bdata->code, state); | |
| } | |
| } | |
| static void gpio_keys_debounce_event(struct gpio_button_data *bdata) | |
| { | |
| gpio_keys_gpio_report_event(bdata); | |
| input_sync(bdata->input); | |
| if (bdata->button->wakeup) | |
| pm_relax(bdata->input->dev.parent); | |
| } | |
| static void gpio_keys_gpio_work_func(struct work_struct *work) | |
| { | |
| struct gpio_button_data *bdata = | |
| container_of(work, struct gpio_button_data, work.work); | |
| gpio_keys_debounce_event(bdata); | |
| } | |
| static enum hrtimer_restart gpio_keys_debounce_timer(struct hrtimer *t) | |
| { | |
| struct gpio_button_data *bdata = | |
| container_of(t, struct gpio_button_data, debounce_timer); | |
| gpio_keys_debounce_event(bdata); | |
| return HRTIMER_NORESTART; | |
| } | |
| static irqreturn_t gpio_keys_gpio_isr(int irq, void *dev_id) | |
| { | |
| struct gpio_button_data *bdata = dev_id; | |
| BUG_ON(irq != bdata->irq); | |
| if (bdata->button->wakeup) { | |
| const struct gpio_keys_button *button = bdata->button; | |
| pm_stay_awake(bdata->input->dev.parent); | |
| if (bdata->suspended && | |
| (button->type == 0 || button->type == EV_KEY)) { | |
| /* | |
| * Simulate wakeup key press in case the key has | |
| * already released by the time we got interrupt | |
| * handler to run. | |
| */ | |
| input_report_key(bdata->input, button->code, 1); | |
| } | |
| } | |
| if (bdata->debounce_use_hrtimer) { | |
| hrtimer_start(&bdata->debounce_timer, | |
| ms_to_ktime(bdata->software_debounce), | |
| HRTIMER_MODE_REL); | |
| } else { | |
| mod_delayed_work(system_dfl_wq, | |
| &bdata->work, | |
| msecs_to_jiffies(bdata->software_debounce)); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static enum hrtimer_restart gpio_keys_irq_timer(struct hrtimer *t) | |
| { | |
| struct gpio_button_data *bdata = container_of(t, | |
| struct gpio_button_data, | |
| release_timer); | |
| struct input_dev *input = bdata->input; | |
| guard(spinlock_irqsave)(&bdata->lock); | |
| if (bdata->key_pressed) { | |
| input_report_key(input, *bdata->code, 0); | |
| input_sync(input); | |
| bdata->key_pressed = false; | |
| } | |
| return HRTIMER_NORESTART; | |
| } | |
| static irqreturn_t gpio_keys_irq_isr(int irq, void *dev_id) | |
| { | |
| struct gpio_button_data *bdata = dev_id; | |
| struct input_dev *input = bdata->input; | |
| BUG_ON(irq != bdata->irq); | |
| guard(spinlock_irqsave)(&bdata->lock); | |
| if (!bdata->key_pressed) { | |
| if (bdata->button->wakeup) | |
| pm_wakeup_event(bdata->input->dev.parent, 0); | |
| input_report_key(input, *bdata->code, 1); | |
| input_sync(input); | |
| if (!bdata->release_delay) { | |
| input_report_key(input, *bdata->code, 0); | |
| input_sync(input); | |
| goto out; | |
| } | |
| bdata->key_pressed = true; | |
| } | |
| if (bdata->release_delay) | |
| hrtimer_start(&bdata->release_timer, | |
| ms_to_ktime(bdata->release_delay), | |
| HRTIMER_MODE_REL); | |
| out: | |
| return IRQ_HANDLED; | |
| } | |
| static int gpio_keys_setup_key(struct platform_device *pdev, | |
| struct input_dev *input, | |
| struct gpio_keys_drvdata *ddata, | |
| const struct gpio_keys_button *button, | |
| int idx, | |
| struct fwnode_handle *child) | |
| { | |
| const char *desc = button->desc ? button->desc : "gpio_keys"; | |
| struct device *dev = &pdev->dev; | |
| struct gpio_button_data *bdata = &ddata->data[idx]; | |
| irq_handler_t isr; | |
| unsigned long irqflags; | |
| const char *wakedesc; | |
| int irq; | |
| int error; | |
| bdata->input = input; | |
| bdata->button = button; | |
| spin_lock_init(&bdata->lock); | |
| if (child) { | |
| bdata->gpiod = devm_fwnode_gpiod_get(dev, child, | |
| NULL, GPIOD_IN, desc); | |
| if (IS_ERR(bdata->gpiod)) { | |
| error = PTR_ERR(bdata->gpiod); | |
| if (error != -ENOENT) | |
| return dev_err_probe(dev, error, | |
| "failed to get gpio\n"); | |
| /* | |
| * GPIO is optional, we may be dealing with | |
| * purely interrupt-driven setup. | |
| */ | |
| bdata->gpiod = NULL; | |
| } | |
| #ifdef CONFIG_GPIOLIB_LEGACY | |
| } else if (gpio_is_valid(button->gpio)) { | |
| /* | |
| * Legacy GPIO number, so request the GPIO here and | |
| * convert it to descriptor. | |
| */ | |
| error = devm_gpio_request_one(dev, button->gpio, GPIOF_IN, desc); | |
| if (error < 0) { | |
| dev_err(dev, "Failed to request GPIO %d, error %d\n", | |
| button->gpio, error); | |
| return error; | |
| } | |
| bdata->gpiod = gpio_to_desc(button->gpio); | |
| if (!bdata->gpiod) | |
| return -EINVAL; | |
| if (button->active_low ^ gpiod_is_active_low(bdata->gpiod)) | |
| gpiod_toggle_active_low(bdata->gpiod); | |
| #endif | |
| } | |
| if (bdata->gpiod) { | |
| bool active_low = gpiod_is_active_low(bdata->gpiod); | |
| if (button->debounce_interval) { | |
| error = gpiod_set_debounce(bdata->gpiod, | |
| button->debounce_interval * 1000); | |
| /* use timer if gpiolib doesn't provide debounce */ | |
| if (error < 0) | |
| bdata->software_debounce = | |
| button->debounce_interval; | |
| /* | |
| * If reading the GPIO won't sleep, we can use a | |
| * hrtimer instead of a standard timer for the software | |
| * debounce, to reduce the latency as much as possible. | |
| */ | |
| bdata->debounce_use_hrtimer = | |
| !gpiod_cansleep(bdata->gpiod); | |
| } | |
| /* | |
| * If an interrupt was specified, use it instead of the gpio | |
| * interrupt and use the gpio for reading the state. A separate | |
| * interrupt may be used as the main button interrupt for | |
| * runtime PM to detect events also in deeper idle states. If a | |
| * dedicated wakeirq is used for system suspend only, see below | |
| * for bdata->wakeirq setup. | |
| */ | |
| if (button->irq) { | |
| bdata->irq = button->irq; | |
| } else { | |
| irq = gpiod_to_irq(bdata->gpiod); | |
| if (irq < 0) { | |
| error = irq; | |
| dev_err_probe(dev, error, | |
| "Unable to get irq number for GPIO\n"); | |
| return error; | |
| } | |
| bdata->irq = irq; | |
| } | |
| INIT_DELAYED_WORK(&bdata->work, gpio_keys_gpio_work_func); | |
| hrtimer_setup(&bdata->debounce_timer, gpio_keys_debounce_timer, | |
| CLOCK_REALTIME, HRTIMER_MODE_REL); | |
| isr = gpio_keys_gpio_isr; | |
| irqflags = IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING; | |
| switch (button->wakeup_event_action) { | |
| case EV_ACT_ASSERTED: | |
| bdata->wakeup_trigger_type = active_low ? | |
| IRQ_TYPE_EDGE_FALLING : IRQ_TYPE_EDGE_RISING; | |
| break; | |
| case EV_ACT_DEASSERTED: | |
| bdata->wakeup_trigger_type = active_low ? | |
| IRQ_TYPE_EDGE_RISING : IRQ_TYPE_EDGE_FALLING; | |
| break; | |
| case EV_ACT_ANY: | |
| default: | |
| /* | |
| * For other cases, we are OK letting suspend/resume | |
| * not reconfigure the trigger type. | |
| */ | |
| break; | |
| } | |
| } else { | |
| if (button->irq) { | |
| bdata->irq = button->irq; | |
| } else { | |
| irq = platform_get_irq_optional(pdev, idx); | |
| if (irq < 0) { | |
| error = irq; | |
| return dev_err_probe(dev, error, | |
| "Unable to determine IRQ# for button #%d", | |
| idx); | |
| } | |
| bdata->irq = irq; | |
| } | |
| if (button->type && button->type != EV_KEY) { | |
| dev_err(dev, "Only EV_KEY allowed for IRQ buttons.\n"); | |
| return -EINVAL; | |
| } | |
| bdata->release_delay = button->debounce_interval; | |
| hrtimer_setup(&bdata->release_timer, gpio_keys_irq_timer, | |
| CLOCK_REALTIME, HRTIMER_MODE_REL); | |
| isr = gpio_keys_irq_isr; | |
| irqflags = 0; | |
| /* | |
| * For IRQ buttons, there is no interrupt for release. | |
| * So we don't need to reconfigure the trigger type for wakeup. | |
| */ | |
| } | |
| bdata->code = &ddata->keymap[idx]; | |
| *bdata->code = button->code; | |
| input_set_capability(input, button->type ?: EV_KEY, *bdata->code); | |
| /* | |
| * Install custom action to cancel release timer and | |
| * workqueue item. | |
| */ | |
| error = devm_add_action(dev, gpio_keys_quiesce_key, bdata); | |
| if (error) { | |
| dev_err(dev, "failed to register quiesce action, error: %d\n", | |
| error); | |
| return error; | |
| } | |
| /* | |
| * If platform has specified that the button can be disabled, | |
| * we don't want it to share the interrupt line. | |
| */ | |
| if (!button->can_disable) | |
| irqflags |= IRQF_SHARED; | |
| error = devm_request_any_context_irq(dev, bdata->irq, isr, irqflags, | |
| desc, bdata); | |
| if (error < 0) { | |
| dev_err(dev, "Unable to claim irq %d; error %d\n", | |
| bdata->irq, error); | |
| return error; | |
| } | |
| if (!button->wakeirq) | |
| return 0; | |
| /* Use :wakeup suffix like drivers/base/power/wakeirq.c does */ | |
| wakedesc = devm_kasprintf(dev, GFP_KERNEL, "%s:wakeup", desc); | |
| if (!wakedesc) | |
| return -ENOMEM; | |
| bdata->wakeirq = button->wakeirq; | |
| irqflags |= IRQF_NO_SUSPEND; | |
| /* | |
| * Wakeirq shares the handler with the main interrupt, it's only | |
| * active during system suspend. See gpio_keys_button_enable_wakeup() | |
| * and gpio_keys_button_disable_wakeup(). | |
| */ | |
| error = devm_request_any_context_irq(dev, bdata->wakeirq, isr, | |
| irqflags, wakedesc, bdata); | |
| if (error < 0) { | |
| dev_err(dev, "Unable to claim wakeirq %d; error %d\n", | |
| bdata->irq, error); | |
| return error; | |
| } | |
| /* | |
| * Disable wakeirq until suspend. IRQF_NO_AUTOEN won't work if | |
| * IRQF_SHARED was set based on !button->can_disable. | |
| */ | |
| disable_irq(bdata->wakeirq); | |
| return 0; | |
| } | |
| static void gpio_keys_report_state(struct gpio_keys_drvdata *ddata) | |
| { | |
| struct input_dev *input = ddata->input; | |
| int i; | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| struct gpio_button_data *bdata = &ddata->data[i]; | |
| if (bdata->gpiod) | |
| gpio_keys_gpio_report_event(bdata); | |
| } | |
| input_sync(input); | |
| } | |
| static int gpio_keys_open(struct input_dev *input) | |
| { | |
| struct gpio_keys_drvdata *ddata = input_get_drvdata(input); | |
| const struct gpio_keys_platform_data *pdata = ddata->pdata; | |
| int error; | |
| if (pdata->enable) { | |
| error = pdata->enable(input->dev.parent); | |
| if (error) | |
| return error; | |
| } | |
| /* Report current state of buttons that are connected to GPIOs */ | |
| gpio_keys_report_state(ddata); | |
| return 0; | |
| } | |
| static void gpio_keys_close(struct input_dev *input) | |
| { | |
| struct gpio_keys_drvdata *ddata = input_get_drvdata(input); | |
| const struct gpio_keys_platform_data *pdata = ddata->pdata; | |
| if (pdata->disable) | |
| pdata->disable(input->dev.parent); | |
| } | |
| /* | |
| * Handlers for alternative sources of platform_data | |
| */ | |
| /* | |
| * Translate properties into platform_data | |
| */ | |
| static struct gpio_keys_platform_data * | |
| gpio_keys_get_devtree_pdata(struct device *dev) | |
| { | |
| struct gpio_keys_platform_data *pdata; | |
| struct gpio_keys_button *button; | |
| int nbuttons, irq; | |
| nbuttons = device_get_child_node_count(dev); | |
| if (nbuttons == 0) | |
| return ERR_PTR(-ENODEV); | |
| pdata = devm_kzalloc(dev, | |
| sizeof(*pdata) + nbuttons * sizeof(*button), | |
| GFP_KERNEL); | |
| if (!pdata) | |
| return ERR_PTR(-ENOMEM); | |
| button = (struct gpio_keys_button *)(pdata + 1); | |
| pdata->buttons = button; | |
| pdata->nbuttons = nbuttons; | |
| pdata->rep = device_property_read_bool(dev, "autorepeat"); | |
| device_property_read_string(dev, "label", &pdata->name); | |
| device_for_each_child_node_scoped(dev, child) { | |
| if (is_of_node(child)) { | |
| irq = of_irq_get_byname(to_of_node(child), "irq"); | |
| if (irq > 0) | |
| button->irq = irq; | |
| irq = of_irq_get_byname(to_of_node(child), "wakeup"); | |
| if (irq > 0) | |
| button->wakeirq = irq; | |
| if (!button->irq && !button->wakeirq) | |
| button->irq = | |
| irq_of_parse_and_map(to_of_node(child), 0); | |
| } | |
| if (fwnode_property_read_u32(child, "linux,code", | |
| &button->code)) { | |
| dev_err(dev, "Button without keycode\n"); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| fwnode_property_read_string(child, "label", &button->desc); | |
| if (fwnode_property_read_u32(child, "linux,input-type", | |
| &button->type)) | |
| button->type = EV_KEY; | |
| fwnode_property_read_u32(child, "linux,input-value", | |
| (u32 *)&button->value); | |
| button->wakeup = | |
| fwnode_property_read_bool(child, "wakeup-source") || | |
| /* legacy name */ | |
| fwnode_property_read_bool(child, "gpio-key,wakeup"); | |
| fwnode_property_read_u32(child, "wakeup-event-action", | |
| &button->wakeup_event_action); | |
| button->can_disable = | |
| fwnode_property_read_bool(child, "linux,can-disable"); | |
| if (fwnode_property_read_u32(child, "debounce-interval", | |
| &button->debounce_interval)) | |
| button->debounce_interval = 5; | |
| button++; | |
| } | |
| return pdata; | |
| } | |
| static const struct of_device_id gpio_keys_of_match[] = { | |
| { .compatible = "gpio-keys", }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, gpio_keys_of_match); | |
| static int gpio_keys_probe(struct platform_device *pdev) | |
| { | |
| struct device *dev = &pdev->dev; | |
| const struct gpio_keys_platform_data *pdata = dev_get_platdata(dev); | |
| struct fwnode_handle *child = NULL; | |
| struct gpio_keys_drvdata *ddata; | |
| struct input_dev *input; | |
| int i, error; | |
| int wakeup = 0; | |
| if (!pdata) { | |
| pdata = gpio_keys_get_devtree_pdata(dev); | |
| if (IS_ERR(pdata)) | |
| return PTR_ERR(pdata); | |
| } | |
| ddata = devm_kzalloc(dev, struct_size(ddata, data, pdata->nbuttons), | |
| GFP_KERNEL); | |
| if (!ddata) { | |
| dev_err(dev, "failed to allocate state\n"); | |
| return -ENOMEM; | |
| } | |
| ddata->keymap = devm_kcalloc(dev, | |
| pdata->nbuttons, sizeof(ddata->keymap[0]), | |
| GFP_KERNEL); | |
| if (!ddata->keymap) | |
| return -ENOMEM; | |
| input = devm_input_allocate_device(dev); | |
| if (!input) { | |
| dev_err(dev, "failed to allocate input device\n"); | |
| return -ENOMEM; | |
| } | |
| ddata->pdata = pdata; | |
| ddata->input = input; | |
| mutex_init(&ddata->disable_lock); | |
| platform_set_drvdata(pdev, ddata); | |
| input_set_drvdata(input, ddata); | |
| input->name = pdata->name ? : pdev->name; | |
| input->phys = "gpio-keys/input0"; | |
| input->dev.parent = dev; | |
| input->open = gpio_keys_open; | |
| input->close = gpio_keys_close; | |
| input->id.bustype = BUS_HOST; | |
| input->id.vendor = 0x0001; | |
| input->id.product = 0x0001; | |
| input->id.version = 0x0100; | |
| input->keycode = ddata->keymap; | |
| input->keycodesize = sizeof(ddata->keymap[0]); | |
| input->keycodemax = pdata->nbuttons; | |
| /* Enable auto repeat feature of Linux input subsystem */ | |
| if (pdata->rep) | |
| __set_bit(EV_REP, input->evbit); | |
| for (i = 0; i < pdata->nbuttons; i++) { | |
| const struct gpio_keys_button *button = &pdata->buttons[i]; | |
| if (!dev_get_platdata(dev)) { | |
| child = device_get_next_child_node(dev, child); | |
| if (!child) { | |
| dev_err(dev, | |
| "missing child device node for entry %d\n", | |
| i); | |
| return -EINVAL; | |
| } | |
| } | |
| error = gpio_keys_setup_key(pdev, input, ddata, | |
| button, i, child); | |
| if (error) { | |
| fwnode_handle_put(child); | |
| return error; | |
| } | |
| if (button->wakeup) | |
| wakeup = 1; | |
| } | |
| fwnode_handle_put(child); | |
| error = input_register_device(input); | |
| if (error) { | |
| dev_err(dev, "Unable to register input device, error: %d\n", | |
| error); | |
| return error; | |
| } | |
| device_init_wakeup(dev, wakeup); | |
| return 0; | |
| } | |
| static int __maybe_unused | |
| gpio_keys_button_enable_wakeup(struct gpio_button_data *bdata) | |
| { | |
| int error; | |
| error = enable_irq_wake(bdata->irq); | |
| if (error) { | |
| dev_err(bdata->input->dev.parent, | |
| "failed to configure IRQ %d as wakeup source: %d\n", | |
| bdata->irq, error); | |
| return error; | |
| } | |
| if (bdata->wakeup_trigger_type) { | |
| error = irq_set_irq_type(bdata->irq, | |
| bdata->wakeup_trigger_type); | |
| if (error) { | |
| dev_err(bdata->input->dev.parent, | |
| "failed to set wakeup trigger %08x for IRQ %d: %d\n", | |
| bdata->wakeup_trigger_type, bdata->irq, error); | |
| disable_irq_wake(bdata->irq); | |
| return error; | |
| } | |
| } | |
| if (bdata->wakeirq) { | |
| enable_irq(bdata->wakeirq); | |
| disable_irq(bdata->irq); | |
| } | |
| return 0; | |
| } | |
| static void __maybe_unused | |
| gpio_keys_button_disable_wakeup(struct gpio_button_data *bdata) | |
| { | |
| int error; | |
| if (bdata->wakeirq) { | |
| enable_irq(bdata->irq); | |
| disable_irq(bdata->wakeirq); | |
| } | |
| /* | |
| * The trigger type is always both edges for gpio-based keys and we do | |
| * not support changing wakeup trigger for interrupt-based keys. | |
| */ | |
| if (bdata->wakeup_trigger_type) { | |
| error = irq_set_irq_type(bdata->irq, IRQ_TYPE_EDGE_BOTH); | |
| if (error) | |
| dev_warn(bdata->input->dev.parent, | |
| "failed to restore interrupt trigger for IRQ %d: %d\n", | |
| bdata->irq, error); | |
| } | |
| error = disable_irq_wake(bdata->irq); | |
| if (error) | |
| dev_warn(bdata->input->dev.parent, | |
| "failed to disable IRQ %d as wake source: %d\n", | |
| bdata->irq, error); | |
| } | |
| static int __maybe_unused | |
| gpio_keys_enable_wakeup(struct gpio_keys_drvdata *ddata) | |
| { | |
| struct gpio_button_data *bdata; | |
| int error; | |
| int i; | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| bdata = &ddata->data[i]; | |
| if (bdata->button->wakeup) { | |
| error = gpio_keys_button_enable_wakeup(bdata); | |
| if (error) | |
| goto err_out; | |
| } | |
| bdata->suspended = true; | |
| } | |
| return 0; | |
| err_out: | |
| while (i--) { | |
| bdata = &ddata->data[i]; | |
| if (bdata->button->wakeup) | |
| gpio_keys_button_disable_wakeup(bdata); | |
| bdata->suspended = false; | |
| } | |
| return error; | |
| } | |
| static void __maybe_unused | |
| gpio_keys_disable_wakeup(struct gpio_keys_drvdata *ddata) | |
| { | |
| struct gpio_button_data *bdata; | |
| int i; | |
| for (i = 0; i < ddata->pdata->nbuttons; i++) { | |
| bdata = &ddata->data[i]; | |
| bdata->suspended = false; | |
| if (irqd_is_wakeup_set(irq_get_irq_data(bdata->irq))) | |
| gpio_keys_button_disable_wakeup(bdata); | |
| } | |
| } | |
| static int gpio_keys_suspend(struct device *dev) | |
| { | |
| struct gpio_keys_drvdata *ddata = dev_get_drvdata(dev); | |
| struct input_dev *input = ddata->input; | |
| int error; | |
| if (device_may_wakeup(dev)) { | |
| error = gpio_keys_enable_wakeup(ddata); | |
| if (error) | |
| return error; | |
| } else { | |
| guard(mutex)(&input->mutex); | |
| if (input_device_enabled(input)) | |
| gpio_keys_close(input); | |
| } | |
| return 0; | |
| } | |
| static int gpio_keys_resume(struct device *dev) | |
| { | |
| struct gpio_keys_drvdata *ddata = dev_get_drvdata(dev); | |
| struct input_dev *input = ddata->input; | |
| int error; | |
| if (device_may_wakeup(dev)) { | |
| gpio_keys_disable_wakeup(ddata); | |
| } else { | |
| guard(mutex)(&input->mutex); | |
| if (input_device_enabled(input)) { | |
| error = gpio_keys_open(input); | |
| if (error) | |
| return error; | |
| } | |
| } | |
| gpio_keys_report_state(ddata); | |
| return 0; | |
| } | |
| static DEFINE_SIMPLE_DEV_PM_OPS(gpio_keys_pm_ops, gpio_keys_suspend, gpio_keys_resume); | |
| static void gpio_keys_shutdown(struct platform_device *pdev) | |
| { | |
| int ret; | |
| ret = gpio_keys_suspend(&pdev->dev); | |
| if (ret) | |
| dev_err(&pdev->dev, "failed to shutdown\n"); | |
| } | |
| static struct platform_driver gpio_keys_device_driver = { | |
| .probe = gpio_keys_probe, | |
| .shutdown = gpio_keys_shutdown, | |
| .driver = { | |
| .name = "gpio-keys", | |
| .pm = pm_sleep_ptr(&gpio_keys_pm_ops), | |
| .of_match_table = gpio_keys_of_match, | |
| .dev_groups = gpio_keys_groups, | |
| } | |
| }; | |
| static int __init gpio_keys_init(void) | |
| { | |
| return platform_driver_register(&gpio_keys_device_driver); | |
| } | |
| static void __exit gpio_keys_exit(void) | |
| { | |
| platform_driver_unregister(&gpio_keys_device_driver); | |
| } | |
| late_initcall(gpio_keys_init); | |
| module_exit(gpio_keys_exit); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("Phil Blundell <pb@handhelds.org>"); | |
| MODULE_DESCRIPTION("Keyboard driver for GPIOs"); | |
| MODULE_ALIAS("platform:gpio-keys"); |