| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * mlx90614.c - Support for Melexis MLX90614/MLX90615 contactless IR temperature sensor | |
| * | |
| * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net> | |
| * Copyright (c) 2015 Essensium NV | |
| * Copyright (c) 2015 Melexis | |
| * | |
| * Driver for the Melexis MLX90614/MLX90615 I2C 16-bit IR thermopile sensor | |
| * | |
| * MLX90614 - 17-bit ADC + MLX90302 DSP | |
| * MLX90615 - 16-bit ADC + MLX90325 DSP | |
| * | |
| * (7-bit I2C slave address 0x5a, 100KHz bus speed only!) | |
| * | |
| * To wake up from sleep mode, the SDA line must be held low while SCL is high | |
| * for at least 33ms. This is achieved with an extra GPIO that can be connected | |
| * directly to the SDA line. In normal operation, the GPIO is set as input and | |
| * will not interfere in I2C communication. While the GPIO is driven low, the | |
| * i2c adapter is locked since it cannot be used by other clients. The SCL line | |
| * always has a pull-up so we do not need an extra GPIO to drive it high. If | |
| * the "wakeup" GPIO is not given, power management will be disabled. | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/i2c.h> | |
| #include <linux/jiffies.h> | |
| #include <linux/module.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/iio/iio.h> | |
| #include <linux/iio/sysfs.h> | |
| #define MLX90614_OP_RAM 0x00 | |
| #define MLX90614_OP_EEPROM 0x20 | |
| #define MLX90614_OP_SLEEP 0xff | |
| #define MLX90615_OP_EEPROM 0x10 | |
| #define MLX90615_OP_RAM 0x20 | |
| #define MLX90615_OP_SLEEP 0xc6 | |
| /* Control bits in configuration register */ | |
| #define MLX90614_CONFIG_IIR_SHIFT 0 /* IIR coefficient */ | |
| #define MLX90614_CONFIG_IIR_MASK (0x7 << MLX90614_CONFIG_IIR_SHIFT) | |
| #define MLX90614_CONFIG_DUAL_SHIFT 6 /* single (0) or dual (1) IR sensor */ | |
| #define MLX90614_CONFIG_DUAL_MASK (1 << MLX90614_CONFIG_DUAL_SHIFT) | |
| #define MLX90614_CONFIG_FIR_SHIFT 8 /* FIR coefficient */ | |
| #define MLX90614_CONFIG_FIR_MASK (0x7 << MLX90614_CONFIG_FIR_SHIFT) | |
| #define MLX90615_CONFIG_IIR_SHIFT 12 /* IIR coefficient */ | |
| #define MLX90615_CONFIG_IIR_MASK (0x7 << MLX90615_CONFIG_IIR_SHIFT) | |
| /* Timings (in ms) */ | |
| #define MLX90614_TIMING_EEPROM 20 /* time for EEPROM write/erase to complete */ | |
| #define MLX90614_TIMING_WAKEUP 34 /* time to hold SDA low for wake-up */ | |
| #define MLX90614_TIMING_STARTUP 250 /* time before first data after wake-up */ | |
| #define MLX90615_TIMING_WAKEUP 22 /* time to hold SCL low for wake-up */ | |
| #define MLX90614_AUTOSLEEP_DELAY 5000 /* default autosleep delay */ | |
| /* Magic constants */ | |
| #define MLX90614_CONST_OFFSET_DEC -13657 /* decimal part of the Kelvin offset */ | |
| #define MLX90614_CONST_OFFSET_REM 500000 /* remainder of offset (273.15*50) */ | |
| #define MLX90614_CONST_SCALE 20 /* Scale in milliKelvin (0.02 * 1000) */ | |
| #define MLX90614_CONST_FIR 0x7 /* Fixed value for FIR part of low pass filter */ | |
| struct mlx_chip_info { | |
| /* EEPROM offsets with 16-bit data, MSB first */ | |
| /* emissivity correction coefficient */ | |
| u8 op_eeprom_emissivity; | |
| u8 op_eeprom_config1; | |
| /* RAM offsets with 16-bit data, MSB first */ | |
| /* ambient temperature */ | |
| u8 op_ram_ta; | |
| /* object 1 temperature */ | |
| u8 op_ram_tobj1; | |
| /* object 2 temperature */ | |
| u8 op_ram_tobj2; | |
| u8 op_sleep; | |
| /* support for two input channels (MLX90614 only) */ | |
| u8 dual_channel; | |
| u8 wakeup_delay_ms; | |
| u16 emissivity_max; | |
| u16 fir_config_mask; | |
| u16 iir_config_mask; | |
| int iir_valid_offset; | |
| u16 iir_values[8]; | |
| int iir_freqs[8][2]; | |
| }; | |
| struct mlx90614_data { | |
| struct i2c_client *client; | |
| struct mutex lock; /* for EEPROM access only */ | |
| struct gpio_desc *wakeup_gpio; /* NULL to disable sleep/wake-up */ | |
| const struct mlx_chip_info *chip_info; /* Chip hardware details */ | |
| unsigned long ready_timestamp; /* in jiffies */ | |
| }; | |
| /* | |
| * Erase an address and write word. | |
| * The mutex must be locked before calling. | |
| */ | |
| static s32 mlx90614_write_word(const struct i2c_client *client, u8 command, | |
| u16 value) | |
| { | |
| /* | |
| * Note: The mlx90614 requires a PEC on writing but does not send us a | |
| * valid PEC on reading. Hence, we cannot set I2C_CLIENT_PEC in | |
| * i2c_client.flags. As a workaround, we use i2c_smbus_xfer here. | |
| */ | |
| union i2c_smbus_data data; | |
| s32 ret; | |
| dev_dbg(&client->dev, "Writing 0x%x to address 0x%x", value, command); | |
| data.word = 0x0000; /* erase command */ | |
| ret = i2c_smbus_xfer(client->adapter, client->addr, | |
| client->flags | I2C_CLIENT_PEC, | |
| I2C_SMBUS_WRITE, command, | |
| I2C_SMBUS_WORD_DATA, &data); | |
| if (ret < 0) | |
| return ret; | |
| msleep(MLX90614_TIMING_EEPROM); | |
| data.word = value; /* actual write */ | |
| ret = i2c_smbus_xfer(client->adapter, client->addr, | |
| client->flags | I2C_CLIENT_PEC, | |
| I2C_SMBUS_WRITE, command, | |
| I2C_SMBUS_WORD_DATA, &data); | |
| msleep(MLX90614_TIMING_EEPROM); | |
| return ret; | |
| } | |
| /* | |
| * Find the IIR value inside iir_values array and return its position | |
| * which is equivalent to the bit value in sensor register | |
| */ | |
| static inline s32 mlx90614_iir_search(const struct i2c_client *client, | |
| int value) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| int i; | |
| s32 ret; | |
| for (i = chip_info->iir_valid_offset; | |
| i < ARRAY_SIZE(chip_info->iir_values); | |
| i++) { | |
| if (value == chip_info->iir_values[i]) | |
| break; | |
| } | |
| if (i == ARRAY_SIZE(chip_info->iir_values)) | |
| return -EINVAL; | |
| /* | |
| * CONFIG register values must not be changed so | |
| * we must read them before we actually write | |
| * changes | |
| */ | |
| ret = i2c_smbus_read_word_data(client, chip_info->op_eeprom_config1); | |
| if (ret < 0) | |
| return ret; | |
| /* Modify FIR on parts which have configurable FIR filter */ | |
| if (chip_info->fir_config_mask) { | |
| ret &= ~chip_info->fir_config_mask; | |
| ret |= field_prep(chip_info->fir_config_mask, MLX90614_CONST_FIR); | |
| } | |
| ret &= ~chip_info->iir_config_mask; | |
| ret |= field_prep(chip_info->iir_config_mask, i); | |
| /* Write changed values */ | |
| ret = mlx90614_write_word(client, chip_info->op_eeprom_config1, ret); | |
| return ret; | |
| } | |
| #ifdef CONFIG_PM | |
| /* | |
| * If @startup is true, make sure MLX90614_TIMING_STARTUP ms have elapsed since | |
| * the last wake-up. This is normally only needed to get a valid temperature | |
| * reading. EEPROM access does not need such delay. | |
| * Return 0 on success, <0 on error. | |
| */ | |
| static int mlx90614_power_get(struct mlx90614_data *data, bool startup) | |
| { | |
| unsigned long now; | |
| int ret; | |
| if (!data->wakeup_gpio) | |
| return 0; | |
| ret = pm_runtime_resume_and_get(&data->client->dev); | |
| if (ret < 0) | |
| return ret; | |
| if (startup) { | |
| now = jiffies; | |
| if (time_before(now, data->ready_timestamp) && | |
| msleep_interruptible(jiffies_to_msecs( | |
| data->ready_timestamp - now)) != 0) { | |
| pm_runtime_put_autosuspend(&data->client->dev); | |
| return -EINTR; | |
| } | |
| } | |
| return 0; | |
| } | |
| static void mlx90614_power_put(struct mlx90614_data *data) | |
| { | |
| if (!data->wakeup_gpio) | |
| return; | |
| pm_runtime_put_autosuspend(&data->client->dev); | |
| } | |
| #else | |
| static inline int mlx90614_power_get(struct mlx90614_data *data, bool startup) | |
| { | |
| return 0; | |
| } | |
| static inline void mlx90614_power_put(struct mlx90614_data *data) | |
| { | |
| } | |
| #endif | |
| static int mlx90614_read_raw(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *channel, int *val, | |
| int *val2, long mask) | |
| { | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| u8 cmd, idx; | |
| s32 ret; | |
| switch (mask) { | |
| case IIO_CHAN_INFO_RAW: /* 0.02K / LSB */ | |
| switch (channel->channel2) { | |
| case IIO_MOD_TEMP_AMBIENT: | |
| cmd = chip_info->op_ram_ta; | |
| break; | |
| case IIO_MOD_TEMP_OBJECT: | |
| if (chip_info->dual_channel && channel->channel) | |
| return -EINVAL; | |
| switch (channel->channel) { | |
| case 0: | |
| cmd = chip_info->op_ram_tobj1; | |
| break; | |
| case 1: | |
| cmd = chip_info->op_ram_tobj2; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| ret = mlx90614_power_get(data, true); | |
| if (ret < 0) | |
| return ret; | |
| ret = i2c_smbus_read_word_data(data->client, cmd); | |
| mlx90614_power_put(data); | |
| if (ret < 0) | |
| return ret; | |
| /* MSB is an error flag */ | |
| if (ret & 0x8000) | |
| return -EIO; | |
| *val = ret; | |
| return IIO_VAL_INT; | |
| case IIO_CHAN_INFO_OFFSET: | |
| *val = MLX90614_CONST_OFFSET_DEC; | |
| *val2 = MLX90614_CONST_OFFSET_REM; | |
| return IIO_VAL_INT_PLUS_MICRO; | |
| case IIO_CHAN_INFO_SCALE: | |
| *val = MLX90614_CONST_SCALE; | |
| return IIO_VAL_INT; | |
| case IIO_CHAN_INFO_CALIBEMISSIVITY: /* 1/emissivity_max / LSB */ | |
| ret = mlx90614_power_get(data, false); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&data->lock); | |
| ret = i2c_smbus_read_word_data(data->client, | |
| chip_info->op_eeprom_emissivity); | |
| mutex_unlock(&data->lock); | |
| mlx90614_power_put(data); | |
| if (ret < 0) | |
| return ret; | |
| if (ret == chip_info->emissivity_max) { | |
| *val = 1; | |
| *val2 = 0; | |
| } else { | |
| *val = 0; | |
| *val2 = ret * NSEC_PER_SEC / chip_info->emissivity_max; | |
| } | |
| return IIO_VAL_INT_PLUS_NANO; | |
| /* IIR setting with FIR=1024 (MLX90614) or FIR=65536 (MLX90615) */ | |
| case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: | |
| ret = mlx90614_power_get(data, false); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&data->lock); | |
| ret = i2c_smbus_read_word_data(data->client, | |
| chip_info->op_eeprom_config1); | |
| mutex_unlock(&data->lock); | |
| mlx90614_power_put(data); | |
| if (ret < 0) | |
| return ret; | |
| idx = field_get(chip_info->iir_config_mask, ret) - | |
| chip_info->iir_valid_offset; | |
| *val = chip_info->iir_values[idx] / 100; | |
| *val2 = (chip_info->iir_values[idx] % 100) * 10000; | |
| return IIO_VAL_INT_PLUS_MICRO; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int mlx90614_write_raw(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *channel, int val, | |
| int val2, long mask) | |
| { | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| s32 ret; | |
| switch (mask) { | |
| case IIO_CHAN_INFO_CALIBEMISSIVITY: /* 1/emissivity_max / LSB */ | |
| if (val < 0 || val2 < 0 || val > 1 || (val == 1 && val2 != 0)) | |
| return -EINVAL; | |
| val = val * chip_info->emissivity_max + | |
| val2 * chip_info->emissivity_max / NSEC_PER_SEC; | |
| ret = mlx90614_power_get(data, false); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&data->lock); | |
| ret = mlx90614_write_word(data->client, | |
| chip_info->op_eeprom_emissivity, val); | |
| mutex_unlock(&data->lock); | |
| mlx90614_power_put(data); | |
| return ret; | |
| case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR Filter setting */ | |
| if (val < 0 || val2 < 0) | |
| return -EINVAL; | |
| ret = mlx90614_power_get(data, false); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&data->lock); | |
| ret = mlx90614_iir_search(data->client, | |
| val * 100 + val2 / 10000); | |
| mutex_unlock(&data->lock); | |
| mlx90614_power_put(data); | |
| return ret; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int mlx90614_write_raw_get_fmt(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *channel, | |
| long mask) | |
| { | |
| switch (mask) { | |
| case IIO_CHAN_INFO_CALIBEMISSIVITY: | |
| return IIO_VAL_INT_PLUS_NANO; | |
| case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: | |
| return IIO_VAL_INT_PLUS_MICRO; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int mlx90614_read_avail(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *chan, | |
| const int **vals, int *type, int *length, | |
| long mask) | |
| { | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| switch (mask) { | |
| case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: | |
| *vals = (int *)chip_info->iir_freqs; | |
| *type = IIO_VAL_INT_PLUS_MICRO; | |
| *length = 2 * (ARRAY_SIZE(chip_info->iir_freqs) - | |
| chip_info->iir_valid_offset); | |
| return IIO_AVAIL_LIST; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static const struct iio_chan_spec mlx90614_channels[] = { | |
| { | |
| .type = IIO_TEMP, | |
| .modified = 1, | |
| .channel2 = IIO_MOD_TEMP_AMBIENT, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), | |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | | |
| BIT(IIO_CHAN_INFO_SCALE), | |
| }, | |
| { | |
| .type = IIO_TEMP, | |
| .modified = 1, | |
| .channel2 = IIO_MOD_TEMP_OBJECT, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | | |
| BIT(IIO_CHAN_INFO_CALIBEMISSIVITY) | | |
| BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), | |
| .info_mask_separate_available = | |
| BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), | |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | | |
| BIT(IIO_CHAN_INFO_SCALE), | |
| }, | |
| { | |
| .type = IIO_TEMP, | |
| .indexed = 1, | |
| .modified = 1, | |
| .channel = 1, | |
| .channel2 = IIO_MOD_TEMP_OBJECT, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | | |
| BIT(IIO_CHAN_INFO_CALIBEMISSIVITY) | | |
| BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), | |
| .info_mask_separate_available = | |
| BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), | |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) | | |
| BIT(IIO_CHAN_INFO_SCALE), | |
| }, | |
| }; | |
| static const struct iio_info mlx90614_info = { | |
| .read_raw = mlx90614_read_raw, | |
| .write_raw = mlx90614_write_raw, | |
| .write_raw_get_fmt = mlx90614_write_raw_get_fmt, | |
| .read_avail = mlx90614_read_avail, | |
| }; | |
| #ifdef CONFIG_PM | |
| static int mlx90614_sleep(struct mlx90614_data *data) | |
| { | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| s32 ret; | |
| if (!data->wakeup_gpio) { | |
| dev_dbg(&data->client->dev, "Sleep disabled"); | |
| return -ENOSYS; | |
| } | |
| dev_dbg(&data->client->dev, "Requesting sleep"); | |
| mutex_lock(&data->lock); | |
| ret = i2c_smbus_xfer(data->client->adapter, data->client->addr, | |
| data->client->flags | I2C_CLIENT_PEC, | |
| I2C_SMBUS_WRITE, chip_info->op_sleep, | |
| I2C_SMBUS_BYTE, NULL); | |
| mutex_unlock(&data->lock); | |
| return ret; | |
| } | |
| static int mlx90614_wakeup(struct mlx90614_data *data) | |
| { | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| if (!data->wakeup_gpio) { | |
| dev_dbg(&data->client->dev, "Wake-up disabled"); | |
| return -ENOSYS; | |
| } | |
| dev_dbg(&data->client->dev, "Requesting wake-up"); | |
| i2c_lock_bus(data->client->adapter, I2C_LOCK_ROOT_ADAPTER); | |
| gpiod_direction_output(data->wakeup_gpio, 0); | |
| msleep(chip_info->wakeup_delay_ms); | |
| gpiod_direction_input(data->wakeup_gpio); | |
| i2c_unlock_bus(data->client->adapter, I2C_LOCK_ROOT_ADAPTER); | |
| data->ready_timestamp = jiffies + | |
| msecs_to_jiffies(MLX90614_TIMING_STARTUP); | |
| /* | |
| * Quirk: the i2c controller may get confused right after the | |
| * wake-up signal has been sent. As a workaround, do a dummy read. | |
| * If the read fails, the controller will probably be reset so that | |
| * further reads will work. | |
| */ | |
| i2c_smbus_read_word_data(data->client, chip_info->op_eeprom_config1); | |
| return 0; | |
| } | |
| /* Return wake-up GPIO or NULL if sleep functionality should be disabled. */ | |
| static struct gpio_desc *mlx90614_probe_wakeup(struct i2c_client *client) | |
| { | |
| struct gpio_desc *gpio; | |
| if (!i2c_check_functionality(client->adapter, | |
| I2C_FUNC_SMBUS_WRITE_BYTE)) { | |
| dev_info(&client->dev, | |
| "i2c adapter does not support SMBUS_WRITE_BYTE, sleep disabled"); | |
| return NULL; | |
| } | |
| gpio = devm_gpiod_get_optional(&client->dev, "wakeup", GPIOD_IN); | |
| if (IS_ERR(gpio)) { | |
| dev_warn(&client->dev, | |
| "gpio acquisition failed with error %ld, sleep disabled", | |
| PTR_ERR(gpio)); | |
| return NULL; | |
| } else if (!gpio) { | |
| dev_info(&client->dev, | |
| "wakeup-gpio not found, sleep disabled"); | |
| } | |
| return gpio; | |
| } | |
| #else | |
| static inline int mlx90614_sleep(struct mlx90614_data *data) | |
| { | |
| return -ENOSYS; | |
| } | |
| static inline int mlx90614_wakeup(struct mlx90614_data *data) | |
| { | |
| return -ENOSYS; | |
| } | |
| static inline struct gpio_desc *mlx90614_probe_wakeup(struct i2c_client *client) | |
| { | |
| return NULL; | |
| } | |
| #endif | |
| /* Return 0 for single sensor, 1 for dual sensor, <0 on error. */ | |
| static int mlx90614_probe_num_ir_sensors(struct i2c_client *client) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| const struct mlx_chip_info *chip_info = data->chip_info; | |
| s32 ret; | |
| if (chip_info->dual_channel) | |
| return 0; | |
| ret = i2c_smbus_read_word_data(client, chip_info->op_eeprom_config1); | |
| if (ret < 0) | |
| return ret; | |
| return (ret & MLX90614_CONFIG_DUAL_MASK) ? 1 : 0; | |
| } | |
| static int mlx90614_probe(struct i2c_client *client) | |
| { | |
| const struct i2c_device_id *id = i2c_client_get_device_id(client); | |
| struct iio_dev *indio_dev; | |
| struct mlx90614_data *data; | |
| int ret; | |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA)) | |
| return -EOPNOTSUPP; | |
| indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); | |
| if (!indio_dev) | |
| return -ENOMEM; | |
| data = iio_priv(indio_dev); | |
| i2c_set_clientdata(client, indio_dev); | |
| data->client = client; | |
| mutex_init(&data->lock); | |
| data->wakeup_gpio = mlx90614_probe_wakeup(client); | |
| data->chip_info = i2c_get_match_data(client); | |
| mlx90614_wakeup(data); | |
| indio_dev->name = id->name; | |
| indio_dev->modes = INDIO_DIRECT_MODE; | |
| indio_dev->info = &mlx90614_info; | |
| ret = mlx90614_probe_num_ir_sensors(client); | |
| switch (ret) { | |
| case 0: | |
| dev_dbg(&client->dev, "Found single sensor"); | |
| indio_dev->channels = mlx90614_channels; | |
| indio_dev->num_channels = 2; | |
| break; | |
| case 1: | |
| dev_dbg(&client->dev, "Found dual sensor"); | |
| indio_dev->channels = mlx90614_channels; | |
| indio_dev->num_channels = 3; | |
| break; | |
| default: | |
| return ret; | |
| } | |
| if (data->wakeup_gpio) { | |
| pm_runtime_set_autosuspend_delay(&client->dev, | |
| MLX90614_AUTOSLEEP_DELAY); | |
| pm_runtime_use_autosuspend(&client->dev); | |
| pm_runtime_set_active(&client->dev); | |
| pm_runtime_enable(&client->dev); | |
| } | |
| return iio_device_register(indio_dev); | |
| } | |
| static void mlx90614_remove(struct i2c_client *client) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| iio_device_unregister(indio_dev); | |
| if (data->wakeup_gpio) { | |
| pm_runtime_disable(&client->dev); | |
| if (!pm_runtime_status_suspended(&client->dev)) | |
| mlx90614_sleep(data); | |
| pm_runtime_set_suspended(&client->dev); | |
| } | |
| } | |
| static const struct mlx_chip_info mlx90614_chip_info = { | |
| .op_eeprom_emissivity = MLX90614_OP_EEPROM | 0x04, | |
| .op_eeprom_config1 = MLX90614_OP_EEPROM | 0x05, | |
| .op_ram_ta = MLX90614_OP_RAM | 0x06, | |
| .op_ram_tobj1 = MLX90614_OP_RAM | 0x07, | |
| .op_ram_tobj2 = MLX90614_OP_RAM | 0x08, | |
| .op_sleep = MLX90614_OP_SLEEP, | |
| .dual_channel = true, | |
| .wakeup_delay_ms = MLX90614_TIMING_WAKEUP, | |
| .emissivity_max = 65535, | |
| .fir_config_mask = MLX90614_CONFIG_FIR_MASK, | |
| .iir_config_mask = MLX90614_CONFIG_IIR_MASK, | |
| .iir_valid_offset = 0, | |
| .iir_values = { 77, 31, 20, 15, 723, 153, 110, 86 }, | |
| .iir_freqs = { | |
| { 0, 150000 }, /* 13% ~= 0.15 Hz */ | |
| { 0, 200000 }, /* 17% ~= 0.20 Hz */ | |
| { 0, 310000 }, /* 25% ~= 0.31 Hz */ | |
| { 0, 770000 }, /* 50% ~= 0.77 Hz */ | |
| { 0, 860000 }, /* 57% ~= 0.86 Hz */ | |
| { 1, 100000 }, /* 67% ~= 1.10 Hz */ | |
| { 1, 530000 }, /* 80% ~= 1.53 Hz */ | |
| { 7, 230000 } /* 100% ~= 7.23 Hz */ | |
| }, | |
| }; | |
| static const struct mlx_chip_info mlx90615_chip_info = { | |
| .op_eeprom_emissivity = MLX90615_OP_EEPROM | 0x03, | |
| .op_eeprom_config1 = MLX90615_OP_EEPROM | 0x02, | |
| .op_ram_ta = MLX90615_OP_RAM | 0x06, | |
| .op_ram_tobj1 = MLX90615_OP_RAM | 0x07, | |
| .op_ram_tobj2 = MLX90615_OP_RAM | 0x08, | |
| .op_sleep = MLX90615_OP_SLEEP, | |
| .dual_channel = false, | |
| .wakeup_delay_ms = MLX90615_TIMING_WAKEUP, | |
| .emissivity_max = 16383, | |
| .fir_config_mask = 0, /* MLX90615 FIR is fixed */ | |
| .iir_config_mask = MLX90615_CONFIG_IIR_MASK, | |
| /* IIR value 0 is FORBIDDEN COMBINATION on MLX90615 */ | |
| .iir_valid_offset = 1, | |
| .iir_values = { 500, 50, 30, 20, 15, 13, 10 }, | |
| .iir_freqs = { | |
| { 0, 100000 }, /* 14% ~= 0.10 Hz */ | |
| { 0, 130000 }, /* 17% ~= 0.13 Hz */ | |
| { 0, 150000 }, /* 20% ~= 0.15 Hz */ | |
| { 0, 200000 }, /* 25% ~= 0.20 Hz */ | |
| { 0, 300000 }, /* 33% ~= 0.30 Hz */ | |
| { 0, 500000 }, /* 50% ~= 0.50 Hz */ | |
| { 5, 000000 }, /* 100% ~= 5.00 Hz */ | |
| }, | |
| }; | |
| static const struct i2c_device_id mlx90614_id[] = { | |
| { .name = "mlx90614", .driver_data = (kernel_ulong_t)&mlx90614_chip_info }, | |
| { .name = "mlx90615", .driver_data = (kernel_ulong_t)&mlx90615_chip_info }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, mlx90614_id); | |
| static const struct of_device_id mlx90614_of_match[] = { | |
| { .compatible = "melexis,mlx90614", .data = &mlx90614_chip_info }, | |
| { .compatible = "melexis,mlx90615", .data = &mlx90615_chip_info }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, mlx90614_of_match); | |
| static int mlx90614_pm_suspend(struct device *dev) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| if (data->wakeup_gpio && pm_runtime_active(dev)) | |
| return mlx90614_sleep(data); | |
| return 0; | |
| } | |
| static int mlx90614_pm_resume(struct device *dev) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| int err; | |
| if (data->wakeup_gpio) { | |
| err = mlx90614_wakeup(data); | |
| if (err < 0) | |
| return err; | |
| pm_runtime_disable(dev); | |
| pm_runtime_set_active(dev); | |
| pm_runtime_enable(dev); | |
| } | |
| return 0; | |
| } | |
| static int mlx90614_pm_runtime_suspend(struct device *dev) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| return mlx90614_sleep(data); | |
| } | |
| static int mlx90614_pm_runtime_resume(struct device *dev) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); | |
| struct mlx90614_data *data = iio_priv(indio_dev); | |
| return mlx90614_wakeup(data); | |
| } | |
| static const struct dev_pm_ops mlx90614_pm_ops = { | |
| SYSTEM_SLEEP_PM_OPS(mlx90614_pm_suspend, mlx90614_pm_resume) | |
| RUNTIME_PM_OPS(mlx90614_pm_runtime_suspend, | |
| mlx90614_pm_runtime_resume, NULL) | |
| }; | |
| static struct i2c_driver mlx90614_driver = { | |
| .driver = { | |
| .name = "mlx90614", | |
| .of_match_table = mlx90614_of_match, | |
| .pm = pm_ptr(&mlx90614_pm_ops), | |
| }, | |
| .probe = mlx90614_probe, | |
| .remove = mlx90614_remove, | |
| .id_table = mlx90614_id, | |
| }; | |
| module_i2c_driver(mlx90614_driver); | |
| MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>"); | |
| MODULE_AUTHOR("Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>"); | |
| MODULE_AUTHOR("Crt Mori <cmo@melexis.com>"); | |
| MODULE_DESCRIPTION("Melexis MLX90614 contactless IR temperature sensor driver"); | |
| MODULE_LICENSE("GPL"); |