| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright (C) 2015 Broadcom | |
| */ | |
| /** | |
| * DOC: VC4 CRTC module | |
| * | |
| * In VC4, the Pixel Valve is what most closely corresponds to the | |
| * DRM's concept of a CRTC. The PV generates video timings from the | |
| * encoder's clock plus its configuration. It pulls scaled pixels from | |
| * the HVS at that timing, and feeds it to the encoder. | |
| * | |
| * However, the DRM CRTC also collects the configuration of all the | |
| * DRM planes attached to it. As a result, the CRTC is also | |
| * responsible for writing the display list for the HVS channel that | |
| * the CRTC will use. | |
| * | |
| * The 2835 has 3 different pixel valves. pv0 in the audio power | |
| * domain feeds DSI0 or DPI, while pv1 feeds DS1 or SMI. pv2 in the | |
| * image domain can feed either HDMI or the SDTV controller. The | |
| * pixel valve chooses from the CPRMAN clocks (HSM for HDMI, VEC for | |
| * SDTV, etc.) according to which output type is chosen in the mux. | |
| * | |
| * For power management, the pixel valve's registers are all clocked | |
| * by the AXI clock, while the timings and FIFOs make use of the | |
| * output-specific clock. Since the encoders also directly consume | |
| * the CPRMAN clocks, and know what timings they need, they are the | |
| * ones that set the clock. | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/component.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pm_runtime.h> | |
| #include <drm/drm_atomic.h> | |
| #include <drm/drm_atomic_helper.h> | |
| #include <drm/drm_atomic_uapi.h> | |
| #include <drm/drm_fb_dma_helper.h> | |
| #include <drm/drm_framebuffer.h> | |
| #include <drm/drm_drv.h> | |
| #include <drm/drm_print.h> | |
| #include <drm/drm_probe_helper.h> | |
| #include <drm/drm_vblank.h> | |
| #include "vc4_drv.h" | |
| #include "vc4_hdmi.h" | |
| #include "vc4_regs.h" | |
| #define HVS_FIFO_LATENCY_PIX 6 | |
| #define CRTC_WRITE(offset, val) \ | |
| do { \ | |
| kunit_fail_current_test("Accessing a register in a unit test!\n"); \ | |
| writel(val, vc4_crtc->regs + (offset)); \ | |
| } while (0) | |
| #define CRTC_READ(offset) \ | |
| ({ \ | |
| kunit_fail_current_test("Accessing a register in a unit test!\n"); \ | |
| readl(vc4_crtc->regs + (offset)); \ | |
| }) | |
| static const struct debugfs_reg32 crtc_regs[] = { | |
| VC4_REG32(PV_CONTROL), | |
| VC4_REG32(PV_V_CONTROL), | |
| VC4_REG32(PV_VSYNCD_EVEN), | |
| VC4_REG32(PV_HORZA), | |
| VC4_REG32(PV_HORZB), | |
| VC4_REG32(PV_VERTA), | |
| VC4_REG32(PV_VERTB), | |
| VC4_REG32(PV_VERTA_EVEN), | |
| VC4_REG32(PV_VERTB_EVEN), | |
| VC4_REG32(PV_INTEN), | |
| VC4_REG32(PV_INTSTAT), | |
| VC4_REG32(PV_STAT), | |
| VC4_REG32(PV_HACT_ACT), | |
| }; | |
| static unsigned int | |
| vc4_crtc_get_cob_allocation(struct vc4_dev *vc4, unsigned int channel) | |
| { | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| u32 dispbase, top, base; | |
| /* Top/base are supposed to be 4-pixel aligned, but the | |
| * Raspberry Pi firmware fills the low bits (which are | |
| * presumably ignored). | |
| */ | |
| if (vc4->gen >= VC4_GEN_6_C) { | |
| dispbase = HVS_READ(SCALER6_DISPX_COB(channel)); | |
| top = VC4_GET_FIELD(dispbase, SCALER6_DISPX_COB_TOP) & ~3; | |
| base = VC4_GET_FIELD(dispbase, SCALER6_DISPX_COB_BASE) & ~3; | |
| } else { | |
| dispbase = HVS_READ(SCALER_DISPBASEX(channel)); | |
| top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3; | |
| base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3; | |
| } | |
| return top - base + 4; | |
| } | |
| static bool vc4_crtc_get_scanout_position(struct drm_crtc *crtc, | |
| bool in_vblank_irq, | |
| int *vpos, int *hpos, | |
| ktime_t *stime, ktime_t *etime, | |
| const struct drm_display_mode *mode) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct vc4_crtc_state *vc4_crtc_state = to_vc4_crtc_state(crtc->state); | |
| unsigned int channel = vc4_crtc_state->assigned_channel; | |
| unsigned int cob_size; | |
| u32 val; | |
| int fifo_lines; | |
| int vblank_lines; | |
| bool ret = false; | |
| /* preempt_disable_rt() should go right here in PREEMPT_RT patchset. */ | |
| /* Get optional system timestamp before query. */ | |
| if (stime) | |
| *stime = ktime_get(); | |
| /* | |
| * Read vertical scanline which is currently composed for our | |
| * pixelvalve by the HVS, and also the scaler status. | |
| */ | |
| if (vc4->gen >= VC4_GEN_6_C) | |
| val = HVS_READ(SCALER6_DISPX_STATUS(channel)); | |
| else | |
| val = HVS_READ(SCALER_DISPSTATX(channel)); | |
| /* Get optional system timestamp after query. */ | |
| if (etime) | |
| *etime = ktime_get(); | |
| /* preempt_enable_rt() should go right here in PREEMPT_RT patchset. */ | |
| /* Vertical position of hvs composed scanline. */ | |
| if (vc4->gen >= VC4_GEN_6_C) | |
| *vpos = VC4_GET_FIELD(val, SCALER6_DISPX_STATUS_YLINE); | |
| else | |
| *vpos = VC4_GET_FIELD(val, SCALER_DISPSTATX_LINE); | |
| *hpos = 0; | |
| if (mode->flags & DRM_MODE_FLAG_INTERLACE) { | |
| *vpos /= 2; | |
| /* Use hpos to correct for field offset in interlaced mode. */ | |
| if (vc4_hvs_get_fifo_frame_count(hvs, channel) % 2) | |
| *hpos += mode->crtc_htotal / 2; | |
| } | |
| cob_size = vc4_crtc_get_cob_allocation(vc4, channel); | |
| /* This is the offset we need for translating hvs -> pv scanout pos. */ | |
| fifo_lines = cob_size / mode->crtc_hdisplay; | |
| if (fifo_lines > 0) | |
| ret = true; | |
| /* HVS more than fifo_lines into frame for compositing? */ | |
| if (*vpos > fifo_lines) { | |
| /* | |
| * We are in active scanout and can get some meaningful results | |
| * from HVS. The actual PV scanout can not trail behind more | |
| * than fifo_lines as that is the fifo's capacity. Assume that | |
| * in active scanout the HVS and PV work in lockstep wrt. HVS | |
| * refilling the fifo and PV consuming from the fifo, ie. | |
| * whenever the PV consumes and frees up a scanline in the | |
| * fifo, the HVS will immediately refill it, therefore | |
| * incrementing vpos. Therefore we choose HVS read position - | |
| * fifo size in scanlines as a estimate of the real scanout | |
| * position of the PV. | |
| */ | |
| *vpos -= fifo_lines + 1; | |
| return ret; | |
| } | |
| /* | |
| * Less: This happens when we are in vblank and the HVS, after getting | |
| * the VSTART restart signal from the PV, just started refilling its | |
| * fifo with new lines from the top-most lines of the new framebuffers. | |
| * The PV does not scan out in vblank, so does not remove lines from | |
| * the fifo, so the fifo will be full quickly and the HVS has to pause. | |
| * We can't get meaningful readings wrt. scanline position of the PV | |
| * and need to make things up in a approximative but consistent way. | |
| */ | |
| vblank_lines = mode->vtotal - mode->vdisplay; | |
| if (in_vblank_irq) { | |
| /* | |
| * Assume the irq handler got called close to first | |
| * line of vblank, so PV has about a full vblank | |
| * scanlines to go, and as a base timestamp use the | |
| * one taken at entry into vblank irq handler, so it | |
| * is not affected by random delays due to lock | |
| * contention on event_lock or vblank_time lock in | |
| * the core. | |
| */ | |
| *vpos = -vblank_lines; | |
| if (stime) | |
| *stime = vc4_crtc->t_vblank; | |
| if (etime) | |
| *etime = vc4_crtc->t_vblank; | |
| /* | |
| * If the HVS fifo is not yet full then we know for certain | |
| * we are at the very beginning of vblank, as the hvs just | |
| * started refilling, and the stime and etime timestamps | |
| * truly correspond to start of vblank. | |
| * | |
| * Unfortunately there's no way to report this to upper levels | |
| * and make it more useful. | |
| */ | |
| } else { | |
| /* | |
| * No clue where we are inside vblank. Return a vpos of zero, | |
| * which will cause calling code to just return the etime | |
| * timestamp uncorrected. At least this is no worse than the | |
| * standard fallback. | |
| */ | |
| *vpos = 0; | |
| } | |
| return ret; | |
| } | |
| static u32 vc4_get_fifo_full_level(struct vc4_crtc *vc4_crtc, u32 format) | |
| { | |
| const struct vc4_crtc_data *crtc_data = vc4_crtc_to_vc4_crtc_data(vc4_crtc); | |
| const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc); | |
| struct vc4_dev *vc4 = to_vc4_dev(vc4_crtc->base.dev); | |
| /* | |
| * NOTE: Could we use register 0x68 (PV_HW_CFG1) to get the FIFO | |
| * size? | |
| */ | |
| u32 fifo_len_bytes = pv_data->fifo_depth; | |
| /* | |
| * Pixels are pulled from the HVS if the number of bytes is | |
| * lower than the FIFO full level. | |
| * | |
| * The latency of the pixel fetch mechanism is 6 pixels, so we | |
| * need to convert those 6 pixels in bytes, depending on the | |
| * format, and then subtract that from the length of the FIFO | |
| * to make sure we never end up in a situation where the FIFO | |
| * is full. | |
| */ | |
| switch (format) { | |
| case PV_CONTROL_FORMAT_DSIV_16: | |
| case PV_CONTROL_FORMAT_DSIC_16: | |
| return fifo_len_bytes - 2 * HVS_FIFO_LATENCY_PIX; | |
| case PV_CONTROL_FORMAT_DSIV_18: | |
| return fifo_len_bytes - 14; | |
| case PV_CONTROL_FORMAT_24: | |
| case PV_CONTROL_FORMAT_DSIV_24: | |
| default: | |
| /* | |
| * For some reason, the pixelvalve4 doesn't work with | |
| * the usual formula and will only work with 32. | |
| */ | |
| if (crtc_data->hvs_output == 5) | |
| return 32; | |
| /* | |
| * It looks like in some situations, we will overflow | |
| * the PixelValve FIFO (with the bit 10 of PV stat being | |
| * set) and stall the HVS / PV, eventually resulting in | |
| * a page flip timeout. | |
| * | |
| * Displaying the video overlay during a playback with | |
| * Kodi on an RPi3 seems to be a great solution with a | |
| * failure rate around 50%. | |
| * | |
| * Removing 1 from the FIFO full level however | |
| * seems to completely remove that issue. | |
| */ | |
| if (vc4->gen == VC4_GEN_4) | |
| return fifo_len_bytes - 3 * HVS_FIFO_LATENCY_PIX - 1; | |
| return fifo_len_bytes - 3 * HVS_FIFO_LATENCY_PIX; | |
| } | |
| } | |
| static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc, | |
| u32 format) | |
| { | |
| u32 level = vc4_get_fifo_full_level(vc4_crtc, format); | |
| u32 ret = 0; | |
| ret |= VC4_SET_FIELD((level >> 6), | |
| PV5_CONTROL_FIFO_LEVEL_HIGH); | |
| return ret | VC4_SET_FIELD(level & 0x3f, | |
| PV_CONTROL_FIFO_LEVEL); | |
| } | |
| /* | |
| * Returns the encoder attached to the CRTC. | |
| * | |
| * VC4 can only scan out to one encoder at a time, while the DRM core | |
| * allows drivers to push pixels to more than one encoder from the | |
| * same CRTC. | |
| */ | |
| struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc, | |
| struct drm_crtc_state *state) | |
| { | |
| struct drm_encoder *encoder; | |
| WARN_ON(hweight32(state->encoder_mask) > 1); | |
| drm_for_each_encoder_mask(encoder, crtc->dev, state->encoder_mask) | |
| return encoder; | |
| return NULL; | |
| } | |
| static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct drm_device *dev = crtc->dev; | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return; | |
| /* The PV needs to be disabled before it can be flushed */ | |
| CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) & ~PV_CONTROL_EN); | |
| CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_FIFO_CLR); | |
| drm_dev_exit(idx); | |
| } | |
| static void vc4_crtc_config_pv(struct drm_crtc *crtc, struct drm_encoder *encoder, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder); | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc); | |
| struct drm_crtc_state *crtc_state = crtc->state; | |
| struct drm_display_mode *mode = &crtc_state->adjusted_mode; | |
| bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE; | |
| bool is_hdmi = vc4_encoder->type == VC4_ENCODER_TYPE_HDMI0 || | |
| vc4_encoder->type == VC4_ENCODER_TYPE_HDMI1; | |
| u32 pixel_rep = ((mode->flags & DRM_MODE_FLAG_DBLCLK) && !is_hdmi) ? 2 : 1; | |
| bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 || | |
| vc4_encoder->type == VC4_ENCODER_TYPE_DSI1); | |
| bool is_dsi1 = vc4_encoder->type == VC4_ENCODER_TYPE_DSI1; | |
| bool is_vec = vc4_encoder->type == VC4_ENCODER_TYPE_VEC; | |
| u32 format = is_dsi1 ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24; | |
| u8 ppc = pv_data->pixels_per_clock; | |
| u16 vert_bp = mode->crtc_vtotal - mode->crtc_vsync_end; | |
| u16 vert_sync = mode->crtc_vsync_end - mode->crtc_vsync_start; | |
| u16 vert_fp = mode->crtc_vsync_start - mode->crtc_vdisplay; | |
| bool debug_dump_regs = false; | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return; | |
| if (debug_dump_regs) { | |
| struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev); | |
| dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs before:\n", | |
| drm_crtc_index(crtc)); | |
| drm_print_regset32(&p, &vc4_crtc->regset); | |
| } | |
| vc4_crtc_pixelvalve_reset(crtc); | |
| CRTC_WRITE(PV_HORZA, | |
| VC4_SET_FIELD((mode->htotal - mode->hsync_end) * pixel_rep / ppc, | |
| PV_HORZA_HBP) | | |
| VC4_SET_FIELD((mode->hsync_end - mode->hsync_start) * pixel_rep / ppc, | |
| PV_HORZA_HSYNC)); | |
| CRTC_WRITE(PV_HORZB, | |
| VC4_SET_FIELD((mode->hsync_start - mode->hdisplay) * pixel_rep / ppc, | |
| PV_HORZB_HFP) | | |
| VC4_SET_FIELD(mode->hdisplay * pixel_rep / ppc, | |
| PV_HORZB_HACTIVE)); | |
| if (interlace) { | |
| bool odd_field_first = false; | |
| u32 field_delay = mode->htotal * pixel_rep / (2 * ppc); | |
| u16 vert_bp_even = vert_bp; | |
| u16 vert_fp_even = vert_fp; | |
| if (is_vec) { | |
| /* VEC (composite output) */ | |
| ++field_delay; | |
| if (mode->htotal == 858) { | |
| /* 525-line mode (NTSC or PAL-M) */ | |
| odd_field_first = true; | |
| } | |
| } | |
| if (odd_field_first) | |
| ++vert_fp_even; | |
| else | |
| ++vert_bp; | |
| CRTC_WRITE(PV_VERTA_EVEN, | |
| VC4_SET_FIELD(vert_bp_even, PV_VERTA_VBP) | | |
| VC4_SET_FIELD(vert_sync, PV_VERTA_VSYNC)); | |
| CRTC_WRITE(PV_VERTB_EVEN, | |
| VC4_SET_FIELD(vert_fp_even, PV_VERTB_VFP) | | |
| VC4_SET_FIELD(mode->crtc_vdisplay, PV_VERTB_VACTIVE)); | |
| /* We set up first field even mode for HDMI and VEC's PAL. | |
| * For NTSC, we need first field odd. | |
| */ | |
| CRTC_WRITE(PV_V_CONTROL, | |
| PV_VCONTROL_CONTINUOUS | | |
| (vc4->gen >= VC4_GEN_6_C ? PV_VCONTROL_ODD_TIMING : 0) | | |
| (is_dsi ? PV_VCONTROL_DSI : 0) | | |
| PV_VCONTROL_INTERLACE | | |
| (odd_field_first | |
| ? PV_VCONTROL_ODD_FIRST | |
| : VC4_SET_FIELD(field_delay, | |
| PV_VCONTROL_ODD_DELAY))); | |
| CRTC_WRITE(PV_VSYNCD_EVEN, | |
| (odd_field_first ? field_delay : 0)); | |
| } else { | |
| CRTC_WRITE(PV_V_CONTROL, | |
| PV_VCONTROL_CONTINUOUS | | |
| (vc4->gen >= VC4_GEN_6_C ? PV_VCONTROL_ODD_TIMING : 0) | | |
| (is_dsi ? PV_VCONTROL_DSI : 0)); | |
| CRTC_WRITE(PV_VSYNCD_EVEN, 0); | |
| } | |
| CRTC_WRITE(PV_VERTA, | |
| VC4_SET_FIELD(vert_bp, PV_VERTA_VBP) | | |
| VC4_SET_FIELD(vert_sync, PV_VERTA_VSYNC)); | |
| CRTC_WRITE(PV_VERTB, | |
| VC4_SET_FIELD(vert_fp, PV_VERTB_VFP) | | |
| VC4_SET_FIELD(mode->crtc_vdisplay, PV_VERTB_VACTIVE)); | |
| if (is_dsi) | |
| CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep); | |
| if (vc4->gen >= VC4_GEN_5) | |
| CRTC_WRITE(PV_MUX_CFG, | |
| VC4_SET_FIELD(PV_MUX_CFG_RGB_PIXEL_MUX_MODE_NO_SWAP, | |
| PV_MUX_CFG_RGB_PIXEL_MUX_MODE)); | |
| if (vc4->gen >= VC4_GEN_6_C) | |
| CRTC_WRITE(PV_PIPE_INIT_CTRL, | |
| VC4_SET_FIELD(1, PV_PIPE_INIT_CTRL_PV_INIT_WIDTH) | | |
| VC4_SET_FIELD(1, PV_PIPE_INIT_CTRL_PV_INIT_IDLE) | | |
| PV_PIPE_INIT_CTRL_PV_INIT_EN); | |
| CRTC_WRITE(PV_CONTROL, PV_CONTROL_FIFO_CLR | | |
| vc4_crtc_get_fifo_full_level_bits(vc4_crtc, format) | | |
| VC4_SET_FIELD(format, PV_CONTROL_FORMAT) | | |
| VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) | | |
| PV_CONTROL_CLR_AT_START | | |
| PV_CONTROL_TRIGGER_UNDERFLOW | | |
| PV_CONTROL_WAIT_HSTART | | |
| VC4_SET_FIELD(vc4_encoder->clock_select, | |
| PV_CONTROL_CLK_SELECT)); | |
| if (debug_dump_regs) { | |
| struct drm_printer p = drm_info_printer(&vc4_crtc->pdev->dev); | |
| dev_info(&vc4_crtc->pdev->dev, "CRTC %d regs after:\n", | |
| drm_crtc_index(crtc)); | |
| drm_print_regset32(&p, &vc4_crtc->regset); | |
| } | |
| drm_dev_exit(idx); | |
| } | |
| static void require_hvs_enabled(struct drm_device *dev) | |
| { | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| if (vc4->gen >= VC4_GEN_6_C) | |
| WARN_ON_ONCE(!(HVS_READ(SCALER6_CONTROL) & SCALER6_CONTROL_HVS_EN)); | |
| else | |
| WARN_ON_ONCE(!(HVS_READ(SCALER_DISPCTRL) & SCALER_DISPCTRL_ENABLE)); | |
| } | |
| static int vc4_crtc_disable(struct drm_crtc *crtc, | |
| struct drm_encoder *encoder, | |
| struct drm_atomic_commit *state, | |
| unsigned int channel) | |
| { | |
| struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder); | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| int idx, ret; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return -ENODEV; | |
| CRTC_WRITE(PV_V_CONTROL, | |
| CRTC_READ(PV_V_CONTROL) & ~PV_VCONTROL_VIDEN); | |
| ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1); | |
| WARN_ONCE(ret, "Timeout waiting for !PV_VCONTROL_VIDEN\n"); | |
| /* | |
| * This delay is needed to avoid to get a pixel stuck in an | |
| * unflushable FIFO between the pixelvalve and the HDMI | |
| * controllers on the BCM2711. | |
| * | |
| * Timing is fairly sensitive here, so mdelay is the safest | |
| * approach. | |
| * | |
| * If it was to be reworked, the stuck pixel happens on a | |
| * BCM2711 when changing mode with a good probability, so a | |
| * script that changes mode on a regular basis should trigger | |
| * the bug after less than 10 attempts. It manifests itself with | |
| * every pixels being shifted by one to the right, and thus the | |
| * last pixel of a line actually being displayed as the first | |
| * pixel on the next line. | |
| */ | |
| mdelay(20); | |
| if (vc4_encoder && vc4_encoder->post_crtc_disable) | |
| vc4_encoder->post_crtc_disable(encoder, state); | |
| vc4_crtc_pixelvalve_reset(crtc); | |
| vc4_hvs_stop_channel(vc4->hvs, channel); | |
| if (vc4_encoder && vc4_encoder->post_crtc_powerdown) | |
| vc4_encoder->post_crtc_powerdown(encoder, state); | |
| drm_dev_exit(idx); | |
| return 0; | |
| } | |
| int vc4_crtc_disable_at_boot(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *drm = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(drm); | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| enum vc4_encoder_type encoder_type; | |
| const struct vc4_pv_data *pv_data; | |
| struct drm_encoder *encoder; | |
| struct vc4_hdmi *vc4_hdmi; | |
| unsigned encoder_sel; | |
| int channel; | |
| int ret; | |
| if (!(of_device_is_compatible(vc4_crtc->pdev->dev.of_node, | |
| "brcm,bcm2711-pixelvalve2") || | |
| of_device_is_compatible(vc4_crtc->pdev->dev.of_node, | |
| "brcm,bcm2711-pixelvalve4") || | |
| of_device_is_compatible(vc4_crtc->pdev->dev.of_node, | |
| "brcm,bcm2712-pixelvalve0") || | |
| of_device_is_compatible(vc4_crtc->pdev->dev.of_node, | |
| "brcm,bcm2712-pixelvalve1"))) | |
| return 0; | |
| if (!(CRTC_READ(PV_CONTROL) & PV_CONTROL_EN)) | |
| return 0; | |
| if (!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN)) | |
| return 0; | |
| channel = vc4_hvs_get_fifo_from_output(vc4->hvs, vc4_crtc->data->hvs_output); | |
| if (channel < 0) | |
| return 0; | |
| encoder_sel = VC4_GET_FIELD(CRTC_READ(PV_CONTROL), PV_CONTROL_CLK_SELECT); | |
| if (WARN_ON(encoder_sel != 0)) | |
| return 0; | |
| pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc); | |
| encoder_type = pv_data->encoder_types[encoder_sel]; | |
| encoder = vc4_find_encoder_by_type(drm, encoder_type); | |
| if (WARN_ON(!encoder)) | |
| return 0; | |
| vc4_hdmi = encoder_to_vc4_hdmi(encoder); | |
| ret = pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev); | |
| if (ret) | |
| return ret; | |
| ret = vc4_crtc_disable(crtc, encoder, NULL, channel); | |
| if (ret) | |
| return ret; | |
| /* | |
| * post_crtc_powerdown will have called pm_runtime_put, so we | |
| * don't need it here otherwise we'll get the reference counting | |
| * wrong. | |
| */ | |
| return 0; | |
| } | |
| void vc4_crtc_send_vblank(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| unsigned long flags; | |
| if (!crtc->state || !crtc->state->event) | |
| return; | |
| spin_lock_irqsave(&dev->event_lock, flags); | |
| drm_crtc_send_vblank_event(crtc, crtc->state->event); | |
| crtc->state->event = NULL; | |
| spin_unlock_irqrestore(&dev->event_lock, flags); | |
| } | |
| static void vc4_crtc_atomic_disable(struct drm_crtc *crtc, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct drm_crtc_state *old_state = drm_atomic_get_old_crtc_state(state, | |
| crtc); | |
| struct vc4_crtc_state *old_vc4_state = to_vc4_crtc_state(old_state); | |
| struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc, old_state); | |
| struct drm_device *dev = crtc->dev; | |
| drm_dbg(dev, "Disabling CRTC %s (%u) connected to Encoder %s (%u)", | |
| crtc->name, crtc->base.id, encoder->name, encoder->base.id); | |
| require_hvs_enabled(dev); | |
| /* Disable vblank irq handling before crtc is disabled. */ | |
| drm_crtc_vblank_off(crtc); | |
| vc4_crtc_disable(crtc, encoder, state, old_vc4_state->assigned_channel); | |
| /* | |
| * Make sure we issue a vblank event after disabling the CRTC if | |
| * someone was waiting it. | |
| */ | |
| vc4_crtc_send_vblank(crtc); | |
| } | |
| static void vc4_crtc_atomic_enable(struct drm_crtc *crtc, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct drm_crtc_state *new_state = drm_atomic_get_new_crtc_state(state, | |
| crtc); | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc, new_state); | |
| struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder); | |
| int idx; | |
| drm_dbg(dev, "Enabling CRTC %s (%u) connected to Encoder %s (%u)", | |
| crtc->name, crtc->base.id, encoder->name, encoder->base.id); | |
| if (!drm_dev_enter(dev, &idx)) | |
| return; | |
| require_hvs_enabled(dev); | |
| /* Enable vblank irq handling before crtc is started otherwise | |
| * drm_crtc_get_vblank() fails in vc4_crtc_update_dlist(). | |
| */ | |
| drm_crtc_vblank_on(crtc); | |
| vc4_hvs_atomic_enable(crtc, state); | |
| if (vc4_encoder->pre_crtc_configure) | |
| vc4_encoder->pre_crtc_configure(encoder, state); | |
| vc4_crtc_config_pv(crtc, encoder, state); | |
| CRTC_WRITE(PV_CONTROL, CRTC_READ(PV_CONTROL) | PV_CONTROL_EN); | |
| if (vc4_encoder->pre_crtc_enable) | |
| vc4_encoder->pre_crtc_enable(encoder, state); | |
| /* When feeding the transposer block the pixelvalve is unneeded and | |
| * should not be enabled. | |
| */ | |
| CRTC_WRITE(PV_V_CONTROL, | |
| CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN); | |
| if (vc4_encoder->post_crtc_enable) | |
| vc4_encoder->post_crtc_enable(encoder, state); | |
| drm_dev_exit(idx); | |
| } | |
| static enum drm_mode_status vc4_crtc_mode_valid(struct drm_crtc *crtc, | |
| const struct drm_display_mode *mode) | |
| { | |
| /* Do not allow doublescan modes from user space */ | |
| if (mode->flags & DRM_MODE_FLAG_DBLSCAN) { | |
| DRM_DEBUG_KMS("[CRTC:%d] Doublescan mode rejected.\n", | |
| crtc->base.id); | |
| return MODE_NO_DBLESCAN; | |
| } | |
| return MODE_OK; | |
| } | |
| void vc4_crtc_get_margins(struct drm_crtc_state *state, | |
| unsigned int *left, unsigned int *right, | |
| unsigned int *top, unsigned int *bottom) | |
| { | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state); | |
| struct drm_connector_state *conn_state; | |
| struct drm_connector *conn; | |
| int i; | |
| *left = vc4_state->margins.left; | |
| *right = vc4_state->margins.right; | |
| *top = vc4_state->margins.top; | |
| *bottom = vc4_state->margins.bottom; | |
| /* We have to interate over all new connector states because | |
| * vc4_crtc_get_margins() might be called before | |
| * vc4_crtc_atomic_check() which means margins info in vc4_crtc_state | |
| * might be outdated. | |
| */ | |
| for_each_new_connector_in_state(state->state, conn, conn_state, i) { | |
| if (conn_state->crtc != state->crtc) | |
| continue; | |
| *left = conn_state->tv.margins.left; | |
| *right = conn_state->tv.margins.right; | |
| *top = conn_state->tv.margins.top; | |
| *bottom = conn_state->tv.margins.bottom; | |
| break; | |
| } | |
| } | |
| int vc4_crtc_atomic_check(struct drm_crtc *crtc, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, | |
| crtc); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc_state); | |
| struct drm_connector *conn; | |
| struct drm_connector_state *conn_state; | |
| struct drm_encoder *encoder; | |
| int ret, i; | |
| ret = vc4_hvs_atomic_check(crtc, state); | |
| if (ret) | |
| return ret; | |
| encoder = vc4_get_crtc_encoder(crtc, crtc_state); | |
| if (encoder) { | |
| const struct drm_display_mode *mode = &crtc_state->adjusted_mode; | |
| struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder); | |
| if (vc4_encoder->type == VC4_ENCODER_TYPE_HDMI0) { | |
| vc4_state->hvs_load = max(mode->clock * mode->hdisplay / mode->htotal + 8000, | |
| mode->clock * 9 / 10) * 1000; | |
| } else { | |
| vc4_state->hvs_load = mode->clock * 1000; | |
| } | |
| } | |
| for_each_new_connector_in_state(state, conn, conn_state, | |
| i) { | |
| if (conn_state->crtc != crtc) | |
| continue; | |
| if (memcmp(&vc4_state->margins, &conn_state->tv.margins, | |
| sizeof(vc4_state->margins))) { | |
| memcpy(&vc4_state->margins, &conn_state->tv.margins, | |
| sizeof(vc4_state->margins)); | |
| /* | |
| * Need to force the dlist entries for all planes to be | |
| * updated so that the dest rectangles are changed. | |
| */ | |
| crtc_state->zpos_changed = true; | |
| } | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int vc4_enable_vblank(struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct drm_device *dev = crtc->dev; | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return -ENODEV; | |
| CRTC_WRITE(PV_INTEN, PV_INT_VFP_START); | |
| drm_dev_exit(idx); | |
| return 0; | |
| } | |
| static void vc4_disable_vblank(struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| struct drm_device *dev = crtc->dev; | |
| int idx; | |
| if (!drm_dev_enter(dev, &idx)) | |
| return; | |
| CRTC_WRITE(PV_INTEN, 0); | |
| drm_dev_exit(idx); | |
| } | |
| static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc) | |
| { | |
| struct drm_crtc *crtc = &vc4_crtc->base; | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct vc4_hvs *hvs = vc4->hvs; | |
| unsigned int current_dlist; | |
| u32 chan = vc4_crtc->current_hvs_channel; | |
| unsigned long flags; | |
| spin_lock_irqsave(&dev->event_lock, flags); | |
| spin_lock(&vc4_crtc->irq_lock); | |
| if (vc4->gen >= VC4_GEN_6_C) | |
| current_dlist = VC4_GET_FIELD(HVS_READ(SCALER6_DISPX_DL(chan)), | |
| SCALER6_DISPX_DL_LACT); | |
| else | |
| current_dlist = HVS_READ(SCALER_DISPLACTX(chan)); | |
| if (vc4_crtc->event && | |
| (vc4_crtc->current_dlist == current_dlist || vc4_crtc->feeds_txp)) { | |
| drm_crtc_send_vblank_event(crtc, vc4_crtc->event); | |
| vc4_crtc->event = NULL; | |
| drm_crtc_vblank_put(crtc); | |
| /* Wait for the page flip to unmask the underrun to ensure that | |
| * the display list was updated by the hardware. Before that | |
| * happens, the HVS will be using the previous display list with | |
| * the CRTC and encoder already reconfigured, leading to | |
| * underruns. This can be seen when reconfiguring the CRTC. | |
| */ | |
| if (vc4->gen < VC4_GEN_6_C) | |
| vc4_hvs_unmask_underrun(hvs, chan); | |
| } | |
| spin_unlock(&vc4_crtc->irq_lock); | |
| spin_unlock_irqrestore(&dev->event_lock, flags); | |
| } | |
| void vc4_crtc_handle_vblank(struct vc4_crtc *crtc) | |
| { | |
| crtc->t_vblank = ktime_get(); | |
| drm_crtc_handle_vblank(&crtc->base); | |
| vc4_crtc_handle_page_flip(crtc); | |
| } | |
| static irqreturn_t vc4_crtc_irq_handler(int irq, void *data) | |
| { | |
| struct vc4_crtc *vc4_crtc = data; | |
| u32 stat = CRTC_READ(PV_INTSTAT); | |
| irqreturn_t ret = IRQ_NONE; | |
| if (stat & PV_INT_VFP_START) { | |
| CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START); | |
| vc4_crtc_handle_vblank(vc4_crtc); | |
| ret = IRQ_HANDLED; | |
| } | |
| return ret; | |
| } | |
| struct vc4_async_flip_state { | |
| struct drm_crtc *crtc; | |
| struct drm_framebuffer *fb; | |
| struct drm_framebuffer *old_fb; | |
| struct drm_pending_vblank_event *event; | |
| struct dma_fence_cb cb; | |
| }; | |
| /* Called when the V3D execution for the BO being flipped to is done, so that | |
| * we can actually update the plane's address to point to it. | |
| */ | |
| static void | |
| vc4_async_page_flip_complete(struct vc4_async_flip_state *flip_state) | |
| { | |
| struct drm_crtc *crtc = flip_state->crtc; | |
| struct drm_device *dev = crtc->dev; | |
| struct drm_plane *plane = crtc->primary; | |
| vc4_plane_async_set_fb(plane, flip_state->fb); | |
| if (flip_state->event) { | |
| unsigned long flags; | |
| spin_lock_irqsave(&dev->event_lock, flags); | |
| drm_crtc_send_vblank_event(crtc, flip_state->event); | |
| spin_unlock_irqrestore(&dev->event_lock, flags); | |
| } | |
| drm_crtc_vblank_put(crtc); | |
| drm_framebuffer_put(flip_state->fb); | |
| if (flip_state->old_fb) | |
| drm_framebuffer_put(flip_state->old_fb); | |
| kfree(flip_state); | |
| } | |
| static void vc4_async_page_flip_complete_with_cleanup(struct dma_fence *fence, | |
| struct dma_fence_cb *cb) | |
| { | |
| struct vc4_async_flip_state *flip_state = | |
| container_of(cb, struct vc4_async_flip_state, cb); | |
| struct vc4_bo *bo = NULL; | |
| if (flip_state->old_fb) { | |
| struct drm_gem_dma_object *dma_bo = | |
| drm_fb_dma_get_gem_obj(flip_state->old_fb, 0); | |
| bo = to_vc4_bo(&dma_bo->base); | |
| } | |
| vc4_async_page_flip_complete(flip_state); | |
| dma_fence_put(fence); | |
| /* | |
| * Decrement the BO usecnt in order to keep the inc/dec | |
| * calls balanced when the planes are updated through | |
| * the async update path. | |
| * | |
| * FIXME: we should move to generic async-page-flip when | |
| * it's available, so that we can get rid of this | |
| * hand-made cleanup_fb() logic. | |
| */ | |
| if (bo) | |
| vc4_bo_dec_usecnt(bo); | |
| } | |
| static void vc4_async_page_flip_fence_complete(struct dma_fence *fence, | |
| struct dma_fence_cb *cb) | |
| { | |
| struct vc4_async_flip_state *flip_state = | |
| container_of(cb, struct vc4_async_flip_state, cb); | |
| vc4_async_page_flip_complete(flip_state); | |
| dma_fence_put(fence); | |
| } | |
| static int vc4_async_set_fence_cb(struct drm_device *dev, | |
| struct vc4_async_flip_state *flip_state) | |
| { | |
| struct drm_framebuffer *fb = flip_state->fb; | |
| struct drm_gem_dma_object *dma_bo = drm_fb_dma_get_gem_obj(fb, 0); | |
| dma_fence_func_t async_page_flip_complete_function; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct dma_fence *fence; | |
| int ret; | |
| if (vc4->gen == VC4_GEN_4) | |
| async_page_flip_complete_function = vc4_async_page_flip_complete_with_cleanup; | |
| else | |
| async_page_flip_complete_function = vc4_async_page_flip_fence_complete; | |
| ret = dma_resv_get_singleton(dma_bo->base.resv, DMA_RESV_USAGE_READ, &fence); | |
| if (ret) | |
| return ret; | |
| /* If there's no fence, complete the page flip immediately */ | |
| if (!fence) { | |
| async_page_flip_complete_function(fence, &flip_state->cb); | |
| return 0; | |
| } | |
| /* If the fence has already been completed, complete the page flip */ | |
| if (dma_fence_add_callback(fence, &flip_state->cb, | |
| async_page_flip_complete_function)) | |
| async_page_flip_complete_function(fence, &flip_state->cb); | |
| return 0; | |
| } | |
| static int | |
| vc4_async_page_flip_common(struct drm_crtc *crtc, | |
| struct drm_framebuffer *fb, | |
| struct drm_pending_vblank_event *event, | |
| uint32_t flags) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct drm_plane *plane = crtc->primary; | |
| struct vc4_async_flip_state *flip_state; | |
| flip_state = kzalloc_obj(*flip_state); | |
| if (!flip_state) | |
| return -ENOMEM; | |
| drm_framebuffer_get(fb); | |
| flip_state->fb = fb; | |
| flip_state->crtc = crtc; | |
| flip_state->event = event; | |
| /* Save the current FB before it's replaced by the new one in | |
| * drm_atomic_set_fb_for_plane(). We'll need the old FB in | |
| * vc4_async_page_flip_complete() to decrement the BO usecnt and keep | |
| * it consistent. | |
| * FIXME: we should move to generic async-page-flip when it's | |
| * available, so that we can get rid of this hand-made cleanup_fb() | |
| * logic. | |
| */ | |
| flip_state->old_fb = plane->state->fb; | |
| if (flip_state->old_fb) | |
| drm_framebuffer_get(flip_state->old_fb); | |
| WARN_ON(drm_crtc_vblank_get(crtc) != 0); | |
| /* Immediately update the plane's legacy fb pointer, so that later | |
| * modeset prep sees the state that will be present when the semaphore | |
| * is released. | |
| */ | |
| drm_atomic_set_fb_for_plane(plane->state, fb); | |
| vc4_async_set_fence_cb(dev, flip_state); | |
| /* Driver takes ownership of state on successful async commit. */ | |
| return 0; | |
| } | |
| /* Implements async (non-vblank-synced) page flips. | |
| * | |
| * The page flip ioctl needs to return immediately, so we grab the | |
| * modeset semaphore on the pipe, and queue the address update for | |
| * when V3D is done with the BO being flipped to. | |
| */ | |
| static int vc4_async_page_flip(struct drm_crtc *crtc, | |
| struct drm_framebuffer *fb, | |
| struct drm_pending_vblank_event *event, | |
| uint32_t flags) | |
| { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| struct drm_gem_dma_object *dma_bo = drm_fb_dma_get_gem_obj(fb, 0); | |
| struct vc4_bo *bo = to_vc4_bo(&dma_bo->base); | |
| int ret; | |
| if (WARN_ON_ONCE(vc4->gen > VC4_GEN_4)) | |
| return -ENODEV; | |
| /* | |
| * Increment the BO usecnt here, so that we never end up with an | |
| * unbalanced number of vc4_bo_{dec,inc}_usecnt() calls when the | |
| * plane is later updated through the non-async path. | |
| * | |
| * FIXME: we should move to generic async-page-flip when | |
| * it's available, so that we can get rid of this | |
| * hand-made prepare_fb() logic. | |
| */ | |
| ret = vc4_bo_inc_usecnt(bo); | |
| if (ret) | |
| return ret; | |
| ret = vc4_async_page_flip_common(crtc, fb, event, flags); | |
| if (ret) { | |
| vc4_bo_dec_usecnt(bo); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int vc5_async_page_flip(struct drm_crtc *crtc, | |
| struct drm_framebuffer *fb, | |
| struct drm_pending_vblank_event *event, | |
| uint32_t flags) | |
| { | |
| return vc4_async_page_flip_common(crtc, fb, event, flags); | |
| } | |
| int vc4_page_flip(struct drm_crtc *crtc, | |
| struct drm_framebuffer *fb, | |
| struct drm_pending_vblank_event *event, | |
| uint32_t flags, | |
| struct drm_modeset_acquire_ctx *ctx) | |
| { | |
| if (flags & DRM_MODE_PAGE_FLIP_ASYNC) { | |
| struct drm_device *dev = crtc->dev; | |
| struct vc4_dev *vc4 = to_vc4_dev(dev); | |
| if (vc4->gen > VC4_GEN_4) | |
| return vc5_async_page_flip(crtc, fb, event, flags); | |
| else | |
| return vc4_async_page_flip(crtc, fb, event, flags); | |
| } else { | |
| return drm_atomic_helper_page_flip(crtc, fb, event, flags, ctx); | |
| } | |
| } | |
| struct drm_crtc_state *vc4_crtc_duplicate_state(struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc_state *vc4_state, *old_vc4_state; | |
| vc4_state = kzalloc_obj(*vc4_state); | |
| if (!vc4_state) | |
| return NULL; | |
| old_vc4_state = to_vc4_crtc_state(crtc->state); | |
| vc4_state->margins = old_vc4_state->margins; | |
| vc4_state->assigned_channel = old_vc4_state->assigned_channel; | |
| __drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base); | |
| return &vc4_state->base; | |
| } | |
| void vc4_crtc_destroy_state(struct drm_crtc *crtc, | |
| struct drm_crtc_state *state) | |
| { | |
| struct vc4_dev *vc4 = to_vc4_dev(crtc->dev); | |
| struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state); | |
| if (drm_mm_node_allocated(&vc4_state->mm)) { | |
| unsigned long flags; | |
| spin_lock_irqsave(&vc4->hvs->mm_lock, flags); | |
| drm_mm_remove_node(&vc4_state->mm); | |
| spin_unlock_irqrestore(&vc4->hvs->mm_lock, flags); | |
| } | |
| drm_atomic_helper_crtc_destroy_state(crtc, state); | |
| } | |
| void vc4_crtc_reset(struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc_state *vc4_crtc_state; | |
| if (crtc->state) | |
| vc4_crtc_destroy_state(crtc, crtc->state); | |
| vc4_crtc_state = kzalloc_obj(*vc4_crtc_state); | |
| if (!vc4_crtc_state) { | |
| crtc->state = NULL; | |
| return; | |
| } | |
| vc4_crtc_state->assigned_channel = VC4_HVS_CHANNEL_DISABLED; | |
| __drm_atomic_helper_crtc_reset(crtc, &vc4_crtc_state->base); | |
| } | |
| int vc4_crtc_late_register(struct drm_crtc *crtc) | |
| { | |
| struct drm_device *drm = crtc->dev; | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| const struct vc4_crtc_data *crtc_data = vc4_crtc_to_vc4_crtc_data(vc4_crtc); | |
| vc4_debugfs_add_regset32(drm, crtc_data->debugfs_name, | |
| &vc4_crtc->regset); | |
| return 0; | |
| } | |
| static const struct drm_crtc_funcs vc4_crtc_funcs = { | |
| .set_config = drm_atomic_helper_set_config, | |
| .page_flip = vc4_page_flip, | |
| .set_property = NULL, | |
| .cursor_set = NULL, /* handled by drm_mode_cursor_universal */ | |
| .cursor_move = NULL, /* handled by drm_mode_cursor_universal */ | |
| .reset = vc4_crtc_reset, | |
| .atomic_duplicate_state = vc4_crtc_duplicate_state, | |
| .atomic_destroy_state = vc4_crtc_destroy_state, | |
| .enable_vblank = vc4_enable_vblank, | |
| .disable_vblank = vc4_disable_vblank, | |
| .get_vblank_timestamp = drm_crtc_vblank_helper_get_vblank_timestamp, | |
| .late_register = vc4_crtc_late_register, | |
| }; | |
| static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = { | |
| .mode_valid = vc4_crtc_mode_valid, | |
| .atomic_check = vc4_crtc_atomic_check, | |
| .atomic_begin = vc4_hvs_atomic_begin, | |
| .atomic_flush = vc4_hvs_atomic_flush, | |
| .atomic_enable = vc4_crtc_atomic_enable, | |
| .atomic_disable = vc4_crtc_atomic_disable, | |
| .get_scanout_position = vc4_crtc_get_scanout_position, | |
| }; | |
| const struct vc4_pv_data bcm2835_pv0_data = { | |
| .base = { | |
| .name = "pixelvalve-0", | |
| .debugfs_name = "crtc0_regs", | |
| .hvs_available_channels = BIT(0), | |
| .hvs_output = 0, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI0, | |
| [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_DPI, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2835_pv1_data = { | |
| .base = { | |
| .name = "pixelvalve-1", | |
| .debugfs_name = "crtc1_regs", | |
| .hvs_available_channels = BIT(2), | |
| .hvs_output = 2, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [PV_CONTROL_CLK_SELECT_DSI] = VC4_ENCODER_TYPE_DSI1, | |
| [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_SMI, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2835_pv2_data = { | |
| .base = { | |
| .name = "pixelvalve-2", | |
| .debugfs_name = "crtc2_regs", | |
| .hvs_available_channels = BIT(1), | |
| .hvs_output = 1, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI] = VC4_ENCODER_TYPE_HDMI0, | |
| [PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2711_pv0_data = { | |
| .base = { | |
| .name = "pixelvalve-0", | |
| .debugfs_name = "crtc0_regs", | |
| .hvs_available_channels = BIT(0), | |
| .hvs_output = 0, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_DSI0, | |
| [1] = VC4_ENCODER_TYPE_DPI, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2711_pv1_data = { | |
| .base = { | |
| .name = "pixelvalve-1", | |
| .debugfs_name = "crtc1_regs", | |
| .hvs_available_channels = BIT(0) | BIT(1) | BIT(2), | |
| .hvs_output = 3, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_DSI1, | |
| [1] = VC4_ENCODER_TYPE_SMI, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2711_pv2_data = { | |
| .base = { | |
| .name = "pixelvalve-2", | |
| .debugfs_name = "crtc2_regs", | |
| .hvs_available_channels = BIT(0) | BIT(1) | BIT(2), | |
| .hvs_output = 4, | |
| }, | |
| .fifo_depth = 256, | |
| .pixels_per_clock = 2, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_HDMI0, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2711_pv3_data = { | |
| .base = { | |
| .name = "pixelvalve-3", | |
| .debugfs_name = "crtc3_regs", | |
| .hvs_available_channels = BIT(1), | |
| .hvs_output = 1, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [PV_CONTROL_CLK_SELECT_VEC] = VC4_ENCODER_TYPE_VEC, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2711_pv4_data = { | |
| .base = { | |
| .name = "pixelvalve-4", | |
| .debugfs_name = "crtc4_regs", | |
| .hvs_available_channels = BIT(0) | BIT(1) | BIT(2), | |
| .hvs_output = 5, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 2, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_HDMI1, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2712_pv0_data = { | |
| .base = { | |
| .debugfs_name = "crtc0_regs", | |
| .hvs_available_channels = BIT(0), | |
| .hvs_output = 0, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_HDMI0, | |
| }, | |
| }; | |
| const struct vc4_pv_data bcm2712_pv1_data = { | |
| .base = { | |
| .debugfs_name = "crtc1_regs", | |
| .hvs_available_channels = BIT(1), | |
| .hvs_output = 1, | |
| }, | |
| .fifo_depth = 64, | |
| .pixels_per_clock = 1, | |
| .encoder_types = { | |
| [0] = VC4_ENCODER_TYPE_HDMI1, | |
| }, | |
| }; | |
| static const struct of_device_id vc4_crtc_dt_match[] = { | |
| { .compatible = "brcm,bcm2835-pixelvalve0", .data = &bcm2835_pv0_data }, | |
| { .compatible = "brcm,bcm2835-pixelvalve1", .data = &bcm2835_pv1_data }, | |
| { .compatible = "brcm,bcm2835-pixelvalve2", .data = &bcm2835_pv2_data }, | |
| { .compatible = "brcm,bcm2711-pixelvalve0", .data = &bcm2711_pv0_data }, | |
| { .compatible = "brcm,bcm2711-pixelvalve1", .data = &bcm2711_pv1_data }, | |
| { .compatible = "brcm,bcm2711-pixelvalve2", .data = &bcm2711_pv2_data }, | |
| { .compatible = "brcm,bcm2711-pixelvalve3", .data = &bcm2711_pv3_data }, | |
| { .compatible = "brcm,bcm2711-pixelvalve4", .data = &bcm2711_pv4_data }, | |
| { .compatible = "brcm,bcm2712-pixelvalve0", .data = &bcm2712_pv0_data }, | |
| { .compatible = "brcm,bcm2712-pixelvalve1", .data = &bcm2712_pv1_data }, | |
| {} | |
| }; | |
| static void vc4_set_crtc_possible_masks(struct drm_device *drm, | |
| struct drm_crtc *crtc) | |
| { | |
| struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); | |
| const struct vc4_pv_data *pv_data = vc4_crtc_to_vc4_pv_data(vc4_crtc); | |
| const enum vc4_encoder_type *encoder_types = pv_data->encoder_types; | |
| struct drm_encoder *encoder; | |
| drm_for_each_encoder(encoder, drm) { | |
| struct vc4_encoder *vc4_encoder; | |
| int i; | |
| if (encoder->encoder_type == DRM_MODE_ENCODER_VIRTUAL) | |
| continue; | |
| vc4_encoder = to_vc4_encoder(encoder); | |
| for (i = 0; i < ARRAY_SIZE(pv_data->encoder_types); i++) { | |
| if (vc4_encoder->type == encoder_types[i]) { | |
| vc4_encoder->clock_select = i; | |
| encoder->possible_crtcs |= drm_crtc_mask(crtc); | |
| break; | |
| } | |
| } | |
| } | |
| } | |
| /** | |
| * __vc4_crtc_init - Initializes a CRTC | |
| * @drm: DRM Device | |
| * @pdev: CRTC Platform Device | |
| * @vc4_crtc: CRTC Object to Initialize | |
| * @data: Configuration data associated with this CRTC | |
| * @primary_plane: Primary plane for CRTC | |
| * @crtc_funcs: Callbacks for the new CRTC | |
| * @crtc_helper_funcs: Helper Callbacks for the new CRTC | |
| * @feeds_txp: Is this CRTC connected to the TXP? | |
| * | |
| * Initializes our private CRTC structure. This function is mostly | |
| * relevant for KUnit testing, all other users should use | |
| * vc4_crtc_init() instead. | |
| * | |
| * Returns: | |
| * 0 on success, a negative error code on failure. | |
| */ | |
| int __vc4_crtc_init(struct drm_device *drm, | |
| struct platform_device *pdev, | |
| struct vc4_crtc *vc4_crtc, | |
| const struct vc4_crtc_data *data, | |
| struct drm_plane *primary_plane, | |
| const struct drm_crtc_funcs *crtc_funcs, | |
| const struct drm_crtc_helper_funcs *crtc_helper_funcs, | |
| bool feeds_txp) | |
| { | |
| struct vc4_dev *vc4 = to_vc4_dev(drm); | |
| struct drm_crtc *crtc = &vc4_crtc->base; | |
| unsigned int i; | |
| int ret; | |
| vc4_crtc->data = data; | |
| vc4_crtc->pdev = pdev; | |
| vc4_crtc->feeds_txp = feeds_txp; | |
| spin_lock_init(&vc4_crtc->irq_lock); | |
| ret = drmm_crtc_init_with_planes(drm, crtc, primary_plane, NULL, | |
| crtc_funcs, data->name); | |
| if (ret) | |
| return ret; | |
| drm_crtc_helper_add(crtc, crtc_helper_funcs); | |
| if (vc4->gen == VC4_GEN_4) { | |
| drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r)); | |
| drm_crtc_enable_color_mgmt(crtc, 0, false, crtc->gamma_size); | |
| /* We support CTM, but only for one CRTC at a time. It's therefore | |
| * implemented as private driver state in vc4_kms, not here. | |
| */ | |
| drm_crtc_enable_color_mgmt(crtc, 0, true, crtc->gamma_size); | |
| } | |
| for (i = 0; i < crtc->gamma_size; i++) { | |
| vc4_crtc->lut_r[i] = i; | |
| vc4_crtc->lut_g[i] = i; | |
| vc4_crtc->lut_b[i] = i; | |
| } | |
| return 0; | |
| } | |
| int vc4_crtc_init(struct drm_device *drm, struct platform_device *pdev, | |
| struct vc4_crtc *vc4_crtc, | |
| const struct vc4_crtc_data *data, | |
| const struct drm_crtc_funcs *crtc_funcs, | |
| const struct drm_crtc_helper_funcs *crtc_helper_funcs, | |
| bool feeds_txp) | |
| { | |
| struct drm_plane *primary_plane; | |
| /* For now, we create just the primary and the legacy cursor | |
| * planes. We should be able to stack more planes on easily, | |
| * but to do that we would need to compute the bandwidth | |
| * requirement of the plane configuration, and reject ones | |
| * that will take too much. | |
| */ | |
| primary_plane = vc4_plane_init(drm, DRM_PLANE_TYPE_PRIMARY, 0); | |
| if (IS_ERR(primary_plane)) { | |
| dev_err(drm->dev, "failed to construct primary plane\n"); | |
| return PTR_ERR(primary_plane); | |
| } | |
| return __vc4_crtc_init(drm, pdev, vc4_crtc, data, primary_plane, | |
| crtc_funcs, crtc_helper_funcs, feeds_txp); | |
| } | |
| static int vc4_crtc_bind(struct device *dev, struct device *master, void *data) | |
| { | |
| struct platform_device *pdev = to_platform_device(dev); | |
| struct drm_device *drm = dev_get_drvdata(master); | |
| const struct vc4_pv_data *pv_data; | |
| struct vc4_crtc *vc4_crtc; | |
| struct drm_crtc *crtc; | |
| int ret; | |
| vc4_crtc = drmm_kzalloc(drm, sizeof(*vc4_crtc), GFP_KERNEL); | |
| if (!vc4_crtc) | |
| return -ENOMEM; | |
| crtc = &vc4_crtc->base; | |
| pv_data = of_device_get_match_data(dev); | |
| if (!pv_data) | |
| return -ENODEV; | |
| vc4_crtc->regs = vc4_ioremap_regs(pdev, 0); | |
| if (IS_ERR(vc4_crtc->regs)) | |
| return PTR_ERR(vc4_crtc->regs); | |
| vc4_crtc->regset.base = vc4_crtc->regs; | |
| vc4_crtc->regset.regs = crtc_regs; | |
| vc4_crtc->regset.nregs = ARRAY_SIZE(crtc_regs); | |
| ret = vc4_crtc_init(drm, pdev, vc4_crtc, &pv_data->base, | |
| &vc4_crtc_funcs, &vc4_crtc_helper_funcs, | |
| false); | |
| if (ret) | |
| return ret; | |
| vc4_set_crtc_possible_masks(drm, crtc); | |
| CRTC_WRITE(PV_INTEN, 0); | |
| CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START); | |
| ret = devm_request_irq(dev, platform_get_irq(pdev, 0), | |
| vc4_crtc_irq_handler, | |
| IRQF_SHARED, | |
| "vc4 crtc", vc4_crtc); | |
| if (ret) | |
| return ret; | |
| platform_set_drvdata(pdev, vc4_crtc); | |
| return 0; | |
| } | |
| static void vc4_crtc_unbind(struct device *dev, struct device *master, | |
| void *data) | |
| { | |
| struct platform_device *pdev = to_platform_device(dev); | |
| struct vc4_crtc *vc4_crtc = dev_get_drvdata(dev); | |
| CRTC_WRITE(PV_INTEN, 0); | |
| platform_set_drvdata(pdev, NULL); | |
| } | |
| static const struct component_ops vc4_crtc_ops = { | |
| .bind = vc4_crtc_bind, | |
| .unbind = vc4_crtc_unbind, | |
| }; | |
| static int vc4_crtc_dev_probe(struct platform_device *pdev) | |
| { | |
| return component_add(&pdev->dev, &vc4_crtc_ops); | |
| } | |
| static void vc4_crtc_dev_remove(struct platform_device *pdev) | |
| { | |
| component_del(&pdev->dev, &vc4_crtc_ops); | |
| } | |
| struct platform_driver vc4_crtc_driver = { | |
| .probe = vc4_crtc_dev_probe, | |
| .remove = vc4_crtc_dev_remove, | |
| .driver = { | |
| .name = "vc4_crtc", | |
| .of_match_table = vc4_crtc_dt_match, | |
| }, | |
| }; |