| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2018-2019, Bridge Systems BV | |
| * Copyright (C) 2018-2019, Bootlin | |
| * Copyright (C) 2017, Free Electrons | |
| * | |
| * This file based on panel-ilitek-ili9881c.c | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/device.h> | |
| #include <linux/err.h> | |
| #include <linux/errno.h> | |
| #include <linux/kernel.h> | |
| #include <linux/media-bus-format.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <drm/drm_connector.h> | |
| #include <drm/drm_mipi_dsi.h> | |
| #include <drm/drm_modes.h> | |
| #include <drm/drm_panel.h> | |
| struct rb070d30_panel { | |
| struct drm_panel panel; | |
| struct mipi_dsi_device *dsi; | |
| struct regulator *supply; | |
| struct { | |
| struct gpio_desc *power; | |
| struct gpio_desc *reset; | |
| struct gpio_desc *updn; | |
| struct gpio_desc *shlr; | |
| } gpios; | |
| }; | |
| static inline struct rb070d30_panel *panel_to_rb070d30_panel(struct drm_panel *panel) | |
| { | |
| return container_of(panel, struct rb070d30_panel, panel); | |
| } | |
| static int rb070d30_panel_prepare(struct drm_panel *panel) | |
| { | |
| struct rb070d30_panel *ctx = panel_to_rb070d30_panel(panel); | |
| int ret; | |
| ret = regulator_enable(ctx->supply); | |
| if (ret < 0) { | |
| dev_err(&ctx->dsi->dev, "Failed to enable supply: %d\n", ret); | |
| return ret; | |
| } | |
| msleep(20); | |
| gpiod_set_value_cansleep(ctx->gpios.power, 1); | |
| msleep(20); | |
| gpiod_set_value_cansleep(ctx->gpios.reset, 1); | |
| msleep(20); | |
| return 0; | |
| } | |
| static int rb070d30_panel_unprepare(struct drm_panel *panel) | |
| { | |
| struct rb070d30_panel *ctx = panel_to_rb070d30_panel(panel); | |
| gpiod_set_value_cansleep(ctx->gpios.reset, 0); | |
| gpiod_set_value_cansleep(ctx->gpios.power, 0); | |
| regulator_disable(ctx->supply); | |
| return 0; | |
| } | |
| static int rb070d30_panel_enable(struct drm_panel *panel) | |
| { | |
| struct rb070d30_panel *ctx = panel_to_rb070d30_panel(panel); | |
| return mipi_dsi_dcs_exit_sleep_mode(ctx->dsi); | |
| } | |
| static int rb070d30_panel_disable(struct drm_panel *panel) | |
| { | |
| struct rb070d30_panel *ctx = panel_to_rb070d30_panel(panel); | |
| return mipi_dsi_dcs_enter_sleep_mode(ctx->dsi); | |
| } | |
| /* Default timings */ | |
| static const struct drm_display_mode default_mode = { | |
| .clock = 51206, | |
| .hdisplay = 1024, | |
| .hsync_start = 1024 + 160, | |
| .hsync_end = 1024 + 160 + 80, | |
| .htotal = 1024 + 160 + 80 + 80, | |
| .vdisplay = 600, | |
| .vsync_start = 600 + 12, | |
| .vsync_end = 600 + 12 + 10, | |
| .vtotal = 600 + 12 + 10 + 13, | |
| .width_mm = 154, | |
| .height_mm = 85, | |
| }; | |
| static int rb070d30_panel_get_modes(struct drm_panel *panel, | |
| struct drm_connector *connector) | |
| { | |
| struct rb070d30_panel *ctx = panel_to_rb070d30_panel(panel); | |
| struct drm_display_mode *mode; | |
| static const u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24; | |
| mode = drm_mode_duplicate(connector->dev, &default_mode); | |
| if (!mode) { | |
| dev_err(&ctx->dsi->dev, "Failed to add mode " DRM_MODE_FMT "\n", | |
| DRM_MODE_ARG(&default_mode)); | |
| return -EINVAL; | |
| } | |
| drm_mode_set_name(mode); | |
| mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; | |
| drm_mode_probed_add(connector, mode); | |
| connector->display_info.bpc = 8; | |
| connector->display_info.width_mm = mode->width_mm; | |
| connector->display_info.height_mm = mode->height_mm; | |
| drm_display_info_set_bus_formats(&connector->display_info, | |
| &bus_format, 1); | |
| return 1; | |
| } | |
| static const struct drm_panel_funcs rb070d30_panel_funcs = { | |
| .get_modes = rb070d30_panel_get_modes, | |
| .prepare = rb070d30_panel_prepare, | |
| .enable = rb070d30_panel_enable, | |
| .disable = rb070d30_panel_disable, | |
| .unprepare = rb070d30_panel_unprepare, | |
| }; | |
| static int rb070d30_panel_dsi_probe(struct mipi_dsi_device *dsi) | |
| { | |
| struct rb070d30_panel *ctx; | |
| int ret; | |
| ctx = devm_drm_panel_alloc(&dsi->dev, struct rb070d30_panel, panel, | |
| &rb070d30_panel_funcs, | |
| DRM_MODE_CONNECTOR_DSI); | |
| if (IS_ERR(ctx)) | |
| return PTR_ERR(ctx); | |
| ctx->supply = devm_regulator_get(&dsi->dev, "vcc-lcd"); | |
| if (IS_ERR(ctx->supply)) | |
| return PTR_ERR(ctx->supply); | |
| mipi_dsi_set_drvdata(dsi, ctx); | |
| ctx->dsi = dsi; | |
| ctx->gpios.reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW); | |
| if (IS_ERR(ctx->gpios.reset)) { | |
| dev_err(&dsi->dev, "Couldn't get our reset GPIO\n"); | |
| return PTR_ERR(ctx->gpios.reset); | |
| } | |
| ctx->gpios.power = devm_gpiod_get(&dsi->dev, "power", GPIOD_OUT_LOW); | |
| if (IS_ERR(ctx->gpios.power)) { | |
| dev_err(&dsi->dev, "Couldn't get our power GPIO\n"); | |
| return PTR_ERR(ctx->gpios.power); | |
| } | |
| /* | |
| * We don't change the state of that GPIO later on but we need | |
| * to force it into a low state. | |
| */ | |
| ctx->gpios.updn = devm_gpiod_get(&dsi->dev, "updn", GPIOD_OUT_LOW); | |
| if (IS_ERR(ctx->gpios.updn)) { | |
| dev_err(&dsi->dev, "Couldn't get our updn GPIO\n"); | |
| return PTR_ERR(ctx->gpios.updn); | |
| } | |
| /* | |
| * We don't change the state of that GPIO later on but we need | |
| * to force it into a low state. | |
| */ | |
| ctx->gpios.shlr = devm_gpiod_get(&dsi->dev, "shlr", GPIOD_OUT_LOW); | |
| if (IS_ERR(ctx->gpios.shlr)) { | |
| dev_err(&dsi->dev, "Couldn't get our shlr GPIO\n"); | |
| return PTR_ERR(ctx->gpios.shlr); | |
| } | |
| ret = drm_panel_of_backlight(&ctx->panel); | |
| if (ret) | |
| return ret; | |
| drm_panel_add(&ctx->panel); | |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM; | |
| dsi->format = MIPI_DSI_FMT_RGB888; | |
| dsi->lanes = 4; | |
| ret = mipi_dsi_attach(dsi); | |
| if (ret < 0) { | |
| drm_panel_remove(&ctx->panel); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static void rb070d30_panel_dsi_remove(struct mipi_dsi_device *dsi) | |
| { | |
| struct rb070d30_panel *ctx = mipi_dsi_get_drvdata(dsi); | |
| mipi_dsi_detach(dsi); | |
| drm_panel_remove(&ctx->panel); | |
| } | |
| static const struct of_device_id rb070d30_panel_of_match[] = { | |
| { .compatible = "ronbo,rb070d30" }, | |
| { /* sentinel */ }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, rb070d30_panel_of_match); | |
| static struct mipi_dsi_driver rb070d30_panel_driver = { | |
| .probe = rb070d30_panel_dsi_probe, | |
| .remove = rb070d30_panel_dsi_remove, | |
| .driver = { | |
| .name = "panel-ronbo-rb070d30", | |
| .of_match_table = rb070d30_panel_of_match, | |
| }, | |
| }; | |
| module_mipi_dsi_driver(rb070d30_panel_driver); | |
| MODULE_AUTHOR("Boris Brezillon <boris.brezillon@bootlin.com>"); | |
| MODULE_AUTHOR("Konstantin Sudakov <k.sudakov@integrasources.com>"); | |
| MODULE_DESCRIPTION("Ronbo RB070D30 Panel Driver"); | |
| MODULE_LICENSE("GPL"); |