| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * IIO driver for the light sensor ISL29028. | |
| * ISL29028 is Concurrent Ambient Light and Proximity Sensor | |
| * | |
| * Copyright (c) 2012, NVIDIA CORPORATION. All rights reserved. | |
| * Copyright (c) 2016-2017 Brian Masney <masneyb@onstation.org> | |
| * | |
| * Datasheets: | |
| * - http://www.intersil.com/content/dam/Intersil/documents/isl2/isl29028.pdf | |
| * - http://www.intersil.com/content/dam/Intersil/documents/isl2/isl29030.pdf | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/i2c.h> | |
| #include <linux/err.h> | |
| #include <linux/mutex.h> | |
| #include <linux/delay.h> | |
| #include <linux/slab.h> | |
| #include <linux/regmap.h> | |
| #include <linux/iio/iio.h> | |
| #include <linux/iio/sysfs.h> | |
| #include <linux/pm_runtime.h> | |
| #define ISL29028_CONV_TIME_MS 100 | |
| #define ISL29028_REG_CONFIGURE 0x01 | |
| #define ISL29028_CONF_ALS_IR_MODE_ALS 0 | |
| #define ISL29028_CONF_ALS_IR_MODE_IR BIT(0) | |
| #define ISL29028_CONF_ALS_IR_MODE_MASK BIT(0) | |
| #define ISL29028_CONF_ALS_RANGE_LOW_LUX 0 | |
| #define ISL29028_CONF_ALS_RANGE_HIGH_LUX BIT(1) | |
| #define ISL29028_CONF_ALS_RANGE_MASK BIT(1) | |
| #define ISL29028_CONF_ALS_DIS 0 | |
| #define ISL29028_CONF_ALS_EN BIT(2) | |
| #define ISL29028_CONF_ALS_EN_MASK BIT(2) | |
| #define ISL29028_CONF_PROX_SLP_SH 4 | |
| #define ISL29028_CONF_PROX_SLP_MASK (7 << ISL29028_CONF_PROX_SLP_SH) | |
| #define ISL29028_CONF_PROX_EN BIT(7) | |
| #define ISL29028_CONF_PROX_EN_MASK BIT(7) | |
| #define ISL29028_REG_INTERRUPT 0x02 | |
| #define ISL29028_REG_PROX_DATA 0x08 | |
| #define ISL29028_REG_ALSIR_L 0x09 | |
| #define ISL29028_REG_ALSIR_U 0x0A | |
| #define ISL29028_REG_TEST1_MODE 0x0E | |
| #define ISL29028_REG_TEST2_MODE 0x0F | |
| #define ISL29028_NUM_REGS (ISL29028_REG_TEST2_MODE + 1) | |
| #define ISL29028_POWER_OFF_DELAY_MS 2000 | |
| struct isl29028_prox_data { | |
| int sampling_int; | |
| int sampling_fract; | |
| int sleep_time; | |
| }; | |
| static const struct isl29028_prox_data isl29028_prox_data[] = { | |
| { 1, 250000, 800 }, | |
| { 2, 500000, 400 }, | |
| { 5, 0, 200 }, | |
| { 10, 0, 100 }, | |
| { 13, 300000, 75 }, | |
| { 20, 0, 50 }, | |
| { 80, 0, 13 }, /* | |
| * Note: Data sheet lists 12.5 ms sleep time. | |
| * Round up a half millisecond for msleep(). | |
| */ | |
| { 100, 0, 0 } | |
| }; | |
| enum isl29028_als_ir_mode { | |
| ISL29028_MODE_NONE = 0, | |
| ISL29028_MODE_ALS, | |
| ISL29028_MODE_IR, | |
| }; | |
| struct isl29028_chip { | |
| struct mutex lock; | |
| struct regmap *regmap; | |
| int prox_sampling_int; | |
| int prox_sampling_frac; | |
| bool enable_prox; | |
| int lux_scale; | |
| enum isl29028_als_ir_mode als_ir_mode; | |
| }; | |
| static int isl29028_find_prox_sleep_index(int sampling_int, int sampling_fract) | |
| { | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(isl29028_prox_data); ++i) { | |
| if (isl29028_prox_data[i].sampling_int == sampling_int && | |
| isl29028_prox_data[i].sampling_fract == sampling_fract) | |
| return i; | |
| } | |
| return -EINVAL; | |
| } | |
| static int isl29028_set_proxim_sampling(struct isl29028_chip *chip, | |
| int sampling_int, int sampling_fract) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int sleep_index, ret; | |
| sleep_index = isl29028_find_prox_sleep_index(sampling_int, | |
| sampling_fract); | |
| if (sleep_index < 0) | |
| return sleep_index; | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_PROX_SLP_MASK, | |
| sleep_index << ISL29028_CONF_PROX_SLP_SH); | |
| if (ret < 0) { | |
| dev_err(dev, "%s(): Error %d setting the proximity sampling\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| chip->prox_sampling_int = sampling_int; | |
| chip->prox_sampling_frac = sampling_fract; | |
| return ret; | |
| } | |
| static int isl29028_enable_proximity(struct isl29028_chip *chip) | |
| { | |
| int prox_index, ret; | |
| ret = isl29028_set_proxim_sampling(chip, chip->prox_sampling_int, | |
| chip->prox_sampling_frac); | |
| if (ret < 0) | |
| return ret; | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_PROX_EN_MASK, | |
| ISL29028_CONF_PROX_EN); | |
| if (ret < 0) | |
| return ret; | |
| /* Wait for conversion to be complete for first sample */ | |
| prox_index = isl29028_find_prox_sleep_index(chip->prox_sampling_int, | |
| chip->prox_sampling_frac); | |
| if (prox_index < 0) | |
| return prox_index; | |
| msleep(isl29028_prox_data[prox_index].sleep_time); | |
| return 0; | |
| } | |
| static int isl29028_set_als_scale(struct isl29028_chip *chip, int lux_scale) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int val = (lux_scale == 2000) ? ISL29028_CONF_ALS_RANGE_HIGH_LUX : | |
| ISL29028_CONF_ALS_RANGE_LOW_LUX; | |
| int ret; | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_RANGE_MASK, val); | |
| if (ret < 0) { | |
| dev_err(dev, "%s(): Error %d setting the ALS scale\n", __func__, | |
| ret); | |
| return ret; | |
| } | |
| chip->lux_scale = lux_scale; | |
| return ret; | |
| } | |
| static int isl29028_set_als_ir_mode(struct isl29028_chip *chip, | |
| enum isl29028_als_ir_mode mode) | |
| { | |
| int ret; | |
| if (chip->als_ir_mode == mode) | |
| return 0; | |
| ret = isl29028_set_als_scale(chip, chip->lux_scale); | |
| if (ret < 0) | |
| return ret; | |
| switch (mode) { | |
| case ISL29028_MODE_ALS: | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_IR_MODE_MASK, | |
| ISL29028_CONF_ALS_IR_MODE_ALS); | |
| if (ret < 0) | |
| return ret; | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_RANGE_MASK, | |
| ISL29028_CONF_ALS_RANGE_HIGH_LUX); | |
| break; | |
| case ISL29028_MODE_IR: | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_IR_MODE_MASK, | |
| ISL29028_CONF_ALS_IR_MODE_IR); | |
| break; | |
| case ISL29028_MODE_NONE: | |
| return regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_EN_MASK, | |
| ISL29028_CONF_ALS_DIS); | |
| } | |
| if (ret < 0) | |
| return ret; | |
| /* Enable the ALS/IR */ | |
| ret = regmap_update_bits(chip->regmap, ISL29028_REG_CONFIGURE, | |
| ISL29028_CONF_ALS_EN_MASK, | |
| ISL29028_CONF_ALS_EN); | |
| if (ret < 0) | |
| return ret; | |
| /* Need to wait for conversion time if ALS/IR mode enabled */ | |
| msleep(ISL29028_CONV_TIME_MS); | |
| chip->als_ir_mode = mode; | |
| return 0; | |
| } | |
| static int isl29028_read_als_ir(struct isl29028_chip *chip, int *als_ir) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| unsigned int lsb; | |
| unsigned int msb; | |
| int ret; | |
| ret = regmap_read(chip->regmap, ISL29028_REG_ALSIR_L, &lsb); | |
| if (ret < 0) { | |
| dev_err(dev, | |
| "%s(): Error %d reading register ALSIR_L\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| ret = regmap_read(chip->regmap, ISL29028_REG_ALSIR_U, &msb); | |
| if (ret < 0) { | |
| dev_err(dev, | |
| "%s(): Error %d reading register ALSIR_U\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| *als_ir = ((msb & 0xF) << 8) | (lsb & 0xFF); | |
| return 0; | |
| } | |
| static int isl29028_read_proxim(struct isl29028_chip *chip, int *prox) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| unsigned int data; | |
| int ret; | |
| if (!chip->enable_prox) { | |
| ret = isl29028_enable_proximity(chip); | |
| if (ret < 0) | |
| return ret; | |
| chip->enable_prox = true; | |
| } | |
| ret = regmap_read(chip->regmap, ISL29028_REG_PROX_DATA, &data); | |
| if (ret < 0) { | |
| dev_err(dev, "%s(): Error %d reading register PROX_DATA\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| *prox = data; | |
| return 0; | |
| } | |
| static int isl29028_als_get(struct isl29028_chip *chip, int *als_data) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int ret; | |
| int als_ir_data; | |
| ret = isl29028_set_als_ir_mode(chip, ISL29028_MODE_ALS); | |
| if (ret < 0) { | |
| dev_err(dev, "%s(): Error %d enabling ALS mode\n", __func__, | |
| ret); | |
| return ret; | |
| } | |
| ret = isl29028_read_als_ir(chip, &als_ir_data); | |
| if (ret < 0) | |
| return ret; | |
| /* | |
| * convert als data count to lux. | |
| * if lux_scale = 125, lux = count * 0.031 | |
| * if lux_scale = 2000, lux = count * 0.49 | |
| */ | |
| if (chip->lux_scale == 125) | |
| als_ir_data = (als_ir_data * 31) / 1000; | |
| else | |
| als_ir_data = (als_ir_data * 49) / 100; | |
| *als_data = als_ir_data; | |
| return 0; | |
| } | |
| static int isl29028_ir_get(struct isl29028_chip *chip, int *ir_data) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int ret; | |
| ret = isl29028_set_als_ir_mode(chip, ISL29028_MODE_IR); | |
| if (ret < 0) { | |
| dev_err(dev, "%s(): Error %d enabling IR mode\n", __func__, | |
| ret); | |
| return ret; | |
| } | |
| return isl29028_read_als_ir(chip, ir_data); | |
| } | |
| /* Channel IO */ | |
| static int isl29028_write_raw(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *chan, | |
| int val, int val2, long mask) | |
| { | |
| struct isl29028_chip *chip = iio_priv(indio_dev); | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int ret; | |
| ret = pm_runtime_resume_and_get(dev); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&chip->lock); | |
| ret = -EINVAL; | |
| switch (chan->type) { | |
| case IIO_PROXIMITY: | |
| if (mask != IIO_CHAN_INFO_SAMP_FREQ) { | |
| dev_err(dev, | |
| "%s(): proximity: Mask value 0x%08lx is not supported\n", | |
| __func__, mask); | |
| break; | |
| } | |
| if (val < 1 || val > 100) { | |
| dev_err(dev, | |
| "%s(): proximity: Sampling frequency %d is not in the range [1:100]\n", | |
| __func__, val); | |
| break; | |
| } | |
| ret = isl29028_set_proxim_sampling(chip, val, val2); | |
| break; | |
| case IIO_LIGHT: | |
| if (mask != IIO_CHAN_INFO_SCALE) { | |
| dev_err(dev, | |
| "%s(): light: Mask value 0x%08lx is not supported\n", | |
| __func__, mask); | |
| break; | |
| } | |
| if (val != 125 && val != 2000) { | |
| dev_err(dev, | |
| "%s(): light: Lux scale %d is not in the set {125, 2000}\n", | |
| __func__, val); | |
| break; | |
| } | |
| ret = isl29028_set_als_scale(chip, val); | |
| break; | |
| default: | |
| dev_err(dev, "%s(): Unsupported channel type %x\n", | |
| __func__, chan->type); | |
| break; | |
| } | |
| mutex_unlock(&chip->lock); | |
| if (ret < 0) | |
| return ret; | |
| ret = pm_runtime_put_autosuspend(dev); | |
| if (ret < 0) | |
| return ret; | |
| return 0; | |
| } | |
| static int isl29028_read_raw(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *chan, | |
| int *val, int *val2, long mask) | |
| { | |
| struct isl29028_chip *chip = iio_priv(indio_dev); | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int ret, pm_ret; | |
| ret = pm_runtime_resume_and_get(dev); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&chip->lock); | |
| ret = -EINVAL; | |
| switch (mask) { | |
| case IIO_CHAN_INFO_RAW: | |
| case IIO_CHAN_INFO_PROCESSED: | |
| switch (chan->type) { | |
| case IIO_LIGHT: | |
| ret = isl29028_als_get(chip, val); | |
| break; | |
| case IIO_INTENSITY: | |
| ret = isl29028_ir_get(chip, val); | |
| break; | |
| case IIO_PROXIMITY: | |
| ret = isl29028_read_proxim(chip, val); | |
| break; | |
| default: | |
| break; | |
| } | |
| if (ret < 0) | |
| break; | |
| ret = IIO_VAL_INT; | |
| break; | |
| case IIO_CHAN_INFO_SAMP_FREQ: | |
| if (chan->type != IIO_PROXIMITY) | |
| break; | |
| *val = chip->prox_sampling_int; | |
| *val2 = chip->prox_sampling_frac; | |
| ret = IIO_VAL_INT; | |
| break; | |
| case IIO_CHAN_INFO_SCALE: | |
| if (chan->type != IIO_LIGHT) | |
| break; | |
| *val = chip->lux_scale; | |
| ret = IIO_VAL_INT; | |
| break; | |
| default: | |
| dev_err(dev, "%s(): mask value 0x%08lx is not supported\n", | |
| __func__, mask); | |
| break; | |
| } | |
| mutex_unlock(&chip->lock); | |
| if (ret < 0) | |
| return ret; | |
| /** | |
| * Preserve the ret variable if the call to | |
| * pm_runtime_put_autosuspend() is successful so the reading | |
| * (if applicable) is returned to user space. | |
| */ | |
| pm_ret = pm_runtime_put_autosuspend(dev); | |
| if (pm_ret < 0) | |
| return pm_ret; | |
| return ret; | |
| } | |
| static IIO_CONST_ATTR(in_proximity_sampling_frequency_available, | |
| "1.25 2.5 5 10 13.3 20 80 100"); | |
| static IIO_CONST_ATTR(in_illuminance_scale_available, "125 2000"); | |
| #define ISL29028_CONST_ATTR(name) (&iio_const_attr_##name.dev_attr.attr) | |
| static struct attribute *isl29028_attributes[] = { | |
| ISL29028_CONST_ATTR(in_proximity_sampling_frequency_available), | |
| ISL29028_CONST_ATTR(in_illuminance_scale_available), | |
| NULL, | |
| }; | |
| static const struct attribute_group isl29108_group = { | |
| .attrs = isl29028_attributes, | |
| }; | |
| static const struct iio_chan_spec isl29028_channels[] = { | |
| { | |
| .type = IIO_LIGHT, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | | |
| BIT(IIO_CHAN_INFO_SCALE), | |
| }, { | |
| .type = IIO_INTENSITY, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), | |
| }, { | |
| .type = IIO_PROXIMITY, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | | |
| BIT(IIO_CHAN_INFO_SAMP_FREQ), | |
| } | |
| }; | |
| static const struct iio_info isl29028_info = { | |
| .attrs = &isl29108_group, | |
| .read_raw = isl29028_read_raw, | |
| .write_raw = isl29028_write_raw, | |
| }; | |
| static int isl29028_clear_configure_reg(struct isl29028_chip *chip) | |
| { | |
| struct device *dev = regmap_get_device(chip->regmap); | |
| int ret; | |
| ret = regmap_write(chip->regmap, ISL29028_REG_CONFIGURE, 0x0); | |
| if (ret < 0) | |
| dev_err(dev, "%s(): Error %d clearing the CONFIGURE register\n", | |
| __func__, ret); | |
| chip->als_ir_mode = ISL29028_MODE_NONE; | |
| chip->enable_prox = false; | |
| return ret; | |
| } | |
| static bool isl29028_is_volatile_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case ISL29028_REG_INTERRUPT: | |
| case ISL29028_REG_PROX_DATA: | |
| case ISL29028_REG_ALSIR_L: | |
| case ISL29028_REG_ALSIR_U: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static const struct regmap_config isl29028_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .volatile_reg = isl29028_is_volatile_reg, | |
| .max_register = ISL29028_NUM_REGS - 1, | |
| .num_reg_defaults_raw = ISL29028_NUM_REGS, | |
| .cache_type = REGCACHE_MAPLE, | |
| }; | |
| static int isl29028_probe(struct i2c_client *client) | |
| { | |
| const struct i2c_device_id *id = i2c_client_get_device_id(client); | |
| struct isl29028_chip *chip; | |
| struct iio_dev *indio_dev; | |
| int ret; | |
| indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); | |
| if (!indio_dev) | |
| return -ENOMEM; | |
| chip = iio_priv(indio_dev); | |
| i2c_set_clientdata(client, indio_dev); | |
| mutex_init(&chip->lock); | |
| chip->regmap = devm_regmap_init_i2c(client, &isl29028_regmap_config); | |
| if (IS_ERR(chip->regmap)) { | |
| ret = PTR_ERR(chip->regmap); | |
| dev_err(&client->dev, "%s: Error %d initializing regmap\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| chip->enable_prox = false; | |
| chip->prox_sampling_int = 20; | |
| chip->prox_sampling_frac = 0; | |
| chip->lux_scale = 2000; | |
| ret = regmap_write(chip->regmap, ISL29028_REG_TEST1_MODE, 0x0); | |
| if (ret < 0) { | |
| dev_err(&client->dev, | |
| "%s(): Error %d writing to TEST1_MODE register\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| ret = regmap_write(chip->regmap, ISL29028_REG_TEST2_MODE, 0x0); | |
| if (ret < 0) { | |
| dev_err(&client->dev, | |
| "%s(): Error %d writing to TEST2_MODE register\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| ret = isl29028_clear_configure_reg(chip); | |
| if (ret < 0) | |
| return ret; | |
| indio_dev->info = &isl29028_info; | |
| indio_dev->channels = isl29028_channels; | |
| indio_dev->num_channels = ARRAY_SIZE(isl29028_channels); | |
| indio_dev->name = id->name; | |
| indio_dev->modes = INDIO_DIRECT_MODE; | |
| pm_runtime_enable(&client->dev); | |
| pm_runtime_set_autosuspend_delay(&client->dev, | |
| ISL29028_POWER_OFF_DELAY_MS); | |
| pm_runtime_use_autosuspend(&client->dev); | |
| ret = iio_device_register(indio_dev); | |
| if (ret < 0) { | |
| dev_err(&client->dev, | |
| "%s(): iio registration failed with error %d\n", | |
| __func__, ret); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static void isl29028_remove(struct i2c_client *client) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); | |
| struct isl29028_chip *chip = iio_priv(indio_dev); | |
| iio_device_unregister(indio_dev); | |
| pm_runtime_disable(&client->dev); | |
| pm_runtime_set_suspended(&client->dev); | |
| isl29028_clear_configure_reg(chip); | |
| } | |
| static int isl29028_suspend(struct device *dev) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); | |
| struct isl29028_chip *chip = iio_priv(indio_dev); | |
| int ret; | |
| mutex_lock(&chip->lock); | |
| ret = isl29028_clear_configure_reg(chip); | |
| mutex_unlock(&chip->lock); | |
| return ret; | |
| } | |
| static int isl29028_resume(struct device *dev) | |
| { | |
| /** | |
| * The specific component (ALS/IR or proximity) will enable itself as | |
| * needed the next time that the user requests a reading. This is done | |
| * above in isl29028_set_als_ir_mode() and isl29028_enable_proximity(). | |
| */ | |
| return 0; | |
| } | |
| static DEFINE_RUNTIME_DEV_PM_OPS(isl29028_pm_ops, isl29028_suspend, | |
| isl29028_resume, NULL); | |
| static const struct i2c_device_id isl29028_id[] = { | |
| { .name = "isl29028" }, | |
| { .name = "isl29030" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, isl29028_id); | |
| static const struct of_device_id isl29028_of_match[] = { | |
| { .compatible = "isl,isl29028", }, /* for backward compat., don't use */ | |
| { .compatible = "isil,isl29028", }, | |
| { .compatible = "isil,isl29030", }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, isl29028_of_match); | |
| static struct i2c_driver isl29028_driver = { | |
| .driver = { | |
| .name = "isl29028", | |
| .pm = pm_ptr(&isl29028_pm_ops), | |
| .of_match_table = isl29028_of_match, | |
| }, | |
| .probe = isl29028_probe, | |
| .remove = isl29028_remove, | |
| .id_table = isl29028_id, | |
| }; | |
| module_i2c_driver(isl29028_driver); | |
| MODULE_DESCRIPTION("ISL29028 Ambient Light and Proximity Sensor driver"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>"); |