| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright (C) 2012 Texas Instruments | |
| * Author: Rob Clark <robdclark@gmail.com> | |
| */ | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/hdmi.h> | |
| #include <linux/i2c.h> | |
| #include <linux/module.h> | |
| #include <linux/platform_data/tda9950.h> | |
| #include <linux/irq.h> | |
| #include <sound/asoundef.h> | |
| #include <sound/hdmi-codec.h> | |
| #include <drm/drm_atomic_helper.h> | |
| #include <drm/drm_bridge.h> | |
| #include <drm/drm_edid.h> | |
| #include <drm/drm_of.h> | |
| #include <drm/drm_print.h> | |
| #include <drm/drm_probe_helper.h> | |
| #include <drm/drm_simple_kms_helper.h> | |
| #include <media/cec-notifier.h> | |
| #include <dt-bindings/display/tda998x.h> | |
| #define DBG(fmt, ...) DRM_DEBUG(fmt"\n", ##__VA_ARGS__) | |
| enum { | |
| AUDIO_ROUTE_I2S, | |
| AUDIO_ROUTE_SPDIF, | |
| AUDIO_ROUTE_NUM | |
| }; | |
| struct tda998x_audio_route { | |
| u8 ena_aclk; | |
| u8 mux_ap; | |
| u8 aip_clksel; | |
| }; | |
| struct tda998x_audio_settings { | |
| const struct tda998x_audio_route *route; | |
| struct hdmi_audio_infoframe cea; | |
| unsigned int sample_rate; | |
| u8 status[5]; | |
| u8 ena_ap; | |
| u8 i2s_format; | |
| u8 cts_n; | |
| }; | |
| struct tda998x_priv { | |
| struct i2c_client *cec; | |
| struct i2c_client *hdmi; | |
| struct mutex mutex; | |
| u16 rev; | |
| u8 cec_addr; | |
| u8 current_page; | |
| bool is_on; | |
| bool supports_infoframes; | |
| bool sink_has_audio; | |
| enum hdmi_quantization_range rgb_quant_range; | |
| u8 vip_cntrl_0; | |
| u8 vip_cntrl_1; | |
| u8 vip_cntrl_2; | |
| unsigned long tmds_clock; | |
| struct tda998x_audio_settings audio; | |
| struct platform_device *audio_pdev; | |
| struct mutex audio_mutex; | |
| struct mutex edid_mutex; | |
| wait_queue_head_t wq_edid; | |
| volatile int wq_edid_wait; | |
| struct work_struct detect_work; | |
| struct timer_list edid_delay_timer; | |
| wait_queue_head_t edid_delay_waitq; | |
| bool edid_delay_active; | |
| struct drm_encoder encoder; | |
| struct drm_bridge bridge; | |
| struct drm_connector connector; | |
| u8 audio_port_enable[AUDIO_ROUTE_NUM]; | |
| struct tda9950_glue cec_glue; | |
| struct gpio_desc *calib; | |
| struct cec_notifier *cec_notify; | |
| }; | |
| #define conn_to_tda998x_priv(x) \ | |
| container_of(x, struct tda998x_priv, connector) | |
| #define enc_to_tda998x_priv(x) \ | |
| container_of(x, struct tda998x_priv, encoder) | |
| #define bridge_to_tda998x_priv(x) \ | |
| container_of(x, struct tda998x_priv, bridge) | |
| /* The TDA9988 series of devices use a paged register scheme.. to simplify | |
| * things we encode the page # in upper bits of the register #. To read/ | |
| * write a given register, we need to make sure CURPAGE register is set | |
| * appropriately. Which implies reads/writes are not atomic. Fun! | |
| */ | |
| #define REG(page, addr) (((page) << 8) | (addr)) | |
| #define REG2ADDR(reg) ((reg) & 0xff) | |
| #define REG2PAGE(reg) (((reg) >> 8) & 0xff) | |
| #define REG_CURPAGE 0xff /* write */ | |
| /* Page 00h: General Control */ | |
| #define REG_VERSION_LSB REG(0x00, 0x00) /* read */ | |
| #define REG_MAIN_CNTRL0 REG(0x00, 0x01) /* read/write */ | |
| # define MAIN_CNTRL0_SR (1 << 0) | |
| # define MAIN_CNTRL0_DECS (1 << 1) | |
| # define MAIN_CNTRL0_DEHS (1 << 2) | |
| # define MAIN_CNTRL0_CECS (1 << 3) | |
| # define MAIN_CNTRL0_CEHS (1 << 4) | |
| # define MAIN_CNTRL0_SCALER (1 << 7) | |
| #define REG_VERSION_MSB REG(0x00, 0x02) /* read */ | |
| #define REG_SOFTRESET REG(0x00, 0x0a) /* write */ | |
| # define SOFTRESET_AUDIO (1 << 0) | |
| # define SOFTRESET_I2C_MASTER (1 << 1) | |
| #define REG_DDC_DISABLE REG(0x00, 0x0b) /* read/write */ | |
| #define REG_CCLK_ON REG(0x00, 0x0c) /* read/write */ | |
| #define REG_I2C_MASTER REG(0x00, 0x0d) /* read/write */ | |
| # define I2C_MASTER_DIS_MM (1 << 0) | |
| # define I2C_MASTER_DIS_FILT (1 << 1) | |
| # define I2C_MASTER_APP_STRT_LAT (1 << 2) | |
| #define REG_FEAT_POWERDOWN REG(0x00, 0x0e) /* read/write */ | |
| # define FEAT_POWERDOWN_PREFILT BIT(0) | |
| # define FEAT_POWERDOWN_CSC BIT(1) | |
| # define FEAT_POWERDOWN_SPDIF (1 << 3) | |
| #define REG_INT_FLAGS_0 REG(0x00, 0x0f) /* read/write */ | |
| #define REG_INT_FLAGS_1 REG(0x00, 0x10) /* read/write */ | |
| #define REG_INT_FLAGS_2 REG(0x00, 0x11) /* read/write */ | |
| # define INT_FLAGS_2_EDID_BLK_RD (1 << 1) | |
| #define REG_ENA_ACLK REG(0x00, 0x16) /* read/write */ | |
| #define REG_ENA_VP_0 REG(0x00, 0x18) /* read/write */ | |
| #define REG_ENA_VP_1 REG(0x00, 0x19) /* read/write */ | |
| #define REG_ENA_VP_2 REG(0x00, 0x1a) /* read/write */ | |
| #define REG_ENA_AP REG(0x00, 0x1e) /* read/write */ | |
| #define REG_VIP_CNTRL_0 REG(0x00, 0x20) /* write */ | |
| # define VIP_CNTRL_0_MIRR_A (1 << 7) | |
| # define VIP_CNTRL_0_SWAP_A(x) (((x) & 7) << 4) | |
| # define VIP_CNTRL_0_MIRR_B (1 << 3) | |
| # define VIP_CNTRL_0_SWAP_B(x) (((x) & 7) << 0) | |
| #define REG_VIP_CNTRL_1 REG(0x00, 0x21) /* write */ | |
| # define VIP_CNTRL_1_MIRR_C (1 << 7) | |
| # define VIP_CNTRL_1_SWAP_C(x) (((x) & 7) << 4) | |
| # define VIP_CNTRL_1_MIRR_D (1 << 3) | |
| # define VIP_CNTRL_1_SWAP_D(x) (((x) & 7) << 0) | |
| #define REG_VIP_CNTRL_2 REG(0x00, 0x22) /* write */ | |
| # define VIP_CNTRL_2_MIRR_E (1 << 7) | |
| # define VIP_CNTRL_2_SWAP_E(x) (((x) & 7) << 4) | |
| # define VIP_CNTRL_2_MIRR_F (1 << 3) | |
| # define VIP_CNTRL_2_SWAP_F(x) (((x) & 7) << 0) | |
| #define REG_VIP_CNTRL_3 REG(0x00, 0x23) /* write */ | |
| # define VIP_CNTRL_3_X_TGL (1 << 0) | |
| # define VIP_CNTRL_3_H_TGL (1 << 1) | |
| # define VIP_CNTRL_3_V_TGL (1 << 2) | |
| # define VIP_CNTRL_3_EMB (1 << 3) | |
| # define VIP_CNTRL_3_SYNC_DE (1 << 4) | |
| # define VIP_CNTRL_3_SYNC_HS (1 << 5) | |
| # define VIP_CNTRL_3_DE_INT (1 << 6) | |
| # define VIP_CNTRL_3_EDGE (1 << 7) | |
| #define REG_VIP_CNTRL_4 REG(0x00, 0x24) /* write */ | |
| # define VIP_CNTRL_4_BLC(x) (((x) & 3) << 0) | |
| # define VIP_CNTRL_4_BLANKIT(x) (((x) & 3) << 2) | |
| # define VIP_CNTRL_4_CCIR656 (1 << 4) | |
| # define VIP_CNTRL_4_656_ALT (1 << 5) | |
| # define VIP_CNTRL_4_TST_656 (1 << 6) | |
| # define VIP_CNTRL_4_TST_PAT (1 << 7) | |
| #define REG_VIP_CNTRL_5 REG(0x00, 0x25) /* write */ | |
| # define VIP_CNTRL_5_CKCASE (1 << 0) | |
| # define VIP_CNTRL_5_SP_CNT(x) (((x) & 3) << 1) | |
| #define REG_MUX_AP REG(0x00, 0x26) /* read/write */ | |
| # define MUX_AP_SELECT_I2S 0x64 | |
| # define MUX_AP_SELECT_SPDIF 0x40 | |
| #define REG_MUX_VP_VIP_OUT REG(0x00, 0x27) /* read/write */ | |
| #define REG_MAT_CONTRL REG(0x00, 0x80) /* write */ | |
| # define MAT_CONTRL_MAT_SC(x) (((x) & 3) << 0) | |
| # define MAT_CONTRL_MAT_BP (1 << 2) | |
| #define REG_VIDFORMAT REG(0x00, 0xa0) /* write */ | |
| #define REG_REFPIX_MSB REG(0x00, 0xa1) /* write */ | |
| #define REG_REFPIX_LSB REG(0x00, 0xa2) /* write */ | |
| #define REG_REFLINE_MSB REG(0x00, 0xa3) /* write */ | |
| #define REG_REFLINE_LSB REG(0x00, 0xa4) /* write */ | |
| #define REG_NPIX_MSB REG(0x00, 0xa5) /* write */ | |
| #define REG_NPIX_LSB REG(0x00, 0xa6) /* write */ | |
| #define REG_NLINE_MSB REG(0x00, 0xa7) /* write */ | |
| #define REG_NLINE_LSB REG(0x00, 0xa8) /* write */ | |
| #define REG_VS_LINE_STRT_1_MSB REG(0x00, 0xa9) /* write */ | |
| #define REG_VS_LINE_STRT_1_LSB REG(0x00, 0xaa) /* write */ | |
| #define REG_VS_PIX_STRT_1_MSB REG(0x00, 0xab) /* write */ | |
| #define REG_VS_PIX_STRT_1_LSB REG(0x00, 0xac) /* write */ | |
| #define REG_VS_LINE_END_1_MSB REG(0x00, 0xad) /* write */ | |
| #define REG_VS_LINE_END_1_LSB REG(0x00, 0xae) /* write */ | |
| #define REG_VS_PIX_END_1_MSB REG(0x00, 0xaf) /* write */ | |
| #define REG_VS_PIX_END_1_LSB REG(0x00, 0xb0) /* write */ | |
| #define REG_VS_LINE_STRT_2_MSB REG(0x00, 0xb1) /* write */ | |
| #define REG_VS_LINE_STRT_2_LSB REG(0x00, 0xb2) /* write */ | |
| #define REG_VS_PIX_STRT_2_MSB REG(0x00, 0xb3) /* write */ | |
| #define REG_VS_PIX_STRT_2_LSB REG(0x00, 0xb4) /* write */ | |
| #define REG_VS_LINE_END_2_MSB REG(0x00, 0xb5) /* write */ | |
| #define REG_VS_LINE_END_2_LSB REG(0x00, 0xb6) /* write */ | |
| #define REG_VS_PIX_END_2_MSB REG(0x00, 0xb7) /* write */ | |
| #define REG_VS_PIX_END_2_LSB REG(0x00, 0xb8) /* write */ | |
| #define REG_HS_PIX_START_MSB REG(0x00, 0xb9) /* write */ | |
| #define REG_HS_PIX_START_LSB REG(0x00, 0xba) /* write */ | |
| #define REG_HS_PIX_STOP_MSB REG(0x00, 0xbb) /* write */ | |
| #define REG_HS_PIX_STOP_LSB REG(0x00, 0xbc) /* write */ | |
| #define REG_VWIN_START_1_MSB REG(0x00, 0xbd) /* write */ | |
| #define REG_VWIN_START_1_LSB REG(0x00, 0xbe) /* write */ | |
| #define REG_VWIN_END_1_MSB REG(0x00, 0xbf) /* write */ | |
| #define REG_VWIN_END_1_LSB REG(0x00, 0xc0) /* write */ | |
| #define REG_VWIN_START_2_MSB REG(0x00, 0xc1) /* write */ | |
| #define REG_VWIN_START_2_LSB REG(0x00, 0xc2) /* write */ | |
| #define REG_VWIN_END_2_MSB REG(0x00, 0xc3) /* write */ | |
| #define REG_VWIN_END_2_LSB REG(0x00, 0xc4) /* write */ | |
| #define REG_DE_START_MSB REG(0x00, 0xc5) /* write */ | |
| #define REG_DE_START_LSB REG(0x00, 0xc6) /* write */ | |
| #define REG_DE_STOP_MSB REG(0x00, 0xc7) /* write */ | |
| #define REG_DE_STOP_LSB REG(0x00, 0xc8) /* write */ | |
| #define REG_TBG_CNTRL_0 REG(0x00, 0xca) /* write */ | |
| # define TBG_CNTRL_0_TOP_TGL (1 << 0) | |
| # define TBG_CNTRL_0_TOP_SEL (1 << 1) | |
| # define TBG_CNTRL_0_DE_EXT (1 << 2) | |
| # define TBG_CNTRL_0_TOP_EXT (1 << 3) | |
| # define TBG_CNTRL_0_FRAME_DIS (1 << 5) | |
| # define TBG_CNTRL_0_SYNC_MTHD (1 << 6) | |
| # define TBG_CNTRL_0_SYNC_ONCE (1 << 7) | |
| #define REG_TBG_CNTRL_1 REG(0x00, 0xcb) /* write */ | |
| # define TBG_CNTRL_1_H_TGL (1 << 0) | |
| # define TBG_CNTRL_1_V_TGL (1 << 1) | |
| # define TBG_CNTRL_1_TGL_EN (1 << 2) | |
| # define TBG_CNTRL_1_X_EXT (1 << 3) | |
| # define TBG_CNTRL_1_H_EXT (1 << 4) | |
| # define TBG_CNTRL_1_V_EXT (1 << 5) | |
| # define TBG_CNTRL_1_DWIN_DIS (1 << 6) | |
| #define REG_ENABLE_SPACE REG(0x00, 0xd6) /* write */ | |
| #define REG_HVF_CNTRL_0 REG(0x00, 0xe4) /* write */ | |
| # define HVF_CNTRL_0_SM (1 << 7) | |
| # define HVF_CNTRL_0_RWB (1 << 6) | |
| # define HVF_CNTRL_0_PREFIL(x) (((x) & 3) << 2) | |
| # define HVF_CNTRL_0_INTPOL(x) (((x) & 3) << 0) | |
| #define REG_HVF_CNTRL_1 REG(0x00, 0xe5) /* write */ | |
| # define HVF_CNTRL_1_FOR (1 << 0) | |
| # define HVF_CNTRL_1_YUVBLK (1 << 1) | |
| # define HVF_CNTRL_1_VQR(x) (((x) & 3) << 2) | |
| # define HVF_CNTRL_1_PAD(x) (((x) & 3) << 4) | |
| # define HVF_CNTRL_1_SEMI_PLANAR (1 << 6) | |
| #define REG_RPT_CNTRL REG(0x00, 0xf0) /* write */ | |
| # define RPT_CNTRL_REPEAT(x) ((x) & 15) | |
| #define REG_I2S_FORMAT REG(0x00, 0xfc) /* read/write */ | |
| # define I2S_FORMAT_PHILIPS (0 << 0) | |
| # define I2S_FORMAT_LEFT_J (2 << 0) | |
| # define I2S_FORMAT_RIGHT_J (3 << 0) | |
| #define REG_AIP_CLKSEL REG(0x00, 0xfd) /* write */ | |
| # define AIP_CLKSEL_AIP_SPDIF (0 << 3) | |
| # define AIP_CLKSEL_AIP_I2S (1 << 3) | |
| # define AIP_CLKSEL_FS_ACLK (0 << 0) | |
| # define AIP_CLKSEL_FS_MCLK (1 << 0) | |
| # define AIP_CLKSEL_FS_FS64SPDIF (2 << 0) | |
| /* Page 02h: PLL settings */ | |
| #define REG_PLL_SERIAL_1 REG(0x02, 0x00) /* read/write */ | |
| # define PLL_SERIAL_1_SRL_FDN (1 << 0) | |
| # define PLL_SERIAL_1_SRL_IZ(x) (((x) & 3) << 1) | |
| # define PLL_SERIAL_1_SRL_MAN_IZ (1 << 6) | |
| #define REG_PLL_SERIAL_2 REG(0x02, 0x01) /* read/write */ | |
| # define PLL_SERIAL_2_SRL_NOSC(x) ((x) << 0) | |
| # define PLL_SERIAL_2_SRL_PR(x) (((x) & 0xf) << 4) | |
| #define REG_PLL_SERIAL_3 REG(0x02, 0x02) /* read/write */ | |
| # define PLL_SERIAL_3_SRL_CCIR (1 << 0) | |
| # define PLL_SERIAL_3_SRL_DE (1 << 2) | |
| # define PLL_SERIAL_3_SRL_PXIN_SEL (1 << 4) | |
| #define REG_SERIALIZER REG(0x02, 0x03) /* read/write */ | |
| #define REG_BUFFER_OUT REG(0x02, 0x04) /* read/write */ | |
| #define REG_PLL_SCG1 REG(0x02, 0x05) /* read/write */ | |
| #define REG_PLL_SCG2 REG(0x02, 0x06) /* read/write */ | |
| #define REG_PLL_SCGN1 REG(0x02, 0x07) /* read/write */ | |
| #define REG_PLL_SCGN2 REG(0x02, 0x08) /* read/write */ | |
| #define REG_PLL_SCGR1 REG(0x02, 0x09) /* read/write */ | |
| #define REG_PLL_SCGR2 REG(0x02, 0x0a) /* read/write */ | |
| #define REG_AUDIO_DIV REG(0x02, 0x0e) /* read/write */ | |
| # define AUDIO_DIV_SERCLK_1 0 | |
| # define AUDIO_DIV_SERCLK_2 1 | |
| # define AUDIO_DIV_SERCLK_4 2 | |
| # define AUDIO_DIV_SERCLK_8 3 | |
| # define AUDIO_DIV_SERCLK_16 4 | |
| # define AUDIO_DIV_SERCLK_32 5 | |
| #define REG_SEL_CLK REG(0x02, 0x11) /* read/write */ | |
| # define SEL_CLK_SEL_CLK1 (1 << 0) | |
| # define SEL_CLK_SEL_VRF_CLK(x) (((x) & 3) << 1) | |
| # define SEL_CLK_ENA_SC_CLK (1 << 3) | |
| #define REG_ANA_GENERAL REG(0x02, 0x12) /* read/write */ | |
| /* Page 09h: EDID Control */ | |
| #define REG_EDID_DATA_0 REG(0x09, 0x00) /* read */ | |
| /* next 127 successive registers are the EDID block */ | |
| #define REG_EDID_CTRL REG(0x09, 0xfa) /* read/write */ | |
| #define REG_DDC_ADDR REG(0x09, 0xfb) /* read/write */ | |
| #define REG_DDC_OFFS REG(0x09, 0xfc) /* read/write */ | |
| #define REG_DDC_SEGM_ADDR REG(0x09, 0xfd) /* read/write */ | |
| #define REG_DDC_SEGM REG(0x09, 0xfe) /* read/write */ | |
| /* Page 10h: information frames and packets */ | |
| #define REG_IF1_HB0 REG(0x10, 0x20) /* read/write */ | |
| #define REG_IF2_HB0 REG(0x10, 0x40) /* read/write */ | |
| #define REG_IF3_HB0 REG(0x10, 0x60) /* read/write */ | |
| #define REG_IF4_HB0 REG(0x10, 0x80) /* read/write */ | |
| #define REG_IF5_HB0 REG(0x10, 0xa0) /* read/write */ | |
| /* Page 11h: audio settings and content info packets */ | |
| #define REG_AIP_CNTRL_0 REG(0x11, 0x00) /* read/write */ | |
| # define AIP_CNTRL_0_RST_FIFO (1 << 0) | |
| # define AIP_CNTRL_0_SWAP (1 << 1) | |
| # define AIP_CNTRL_0_LAYOUT (1 << 2) | |
| # define AIP_CNTRL_0_ACR_MAN (1 << 5) | |
| # define AIP_CNTRL_0_RST_CTS (1 << 6) | |
| #define REG_CA_I2S REG(0x11, 0x01) /* read/write */ | |
| # define CA_I2S_CA_I2S(x) (((x) & 31) << 0) | |
| # define CA_I2S_HBR_CHSTAT (1 << 6) | |
| #define REG_LATENCY_RD REG(0x11, 0x04) /* read/write */ | |
| #define REG_ACR_CTS_0 REG(0x11, 0x05) /* read/write */ | |
| #define REG_ACR_CTS_1 REG(0x11, 0x06) /* read/write */ | |
| #define REG_ACR_CTS_2 REG(0x11, 0x07) /* read/write */ | |
| #define REG_ACR_N_0 REG(0x11, 0x08) /* read/write */ | |
| #define REG_ACR_N_1 REG(0x11, 0x09) /* read/write */ | |
| #define REG_ACR_N_2 REG(0x11, 0x0a) /* read/write */ | |
| #define REG_CTS_N REG(0x11, 0x0c) /* read/write */ | |
| # define CTS_N_K(x) (((x) & 7) << 0) | |
| # define CTS_N_M(x) (((x) & 3) << 4) | |
| #define REG_ENC_CNTRL REG(0x11, 0x0d) /* read/write */ | |
| # define ENC_CNTRL_RST_ENC (1 << 0) | |
| # define ENC_CNTRL_RST_SEL (1 << 1) | |
| # define ENC_CNTRL_CTL_CODE(x) (((x) & 3) << 2) | |
| #define REG_DIP_FLAGS REG(0x11, 0x0e) /* read/write */ | |
| # define DIP_FLAGS_ACR (1 << 0) | |
| # define DIP_FLAGS_GC (1 << 1) | |
| #define REG_DIP_IF_FLAGS REG(0x11, 0x0f) /* read/write */ | |
| # define DIP_IF_FLAGS_IF1 (1 << 1) | |
| # define DIP_IF_FLAGS_IF2 (1 << 2) | |
| # define DIP_IF_FLAGS_IF3 (1 << 3) | |
| # define DIP_IF_FLAGS_IF4 (1 << 4) | |
| # define DIP_IF_FLAGS_IF5 (1 << 5) | |
| #define REG_CH_STAT_B(x) REG(0x11, 0x14 + (x)) /* read/write */ | |
| /* Page 12h: HDCP and OTP */ | |
| #define REG_TX3 REG(0x12, 0x9a) /* read/write */ | |
| #define REG_TX4 REG(0x12, 0x9b) /* read/write */ | |
| # define TX4_PD_RAM (1 << 1) | |
| #define REG_TX33 REG(0x12, 0xb8) /* read/write */ | |
| # define TX33_HDMI (1 << 1) | |
| /* Page 13h: Gamut related metadata packets */ | |
| /* CEC registers: (not paged) | |
| */ | |
| #define REG_CEC_INTSTATUS 0xee /* read */ | |
| # define CEC_INTSTATUS_CEC (1 << 0) | |
| # define CEC_INTSTATUS_HDMI (1 << 1) | |
| #define REG_CEC_CAL_XOSC_CTRL1 0xf2 | |
| # define CEC_CAL_XOSC_CTRL1_ENA_CAL BIT(0) | |
| #define REG_CEC_DES_FREQ2 0xf5 | |
| # define CEC_DES_FREQ2_DIS_AUTOCAL BIT(7) | |
| #define REG_CEC_CLK 0xf6 | |
| # define CEC_CLK_FRO 0x11 | |
| #define REG_CEC_FRO_IM_CLK_CTRL 0xfb /* read/write */ | |
| # define CEC_FRO_IM_CLK_CTRL_GHOST_DIS (1 << 7) | |
| # define CEC_FRO_IM_CLK_CTRL_ENA_OTP (1 << 6) | |
| # define CEC_FRO_IM_CLK_CTRL_IMCLK_SEL (1 << 1) | |
| # define CEC_FRO_IM_CLK_CTRL_FRO_DIV (1 << 0) | |
| #define REG_CEC_RXSHPDINTENA 0xfc /* read/write */ | |
| #define REG_CEC_RXSHPDINT 0xfd /* read */ | |
| # define CEC_RXSHPDINT_RXSENS BIT(0) | |
| # define CEC_RXSHPDINT_HPD BIT(1) | |
| #define REG_CEC_RXSHPDLEV 0xfe /* read */ | |
| # define CEC_RXSHPDLEV_RXSENS (1 << 0) | |
| # define CEC_RXSHPDLEV_HPD (1 << 1) | |
| #define REG_CEC_ENAMODS 0xff /* read/write */ | |
| # define CEC_ENAMODS_EN_CEC_CLK (1 << 7) | |
| # define CEC_ENAMODS_DIS_FRO (1 << 6) | |
| # define CEC_ENAMODS_DIS_CCLK (1 << 5) | |
| # define CEC_ENAMODS_EN_RXSENS (1 << 2) | |
| # define CEC_ENAMODS_EN_HDMI (1 << 1) | |
| # define CEC_ENAMODS_EN_CEC (1 << 0) | |
| /* Device versions: */ | |
| #define TDA9989N2 0x0101 | |
| #define TDA19989 0x0201 | |
| #define TDA19989N2 0x0202 | |
| #define TDA19988 0x0301 | |
| static void | |
| cec_write(struct tda998x_priv *priv, u16 addr, u8 val) | |
| { | |
| u8 buf[] = {addr, val}; | |
| struct i2c_msg msg = { | |
| .addr = priv->cec_addr, | |
| .len = 2, | |
| .buf = buf, | |
| }; | |
| int ret; | |
| ret = i2c_transfer(priv->hdmi->adapter, &msg, 1); | |
| if (ret < 0) | |
| dev_err(&priv->hdmi->dev, "Error %d writing to cec:0x%x\n", | |
| ret, addr); | |
| } | |
| static u8 | |
| cec_read(struct tda998x_priv *priv, u8 addr) | |
| { | |
| u8 val; | |
| struct i2c_msg msg[2] = { | |
| { | |
| .addr = priv->cec_addr, | |
| .len = 1, | |
| .buf = &addr, | |
| }, { | |
| .addr = priv->cec_addr, | |
| .flags = I2C_M_RD, | |
| .len = 1, | |
| .buf = &val, | |
| }, | |
| }; | |
| int ret; | |
| ret = i2c_transfer(priv->hdmi->adapter, msg, ARRAY_SIZE(msg)); | |
| if (ret < 0) { | |
| dev_err(&priv->hdmi->dev, "Error %d reading from cec:0x%x\n", | |
| ret, addr); | |
| val = 0; | |
| } | |
| return val; | |
| } | |
| static void cec_enamods(struct tda998x_priv *priv, u8 mods, bool enable) | |
| { | |
| int val = cec_read(priv, REG_CEC_ENAMODS); | |
| if (val < 0) | |
| return; | |
| if (enable) | |
| val |= mods; | |
| else | |
| val &= ~mods; | |
| cec_write(priv, REG_CEC_ENAMODS, val); | |
| } | |
| static void tda998x_cec_set_calibration(struct tda998x_priv *priv, bool enable) | |
| { | |
| if (enable) { | |
| u8 val; | |
| cec_write(priv, 0xf3, 0xc0); | |
| cec_write(priv, 0xf4, 0xd4); | |
| /* Enable automatic calibration mode */ | |
| val = cec_read(priv, REG_CEC_DES_FREQ2); | |
| val &= ~CEC_DES_FREQ2_DIS_AUTOCAL; | |
| cec_write(priv, REG_CEC_DES_FREQ2, val); | |
| /* Enable free running oscillator */ | |
| cec_write(priv, REG_CEC_CLK, CEC_CLK_FRO); | |
| cec_enamods(priv, CEC_ENAMODS_DIS_FRO, false); | |
| cec_write(priv, REG_CEC_CAL_XOSC_CTRL1, | |
| CEC_CAL_XOSC_CTRL1_ENA_CAL); | |
| } else { | |
| cec_write(priv, REG_CEC_CAL_XOSC_CTRL1, 0); | |
| } | |
| } | |
| /* | |
| * Calibration for the internal oscillator: we need to set calibration mode, | |
| * and then pulse the IRQ line low for a 10ms ± 1% period. | |
| */ | |
| static void tda998x_cec_calibration(struct tda998x_priv *priv) | |
| { | |
| struct gpio_desc *calib = priv->calib; | |
| mutex_lock(&priv->edid_mutex); | |
| if (priv->hdmi->irq > 0) | |
| disable_irq(priv->hdmi->irq); | |
| gpiod_direction_output(calib, 1); | |
| tda998x_cec_set_calibration(priv, true); | |
| local_irq_disable(); | |
| gpiod_set_value(calib, 0); | |
| mdelay(10); | |
| gpiod_set_value(calib, 1); | |
| local_irq_enable(); | |
| tda998x_cec_set_calibration(priv, false); | |
| gpiod_direction_input(calib); | |
| if (priv->hdmi->irq > 0) | |
| enable_irq(priv->hdmi->irq); | |
| mutex_unlock(&priv->edid_mutex); | |
| } | |
| static int tda998x_cec_hook_init(void *data) | |
| { | |
| struct tda998x_priv *priv = data; | |
| struct gpio_desc *calib; | |
| calib = gpiod_get(&priv->hdmi->dev, "nxp,calib", GPIOD_ASIS); | |
| if (IS_ERR(calib)) { | |
| dev_warn(&priv->hdmi->dev, "failed to get calibration gpio: %ld\n", | |
| PTR_ERR(calib)); | |
| return PTR_ERR(calib); | |
| } | |
| priv->calib = calib; | |
| return 0; | |
| } | |
| static void tda998x_cec_hook_exit(void *data) | |
| { | |
| struct tda998x_priv *priv = data; | |
| gpiod_put(priv->calib); | |
| priv->calib = NULL; | |
| } | |
| static int tda998x_cec_hook_open(void *data) | |
| { | |
| struct tda998x_priv *priv = data; | |
| cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, true); | |
| tda998x_cec_calibration(priv); | |
| return 0; | |
| } | |
| static void tda998x_cec_hook_release(void *data) | |
| { | |
| struct tda998x_priv *priv = data; | |
| cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, false); | |
| } | |
| static int | |
| set_page(struct tda998x_priv *priv, u16 reg) | |
| { | |
| if (REG2PAGE(reg) != priv->current_page) { | |
| struct i2c_client *client = priv->hdmi; | |
| u8 buf[] = { | |
| REG_CURPAGE, REG2PAGE(reg) | |
| }; | |
| int ret = i2c_master_send(client, buf, sizeof(buf)); | |
| if (ret < 0) { | |
| dev_err(&client->dev, "%s %04x err %d\n", __func__, | |
| reg, ret); | |
| return ret; | |
| } | |
| priv->current_page = REG2PAGE(reg); | |
| } | |
| return 0; | |
| } | |
| static int | |
| reg_read_range(struct tda998x_priv *priv, u16 reg, char *buf, int cnt) | |
| { | |
| struct i2c_client *client = priv->hdmi; | |
| u8 addr = REG2ADDR(reg); | |
| int ret; | |
| mutex_lock(&priv->mutex); | |
| ret = set_page(priv, reg); | |
| if (ret < 0) | |
| goto out; | |
| ret = i2c_master_send(client, &addr, sizeof(addr)); | |
| if (ret < 0) | |
| goto fail; | |
| ret = i2c_master_recv(client, buf, cnt); | |
| if (ret < 0) | |
| goto fail; | |
| goto out; | |
| fail: | |
| dev_err(&client->dev, "Error %d reading from 0x%x\n", ret, reg); | |
| out: | |
| mutex_unlock(&priv->mutex); | |
| return ret; | |
| } | |
| #define MAX_WRITE_RANGE_BUF 32 | |
| static void | |
| reg_write_range(struct tda998x_priv *priv, u16 reg, u8 *p, int cnt) | |
| { | |
| struct i2c_client *client = priv->hdmi; | |
| /* This is the maximum size of the buffer passed in */ | |
| u8 buf[MAX_WRITE_RANGE_BUF + 1]; | |
| int ret; | |
| if (cnt > MAX_WRITE_RANGE_BUF) { | |
| dev_err(&client->dev, "Fixed write buffer too small (%d)\n", | |
| MAX_WRITE_RANGE_BUF); | |
| return; | |
| } | |
| buf[0] = REG2ADDR(reg); | |
| memcpy(&buf[1], p, cnt); | |
| mutex_lock(&priv->mutex); | |
| ret = set_page(priv, reg); | |
| if (ret < 0) | |
| goto out; | |
| ret = i2c_master_send(client, buf, cnt + 1); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); | |
| out: | |
| mutex_unlock(&priv->mutex); | |
| } | |
| static int | |
| reg_read(struct tda998x_priv *priv, u16 reg) | |
| { | |
| u8 val = 0; | |
| int ret; | |
| ret = reg_read_range(priv, reg, &val, sizeof(val)); | |
| if (ret < 0) | |
| return ret; | |
| return val; | |
| } | |
| static void | |
| reg_write(struct tda998x_priv *priv, u16 reg, u8 val) | |
| { | |
| struct i2c_client *client = priv->hdmi; | |
| u8 buf[] = {REG2ADDR(reg), val}; | |
| int ret; | |
| mutex_lock(&priv->mutex); | |
| ret = set_page(priv, reg); | |
| if (ret < 0) | |
| goto out; | |
| ret = i2c_master_send(client, buf, sizeof(buf)); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); | |
| out: | |
| mutex_unlock(&priv->mutex); | |
| } | |
| static void | |
| reg_write16(struct tda998x_priv *priv, u16 reg, u16 val) | |
| { | |
| struct i2c_client *client = priv->hdmi; | |
| u8 buf[] = {REG2ADDR(reg), val >> 8, val}; | |
| int ret; | |
| mutex_lock(&priv->mutex); | |
| ret = set_page(priv, reg); | |
| if (ret < 0) | |
| goto out; | |
| ret = i2c_master_send(client, buf, sizeof(buf)); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); | |
| out: | |
| mutex_unlock(&priv->mutex); | |
| } | |
| static void | |
| reg_set(struct tda998x_priv *priv, u16 reg, u8 val) | |
| { | |
| int old_val; | |
| old_val = reg_read(priv, reg); | |
| if (old_val >= 0) | |
| reg_write(priv, reg, old_val | val); | |
| } | |
| static void | |
| reg_clear(struct tda998x_priv *priv, u16 reg, u8 val) | |
| { | |
| int old_val; | |
| old_val = reg_read(priv, reg); | |
| if (old_val >= 0) | |
| reg_write(priv, reg, old_val & ~val); | |
| } | |
| static void | |
| tda998x_reset(struct tda998x_priv *priv) | |
| { | |
| /* reset audio and i2c master: */ | |
| reg_write(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER); | |
| msleep(50); | |
| reg_write(priv, REG_SOFTRESET, 0); | |
| msleep(50); | |
| /* reset transmitter: */ | |
| reg_set(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR); | |
| reg_clear(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR); | |
| /* PLL registers common configuration */ | |
| reg_write(priv, REG_PLL_SERIAL_1, 0x00); | |
| reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(1)); | |
| reg_write(priv, REG_PLL_SERIAL_3, 0x00); | |
| reg_write(priv, REG_SERIALIZER, 0x00); | |
| reg_write(priv, REG_BUFFER_OUT, 0x00); | |
| reg_write(priv, REG_PLL_SCG1, 0x00); | |
| reg_write(priv, REG_AUDIO_DIV, AUDIO_DIV_SERCLK_8); | |
| reg_write(priv, REG_SEL_CLK, SEL_CLK_SEL_CLK1 | SEL_CLK_ENA_SC_CLK); | |
| reg_write(priv, REG_PLL_SCGN1, 0xfa); | |
| reg_write(priv, REG_PLL_SCGN2, 0x00); | |
| reg_write(priv, REG_PLL_SCGR1, 0x5b); | |
| reg_write(priv, REG_PLL_SCGR2, 0x00); | |
| reg_write(priv, REG_PLL_SCG2, 0x10); | |
| /* Write the default value MUX register */ | |
| reg_write(priv, REG_MUX_VP_VIP_OUT, 0x24); | |
| } | |
| /* | |
| * The TDA998x has a problem when trying to read the EDID close to a | |
| * HPD assertion: it needs a delay of 100ms to avoid timing out while | |
| * trying to read EDID data. | |
| * | |
| * However, tda998x_connector_get_modes() may be called at any moment | |
| * after tda998x_connector_detect() indicates that we are connected, so | |
| * we need to delay probing modes in tda998x_connector_get_modes() after | |
| * we have seen a HPD inactive->active transition. This code implements | |
| * that delay. | |
| */ | |
| static void tda998x_edid_delay_done(struct timer_list *t) | |
| { | |
| struct tda998x_priv *priv = timer_container_of(priv, t, | |
| edid_delay_timer); | |
| priv->edid_delay_active = false; | |
| wake_up(&priv->edid_delay_waitq); | |
| schedule_work(&priv->detect_work); | |
| } | |
| static void tda998x_edid_delay_start(struct tda998x_priv *priv) | |
| { | |
| priv->edid_delay_active = true; | |
| mod_timer(&priv->edid_delay_timer, jiffies + HZ/10); | |
| } | |
| static int tda998x_edid_delay_wait(struct tda998x_priv *priv) | |
| { | |
| return wait_event_killable(priv->edid_delay_waitq, !priv->edid_delay_active); | |
| } | |
| /* | |
| * We need to run the KMS hotplug event helper outside of our threaded | |
| * interrupt routine as this can call back into our get_modes method, | |
| * which will want to make use of interrupts. | |
| */ | |
| static void tda998x_detect_work(struct work_struct *work) | |
| { | |
| struct tda998x_priv *priv = | |
| container_of(work, struct tda998x_priv, detect_work); | |
| struct drm_device *dev = priv->connector.dev; | |
| if (dev) | |
| drm_kms_helper_hotplug_event(dev); | |
| } | |
| /* | |
| * only 2 interrupts may occur: screen plug/unplug and EDID read | |
| */ | |
| static irqreturn_t tda998x_irq_thread(int irq, void *data) | |
| { | |
| struct tda998x_priv *priv = data; | |
| u8 sta, cec, lvl, flag0, flag1, flag2; | |
| bool handled = false; | |
| sta = cec_read(priv, REG_CEC_INTSTATUS); | |
| if (sta & CEC_INTSTATUS_HDMI) { | |
| cec = cec_read(priv, REG_CEC_RXSHPDINT); | |
| lvl = cec_read(priv, REG_CEC_RXSHPDLEV); | |
| flag0 = reg_read(priv, REG_INT_FLAGS_0); | |
| flag1 = reg_read(priv, REG_INT_FLAGS_1); | |
| flag2 = reg_read(priv, REG_INT_FLAGS_2); | |
| DRM_DEBUG_DRIVER( | |
| "tda irq sta %02x cec %02x lvl %02x f0 %02x f1 %02x f2 %02x\n", | |
| sta, cec, lvl, flag0, flag1, flag2); | |
| if (cec & CEC_RXSHPDINT_HPD) { | |
| if (lvl & CEC_RXSHPDLEV_HPD) { | |
| tda998x_edid_delay_start(priv); | |
| } else { | |
| schedule_work(&priv->detect_work); | |
| cec_notifier_phys_addr_invalidate( | |
| priv->cec_notify); | |
| } | |
| handled = true; | |
| } | |
| if ((flag2 & INT_FLAGS_2_EDID_BLK_RD) && priv->wq_edid_wait) { | |
| priv->wq_edid_wait = 0; | |
| wake_up(&priv->wq_edid); | |
| handled = true; | |
| } | |
| } | |
| return IRQ_RETVAL(handled); | |
| } | |
| static void | |
| tda998x_write_if(struct tda998x_priv *priv, u8 bit, u16 addr, | |
| union hdmi_infoframe *frame) | |
| { | |
| u8 buf[MAX_WRITE_RANGE_BUF]; | |
| ssize_t len; | |
| len = hdmi_infoframe_pack(frame, buf, sizeof(buf)); | |
| if (len < 0) { | |
| dev_err(&priv->hdmi->dev, | |
| "hdmi_infoframe_pack() type=0x%02x failed: %zd\n", | |
| frame->any.type, len); | |
| return; | |
| } | |
| reg_clear(priv, REG_DIP_IF_FLAGS, bit); | |
| reg_write_range(priv, addr, buf, len); | |
| reg_set(priv, REG_DIP_IF_FLAGS, bit); | |
| } | |
| static void tda998x_write_aif(struct tda998x_priv *priv, | |
| const struct hdmi_audio_infoframe *cea) | |
| { | |
| union hdmi_infoframe frame; | |
| frame.audio = *cea; | |
| tda998x_write_if(priv, DIP_IF_FLAGS_IF4, REG_IF4_HB0, &frame); | |
| } | |
| static void | |
| tda998x_write_avi(struct tda998x_priv *priv, const struct drm_display_mode *mode) | |
| { | |
| union hdmi_infoframe frame; | |
| drm_hdmi_avi_infoframe_from_display_mode(&frame.avi, | |
| &priv->connector, mode); | |
| frame.avi.quantization_range = HDMI_QUANTIZATION_RANGE_FULL; | |
| drm_hdmi_avi_infoframe_quant_range(&frame.avi, &priv->connector, mode, | |
| priv->rgb_quant_range); | |
| tda998x_write_if(priv, DIP_IF_FLAGS_IF2, REG_IF2_HB0, &frame); | |
| } | |
| static void tda998x_write_vsi(struct tda998x_priv *priv, | |
| const struct drm_display_mode *mode) | |
| { | |
| union hdmi_infoframe frame; | |
| if (drm_hdmi_vendor_infoframe_from_display_mode(&frame.vendor.hdmi, | |
| &priv->connector, | |
| mode)) | |
| reg_clear(priv, REG_DIP_IF_FLAGS, DIP_IF_FLAGS_IF1); | |
| else | |
| tda998x_write_if(priv, DIP_IF_FLAGS_IF1, REG_IF1_HB0, &frame); | |
| } | |
| /* Audio support */ | |
| static const struct tda998x_audio_route tda998x_audio_route[AUDIO_ROUTE_NUM] = { | |
| [AUDIO_ROUTE_I2S] = { | |
| .ena_aclk = 1, | |
| .mux_ap = MUX_AP_SELECT_I2S, | |
| .aip_clksel = AIP_CLKSEL_AIP_I2S | AIP_CLKSEL_FS_ACLK, | |
| }, | |
| [AUDIO_ROUTE_SPDIF] = { | |
| .ena_aclk = 0, | |
| .mux_ap = MUX_AP_SELECT_SPDIF, | |
| .aip_clksel = AIP_CLKSEL_AIP_SPDIF | AIP_CLKSEL_FS_FS64SPDIF, | |
| }, | |
| }; | |
| /* Configure the TDA998x audio data and clock routing. */ | |
| static int tda998x_derive_routing(struct tda998x_priv *priv, | |
| struct tda998x_audio_settings *s, | |
| unsigned int route) | |
| { | |
| s->route = &tda998x_audio_route[route]; | |
| s->ena_ap = priv->audio_port_enable[route]; | |
| if (s->ena_ap == 0) { | |
| dev_err(&priv->hdmi->dev, "no audio configuration found\n"); | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| /* | |
| * The audio clock divisor register controls a divider producing Audio_Clk_Out | |
| * from SERclk by dividing it by 2^n where 0 <= n <= 5. We don't know what | |
| * Audio_Clk_Out or SERclk are. We guess SERclk is the same as TMDS clock. | |
| * | |
| * It seems that Audio_Clk_Out must be the smallest value that is greater | |
| * than 128*fs, otherwise audio does not function. There is some suggestion | |
| * that 126*fs is a better value. | |
| */ | |
| static u8 tda998x_get_adiv(struct tda998x_priv *priv, unsigned int fs) | |
| { | |
| unsigned long min_audio_clk = fs * 128; | |
| unsigned long ser_clk = priv->tmds_clock * 1000; | |
| u8 adiv; | |
| for (adiv = AUDIO_DIV_SERCLK_32; adiv != AUDIO_DIV_SERCLK_1; adiv--) | |
| if (ser_clk > min_audio_clk << adiv) | |
| break; | |
| dev_dbg(&priv->hdmi->dev, | |
| "ser_clk=%luHz fs=%uHz min_aclk=%luHz adiv=%d\n", | |
| ser_clk, fs, min_audio_clk, adiv); | |
| return adiv; | |
| } | |
| /* | |
| * In auto-CTS mode, the TDA998x uses a "measured time stamp" counter to | |
| * generate the CTS value. It appears that the "measured time stamp" is | |
| * the number of TDMS clock cycles within a number of audio input clock | |
| * cycles defined by the k and N parameters defined below, in a similar | |
| * way to that which is set out in the CTS generation in the HDMI spec. | |
| * | |
| * tmdsclk ----> mts -> /m ---> CTS | |
| * ^ | |
| * sclk -> /k -> /N | |
| * | |
| * CTS = mts / m, where m is 2^M. | |
| * /k is a divider based on the K value below, K+1 for K < 4, or 8 for K >= 4 | |
| * /N is a divider based on the HDMI specified N value. | |
| * | |
| * This produces the following equation: | |
| * CTS = tmds_clock * k * N / (sclk * m) | |
| * | |
| * When combined with the sink-side equation, and realising that sclk is | |
| * bclk_ratio * fs, we end up with: | |
| * k = m * bclk_ratio / 128. | |
| * | |
| * Note: S/PDIF always uses a bclk_ratio of 64. | |
| */ | |
| static int tda998x_derive_cts_n(struct tda998x_priv *priv, | |
| struct tda998x_audio_settings *settings, | |
| unsigned int ratio) | |
| { | |
| switch (ratio) { | |
| case 16: | |
| settings->cts_n = CTS_N_M(3) | CTS_N_K(0); | |
| break; | |
| case 32: | |
| settings->cts_n = CTS_N_M(3) | CTS_N_K(1); | |
| break; | |
| case 48: | |
| settings->cts_n = CTS_N_M(3) | CTS_N_K(2); | |
| break; | |
| case 64: | |
| settings->cts_n = CTS_N_M(3) | CTS_N_K(3); | |
| break; | |
| case 128: | |
| settings->cts_n = CTS_N_M(0) | CTS_N_K(0); | |
| break; | |
| default: | |
| dev_err(&priv->hdmi->dev, "unsupported bclk ratio %ufs\n", | |
| ratio); | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static void tda998x_audio_mute(struct tda998x_priv *priv, bool on) | |
| { | |
| if (on) { | |
| reg_set(priv, REG_SOFTRESET, SOFTRESET_AUDIO); | |
| reg_clear(priv, REG_SOFTRESET, SOFTRESET_AUDIO); | |
| reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); | |
| } else { | |
| reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); | |
| } | |
| } | |
| static void tda998x_configure_audio(struct tda998x_priv *priv) | |
| { | |
| const struct tda998x_audio_settings *settings = &priv->audio; | |
| u8 buf[6], adiv; | |
| u32 n; | |
| /* If audio is not configured, there is nothing to do. */ | |
| if (settings->ena_ap == 0) | |
| return; | |
| adiv = tda998x_get_adiv(priv, settings->sample_rate); | |
| /* Enable audio ports */ | |
| reg_write(priv, REG_ENA_AP, settings->ena_ap); | |
| reg_write(priv, REG_ENA_ACLK, settings->route->ena_aclk); | |
| reg_write(priv, REG_MUX_AP, settings->route->mux_ap); | |
| reg_write(priv, REG_I2S_FORMAT, settings->i2s_format); | |
| reg_write(priv, REG_AIP_CLKSEL, settings->route->aip_clksel); | |
| reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_LAYOUT | | |
| AIP_CNTRL_0_ACR_MAN); /* auto CTS */ | |
| reg_write(priv, REG_CTS_N, settings->cts_n); | |
| reg_write(priv, REG_AUDIO_DIV, adiv); | |
| /* | |
| * This is the approximate value of N, which happens to be | |
| * the recommended values for non-coherent clocks. | |
| */ | |
| n = 128 * settings->sample_rate / 1000; | |
| /* Write the CTS and N values */ | |
| buf[0] = 0x44; | |
| buf[1] = 0x42; | |
| buf[2] = 0x01; | |
| buf[3] = n; | |
| buf[4] = n >> 8; | |
| buf[5] = n >> 16; | |
| reg_write_range(priv, REG_ACR_CTS_0, buf, 6); | |
| /* Reset CTS generator */ | |
| reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS); | |
| reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS); | |
| /* Write the channel status | |
| * The REG_CH_STAT_B-registers skip IEC958 AES2 byte, because | |
| * there is a separate register for each I2S wire. | |
| */ | |
| buf[0] = settings->status[0]; | |
| buf[1] = settings->status[1]; | |
| buf[2] = settings->status[3]; | |
| buf[3] = settings->status[4]; | |
| reg_write_range(priv, REG_CH_STAT_B(0), buf, 4); | |
| tda998x_audio_mute(priv, true); | |
| msleep(20); | |
| tda998x_audio_mute(priv, false); | |
| tda998x_write_aif(priv, &settings->cea); | |
| } | |
| static int tda998x_audio_hw_params(struct device *dev, void *data, | |
| struct hdmi_codec_daifmt *daifmt, | |
| struct hdmi_codec_params *params) | |
| { | |
| struct tda998x_priv *priv = dev_get_drvdata(dev); | |
| unsigned int bclk_ratio; | |
| bool spdif = daifmt->fmt == HDMI_SPDIF; | |
| int ret; | |
| struct tda998x_audio_settings audio = { | |
| .sample_rate = params->sample_rate, | |
| .cea = params->cea, | |
| }; | |
| memcpy(audio.status, params->iec.status, | |
| min(sizeof(audio.status), sizeof(params->iec.status))); | |
| switch (daifmt->fmt) { | |
| case HDMI_I2S: | |
| audio.i2s_format = I2S_FORMAT_PHILIPS; | |
| break; | |
| case HDMI_LEFT_J: | |
| audio.i2s_format = I2S_FORMAT_LEFT_J; | |
| break; | |
| case HDMI_RIGHT_J: | |
| audio.i2s_format = I2S_FORMAT_RIGHT_J; | |
| break; | |
| case HDMI_SPDIF: | |
| audio.i2s_format = 0; | |
| break; | |
| default: | |
| dev_err(dev, "%s: Invalid format %d\n", __func__, daifmt->fmt); | |
| return -EINVAL; | |
| } | |
| if (!spdif && | |
| (daifmt->bit_clk_inv || daifmt->frame_clk_inv || | |
| daifmt->bit_clk_provider || daifmt->frame_clk_provider)) { | |
| dev_err(dev, "%s: Bad flags %d %d %d %d\n", __func__, | |
| daifmt->bit_clk_inv, daifmt->frame_clk_inv, | |
| daifmt->bit_clk_provider, | |
| daifmt->frame_clk_provider); | |
| return -EINVAL; | |
| } | |
| ret = tda998x_derive_routing(priv, &audio, AUDIO_ROUTE_I2S + spdif); | |
| if (ret < 0) | |
| return ret; | |
| bclk_ratio = spdif ? 64 : params->sample_width * 2; | |
| ret = tda998x_derive_cts_n(priv, &audio, bclk_ratio); | |
| if (ret < 0) | |
| return ret; | |
| mutex_lock(&priv->audio_mutex); | |
| priv->audio = audio; | |
| if (priv->supports_infoframes && priv->sink_has_audio) | |
| tda998x_configure_audio(priv); | |
| mutex_unlock(&priv->audio_mutex); | |
| return 0; | |
| } | |
| static void tda998x_audio_shutdown(struct device *dev, void *data) | |
| { | |
| struct tda998x_priv *priv = dev_get_drvdata(dev); | |
| mutex_lock(&priv->audio_mutex); | |
| reg_write(priv, REG_ENA_AP, 0); | |
| priv->audio.ena_ap = 0; | |
| mutex_unlock(&priv->audio_mutex); | |
| } | |
| static int tda998x_audio_mute_stream(struct device *dev, void *data, | |
| bool enable, int direction) | |
| { | |
| struct tda998x_priv *priv = dev_get_drvdata(dev); | |
| mutex_lock(&priv->audio_mutex); | |
| tda998x_audio_mute(priv, enable); | |
| mutex_unlock(&priv->audio_mutex); | |
| return 0; | |
| } | |
| static int tda998x_audio_get_eld(struct device *dev, void *data, | |
| uint8_t *buf, size_t len) | |
| { | |
| struct tda998x_priv *priv = dev_get_drvdata(dev); | |
| mutex_lock(&priv->audio_mutex); | |
| memcpy(buf, priv->connector.eld, | |
| min(sizeof(priv->connector.eld), len)); | |
| mutex_unlock(&priv->audio_mutex); | |
| return 0; | |
| } | |
| static const struct hdmi_codec_ops audio_codec_ops = { | |
| .hw_params = tda998x_audio_hw_params, | |
| .audio_shutdown = tda998x_audio_shutdown, | |
| .mute_stream = tda998x_audio_mute_stream, | |
| .get_eld = tda998x_audio_get_eld, | |
| }; | |
| static int tda998x_audio_codec_init(struct tda998x_priv *priv, | |
| struct device *dev) | |
| { | |
| struct hdmi_codec_pdata codec_data = { | |
| .ops = &audio_codec_ops, | |
| .max_i2s_channels = 2, | |
| .no_i2s_capture = 1, | |
| .no_spdif_capture = 1, | |
| .no_capture_mute = 1, | |
| }; | |
| if (priv->audio_port_enable[AUDIO_ROUTE_I2S]) | |
| codec_data.i2s = 1; | |
| if (priv->audio_port_enable[AUDIO_ROUTE_SPDIF]) | |
| codec_data.spdif = 1; | |
| priv->audio_pdev = platform_device_register_data( | |
| dev, HDMI_CODEC_DRV_NAME, PLATFORM_DEVID_AUTO, | |
| &codec_data, sizeof(codec_data)); | |
| return PTR_ERR_OR_ZERO(priv->audio_pdev); | |
| } | |
| /* DRM connector functions */ | |
| static enum drm_connector_status tda998x_conn_detect(struct tda998x_priv *priv) | |
| { | |
| u8 val = cec_read(priv, REG_CEC_RXSHPDLEV); | |
| return (val & CEC_RXSHPDLEV_HPD) ? connector_status_connected : | |
| connector_status_disconnected; | |
| } | |
| static enum drm_connector_status | |
| tda998x_connector_detect(struct drm_connector *connector, bool force) | |
| { | |
| struct tda998x_priv *priv = conn_to_tda998x_priv(connector); | |
| return tda998x_conn_detect(priv); | |
| } | |
| static const struct drm_connector_funcs tda998x_connector_funcs = { | |
| .reset = drm_atomic_helper_connector_reset, | |
| .fill_modes = drm_helper_probe_single_connector_modes, | |
| .detect = tda998x_connector_detect, | |
| .destroy = drm_connector_cleanup, | |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, | |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, | |
| }; | |
| static int read_edid_block(void *data, u8 *buf, unsigned int blk, size_t length) | |
| { | |
| struct tda998x_priv *priv = data; | |
| u8 offset, segptr; | |
| int ret, i; | |
| offset = (blk & 1) ? 128 : 0; | |
| segptr = blk / 2; | |
| mutex_lock(&priv->edid_mutex); | |
| reg_write(priv, REG_DDC_ADDR, 0xa0); | |
| reg_write(priv, REG_DDC_OFFS, offset); | |
| reg_write(priv, REG_DDC_SEGM_ADDR, 0x60); | |
| reg_write(priv, REG_DDC_SEGM, segptr); | |
| /* enable reading EDID: */ | |
| priv->wq_edid_wait = 1; | |
| reg_write(priv, REG_EDID_CTRL, 0x1); | |
| /* flag must be cleared by sw: */ | |
| reg_write(priv, REG_EDID_CTRL, 0x0); | |
| /* wait for block read to complete: */ | |
| if (priv->hdmi->irq) { | |
| i = wait_event_timeout(priv->wq_edid, | |
| !priv->wq_edid_wait, | |
| msecs_to_jiffies(100)); | |
| if (i < 0) { | |
| dev_err(&priv->hdmi->dev, "read edid wait err %d\n", i); | |
| ret = i; | |
| goto failed; | |
| } | |
| } else { | |
| for (i = 100; i > 0; i--) { | |
| msleep(1); | |
| ret = reg_read(priv, REG_INT_FLAGS_2); | |
| if (ret < 0) | |
| goto failed; | |
| if (ret & INT_FLAGS_2_EDID_BLK_RD) | |
| break; | |
| } | |
| } | |
| if (i == 0) { | |
| dev_err(&priv->hdmi->dev, "read edid timeout\n"); | |
| ret = -ETIMEDOUT; | |
| goto failed; | |
| } | |
| ret = reg_read_range(priv, REG_EDID_DATA_0, buf, length); | |
| if (ret != length) { | |
| dev_err(&priv->hdmi->dev, "failed to read edid block %d: %d\n", | |
| blk, ret); | |
| goto failed; | |
| } | |
| ret = 0; | |
| failed: | |
| mutex_unlock(&priv->edid_mutex); | |
| return ret; | |
| } | |
| static const struct drm_edid *tda998x_edid_read(struct tda998x_priv *priv, | |
| struct drm_connector *connector) | |
| { | |
| const struct drm_edid *drm_edid; | |
| /* | |
| * If we get killed while waiting for the HPD timeout, return | |
| * no modes found: we are not in a restartable path, so we | |
| * can't handle signals gracefully. | |
| */ | |
| if (tda998x_edid_delay_wait(priv)) | |
| return NULL; | |
| if (priv->rev == TDA19988) | |
| reg_clear(priv, REG_TX4, TX4_PD_RAM); | |
| drm_edid = drm_edid_read_custom(connector, read_edid_block, priv); | |
| if (priv->rev == TDA19988) | |
| reg_set(priv, REG_TX4, TX4_PD_RAM); | |
| return drm_edid; | |
| } | |
| static int tda998x_connector_get_modes(struct drm_connector *connector) | |
| { | |
| struct tda998x_priv *priv = conn_to_tda998x_priv(connector); | |
| const struct drm_edid *drm_edid; | |
| int n; | |
| drm_edid = tda998x_edid_read(priv, connector); | |
| drm_edid_connector_update(connector, drm_edid); | |
| cec_notifier_set_phys_addr(priv->cec_notify, | |
| connector->display_info.source_physical_address); | |
| if (!drm_edid) { | |
| dev_warn(&priv->hdmi->dev, "failed to read EDID\n"); | |
| return 0; | |
| } | |
| mutex_lock(&priv->audio_mutex); | |
| n = drm_edid_connector_add_modes(connector); | |
| priv->sink_has_audio = connector->display_info.has_audio; | |
| mutex_unlock(&priv->audio_mutex); | |
| drm_edid_free(drm_edid); | |
| return n; | |
| } | |
| static struct drm_encoder * | |
| tda998x_connector_best_encoder(struct drm_connector *connector) | |
| { | |
| struct tda998x_priv *priv = conn_to_tda998x_priv(connector); | |
| return priv->bridge.encoder; | |
| } | |
| static | |
| const struct drm_connector_helper_funcs tda998x_connector_helper_funcs = { | |
| .get_modes = tda998x_connector_get_modes, | |
| .best_encoder = tda998x_connector_best_encoder, | |
| }; | |
| static int tda998x_connector_init(struct tda998x_priv *priv, | |
| struct drm_device *drm) | |
| { | |
| struct drm_connector *connector = &priv->connector; | |
| int ret; | |
| connector->interlace_allowed = 1; | |
| if (priv->hdmi->irq) | |
| connector->polled = DRM_CONNECTOR_POLL_HPD; | |
| else | |
| connector->polled = DRM_CONNECTOR_POLL_CONNECT | | |
| DRM_CONNECTOR_POLL_DISCONNECT; | |
| drm_connector_helper_add(connector, &tda998x_connector_helper_funcs); | |
| ret = drm_connector_init(drm, connector, &tda998x_connector_funcs, | |
| DRM_MODE_CONNECTOR_HDMIA); | |
| if (ret) | |
| return ret; | |
| drm_connector_attach_encoder(&priv->connector, | |
| priv->bridge.encoder); | |
| return 0; | |
| } | |
| /* DRM bridge functions */ | |
| static int tda998x_bridge_attach(struct drm_bridge *bridge, | |
| struct drm_encoder *encoder, | |
| enum drm_bridge_attach_flags flags) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) | |
| return 0; | |
| return tda998x_connector_init(priv, bridge->dev); | |
| } | |
| static void tda998x_bridge_detach(struct drm_bridge *bridge) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| if (priv->connector.dev) | |
| drm_connector_cleanup(&priv->connector); | |
| } | |
| static enum drm_mode_status tda998x_bridge_mode_valid(struct drm_bridge *bridge, | |
| const struct drm_display_info *info, | |
| const struct drm_display_mode *mode) | |
| { | |
| /* TDA19988 dotclock can go up to 165MHz */ | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| if (mode->clock > ((priv->rev == TDA19988) ? 165000 : 150000)) | |
| return MODE_CLOCK_HIGH; | |
| if (mode->htotal >= BIT(13)) | |
| return MODE_BAD_HVALUE; | |
| if (mode->vtotal >= BIT(11)) | |
| return MODE_BAD_VVALUE; | |
| return MODE_OK; | |
| } | |
| static void tda998x_bridge_enable(struct drm_bridge *bridge, | |
| struct drm_atomic_commit *commit) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| if (!priv->is_on) { | |
| /* enable video ports, audio will be enabled later */ | |
| reg_write(priv, REG_ENA_VP_0, 0xff); | |
| reg_write(priv, REG_ENA_VP_1, 0xff); | |
| reg_write(priv, REG_ENA_VP_2, 0xff); | |
| /* set muxing after enabling ports: */ | |
| reg_write(priv, REG_VIP_CNTRL_0, priv->vip_cntrl_0); | |
| reg_write(priv, REG_VIP_CNTRL_1, priv->vip_cntrl_1); | |
| reg_write(priv, REG_VIP_CNTRL_2, priv->vip_cntrl_2); | |
| priv->is_on = true; | |
| } | |
| } | |
| static void tda998x_bridge_disable(struct drm_bridge *bridge, | |
| struct drm_atomic_commit *commit) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| if (priv->is_on) { | |
| /* disable video ports */ | |
| reg_write(priv, REG_ENA_VP_0, 0x00); | |
| reg_write(priv, REG_ENA_VP_1, 0x00); | |
| reg_write(priv, REG_ENA_VP_2, 0x00); | |
| priv->is_on = false; | |
| } | |
| } | |
| static void tda998x_bridge_mode_set(struct drm_bridge *bridge, | |
| const struct drm_display_mode *mode, | |
| const struct drm_display_mode *adjusted_mode) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| unsigned long tmds_clock; | |
| u16 ref_pix, ref_line, n_pix, n_line; | |
| u16 hs_pix_s, hs_pix_e; | |
| u16 vs1_pix_s, vs1_pix_e, vs1_line_s, vs1_line_e; | |
| u16 vs2_pix_s, vs2_pix_e, vs2_line_s, vs2_line_e; | |
| u16 vwin1_line_s, vwin1_line_e; | |
| u16 vwin2_line_s, vwin2_line_e; | |
| u16 de_pix_s, de_pix_e; | |
| u8 reg, div, rep, sel_clk; | |
| /* | |
| * Since we are "computer" like, our source invariably produces | |
| * full-range RGB. If the monitor supports full-range, then use | |
| * it, otherwise reduce to limited-range. | |
| */ | |
| priv->rgb_quant_range = | |
| priv->connector.display_info.rgb_quant_range_selectable ? | |
| HDMI_QUANTIZATION_RANGE_FULL : | |
| drm_default_rgb_quant_range(adjusted_mode); | |
| /* | |
| * Internally TDA998x is using ITU-R BT.656 style sync but | |
| * we get VESA style sync. TDA998x is using a reference pixel | |
| * relative to ITU to sync to the input frame and for output | |
| * sync generation. Currently, we are using reference detection | |
| * from HS/VS, i.e. REFPIX/REFLINE denote frame start sync point | |
| * which is position of rising VS with coincident rising HS. | |
| * | |
| * Now there is some issues to take care of: | |
| * - HDMI data islands require sync-before-active | |
| * - TDA998x register values must be > 0 to be enabled | |
| * - REFLINE needs an additional offset of +1 | |
| * - REFPIX needs an addtional offset of +1 for UYUV and +3 for RGB | |
| * | |
| * So we add +1 to all horizontal and vertical register values, | |
| * plus an additional +3 for REFPIX as we are using RGB input only. | |
| */ | |
| n_pix = mode->htotal; | |
| n_line = mode->vtotal; | |
| hs_pix_e = mode->hsync_end - mode->hdisplay; | |
| hs_pix_s = mode->hsync_start - mode->hdisplay; | |
| de_pix_e = mode->htotal; | |
| de_pix_s = mode->htotal - mode->hdisplay; | |
| ref_pix = 3 + hs_pix_s; | |
| /* | |
| * Attached LCD controllers may generate broken sync. Allow | |
| * those to adjust the position of the rising VS edge by adding | |
| * HSKEW to ref_pix. | |
| */ | |
| if (adjusted_mode->flags & DRM_MODE_FLAG_HSKEW) | |
| ref_pix += adjusted_mode->hskew; | |
| if ((mode->flags & DRM_MODE_FLAG_INTERLACE) == 0) { | |
| ref_line = 1 + mode->vsync_start - mode->vdisplay; | |
| vwin1_line_s = mode->vtotal - mode->vdisplay - 1; | |
| vwin1_line_e = vwin1_line_s + mode->vdisplay; | |
| vs1_pix_s = vs1_pix_e = hs_pix_s; | |
| vs1_line_s = mode->vsync_start - mode->vdisplay; | |
| vs1_line_e = vs1_line_s + | |
| mode->vsync_end - mode->vsync_start; | |
| vwin2_line_s = vwin2_line_e = 0; | |
| vs2_pix_s = vs2_pix_e = 0; | |
| vs2_line_s = vs2_line_e = 0; | |
| } else { | |
| ref_line = 1 + (mode->vsync_start - mode->vdisplay)/2; | |
| vwin1_line_s = (mode->vtotal - mode->vdisplay)/2; | |
| vwin1_line_e = vwin1_line_s + mode->vdisplay/2; | |
| vs1_pix_s = vs1_pix_e = hs_pix_s; | |
| vs1_line_s = (mode->vsync_start - mode->vdisplay)/2; | |
| vs1_line_e = vs1_line_s + | |
| (mode->vsync_end - mode->vsync_start)/2; | |
| vwin2_line_s = vwin1_line_s + mode->vtotal/2; | |
| vwin2_line_e = vwin2_line_s + mode->vdisplay/2; | |
| vs2_pix_s = vs2_pix_e = hs_pix_s + mode->htotal/2; | |
| vs2_line_s = vs1_line_s + mode->vtotal/2 ; | |
| vs2_line_e = vs2_line_s + | |
| (mode->vsync_end - mode->vsync_start)/2; | |
| } | |
| /* | |
| * Select pixel repeat depending on the double-clock flag | |
| * (which means we have to repeat each pixel once.) | |
| */ | |
| rep = mode->flags & DRM_MODE_FLAG_DBLCLK ? 1 : 0; | |
| sel_clk = SEL_CLK_ENA_SC_CLK | SEL_CLK_SEL_CLK1 | | |
| SEL_CLK_SEL_VRF_CLK(rep ? 2 : 0); | |
| /* the TMDS clock is scaled up by the pixel repeat */ | |
| tmds_clock = mode->clock * (1 + rep); | |
| /* | |
| * The divisor is power-of-2. The TDA9983B datasheet gives | |
| * this as ranges of Msample/s, which is 10x the TMDS clock: | |
| * 0 - 800 to 1500 Msample/s | |
| * 1 - 400 to 800 Msample/s | |
| * 2 - 200 to 400 Msample/s | |
| * 3 - as 2 above | |
| */ | |
| for (div = 0; div < 3; div++) | |
| if (80000 >> div <= tmds_clock) | |
| break; | |
| mutex_lock(&priv->audio_mutex); | |
| priv->tmds_clock = tmds_clock; | |
| /* mute the audio FIFO: */ | |
| reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); | |
| /* set HDMI HDCP mode off: */ | |
| reg_write(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS); | |
| reg_clear(priv, REG_TX33, TX33_HDMI); | |
| reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(0)); | |
| /* no pre-filter or interpolator: */ | |
| reg_write(priv, REG_HVF_CNTRL_0, HVF_CNTRL_0_PREFIL(0) | | |
| HVF_CNTRL_0_INTPOL(0)); | |
| reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_PREFILT); | |
| reg_write(priv, REG_VIP_CNTRL_5, VIP_CNTRL_5_SP_CNT(0)); | |
| reg_write(priv, REG_VIP_CNTRL_4, VIP_CNTRL_4_BLANKIT(0) | | |
| VIP_CNTRL_4_BLC(0)); | |
| reg_clear(priv, REG_PLL_SERIAL_1, PLL_SERIAL_1_SRL_MAN_IZ); | |
| reg_clear(priv, REG_PLL_SERIAL_3, PLL_SERIAL_3_SRL_CCIR | | |
| PLL_SERIAL_3_SRL_DE); | |
| reg_write(priv, REG_SERIALIZER, 0); | |
| reg_write(priv, REG_HVF_CNTRL_1, HVF_CNTRL_1_VQR(0)); | |
| reg_write(priv, REG_RPT_CNTRL, RPT_CNTRL_REPEAT(rep)); | |
| reg_write(priv, REG_SEL_CLK, sel_clk); | |
| reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(div) | | |
| PLL_SERIAL_2_SRL_PR(rep)); | |
| /* set color matrix according to output rgb quant range */ | |
| if (priv->rgb_quant_range == HDMI_QUANTIZATION_RANGE_LIMITED) { | |
| static u8 tda998x_full_to_limited_range[] = { | |
| MAT_CONTRL_MAT_SC(2), | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x03, 0x6f, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x03, 0x6f, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0x03, 0x6f, | |
| 0x00, 0x40, 0x00, 0x40, 0x00, 0x40 | |
| }; | |
| reg_clear(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC); | |
| reg_write_range(priv, REG_MAT_CONTRL, | |
| tda998x_full_to_limited_range, | |
| sizeof(tda998x_full_to_limited_range)); | |
| } else { | |
| reg_write(priv, REG_MAT_CONTRL, MAT_CONTRL_MAT_BP | | |
| MAT_CONTRL_MAT_SC(1)); | |
| reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC); | |
| } | |
| /* set BIAS tmds value: */ | |
| reg_write(priv, REG_ANA_GENERAL, 0x09); | |
| /* | |
| * Sync on rising HSYNC/VSYNC | |
| */ | |
| reg = VIP_CNTRL_3_SYNC_HS; | |
| /* | |
| * TDA19988 requires high-active sync at input stage, | |
| * so invert low-active sync provided by master encoder here | |
| */ | |
| if (mode->flags & DRM_MODE_FLAG_NHSYNC) | |
| reg |= VIP_CNTRL_3_H_TGL; | |
| if (mode->flags & DRM_MODE_FLAG_NVSYNC) | |
| reg |= VIP_CNTRL_3_V_TGL; | |
| reg_write(priv, REG_VIP_CNTRL_3, reg); | |
| reg_write(priv, REG_VIDFORMAT, 0x00); | |
| reg_write16(priv, REG_REFPIX_MSB, ref_pix); | |
| reg_write16(priv, REG_REFLINE_MSB, ref_line); | |
| reg_write16(priv, REG_NPIX_MSB, n_pix); | |
| reg_write16(priv, REG_NLINE_MSB, n_line); | |
| reg_write16(priv, REG_VS_LINE_STRT_1_MSB, vs1_line_s); | |
| reg_write16(priv, REG_VS_PIX_STRT_1_MSB, vs1_pix_s); | |
| reg_write16(priv, REG_VS_LINE_END_1_MSB, vs1_line_e); | |
| reg_write16(priv, REG_VS_PIX_END_1_MSB, vs1_pix_e); | |
| reg_write16(priv, REG_VS_LINE_STRT_2_MSB, vs2_line_s); | |
| reg_write16(priv, REG_VS_PIX_STRT_2_MSB, vs2_pix_s); | |
| reg_write16(priv, REG_VS_LINE_END_2_MSB, vs2_line_e); | |
| reg_write16(priv, REG_VS_PIX_END_2_MSB, vs2_pix_e); | |
| reg_write16(priv, REG_HS_PIX_START_MSB, hs_pix_s); | |
| reg_write16(priv, REG_HS_PIX_STOP_MSB, hs_pix_e); | |
| reg_write16(priv, REG_VWIN_START_1_MSB, vwin1_line_s); | |
| reg_write16(priv, REG_VWIN_END_1_MSB, vwin1_line_e); | |
| reg_write16(priv, REG_VWIN_START_2_MSB, vwin2_line_s); | |
| reg_write16(priv, REG_VWIN_END_2_MSB, vwin2_line_e); | |
| reg_write16(priv, REG_DE_START_MSB, de_pix_s); | |
| reg_write16(priv, REG_DE_STOP_MSB, de_pix_e); | |
| if (priv->rev == TDA19988) { | |
| /* let incoming pixels fill the active space (if any) */ | |
| reg_write(priv, REG_ENABLE_SPACE, 0x00); | |
| } | |
| /* | |
| * Always generate sync polarity relative to input sync and | |
| * revert input stage toggled sync at output stage | |
| */ | |
| reg = TBG_CNTRL_1_DWIN_DIS | TBG_CNTRL_1_TGL_EN; | |
| if (mode->flags & DRM_MODE_FLAG_NHSYNC) | |
| reg |= TBG_CNTRL_1_H_TGL; | |
| if (mode->flags & DRM_MODE_FLAG_NVSYNC) | |
| reg |= TBG_CNTRL_1_V_TGL; | |
| reg_write(priv, REG_TBG_CNTRL_1, reg); | |
| /* must be last register set: */ | |
| reg_write(priv, REG_TBG_CNTRL_0, 0); | |
| /* CEA-861B section 6 says that: | |
| * CEA version 1 (CEA-861) has no support for infoframes. | |
| * CEA version 2 (CEA-861A) supports version 1 AVI infoframes, | |
| * and optional basic audio. | |
| * CEA version 3 (CEA-861B) supports version 1 and 2 AVI infoframes, | |
| * and optional digital audio, with audio infoframes. | |
| * | |
| * Since we only support generation of version 2 AVI infoframes, | |
| * ignore CEA version 2 and below (iow, behave as if we're a | |
| * CEA-861 source.) | |
| */ | |
| priv->supports_infoframes = priv->connector.display_info.cea_rev >= 3; | |
| if (priv->supports_infoframes) { | |
| /* We need to turn HDMI HDCP stuff on to get audio through */ | |
| reg &= ~TBG_CNTRL_1_DWIN_DIS; | |
| reg_write(priv, REG_TBG_CNTRL_1, reg); | |
| reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(1)); | |
| reg_set(priv, REG_TX33, TX33_HDMI); | |
| tda998x_write_avi(priv, adjusted_mode); | |
| tda998x_write_vsi(priv, adjusted_mode); | |
| if (priv->sink_has_audio) | |
| tda998x_configure_audio(priv); | |
| } | |
| mutex_unlock(&priv->audio_mutex); | |
| } | |
| static const struct drm_edid * | |
| tda998x_bridge_edid_read(struct drm_bridge *bridge, | |
| struct drm_connector *connector) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| const struct drm_edid *drm_edid; | |
| const struct edid *edid; | |
| drm_edid = tda998x_edid_read(priv, connector); | |
| if (!drm_edid) { | |
| dev_dbg(&priv->hdmi->dev, "failed to get edid\n"); | |
| return NULL; | |
| } | |
| /* | |
| * FIXME: This should use connector->display_info.has_audio from | |
| * a path that has read the EDID and called | |
| * drm_edid_connector_update(). | |
| */ | |
| edid = drm_edid_raw(drm_edid); | |
| dev_dbg(&priv->hdmi->dev, "got edid: width[%d] x height[%d]\n", | |
| edid->width_cm, edid->height_cm); | |
| priv->sink_has_audio = drm_detect_monitor_audio(edid); | |
| cec_notifier_set_phys_addr_from_edid(priv->cec_notify, edid); | |
| return drm_edid; | |
| } | |
| static enum drm_connector_status | |
| tda998x_bridge_detect(struct drm_bridge *bridge, | |
| struct drm_connector *connector) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| return tda998x_conn_detect(priv); | |
| } | |
| static void tda998x_bridge_hpd_enable(struct drm_bridge *bridge) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, CEC_RXSHPDLEV_HPD); | |
| } | |
| static void tda998x_bridge_hpd_disable(struct drm_bridge *bridge) | |
| { | |
| struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, 0); | |
| } | |
| static const struct drm_bridge_funcs tda998x_bridge_funcs = { | |
| .atomic_create_state = drm_atomic_helper_bridge_create_state, | |
| .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, | |
| .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, | |
| .attach = tda998x_bridge_attach, | |
| .detach = tda998x_bridge_detach, | |
| .mode_valid = tda998x_bridge_mode_valid, | |
| .atomic_disable = tda998x_bridge_disable, | |
| .mode_set = tda998x_bridge_mode_set, | |
| .atomic_enable = tda998x_bridge_enable, | |
| .edid_read = tda998x_bridge_edid_read, | |
| .detect = tda998x_bridge_detect, | |
| .hpd_enable = tda998x_bridge_hpd_enable, | |
| .hpd_disable = tda998x_bridge_hpd_disable, | |
| }; | |
| /* I2C driver functions */ | |
| static int tda998x_get_audio_ports(struct tda998x_priv *priv, | |
| struct device_node *np) | |
| { | |
| const __be32 *port_data; | |
| u32 size; | |
| int i; | |
| port_data = of_get_property(np, "audio-ports", &size); | |
| if (!port_data) | |
| return 0; | |
| size /= sizeof(u32); | |
| if (size > 2 * ARRAY_SIZE(priv->audio_port_enable) || size % 2 != 0) { | |
| dev_err(&priv->hdmi->dev, | |
| "Bad number of elements in audio-ports dt-property\n"); | |
| return -EINVAL; | |
| } | |
| size /= 2; | |
| for (i = 0; i < size; i++) { | |
| unsigned int route; | |
| u8 afmt = be32_to_cpup(&port_data[2*i]); | |
| u8 ena_ap = be32_to_cpup(&port_data[2*i+1]); | |
| switch (afmt) { | |
| case TDA998x_I2S: | |
| route = AUDIO_ROUTE_I2S; | |
| break; | |
| case TDA998x_SPDIF: | |
| route = AUDIO_ROUTE_SPDIF; | |
| break; | |
| default: | |
| dev_err(&priv->hdmi->dev, | |
| "Bad audio format %u\n", afmt); | |
| return -EINVAL; | |
| } | |
| if (!ena_ap) { | |
| dev_err(&priv->hdmi->dev, "invalid zero port config\n"); | |
| continue; | |
| } | |
| if (priv->audio_port_enable[route]) { | |
| dev_err(&priv->hdmi->dev, | |
| "%s format already configured\n", | |
| route == AUDIO_ROUTE_SPDIF ? "SPDIF" : "I2S"); | |
| return -EINVAL; | |
| } | |
| priv->audio_port_enable[route] = ena_ap; | |
| } | |
| return 0; | |
| } | |
| static int | |
| tda998x_probe(struct i2c_client *client) | |
| { | |
| struct device_node *np = client->dev.of_node; | |
| struct device *dev = &client->dev; | |
| struct i2c_board_info cec_info; | |
| struct tda998x_priv *priv; | |
| int rev_lo, rev_hi, ret; | |
| u32 video; | |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { | |
| dev_warn(&client->dev, "adapter does not support I2C\n"); | |
| return -EIO; | |
| } | |
| priv = devm_drm_bridge_alloc(dev, struct tda998x_priv, bridge, &tda998x_bridge_funcs); | |
| if (IS_ERR(priv)) | |
| return PTR_ERR(priv); | |
| dev_set_drvdata(dev, priv); | |
| mutex_init(&priv->mutex); /* protect the page access */ | |
| mutex_init(&priv->audio_mutex); /* protect access from audio thread */ | |
| mutex_init(&priv->edid_mutex); | |
| INIT_LIST_HEAD(&priv->bridge.list); | |
| init_waitqueue_head(&priv->edid_delay_waitq); | |
| timer_setup(&priv->edid_delay_timer, tda998x_edid_delay_done, 0); | |
| INIT_WORK(&priv->detect_work, tda998x_detect_work); | |
| priv->vip_cntrl_0 = VIP_CNTRL_0_SWAP_A(2) | VIP_CNTRL_0_SWAP_B(3); | |
| priv->vip_cntrl_1 = VIP_CNTRL_1_SWAP_C(0) | VIP_CNTRL_1_SWAP_D(1); | |
| priv->vip_cntrl_2 = VIP_CNTRL_2_SWAP_E(4) | VIP_CNTRL_2_SWAP_F(5); | |
| /* CEC I2C address bound to TDA998x I2C addr by configuration pins */ | |
| priv->cec_addr = 0x34 + (client->addr & 0x03); | |
| priv->current_page = 0xff; | |
| priv->hdmi = client; | |
| /* wake up the device: */ | |
| cec_write(priv, REG_CEC_ENAMODS, | |
| CEC_ENAMODS_EN_RXSENS | CEC_ENAMODS_EN_HDMI); | |
| tda998x_reset(priv); | |
| /* read version: */ | |
| rev_lo = reg_read(priv, REG_VERSION_LSB); | |
| if (rev_lo < 0) { | |
| dev_err(dev, "failed to read version: %d\n", rev_lo); | |
| ret = rev_lo; | |
| goto cancel_work; | |
| } | |
| rev_hi = reg_read(priv, REG_VERSION_MSB); | |
| if (rev_hi < 0) { | |
| dev_err(dev, "failed to read version: %d\n", rev_hi); | |
| ret = rev_hi; | |
| goto cancel_work; | |
| } | |
| priv->rev = rev_lo | rev_hi << 8; | |
| /* mask off feature bits: */ | |
| priv->rev &= ~0x30; /* not-hdcp and not-scalar bit */ | |
| switch (priv->rev) { | |
| case TDA9989N2: | |
| dev_info(dev, "found TDA9989 n2"); | |
| break; | |
| case TDA19989: | |
| dev_info(dev, "found TDA19989"); | |
| break; | |
| case TDA19989N2: | |
| dev_info(dev, "found TDA19989 n2"); | |
| break; | |
| case TDA19988: | |
| dev_info(dev, "found TDA19988"); | |
| break; | |
| default: | |
| dev_err(dev, "found unsupported device: %04x\n", priv->rev); | |
| ret = -ENXIO; | |
| goto cancel_work; | |
| } | |
| /* after reset, enable DDC: */ | |
| reg_write(priv, REG_DDC_DISABLE, 0x00); | |
| /* set clock on DDC channel: */ | |
| reg_write(priv, REG_TX3, 39); | |
| /* if necessary, disable multi-master: */ | |
| if (priv->rev == TDA19989) | |
| reg_set(priv, REG_I2C_MASTER, I2C_MASTER_DIS_MM); | |
| cec_write(priv, REG_CEC_FRO_IM_CLK_CTRL, | |
| CEC_FRO_IM_CLK_CTRL_GHOST_DIS | CEC_FRO_IM_CLK_CTRL_IMCLK_SEL); | |
| /* ensure interrupts are disabled */ | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, 0); | |
| /* clear pending interrupts */ | |
| cec_read(priv, REG_CEC_RXSHPDINT); | |
| reg_read(priv, REG_INT_FLAGS_0); | |
| reg_read(priv, REG_INT_FLAGS_1); | |
| reg_read(priv, REG_INT_FLAGS_2); | |
| /* initialize the optional IRQ */ | |
| if (client->irq) { | |
| unsigned long irq_flags; | |
| /* init read EDID waitqueue and HDP work */ | |
| init_waitqueue_head(&priv->wq_edid); | |
| irq_flags = | |
| irqd_get_trigger_type(irq_get_irq_data(client->irq)); | |
| priv->cec_glue.irq_flags = irq_flags; | |
| irq_flags |= IRQF_SHARED | IRQF_ONESHOT; | |
| ret = request_threaded_irq(client->irq, NULL, | |
| tda998x_irq_thread, irq_flags, | |
| "tda998x", priv); | |
| if (ret) { | |
| dev_err(dev, "failed to request IRQ#%u: %d\n", | |
| client->irq, ret); | |
| goto cancel_work; | |
| } | |
| /* enable HPD irq */ | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, CEC_RXSHPDLEV_HPD); | |
| priv->bridge.ops = DRM_BRIDGE_OP_HPD; | |
| } | |
| priv->cec_notify = cec_notifier_conn_register(dev, NULL, NULL); | |
| if (!priv->cec_notify) { | |
| ret = -ENOMEM; | |
| goto free_irq; | |
| } | |
| priv->cec_glue.parent = dev; | |
| priv->cec_glue.data = priv; | |
| priv->cec_glue.init = tda998x_cec_hook_init; | |
| priv->cec_glue.exit = tda998x_cec_hook_exit; | |
| priv->cec_glue.open = tda998x_cec_hook_open; | |
| priv->cec_glue.release = tda998x_cec_hook_release; | |
| /* | |
| * Some TDA998x are actually two I2C devices merged onto one piece | |
| * of silicon: TDA9989 and TDA19989 combine the HDMI transmitter | |
| * with a slightly modified TDA9950 CEC device. The CEC device | |
| * is at the TDA9950 address, with the address pins strapped across | |
| * to the TDA998x address pins. Hence, it always has the same | |
| * offset. | |
| */ | |
| memset(&cec_info, 0, sizeof(cec_info)); | |
| strscpy(cec_info.type, "tda9950", sizeof(cec_info.type)); | |
| cec_info.addr = priv->cec_addr; | |
| cec_info.platform_data = &priv->cec_glue; | |
| cec_info.irq = client->irq; | |
| priv->cec = i2c_new_client_device(client->adapter, &cec_info); | |
| if (IS_ERR(priv->cec)) { | |
| ret = PTR_ERR(priv->cec); | |
| goto notifier_conn_unregister; | |
| } | |
| /* enable EDID read irq: */ | |
| reg_set(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD); | |
| if (np) { | |
| /* get the device tree parameters */ | |
| ret = of_property_read_u32(np, "video-ports", &video); | |
| if (ret == 0) { | |
| priv->vip_cntrl_0 = video >> 16; | |
| priv->vip_cntrl_1 = video >> 8; | |
| priv->vip_cntrl_2 = video; | |
| } | |
| ret = tda998x_get_audio_ports(priv, np); | |
| if (ret) | |
| goto unregister_dev; | |
| if (priv->audio_port_enable[AUDIO_ROUTE_I2S] || | |
| priv->audio_port_enable[AUDIO_ROUTE_SPDIF]) | |
| tda998x_audio_codec_init(priv, &client->dev); | |
| } | |
| #ifdef CONFIG_OF | |
| priv->bridge.of_node = dev->of_node; | |
| #endif | |
| priv->bridge.ops |= DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_DETECT; | |
| priv->bridge.type = DRM_MODE_CONNECTOR_HDMIA; | |
| drm_bridge_add(&priv->bridge); | |
| return 0; | |
| unregister_dev: | |
| i2c_unregister_device(priv->cec); | |
| notifier_conn_unregister: | |
| cec_notifier_conn_unregister(priv->cec_notify); | |
| free_irq: | |
| if (client->irq) { | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, 0); | |
| reg_clear(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD); | |
| free_irq(client->irq, priv); | |
| } | |
| cancel_work: | |
| timer_delete_sync(&priv->edid_delay_timer); | |
| cancel_work_sync(&priv->detect_work); | |
| return ret; | |
| } | |
| static void tda998x_remove(struct i2c_client *client) | |
| { | |
| struct tda998x_priv *priv = dev_get_drvdata(&client->dev); | |
| drm_bridge_remove(&priv->bridge); | |
| if (priv->audio_pdev) | |
| platform_device_unregister(priv->audio_pdev); | |
| i2c_unregister_device(priv->cec); | |
| cec_notifier_conn_unregister(priv->cec_notify); | |
| /* disable all IRQs and free the IRQ handler */ | |
| if (client->irq) { | |
| cec_write(priv, REG_CEC_RXSHPDINTENA, 0); | |
| reg_clear(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD); | |
| free_irq(priv->hdmi->irq, priv); | |
| } | |
| timer_delete_sync(&priv->edid_delay_timer); | |
| cancel_work_sync(&priv->detect_work); | |
| } | |
| #ifdef CONFIG_OF | |
| static const struct of_device_id tda998x_dt_ids[] = { | |
| { .compatible = "nxp,tda998x", }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, tda998x_dt_ids); | |
| #endif | |
| static const struct i2c_device_id tda998x_ids[] = { | |
| { .name = "tda998x" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, tda998x_ids); | |
| static struct i2c_driver tda998x_driver = { | |
| .probe = tda998x_probe, | |
| .remove = tda998x_remove, | |
| .driver = { | |
| .name = "tda998x", | |
| .of_match_table = of_match_ptr(tda998x_dt_ids), | |
| }, | |
| .id_table = tda998x_ids, | |
| }; | |
| module_i2c_driver(tda998x_driver); | |
| MODULE_AUTHOR("Rob Clark <robdclark@gmail.com"); | |
| MODULE_DESCRIPTION("NXP Semiconductors TDA998X HDMI Encoder"); | |
| MODULE_LICENSE("GPL"); |