| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * drivers/i2c/busses/i2c-tegra.c | |
| * | |
| * Copyright (C) 2010 Google, Inc. | |
| * Author: Colin Cross <ccross@android.com> | |
| */ | |
| #include <linux/acpi.h> | |
| #include <linux/bitfield.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/dmaengine.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/err.h> | |
| #include <linux/i2c.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/irq.h> | |
| #include <linux/kernel.h> | |
| #include <linux/ktime.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/pinctrl/consumer.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pm_runtime.h> | |
| #include <linux/reset.h> | |
| #define BYTES_PER_FIFO_WORD 4 | |
| #define I2C_CNFG_DEBOUNCE_CNT GENMASK(14, 12) | |
| #define I2C_CNFG_PACKET_MODE_EN BIT(10) | |
| #define I2C_CNFG_NEW_MASTER_FSM BIT(11) | |
| #define I2C_CNFG_MULTI_MASTER_MODE BIT(17) | |
| #define I2C_SL_CNFG_NACK BIT(1) | |
| #define I2C_SL_CNFG_NEWSL BIT(2) | |
| #define I2C_FIFO_CONTROL_TX_FLUSH BIT(1) | |
| #define I2C_FIFO_CONTROL_RX_FLUSH BIT(0) | |
| #define I2C_FIFO_CONTROL_TX_TRIG(x) (((x) - 1) << 5) | |
| #define I2C_FIFO_CONTROL_RX_TRIG(x) (((x) - 1) << 2) | |
| #define I2C_FIFO_STATUS_TX GENMASK(7, 4) | |
| #define I2C_FIFO_STATUS_RX GENMASK(3, 0) | |
| #define I2C_INT_BUS_CLR_DONE BIT(11) | |
| #define I2C_INT_PACKET_XFER_COMPLETE BIT(7) | |
| #define I2C_INT_NO_ACK BIT(3) | |
| #define I2C_INT_ARBITRATION_LOST BIT(2) | |
| #define I2C_INT_TX_FIFO_DATA_REQ BIT(1) | |
| #define I2C_INT_RX_FIFO_DATA_REQ BIT(0) | |
| #define I2C_CLK_DIVISOR_STD_FAST_MODE GENMASK(31, 16) | |
| #define I2C_CLK_DIVISOR_HSMODE GENMASK(15, 0) | |
| #define DVC_CTRL_REG1 0x000 | |
| #define DVC_CTRL_REG1_INTR_EN BIT(10) | |
| #define DVC_CTRL_REG3 0x008 | |
| #define DVC_CTRL_REG3_SW_PROG BIT(26) | |
| #define DVC_CTRL_REG3_I2C_DONE_INTR_EN BIT(30) | |
| #define DVC_STATUS 0x00c | |
| #define DVC_STATUS_I2C_DONE_INTR BIT(30) | |
| #define I2C_ERR_NONE 0x00 | |
| #define I2C_ERR_NO_ACK BIT(0) | |
| #define I2C_ERR_ARBITRATION_LOST BIT(1) | |
| #define I2C_ERR_UNKNOWN_INTERRUPT BIT(2) | |
| #define I2C_ERR_RX_BUFFER_OVERFLOW BIT(3) | |
| #define PACKET_HEADER0_HEADER_SIZE GENMASK(29, 28) | |
| #define PACKET_HEADER0_PACKET_ID GENMASK(23, 16) | |
| #define PACKET_HEADER0_CONT_ID GENMASK(15, 12) | |
| #define PACKET_HEADER0_PROTOCOL GENMASK(7, 4) | |
| #define PACKET_HEADER0_PROTOCOL_I2C 1 | |
| #define I2C_HEADER_HS_MODE BIT(22) | |
| #define I2C_HEADER_CONT_ON_NAK BIT(21) | |
| #define I2C_HEADER_READ BIT(19) | |
| #define I2C_HEADER_10BIT_ADDR BIT(18) | |
| #define I2C_HEADER_IE_ENABLE BIT(17) | |
| #define I2C_HEADER_REPEAT_START BIT(16) | |
| #define I2C_HEADER_CONTINUE_XFER BIT(15) | |
| #define I2C_HEADER_SLAVE_ADDR_SHIFT 1 | |
| #define I2C_BC_SCLK_THRESHOLD GENMASK(23, 16) | |
| #define I2C_BC_STOP_COND BIT(2) | |
| #define I2C_BC_TERMINATE BIT(1) | |
| #define I2C_BC_ENABLE BIT(0) | |
| #define I2C_BC_STATUS BIT(0) | |
| #define I2C_MSTR_CONFIG_LOAD BIT(0) | |
| #define I2C_MST_CORE_CLKEN_OVR BIT(0) | |
| #define I2C_INTERFACE_TIMING_THIGH GENMASK(13, 8) | |
| #define I2C_INTERFACE_TIMING_TLOW GENMASK(5, 0) | |
| #define I2C_INTERFACE_TIMING_TBUF GENMASK(29, 24) | |
| #define I2C_INTERFACE_TIMING_TSU_STO GENMASK(21, 16) | |
| #define I2C_INTERFACE_TIMING_THD_STA GENMASK(13, 8) | |
| #define I2C_INTERFACE_TIMING_TSU_STA GENMASK(5, 0) | |
| #define I2C_HS_INTERFACE_TIMING_THIGH GENMASK(13, 8) | |
| #define I2C_HS_INTERFACE_TIMING_TLOW GENMASK(5, 0) | |
| #define I2C_HS_INTERFACE_TIMING_TSU_STO GENMASK(21, 16) | |
| #define I2C_HS_INTERFACE_TIMING_THD_STA GENMASK(13, 8) | |
| #define I2C_HS_INTERFACE_TIMING_TSU_STA GENMASK(5, 0) | |
| #define I2C_MST_FIFO_CONTROL_RX_FLUSH BIT(0) | |
| #define I2C_MST_FIFO_CONTROL_TX_FLUSH BIT(1) | |
| #define I2C_MST_FIFO_CONTROL_RX_TRIG(x) (((x) - 1) << 4) | |
| #define I2C_MST_FIFO_CONTROL_TX_TRIG(x) (((x) - 1) << 16) | |
| #define I2C_MST_FIFO_STATUS_TX GENMASK(23, 16) | |
| #define I2C_MST_FIFO_STATUS_RX GENMASK(7, 0) | |
| #define I2C_SW_MUTEX_REQUEST GENMASK(3, 0) | |
| #define I2C_SW_MUTEX_GRANT GENMASK(7, 4) | |
| #define I2C_SW_MUTEX_ID_CCPLEX 9 | |
| /* SW mutex acquire timeout value in microseconds. */ | |
| #define I2C_SW_MUTEX_TIMEOUT_US (25 * USEC_PER_MSEC) | |
| /* configuration load timeout in microseconds */ | |
| #define I2C_CONFIG_LOAD_TIMEOUT 1000000 | |
| /* packet header size in bytes */ | |
| #define I2C_PACKET_HEADER_SIZE 12 | |
| /* | |
| * I2C Controller will use PIO mode for transfers up to 32 bytes in order to | |
| * avoid DMA overhead, otherwise external APB DMA controller will be used. | |
| * Note that the actual MAX PIO length is 20 bytes because 32 bytes include | |
| * I2C_PACKET_HEADER_SIZE. | |
| */ | |
| #define I2C_PIO_MODE_PREFERRED_LEN 32 | |
| struct tegra_i2c_regs { | |
| unsigned int cnfg; | |
| unsigned int status; | |
| unsigned int sl_cnfg; | |
| unsigned int sl_addr1; | |
| unsigned int sl_addr2; | |
| unsigned int tlow_sext; | |
| unsigned int tx_fifo; | |
| unsigned int rx_fifo; | |
| unsigned int packet_transfer_status; | |
| unsigned int fifo_control; | |
| unsigned int fifo_status; | |
| unsigned int int_mask; | |
| unsigned int int_status; | |
| unsigned int clk_divisor; | |
| unsigned int bus_clear_cnfg; | |
| unsigned int bus_clear_status; | |
| unsigned int config_load; | |
| unsigned int clken_override; | |
| unsigned int interface_timing_0; | |
| unsigned int interface_timing_1; | |
| unsigned int hs_interface_timing_0; | |
| unsigned int hs_interface_timing_1; | |
| unsigned int master_reset_cntrl; | |
| unsigned int mst_fifo_control; | |
| unsigned int mst_fifo_status; | |
| unsigned int fairness_arb; | |
| unsigned int sw_mutex; | |
| }; | |
| static const struct tegra_i2c_regs tegra20_i2c_regs = { | |
| .cnfg = 0x000, | |
| .status = 0x01c, | |
| .sl_cnfg = 0x020, | |
| .sl_addr1 = 0x02c, | |
| .sl_addr2 = 0x030, | |
| .tx_fifo = 0x050, | |
| .rx_fifo = 0x054, | |
| .packet_transfer_status = 0x058, | |
| .fifo_control = 0x05c, | |
| .fifo_status = 0x060, | |
| .int_mask = 0x064, | |
| .int_status = 0x068, | |
| .clk_divisor = 0x06c, | |
| .bus_clear_cnfg = 0x084, | |
| .bus_clear_status = 0x088, | |
| .config_load = 0x08c, | |
| .clken_override = 0x090, | |
| .interface_timing_0 = 0x094, | |
| .interface_timing_1 = 0x098, | |
| .hs_interface_timing_0 = 0x09c, | |
| .hs_interface_timing_1 = 0x0a0, | |
| .master_reset_cntrl = 0x0a8, | |
| .mst_fifo_control = 0x0b4, | |
| .mst_fifo_status = 0x0b8, | |
| }; | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) | |
| static const struct tegra_i2c_regs tegra20_dvc_i2c_regs = { | |
| .cnfg = 0x040, | |
| .status = 0x05c, | |
| .tx_fifo = 0x060, | |
| .rx_fifo = 0x064, | |
| .packet_transfer_status = 0x068, | |
| .fifo_control = 0x06c, | |
| .fifo_status = 0x070, | |
| .int_mask = 0x074, | |
| .int_status = 0x078, | |
| .clk_divisor = 0x07c, | |
| .bus_clear_cnfg = 0x094, | |
| .bus_clear_status = 0x098, | |
| .config_load = 0x09c, | |
| .clken_override = 0x0a0, | |
| .interface_timing_0 = 0x0a4, | |
| .interface_timing_1 = 0x0a8, | |
| .hs_interface_timing_0 = 0x0ac, | |
| .hs_interface_timing_1 = 0x0b0, | |
| .master_reset_cntrl = 0x0b8, | |
| .mst_fifo_control = 0x0c4, | |
| .mst_fifo_status = 0x0c8, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC) | |
| static const struct tegra_i2c_regs tegra210_vi_i2c_regs = { | |
| .cnfg = 0x0c00, | |
| .status = 0x0c70, | |
| .tlow_sext = 0x0cd0, | |
| .tx_fifo = 0x0d40, | |
| .rx_fifo = 0x0d50, | |
| .packet_transfer_status = 0x0d60, | |
| .fifo_control = 0x0d70, | |
| .fifo_status = 0x0d80, | |
| .int_mask = 0x0d90, | |
| .int_status = 0x0da0, | |
| .clk_divisor = 0x0db0, | |
| .bus_clear_cnfg = 0x0e10, | |
| .bus_clear_status = 0x0e20, | |
| .config_load = 0x0e30, | |
| .clken_override = 0x0e40, | |
| .interface_timing_0 = 0x0e50, | |
| .interface_timing_1 = 0x0e60, | |
| .hs_interface_timing_0 = 0x0e70, | |
| .hs_interface_timing_1 = 0x0e80, | |
| .master_reset_cntrl = 0x0ea0, | |
| .mst_fifo_control = 0x0ed0, | |
| .mst_fifo_status = 0x0ee0, | |
| }; | |
| #endif | |
| static const struct tegra_i2c_regs tegra264_i2c_regs = { | |
| .cnfg = 0x000, | |
| .status = 0x01c, | |
| .sl_cnfg = 0x020, | |
| .sl_addr1 = 0x02c, | |
| .sl_addr2 = 0x030, | |
| .tx_fifo = 0x050, | |
| .rx_fifo = 0x054, | |
| .packet_transfer_status = 0x058, | |
| .fifo_control = 0x05c, | |
| .fifo_status = 0x060, | |
| .int_mask = 0x064, | |
| .int_status = 0x068, | |
| .clk_divisor = 0x06c, | |
| .bus_clear_cnfg = 0x084, | |
| .bus_clear_status = 0x088, | |
| .config_load = 0x08c, | |
| .clken_override = 0x090, | |
| .interface_timing_0 = 0x094, | |
| .interface_timing_1 = 0x098, | |
| .hs_interface_timing_0 = 0x09c, | |
| .hs_interface_timing_1 = 0x0a0, | |
| .master_reset_cntrl = 0x0a8, | |
| .mst_fifo_control = 0x0b4, | |
| .mst_fifo_status = 0x0b8, | |
| .fairness_arb = 0x0e8, | |
| .sw_mutex = 0x0ec, | |
| }; | |
| static const struct tegra_i2c_regs tegra410_i2c_regs = { | |
| .cnfg = 0x000, | |
| .status = 0x01c, | |
| .sl_cnfg = 0x020, | |
| .sl_addr1 = 0x02c, | |
| .sl_addr2 = 0x030, | |
| .tx_fifo = 0x054, | |
| .rx_fifo = 0x058, | |
| .packet_transfer_status = 0x05c, | |
| .fifo_control = 0x060, | |
| .fifo_status = 0x064, | |
| .int_mask = 0x068, | |
| .int_status = 0x06c, | |
| .clk_divisor = 0x070, | |
| .bus_clear_cnfg = 0x088, | |
| .bus_clear_status = 0x08c, | |
| .config_load = 0x090, | |
| .clken_override = 0x094, | |
| .interface_timing_0 = 0x098, | |
| .interface_timing_1 = 0x09c, | |
| .hs_interface_timing_0 = 0x0a0, | |
| .hs_interface_timing_1 = 0x0a4, | |
| .master_reset_cntrl = 0x0ac, | |
| .mst_fifo_control = 0x0b8, | |
| .mst_fifo_status = 0x0bc, | |
| .fairness_arb = 0x0ec, | |
| .sw_mutex = 0x0f0, | |
| }; | |
| /* | |
| * msg_end_type: The bus control which needs to be sent at end of transfer. | |
| * @MSG_END_STOP: Send stop pulse. | |
| * @MSG_END_REPEAT_START: Send repeat-start. | |
| * @MSG_END_CONTINUE: Don't send stop or repeat-start. | |
| */ | |
| enum msg_end_type { | |
| MSG_END_STOP, | |
| MSG_END_REPEAT_START, | |
| MSG_END_CONTINUE, | |
| }; | |
| /* | |
| * tegra_i2c_variant: Identifies the variant of I2C controller. | |
| * @TEGRA_I2C_VARIANT_DEFAULT: Identifies the default I2C controller. | |
| * @TEGRA_I2C_VARIANT_DVC: Identifies the DVC I2C controller, has a different register layout. | |
| * @TEGRA_I2C_VARIANT_VI: Identifies the VI I2C controller, has a different register layout. | |
| */ | |
| enum tegra_i2c_variant { | |
| TEGRA_I2C_VARIANT_DEFAULT, | |
| TEGRA_I2C_VARIANT_DVC, | |
| TEGRA_I2C_VARIANT_VI, | |
| }; | |
| /** | |
| * struct tegra_i2c_hw_feature : per hardware generation features | |
| * @has_continue_xfer_support: continue-transfer supported | |
| * @has_per_pkt_xfer_complete_irq: Has enable/disable capability for transfer | |
| * completion interrupt on per packet basis. | |
| * @has_config_load_reg: Has the config load register to load the new | |
| * configuration. | |
| * @clk_divisor_hs_mode: Clock divisor in HS mode. | |
| * @clk_divisor_std_mode: Clock divisor in standard mode. It is | |
| * applicable if there is no fast clock source i.e. single clock | |
| * source. | |
| * @clk_divisor_fast_mode: Clock divisor in fast mode. It is | |
| * applicable if there is no fast clock source i.e. single clock | |
| * source. | |
| * @clk_divisor_fast_plus_mode: Clock divisor in fast mode plus. It is | |
| * applicable if there is no fast clock source (i.e. single | |
| * clock source). | |
| * @has_multi_master_mode: The I2C controller supports running in single-master | |
| * or multi-master mode. | |
| * @has_slcg_override_reg: The I2C controller supports a register that | |
| * overrides the second level clock gating. | |
| * @has_mst_fifo: The I2C controller contains the new MST FIFO interface that | |
| * provides additional features and allows for longer messages to | |
| * be transferred in one go. | |
| * @has_mst_reset: The I2C controller contains MASTER_RESET_CTRL register which | |
| * provides an alternative to controller reset when configured as | |
| * I2C master | |
| * @quirks: I2C adapter quirks for limiting write/read transfer size and not | |
| * allowing 0 length transfers. | |
| * @supports_bus_clear: Bus Clear support to recover from bus hang during | |
| * SDA stuck low from device for some unknown reasons. | |
| * @has_apb_dma: Support of APBDMA on corresponding Tegra chip. | |
| * @tlow_std_mode: Low period of the clock in standard mode. | |
| * @thigh_std_mode: High period of the clock in standard mode. | |
| * @tlow_fast_mode: Low period of the clock in fast mode. | |
| * @thigh_fast_mode: High period of the clock in fast mode. | |
| * @tlow_fastplus_mode: Low period of the clock in fast-plus mode. | |
| * @thigh_fastplus_mode: High period of the clock in fast-plus mode. | |
| * @tlow_hs_mode: Low period of the clock in HS mode. | |
| * @thigh_hs_mode: High period of the clock in HS mode. | |
| * @setup_hold_time_std_mode: Setup and hold time for start and stop conditions | |
| * in standard mode. | |
| * @setup_hold_time_fast_mode: Setup and hold time for start and stop | |
| * conditions in fast mode. | |
| * @setup_hold_time_fastplus_mode: Setup and hold time for start and stop | |
| * conditions in fast-plus mode. | |
| * @setup_hold_time_hs_mode: Setup and hold time for start and stop conditions | |
| * in HS mode. | |
| * @has_interface_timing_reg: Has interface timing register to program the tuned | |
| * timing settings. | |
| * @enable_hs_mode_support: Enable support for high speed (HS) mode transfers. | |
| * @has_mutex: Has mutex register for mutual exclusion with other firmwares or VMs. | |
| * @has_fairarb_reg: Has fairness arbitration register for SMBUS/MCTP support. | |
| * @variant: This represents the I2C controller variant. | |
| * @regs: Register offsets for the specific SoC variant. | |
| */ | |
| struct tegra_i2c_hw_feature { | |
| bool has_continue_xfer_support; | |
| bool has_per_pkt_xfer_complete_irq; | |
| bool has_config_load_reg; | |
| u32 clk_divisor_hs_mode; | |
| u32 clk_divisor_std_mode; | |
| u32 clk_divisor_fast_mode; | |
| u32 clk_divisor_fast_plus_mode; | |
| bool has_multi_master_mode; | |
| bool has_slcg_override_reg; | |
| bool has_mst_fifo; | |
| bool has_mst_reset; | |
| const struct i2c_adapter_quirks *quirks; | |
| bool supports_bus_clear; | |
| bool has_apb_dma; | |
| u32 tlow_std_mode; | |
| u32 thigh_std_mode; | |
| u32 tlow_fast_mode; | |
| u32 thigh_fast_mode; | |
| u32 tlow_fastplus_mode; | |
| u32 thigh_fastplus_mode; | |
| u32 tlow_hs_mode; | |
| u32 thigh_hs_mode; | |
| u32 setup_hold_time_std_mode; | |
| u32 setup_hold_time_fast_mode; | |
| u32 setup_hold_time_fastplus_mode; | |
| u32 setup_hold_time_hs_mode; | |
| bool has_interface_timing_reg; | |
| bool enable_hs_mode_support; | |
| bool has_mutex; | |
| bool has_fairarb_reg; | |
| enum tegra_i2c_variant variant; | |
| const struct tegra_i2c_regs *regs; | |
| }; | |
| /** | |
| * struct tegra_i2c_dev - per device I2C context | |
| * @dev: device reference for power management | |
| * @hw: Tegra I2C HW feature | |
| * @adapter: core I2C layer adapter information | |
| * @div_clk: clock reference for div clock of I2C controller | |
| * @clocks: array of I2C controller clocks | |
| * @nclocks: number of clocks in the array | |
| * @base: ioremapped registers cookie | |
| * @base_phys: physical base address of the I2C controller | |
| * @cont_id: I2C controller ID, used for packet header | |
| * @irq: IRQ number of transfer complete interrupt | |
| * @msg_complete: transfer completion notifier | |
| * @msg_buf_remaining: size of unsent data in the message buffer | |
| * @msg_len: length of message in current transfer | |
| * @msg_err: error code for completed message | |
| * @msg_buf: pointer to current message data | |
| * @msg_read: indicates that the transfer is a read access | |
| * @timings: i2c timings information like bus frequency | |
| * @multimaster_mode: indicates that I2C controller is in multi-master mode | |
| * @is_mctp: indicates that the I2C controller is used as an MCTP controller | |
| * @dma_chan: DMA channel | |
| * @dma_phys: handle to DMA resources | |
| * @dma_buf: pointer to allocated DMA buffer | |
| * @dma_buf_size: DMA buffer size | |
| * @dma_dev: DMA device used for transfers | |
| * @dma_mode: indicates active DMA transfer | |
| * @dma_complete: DMA completion notifier | |
| * @atomic_mode: indicates active atomic transfer | |
| */ | |
| struct tegra_i2c_dev { | |
| struct device *dev; | |
| struct i2c_adapter adapter; | |
| const struct tegra_i2c_hw_feature *hw; | |
| unsigned int cont_id; | |
| unsigned int irq; | |
| phys_addr_t base_phys; | |
| void __iomem *base; | |
| struct clk_bulk_data clocks[2]; | |
| unsigned int nclocks; | |
| struct clk *div_clk; | |
| struct i2c_timings timings; | |
| struct completion msg_complete; | |
| size_t msg_buf_remaining; | |
| unsigned int msg_len; | |
| int msg_err; | |
| u8 *msg_buf; | |
| struct completion dma_complete; | |
| struct dma_chan *dma_chan; | |
| unsigned int dma_buf_size; | |
| struct device *dma_dev; | |
| dma_addr_t dma_phys; | |
| void *dma_buf; | |
| bool multimaster_mode; | |
| bool is_mctp; | |
| bool atomic_mode; | |
| bool dma_mode; | |
| bool msg_read; | |
| }; | |
| #define IS_DVC(dev) (IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) && \ | |
| (dev)->hw->variant == TEGRA_I2C_VARIANT_DVC) | |
| #define IS_VI(dev) (IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC) && \ | |
| (dev)->hw->variant == TEGRA_I2C_VARIANT_VI) | |
| static void dvc_writel(struct tegra_i2c_dev *i2c_dev, u32 val, | |
| unsigned int reg) | |
| { | |
| writel_relaxed(val, i2c_dev->base + reg); | |
| } | |
| static u32 dvc_readl(struct tegra_i2c_dev *i2c_dev, unsigned int reg) | |
| { | |
| return readl_relaxed(i2c_dev->base + reg); | |
| } | |
| static void i2c_writel(struct tegra_i2c_dev *i2c_dev, u32 val, unsigned int reg) | |
| { | |
| writel_relaxed(val, i2c_dev->base + reg); | |
| /* read back register to make sure that register writes completed */ | |
| if (reg != i2c_dev->hw->regs->tx_fifo) | |
| readl_relaxed(i2c_dev->base + reg); | |
| else if (IS_VI(i2c_dev)) | |
| readl_relaxed(i2c_dev->base + i2c_dev->hw->regs->int_status); | |
| } | |
| static u32 i2c_readl(struct tegra_i2c_dev *i2c_dev, unsigned int reg) | |
| { | |
| return readl_relaxed(i2c_dev->base + reg); | |
| } | |
| static void i2c_writesl(struct tegra_i2c_dev *i2c_dev, void *data, | |
| unsigned int reg, unsigned int len) | |
| { | |
| writesl(i2c_dev->base + reg, data, len); | |
| } | |
| static void i2c_writesl_vi(struct tegra_i2c_dev *i2c_dev, void *data, | |
| unsigned int reg, unsigned int len) | |
| { | |
| u32 *data32 = data; | |
| /* | |
| * VI I2C controller has known hardware bug where writes get stuck | |
| * when immediate multiple writes happen to TX_FIFO register. | |
| * Recommended software work around is to read I2C register after | |
| * each write to TX_FIFO register to flush out the data. | |
| */ | |
| while (len--) | |
| i2c_writel(i2c_dev, *data32++, reg); | |
| } | |
| static void i2c_readsl(struct tegra_i2c_dev *i2c_dev, void *data, | |
| unsigned int reg, unsigned int len) | |
| { | |
| readsl(i2c_dev->base + reg, data, len); | |
| } | |
| static bool tegra_i2c_mutex_acquired(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| unsigned int reg = i2c_dev->hw->regs->sw_mutex; | |
| u32 val, id; | |
| val = readl(i2c_dev->base + reg); | |
| id = FIELD_GET(I2C_SW_MUTEX_GRANT, val); | |
| return id == I2C_SW_MUTEX_ID_CCPLEX; | |
| } | |
| static bool tegra_i2c_mutex_trylock(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| unsigned int reg = i2c_dev->hw->regs->sw_mutex; | |
| u32 val, id; | |
| val = readl(i2c_dev->base + reg); | |
| id = FIELD_GET(I2C_SW_MUTEX_GRANT, val); | |
| if (id != 0 && id != I2C_SW_MUTEX_ID_CCPLEX) | |
| return false; | |
| val = FIELD_PREP(I2C_SW_MUTEX_REQUEST, I2C_SW_MUTEX_ID_CCPLEX); | |
| writel(val, i2c_dev->base + reg); | |
| return tegra_i2c_mutex_acquired(i2c_dev); | |
| } | |
| static int tegra_i2c_mutex_lock(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| bool locked; | |
| int ret; | |
| if (!i2c_dev->hw->has_mutex) | |
| return 0; | |
| if (i2c_dev->atomic_mode) | |
| ret = read_poll_timeout_atomic(tegra_i2c_mutex_trylock, locked, locked, | |
| USEC_PER_MSEC, I2C_SW_MUTEX_TIMEOUT_US, | |
| false, i2c_dev); | |
| else | |
| ret = read_poll_timeout(tegra_i2c_mutex_trylock, locked, locked, USEC_PER_MSEC, | |
| I2C_SW_MUTEX_TIMEOUT_US, false, i2c_dev); | |
| if (ret) | |
| dev_warn(i2c_dev->dev, "failed to acquire mutex\n"); | |
| return ret; | |
| } | |
| static void tegra_i2c_mutex_unlock(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| unsigned int reg = i2c_dev->hw->regs->sw_mutex; | |
| u32 val, id; | |
| if (!i2c_dev->hw->has_mutex) | |
| return; | |
| val = readl(i2c_dev->base + reg); | |
| id = FIELD_GET(I2C_SW_MUTEX_GRANT, val); | |
| if (WARN(id && id != I2C_SW_MUTEX_ID_CCPLEX, | |
| "unable to unlock mutex, mutex is owned by: %u\n", id)) | |
| return; | |
| writel(0, i2c_dev->base + reg); | |
| } | |
| static void tegra_i2c_mask_irq(struct tegra_i2c_dev *i2c_dev, u32 mask) | |
| { | |
| u32 int_mask; | |
| int_mask = i2c_readl(i2c_dev, i2c_dev->hw->regs->int_mask) & ~mask; | |
| i2c_writel(i2c_dev, int_mask, i2c_dev->hw->regs->int_mask); | |
| } | |
| static void tegra_i2c_unmask_irq(struct tegra_i2c_dev *i2c_dev, u32 mask) | |
| { | |
| u32 int_mask; | |
| int_mask = i2c_readl(i2c_dev, i2c_dev->hw->regs->int_mask) | mask; | |
| i2c_writel(i2c_dev, int_mask, i2c_dev->hw->regs->int_mask); | |
| } | |
| static void tegra_i2c_dma_complete(void *args) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = args; | |
| complete(&i2c_dev->dma_complete); | |
| } | |
| static int tegra_i2c_dma_submit(struct tegra_i2c_dev *i2c_dev, size_t len) | |
| { | |
| struct dma_async_tx_descriptor *dma_desc; | |
| enum dma_transfer_direction dir; | |
| dev_dbg(i2c_dev->dev, "starting DMA for length: %zu\n", len); | |
| reinit_completion(&i2c_dev->dma_complete); | |
| dir = i2c_dev->msg_read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV; | |
| dma_desc = dmaengine_prep_slave_single(i2c_dev->dma_chan, i2c_dev->dma_phys, | |
| len, dir, DMA_PREP_INTERRUPT | | |
| DMA_CTRL_ACK); | |
| if (!dma_desc) { | |
| dev_err(i2c_dev->dev, "failed to get %s DMA descriptor\n", | |
| i2c_dev->msg_read ? "RX" : "TX"); | |
| return -EINVAL; | |
| } | |
| dma_desc->callback = tegra_i2c_dma_complete; | |
| dma_desc->callback_param = i2c_dev; | |
| dmaengine_submit(dma_desc); | |
| dma_async_issue_pending(i2c_dev->dma_chan); | |
| return 0; | |
| } | |
| static void tegra_i2c_release_dma(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| if (i2c_dev->dma_buf) { | |
| dma_free_coherent(i2c_dev->dma_dev, i2c_dev->dma_buf_size, | |
| i2c_dev->dma_buf, i2c_dev->dma_phys); | |
| i2c_dev->dma_buf = NULL; | |
| } | |
| if (i2c_dev->dma_chan) { | |
| dma_release_channel(i2c_dev->dma_chan); | |
| i2c_dev->dma_chan = NULL; | |
| } | |
| } | |
| static int tegra_i2c_init_dma(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| dma_addr_t dma_phys; | |
| u32 *dma_buf; | |
| int err; | |
| if (IS_VI(i2c_dev)) | |
| return 0; | |
| if (!of_property_present(i2c_dev->dev->of_node, "dmas")) { | |
| dev_dbg(i2c_dev->dev, "DMA not available, falling back to PIO\n"); | |
| return 0; | |
| } | |
| if (i2c_dev->hw->has_apb_dma) { | |
| if (!IS_ENABLED(CONFIG_TEGRA20_APB_DMA)) { | |
| dev_dbg(i2c_dev->dev, "APB DMA support not enabled\n"); | |
| return 0; | |
| } | |
| } else if (!IS_ENABLED(CONFIG_TEGRA186_GPC_DMA)) { | |
| dev_dbg(i2c_dev->dev, "GPC DMA support not enabled\n"); | |
| return 0; | |
| } | |
| /* | |
| * The same channel will be used for both RX and TX. | |
| * Keeping the name as "tx" for backward compatibility | |
| * with existing devicetrees. | |
| */ | |
| i2c_dev->dma_chan = dma_request_chan(i2c_dev->dev, "tx"); | |
| if (IS_ERR(i2c_dev->dma_chan)) { | |
| err = PTR_ERR(i2c_dev->dma_chan); | |
| i2c_dev->dma_chan = NULL; | |
| goto err_out; | |
| } | |
| i2c_dev->dma_dev = dmaengine_get_dma_device(i2c_dev->dma_chan); | |
| i2c_dev->dma_buf_size = i2c_dev->hw->quirks->max_write_len + | |
| I2C_PACKET_HEADER_SIZE; | |
| dma_buf = dma_alloc_coherent(i2c_dev->dma_dev, i2c_dev->dma_buf_size, | |
| &dma_phys, GFP_KERNEL | __GFP_NOWARN); | |
| if (!dma_buf) { | |
| err = dev_err_probe(i2c_dev->dev, -ENOMEM, | |
| "failed to allocate DMA buffer\n"); | |
| goto err_out; | |
| } | |
| i2c_dev->dma_buf = dma_buf; | |
| i2c_dev->dma_phys = dma_phys; | |
| return 0; | |
| err_out: | |
| tegra_i2c_release_dma(i2c_dev); | |
| if (err != -EPROBE_DEFER) { | |
| dev_err(i2c_dev->dev, "cannot use DMA, falling back to PIO\n"); | |
| return 0; | |
| } | |
| return err; | |
| } | |
| /* | |
| * One of the Tegra I2C blocks is inside the DVC (Digital Voltage Controller) | |
| * block. This block is identical to the rest of the I2C blocks, except that | |
| * it only supports master mode, it has registers moved around, and it needs | |
| * some extra init to get it into I2C mode. The register moves are handled | |
| * by i2c_readl() and i2c_writel(). | |
| */ | |
| static void tegra_dvc_init(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| u32 val; | |
| val = dvc_readl(i2c_dev, DVC_CTRL_REG3); | |
| val |= DVC_CTRL_REG3_SW_PROG; | |
| val |= DVC_CTRL_REG3_I2C_DONE_INTR_EN; | |
| dvc_writel(i2c_dev, val, DVC_CTRL_REG3); | |
| val = dvc_readl(i2c_dev, DVC_CTRL_REG1); | |
| val |= DVC_CTRL_REG1_INTR_EN; | |
| dvc_writel(i2c_dev, val, DVC_CTRL_REG1); | |
| } | |
| static void tegra_i2c_vi_init(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| u32 value; | |
| value = FIELD_PREP(I2C_INTERFACE_TIMING_THIGH, 2) | | |
| FIELD_PREP(I2C_INTERFACE_TIMING_TLOW, 4); | |
| i2c_writel(i2c_dev, value, i2c_dev->hw->regs->interface_timing_0); | |
| value = FIELD_PREP(I2C_INTERFACE_TIMING_TBUF, 4) | | |
| FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STO, 7) | | |
| FIELD_PREP(I2C_INTERFACE_TIMING_THD_STA, 4) | | |
| FIELD_PREP(I2C_INTERFACE_TIMING_TSU_STA, 4); | |
| i2c_writel(i2c_dev, value, i2c_dev->hw->regs->interface_timing_1); | |
| value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_THIGH, 3) | | |
| FIELD_PREP(I2C_HS_INTERFACE_TIMING_TLOW, 8); | |
| i2c_writel(i2c_dev, value, i2c_dev->hw->regs->hs_interface_timing_0); | |
| value = FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STO, 11) | | |
| FIELD_PREP(I2C_HS_INTERFACE_TIMING_THD_STA, 11) | | |
| FIELD_PREP(I2C_HS_INTERFACE_TIMING_TSU_STA, 11); | |
| i2c_writel(i2c_dev, value, i2c_dev->hw->regs->hs_interface_timing_1); | |
| value = FIELD_PREP(I2C_BC_SCLK_THRESHOLD, 9) | I2C_BC_STOP_COND; | |
| i2c_writel(i2c_dev, value, i2c_dev->hw->regs->bus_clear_cnfg); | |
| i2c_writel(i2c_dev, 0x0, i2c_dev->hw->regs->tlow_sext); | |
| } | |
| static int tegra_i2c_poll_register(struct tegra_i2c_dev *i2c_dev, | |
| u32 reg, u32 mask, u32 delay_us, | |
| u32 timeout_us) | |
| { | |
| void __iomem *addr = i2c_dev->base + reg; | |
| u32 val; | |
| if (!i2c_dev->atomic_mode) | |
| return readl_relaxed_poll_timeout(addr, val, !(val & mask), | |
| delay_us, timeout_us); | |
| return readl_relaxed_poll_timeout_atomic(addr, val, !(val & mask), | |
| delay_us, timeout_us); | |
| } | |
| static int tegra_i2c_flush_fifos(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| u32 mask, val, offset; | |
| int err; | |
| if (i2c_dev->hw->has_mst_fifo) { | |
| mask = I2C_MST_FIFO_CONTROL_TX_FLUSH | | |
| I2C_MST_FIFO_CONTROL_RX_FLUSH; | |
| offset = i2c_dev->hw->regs->mst_fifo_control; | |
| } else { | |
| mask = I2C_FIFO_CONTROL_TX_FLUSH | | |
| I2C_FIFO_CONTROL_RX_FLUSH; | |
| offset = i2c_dev->hw->regs->fifo_control; | |
| } | |
| val = i2c_readl(i2c_dev, offset); | |
| val |= mask; | |
| i2c_writel(i2c_dev, val, offset); | |
| err = tegra_i2c_poll_register(i2c_dev, offset, mask, 1000, 1000000); | |
| if (err) { | |
| dev_err(i2c_dev->dev, "failed to flush FIFO\n"); | |
| return err; | |
| } | |
| return 0; | |
| } | |
| static int tegra_i2c_wait_for_config_load(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| int err; | |
| if (!i2c_dev->hw->has_config_load_reg) | |
| return 0; | |
| i2c_writel(i2c_dev, I2C_MSTR_CONFIG_LOAD, i2c_dev->hw->regs->config_load); | |
| err = tegra_i2c_poll_register(i2c_dev, i2c_dev->hw->regs->config_load, 0xffffffff, | |
| 1000, I2C_CONFIG_LOAD_TIMEOUT); | |
| if (err) { | |
| dev_err(i2c_dev->dev, "failed to load config\n"); | |
| return err; | |
| } | |
| return 0; | |
| } | |
| static int tegra_i2c_master_reset(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| if (!i2c_dev->hw->has_mst_reset) | |
| return -EOPNOTSUPP; | |
| /* | |
| * Writing 1 to I2C_MASTER_RESET_CNTRL will reset all internal state of | |
| * Master logic including FIFOs. Clear this bit to 0 for normal operation. | |
| * SW needs to wait for 2us after assertion and de-assertion of this soft | |
| * reset. | |
| */ | |
| i2c_writel(i2c_dev, 0x1, i2c_dev->hw->regs->master_reset_cntrl); | |
| fsleep(2); | |
| i2c_writel(i2c_dev, 0x0, i2c_dev->hw->regs->master_reset_cntrl); | |
| fsleep(2); | |
| return 0; | |
| } | |
| static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| u32 val, clk_divisor, clk_multiplier, tsu_thd, tlow, thigh, non_hs_mode; | |
| u32 max_bus_freq_hz; | |
| struct i2c_timings *t = &i2c_dev->timings; | |
| int err; | |
| /* | |
| * Reset the controller before initializing it. | |
| * In case if device_reset() returns -ENOENT, i.e. when the reset is | |
| * not available, the internal software reset will be used if it is | |
| * supported by the controller. | |
| */ | |
| err = device_reset(i2c_dev->dev); | |
| if (err == -ENOENT) | |
| err = tegra_i2c_master_reset(i2c_dev); | |
| /* | |
| * The reset shouldn't ever fail in practice. The failure will be a | |
| * sign of a severe problem that needs to be resolved. Still we don't | |
| * want to fail the initialization completely because this may break | |
| * kernel boot up since voltage regulators use I2C. Hence, we will | |
| * emit a noisy warning on error, which won't stay unnoticed and | |
| * won't hose machine entirely. | |
| */ | |
| WARN_ON_ONCE(err); | |
| if (IS_DVC(i2c_dev)) | |
| tegra_dvc_init(i2c_dev); | |
| val = I2C_CNFG_NEW_MASTER_FSM | I2C_CNFG_PACKET_MODE_EN | | |
| FIELD_PREP(I2C_CNFG_DEBOUNCE_CNT, 2); | |
| if (i2c_dev->hw->has_multi_master_mode) | |
| val |= I2C_CNFG_MULTI_MASTER_MODE; | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->cnfg); | |
| i2c_writel(i2c_dev, 0, i2c_dev->hw->regs->int_mask); | |
| if (IS_VI(i2c_dev)) | |
| tegra_i2c_vi_init(i2c_dev); | |
| /* Disable fairness arbitration if not an MCTP controller */ | |
| if (i2c_dev->hw->has_fairarb_reg && !i2c_dev->is_mctp) | |
| i2c_writel(i2c_dev, 0, i2c_dev->hw->regs->fairness_arb); | |
| if (i2c_dev->hw->enable_hs_mode_support) | |
| max_bus_freq_hz = I2C_MAX_HIGH_SPEED_MODE_FREQ; | |
| else | |
| max_bus_freq_hz = I2C_MAX_FAST_MODE_PLUS_FREQ; | |
| if (WARN_ON(t->bus_freq_hz > max_bus_freq_hz)) | |
| t->bus_freq_hz = max_bus_freq_hz; | |
| if (t->bus_freq_hz <= I2C_MAX_STANDARD_MODE_FREQ) { | |
| tlow = i2c_dev->hw->tlow_std_mode; | |
| thigh = i2c_dev->hw->thigh_std_mode; | |
| tsu_thd = i2c_dev->hw->setup_hold_time_std_mode; | |
| non_hs_mode = i2c_dev->hw->clk_divisor_std_mode; | |
| } else if (t->bus_freq_hz <= I2C_MAX_FAST_MODE_FREQ) { | |
| tlow = i2c_dev->hw->tlow_fast_mode; | |
| thigh = i2c_dev->hw->thigh_fast_mode; | |
| tsu_thd = i2c_dev->hw->setup_hold_time_fast_mode; | |
| non_hs_mode = i2c_dev->hw->clk_divisor_fast_mode; | |
| } else if (t->bus_freq_hz <= I2C_MAX_FAST_MODE_PLUS_FREQ) { | |
| tlow = i2c_dev->hw->tlow_fastplus_mode; | |
| thigh = i2c_dev->hw->thigh_fastplus_mode; | |
| tsu_thd = i2c_dev->hw->setup_hold_time_fastplus_mode; | |
| non_hs_mode = i2c_dev->hw->clk_divisor_fast_plus_mode; | |
| } else { | |
| /* | |
| * When using HS mode, i.e. when the bus frequency is greater than fast plus mode, | |
| * the non-hs timing registers will be used for sending the master code byte for | |
| * transition to HS mode. Configure the non-hs timing registers for Fast Mode to | |
| * send the master code byte at 400kHz. | |
| */ | |
| tlow = i2c_dev->hw->tlow_fast_mode; | |
| thigh = i2c_dev->hw->thigh_fast_mode; | |
| tsu_thd = i2c_dev->hw->setup_hold_time_fast_mode; | |
| non_hs_mode = i2c_dev->hw->clk_divisor_fast_mode; | |
| } | |
| /* make sure clock divisor programmed correctly */ | |
| clk_divisor = FIELD_PREP(I2C_CLK_DIVISOR_HSMODE, | |
| i2c_dev->hw->clk_divisor_hs_mode) | | |
| FIELD_PREP(I2C_CLK_DIVISOR_STD_FAST_MODE, non_hs_mode); | |
| i2c_writel(i2c_dev, clk_divisor, i2c_dev->hw->regs->clk_divisor); | |
| if (i2c_dev->hw->has_interface_timing_reg) { | |
| val = FIELD_PREP(I2C_INTERFACE_TIMING_THIGH, thigh) | | |
| FIELD_PREP(I2C_INTERFACE_TIMING_TLOW, tlow); | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->interface_timing_0); | |
| } | |
| /* | |
| * Configure setup and hold times only when tsu_thd is non-zero. | |
| * Otherwise, preserve the chip default values. | |
| */ | |
| if (i2c_dev->hw->has_interface_timing_reg && tsu_thd) | |
| i2c_writel(i2c_dev, tsu_thd, i2c_dev->hw->regs->interface_timing_1); | |
| /* Write HS mode registers. These will get used only for HS mode*/ | |
| if (i2c_dev->hw->enable_hs_mode_support) { | |
| tlow = i2c_dev->hw->tlow_hs_mode; | |
| thigh = i2c_dev->hw->thigh_hs_mode; | |
| tsu_thd = i2c_dev->hw->setup_hold_time_hs_mode; | |
| val = FIELD_PREP(I2C_HS_INTERFACE_TIMING_THIGH, thigh) | | |
| FIELD_PREP(I2C_HS_INTERFACE_TIMING_TLOW, tlow); | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->hs_interface_timing_0); | |
| i2c_writel(i2c_dev, tsu_thd, i2c_dev->hw->regs->hs_interface_timing_1); | |
| } | |
| clk_multiplier = (tlow + thigh + 2) * (non_hs_mode + 1); | |
| err = clk_set_rate(i2c_dev->div_clk, | |
| t->bus_freq_hz * clk_multiplier); | |
| if (err) { | |
| dev_err(i2c_dev->dev, "failed to set div-clk rate: %d\n", err); | |
| return err; | |
| } | |
| if (!IS_DVC(i2c_dev) && !IS_VI(i2c_dev)) { | |
| u32 sl_cfg = i2c_readl(i2c_dev, i2c_dev->hw->regs->sl_cnfg); | |
| sl_cfg |= I2C_SL_CNFG_NACK | I2C_SL_CNFG_NEWSL; | |
| i2c_writel(i2c_dev, sl_cfg, i2c_dev->hw->regs->sl_cnfg); | |
| i2c_writel(i2c_dev, 0xfc, i2c_dev->hw->regs->sl_addr1); | |
| i2c_writel(i2c_dev, 0x00, i2c_dev->hw->regs->sl_addr2); | |
| } | |
| err = tegra_i2c_flush_fifos(i2c_dev); | |
| if (err) | |
| return err; | |
| if (i2c_dev->multimaster_mode && i2c_dev->hw->has_slcg_override_reg) | |
| i2c_writel(i2c_dev, I2C_MST_CORE_CLKEN_OVR, i2c_dev->hw->regs->clken_override); | |
| err = tegra_i2c_wait_for_config_load(i2c_dev); | |
| if (err) | |
| return err; | |
| return 0; | |
| } | |
| static int tegra_i2c_disable_packet_mode(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| u32 cnfg; | |
| /* | |
| * NACK interrupt is generated before the I2C controller generates | |
| * the STOP condition on the bus. So, wait for 2 clock periods | |
| * before disabling the controller so that the STOP condition has | |
| * been delivered properly. | |
| */ | |
| udelay(DIV_ROUND_UP(2 * 1000000, i2c_dev->timings.bus_freq_hz)); | |
| cnfg = i2c_readl(i2c_dev, i2c_dev->hw->regs->cnfg); | |
| if (cnfg & I2C_CNFG_PACKET_MODE_EN) | |
| i2c_writel(i2c_dev, cnfg & ~I2C_CNFG_PACKET_MODE_EN, i2c_dev->hw->regs->cnfg); | |
| return tegra_i2c_wait_for_config_load(i2c_dev); | |
| } | |
| static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| size_t buf_remaining = i2c_dev->msg_buf_remaining; | |
| unsigned int words_to_transfer, rx_fifo_avail; | |
| u8 *buf = i2c_dev->msg_buf; | |
| u32 val; | |
| /* | |
| * Catch overflow due to message fully sent before the check for | |
| * RX FIFO availability. | |
| */ | |
| if (WARN_ON_ONCE(!(i2c_dev->msg_buf_remaining))) | |
| return -EINVAL; | |
| if (i2c_dev->hw->has_mst_fifo) { | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->mst_fifo_status); | |
| rx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_RX, val); | |
| } else { | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->fifo_status); | |
| rx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_RX, val); | |
| } | |
| /* round down to exclude partial word at the end of buffer */ | |
| words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD; | |
| if (words_to_transfer > rx_fifo_avail) | |
| words_to_transfer = rx_fifo_avail; | |
| i2c_readsl(i2c_dev, buf, i2c_dev->hw->regs->rx_fifo, words_to_transfer); | |
| buf += words_to_transfer * BYTES_PER_FIFO_WORD; | |
| buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD; | |
| rx_fifo_avail -= words_to_transfer; | |
| /* | |
| * If there is a partial word at the end of buffer, handle it | |
| * manually to prevent overwriting past the end of buffer. | |
| */ | |
| if (rx_fifo_avail > 0 && buf_remaining > 0) { | |
| /* | |
| * buf_remaining > 3 check not needed as rx_fifo_avail == 0 | |
| * when (words_to_transfer was > rx_fifo_avail) earlier | |
| * in this function. | |
| */ | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->rx_fifo); | |
| val = cpu_to_le32(val); | |
| memcpy(buf, &val, buf_remaining); | |
| buf_remaining = 0; | |
| rx_fifo_avail--; | |
| } | |
| /* RX FIFO must be drained, otherwise it's an Overflow case. */ | |
| if (WARN_ON_ONCE(rx_fifo_avail)) | |
| return -EINVAL; | |
| i2c_dev->msg_buf_remaining = buf_remaining; | |
| i2c_dev->msg_buf = buf; | |
| return 0; | |
| } | |
| static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| size_t buf_remaining = i2c_dev->msg_buf_remaining; | |
| unsigned int words_to_transfer, tx_fifo_avail; | |
| u8 *buf = i2c_dev->msg_buf; | |
| u32 val; | |
| if (i2c_dev->hw->has_mst_fifo) { | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->mst_fifo_status); | |
| tx_fifo_avail = FIELD_GET(I2C_MST_FIFO_STATUS_TX, val); | |
| } else { | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->fifo_status); | |
| tx_fifo_avail = FIELD_GET(I2C_FIFO_STATUS_TX, val); | |
| } | |
| /* round down to exclude partial word at the end of buffer */ | |
| words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD; | |
| /* | |
| * This hunk pushes 4 bytes at a time into the TX FIFO. | |
| * | |
| * It's very common to have < 4 bytes, hence there is no word | |
| * to push if we have less than 4 bytes to transfer. | |
| */ | |
| if (words_to_transfer) { | |
| if (words_to_transfer > tx_fifo_avail) | |
| words_to_transfer = tx_fifo_avail; | |
| /* | |
| * Update state before writing to FIFO. Note that this may | |
| * cause us to finish writing all bytes (AKA buf_remaining | |
| * goes to 0), hence we have a potential for an interrupt | |
| * (PACKET_XFER_COMPLETE is not maskable), but GIC interrupt | |
| * is disabled at this point. | |
| */ | |
| buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD; | |
| tx_fifo_avail -= words_to_transfer; | |
| i2c_dev->msg_buf_remaining = buf_remaining; | |
| i2c_dev->msg_buf = buf + words_to_transfer * BYTES_PER_FIFO_WORD; | |
| if (IS_VI(i2c_dev)) | |
| i2c_writesl_vi(i2c_dev, buf, i2c_dev->hw->regs->tx_fifo, words_to_transfer); | |
| else | |
| i2c_writesl(i2c_dev, buf, i2c_dev->hw->regs->tx_fifo, words_to_transfer); | |
| buf += words_to_transfer * BYTES_PER_FIFO_WORD; | |
| } | |
| /* | |
| * If there is a partial word at the end of buffer, handle it manually | |
| * to prevent reading past the end of buffer, which could cross a page | |
| * boundary and fault. | |
| */ | |
| if (tx_fifo_avail > 0 && buf_remaining > 0) { | |
| /* | |
| * buf_remaining > 3 check not needed as tx_fifo_avail == 0 | |
| * when (words_to_transfer was > tx_fifo_avail) earlier | |
| * in this function for non-zero words_to_transfer. | |
| */ | |
| memcpy(&val, buf, buf_remaining); | |
| val = le32_to_cpu(val); | |
| i2c_dev->msg_buf_remaining = 0; | |
| i2c_dev->msg_buf = NULL; | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->tx_fifo); | |
| } | |
| return 0; | |
| } | |
| static irqreturn_t tegra_i2c_isr(int irq, void *dev_id) | |
| { | |
| const u32 status_err = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST; | |
| struct tegra_i2c_dev *i2c_dev = dev_id; | |
| u32 status; | |
| status = i2c_readl(i2c_dev, i2c_dev->hw->regs->int_status); | |
| if (status == 0) { | |
| dev_warn(i2c_dev->dev, "IRQ status 0 %08x %08x %08x\n", | |
| i2c_readl(i2c_dev, i2c_dev->hw->regs->packet_transfer_status), | |
| i2c_readl(i2c_dev, i2c_dev->hw->regs->status), | |
| i2c_readl(i2c_dev, i2c_dev->hw->regs->cnfg)); | |
| i2c_dev->msg_err |= I2C_ERR_UNKNOWN_INTERRUPT; | |
| goto err; | |
| } | |
| if (status & status_err) { | |
| tegra_i2c_disable_packet_mode(i2c_dev); | |
| if (status & I2C_INT_NO_ACK) | |
| i2c_dev->msg_err |= I2C_ERR_NO_ACK; | |
| if (status & I2C_INT_ARBITRATION_LOST) | |
| i2c_dev->msg_err |= I2C_ERR_ARBITRATION_LOST; | |
| goto err; | |
| } | |
| /* | |
| * I2C transfer is terminated during the bus clear, so skip | |
| * processing the other interrupts. | |
| */ | |
| if (i2c_dev->hw->supports_bus_clear && (status & I2C_INT_BUS_CLR_DONE)) | |
| goto err; | |
| if (!i2c_dev->dma_mode) { | |
| if (i2c_dev->msg_read && (status & I2C_INT_RX_FIFO_DATA_REQ)) { | |
| if (tegra_i2c_empty_rx_fifo(i2c_dev)) { | |
| /* | |
| * Overflow error condition: message fully sent, | |
| * with no XFER_COMPLETE interrupt but hardware | |
| * asks to transfer more. | |
| */ | |
| i2c_dev->msg_err |= I2C_ERR_RX_BUFFER_OVERFLOW; | |
| goto err; | |
| } | |
| } | |
| if (!i2c_dev->msg_read && (status & I2C_INT_TX_FIFO_DATA_REQ)) { | |
| if (i2c_dev->msg_buf_remaining) | |
| tegra_i2c_fill_tx_fifo(i2c_dev); | |
| else | |
| tegra_i2c_mask_irq(i2c_dev, | |
| I2C_INT_TX_FIFO_DATA_REQ); | |
| } | |
| } | |
| i2c_writel(i2c_dev, status, i2c_dev->hw->regs->int_status); | |
| if (IS_DVC(i2c_dev)) | |
| dvc_writel(i2c_dev, DVC_STATUS_I2C_DONE_INTR, DVC_STATUS); | |
| /* | |
| * During message read XFER_COMPLETE interrupt is triggered prior to | |
| * DMA completion and during message write XFER_COMPLETE interrupt is | |
| * triggered after DMA completion. | |
| * | |
| * PACKETS_XFER_COMPLETE indicates completion of all bytes of transfer, | |
| * so forcing msg_buf_remaining to 0 in DMA mode. | |
| */ | |
| if (status & I2C_INT_PACKET_XFER_COMPLETE) { | |
| if (i2c_dev->dma_mode) | |
| i2c_dev->msg_buf_remaining = 0; | |
| /* | |
| * Underflow error condition: XFER_COMPLETE before message | |
| * fully sent. | |
| */ | |
| if (WARN_ON_ONCE(i2c_dev->msg_buf_remaining)) { | |
| i2c_dev->msg_err |= I2C_ERR_UNKNOWN_INTERRUPT; | |
| goto err; | |
| } | |
| complete(&i2c_dev->msg_complete); | |
| } | |
| goto done; | |
| err: | |
| /* mask all interrupts on error */ | |
| tegra_i2c_mask_irq(i2c_dev, | |
| I2C_INT_NO_ACK | | |
| I2C_INT_ARBITRATION_LOST | | |
| I2C_INT_PACKET_XFER_COMPLETE | | |
| I2C_INT_TX_FIFO_DATA_REQ | | |
| I2C_INT_RX_FIFO_DATA_REQ); | |
| if (i2c_dev->hw->supports_bus_clear) | |
| tegra_i2c_mask_irq(i2c_dev, I2C_INT_BUS_CLR_DONE); | |
| i2c_writel(i2c_dev, status, i2c_dev->hw->regs->int_status); | |
| if (IS_DVC(i2c_dev)) | |
| dvc_writel(i2c_dev, DVC_STATUS_I2C_DONE_INTR, DVC_STATUS); | |
| if (i2c_dev->dma_mode) { | |
| dmaengine_terminate_async(i2c_dev->dma_chan); | |
| complete(&i2c_dev->dma_complete); | |
| } | |
| complete(&i2c_dev->msg_complete); | |
| done: | |
| return IRQ_HANDLED; | |
| } | |
| static void tegra_i2c_config_fifo_trig(struct tegra_i2c_dev *i2c_dev, | |
| size_t len) | |
| { | |
| struct dma_slave_config slv_config = {0}; | |
| u32 val, reg, dma_burst, reg_offset; | |
| int err; | |
| if (i2c_dev->hw->has_mst_fifo) | |
| reg = i2c_dev->hw->regs->mst_fifo_control; | |
| else | |
| reg = i2c_dev->hw->regs->fifo_control; | |
| if (i2c_dev->dma_mode) { | |
| if (len & 0xF) | |
| dma_burst = 1; | |
| else if (len & 0x10) | |
| dma_burst = 4; | |
| else | |
| dma_burst = 8; | |
| if (i2c_dev->msg_read) { | |
| reg_offset = i2c_dev->hw->regs->rx_fifo; | |
| slv_config.src_addr = i2c_dev->base_phys + reg_offset; | |
| slv_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; | |
| slv_config.src_maxburst = dma_burst; | |
| if (i2c_dev->hw->has_mst_fifo) | |
| val = I2C_MST_FIFO_CONTROL_RX_TRIG(dma_burst); | |
| else | |
| val = I2C_FIFO_CONTROL_RX_TRIG(dma_burst); | |
| } else { | |
| reg_offset = i2c_dev->hw->regs->tx_fifo; | |
| slv_config.dst_addr = i2c_dev->base_phys + reg_offset; | |
| slv_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; | |
| slv_config.dst_maxburst = dma_burst; | |
| if (i2c_dev->hw->has_mst_fifo) | |
| val = I2C_MST_FIFO_CONTROL_TX_TRIG(dma_burst); | |
| else | |
| val = I2C_FIFO_CONTROL_TX_TRIG(dma_burst); | |
| } | |
| slv_config.device_fc = true; | |
| err = dmaengine_slave_config(i2c_dev->dma_chan, &slv_config); | |
| if (err) { | |
| dev_err(i2c_dev->dev, "DMA config failed: %d\n", err); | |
| dev_err(i2c_dev->dev, "falling back to PIO\n"); | |
| tegra_i2c_release_dma(i2c_dev); | |
| i2c_dev->dma_mode = false; | |
| } else { | |
| goto out; | |
| } | |
| } | |
| if (i2c_dev->hw->has_mst_fifo) | |
| val = I2C_MST_FIFO_CONTROL_TX_TRIG(8) | | |
| I2C_MST_FIFO_CONTROL_RX_TRIG(1); | |
| else | |
| val = I2C_FIFO_CONTROL_TX_TRIG(8) | | |
| I2C_FIFO_CONTROL_RX_TRIG(1); | |
| out: | |
| i2c_writel(i2c_dev, val, reg); | |
| } | |
| static unsigned long tegra_i2c_poll_completion(struct tegra_i2c_dev *i2c_dev, | |
| struct completion *complete, | |
| unsigned int timeout_ms) | |
| { | |
| ktime_t ktime = ktime_get(); | |
| ktime_t ktimeout = ktime_add_ms(ktime, timeout_ms); | |
| do { | |
| u32 status = i2c_readl(i2c_dev, i2c_dev->hw->regs->int_status); | |
| if (status) | |
| tegra_i2c_isr(i2c_dev->irq, i2c_dev); | |
| if (completion_done(complete)) { | |
| s64 delta = ktime_ms_delta(ktimeout, ktime); | |
| return msecs_to_jiffies(delta) ?: 1; | |
| } | |
| ktime = ktime_get(); | |
| } while (ktime_before(ktime, ktimeout)); | |
| return 0; | |
| } | |
| static unsigned long tegra_i2c_wait_completion(struct tegra_i2c_dev *i2c_dev, | |
| struct completion *complete, | |
| unsigned int timeout_ms) | |
| { | |
| unsigned long ret; | |
| if (i2c_dev->atomic_mode) { | |
| ret = tegra_i2c_poll_completion(i2c_dev, complete, timeout_ms); | |
| } else { | |
| enable_irq(i2c_dev->irq); | |
| ret = wait_for_completion_timeout(complete, | |
| msecs_to_jiffies(timeout_ms)); | |
| disable_irq(i2c_dev->irq); | |
| /* | |
| * Under some rare circumstances (like running KASAN + | |
| * NFS root) CPU, which handles interrupt, may stuck in | |
| * uninterruptible state for a significant time. In this | |
| * case we will get timeout if I2C transfer is running on | |
| * a sibling CPU, despite of IRQ being raised. | |
| * | |
| * In order to handle this rare condition, the IRQ status | |
| * needs to be checked after timeout. | |
| */ | |
| if (ret == 0) | |
| ret = tegra_i2c_poll_completion(i2c_dev, complete, 0); | |
| } | |
| return ret; | |
| } | |
| static int tegra_i2c_issue_bus_clear(struct i2c_adapter *adap) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | |
| u32 val, time_left; | |
| int err; | |
| reinit_completion(&i2c_dev->msg_complete); | |
| val = FIELD_PREP(I2C_BC_SCLK_THRESHOLD, 9) | I2C_BC_STOP_COND | | |
| I2C_BC_TERMINATE; | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->bus_clear_cnfg); | |
| err = tegra_i2c_wait_for_config_load(i2c_dev); | |
| if (err) | |
| return err; | |
| val |= I2C_BC_ENABLE; | |
| i2c_writel(i2c_dev, val, i2c_dev->hw->regs->bus_clear_cnfg); | |
| tegra_i2c_unmask_irq(i2c_dev, I2C_INT_BUS_CLR_DONE); | |
| time_left = tegra_i2c_wait_completion(i2c_dev, &i2c_dev->msg_complete, 50); | |
| tegra_i2c_mask_irq(i2c_dev, I2C_INT_BUS_CLR_DONE); | |
| if (time_left == 0) { | |
| dev_err(i2c_dev->dev, "failed to clear bus\n"); | |
| return -ETIMEDOUT; | |
| } | |
| val = i2c_readl(i2c_dev, i2c_dev->hw->regs->bus_clear_status); | |
| if (!(val & I2C_BC_STATUS)) { | |
| dev_err(i2c_dev->dev, "un-recovered arbitration lost\n"); | |
| return -EIO; | |
| } | |
| return -EAGAIN; | |
| } | |
| static void tegra_i2c_push_packet_header(struct tegra_i2c_dev *i2c_dev, | |
| struct i2c_msg *msg, | |
| enum msg_end_type end_state) | |
| { | |
| u32 *dma_buf = i2c_dev->dma_buf; | |
| u32 packet_header; | |
| packet_header = FIELD_PREP(PACKET_HEADER0_HEADER_SIZE, 0) | | |
| FIELD_PREP(PACKET_HEADER0_PROTOCOL, | |
| PACKET_HEADER0_PROTOCOL_I2C) | | |
| FIELD_PREP(PACKET_HEADER0_CONT_ID, i2c_dev->cont_id) | | |
| FIELD_PREP(PACKET_HEADER0_PACKET_ID, 1); | |
| if (i2c_dev->dma_mode && !i2c_dev->msg_read) | |
| *dma_buf++ = packet_header; | |
| else | |
| i2c_writel(i2c_dev, packet_header, i2c_dev->hw->regs->tx_fifo); | |
| packet_header = i2c_dev->msg_len - 1; | |
| if (i2c_dev->dma_mode && !i2c_dev->msg_read) | |
| *dma_buf++ = packet_header; | |
| else | |
| i2c_writel(i2c_dev, packet_header, i2c_dev->hw->regs->tx_fifo); | |
| packet_header = I2C_HEADER_IE_ENABLE; | |
| if (end_state == MSG_END_CONTINUE) | |
| packet_header |= I2C_HEADER_CONTINUE_XFER; | |
| else if (end_state == MSG_END_REPEAT_START) | |
| packet_header |= I2C_HEADER_REPEAT_START; | |
| if (msg->flags & I2C_M_TEN) { | |
| packet_header |= msg->addr; | |
| packet_header |= I2C_HEADER_10BIT_ADDR; | |
| } else { | |
| packet_header |= msg->addr << I2C_HEADER_SLAVE_ADDR_SHIFT; | |
| } | |
| if (msg->flags & I2C_M_IGNORE_NAK) | |
| packet_header |= I2C_HEADER_CONT_ON_NAK; | |
| if (msg->flags & I2C_M_RD) | |
| packet_header |= I2C_HEADER_READ; | |
| if (i2c_dev->timings.bus_freq_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) | |
| packet_header |= I2C_HEADER_HS_MODE; | |
| if (i2c_dev->dma_mode && !i2c_dev->msg_read) | |
| *dma_buf++ = packet_header; | |
| else | |
| i2c_writel(i2c_dev, packet_header, i2c_dev->hw->regs->tx_fifo); | |
| } | |
| static int tegra_i2c_error_recover(struct tegra_i2c_dev *i2c_dev, | |
| struct i2c_msg *msg) | |
| { | |
| if (i2c_dev->msg_err == I2C_ERR_NONE) | |
| return 0; | |
| tegra_i2c_init(i2c_dev); | |
| /* start recovery upon arbitration loss in single master mode */ | |
| if (i2c_dev->msg_err == I2C_ERR_ARBITRATION_LOST) { | |
| if (!i2c_dev->multimaster_mode) | |
| return i2c_recover_bus(&i2c_dev->adapter); | |
| return -EAGAIN; | |
| } | |
| if (i2c_dev->msg_err == I2C_ERR_NO_ACK) { | |
| if (msg->flags & I2C_M_IGNORE_NAK) | |
| return 0; | |
| return -EREMOTEIO; | |
| } | |
| return -EIO; | |
| } | |
| static int tegra_i2c_xfer_msg(struct tegra_i2c_dev *i2c_dev, | |
| struct i2c_msg *msg, | |
| enum msg_end_type end_state) | |
| { | |
| unsigned long time_left, xfer_time = 100; | |
| size_t xfer_size; | |
| u32 int_mask; | |
| int err; | |
| err = tegra_i2c_flush_fifos(i2c_dev); | |
| if (err) | |
| return err; | |
| i2c_dev->msg_buf = msg->buf; | |
| i2c_dev->msg_len = msg->len; | |
| i2c_dev->msg_err = I2C_ERR_NONE; | |
| i2c_dev->msg_read = !!(msg->flags & I2C_M_RD); | |
| reinit_completion(&i2c_dev->msg_complete); | |
| /* | |
| * For SMBUS block read command, read only 1 byte in the first transfer. | |
| * Adjust that 1 byte for the next transfer in the msg buffer and msg | |
| * length. | |
| */ | |
| if (msg->flags & I2C_M_RECV_LEN) { | |
| if (end_state == MSG_END_CONTINUE) { | |
| i2c_dev->msg_len = 1; | |
| } else { | |
| i2c_dev->msg_buf += 1; | |
| i2c_dev->msg_len -= 1; | |
| } | |
| } | |
| i2c_dev->msg_buf_remaining = i2c_dev->msg_len; | |
| if (i2c_dev->msg_read) | |
| xfer_size = i2c_dev->msg_len; | |
| else | |
| xfer_size = i2c_dev->msg_len + I2C_PACKET_HEADER_SIZE; | |
| xfer_size = ALIGN(xfer_size, BYTES_PER_FIFO_WORD); | |
| i2c_dev->dma_mode = xfer_size > I2C_PIO_MODE_PREFERRED_LEN && | |
| i2c_dev->dma_buf && !i2c_dev->atomic_mode; | |
| tegra_i2c_config_fifo_trig(i2c_dev, xfer_size); | |
| /* | |
| * Transfer time in mSec = Total bits / transfer rate | |
| * Total bits = 9 bits per byte (including ACK bit) + Start & stop bits | |
| */ | |
| xfer_time += DIV_ROUND_CLOSEST(((xfer_size * 9) + 2) * MSEC_PER_SEC, | |
| i2c_dev->timings.bus_freq_hz); | |
| int_mask = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST; | |
| tegra_i2c_unmask_irq(i2c_dev, int_mask); | |
| if (i2c_dev->dma_mode) { | |
| if (i2c_dev->msg_read) { | |
| err = tegra_i2c_dma_submit(i2c_dev, xfer_size); | |
| if (err) | |
| return err; | |
| } | |
| } | |
| tegra_i2c_push_packet_header(i2c_dev, msg, end_state); | |
| if (!i2c_dev->msg_read) { | |
| if (i2c_dev->dma_mode) { | |
| memcpy(i2c_dev->dma_buf + I2C_PACKET_HEADER_SIZE, | |
| msg->buf, i2c_dev->msg_len); | |
| err = tegra_i2c_dma_submit(i2c_dev, xfer_size); | |
| if (err) | |
| return err; | |
| } else { | |
| tegra_i2c_fill_tx_fifo(i2c_dev); | |
| } | |
| } | |
| if (i2c_dev->hw->has_per_pkt_xfer_complete_irq) | |
| int_mask |= I2C_INT_PACKET_XFER_COMPLETE; | |
| if (!i2c_dev->dma_mode) { | |
| if (msg->flags & I2C_M_RD) | |
| int_mask |= I2C_INT_RX_FIFO_DATA_REQ; | |
| else if (i2c_dev->msg_buf_remaining) | |
| int_mask |= I2C_INT_TX_FIFO_DATA_REQ; | |
| } | |
| tegra_i2c_unmask_irq(i2c_dev, int_mask); | |
| dev_dbg(i2c_dev->dev, "unmasked IRQ: %02x\n", | |
| i2c_readl(i2c_dev, i2c_dev->hw->regs->int_mask)); | |
| if (i2c_dev->dma_mode) { | |
| time_left = tegra_i2c_wait_completion(i2c_dev, | |
| &i2c_dev->dma_complete, | |
| xfer_time); | |
| /* | |
| * Synchronize DMA first, since dmaengine_terminate_sync() | |
| * performs synchronization after the transfer's termination | |
| * and we want to get a completion if transfer succeeded. | |
| */ | |
| dmaengine_synchronize(i2c_dev->dma_chan); | |
| dmaengine_terminate_sync(i2c_dev->dma_chan); | |
| if (!time_left && !completion_done(&i2c_dev->dma_complete)) { | |
| tegra_i2c_init(i2c_dev); | |
| return -ETIMEDOUT; | |
| } | |
| if (i2c_dev->msg_read && i2c_dev->msg_err == I2C_ERR_NONE) | |
| memcpy(i2c_dev->msg_buf, i2c_dev->dma_buf, i2c_dev->msg_len); | |
| } | |
| time_left = tegra_i2c_wait_completion(i2c_dev, &i2c_dev->msg_complete, | |
| xfer_time); | |
| tegra_i2c_mask_irq(i2c_dev, int_mask); | |
| if (time_left == 0) { | |
| tegra_i2c_init(i2c_dev); | |
| return -ETIMEDOUT; | |
| } | |
| dev_dbg(i2c_dev->dev, "transfer complete: %lu %d %d\n", | |
| time_left, completion_done(&i2c_dev->msg_complete), | |
| i2c_dev->msg_err); | |
| i2c_dev->dma_mode = false; | |
| err = tegra_i2c_error_recover(i2c_dev, msg); | |
| if (err) | |
| return err; | |
| return 0; | |
| } | |
| static int tegra_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], | |
| int num) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | |
| int i, ret; | |
| ret = pm_runtime_get_sync(i2c_dev->dev); | |
| if (ret < 0) { | |
| dev_err(i2c_dev->dev, "runtime resume failed %d\n", ret); | |
| pm_runtime_put_noidle(i2c_dev->dev); | |
| return ret; | |
| } | |
| ret = tegra_i2c_mutex_lock(i2c_dev); | |
| if (ret) { | |
| pm_runtime_put(i2c_dev->dev); | |
| return ret; | |
| } | |
| for (i = 0; i < num; i++) { | |
| enum msg_end_type end_type = MSG_END_STOP; | |
| if (i < (num - 1)) { | |
| /* check whether follow up message is coming */ | |
| if (msgs[i + 1].flags & I2C_M_NOSTART) | |
| end_type = MSG_END_CONTINUE; | |
| else | |
| end_type = MSG_END_REPEAT_START; | |
| } | |
| /* If M_RECV_LEN use ContinueXfer to read the first byte */ | |
| if (msgs[i].flags & I2C_M_RECV_LEN) { | |
| ret = tegra_i2c_xfer_msg(i2c_dev, &msgs[i], MSG_END_CONTINUE); | |
| if (ret) | |
| break; | |
| /* Validate message length before proceeding */ | |
| if (msgs[i].buf[0] == 0 || msgs[i].buf[0] > I2C_SMBUS_BLOCK_MAX) | |
| break; | |
| /* Set the msg length from first byte */ | |
| msgs[i].len += msgs[i].buf[0]; | |
| dev_dbg(i2c_dev->dev, "reading %d bytes\n", msgs[i].len); | |
| } | |
| ret = tegra_i2c_xfer_msg(i2c_dev, &msgs[i], end_type); | |
| if (ret) | |
| break; | |
| } | |
| tegra_i2c_mutex_unlock(i2c_dev); | |
| pm_runtime_put(i2c_dev->dev); | |
| return ret ?: i; | |
| } | |
| static int tegra_i2c_xfer_atomic(struct i2c_adapter *adap, | |
| struct i2c_msg msgs[], int num) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | |
| int ret; | |
| i2c_dev->atomic_mode = true; | |
| ret = tegra_i2c_xfer(adap, msgs, num); | |
| i2c_dev->atomic_mode = false; | |
| return ret; | |
| } | |
| static u32 tegra_i2c_func(struct i2c_adapter *adap) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | |
| u32 ret = I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | | |
| I2C_FUNC_10BIT_ADDR | I2C_FUNC_PROTOCOL_MANGLING; | |
| if (i2c_dev->hw->has_continue_xfer_support) | |
| ret |= I2C_FUNC_NOSTART | I2C_FUNC_SMBUS_READ_BLOCK_DATA; | |
| return ret; | |
| } | |
| static const struct i2c_algorithm tegra_i2c_algo = { | |
| .xfer = tegra_i2c_xfer, | |
| .xfer_atomic = tegra_i2c_xfer_atomic, | |
| .functionality = tegra_i2c_func, | |
| }; | |
| /* payload size is only 12 bit */ | |
| static const struct i2c_adapter_quirks tegra_i2c_quirks = { | |
| .flags = I2C_AQ_NO_ZERO_LEN, | |
| .max_read_len = SZ_4K, | |
| .max_write_len = SZ_4K - I2C_PACKET_HEADER_SIZE, | |
| }; | |
| static const struct i2c_adapter_quirks tegra194_i2c_quirks = { | |
| .flags = I2C_AQ_NO_ZERO_LEN, | |
| .max_write_len = SZ_64K - I2C_PACKET_HEADER_SIZE, | |
| }; | |
| static struct i2c_bus_recovery_info tegra_i2c_recovery_info = { | |
| .recover_bus = tegra_i2c_issue_bus_clear, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra20_i2c_hw = { | |
| .has_continue_xfer_support = false, | |
| .has_per_pkt_xfer_complete_irq = false, | |
| .clk_divisor_hs_mode = 3, | |
| .clk_divisor_std_mode = 0, | |
| .clk_divisor_fast_mode = 0, | |
| .clk_divisor_fast_plus_mode = 0, | |
| .has_config_load_reg = false, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = false, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = false, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x0, | |
| .setup_hold_time_fast_mode = 0x0, | |
| .setup_hold_time_fastplus_mode = 0x0, | |
| .setup_hold_time_hs_mode = 0x0, | |
| .has_interface_timing_reg = false, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) | |
| static const struct tegra_i2c_hw_feature tegra20_dvc_i2c_hw = { | |
| .has_continue_xfer_support = false, | |
| .has_per_pkt_xfer_complete_irq = false, | |
| .clk_divisor_hs_mode = 3, | |
| .clk_divisor_std_mode = 0, | |
| .clk_divisor_fast_mode = 0, | |
| .clk_divisor_fast_plus_mode = 0, | |
| .has_config_load_reg = false, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = false, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = false, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x0, | |
| .setup_hold_time_fast_mode = 0x0, | |
| .setup_hold_time_fastplus_mode = 0x0, | |
| .setup_hold_time_hs_mode = 0x0, | |
| .has_interface_timing_reg = false, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DVC, | |
| .regs = &tegra20_dvc_i2c_regs, | |
| }; | |
| #endif | |
| static const struct tegra_i2c_hw_feature tegra30_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = false, | |
| .clk_divisor_hs_mode = 3, | |
| .clk_divisor_std_mode = 0, | |
| .clk_divisor_fast_mode = 0, | |
| .clk_divisor_fast_plus_mode = 0, | |
| .has_config_load_reg = false, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = false, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = false, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x0, | |
| .setup_hold_time_fast_mode = 0x0, | |
| .setup_hold_time_fastplus_mode = 0x0, | |
| .setup_hold_time_hs_mode = 0x0, | |
| .has_interface_timing_reg = false, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra114_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x19, | |
| .clk_divisor_fast_mode = 0x19, | |
| .clk_divisor_fast_plus_mode = 0x10, | |
| .has_config_load_reg = false, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = false, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x0, | |
| .setup_hold_time_fast_mode = 0x0, | |
| .setup_hold_time_fastplus_mode = 0x0, | |
| .setup_hold_time_hs_mode = 0x0, | |
| .has_interface_timing_reg = false, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra124_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x19, | |
| .clk_divisor_fast_mode = 0x19, | |
| .clk_divisor_fast_plus_mode = 0x10, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x0, | |
| .setup_hold_time_fast_mode = 0x0, | |
| .setup_hold_time_fastplus_mode = 0x0, | |
| .setup_hold_time_hs_mode = 0x0, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra210_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x19, | |
| .clk_divisor_fast_mode = 0x19, | |
| .clk_divisor_fast_plus_mode = 0x10, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0, | |
| .setup_hold_time_fast_mode = 0, | |
| .setup_hold_time_fastplus_mode = 0, | |
| .setup_hold_time_hs_mode = 0, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC) | |
| static const struct tegra_i2c_hw_feature tegra210_vi_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x19, | |
| .clk_divisor_fast_mode = 0x19, | |
| .clk_divisor_fast_plus_mode = 0x10, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = true, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x2, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0, | |
| .setup_hold_time_fast_mode = 0, | |
| .setup_hold_time_fastplus_mode = 0, | |
| .setup_hold_time_hs_mode = 0, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_VI, | |
| .regs = &tegra210_vi_i2c_regs, | |
| }; | |
| #endif | |
| static const struct tegra_i2c_hw_feature tegra186_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x16, | |
| .clk_divisor_fast_mode = 0x19, | |
| .clk_divisor_fast_plus_mode = 0x10, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = false, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = false, | |
| .has_mst_reset = false, | |
| .quirks = &tegra_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = false, | |
| .tlow_std_mode = 0x4, | |
| .thigh_std_mode = 0x3, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x2, | |
| .setup_hold_time_std_mode = 0, | |
| .setup_hold_time_fast_mode = 0, | |
| .setup_hold_time_fastplus_mode = 0, | |
| .setup_hold_time_hs_mode = 0, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = false, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra194_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x4f, | |
| .clk_divisor_fast_mode = 0x3c, | |
| .clk_divisor_fast_plus_mode = 0x16, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = true, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = true, | |
| .has_mst_reset = true, | |
| .quirks = &tegra194_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = false, | |
| .tlow_std_mode = 0x8, | |
| .thigh_std_mode = 0x7, | |
| .tlow_fast_mode = 0x2, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x2, | |
| .thigh_fastplus_mode = 0x2, | |
| .tlow_hs_mode = 0x8, | |
| .thigh_hs_mode = 0x3, | |
| .setup_hold_time_std_mode = 0x08080808, | |
| .setup_hold_time_fast_mode = 0x02020202, | |
| .setup_hold_time_fastplus_mode = 0x02020202, | |
| .setup_hold_time_hs_mode = 0x090909, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = true, | |
| .has_mutex = false, | |
| .has_fairarb_reg = false, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra20_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra256_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 9, | |
| .clk_divisor_std_mode = 0x7a, | |
| .clk_divisor_fast_mode = 0x40, | |
| .clk_divisor_fast_plus_mode = 0x14, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = true, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = true, | |
| .has_mst_reset = true, | |
| .quirks = &tegra194_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = false, | |
| .tlow_std_mode = 0x8, | |
| .thigh_std_mode = 0x7, | |
| .tlow_fast_mode = 0x4, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x4, | |
| .thigh_fastplus_mode = 0x4, | |
| .tlow_hs_mode = 0x3, | |
| .thigh_hs_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x08080808, | |
| .setup_hold_time_fast_mode = 0x04010101, | |
| .setup_hold_time_fastplus_mode = 0x04020202, | |
| .setup_hold_time_hs_mode = 0x030303, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = true, | |
| .has_mutex = true, | |
| .has_fairarb_reg = true, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra264_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra264_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 1, | |
| .clk_divisor_std_mode = 0x1d, | |
| .clk_divisor_fast_mode = 0x15, | |
| .clk_divisor_fast_plus_mode = 0x8, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = true, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = true, | |
| .has_mst_reset = true, | |
| .quirks = &tegra194_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = false, | |
| .tlow_std_mode = 0x8, | |
| .thigh_std_mode = 0x7, | |
| .tlow_fast_mode = 0x2, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x2, | |
| .thigh_fastplus_mode = 0x2, | |
| .tlow_hs_mode = 0x4, | |
| .thigh_hs_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x08080808, | |
| .setup_hold_time_fast_mode = 0x02020202, | |
| .setup_hold_time_fastplus_mode = 0x02020202, | |
| .setup_hold_time_hs_mode = 0x090909, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = true, | |
| .has_mutex = true, | |
| .has_fairarb_reg = true, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra264_i2c_regs, | |
| }; | |
| static const struct tegra_i2c_hw_feature tegra410_i2c_hw = { | |
| .has_continue_xfer_support = true, | |
| .has_per_pkt_xfer_complete_irq = true, | |
| .clk_divisor_hs_mode = 2, | |
| .clk_divisor_std_mode = 0x3f, | |
| .clk_divisor_fast_mode = 0x2f, | |
| .clk_divisor_fast_plus_mode = 0x11, | |
| .has_config_load_reg = true, | |
| .has_multi_master_mode = true, | |
| .has_slcg_override_reg = true, | |
| .has_mst_fifo = true, | |
| .has_mst_reset = true, | |
| .quirks = &tegra194_i2c_quirks, | |
| .supports_bus_clear = true, | |
| .has_apb_dma = false, | |
| .tlow_std_mode = 0x8, | |
| .thigh_std_mode = 0x7, | |
| .tlow_fast_mode = 0x2, | |
| .thigh_fast_mode = 0x2, | |
| .tlow_fastplus_mode = 0x2, | |
| .thigh_fastplus_mode = 0x2, | |
| .tlow_hs_mode = 0x5, | |
| .thigh_hs_mode = 0x2, | |
| .setup_hold_time_std_mode = 0x08080808, | |
| .setup_hold_time_fast_mode = 0x02020202, | |
| .setup_hold_time_fastplus_mode = 0x02020202, | |
| .setup_hold_time_hs_mode = 0x0b0b0b, | |
| .has_interface_timing_reg = true, | |
| .enable_hs_mode_support = true, | |
| .has_mutex = true, | |
| .has_fairarb_reg = true, | |
| .variant = TEGRA_I2C_VARIANT_DEFAULT, | |
| .regs = &tegra410_i2c_regs, | |
| }; | |
| static const struct of_device_id tegra_i2c_of_match[] = { | |
| { .compatible = "nvidia,tegra264-i2c", .data = &tegra264_i2c_hw, }, | |
| { .compatible = "nvidia,tegra256-i2c", .data = &tegra256_i2c_hw, }, | |
| { .compatible = "nvidia,tegra194-i2c", .data = &tegra194_i2c_hw, }, | |
| { .compatible = "nvidia,tegra186-i2c", .data = &tegra186_i2c_hw, }, | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC) | |
| { .compatible = "nvidia,tegra210-i2c-vi", .data = &tegra210_vi_i2c_hw, }, | |
| #endif | |
| { .compatible = "nvidia,tegra210-i2c", .data = &tegra210_i2c_hw, }, | |
| { .compatible = "nvidia,tegra124-i2c", .data = &tegra124_i2c_hw, }, | |
| { .compatible = "nvidia,tegra114-i2c", .data = &tegra114_i2c_hw, }, | |
| { .compatible = "nvidia,tegra30-i2c", .data = &tegra30_i2c_hw, }, | |
| { .compatible = "nvidia,tegra20-i2c", .data = &tegra20_i2c_hw, }, | |
| #if IS_ENABLED(CONFIG_ARCH_TEGRA_2x_SOC) | |
| { .compatible = "nvidia,tegra20-i2c-dvc", .data = &tegra20_dvc_i2c_hw, }, | |
| #endif | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(of, tegra_i2c_of_match); | |
| static void tegra_i2c_parse_dt(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| bool multi_mode; | |
| i2c_parse_fw_timings(i2c_dev->dev, &i2c_dev->timings, true); | |
| multi_mode = device_property_read_bool(i2c_dev->dev, "multi-master"); | |
| i2c_dev->multimaster_mode = multi_mode; | |
| i2c_dev->is_mctp = device_property_present(i2c_dev->dev, "mctp-controller"); | |
| } | |
| static int tegra_i2c_init_clocks(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| int err; | |
| if (ACPI_HANDLE(i2c_dev->dev)) | |
| return 0; | |
| i2c_dev->clocks[i2c_dev->nclocks++].id = "div-clk"; | |
| if (i2c_dev->hw == &tegra20_i2c_hw || i2c_dev->hw == &tegra30_i2c_hw) | |
| i2c_dev->clocks[i2c_dev->nclocks++].id = "fast-clk"; | |
| if (IS_VI(i2c_dev)) | |
| i2c_dev->clocks[i2c_dev->nclocks++].id = "slow"; | |
| err = devm_clk_bulk_get(i2c_dev->dev, i2c_dev->nclocks, | |
| i2c_dev->clocks); | |
| if (err) | |
| return err; | |
| err = clk_bulk_prepare(i2c_dev->nclocks, i2c_dev->clocks); | |
| if (err) | |
| return err; | |
| i2c_dev->div_clk = i2c_dev->clocks[0].clk; | |
| if (!i2c_dev->multimaster_mode) | |
| return 0; | |
| err = clk_enable(i2c_dev->div_clk); | |
| if (err) { | |
| dev_err_probe(i2c_dev->dev, err, "failed to enable div-clk\n"); | |
| goto unprepare_clocks; | |
| } | |
| return 0; | |
| unprepare_clocks: | |
| clk_bulk_unprepare(i2c_dev->nclocks, i2c_dev->clocks); | |
| return err; | |
| } | |
| static void tegra_i2c_release_clocks(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| if (i2c_dev->multimaster_mode) | |
| clk_disable(i2c_dev->div_clk); | |
| clk_bulk_unprepare(i2c_dev->nclocks, i2c_dev->clocks); | |
| } | |
| static int tegra_i2c_init_hardware(struct tegra_i2c_dev *i2c_dev) | |
| { | |
| int ret; | |
| ret = pm_runtime_get_sync(i2c_dev->dev); | |
| if (ret < 0) | |
| dev_err_probe(i2c_dev->dev, ret, "runtime resume failed\n"); | |
| else | |
| ret = tegra_i2c_init(i2c_dev); | |
| pm_runtime_put_sync(i2c_dev->dev); | |
| return ret; | |
| } | |
| static int tegra_i2c_probe(struct platform_device *pdev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev; | |
| struct resource *res; | |
| int err; | |
| i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL); | |
| if (!i2c_dev) | |
| return -ENOMEM; | |
| platform_set_drvdata(pdev, i2c_dev); | |
| init_completion(&i2c_dev->msg_complete); | |
| init_completion(&i2c_dev->dma_complete); | |
| i2c_dev->hw = device_get_match_data(&pdev->dev); | |
| i2c_dev->cont_id = pdev->id; | |
| i2c_dev->dev = &pdev->dev; | |
| i2c_dev->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res); | |
| if (IS_ERR(i2c_dev->base)) | |
| return PTR_ERR(i2c_dev->base); | |
| i2c_dev->base_phys = res->start; | |
| err = platform_get_irq(pdev, 0); | |
| if (err < 0) | |
| return err; | |
| i2c_dev->irq = err; | |
| /* interrupt will be enabled during of transfer time */ | |
| irq_set_status_flags(i2c_dev->irq, IRQ_NOAUTOEN); | |
| err = devm_request_threaded_irq(i2c_dev->dev, i2c_dev->irq, | |
| NULL, tegra_i2c_isr, | |
| IRQF_NO_SUSPEND | IRQF_ONESHOT, | |
| dev_name(i2c_dev->dev), i2c_dev); | |
| if (err) | |
| return err; | |
| tegra_i2c_parse_dt(i2c_dev); | |
| err = tegra_i2c_init_clocks(i2c_dev); | |
| if (err) | |
| return err; | |
| err = tegra_i2c_init_dma(i2c_dev); | |
| if (err) | |
| goto release_clocks; | |
| /* | |
| * VI I2C is in VE power domain which is not always ON and not | |
| * IRQ-safe. Thus, IRQ-safe device shouldn't be attached to a | |
| * non IRQ-safe domain because this prevents powering off the power | |
| * domain. | |
| * | |
| * VI I2C device shouldn't be marked as IRQ-safe because VI I2C won't | |
| * be used for atomic transfers. ACPI device is not IRQ safe also. | |
| * | |
| * Devices with pinctrl states cannot be marked IRQ-safe as the pinctrl | |
| * state transitions during runtime PM require mutexes. | |
| */ | |
| if (!IS_VI(i2c_dev) && !has_acpi_companion(i2c_dev->dev) && !i2c_dev->dev->pins) | |
| pm_runtime_irq_safe(i2c_dev->dev); | |
| pm_runtime_enable(i2c_dev->dev); | |
| err = tegra_i2c_init_hardware(i2c_dev); | |
| if (err) | |
| goto release_rpm; | |
| i2c_set_adapdata(&i2c_dev->adapter, i2c_dev); | |
| i2c_dev->adapter.dev.of_node = i2c_dev->dev->of_node; | |
| i2c_dev->adapter.dev.parent = i2c_dev->dev; | |
| i2c_dev->adapter.retries = 1; | |
| i2c_dev->adapter.timeout = 6 * HZ; | |
| i2c_dev->adapter.quirks = i2c_dev->hw->quirks; | |
| i2c_dev->adapter.owner = THIS_MODULE; | |
| i2c_dev->adapter.class = I2C_CLASS_DEPRECATED; | |
| i2c_dev->adapter.algo = &tegra_i2c_algo; | |
| i2c_dev->adapter.nr = pdev->id; | |
| ACPI_COMPANION_SET(&i2c_dev->adapter.dev, ACPI_COMPANION(&pdev->dev)); | |
| if (i2c_dev->hw->supports_bus_clear) | |
| i2c_dev->adapter.bus_recovery_info = &tegra_i2c_recovery_info; | |
| strscpy(i2c_dev->adapter.name, dev_name(i2c_dev->dev), | |
| sizeof(i2c_dev->adapter.name)); | |
| err = i2c_add_numbered_adapter(&i2c_dev->adapter); | |
| if (err) | |
| goto release_rpm; | |
| return 0; | |
| release_rpm: | |
| pm_runtime_disable(i2c_dev->dev); | |
| tegra_i2c_release_dma(i2c_dev); | |
| release_clocks: | |
| tegra_i2c_release_clocks(i2c_dev); | |
| return err; | |
| } | |
| static void tegra_i2c_remove(struct platform_device *pdev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = platform_get_drvdata(pdev); | |
| i2c_del_adapter(&i2c_dev->adapter); | |
| pm_runtime_force_suspend(i2c_dev->dev); | |
| tegra_i2c_release_dma(i2c_dev); | |
| tegra_i2c_release_clocks(i2c_dev); | |
| } | |
| static int __maybe_unused tegra_i2c_runtime_resume(struct device *dev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev); | |
| int err; | |
| err = pinctrl_pm_select_default_state(dev); | |
| if (err) | |
| return err; | |
| err = clk_bulk_enable(i2c_dev->nclocks, i2c_dev->clocks); | |
| if (err) | |
| return err; | |
| /* | |
| * VI I2C device is attached to VE power domain which goes through | |
| * power ON/OFF during runtime PM resume/suspend, meaning that | |
| * controller needs to be re-initialized after power ON. | |
| */ | |
| if (IS_VI(i2c_dev)) { | |
| err = tegra_i2c_init(i2c_dev); | |
| if (err) | |
| goto disable_clocks; | |
| } | |
| return 0; | |
| disable_clocks: | |
| clk_bulk_disable(i2c_dev->nclocks, i2c_dev->clocks); | |
| return err; | |
| } | |
| static int __maybe_unused tegra_i2c_runtime_suspend(struct device *dev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev); | |
| clk_bulk_disable(i2c_dev->nclocks, i2c_dev->clocks); | |
| return pinctrl_pm_select_idle_state(dev); | |
| } | |
| static int __maybe_unused tegra_i2c_suspend(struct device *dev) | |
| { | |
| /* | |
| * Bring the controller up and hold a usage count so it stays | |
| * available until the noirq phase. | |
| */ | |
| return pm_runtime_resume_and_get(dev); | |
| } | |
| static int __maybe_unused tegra_i2c_suspend_noirq(struct device *dev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev); | |
| i2c_mark_adapter_suspended(&i2c_dev->adapter); | |
| /* | |
| * Runtime PM is already disabled at this point, so invoke the | |
| * runtime_suspend callback directly to put the controller down. | |
| */ | |
| return tegra_i2c_runtime_suspend(dev); | |
| } | |
| static int __maybe_unused tegra_i2c_resume_noirq(struct device *dev) | |
| { | |
| struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev); | |
| int err; | |
| /* | |
| * Runtime PM is still disabled at this point, so invoke the | |
| * runtime_resume callback directly to bring the controller back up | |
| * before re-initializing the hardware. The adapter is then marked | |
| * resumed so that consumers can issue transfers from their own | |
| * resume_noirq() handlers and onwards. | |
| */ | |
| err = tegra_i2c_runtime_resume(dev); | |
| if (err) | |
| return err; | |
| err = tegra_i2c_init(i2c_dev); | |
| if (err) | |
| return err; | |
| i2c_mark_adapter_resumed(&i2c_dev->adapter); | |
| return 0; | |
| } | |
| static int __maybe_unused tegra_i2c_resume(struct device *dev) | |
| { | |
| pm_runtime_put(dev); | |
| return 0; | |
| } | |
| static const struct dev_pm_ops tegra_i2c_pm = { | |
| SET_SYSTEM_SLEEP_PM_OPS(tegra_i2c_suspend, tegra_i2c_resume) | |
| SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(tegra_i2c_suspend_noirq, | |
| tegra_i2c_resume_noirq) | |
| SET_RUNTIME_PM_OPS(tegra_i2c_runtime_suspend, tegra_i2c_runtime_resume, | |
| NULL) | |
| }; | |
| static const struct acpi_device_id tegra_i2c_acpi_match[] = { | |
| {.id = "NVDA0101", .driver_data = (kernel_ulong_t)&tegra210_i2c_hw}, | |
| {.id = "NVDA0201", .driver_data = (kernel_ulong_t)&tegra186_i2c_hw}, | |
| {.id = "NVDA0301", .driver_data = (kernel_ulong_t)&tegra194_i2c_hw}, | |
| {.id = "NVDA2017", .driver_data = (kernel_ulong_t)&tegra410_i2c_hw}, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(acpi, tegra_i2c_acpi_match); | |
| static struct platform_driver tegra_i2c_driver = { | |
| .probe = tegra_i2c_probe, | |
| .remove = tegra_i2c_remove, | |
| .driver = { | |
| .name = "tegra-i2c", | |
| .of_match_table = tegra_i2c_of_match, | |
| .acpi_match_table = tegra_i2c_acpi_match, | |
| .pm = &tegra_i2c_pm, | |
| }, | |
| }; | |
| module_platform_driver(tegra_i2c_driver); | |
| MODULE_DESCRIPTION("NVIDIA Tegra I2C Bus Controller driver"); | |
| MODULE_AUTHOR("Colin Cross"); | |
| MODULE_LICENSE("GPL v2"); |